Directional Control Valveshasmak.com.tr/parkervalf/Parker Pilot Operated Directional...

Directional Control ValvesCatalog HY14-2502/US

A

2502-A1.p65, dd

A30 Parker Hannifin CorporationHydraulic Valve DivisionElyria, Ohio, USA

General DescriptionSeries D1VA and D1VP directional control valves arehigh performance, 4 and 5-chamber, direct operated, airand oil pilot controlled, 3 or 4-way valves. They areavailable in 2 or 3-position and conform to NFPA’sD03, CETOP 3 mounting patterns.

Features• Low pilot pressure required – 4.1 Bar (60 PSI) minimum

• Manual overrides standard

Series D1VA, D1VPTechnical Information

DimensionsInch equivalents for millimeter dimensions are shown in (**)

Oil Operated D1VP, Single and Double Pilot

SpecificationsMounting Pattern NFPA D03, CETOP 3, NG 6

Operating: 345 Bar (5000 PSI)MaximumTank Line: D1VA 34 Bar (500 PSI)Pressure

D1VP 207 Bar (3000 PSI)Maximum Flow See Reference Data

D1VA:Air Minimum 4.1 Bar (60 PSI)

Pilot Pressure Air Maximum 10.2 Bar (150 PSI)D1VP:

Oil Minimum 15.2 Bar (220 PSI)Oil Maximum 207 Bar (3000 PSI)

Air OperatedShift Volume. The air pilot chamber requires a volume of1.8 cc (.106 in.3) for complete shift from center to end.

Pilot Piston. The pilot piston area is 506 mm2 (.785 in.2). Pilotpiston stroke is 3.4 mm (.135 in.).

Response Time. Response time will vary with pilot line size,pilot line length, pilot pressure, air control valve shift time andair valve flow capacity (Cv).

Oil OperatedShift Volume. The hydraulic pilot chamber requires a volumeof 0.7 cc (.042 in.3) for complete shift from center to end.

Pilot Piston. The hydraulic piston area is 198 mm2 (.307 in.2).Pilot piston stroke is 3.4 mm (.135 in.).

Response Time. Response time will vary with pilot line size,pilot line length, pilot pressure, pilot valve shift time and airvalve flow capacity (GPM).

AA BB

P T

AA BB

P T

Note: 22.0 mm (0.87”) from bottom of bolthole counterbore to bottom of valve.

43.0(1.70)min.

22.0(0.87)

9.0(0.35)

40.5(1.60)

0.56(0.022)

3.3 (0.13) max.X & Y Ports

51.0(2.00)min.

127.0(5.13)

42.0(1.65)

16.9(0.67)

23.0(0.91)

15.5(0.61)

50.0(1.97)

46.0(1.81)

23.8(0.94)

SeeNote

Y

SAE #4


A

2502-A1.p65, dd


NFPA D03CETOP 3

Code DescriptionN NitrileV Fluorocarbon

Code Symbol

1

2

4

8*

9**

20*

26*

30**

81

82

* 8, 20 and 26 spools haveclosed crossover.

** 9 and 30 spools have opencrossover.

OilOperator

A B

P T

A B

P T

A B

P T

A B

P T

A B

P T

A B

P T

A B

P T

Code Description Symbol

Single operator, two positionB# spring offset.

P to A and B to T in offset position.

Double operator,C three position,

spring centered.

D Double operator,two position, detent.

Two position, spring centered.E# P to B and A to T

in shifted position.

Single operator, two position,H# spring offset. P to B and A to T

in offset position.

Two position, spring centered.K# P to A and B to T


# D available with 20 and 30 spools only.B & H available with 20, 26 and 30 spools only.E & K not available with 20, 26 and 30 spools.

This condition varieswith spool code.

y xA B

P T

A B

P T

y x

A B

P T

y

xA B

P T

xA B

P T

y A B

P T

Series D1VPOrdering Information

A B

P T

A B

P T

A B

P T

Valve schematic symbols are perNFPA/ANSI standards, providingflow P to A when energizingoperator X. Note operators reversesides for #8 and #9 spools. Seeinstallation information for details.

DirectionalControl Valve

Actuator Spool Style DesignSeriesNOTE:

Not requiredwhen ordering.

SealCompound

1VBasicValve

Variations

D P

Valve Weight: 1.90 kg (4.2 lbs.)

Standard Bolt Kit: BK209 1–24x1.25

Metric Bolt Kit: BKM209 M5–0.8x30mm

Code DescriptionOmit StandardP10* Monitor Switch

4F Heavy Duty Detent

90 BSPP Threads

* Not available on C and D styles.Not CE or CSA approved.

Bold: Designates Tier I products and options.

Non-Bold: Designates Tier II products and options. These products will have longer lead times.


A

2502-A1.p65, dd


NFPA D03CETOP 3


Code Symbol

1

2

4

8*

9**

81

82

* 8 spool has closed crossover.

** 9 spool has open crossover.

Series D1VAOrdering Information

A B

P T

A B

P T

A B

P T

A B

P T

A B

P T

A B

P T

A B

P T


Single operator, two positionB spring offset.



spring centered.

D Double operator,two position, detent.

Two position, spring centered.E P to B and A to T


Single operator, two position,H spring offset. P to B and A to T

in offset position.

Two position, spring centered.K P to A and B to T



A B

P T

b a

A B

P T

b a

A B

P T

b

A B

P T

a

A B

P T

a

A B

P T

b

Valve schematic symbols are per NFPA/ANSIstandards, providing flow P to A when energizingoperator A. Note operators reverse sides for #8and #9 spools. See installation information fordetails.

DirectionalControl Valve

Actuator Spool Style DesignSeriesNOTE:


SealCompound

1VBasicValve

Variations

D


Standard Bolt Kit: BK209 1–24x1.25

Metric Bolt Kit: BKM209 M5–0.8x30mmGrade 8 bolts required

A

Code DescriptionOmit StandardP10* Monitor Switch

90 BSPP Threads

* Not available on C & Dstyles.Not CE or CSA approved.

AirOperator




A

2502-A1.p65, dd


Series D1VADimensions

Inch equivalents for millimeter dimensions are shown in (**)

Air Operated D1VA, Double Pilot

Air Operated D1VA, Single Pilot

117.8 (4.64)

104.55 (4.12)

192.5(7.58)

61.6(2.43)

51.95(2.05)

23.8(0.94)

23.0 (0.91)

38.5(1.52)

46.0(1.81)

1/8 NPT Typ.

46.0(1.81)

23.0 (0.91)

23.8(0.94)

51.95(2.05)

38.5(1.52)

156.3(6.15)

61.6(2.43)

81.5(3.21)

1/8" NPT Typ.




A

2502-A2.p65, dd


General DescriptionSeries D3A directional control valves arehigh performance, 4-chamber, direct operated, air pilotcontrolled, 3 or 4-way valves. They are available in2 or 3-position and conform to NFPA’s D05/CETOP 5mounting patterns.

Features• Low pilot pressure required – 4.1 Bar (60 PSI) minimum.

• Manual overrides standard.

• High flow, low pressure drop design.

