PCE-3132 user manual ed.2€¦ · This manual is for the PCE-3132. Part No. 2002313201 Edition 2...

User Manual

PCE-3132

Socket-M 478 Intel® CoreTM 2 Duo/ Core Duo/ Celeron® M PCIe Half-sized SBC with PCI Express/VGA/LVDS/GbE LAN

CopyrightThe documentation and the software included with this product are copyrighted 2008by Advantech Co., Ltd. All rights are reserved. Advantech Co., Ltd. reserves the rightto make improvements in the products described in this manual at any time withoutnotice. No part of this manual may be reproduced, copied, translated or transmittedin any form or by any means without the prior written permission of Advantech Co.,Ltd. Information provided in this manual is intended to be accurate and reliable. How-ever, Advantech Co., Ltd. assumes no responsibility for its use, nor for any infringe-ments of the rights of third parties, which may result from its use.

AcknowledgementsAward is a trademark of Award Software International, Inc.VIA is a trademark of VIA Technologies, Inc. IBM, PC/AT, PS/2 and VGA are trademarks of International Business Machines Cor-poration. Intel and Pentium are trademarks of Intel Corporation. Microsoft Windows® is a registered trademark of Microsoft Corp. RTL is a trademark of Realtek Semi-Conductor Co., Ltd.ESS is a trademark of ESS Technology, Inc. UMC is a trademark of United Microelectronics Corporation. SMI is a trademark of Silicon Motion, Inc. Creative is a trademark of Creative Technology LTD. All other product names or trademarks are properties of their respective owners. For more information on this and other Advantech products, please visit our websitesat: http://www.advantech.com http://www.advantech.com/eplatform For technical support and service, please visit our support website at: http://www.advantech.com/support

This manual is for the PCE-3132.

Part No. 2002313201 Edition 2Printed in China May 2009

PCE-3132 User Manual ii

Packing List Before you begin installing your card, please make sure that the following materialshave been shipped:
If any of these items are missing or damaged, contact your distributor or sales repre-sentative immediately. Optional Accessories

Additional Information and Assistance 1. Visit the Advantech website at www.advantech.com where you can find the lat-

est information about the product. 2. Contact your distributor, sales representative, or Advantech's customer service

center for technical support if you need additional assistance. Please have the following information ready before you call: Product name and serial number Description of your peripheral attachments Description of your software (operating system, version, application soft-

ware, etc.) A complete description of the problem The exact wording of any error messages

1 x PCE-3132 series half-sized single board computer 1 x Startup manual1 x CD for utility, drivers, and manual (in PDF format)1 x Y cable for PS/2 Keyboard, PS/2 Mouse p/n: 17000602021 x 4 ports USB cable (2.0 mm) p/n: 17000088871 x Parallel Port Cable (2.0 mm) p/n: 1700002223 2 x Serial ATA HDD data cable p/n: 1700003194 2 x Serial ATA HDD power cable p/n: 1703150102 1 x 2port COM cable kit p/n: 1700008762Jumper pack p/n: 9689000002CPU Cooler p/n: 1750000348

2 port COM cable kit p/n: 1700008762HD Audio card p/n: PCE-AUDIO-HDA1E

iii PCE-3132 User Manual

Declaration of Conformity

FCC

This device complies with the requirements in part 15 of the FCC rules: Operation issubject to the following two conditions: 1. This device may not cause harmful interference 2. This device must accept any interference received, including interference that

may cause undesired operation This equipment has been tested and found to comply with the limits for a Class A dig-ital device, pursuant to Part 15 of the FCC Rules. These limits are designed to pro-vide reasonable protection against harmful interference when the equipment isoperated in a commercial environment. This equipment generates, uses, and canradiate radio frequency energy and, if not installed and used in accordance with theinstruction manual, may cause harmful interference to radio communications. Opera-tion of this device in a residential area is likely to cause harmful interference in whichcase the user will be required to correct the interference at his/her own expense. Theuser is advised that any equipment changes or modifications not expressly approvedby the party responsible for compliance would void the compliance to FCC regula-tions and therefore, the user's authority to operate the equipment.

Caution! There is a danger of a new battery exploding if it is incorrectly installed. Do not attempt to recharge, force open, or heat the battery. Replace the battery only with the same or equivalent type recommended by the man-ufacturer. Discard used batteries according to the manufacturer’s instructions.

PCE-3132 Comparison Table

Model CPU LANPCE-3132VG-00A1E Socket 478 Intel 82574L x 1PCE-3132G2-00A1E Socket 478 Intel 82574L x 2

PCE-3132 User Manual iv

Brand Size Speed Type ECC Vendor PN

Advantech PN

Memory CPU type

Apacer 512 MB DDRII 533

DDR2 SODIMM

N - - Apacer BZZ AM4B5716FQ JS 5D 0627C

Core® Solo Intel® Cele-ron® M 530 1.73 GHZ

1 GB DDRII 667

DDR2 SODIMM

N 78.02G63.423

96SD2-1G667NN-AP

ELPIDA TWN E5108AGBG-6E-E 0706M90PB


2 GB DDRII 800

DDR2 SODIMM

N 78.A2G75.425

96SD2-2G800NN-AP

ELPIDA TWN E1108ACBG-8E-E

Core® DUO T2400 1.83 GHZ

1 GB DDRII 800

DDR2 SODIMM

N 78.02G75.422

96SD2-1G800NN-AP

ELPIDA TWN E1108ACBG-8E-E


512 MB DDRII 800

DDR2 SODIMM

N 78.92G69.442

96SD2-512M800N-AP

V59C1512804QCF25


2 GB DDRII 667

DDR2 SODIMM

N 78.A2G72.425

96SD2-2G667NN-AP1

ELPIDA JPN E1108ACSE-6E-E


1 GB DDRII 667

DDR2 SODIMM

N 78.02G72.422

96SD2-1G667NN-AP1

ELPIDA JPN E1108ACSE-6E-E


512 MB DDRII 667

DDR2 SODIMM

N 78.92G63.422

96SD2-512M667NN-AP

ELPIDA E5108AJBG-6E-E


1 GB DDRII 533

DDR2 SODIMM

N 78.02G71.422

96SD2-1G533NN-AP

ELPIDA TWN E1108ACSE-6E-E


512 MB DDRII 533

DDR2 SODIMM

N 78.92G51.442

96SD2-512M533NN-AP

V59C1512804QCF3


KingTi-ger

512 MB DDRII 533

DDR2 SODIMM

N - - ELPIDA TWN E5116AF-5C-E


King-ston

256 MB DDRII 533

DDR2 SODIMM

N KVR533 - M 6KD22 D9GKN Core® Solo Intel® Cele-ron® M 440 1.86 GHZ

512 MB DDRII 533

DDR2 SODIMM

N KVR533 - Hynix KOR HY5PS12821B FP-C4 626A


512 MB DDRII 667

DDR2 SODIMM

N KVR667 - Kingston S80751 0703 S03 D6408TEBGGL3U


2 GB DDRII 667

DDR2 SODIMM

N KVR667D2S5/2G

- Hynix KOR HY5PS1G831C FP-Y5 805A

Core®2 Duo Mobile T7400 2.16 GHZ

Tran-scend

512 MB DDRII 533

DDR2 SODIMM

N - - SEC 652 ZCD5 K4T51083QE


1 GB DDRII 533

DDR2 SODIMM

N - - JetRam J12Q3AB-6 T0629F TAX697-C93G

Core®2 Duo Mobile T7400 2.16 GHZ

1 GB DDRII 800

DDR2 SODIMM

N - - hynix KOR HY5PS12821E FP-S5 723A TS128MSQ64V8J

Core® Solo T1300 1.66 GHZ

2 GB DDRII 667

DDR2 SODIMM

N - 96SD2-2G667NN-TR

TS128MSQ64V8J Core® DUO T2500 2.00 GHZ

v PCE-3132 User Manual

PCE-3132 User Manual vi

ContentsChapter 1 General Information ............................1
1.1 Introduction ............................................................................................... 21.2 Features .................................................................................................... 21.3 Specifications ............................................................................................ 3

1.3.1 Standard SBC Functions .............................................................. 31.3.2 Display Interface ........................................................................... 31.3.3 Solid State disk ............................................................................. 31.3.4 Ethernet interface.......................................................................... 31.3.5 Mechanical and Environmental..................................................... 3

1.4 Board layout: dimensions.......................................................................... 4Figure 1.1 Board Layout: Dimensions (Component Side) ........... 4Figure 1.2 Board Layout: Dimensions (Solder Side) ................... 5

Chapter 2 Installation............................................72.1 Jumpers .................................................................................................... 8

Table 2.1: Jumpers...................................................................... 82.2 Connectors................................................................................................ 8