SpecificationsMounting Pattern NFPA D05, CETOP 5, NG 10Maximum Operating: 345 Bar (5000 PSI)Pressure Tank Line: 34 Bar (500 PSI)Maximum Flow See Spool Reference ChartPilot Pressure Air Minimum 4.1 Bar (60 PSI)

Air Maximum 6.9 Bar (100 PSI)

Air OperatedShift Volume. The air pilot chamber requires a volume of1.8 cc (.106 in.3) for complete shift from center to end.

Pilot Piston. The pilot piston area is 506 mm2 (.785 in.2).Pilot piston stroke is 3.4 mm (.135 in.).

AA BB

P T

Technical Information Series D3A

Response Time* (ms)Signal to 95% spool stroke measured at172 Bar (2500 PSI) and 75 LPM (20 GPM)

Pilot Pressure Pull-In Drop-Out60 PSI 23.0 ms 23.0 ms100 PSI 19.0 ms 38.0 ms

* Chart is for reference only. Response time will vary with pilot linesize, length, air pressure and air valve flow capacity (Cv).


A

2502-A2.p65, dd


Ordering Information Series D3A

NFPA D05CETOP 5

NG 10


Code DescriptionOmit Standard

90 BSPP Pilot Port

Code Description Symbols

Single operator, two positionB # spring offset.



spring centered.

Double operator,D # two position,

detent.

Two position, spring centered.E P to B and A to T


Single operator, two position,H # spring offset. P to B and A to T

in offset position.

Two position, spring centered.K P to A and B to T


# B, D & H styles available with 20 and 30 spools only.

AirOperator

Indicates air pilot.


A B

P T

b a

A B

P T

b a

A B

P T

b

A B

P T

a

A B

P T

A B

P T

b

Valve Weight: 4.1 kg (9 lbs.)

Standard Bolt Kit: BK98

Metric Bolt Kit: BKM98

D 3Directional

Control ValveBasic Valve Actuator Spool Style Seal

CompoundVariations

ADesignSeriesNOTE:


Mounting Bolt KitsUNC Bolt Kits for use with D3A

Directional Control Valves & Manapak/CartpakNumber of Manapaks/Cartpaks

@ 2.00" (50mm) thickness

0 1 2 3D3A Standard: BK98 BK141 BK142 BK143

1.62" 3.50" 5.50" 7.50"

Metric: BKM98 BKM141 BKM142 BKM14340mm 90mm 140mm 190mm

NOTE: All bolts are SAE grade 8, 1/4-20 UNC-2A thread, torque to16 Nm (12 ft-lbs)

Valve schematic symbols are per NFPA/ANSI standards, providingflow P to A when energizing operator A. Note operators reverse sidesfor #8 and #9 spools. See installation information for details.

Code Symbol Code Symbol

1 20*

2 30†

4 81

8* 82

9†

* 8 and 20 spools have closed crossover.† 9 and 30 are open crossover.

A B

P T

A B

P T

A B

P T

A B

P T

A B

P T

A B

P T

A B

P T

A B

P T

A B

P T




A

2502-A2.p65, dd


Air Operated, Double Pilot

Air Operated, Single Pilot

Dimensions Series D3A

181.82(7.164)

89.95(3.544)

36.00(1.418)

70.00(2.758)

35.00(1.379)

79.51(3.133)

101.81(4.011)

SeeNote


Note: 30.0mm (1.18") from bottom of bolt hole counterbore to bottom of valve.


214.0(8.43)

90.0(3.55)

36.0(1.42)

35.0(1.38)

70.0(2.76)

67.1(2.64)

134.3(5.29)

121.1(4.77)

1/8 NPTF


A

2502-A3.p65, dd


ApplicationSeries D31 hydraulic directional control valves arehigh performance, solenoid controlled, pilot operated,2-stage 4-way valves. They are available in 2 or 3-position styles and are manifold mounted. Thesevalves conform to NFPA’s D05H, CETOP 5 and canalso be manufactured to an NFPA DO5HE, CETOP 5Hconfiguration.

OperationSeries D31 directional valves consist of a 5-chamberstyle main body, a case hardened sliding spool, and apilot valve or pilot operators (hydraulic or pneumatic).

Features

• Easy access mounting bolts.

• 345 Bar (5000 PSI) pressure rating.

• Flows to 175 LPM (45 GPM) depending on spool.

• Choice of four operator styles.

• Rugged four land spools.

• Low pressure drop.

• Phosphate finish.

• Both NFPA and CETOP mountingstyles available.

Series D31Introduction

D31*W Solenoid Operated Plug-In Conduit Box

D3*P Oil Pilot Operated

D31*L Lever Operated

D31*A Air Pilot Operated


A

2502-A3.p65, dd


Series D31*WTechnical Information

General DescriptionSeries D31*W directional control valves are 5-chamber,pilot operated, solenoid controlled valves. The valvesare suitable for manifold or subplate mounting.

Response TimeResponse time (milliseconds)at 345 Bar (5000 PSI) is 76 LPM (20 GPM)

Solenoid PilotType Pressure Pull-In Drop-Out

500 40 50

DC 1000 36 50

2000 34 50500 20 33

AC 1000 18 332000 13 33

Features• World design – Available worldwide.

• Mounting bolts below center line of spool – Minimizesspool binding.

• Five chamber style – Eliminates pressure spikes intubes, increasing valve life.

• High pressure and flow ratings – Increasedperformance options in a compact valve.

Switching Limit Charts

6.9 Bar (100 PSI) pilot

5000

4000

3000

2000

1000

345

276

207

138

69

0

0

GPM

LPM

10 20

15138 113

30

76

40

PSI Bar

8

9

Flow

Sup

ply

Pre

ssur

e

Note: Internal Drain1, 4 spools – 113 LPM (30 GPM) max., 2, 9 & 14 spools – per curveAll others – 95 LPM (25 GPM) max.

189

50

2,7 (14)

9 with150 PSI Pilot

For Styles F and M – external drain only(For internal drain see note below)

1, 3, (15), 4, 5 (16), 6, 11

6.9 Bar (100 PSI) pilot

0GPM

LPM

10 20

151 18938 113

30

76

40 50Flow

Note: Internal Drain1, 4 spools – 113 LPM (30 GPM) max., 7 spool – per curveAll others – 95 LPM (25 GPM) max.

5000

4000

3000

2000

1000

345

276

207

138

69

0

PSI Bar

4Sup

ply

Pre

ssur

e

23,(15)

9

118

7 (14)

1, 5, (16) 6, 20, 30

For Styles B, C, E, H and KD Style – external drain only (For internal drain see note below)

Mounting Pattern NFPA D05H, CETOP 5NFPA D05HE, CETOP 5H

Max. Operating 345 Bar (5000 PSI) StandardPressure CSA 207 Bar (3000 PSI)

Max. Tank Line Internal Drain Model:Pressure 103 Bar (1500 PSI) AC Std.

207 Bar (3000 PSI) DC Std./AC Opt.External Drain Model:207 Bar (3000 PSI)

CSA 103 Bar (1500 PSI)

Max. Drain 103 Bar (1500 PSI) AC onlyPressure 207 Bar (3000 PSI) DC Std./AC Opt.


Min. Pilot Pressure 6.9 Bar (100 PSI)

Max. Pilot Pressure 345 Bar (5000 PSI) Standard


Nominal Flow 76 Liters/Min (20 GPM)

Maximum Flow See Switching Limit Charts

Specifications


A

2502-A3.p65, dd


Ordering Information Series D31*W


Code DescriptionA** 24/50 VAC

D 120 VDC

G 198 VDC

J 24 VDCK 12 VDC

N*** 220/50 VAC

P*** 110/50 VAC

Q** 100/60 VAC

R 24/60 VAC

T 240/60 - 220/50 VACU 98 VDC

Y 120/60 - 110/50 VACZ 250 VDC


B* Single solenoid, 2 position, spring offset.P to A and B to T in offset position.

C Double solenoid, 3 position,spring centered.

D* Double solenoid, 2 position, detent.

E* Single solenoid, 2 position, spring centered.P to B and A to T when energized.

F† Single solenoid, 2 position, spring offset,energized to center. Spacer on A side.P to A and B to T in offset position.

H* Single solenoid, 2 position, spring offset.P to B and A to T in offset position.

K Single solenoid, 2 position, spring centered.P to A and B to T when energized.

M† Single solenoid, 2 position, spring offset,energized to center. Spacer on B side.P to B and A to T in offset position.

* 020 and 030 spools only.† High watt only.


001 011

002 012

003 014

004 015

005 016

006 020*

007 030**

008* 081009**

010 082

A B

P T

A B

P T

A B

P T

A B

P T

A B

P T

A B

P T

A B

P T

A B

P T

A B

P T

A B

P T

A B

P T

A B

P T

A B

P T

A B

P T

A B

P T

A B

P T

A B

P T

b

A B

P T

b a

A B

P T

b

A B

P T

b

A B

P T

b a

A B

P T

a

A B

P T

a

A B

P T

a

A B

P T

DDirectional

Control ValveBasic Valve Actuator Spool Style Seal Solenoid

Voltage

Code DescriptionW# Solenoid, Wet Pin,

Screw-inHW# Reversed Wiring

Pilot Supplyand Drain

Code Description1* Internal Pilot, External Drain2* External Pilot, External Drain4# Internal Pilot, Internal Drain5 External Pilot, Internal Drain

* F and M style available only withexternal drain.

# Not available with 002, 007, 008, 009 or014 spools.

* 008, 020 & 026 spool have closed crossover.** 009 & 030 spool have open crossover.

Code Description31D NFPA D05HE, CETOP 5H,

DIN NG10,D03 Pilot, ISO Port

31V NFPA D05H, CETOP 5,D03 Pilot, NFPA Port

A B

P T

# Valve schematic symbols are per NFPA/ANSIstandards, providing flow P to A when energizingsolenoid A. Note operators reverse sides for#008 and #009 spools. See installationinformation for details. To configure per DINstandards (A coil over A port, B coil over B port)code valves as D31VHW***.

** High watt only.*** Explosion proof only.




A

2502-A3.p65, dd


Ordering Information Series D31*W

Code DescriptionC Conduit BoxD† Metric Plug

(M12X1), DESINA

E* Explosion Proof

G Plug-inJ†* Deutsch

(DT06-2S)

M†* Metri-Pack (150)

P DIN with PlugS†* Double Spade

W* DIN without Plug

Code DescriptionOmit High Watt

D* Explosion Proof, EEXD ATEX

E* Explosion Proof, EEXME ATEX

F** Low Watt

C† CSA Hazardous Location

L*** 8 Watt

O* Explosion Proof, MSHA

U* Explosion Proof, UL/CSA

* Not available with lights.** AC only.*** DC and AC Rectified only.† Applicable to conduit box and

plug-in style only.

Valve Weight:Double Solenoid 5.4 kg (12.0 lbs.)



SolenoidConnection

TubeOptions

Approvals DesignSeriesNOTE:


ManualOverrideOptions


P* Extended with Boot

T* No Override

W* Waterproof Protection

* Manual override options notavailable on explosion proofvalves.

Code DescriptionOmit Low Pressure, AC only

103.5 Bar (1500 PSI)H High Pressure, AC only

207 Bar (3000 PSI)G Standard Pressure, DC/AC

Rectified 207 Bar (3000 PSI)

CoilOptions

ElectricalOptions

Code DescriptionOmit No Options

J* Diode Surge Suppressor

B† Rectified Coil

* DC only; not applicable withDIN plug with lights.

† DC tube standard.

ShiftResponse

and Indication

* Not available with lights.† DC only.

Code DescriptionOmit Standard Valve3*† CSA USA (UL 429)

4* CSA Canada

* Not available with AC highpressure tube.

† B, C, H styles only.J, K, Y, U voltages only.C, G, W sol. connections only.

ValveVariations

See next page forValve Variations

Code DescriptionOmit Standard ResponseI3* Monitor Switch Direct Op. End Stroke

I6* Monitor Switch Direct Op. Start Stroke

* Not available on F or M styles. Spools 8, 9, 81& 82 not available.

Not CE or CSA approved.

Mounting Bolt KitsUNC Bolt Kits for use with D31*W

Directional Control Valves & Manapak/CartpakNumber of Manapaks/Cartpaks

@ 2.00" (50mm) thickness

0 1 2 3D31*W Standard: BK98 BK141 BK142 BK143

1.62" 3.50" 5.50" 7.50"

Metric: BKM98 BKM141 BKM142 BKM14340mm 90mm 140mm 190mm

NOTE: All bolts are SAE grade 8. Standard bolts are 1/4-20 UNCA thread.Metric bolts are M6-1.0 thread. Torque to 16 Nm (12 ft-lbs).




A

2502-A3.p65, dd


Ordering Information

Valve Variations

Series D31*W

Code Description D31*W D61*W D81*W D101*W

5 Signal Lights

6 Manaplug – Brad Harrison Mini

56 Manaplug (Mini) with Lights

7A Manaplug – Brad Harrison (12x1) Micro

7B Manaplug (Micro) with Lights (D1 only)

20 Fast Response

1A Manaplug (Mini) Single Sol. 5-pin

1B Manaplug (Micro) Single Sol. 5-pin

1C Manaplug (Mini) Single Sol. 5-pin, with Lights

1D Manaplug (Micro) Single Sol. 5-pin, with Lights

1E Manaplug (Mini) Single Sol. 5-pin,with Stroke Adjust “A” & “B” End

1F Manaplug (Micro) Single Sol. 5-pin,with Stroke Adjust “A” & “B” End

1G Manaplug (Mini) Single Sol. 5-pin,with Stroke Adjust “A” & “B” End and Lights

1H Manaplug (Micro) Single Sol. 5-pin,with Stroke Adjust “A” & “B” End and Lights

1M Manaplug Opposite of Normal

1P Painted Body

3A Pilot Choke Meter Out

3B Pilot Choke Meter In

3C Pilot Pressure Reducer

3D Stroke Adjust “B” End

3E Stroke Adjust “A” End

3F Stroke Adjust “A” & “B” End

3G Pilot Choke Meter Out with Lights

3H Pilot Choke Meter In with Lights

3J Pilot Pressure Reducer with Lights

3K Pilot Choke Meter Outwith Stroke Adjust “A” & “B” End

3L Pilot Choke Meter Out, Stroke Adjust “A” & “B” Endwith Lights and Manaplug (Mini)

3M Pilot Choke Meter Out, Pilot Pressure Reducer,Stroke Adjust “A” & “B” End

3R Pilot Choke Meter Out and Pilot Pressure Reducer

3S Pilot Choke Meter Outwith Lights and Manaplug (Mini)

3W Manaplug (Mini) 5-pinwith Stroke Adjust “A” & “B” End and Lights

4B Protection Cap for Monitor Switch

4D* Twist & Lock Override (Old 5426)

4E* Push Manual Override (Old x5450)

gray = available; white= not available

*DC/AC rectified only. Not available with explosion proof.