Table 2.2: Connectors ................................................................. 82.3 Locating Connectors (component side) .................................................... 9

Figure 2.1 Jumper & Connector Locations .................................. 92.4 Locating Connectors (solder side) .......................................................... 10

Figure 2.2 Connectors (Component Side) ................................. 102.5 Setting Jumpers ...................................................................................... 11

2.5.1 LVDS Panel Power Select (JLVDS1).......................................... 12Table 2.3: LVDS Panel Power Select........................................ 12

2.5.2 Clear CMOS (JCMOS1).............................................................. 12Table 2.4: Clear CMOS ............................................................. 12

2.5.3 COM2 RS-232/422/485 Select (JSETCOM1)............................. 13Table 2.5: COM2 RS232/422/485 Jumper setting..................... 13

2.6 Installing SODIMMs ................................................................................ 132.7 Printer port Connector (LPT1)................................................................. 142.8 CompactFlash Socket ............................................................................. 14

2.8.1 CompactFlash (CF1)................................................................... 142.9 Serial ATA Interface (SATA0, SATA1).................................................... 14

2.10 VGA/LVDS interface connections ........................................................... 142.10.1 CRT display Connector (VGA1).................................................. 142.10.2 LVDS LCD panel Connector (LVDS1) ........................................ 142.10.3 LCD Inverter Connector (INV1)................................................... 14

2.11 USB Connectors (USB12, USB34) ......................................................... 152.12 Ethernet configuration ............................................................................. 15

2.12.1 LAN Connector (LAN/LAN12) ..................................................... 152.12.2 Network boot............................................................................... 15

2.13 HDD LED/Reset/Power Button (FP1) ..................................................... 152.13.1 HDD LED (Pin 1&Pin 2) .............................................................. 152.13.2 POWER LED (Pin3 & Pin4) ........................................................ 152.13.3 Suspend led (PIN 5&Pin 6) ......................................................... 152.13.4 Reset (Pin7&Pin8) ...................................................................... 162.13.5 Power Button (Pin9&Pin10) ........................................................ 16

2.14 COM port Connector (COM12, COM34)................................................. 162.15 MINI Keyboard Connector (KBMS1) ....................................................... 162.16 External Keyboard Connector (KBMS2) ................................................. 162.17 Audio Interface Connector (HDAUD1) .................................................... 162.18 CPU FAN connector (CPUFAN1) ........................................................... 16

vii PCE-3132 User Manual

2.19 System FAN connector (SYSFAN1) ....................................................... 16

Chapter 3 BIOS Operation ................................. 173.1 BIOS Introduction.................................................................................... 183.2 BIOS Setup ............................................................................................. 18

3.2.1 Main Menu.................................................................................. 193.2.2 Standard CMOS Features .......................................................... 203.2.3 Advanced BIOS Features ........................................................... 213.2.4 Advanced Chipset Features ....................................................... 233.2.5 Integrated Peripherals ................................................................ 253.2.6 Power Management Setup ......................................................... 273.2.7 PnP/PCI Configurations.............................................................. 293.2.8 PC Health Status ........................................................................ 303.2.9 Frequency/Voltage Control ......................................................... 313.2.10 Load SetUp Defaults................................................................... 323.2.11 Set Password.............................................................................. 323.2.12 Save & Exit Setup....................................................................... 343.2.13 Quit Without Saving .................................................................... 34

Chapter 4 Driver Installation.............................. 354.1 Driver Introduction................................................................................... 364.2 Driver Installation .................................................................................... 36

4.2.1 Step 1- Install Intel INF Update Driver for Windows Vista/XP/200036

4.2.2 Step 2- Install Intel Graphic Driver for Windows Vista/XP/ 2000 364.2.3 Step 3- Install Intel Ethernet Driver for Windows Vista/XP/2000 364.2.4 Step 4-Install RAID Driver for Windows Vista/XP/2000 .............. 36

Appendix A Watchdog Timer................................ 37A.1 Programming the Watchdog Timer ......................................................... 38

A.1.1 Watchdog timer overview ........................................................... 38A.1.2 Jumper selection......................................................................... 38A.1.3 Programming the Watchdog Timer............................................. 38

Table A.1: Watchdog Timer Registers....................................... 40A.1.4 Example Program....................................................................... 41

Appendix B Pin Assignments............................... 45B.1 Connectors.............................................................................................. 46

B.1.1 HDD LED/Reset/Power Button (FP1) ......................................... 46Table B.1: HDD LED/Reset/Power Button (FP1)....................... 46

B.1.2 Printer Port Connector (LPT1) .................................................... 46Table B.2: Printer Port Connector (LPT1).................................. 46

B.1.3 LCD Inverter Connector (INV1) .................................................. 46Table B.3: LCD Inverter Connector (INV1) ................................ 46

B.1.4 Audio Interface (HDAUD1) ......................................................... 47Table B.4: Audio Interface (HDAUD1) ....................................... 47

B.1.5 LVDS Connector (LVDS1) .......................................................... 47Table B.5: LVDS Connector (LVDS1)........................................ 47

B.1.6 USB port 1, 2 Connector (USB12).............................................. 47Table B.6: USB port 1,2 Connector (USB12) ............................ 47

B.1.7 D-SUB VGA Connector (VGA1) ................................................. 48Table B.7: D-SUB VGA Connector (VGA1) ............................... 48

B.1.8 USB port 3,4 Connector (USB34)............................................... 48

PCE-3132 User Manual viii

Table B.8: USB port 3,4 Connector (USB34)............................. 48B.1.9 LAN RJ45 Connector (LAN1/LAN12).......................................... 48

Table B.9: LAN RJ45 Connector (LAN1) ................................... 48Table B.10:LAN RJ45 Connector (LAN12) ................................. 49

B.1.10 COM12 Connector ...................................................................... 49Table B.11:COM12 Connector.................................................... 49

B.1.11 COM34 Connector ...................................................................... 50Table B.12:COM34 Connector.................................................... 50

B.1.12 KB/MS Connector (KBMS1)........................................................ 50Table B.13:KB/MS Connector (KBMS1) ..................................... 50

B.1.13 External KB/mouse Connector (KBMS2) .................................... 50Table B.14:External KB/mouse Connector (KBMS2).................. 50

B.1.14 CF Connector (CF1) ................................................................... 50B.1.15 CPU FAN connector(CPUFAN1) ................................................ 50

Table B.15:+12 V FAN connector (CPUFAN1)........................... 50B.1.16 System FAN connector (SYSFAN1) ........................................... 51

Table B.16:System FAN connector (SYSFAN1)......................... 51B.1.17 GPIO Pin header (GPIO1) .......................................................... 51

Table B.17:GPIO Pin header (GPIO1)........................................ 51B.1.18 LPC Debug port (LPC1).............................................................. 51

Table B.18:LPC Debug port (LPC1) ........................................... 51B.1.19 Serial ATA0 (SATA1), Serial ATA1 (SATA2) .............................. 51

Table B.19:Serial ATA0(SATA1)................................................. 51Table B.20:Serial ATA1(SATA2)................................................. 52

B.2 Jumpers .................................................................................................. 52B.2.1 LVDS Voltage Choose (JLVDS1) ............................................... 52

Table B.21:LVDS Voltage Choose (JLVDS1) ............................. 52B.2.2 Clear CMOS (JCMOS1).............................................................. 52

Table B.22:CLEAR CMOS (JCMOS1)........................................ 52B.2.3 COM2 232/422/485 (JSETCOM1) .............................................. 52

Table B.23:COM2 232/422/485 (JSETCOM1)............................ 52

Appendix C System Assignments ........................53C.1 System I/O Ports ..................................................................................... 54

Table C.1: System I/O Ports ...................................................... 54C.2 1st MB Memory Map ............................................................................... 54

Table C.2: 1st MB Memory Map ................................................ 54C.3 DMA Channel Assignments .................................................................... 55

Table C.3: DMA Channel Assignments...................................... 55C.4 Interrupt Assignments ............................................................................. 55

Table C.4: Interrupt Assignments............................................... 55

ix PCE-3132 User Manual

PCE-3132 User Manual x

Chapter 1
1 General InformationThis chapter gives background information on the PCE-3132. Sections include:
Introduction Features Specifications Board layout and dimensions

1.1 Introduction The PCE-3132 series is a half-sized CPU card designed with powerful Intel Core 2Duo/Core Duo/Celeron M processor, with Intel 945GME and ICH7M-DH chipset,which supports Dynamic Video Memory Technology. For maximum performance,PCE-3132 also supports two 200 Pin SODIMM sockets and DDR2 memory up to 4GB. These chipsets provide an optimized on-board integrated graphics solution. Other onboard features include 1 LPT, 4 USB 2.0, 4 COM Ports (3 x RS232 and 1 xRS232/422/485), PS/2 KeyBoard/ mouse, watchdog. The SSD solution supportsType I/II CompactFlash cards. This product uses a integrated Intel 945GME graphics that supports VGA/LVDS inter-face, 2 channel (36/48-bit) LVDS LCD panel. PCE-3132 supports AC97 audio withthe addition of the optional PCA-AUDIO-HDA1E audio module. The Ethernet interface supports 10/100/1000 Mbps Intel82574L.