A

2502-A3.p65, dd


Series D31*WTechnical Information

Solenoid RatingsInsulation System Class F

Allowable Deviation -10% to +15% for DC and AC rectified coilsfrom rated voltage -5% to +5% for AC Coils

Armature Wet pin type

CSA File Number LR60407

Environmental DC Solenoids meet NEMA 4 and IP67Capability when properly wired and installed. Contact

HVD for AC coil applications.

Explosion Proof Solenoid Ratings*UL & CSA (EU) Class I, Div 1 & 2, Groups C & D

Class II, Div 1 & 2, Groups E, F & GAs defined by the NEC

MSHA (EO) Complies with 30CFR, Part 18

ATEX (ED) Complies with ATEX requirements for:Exd, Group IIB; EN50014: 1999+ Amds.1 & 2, EN50018: 2000

CSA Hazardous Location Class II, Div 1 & 2, Groups E, F & G

* Allowable Voltage Deviation ±10%.Note that Explosion Proof AC coils are single frequency only.

VoltageCode

PowerCode

VoltageIn

Rush Amps Amperage

In Rush Amps D31VW VA

@ 3MM

HoldingAmps

D31VW

WattsD31VW

ResistanceD31VW

A 24/50 VAC, High Watt 7.00 Amps 168 VA 2.65 Amps 28 W 1.67 ohmsD L 120 VDC N/A N/A 0.09 Amps 10 W 1584.00 ohms

N/A N/A 0.26 Amps 30 W 528.00 ohmsG L 198 VDC N/A N/A 0.05 Amps 10 W 3920.40 ohms

N/A N/A 0.15 Amps 30 W 1306.80 ohmsJ L 24 VDC N/A N/A 0.44 Amps 10 W 51.89 ohms

N/A N/A 1.32 Amps 30 W 17.27 ohmsK L 12 VDC N/A N/A 0.88 Amps 10 W 12.97 ohms

N/A N/A 2.64 Amps 30 W 4.32 ohmsL L 6 VDC N/A N/A 1.67 Amps 10 W 3.59 ohms

N/A N/A 5.00 Amps 30 W 1.20 ohmsQ 100 VAC / 60 Hz 1.7 Apms 170 VA 0.56 Amps 24 W 26.0 ohms

QD 100 VAC / 60 Hz 0.41 Amps 135 VA 0.41 Amps 18 W 31.2 ohmsQD 100 VAC / 50 Hz 0.57 Amps 150 VA 0.57 Amps 24 W 31.2 ohmsR 24/60 VAC, High Watt 8.00 Amps 192 VA 2.70 Amps 27 W 1.40 ohms

F 24/60 VAC, Low Watt 6.67 Amps 160 VA 2.20 Amps 23 W 1.52 ohmsT 240/60 VAC, High Watt 0.77 Amps 185 VA 0.26 Amps 25 W 134.50 ohms

220/50 VAC, High Watt 0.82 Amps 180 VA 0.31 Amps 27 W 134.50 ohmsF 240/60 VAC, Low Watt 0.70 Amps 168 VA 0.22 Amps 21 W 145.00 ohmsF 220/50 VAC, Low Watt 0.75 Amps 165 VA 0.26 Amps 23 W 145.00 ohms

U L 98 VDC N/A N/A 0.10 Amps 10 W 960.00 ohmsY 120/60 VAC, High Watt 1.55 Amps 186 VA 0.49 Amps 25 W 33.70 ohms

110/50 VAC, High Watt 1.65 Amps 182 VA 0.58 Amps 27 W 33.70 ohmsF 120/60 VAC, Low Watt 1.40 Amps 168 VA 0.42 Amps 21 W 36.50 ohmsF 110/50 VAC, Low Watt 1.50 Amps 165 VA 0.50 Amps 23 W 36.50 ohms

Z L 250 VDC N/A N/A 0.04 Amps 10 W 6875.00 ohmsN/A N/A 0.13 Amps 30 W 1889.64 ohms

R 24/60 VAC 7.63 Amps 183 VA 2.85 Amps 27 W 1.99 ohmsT 240/60 VAC 0.76 Amps 183 VA 0.29 Amps 27 W 1.34 ohmsN 220/50 VAC 0.77 Amps 169 VA 0.31 Amps 27 W 1.38 ohmsY 120/60 VAC 1.60 Amps 192 VA 0.58 Amps 27 W 33.50 ohmsP 110/50 VAC 1.47 Amps 162 VA 0.57 Amps 27 W 34.70 ohmsQ 100/60 VAC 1.90 Amps 192 VA 0.70 Amps 27 W 38.60 ohmsK 12 VDC N/A N/A 2.75 Amps 33 W 4.36 ohmsJ 24 VDC N/A N/A 1.38 Amps 33 W 17.33 ohmsD 120 VDC N/A N/A 0.28 Amps 33 W 420.92 ohmsZ 250 VDC N/A N/A 0.13 Amps 33 W 1952.66 ohms

Explosion Proof Solenoids

Code


A

2502-A3.p65, dd


Technical Information Series D31*W

D31*W Series Pressure Drop vs. FlowThe chart below provides the flow vs. pressure dropcurve reference for the D31VW Series valves by spooltype.

Example:Find the pressure drop at 76 LPM (20 GPM) for aD31VW with a number 1 spool. To the right of spoolnumber 1, locate the number 3 in the P-A column, and2 in the B-T column.

Using the graph at the bottom, locate curves 2 and 3and read the pressure drop values. Total pressuredrop through the valve is the sum of the two values.

Note: Pressure drops should be checked for all flow paths,especially when using non-symmetrical spools 003, 005, 007, 014,015 and 016) and unbalanced actuators.

D31*W Pressure Drop Reference ChartCurve Number

Spool Shifted Center ConditionNo. P-A P-B B-T A-T (P-T) (B-A) (A-B) (P-A) (P-B) (A-T) (B-T)

001 3 3 2 1 - - - - - - -

002 3 3 1 1 3 3 3 4 4 1 1

003 3 3 1 1 - - - - - 3 -

004 3 3 1 1 - - - - - 1 1

005 3 3 1 1 - - - 5 - - -

006 3 3 1 1 - 5 7 6 5 - -

007 4 2 1 1 4 - - - 3 - 2

009 3 3 1 1 7 - - - - - -

010 3 2 - - - - - - - - -

011 3 2 1 1 - - - - - 8 8

014 2 4 1 1 4 - - 4 - 2 -

015 3 2 4 1 - - - - - - 4

016 5 2 1 1 - - - - 5 - -

020 5 4 2 2 - - - - - -

030 4 3 1 1 - - - - - -

Pressure Drop Chart

8

7

6

1

2

5

4

3

400

300

200

100

28

21

14

7

10 20

151113

30 40

38 760

0

GPM

LPM

PSI Bar

Pre

ssu

re D

rop

(

P)

�

Flow

Viscosity Correction Factor

Viscosity 75 150 200 250 300 350 400(SSU)% of ΔP 93 111 119 126 132 137 141(Approx.) Curves were generated using 110 SSU hydraulic oil. For any other viscosity, pressure drop will change per chart.


A

2502-A3.p65, dd


Dimensions Series D31*W

Conduit Box, Double AC Solenoid

Conduit Box and Stroke Adjust, Double AC Solenoid

210.7(8.30)

58.4(2.30)

5.2 (0.20)Adjustment

109.1(4.30)

109.2(4.30)

43.0 (1.69)Min. CoilRemoval

Stroke Adjust"B" Port EndVariations 3D

Stroke Adjust"A" Port EndVariations 3E

Note: 30.0mm (1.18") from bottomof bolt hole counterbore to bottomof valve.


210.7(8.30)

105.3(4.15)

58.4(2.30)

105.3(4.15)

105.4(4.15)

49.6(1.95)21.8

(0.86)3.0(0.12)

½ NPTF Thd.Both Ends

36.0(1.42)

83.0(3.27)

106.8(4.21)

149.0(5.87)

70.0(2.76)

35.0(1.38)

SeeNote

ManualOverride


Ref



A

2502-A3.p65, dd


Conduit Box and Pilot Choke Control, Double AC Solenoid

Series D31*WDimensions


Conduit Box, Single AC Solenoid

105.3(4.15)

163.7(6.45)

58.4(2.30)

218.8(8.62)

39.6(1.56)

Pilot ChokeControl

Variation 3A & 3B3A – Metering Out3B – Metering In




A

2502-A3.p65, dd


Hirschmann and Stroke Adjust, Double DC Solenoid



244.4(9.63)

94.0(3.70)

109.14.30

109.24.30

5.2(0.20)

Stroke Adjust“B” Port EndVariation 3D

Variation 3F(as shown)

Stroke Adjust"A" and "B" End

Stroke Adjust“A” Port EndVariation 3E

Adjustment

54.0(2.13)

Min. coilremoval


Hirschmann and Pilot Choke Control, Double DC Solenoid

Pilot ChokeControl

Variation 3A & 3B

244.4(9.63)

200.0(7.88)

94.0(3.70)

39.6(1.56)

185.0(7.29)

3A - Metering Out3B - Metering In



A

2502-A3.p65, dd




Explosion Proof U.L. and C.S.A. Approved, Double Solenoid

ATEX, Single Solenoid

70.0(2.76)

35.0(1.38)

36.0(1.42)

83.0(3.27)

125.8(4.96)

177.4(6.99)

163.7(6.45)

81.8(3.22)

62.0(2.44)

152.1(5.99)

304.4(11.99)

1/2”NPT

18 Inch Lead WiresStandard

(2.90)73.5

162.5(6.40)

130.5(5.14)

74.7(2.94)

69.9(2.75)

M20x1.5-6H Thd.

Ground Studwith Lock Washer

34.9(1.38)

183.9(7.25)

125.8(4.96)

214.7(8.46)

83.0(3.27)

36.0(1.42) 35.0

(1.38)70.0

(2.76)

62.0(2.44)

224.4(8.84)

(2.90)73.5


A

2502-A3.p65, dd



Plug-in Conduit Box Double DC Solenoid

Plug-in Conduit Box, Single DC Solenoid

244.4(9.63) Ref.

120.6(4.75)

66.4(2.61)

54.0 (2.13) Min.Coil Removal 1/2 NPTF Thd.

Both Ends

352.4(13.89)

160.5(6.32)

106.8(4.21)

83.0(3.27)

36.0(1.42)

35.0(1.38) 70.0

(2.76)

ManualOverride

24.8(0.98)

49.6(1.95)

122.2(4.81)

122.2(4.81)

188.5(7.43)

66.3(2.61)

122.2(4.81)


A

2502-A3.p65, dd


Plug-in Conduit Box, Double DC Solenoidwith Variation I3 (Monitor Switch)


Monitor Switch(valve variation I3 and I6)

This feature provides for electrical confirmation ofthe spool shift. This can be used in safety circuits, toassure proper sequencing, etc.

Switch DataPin 1 and Pin 3 have outputs equal to the input.When the monitor switch has the output to Pin 1,Pin 3 will have an output of zero, and vice-versa.When the valve is switched, Pin 1 and Pin 3 willswitch outputs.

Series D31*WDimensions

Double Solenoid. With solenoid “A” energized, flow path is P→Aand B→T. When solenoid “B” is energized, flow path is P→B andA→T. The center condition on a spring-centered valve exists whenboth coils are de-energized, or during a complete shift, as thespool passes through center.

Position Control Switch

Sensor / DriverCircuitry

PIN 2Input18-42 VDC

PIN 1

PIN 3

Outputs

Load 0.2 A Max

39.7(1.56) 244.4 (9.63) Ref.

122.2 (4.81)

66.4 (2.61)

94.5(3.72)

159.8(6.29)

120.6(4.75)

122.2(4.81)

36.0(1.42)

35.0(1.38)

70.0(2.76)

83.0(3.27)

ManualOverride

1/2 NPTF Thd.Both Ends

24.8(0.98)

49.6(1.95)

106.8(4.21)

160.5(6.32)



A

2502-A3.p65, dd


Accessories Series D31*W

Micro Connector Options (7A, 7B, 1B & 1D)Manaplug (Options 6, 56, 1A & 1C)Interface – Brad Harrison Plug

– 3-Pin for Single Solenoid– 5-Pin for Double Solenoid

Solenoid (Positive)Wire #2 (Red/White)

GroundWire #1 (Green)

Solenoid (Negative)Wire #3 (Red/Black)

3-Pin Manaplug (Mini) with LightsSingle Solenoid Valves – Installed Opposite Side of Solenoid

“B” Solenoid (Positive)Wire #1 (Red/White)

“A” Solenoid (Negative)Wire #2 (Red)

“B” Solenoid (Negative)Wire #5 (Red/Black)

“A” Solenoid (Positive)Wire #4 (Red/Yellow)

GroundWire #3 (Green)

5-Pin Manaplug (Mini) with LightsSingle Solenoid Valves – Installed Opposite Side of Solenoid

Double Solenoid Valves – Installed Over “A” Solenoid(“A” and “B” Solenoids Reversed for #8 and #9 Spools)

Pins are as seen on valve (male pin connectors).

Manaplug – Electrical Mini PlugEP336-30 3 Pin PlugEP316-30 5 Pin Plug (Double Solenoid)EP31A-30 5 Pin Plug (Single Solenoid)

DESINA Connector (Option D)M12 pin assignmentStandard

Hirschmann Plug with Lights (Option P5)ISO 4400/DIN 43650 Form “A”

Conduit Box (Standard/Plug-In; Option G)Meets Nema 4/IP67

Signal Lights (Option 5)– LED Interface

Face View of Plug

Pins are as seen on valve (male pin connectors).

Manaplug – Electrical Micro PlugEP337-30 3 Pin PlugEP317-30 5 Pin Plug (Double Solenoid)EP31B-30 5 Pin Plug (Single Solenoid)

1

1

2

2

3

3

4

45

5

DESINA – designPin 1 and 2connected

1 = Not used

2 = Not used

3 = 0V

4 = Signal (24 V)

5 = Earth Ground

Pin #2(Positive)

(Negative)

Pin #3(Ground)

Pin #1


A

2502-A3.p65, dd


The following is important installation informationwhich applies to all directional control valves describedin this catalog.