1.2 Features Intel Core 2 Duo/Core Duo, and Intel Celeron M processors on 65 nmFanless operation at 0 ~ 60° C On-board PCI VGA/LVDS display Supports Giga Ethernet on board Supports 4 x USB 2.0 ports Supports 2 Channel 36/48-bit LVDS for LCD Supports 533/667 MHZ Front Side Bus Supports Dual channel DDR2 400/533/667 MHz, up to 4 GB

PCE-3132 User Manual 2

Chapter 1

GeneralInform

ation

1.3 Specifications

1.3.1 Standard SBC Functions CPU: Supports Intel. Embedded Core 2 Duo/Core Duo/Celeron M processor, up to 2.16 GHZSystem chipsets: Intel 945GME+ICH7M-DHBIOS: Award 8 Mbit Flash BIOS System memory: 2 x 200 pin SODIMM sockets, support Dual channel DDR2 400/533/667 MHz, up to 4 GB 2nd cache memory: Core 2 Duo 2 M / 4 M, Core Duo 2M, Celeron M 1 MCOM Ports: Four COM ports: COM1.3.4: RS232; COM2: RS232/422/485Printer Ports: One printer port, supports SPP/EPP/ECP Keyboard/Mouse Connector: Supports standard PC/AT Keyboard and a PS/2 Mouse Power Management: Supports Power Saving Mode, including Normal/ Stan-dard/Suspend modes. APM 1.2 compliant. ACPI 1.0b, 2.0 support. Sleep State: S1.S3.S4.S5Watchdog Timer: 0 ~ 255 Sec. System resetBattery: Lithium 3V/196 mAH USB: 4 USB ports, USB 2.0 compliant

1.3.2 Display Interface Chipset: Integrated Intel 945GME GraphicsMemory size: Up to 224 MB of dynamic video memory allocationLVDS Interface: Supports 2 channel (36/48-bit) LVDS LCD Panel Display modes: – CRT Modes: 400 MHz integrated 24-bit RAMDAC; up to 2048 x 1536 at 75

MHz– LCD Modes: Up to UXGA 1600 x 1200 (Dual channel 36/48-bit TFT panel)

1.3.3 Solid State disk Supports CompactFlash Card Type I/II

1.3.4 Ethernet interface Chipset: Intel 82574L 10/100/1000 Mbps LAN ChipConnection: on-board RJ-45 connector

1.3.5 Mechanical and Environmental Dimensions (L x W): 167.64 mm x 126.39 mm (6.6" x 4.98")Power Supply Voltage: +3.3 V, +5 V, +12 VPower Consumption:– Max:

5.19 A @ 3.3 V, 4.5 A @ 12 V– Typical:

2.12 A @ 3.3 V (W/Core 2 Duo 2.16 GHZ + 2G RAM);1.36 A @ 12 V (W/Core 2 Duo 2.16 GHZ+2 G RAM)

Operating temperature: 0 ~ 60° C (32 ~ 140° F) operation Operating humidity: 0% ~ 90% Relative Humidity, non-condensing

3 PCE-3132 User Manual

1.4 Board layout: dimensions

Figure 1.1 Board Layout: Dimensions (Component Side)


Chapter 1

GeneralInform

ation

Figure 1.2 Board Layout: Dimensions (Solder Side)



Chapter 2
2 Installation This chapter explains the setup procedures of PCE-3132 hard-ware, including instructions on setting jumpers and connecting peripherals, switches and indica-tors. Be sure to read all safety pre-cautions before you begin the installation procedure.

2.1 Jumpers The PCE-3132 has a number of jumpers that allow you to configure your system tosuit your application. The table below lists the functions of the various jumpers.

2.2 Connectors Onboard connectors link the PCE-3132 to external devices such as hard disk drives,a keyboard, or floppy drives. The table below lists the function of each of the board’sconnectors.

Table 2.1: Jumpers Label Function JCMOS1 Clear CMOSJLVDS1 LVDS Panel power selectionJSETCOM1 Serial port:RS232/RS422/RS485

Table 2.2: ConnectorsLabel FunctionCF1 CF ConnectorCOM12 COM Port 1(RS232)

COM Port 2(RS232/422/485)COM34 COM Port 3.4 (RS232)CPUFAN1 CPU FAN ConnectorFP1 Front PanelGPIO1 GPIO Pin headerHDAUD1 Audio ConnectorJCASE1 Case Open ConnectorJWDT1 Watchdog timer output selectionKBMS1 PS2 Keyboard/Mouse connectorKBMS2 Pin header keyboard/mouse connector LAN1 LAN1 ConnectorLAN12 Due LAN Connector (G2 Version)LPC1 LPC Debug portLVDS1 LVDS ConnectorLPT1 Print port ConnectorSATA1 Serial ATA0SATA2 Serial ATA1SYSFAN1 System FAN ConnectorUSB12 USB Port 1.2 Pin HeaderUSB34 USB Port 3.4 Pin HeaderVGA1 CRT ConnectorINV1 LVDS inverter


Chapter 2

Installation

2.3 Locating Connectors (component side)

Figure 2.1 Jumper & Connector Locations


2.4 Locating Connectors (solder side)

Figure 2.2 Connectors (Component Side)


Chapter 2

Installation

2.5 Setting Jumpers You may configure your card to match the needs of your application by setting jump-ers. A jumper is a metal bridge used to close an electric circuit. It consists of twometal pins and a small metal clip (often protected by a plastic cover) that slides overthe pins to connect them. To “close” a jumper, you connect the pins with the clip. To“open” a jumper, you remove the clip. Sometimes a jumper will have three pins,labeled 1, 2 and 3. In this case you would connect either pins 1 and 2, or 2 and 3.

The jumper settings are schematically depicted in this manual as follows:

A pair of needle-nose pliers may be helpful when working with jumpers. If you haveany doubts about the best hardware configuration for your application, contact yourlocal distributor or sales representative before you make any changes. Generally, yousimply need a standard cable to make most connections.

closed 2-3closedopen

1 2 1 2

closed 2-3closedopen


2.5.1 LVDS Panel Power Select (JLVDS1)

2.5.2 Clear CMOS (JCMOS1)

Table 2.3: LVDS Panel Power SelectPin Function 1-2 (default) +3.3 V 2-3 +5 V

1 2 3 1 2 3

Warning! To avoid damaging the computer, always turn off the power supply before setting "Clear CMOS". Before turning on the power supply, set the jumper back to "3.0 V Battery On".This jumper is used to erase CMOS data and reset system BIOS information.The procedure for clearing CMOS is:1. Turn off the system.2. Short pin 2 and pin 3.3. Turn on the system. The BIOS is now reset to its default setting.

Table 2.4: Clear CMOS Pin Function 1-2 (default) Normal 2-3 Clear CMOS

1 2 3 1 2 3


Chapter 2

Installation

2.5.3 COM2 RS-232/422/485 Select (JSETCOM1)

2.6 Installing SODIMMs

1. The procedure for installing SODIMMs appears below. Please follow these steps carefully.

2. Make sure that all power supplies to the system are switched off 3. Install the SODIMM card. Install the SODIMM so that its gold pins point down

into the SODIMM socket. 4. Slip the SODIMM into the socket at a 45 degree angle and carefully fit the bot-

tom of the card against the connectors. 5. Gently push the SODIMM into a perpendicular position until the clips on the

ends of the SODIMM sockets snap into place. 6. Check to ensure that the SODIMM is correctly seated and all connector contacts

touch. The SODIMM should not move around in its socket.

Table 2.5: COM2 RS232/422/485 Jumper settingPin Function(5-6)(7-9)(8-10)(13-15)(14-16) RS232(3-4)(9-11)(10-12)(15-17)(16-18) RS422(1-2)(9-11)(10-12)(15-17)(16-18) RS485

Note! The modules can only fit into a socket one way. The gold pins must point down into the SODIMM socket.


2.7 Printer port Connector (LPT1) Normally, the printer port is used to connect the card to a printer. The PCE-3132includes a multi-mode (SPP/EPP/ECP) printer port accessed via CN4 and a 26-pinflat-cable connector. You will need an adapter cable if you use a traditional DB-25connector. The adapter cable has a 26-pin connector on one end, and a DB-25 con-nector on the other.

2.8 CompactFlash Socket The PCE-3132 provides a 50-pin socket for CompactFlash card type I/II.

2.8.1 CompactFlash (CF1) The CompactFlash card occupies a secondary IDE channel which can be enabled/disabled via the BIOS settings.

2.9 Serial ATA Interface (SATA0, SATA1)The PCE-3132 features a high performance serial ATA interface (up to 300 MB/s)which eases cabling to hard drives with thin and long cables.

2.10 VGA/LVDS interface connections The PCE-3132’s display interface can drive conventional CRT displays and is capa-ble of driving a wide range of LVDS flat panel displays as well. The board has two dis-play connectors: one for standard CRT VGA monitors, and one for LVDS flat paneldisplays.

2.10.1 CRT display Connector (VGA1) VGA1 is a standard 15-pin D-SUB connector used for conventional CRT displays.Users can drive a standard progressive scan analog monitor with pixel resolution upto 2048 x 1536 @ 75 Hz. Pin assignments for CRT display connector VGA1 aredetailed in Appendix B.

2.10.2 LVDS LCD panel Connector (LVDS1) PCE-3132 uses the Intel 945GME to supports single or dual-channel LVDS panelsup to UXGA panel resolution with frequency range from 25 MHz to 112 MHz. The display mode can be 2 channels (2 x 18/24 bits) LVDS LCD panel displays Userscan connect to either an 18, 24 bits LVDS LCD with LVDS1.

2.10.3 LCD Inverter Connector (INV1) The LCD inverter is connected to INV1 via a 5-pin connector to provide +5 V/+12 Vpower to the LCD display.


Chapter 2

Installation

2.11 USB Connectors (USB12, USB34) The PCE-3132 board provides up to four USB (Universal Serial Bus) ports. Thisgives complete Plug and Play, and hot attach/detach for up to 127 external devices.The USB interfaces comply with USB specification Rev. 2.0, and are fuse protected. The USB interface is accessed through the 5 x 2-pin flat-cable connector, USB1, 2,USB3, 4. You will need an adapter cable if you use a standard USB connector. Theadapter cable has a 5 x 2-pin connector on one end and a USB connector on theother. The USB interfaces can be disabled in the system BIOS setup.

2.12 Ethernet configurationThe PCE-3132 is equipped with a high performance PCI-e Ethernet interface whichprovides a complete CSMA/CD function, supporting IEEE 802.3(10 Mb/s), 802.3u(100 Mb/s), 802.3z, and 802.3ab (1000 Mb/s) implementations. It is supported by allmajor network operating systems.The PCE-3132 supports 10/100/1000Base-T Ethernet connections with onboard RJ-45 connectors (LAN12).

2.12.1 LAN Connector (LAN/LAN12)10/100Base-T or 1000Base-T connects to the PCE-3132 via a cable to a standardRJ-45 connector.

2.12.2 Network boot The Network Boot feature can be utilized by incorporating the Boot ROM image filesfor the appropriate network operating system. The Boot ROM BIOS files are includedin the system BIOS.

2.13 HDD LED/Reset/Power Button (FP1) Next, you may want to install external switches to monitor and control the PCE-3132.These features are optional: install them only if you need them. FP1 is an 2 x 5 pinheader, 180 degree, male. It provides connections for reset and power & hard diskindicator.

2.13.1 HDD LED (Pin 1&Pin 2) The HDD LED indicator for hard disk access is an active low signal (24 mA sink rate).

2.13.2 POWER LED (Pin3 & Pin4)+5 V POWER LED indicator would light when the power is on.

2.13.3 Suspend led (PIN 5&Pin 6)Suspend led indicator would light when the computer is suspend.S0:always lightS1/S3: fast flashS4/S5: slow flash


2.13.4 Reset (Pin7&Pin8)If you install a reset switch, it should be an open single pole switch.Momentarily pressing the switch will activate a reset. The switch shouldbe rated for 10 mA, 5 V.

2.13.5 Power Button (Pin9&Pin10)PCE-3132 also supports power on/off button.

2.14 COM port Connector (COM12, COM34) The PCE-3132 provides four COM ports (COM1, 3, 4: RS-232 and COM2: RS-232/422/485). And JSETCOM1 is for COM RS-232/422/485 selection. It provides con-nections for serial devices (a mouse, etc.) or a communication network. You can findthe pin assignments for the COM port connector in Appendix B.

2.15 MINI Keyboard Connector (KBMS1) The PCE-3132 board provides a keyboard connector that supports both a keyboardand a PS/2 style mouse. In most cases, especially in embedded applications, a key-board is not used. If the keyboard is not present, the standard PC/AT BIOS will report an error or failduring power-on self-test (POST) after a reset. The PCE-3132’s BIOS standard setupmenu allows you to select "All, but Keyboard" under the "Halt On"selection. Thisallows no-keyboard operation in embedded system applications, without the systemhalting under POST.

2.16 External Keyboard Connector (KBMS2) In addition to the Mini keyboard connector on the PCE-3132’s rear plate, there is anadditional onboard external keyboard connector, allowing for greater flexibility in sys-tem design.

2.17 Audio Interface Connector (HDAUD1) The Audio Interface link is a 10 pin connector, the PCE-3132 can support Audio withthe addition of optional PCE-AUDIO-HDA1E. Detailed pin assignment refer toAppendix B.

2.18 CPU FAN connector (CPUFAN1)The PCE-3132 is equipped with a 3-pin FAN connector providing +12 V power forCPU FAN.

2.19 System FAN connector (SYSFAN1)The PCE-3132 is equipped with a 3-pin FAN connector providing +12 V power forsystem FAN.


Chapter 3
3 BIOS OperationThis chapter describes how to set BIOS configuration data.Sections include:
BIOS Introduction BIOS Setup

3.1 BIOS IntroductionAwardBIOS 6.0 is a full-featured BIOS provided by Advantech to deliver superior per-formance, compatibility, and functionality to industrial PCs and embedded boards. Itsmany options and extensions let you customize your products to a wide range ofdesigns and target markets.The modular, adaptable AwardBIOS 6.0 supports the broadest range of third-partyperipherals and all popular chipsets, plus Intel, AMD, nVidia, VIA, and compatibleCPUs from 386 through Pentium, AMD Geode, K7 and K8 (including multiple proces-sor platforms), and VIA Eden C3 and C7 CPUs.You can use Advantech’s utilities to select and install features that suit your needsand your customers’ needs.

3.2 BIOS SetupThe PCE-3132 system has AwardBIOS 6.0 built-in, which includes a CMOS SETUPutility that allows users to configure settings as required or to activate certain systemfeatures.The CMOS SETUP saves configuration settings in the CMOS RAM of the mother-board. When the system power is turned off, the onboard battery supplies the neces-sary power to the CMOS RAM so that settings are retained.To access the CMOS SETUP screen, press the <Del> button during the power-onBIOS POST (Power-On Self Test).

Control Keys

< ↑ >< ↓ >< ← >< → > Move to select item.<Enter> Select Item.<Esc> Main Menu - Quit and not save changes into CMOS.

Sub Menu - Exit current page and return to Main Menu.Page Up/+> Increase the numeric value or make changes.<Page Down/-> Decrease the numeric value or make changes.<F1> General help, for Setup Sub Menu.<F2> Item Help.<F5> Load Previous Values.<F7> Load Optimized Default.<F10> Save all CMOS changes.


Chapter 3

BIO

S O

peration

3.2.1 Main MenuPress the <Del> key during startup to enter the BIOS CMOS Setup Utility; the MainMenu will appear on the screen. Use arrow keys to highlight the desired item, andpress <Enter> to accept, or enter the sub-menu.

Standard CMOS FeaturesThis setup page includes all the features for standard CMOS configuration.Advanced BIOS FeaturesThis setup page includes all the features for advanced BIOS configuration.Advanced Chipset FeaturesThis setup page includes all the features for advanced chipset configuration.Integrated PeripheralsThis setup page includes all onboard peripheral devices.Power Management SetupThis setup page includes all the power management items.PnP/PCI Configurations This setup page includes PnP OS and PCI device configuration.PC Health StatusThis setup page includes the system auto-detect CPU and system temperature,voltage, and fan speed.Frequency/Voltage ControlThis setup page includes CPU host clock control, frequency ratio and voltage.Load SetUp DefaultsThis selection loads setup values for the system performance configuration.Set PasswordEstablish, change or disable passwords. Save & Exit SetupSave CMOS value settings to CMOS and exit BIOS setup.Exit Without SavingAbandon all CMOS value changes and exit BIOS setup.