Mounting PositionDetent – HorizontalSpring Offset – UnrestrictedSpring Centered – Unrestricted

Fluid RecommendationsPremium quality hydraulic oil with a viscosity rangebetween 32-54 cst. (150-250 SSU) At 38°C (100°F) isrecommended. The absolute operating viscosity range isfrom 16-220 cst. (80-1000 SSU). Oil should havemaximum anti-wear properties and rust and oxidationtreatment.

Fluids and SealsValves using synthetic, fire-resistant fluids requirespecial seals. When phosphate esters or its blends areused, FLUOROCARBON seals are required. Water-glycol, water-in-oil emulsions and petroleum oil may beused with STANDARD seals.

FiltrationFor maximum valve and system component life, thesystem should be protected from contamination at alevel not to exceed 125 particles greater than 10microns per milliliter of fluid (SAE class 4/ISO 16/13).

Series NFPA Size

D31V*, D3P D05H, CETOP 5 3/8"

D31D*, D3DP D05HE, CETOP 5H 3/8"

FOR MAXIMUM VALVE RELIABILITY, ADHERE TOTHE FOLLOWING INSTALLATION INFORMATION.

Mounting Patterns

Torque SpecificationsThe recommended torque values for the bolts whichmount the valve to the manifold or subplate are asfollows: 16.3 Nm (12 ft-lb).

Installation Information Series D31

SiltingSilting can cause any sliding spool valve to stick and notspring return if held under pressure for long periods oftime. The valve should be cycled periodically to preventsticking.

Special InstallationsConsult your Parker representative for any applicationrequiring the following:

• Pressure above rating.

• Fluid other than those specified.

• Oil temperature above 71.1°C (160°F).

• Flow path other than normal.

Torque to0.67 ±0.1 Nm(6 ± 1 in-lbs)

M5 x 0.8 Plug forVariations 2 & 5.Torque to2.44 ± .22 Nm(22 ± 2 in-lbs)

M6 x 1 Plug forVariations 1 & 2.Torque to2.44 ± .22 Nm(22 ± 2 in-lbs)

1/16 Pipe Plug for Variations 4 & 5Torque to:11.67 ± 1.67 Nm (105 ± 15 in-lbs)


NFPA D05HE, CETOP 5H Pattern D31DW

NFPA D05H, CETOP 5 Pattern D31VW




A

2502-A3.p65, dd


Style Description No Solenoid/Operator Solenoid/Operator A Solenoid/Operator BCode Energized Energized Energized

B Spring Offset P➝A and B➝T — P➝B and A➝T

C Spring Centered Centered P➝A and B➝T P➝B and A➝T

D Detented Last Position Held P➝A and B➝T P➝B and A➝T

E Spring Centered Centered — P➝B and A➝T

F† Spring Offset, Shift to Center P➝A and B➝T — Centered

H Spring Offset P➝B and A➝T P➝A and B➝T —

K Spring Centered Centered P➝A and B➝T —

M† Spring Offset, Shift to Center P➝B and A➝T Centered —

† D31*W only.

SERIES D31*W, D31*A, D31*LPILOT OPERATED,

DIRECTIONAL CONTROL VALVES

Tank and Drain Line SurgesIf several valves are piped with a common tank or drainline, flow surges in the line may cause an unexpectedspool shift. No spring style valves are most susceptibleto this. Separate tank and drain lines should be piped ininstallations where line surges are expected.

Electrical Failure orLoss of Pilot Pressure (D31*A)Should electric power fail or loss of pilot pressure occur,spring offset and spring centered valves will shift to thespring held position. Detented valves will stay in the lastposition held before power failure. If main flow does notfail or stop at the same time power fails, machineactuators may continue to function in an undesirablemanner or sequence.

Electrical Characteristics(Detented Spool)Only a momentary energizing of the solenoid isnecessary to shift and hold a detented spool. Minimumduration of the signal is 0.1 seconds for DC voltages. ForAC voltages the response time is 0.06 seconds. Spoolposition will be held provided the spool centerline is in ahorizontal plane, and not shock or vibration is present todisplace the spool.

Pilot/Drain CharacteristicsPilot Pressure: 6.9 to 345 Bar (100 to 5000 PSI)

External: An oil source sufficient to maintain minimumpilot pressure must be connected to the “X” port of themain body. When using the external pilot variation, an

M5 x 0.8 x 6mm long set screw must be present in themain body pilot passage. (For details see Dimensionpages.) This plug will be furnished in valves ordered withpilot code 2 or 5.

Internal: Flow is internally ported from the pressure portof the main valve body to the “P” port of the pilot valve.The pressure developed at the “P” port of the pilot valvemust be 100 PSI (6.9 Bar) minimum at all times.

If the valve center condition allows flow from pressure totank, 100 PSI (6.9 Bar) back pressure must bedeveloped in the tank line to ensure sufficient pilot forceat “P”. The “X” port in subplate must be plugged whenusing internal pilot variation (1/16 NPT).

Pilot Valve Drain:Maximum pressure 102 Bar (1500 PSI), 207 Bar(3000 PSI) optional.

External: When using an external drain, an M6 x 1 x10mm long set screw must be present in the main bodydrain passage. (For details see Dimension pages.) Thisplug will be furnished in valves ordered with drain code1 or 2.

Drain flow from the pilot valve is at the “Y” port of themain body and must be piped directly to tank. Maximumdrain line pressure is 102 Bar (1500 PSI), 207 Bar(3000 PSI) optional. Any drain line back pressure isadditive to the pilot pressure requirement.

Internal: Drain flow from the pilot valve is internallyconnected to the main valve tank port. Tank and drainpressure are then identical so tank line pressure shouldnot exceed 102 Bar (1500 PSI), 207 Bar (3000 PSI)optional. Any tank line back pressure is also additive tothe pilot pressure requirement. If flow surges (a cause ofpressure surges) are anticipated in the tank line, anexternal drain variation is recommended. The “Y” port insubplate must be plugged when using internal drainvariations.

D31*W, D31*A, D31*L Flow Paths



A

2502-A3.p65, dd


Style RecommendedDescription “X” & “Y” “X” Port “Y” Port Special Notes Control Valve

Code De-Pressurized Pressurized Pressurized For Pilot Oil

Two Position“X” Port may be pressurized to

BSpring Offset

P➝A, B➝T P➝A, B➝T P➝B, A➝T assist spring in returning spoolto offset position (ext. only)

Three PositionFlow paths will be reversed on

C Spring CenteredCenter P➝A, B➝T P➝B, A➝T valves with tandem center

(8) spools

Two-Position“Y” Port may be pressurized

H Spring OffsetP➝B, A➝T P➝A, B➝T P➝B, A➝T to assist spring in returning

spool to offset position

Pilot Drain CharacteristicsPilot Pressure: 6.9 to 345 Bar (100 to 5000 PSI)

Direct pilot operated valves use the “X” and “Y” ports tosupply pilot oil directly to the ends of the spool, providingspool shifting force. A block mounted on top of the valvebody is internally cored to make the necessaryconnections. Thus when “X” is pressurized, “Y” is usedas a drain; and when “Y” is pressurized, “X” becomes thedrain.

Any back pressure in these lines when they are beingused as a drain is additive to the pilot pressurerequirement.

Internal Drain: On spring offset models, only the “X”port is pressurized, as the spring returns the spool to itsat rest position. On these models, “Y” may be internallydrained through the main tank passage in the valve.

D3P Flow Path/Pilot Pressure

SERIES D3P, D3DP PILOT OPERATEDDIRECTIONAL CONTROL VALVES

Tank and Drain Line SurgesIf several valves are piped with a common tank or drainline, flow surges in the line may cause an unexpectedspool shift. Separate tank and drain lines should bepiped in installations where line surges are expected.

Loss of Pilot PressureShould oil pilot pressure fail, spring offset and springcentered valves will shift to the spring held position.Detented valves will stay in the last position held beforepower failure. If main flow does not fail or stop at thesame time power fails, machine actuators may continueto function in an undesirable manner or sequence.

Mounting PatternD3P valves may be mounted on a standard D05 patternsubplate or manifold only if the “X” and “Y” ports areexternally connected to the pilot block on top of the mainbody. All other mounting styles require a D05H orD05HE pattern which incorporates ports for the “X” and“Y” pilot and drain passages. Location of these ports canbe found on the Recommended Mounting Surfacepages in this section.


y A B

P T

y xA B

P T

xA B

P T


A

2502-A3.p65, dd


Series D31VW, D31VA, D31VL, D3PSubplate MountingNFPA D05H, CETOP 5

Recommended Mounting SurfaceSurface must be flat within .102 mm (0.0004 inch) T.I.Rand smooth within 812.8 micro-meters (32 micro-inch).Torque bolts to 16.3 Nm (12 ft-lbs).

Mounting Position

Valve Type Mounting PositionDetent (Solenoid) HorizontalSpring Offset UnrestrictedSpring Centered Unrestricted

For maximum valve reliability,adhere to the followinginstallation information.

Mounting PatternInch equivalents for millimeter dimensions are shown in (**)

M6x1 (1/4-20) UNC-2Bthread x 9.7 (.38) min.thread depth 4 places

11.2 (O.44) max.P.A.B. & T ports

3.96/4.78 (O.156/.188)max. X & Y ports

.56(.022)

.56(.022)

75.0(2.95)

91.9 (3.62) min. with X & Y ports72.1 (2.84) min. without X & Y ports

.28(.011)

A

A

A

B

B

B

46.0(1.81)

11.1(.44)

43.6(1.72)

6.4(.25)

27.0(1.06)

32.5(1.28)

2.4(.09)

37.3(1.47)

54.0(2.13)

50.8(2.00)

65.1(2.56)

57.9(2.28)min.

21.4(.84)

3.2(.13)

S

L

L

16.7(.66)



A

2502-A3.p65, dd


Series D31DW, D31DA, D31DL, D3DPSubplate MountingNFPA D05HE, CETOP 5H

Recommended Mounting SurfaceSurface must be flat within .102 mm (0.0004 inch) T.I.R.and smooth within 812.8 micro-meters (32 micro-inch).Torque bolts to 16.3 Nm (12 ft-lbs).

Mounting Position

Valve Type Mounting PositionDetent (Solenoid) HorizontalSpring Offset UnrestrictedSpring Centered Unrestricted

For maximum valve reliability,adhere to the followinginstallation information.

Mounting PatternInch equivalents for millimeter dimensions are shown in (**)


M6x1 (1/4-20) UNC-2Bthread x 9.7 (.38) min.thread depth 4 places

11.2 (O.44) max.P.A.B. & T ports

6.3 (O.25) max.X & Y ports

.56(.022)

.56(.022)

75.0(2.95)

91.9 (3.62) min. with X & Y ports72.1 (2.84) min. without X & Y ports

.28(.011)

A

A

A

A

B

B

B

Y

T

P

X

B

B

A

46.0(1.81)

11.1(.44)

11.1(.44)

43.6(1.72)

6.4(.25)

27.0(1.06)

32.5(1.28)

7.9(.31)

37.3(1.47)

54.0(2.13)

50.8(2.00)

61.9(2.44)

57.9(2.28)min.

21.4(.84)

S

L

L

16.7(.66)


A

2502-A3.p65, dd


Mounting Pattern NFPA D05H , CETOP 5NFPA D05HE, CETOP 5H

Maximum 345 Bar (5000 PSI)Operating “T” Port (tank):Pressure 34 Bar (500 PSI)

With External Drain:207 Bar (3000 PSI)

Maximum Flow See Switching Limit Charts

Pilot Pressure Air Min: 3.4 Bar (50 PSI)Air Max: 10.2 Bar (150 PSI)

Max. Drain Pressure 34 Bar (500 PSI)

Varies with pilot line size andResponse Time length, pilot pressure, pilot valve

shift time & flow capacity (GPM)

Technical Information Series D31*A

General Description

Series D31*A directional control valves are5-chamber, air pilot operated valves. The valves aresuitable for manifold or subplate mounting.

Features

• World design – Available worldwide.

• Mounting bolts below center line of spool – Minimizesspool binding.

• Five chamber style – Eliminates pressure spikes intubes, increasing valve life.

• High pressure and flow ratings – Increasedperformance options in a compact valve.

Pressure Drop Chart

10 20

151113

30 40

23

5

6

4

1

Flow

38 76

400

300

200

100

28

21

14

7

0

0

GPM

LPM

PSI Bar

Pre

ssur

e D

rop

( P

)

Specifications

D31VA Pressure Drop vs. FlowThe chart to the left provides the flow vs. pressure dropcurve reference for the D31VA Series valves by spool type.

Example:Find the pressure drop at 76 LPM (20 GPM) for a D31VAwith a number 1 spool. To the right of spool number 1, locatethe number 3 in the P-A column, and 2 in the B-T column.

Using the top graph, locate curves 2 and 3 and read thepressure drop values. Total pressure drop through the valveis the sum of the two values.

VISCOSITY CORRECTION FACTORViscosity (SSU) 75 150 200 250 300 350 400% of ΔP (Approx.) 93 111 119 126 132 137 141Curves were generated using 100 SSU hydraulic oil. For any otherviscosity, pressure drop will change as per chart.

D31VA Pressure Drop Reference Chart -- Curve NumberSpool Shifted Center Condition

No. P-A P-B B-T A-T (P-T) (B-A) (A-B) (P-A) (P-B) (A-T) (B-T)

1 3 3 2 1 - - - - - - -2 3 3 1 1 3 3 3 4 4 1 14 3 3 1 1 - - - - - 1 19 3 3 1 1 6 - - - - - -20 5 4 2 2 - - - - - - -30 4 3 1 1 - - - - - - -


A

2502-A3.p65, dd


Technical Information Series D31*A


DDirectional

Control ValveBasic Valve Air Operated

PilotSpool Style Seal

CompoundVariations

A

DesignSeriesNOTE:



Dimensions – Air Operated Inch equivalents for millimeter dimensions are shown in (**)

Note: 30.0mm (1.18") frombottom of bolt hole counterboreto bottom of valve.

Code Description31D NFPA D05HE,

CETOP 5H (ISO)

31V NFPA D05H,CETOP 5


B† Single operator, 2 position, spring offset.P to A and B to T in offset position.