3.2.2 Standard CMOS Features

DateThe date format is <weekday>, <month>, <day>, <year>.Weekday From Sun to Sat, determined and displayed by BIOS onlyMonth From Jan to DecDay From 1 to 31 Year From 1999 through 2098TimeThe time format is <hours> : <minutes> : <seconds>, based on 24-hour time.IDE Channel 0 Master/SlaveIDE HDD Auto-Detection - Press "Enter" for automatic device detection.IDE Channel 1 Master/SlaveIDE HDD Auto-Detection - Press "Enter" for automatic device detection.Halt onThis item determines whether the computer will stop if an error is detected dur-ing power up.No Errors The system boot process will not stop for any errorAll Errors Whenever the BIOS detects a non-fatal error the system

boot process will be stopped.All, But Keyboard The system boot process will not stop for a keyboard error,

but will stop for all other errors. (Default value)All, But Diskette The system boot process will not stop for a diskette error,

but will stop for all other errors.All, But Disk/Key The system boot process will not stop for a keyboard or

disk error, but will stop for all other errors.Base MemoryDisplays the amount of base (or conventional) memory installed in the system.Extended MemoryDisplays the amount of extended memory (above 1 MB in CPU°Øs memoryaddress map) installed in the system.Total MemoryDisplays the total system memory size.


Chapter 3

BIO

S O

peration

3.2.3 Advanced BIOS Features

CPU FeatureThis item allows the user to adjust CPU settings such as CPU ratio, VID andThermal, and special features like XD flag.Removable Device PriorityThis item allows the user to select the boot sequence for removable devices.Hard Disk Boot PriorityThis item allows the user to select the boot sequence for system devices suchas HDD, SCSI, and RAID. CPU L1 & L2 CacheThis item allows the user to enable/disable CPU L1/L2 cache.CPU L3 Cache [Enabled]This item allows the user to enable/disable CPU L3 cache. Hyper-Threading Technology [Enabled]This item allows the user to enable/disable Hyper-threading support for theIntel® Pentium® 4 processor with HT Technology.Quick Power On Self Test [Enabled]This field speeds up the Power-On Self Test (POST) routine by skipping re-test-ing a second, third and fourth time. The default setting is enabled.First / Second / Third / Other Boot DriveHard Disk Sets boot priority for the hard diskRemovable Sets boot priority for the removable deviceCDROM Sets boot priority for CDROMLegacy LAN Sets boot priority for LANDisabled Disables this boot functionBoot Up NumLock Status [Enabled]This item allows the user to activate the Number Lock key at system boot.Gate A20 Option [Fast]This item allows the user to switch on or off A20 control by port 92.


Typematic Rate SettingThis item allows the user to set the two typematic control items.This field controls the speed of – Typematic Rate (Chars/Sec)

This item controls the speed at which the system registers auto repeated key-strokes. The eight settings are: 6, 8, 10, 12, 15, 20, 24 and 30.

– Typematic Delay (Msec)This item sets the key press delay time before auto repeat begins. The fourdelay rate options are: 250, 500, 750 and 1000.

Security Option [Setup]System System requires correct password before booting, and also

before permitting access to the Setup page.Setup System will boot, but requires correct password before

permitting access to Setup. (Default value)APIC Mode [Enabled]This item allows the user to enable/disable the “Advanced Programmable Inter-rupt Controller”. APIC is implemented in the motherboard and must be sup-ported by the operating system; it extends the number of IRQs available.MPS Version Control for OS [1.4]This item sets the operating system multiprocessor support version.


Chapter 3

BIO

S O

peration

3.2.4 Advanced Chipset Features

DRAM Timing Selectable [By SPD]This item allows the user to set optimal timings for items 2 through 5. The sys-tem default setting of “By SPD” follows the SPD information on the ROM chipand ensures the system runs stably, with optimal performance.CAS Latency Time [Auto]This item allows the user to set the timing delay in clock cycles before SDRAMstarts a read command after receiving it. DRAM RAS# to CAS# Delay [Auto]This item allows the user to set the timing of the transition from RAS (rowaddress strobe) to CAS (column address strobe) as both rows and columns areseparately addressed shortly after the DRAM is refreshed.DRAM RAS# Precharge [Auto]This item allows the user to set the DRAM RAS# precharge timing. The systemdefault is set to “Auto” to reference the data from the SPD ROM. Precharge delay (tRAS) [Auto]This item allows the user to adjust memory precharge time.System Memory Frequency [Auto]This item allows the user to adjust memory frequency to improve performance.System BIOS Cacheable [Enabled]This item allows the system BIOS to be cached to allow faster execution andbetter performance.Video BIOS Cacheable [Disabled]This item allows the video BIOS to be cached to allow faster execution and bet-ter performance.

Note! The "Advanced Chipset Features" screen controls the configuration of the board's chipset register settings and performance tuning - the options on this screen may vary depending on the chipset type. It is strongly recommended that only technical users make changes to the default settings.


Memory Hole At 15 M-16 M [Disabled]This item reserves 15 - 16 MB of memory address space for ISA expansioncards that specifically require the setting. Memory from 15 - 16 MB will beunavailable to the system because only the expansion cards can access mem-ory in this area.PEG/Onboard VGA Control [Auto]This item allows the user to select the onboard graphics processor or the PCIExpress card.PEG Force X1 [Disabled]This item allows the user to convert a PCI Express X16 slot to PCI Express X1slot.On-Chip Frame Buffer Size [8 MB]This item allows the user to adjust the memory buffer for on-chip graphics.DVMT Mode [DVMT]This item allows the user to adjust Intel's Dynamic Video Memory Technology(DVMT). The BIOS provides three options to choose from (DVMT, FIXED andBoth).DVMT/FIXED Memory Size [128 MB]This item allows the user to adjust DVMT/FIXED graphics memory size.Boot Display [Auto]This item allows the user to decide which display mode to use for the boot dis-play.Panel Type [None]This item allows the user to adjust panel resolution.ADD2 Card [None]This item allows the user to adjust the type of ADD2 card.Init Display First [PCI Slot]This item is for setting start up video output from the PCI or onboard device.


Chapter 3

BIO

S O

peration

3.2.5 Integrated Peripherals

OnChip IDE Device This item enables users to set the OnChip IDE device status, including IDEdevices and setting PIO and DMA access modes. Some chipsets supportnewer SATA devices (Serial-ATA).Onboard Device This item enables users to set the Onboard Device status, including USB,AC97, MC97 and LAN devices.

Note! The "Integrated Peripherals" screen controls chipset configuration for IDE, ATA, SATA, USB, AC97, MC97 and Super IO and Sensor devices. The options on this screen vary depending on the chipset.


Super IO Device This item enables users to set the Super IO device status, including Floppy,COM, LPT and IR.Onboard Serial port 1 [3F8/IRQ4]This item allows the user to adjust serial port 1 IO address and IRQ.Onboard Serial port 2 [2F8/IRQ3]This item allows the user to adjust serial port 2 IO address and IRQ.Onboard Serial port 3 [3E8]This item allows the user to adjust serial port 3 IO address.Serial Port 3 Use IRQ [IRQ6]This item allows the user to adjust serial port 3 IRQ.Onboard Serial port 4 [2E8]This item allows the user to adjust serial port 4 IO address.Serial Port 3 Use IRQ [IRQ10]This item allows the user to adjust serial port 4 IRQ.Onboard Parallel Port [378/IRQ7]This item allows the user to adjust parallel port IO address and IRQ.Parallel Port Mode [ECP+EPP1.9]This item allows the user to adjust parallel port mode.ECP Mode Use DMA [3]This item allows the user to adjust the ECP DMA resource.


Chapter 3

BIO

S O

peration

3.2.6 Power Management Setup

PCI Express PM Function [Press Enter]This item allows the user to set PCI Express’s PME function to disabled orenabled.ACPI Function [Enabled]This item defines the ACPI (Advanced Configuration and Power Management)feature that makes hardware status information available to the operating sys-tem, and communicates to PC and system devices for improved power man-agement.ACPI Suspend Type [S3 (STR)]This item allows the user to select the sleep state when the computer is in sus-pend mode. S1(POS) Suspend mode is equivalent to a software power down;S3(STR) The system shuts down with the exception of a refresh of

electrical current to system memory.Power Management [Min Saving]This item allows the user to select the system power saving mode.Min Saving - Minimum power management. Suspend Mode=1 hr.Max Saving - Maximum power management. Suspend Mode=1 min.User Defined - Allows the user to set each mode individually. Suspend Mode=Disabled, or 1 min ~ 1 hr.

Note! The "Power Management Setup" screen allows configuration of the sys-tem for effective energy savings while still operating in a manner consis-tent with intended computer use.


Video Off Method [DPMS]This item allows the user to determine the manner is which the monitor isblanked.V/H SYNC+Blank This option will cause the system to turn off vertical and

horizontal synchronization ports and write blanks to the video buffer.

Blank Screen This option only writes blanks to the video buffer.DPMS Initial display power management signaling. Video Off In Suspend [Yes]This item allows the user to turn off the video when the system enters suspendmode.Suspend Type [Stop Grant]This item allows the user to determine the suspend type.Suspend Mode [Disabled]This item allows the user to determine the length of time of system inactivityafter which all devices except the CPU will be shut down.HDD Power Down Mode [Disabled]This item allows the user to determine the system inactivity time, when the harddisk drive will be powered down.Soft-Off by PWR-BTTN [Instant-Off]This item allows the user to define the power button functions.Instant-Off Press the power button to power off instantly.Delay 4 Sec Press and hold the power button for 4 sec to power off. CPU THRM-Throttling [50.0%]This item allows the user to set CPU THRM-Throttling duty cycle.PowerOn By LAN [Disabled]This item allows the user to power on the system by LAN. The choices are“Enable” and “Disable”.PowerOn By Modem [Disabled]This item allows the user to power on the system by Modem. The choices are“Enable” and “Disable”.USB KB Wake-Up From S3 [Disabled]This item allows user to set USB keyboard wake up system from S3. Thechoices are Enable or Disable.PowerOn By Alarm [Disabled] The choices are “Enabled” and “Disabled”.


Chapter 3

BIO

S O

peration

3.2.7 PnP/PCI Configurations

Reset Configuration Data [Disabled]This item allows the user to clear any PnP configuration data stored in theBIOS.Resources Controlled By [Auto (ESCD)]IRQ Resources This item allows you respectively assign an interrupt type

for IRQ-3, 4, 5, 7, 9, 10, 11, 12, 14, and 15.DMA Resources This item allows you respectively assign an interrupt type

for DMA-0, 1, 2, 3, 4, 5, 6, and 7.PCI VGA Palette Snoop [Disabled]The item is designed to solve problems caused by some non-standard VGAcards. A built-in VGA system does not need this function.Maximum Payload Size [4096]This item allows the user to adjust maximum TLP (Transaction Layer Packet)payload size.

Note! The "PnP/PCI Configurations" screen sets up the IRQ and DMA (both PnP and PCI bus assignments).


3.2.8 PC Health Status

Case Open Warning [Disabled]Enable this to detect if the case is open or closed.CPU Warning Temperature [Disabled]This item will prevent the CPU from overheating. Current System TemperatureThis shows you the current temperature of the system.Current CPU TemperatureThis shows the current CPU temperature.VCORE and Other VoltagesThis shows the voltage of VCORE, +12 V, AVCC, +5 V, +3.3 V, VBAT.Shutdown Temperature [Disabled]The system will shut down automatically when the CPU temperature is over theselected setting. This function can prevent CPU damage caused by overheat-ing.

Note! The "PC Health Status" screen controls the thermal, fan, and voltage status of the board. The options on this page vary depending on the chipset.


Chapter 3

BIO

S O

peration

3.2.9 Frequency/Voltage Control

Auto Detect PCI Clk [Enabled]This item enables users to set the PCI Clk either by automatic system detectionor manually.Spread Spectrum [Disabled]This item enables users to set the spread spectrum modulation.

Note! The "Frequency/Voltage Control" screen controls the CPU host and PCI frequency. The options on this page vary depending on the chipset; items show up according to installed CPU capacities.


3.2.10 Load SetUp Defaults

3.2.11 Set Password

Note! "Load SetUp Defaults" loads the default system values directly from ROM. If the stored record created by the setup program should ever become corrupted (and therefore unusable), select Load Setup Defaults to have these default values load automatically for the next bootup.

Note! To enable this feature, you should first go to the "Advanced BIOS Fea-tures" menu, choose the Security Option, and select either System or Setup, depending on which aspects you want password protected. Sys-tem requires a password both to boot the system and to enter Setup. Setup requires a password only to enter Setup. A password may be at most 8 characters long.


Chapter 3

BIO

S O

peration

To Establish Password1. Choose the Set Password option from the CMOS Setup Utility Main Menu and

press <Enter>.2. When you see Enter Password, enter the desired password and press <Enter>.3. At the Confirm Password prompt, retype the desired password, then press

<Enter>.4. Select Save to CMOS and exit, type <Y>, then <Enter>.

To Change Password1. Choose the Set Password option from the CMOS Setup Utility main menu and

press <Enter>.2. When you see Enter Password, enter the existing password and press <Enter>.3. You will see the Confirm Password prompt, type it in again, and press <Enter>.4. Select Set Password again, and at the Enter Password prompt, enter the new

password and press <Enter>.5. At the Confirm Password prompt, retype the new password, and press <Enter>.6. Select Save to CMOS and exit, type <Y>, then <Enter>.

To Disable a Password1. Choose the Set Password option from the CMOS Setup Utility main menu and

press <Enter>.2. When you see the Enter Password prompt, enter the existing password and

press <Enter>.3. You will see Confirm Password, type it in again, and press <Enter>.4. Select Set Password again, and at the Enter Password prompt, DO NOT enter

anything - just press <Enter>.5. At the Confirm Password prompt, again, DO NOT type in anything - just press

<Enter>.6. Select Save to CMOS and exit, type <Y>, then <Enter>.


3.2.12 Save & Exit Setup

3.2.13 Quit Without Saving

Note! Typing <Y> will quit the BIOS Setup Utility and save the user setup val-ues to CMOS.Typing <N> will return to BIOS Setup.

Note! Typing <Y> will quit the BIOS Setup Utility without saving any changes to CMOS.Typing <N> will return to the BIOS Setup Utility.


Chapter 4
4 Driver InstallationThis chapter gives you the driver installation information on the PCE-3132 Half-size CPU card.Sections include:
Driver IntroductionDriver Installation

4.1 Driver Introduction The CD shipped with PCE-3132 should contain the drivers below; please follow thissequence to complete the driver installation. 1. Install Intel INF Update Driver for Windows Vista/XP/2000. 2. Install Intel Graphic Driver for Windows Vista/XP/2000. 3. Install Intel 82574L Ethernet Driver for Windows Vista/XP/2000. 4. Install RAID driver for Window Vista/XP/2000.

http://www.microsoft.com/whdc/system/bus/USB/USB2support.mspx

4.2 Driver Installation Insert the PCE-3132 CD into the CD-ROM device, and follow below installation pro-cess from Step 1 to Step 4.

4.2.1 Step 1- Install Intel INF Update Driver for Windows Vista/XP/2000 1. Click on the “Chipset” folder and double click the “*.exe” file. 2. Follow the instructions that the driver installation wizard shows. 3. The system will help you to complete the driver installation.

4.2.2 Step 2- Install Intel Graphic Driver for Windows Vista/XP/ 2000 1. Click on the “VGA” folder and double click the “*.exe” file. 2. Follow the instructions that the driver installation wizard shows. 3. The system will help you to complete the driver installation.

4.2.3 Step 3- Install Intel Ethernet Driver for Windows Vista/XP/20001. Click on the “LAN” folder and double click the “*.exe” file. 2. Follow the instructions that the driver installation wizard shows. 3. The system will help you to complete the driver installation.

4.2.4 Step 4-Install RAID Driver for Windows Vista/XP/20001. Click on the “RAID” folder and double click the “*.exe” file.2. Follow the instructions that the driver installation wizard shows.3. The system will help you to complete the driver installation.

Note! For Windows XP Embedded, Windows CE 5.0 and Linux support, please contact sales representative or technical person. Note: Down-loading the update for Windows XP or Windows 2000 may be required for enabling USB 2.0 function. Details information please refers to below web link.


Appendix A
A Watchdog Timer The board is equipped with a watchdog timer that resets the CPU if processing comes to a standstill for any reason. This fea-ture ensures system reliability in industrial standalone or unmanned environments.

A.1 Programming the Watchdog TimerThe PCE-3132's watchdog timer can be used to monitor system software operationand take corrective action if the software fails to function within the programmedperiod. This section describes the operation of the watchdog timer and how to pro-gram it.

A.1.1 Watchdog timer overviewThe watchdog timer is built in to the super I/O controller W83627UHG. It provides thefollowing functions for user programming:

Can be enabled and disabled by user's programTimer can be set from 1 to 255 seconds or 1 to 255 minutesGenerates reset signal if the software fails to reset the timer before time-out

A.1.2 Jumper selectionThe JWDT1 jumper is used to select reset in the event the watchdog timer is tripped.See Chapter 1 for detailed jumper settings.

A.1.3 Programming the Watchdog TimerThe I/O port address of the watchdog timer is 2E (hex) and 2F (hex). 2E (hex) is theaddress port. 2F (hex) is the data port. You must first assign the address of registerby writing an address value into address port 2E (hex), then write/ read data to/fromthe assigned register through data port 2F (hex).


Appendix A

Watchdog

Timer


Table A.1: Watchdog Timer RegistersAddress of Register (2E) Attribute

Read/Write Value (2F) & description

87 (hex) -Write this address to I/O address port 2E (hex) twice to unlock the W83627UHG.

07 (hex) write Write 08 (hex) to select register of watchdog timer.

30 (hex) writeWrite 01 (hex) to enable the function of the watchdog timer. Disable is set as default.

F5 (hex) write Set seconds or minutes as units for the timer.

Write 0 to bit 3: set second as counting unit. [default]Write 1 to bit 3: set min-utes as counting unit

F6 (hex) write

0: stop timer [default]01 ~ FF (hex) : The amount of the count, in seconds or minutes, depends on the value set in register F5 (hex). This number decides how long the watchdog timer waits for strobe before generating an interrupt or reset signal. Writing a new value to this register can reset the timer to count with the new value.

F7 (hex) read/write

Bit 6: Write 1 to enable keyboard to reset the timer, 0 to disable. [default]Bit 5: Write 1 to generate a timeout signal immediately and automatically return to 0. [default]Bit 4: Read status of watchdog timer, 1 means timer is “timeout“.

AA (hex) - Write this address to I/O port 2E (hex) to lock the watchdog timer 2.


Appendix A

Watchdog

Timer

A.1.4 Example Program1. Enable watchdog timer and set 10 sec. as timeout interval;-----------------------------------------------------------Mov dx,2eh ; Unlock W83627UHGMov al,87hOut dx,alOut dx,al;-----------------------------------------------------------Mov al,07h ; Select registers of watchdog timerOut dx,alInc dxMov al,08hOut dx,al;-----------------------------------------------------------Dec dx ; Enable the function of watchdog timerMov al,30hOut dx,alInc dxMov al,01hOut dx,al;-----------------------------------------------------------Dec dx ; Set second as counting unitMov al,0f5hOut dx,alInc dxIn al,dxAnd al,not 08hOut dx,al;-----------------------------------------------------------Dec dx ; Set timeout interval as 10 seconds and start countingMov al,0f6hOut dx,alInc dxMov al,10Out dx,al;-----------------------------------------------------------Dec dx ; lock W83627UHGMov al,0aahOut dx,al2. Enable watchdog timer and set 5 minutes as timeout interval;-----------------------------------------------------------Mov dx,2eh ; unlock W83627UHGMov al,87hOut dx,alOut dx,al


;-----------------------------------------------------------Mov al,07h ; Select registers of watchdog timerOut dx,alInc dxMov al,08hOut dx,al;-----------------------------------------------------------Dec dx ; Enable the function of watchdog timerMov al,30hOut dx,alInc dxMov al,01hOut dx,al;-----------------------------------------------------------Dec dx ; Set minute as counting unitMov al,0f5hOut dx,alInc dxIn al,dxOr al,08hOut dx,al;-----------------------------------------------------------Dec dx ; Set timeout interval as 5 minutes and start countingMov al,0f6hOut dx,alInc dxMov al,5Out dx,al;-----------------------------------------------------------Dec dx ; lock W83627UHGMov al,0aahOut dx,al3. Enable watchdog timer to be reset by mouse;-----------------------------------------------------------Mov dx,2eh ; unlock W83627UHGMov al,87hOut dx,alOut dx,al;-----------------------------------------------------------Mov al,07h ; Select registers of watchdog timerOut dx,alInc dxMov al,08hOut dx,al;-----------------------------------------------------------


Appendix A

Watchdog

Timer

Dec dx ; Enable the function of watchdog timerMov al,30hOut dx,alInc dxMov al,01hOut dx,al;-----------------------------------------------------------Dec dx ; Enable watchdog timer to be reset by mouseMov al,0f7hOut dx,alInc dxIn al,dxOr al,80hOut dx,al;-----------------------------------------------------------Dec dx ; lock W83627UHGMov al,0aahOut dx,al4. Enable watchdog timer to be reset by keyboard;-----------------------------------------------------------Mov dx,2eh ; unlock W83627UHGMov al,87hOut dx,alOut dx,al;-----------------------------------------------------------Mov al,07h ; Select registers of watchdog timerOut dx,alInc dxMov al,08hOut dx,al;-----------------------------------------------------------Dec dx ; Enable the function of watchdog timerMov al,30hOut dx,alInc dxMov al,01hOut dx,al;-----------------------------------------------------------Dec dx ; Enable watchdog timer to be strobed reset by keyboardMov al,0f7hOut dx,alInc dxIn al,dxOr al,40hOut dx,al


;-----------------------------------------------------------Dec dx ; lock W83627UHGMov al,0aahOut dx,al5. Generate a time-out signal without timer counting;-----------------------------------------------------------Mov dx,2eh ; unlock W83627UHGMov al,87hOut dx,alOut dx,al;-----------------------------------------------------------Mov al,07h ; Select registers of watchdog timerOut dx,alInc dxMov al,08hOut dx,al;-----------------------------------------------------------Dec dx ; Enable the function of watchdog timerMov al,30hOut dx,alInc dxMov al,01hOut dx,al;-----------------------------------------------------------Dec dx ; Generate a time-out signalMov al,0f7hOut dx,al ;Write 1 to bit 5 of F7 registerInc dxIn al,dxOr al,20hOut dx,al;-----------------------------------------------------------Dec dx ; lock W83627UHGMov al,0aahOut dx,al


Appendix B
B Pin AssignmentsThis appendix contains informa-tion of a detailed or specialized nature.

B.1 Connectors

B.1.1 HDD LED/Reset/Power Button (FP1)

B.1.2 Printer Port Connector (LPT1)

B.1.3 LCD Inverter Connector (INV1)

Table B.1: HDD LED/Reset/Power Button (FP1) Pin Signal Pin Signal 1 HDLED_A 2 HDLED3 LED_POWER 4 GND 5 LED_SB 6 SUSLED7 FP_RESET 8 GND 9 PANSWIN# 10 GND

Table B.2: Printer Port Connector (LPT1)Pin Signal Pin Signal1 PIO_STB 2 LPT_#AFD3 PIO_PD0 4 LPT_#ERR5 PIO_PD1 6 LPT_#INIT7 PIO_PD2 8 LPT_#SLIN9 PIO_PD3 10 GND11 PIO_PD4 12 GND13 PIO_PD5 14 GND15 PIO_PD6 16 GND17 PIO_PD7 18 GND19 LPT_#ACK 20 GND21 LPT_BUSY 22 GND23 LPT_PE 24 GND25 LPT_SLCT 26 NC

Table B.3: LCD Inverter Connector (INV1)Pin Signal Pin Signal1 VCC12_INV1 2 GND3 LVDS_BKLTEN 4 V8R5 VP3_P5


Appendix B

Pin A

ssignments

B.1.4 Audio Interface (HDAUD1)

B.1.5 LVDS Connector (LVDS1)

B.1.6 USB port 1, 2 Connector (USB12)

Table B.4: Audio Interface (HDAUD1)Pin Signal Pin Signal1 AC_5V 2 GND3 AC_SYNC 4 AC_BITCLK5 AC_SDOUT 6 AC_SDIN07 AC_SDIN1 8 #AC_RST9 AC_12V 10 GND11 GND

Table B.5: LVDS Connector (LVDS1)Pin Signal Pin Signal1 VDD_FP 2 VDD_FP3 GND 4 GND5 VDD_FP 6 VDD_FP7 LVDS_A_D0N 8 LVDS_B_D0N9 LVDS_A_D0P 10 LVDS_B_D0P11 GND 12 GND13 LVDS_A_D1N 14 LVDS_B_D1N15 LVDS_A_D1P 16 LVDS_B_D1P17 GND 18 GND19 LVDS_A_D2N 20 LVDS_B_D2N21 LVDS_A_D2P 22 LVDS_B_D2P23 GND 24 GND25 LVDS_A_CLKN 26 LVDS_B_CLKN27 LVDS_A_CLKP 28 LVDS_B_CLKP29 GND 30 GND31 LVDS_DCLK 32 LVDS_DDAT33 GND 34 GND35 LVDS_A_D3N 36 LVDS_B_D3N37 LVDS_A_D3P 38 LVDS_B_D3P39 LVDS_BKLTEN 40 VCON

Table B.6: USB port 1,2 Connector (USB12)Pin Signal Pin Signal1 USBV3 2 USBV33 USBD4- 4 USBD5-5 USBD4+ 6 USBD5+7 GND 8 GND9 GND


B.1.7 D-SUB VGA Connector (VGA1)

B.1.8 USB port 3,4 Connector (USB34)

B.1.9 LAN RJ45 Connector (LAN1/LAN12)

Table B.7: D-SUB VGA Connector (VGA1)Pin Signal Pin Signal1 VGA_RED 2 VGA_GREEN3 VGA_BLUE 4 NC5,6,7,8, 10,16,17 GND 11 NC12 VGA_SMDAT 13 VGA_Hsync14 VGA_Vsync 15 VGA_DCLK9 VCC_VGA

Table B.8: USB port 3,4 Connector (USB34)Pin Signal Pin Signal1 USBV2 2 +5 V3 USBD2- 4 USBD3-5 USBD2+ 6 USBD3+7 GND 8 GND9 GND

Table B.9: LAN RJ45 Connector (LAN1)Pin Signal Pin Signal1 LAN1_MDI0+ 2 LAN1_MDI0-3 LAN1_MDI0- 4 LAN1_MDI1-5 LAN1_1P8R 6 TCT17 LAN1_MDI2+ 8 LAN1_MDI2-9 LAN1_MDI3+ 10 LAN1_MDI3-11 LAN1_LED1_R 12 LAN1_AUX3313 LAN1_LINK1000# 14 LAN1_LINK1000#


Appendix B

Pin A

ssignments
B.1.10COM12 Connector
Table B.10: LAN RJ45 Connector (LAN12)Pin Signal Pin SignalA1 LAN2_MDI0+ A2 LAN2_MDI0-A3 LAN2_MDI1+ A4 LAN2_MDI1-A5 LAN2_1P8R A6 TCT2A7 LAN2_MDI2+ A8 LAN2_MDI2-A9 LAN2_MDI3+ A10 LAN2_MDI3-A11 LAN2_LED1_R A12 LAN2_AUX33A13 LAN2_LINK1000# A14 LAN2_LINK100#B1 LAN1_MDI0+ B2 LAN1_MDI0-B3 LAN1_MDI1+ B4 LAN1_MDI1-B5 LAN1_1P8R B6 TCT1B7 LAN1_MDI2+ B8 LAN1_MDI2-B9 LAN1_MDI3+ B10 LAN1_MDI3-B11 LAN1_LED1_R B12 LAN1_AUX33B13 LAN1_LINK1000# B14 LAN1_LINK100#

Table B.11: COM12 ConnectorPin Signal Pin Signal1 DCDA 2 DSRA3 SINA 4 RTSA5 SOUTA 6 CTSA7 DTRA 8 RIA9 GND 10 GND11 COM2_DCD# 12 DSRB13 COM2_SIN 14 RTSB15 COM2_SOUT 16 CTSB17 COM2_DTR# 18 RIB19 GND 20 GND


B.1.11 COM34 Connector

B.1.12KB/MS Connector (KBMS1)

B.1.13External KB/mouse Connector (KBMS2)

B.1.14CF Connector (CF1)

B.1.15CPU FAN connector(CPUFAN1)

Table B.12: COM34 ConnectorPin Signal Pin Signal1 DCDC 2 DSRC3 SINC 4 RTSC5 SOUTC 6 CTSC7 DTRC 8 RIC9 GND 10 GND11 DCDD 12 DSRD13 SIND 14 RTSD15 SOUTD 16 CTSD17 DTRD 18 RID19 GND 20 GND

Table B.13: KB/MS Connector (KBMS1)Pin Signal Pin Signal1 KBDATA 2 MSDATA3 GND 4 +5V5 KBCLK 6 MSCLK

Table B.14: External KB/mouse Connector (KBMS2)Pin Signal Pin Signal1 R_MCLK 2 CN11_VCC3 GND 4 R_MDAT5 R_KDAT 6 R_KCLK

Table B.15: +12 V FAN connector (CPUFAN1)Pin Signal Pin Signal1 GND 2 CPUFANPWM_123 CPUFANIN


Appendix B

Pin A

ssignments

B.1.16System FAN connector (SYSFAN1)

B.1.17GPIO Pin header (GPIO1)

B.1.18LPC Debug port (LPC1)

B.1.19Serial ATA0 (SATA1), Serial ATA1 (SATA2)

Table B.16: System FAN connector (SYSFAN1)Pin Signal Pin Signal1 GND 2 SYSFANPWM_123 SYSFANIN

Table B.17: GPIO Pin header (GPIO1)Pin Signal Pin Signal1 GPIO_PORT80_1 2 GPIO_PORT80_53 V_GPIO 4 GND5 GPIO_PORT80_2 6 GPIO_PORT80_67 GND 8 GND9 GPIO_PORT80_3 10 GPIO_PORT80_711 GND 12 GND13 GPIO_PORT80_4 14 GPIO_PORT80_8

Table B.18: LPC Debug port (LPC1)Pin Signal Pin Signal1 CLK_33M_FWH 2 LPC_LAD13 #PLTRST 4 LPC_LAD05 #LFRAME 6 VCC37 LPC_LAD3 8 GND9 LPC_LAD2

Table B.19: Serial ATA0(SATA1)Pin Signal Pin Signal1 GND 2 SATA_TX0P3 SATA_TX0A 4 GND5 SATA_RX0P 6 SATA_RX0N7 GND


B.2 Jumpers

B.2.1 LVDS Voltage Choose (JLVDS1)

B.2.2 Clear CMOS (JCMOS1)

B.2.3 COM2 232/422/485 (JSETCOM1)

Table B.20: Serial ATA1(SATA2)Pin Signal Pin Signal1 GND 2 SATA_TX1P3 SATA_TX1N 4 GND5 SATA_RX1N 6 SATA_RX1P7 GND

Table B.21: LVDS Voltage Choose (JLVDS1)Pin Signal Pin Signal1-2 +3.3 V 2-3 +5 V

Table B.22: CLEAR CMOS (JCMOS1)Pin Signal Pin Signal1-2 Normal 2-3 Clear CMOS

Table B.23: COM2 232/422/485 (JSETCOM1)Pin Signal Pin Signal(5-6)(7-9)(8-10)(13-15)(14-16) RS232 * (3-4)(9-11)(10-12)(15-17)(16-18) RS422(1-2)(9-11)(10-12)(15-17)(16-18) RS485


Appendix C
C System AssignmentsThis appendix contains informa-tion of a detailed nature. Sections include:
System I/O ports1st MB memory mapDMA channel assignmentsInterrupt assignments

C.1 System I/O Ports

C.2 1st MB Memory Map

Table C.1: System I/O PortsAddr. range (Hex) Device00-0F Master DMA controller20-21F Master Interrupt controller40-5F Timer/Counter60-6F Keyboard controller(60h) KBC Data(61h) Misc Functions & Spkr Ctrl(64h) KBC Command/Status70-77 RTC/COMS/NMI-Disable78-7F -available for system use-80 -reserved-(debug port)81-8F DMA Page Registers90-91 -available for system use-92 System Control93-9F -available for system use-A0-A1H Slave Interrupt ControllerC0-DF Slave DMA ControllerE0-FF -available for system use-100-CF7 -available for system use-CF8-CFB PCI Configuration AddressCFC-CFF PCI Configuration DataD00-FFFF -available for system use-200-20F Game Port2F8-2FF COM23E8-3EF COM32E8-2EF COM4378-37F Printer Port (Standard & AFF)3F8-3FF COM1

Table C.2: 1st MB Memory MapAddr. range (Hex) DeviceE0000h - FFFFFh BIOSCC000h - DFFFFh UnusedC0000h - CBFFFh VGA BIOSA0000h - BFFFFh Video Memory00000h - 9FFFFh Base memory


Appendix C

System

Assignm

ents

C.3 DMA Channel Assignments

C.4 Interrupt Assignments

Table C.3: DMA Channel AssignmentsChannel Function0 Available1 Available 2 Avaiable3 Available (printer port)4 Cascade for DMA controller 15 Available6 Available7 Available

Table C.4: Interrupt AssignmentsInterrupt# Interrupt sourceIRQ 0 Interval timerIRQ 1 KeyboardIRQ 2 Interrupt from controller 2 (cascade)IRQ 3 COM2IRQ 4 COM1IRQ 5 UnusedIRQ 6 COM3IRQ 7 LPT1IRQ 8 RTCIRQ 9 ACPIIRQ 10 COM10IRQ 11 UnusedIRQ 12 PS/2 mouseIRQ 13 INT from co-processorIRQ 14 Primary IDEIRQ 15 Secondary IDE for CFC


www.advantech.comPlease verify specifications before quoting. This guide is intended for referencepurposes only.All product specifications are subject to change without notice.No part of this publication may be reproduced in any form or by any means,electronic, photocopying, recording or otherwise, without prior written permis-sion of the publisher.All brand and product names are trademarks or registered trademarks of theirrespective companies.© Advantech Co., Ltd. 2009

Date post:	30-Aug-2021
Category:	Documents
Upload:	others
View:	2 times
Download:	0 times

PCE-3132 user manual ed.2€¦ · This manual is for the PCE-3132. Part No. 2002313201 Edition 2...

Documents