C Double operator, 3 position,spring centered.

D† Double operator, 2 position, detent.

E Single operator, 2 position, spring centered.P to B and A to T when energized.

H† Single operator, 2 position, spring offset.P to B and A to T in offset position.

K Single operator, 2 position, spring centered.P to A and B to T when energized.


7 Pilot choke - meter out60 Pilot choke - meter in8 Stroke adj. 'B'9 Stroke adj. 'A'89 Stroke Adj. 'A' & 'B'90 BSPP Threads


A B

P T

b

A B

P T

b a

A B

P T

a

A B

P T

a

A B

P T

b

† Only spools20 and 30.

Valve schematic symbolsare per NFPA/ANSIstandards, providing flowP to A when energizingoperator A. Note operatorsreverse sides for #9 spool.See installation infor-mation for details.

Valve Weight:Double Operator5.7 kg (12.7 lbs.)

Standard Bolt Kit:BK98

Metric Bolt Kit:BKM98

This conditionvaries withspool code.

1

2

4

8†, 9*

20†

30*

† 8 and 20 spools haveclosed crossover.

* 9 and 30 spools haveopen crossover.

Code SymbolA B

P T

A B

P TA B

P T

A B

P TA B

P TA B

P T

A B

P T

b a

AirOperated

Pilot



Code Description1 Int. pilot/Ext. drain2 Ext. pilot/Ext. drain4# Int. pilot/Int. drain5 Ext. pilot/Int. drain

# Not available with 2, 7, 8 & 9 spools.

121.0(4.76)

96.0(3.78)

83.0(3.27)

134.9(5.31)

36.0(1.42)

72.3(2.84)

70.0(2.76)

35.0(1.38)

46.0

1/8" NPT Typ.

(1.81)

82.9(3.26)

35.0(1.38)

192.0(7.56)

58.9(2.32)

50.5(1.99)

47.2(1.86)

SeeNote


A

2502-A4.p65, dd


Technical Information Series D61VA

General DescriptionSeries D61VA directional control valves are5-chamber, air pilot operated valves. They areavailable in 2 or 3-position styles. These valvesare manifold or subplate mounted, and conformto NFPA's D08, CETOP 8 mounting patterns.

Specifications

Mounting Pattern NFPA D08, CETOP 8, NG25

Maximum P, A, B: 207 Bar (3000 PSI)Operating “T” Port (tank):Pressure 34 Bar (500 PSI)


Maximum Flow See Reference Data



Response Time Varies with pilot line size andlength, pilot pressure, pilot valveshift time & flow capacity (GPM)

Features• Low pressure drop.

• Fast response option available.

• Hardened spools provide long life.

Code Description61V NFPA D08,

CETOP 8


7 Pilot choke – meter out

60 Pilot choke – meter in

8 Stroke adj. 'B'

9 Stroke adj. 'A'

89 Stroke Adj. 'A' & 'B'

90 BSPP Threads


# Not available with 2, 8 & 9 spools.


B Single operator, 2 position, spring offset.P to A and B to T in offset position.

C Double operator, 3 position, spring centered.

D Double operator, 2 position, detent.

E Single operator, 2 position, spring offset to center.P to B and A to T in shifted position.

H Single operator, 2 position, spring offset.P to B and A to T in offset position.

K Single operator, 2 position. Spring offset to center.P to A and B to T in shifted position.

A B

P T

b

A B

P T

b a

* 8 spool has closed crossover.** 9 spool has open crossover.

1 8*9**

2 11

4 12


A B

P T

A B

P T

A B

P T

A B

P T

A B

P T

A B

P T

Valve schematic symbols are per NFPA/ANSIstandards, providing flow P to A when energizingoperator A. Note operators reverse sides for #8 and#9 spools. See installation information for details.


D 61VDirectional



Compound

A

DesignSeriesNOTE:



Variations


A B

P T

b a

A B

P T

a

A B

P T

a

A B

P T

b




AirOperated

Pilot





A

2502-A4.p65, dd


Dimensions Series D61VA



165.6(7.31)

192.0(7.56)

96.4(3.80)

48.1(1.89)

129.5(5.10)

128.3(3.03)

117.8(4.64)

114.3(4.50)

9.5(0.37) 57.2

(2.25)

160.4(6.31)

132.3(5.21)

108.5(4.27)

64.5(2.54) 46.0

(1.81)23.0(0.91)

#10-24 Plug locations forVariations 1 & 2External pilot drain

1/16 Pipe plug location forVariations 2 & 5External pilot supply or internal pilotwith back pressure check

SECTION A-A

36.4(1.43)

SeeNote

1/8 NPT


A

2502-A4.p65, dd


Mounting Pattern NFPA D08 (formerly D06),CETOP 8, NG25

Max. Operating Press. 207 Bar (3000 PSI)

Max. Tank Line Press. 207 Bar (3000 PSI)


Min. Pilot Pressure 5.1 Bar* (75 PSI)

Max. Pilot Pressure 207 Bar (3000 PSI)

Nominal Flow 189 Liters/Min (50 GPM)

Maximum Flow See Reference Chart

Technical Information Series D6P

General DescriptionSeries D6P directional control valves are 5-chamber,pilot operated valves. They are available in2 or 3-position styles. These valves are manifold orsubplate mounted, and conform to NFPA's D08,CETOP 8 mounting patterns.

Features• Low pressure drop design.



Specifications

* 6.9 Bar (100 PSI) for 2, 8, 9 & 12 spools

For flow path, pilot drain and pilot pressure details, seeInstallation Information.

Response TimeResponse time will vary with pilot line size, pilot linelength, pilot pressure shift time and flow capacity of thecontrol valve.

Shift VolumeThe pilot chamber requires a volune of 0.54 in3 forcenter to end and 1.08 in3 for end to end.

Code TypeN NitrileV Fluorocarbon

Code Description2 External — External5# External — Internal

# Available in “B” & “H” styles only.


7 Pilot Choke – Meter Out

60 Pilot Choke – Meter In

8 Stroke adj. ‘B’

9 Stroke adj. ‘A’

20 Fast response

89 Stroke adj. ‘A’ & ‘B’


B Single operator, 2 position, spring offset.P to A and B to T in offset position.

C Double operator, 3 position, spring centered.

H Single operator, 2 position, spring offset.P to B and A to T in offset position.

Thisconditionvarieswith spoolcode.

y A B

P Ty xA B

P T

xA B

P T


* 8 spool has closed crossover.** 9 spool has open crossover.

1 8* 9**

2 11

4 12


A B

P T

A B

P T

A B

P T

A B

P TA B

P TA B

P T




Valve schematic symbols are per NFPA/ANSIstandards, providing flow P to A when energizingoperator X. Note operators reverse sides for #8 and#9 spools. See installation information for details.

D 6Directional


Compound

P

DesignSeriesNOTE:



Variations

OilOperator



NFPA D08CETOP 8


A

2502-A4.p65, dd


Dimensions Series D6P


Pilot Operated with Pilot Choke Control

Standard Pilot Operated


130.2(5.13)53.2

(2.10)

129.2(5.09)

128.1(5.05)

48.1(1.89)

143.3(5.65)

108.5(4.27)

40.1(1.58)

9.5(0.38) 57.1

(2.25) 114.3(4.50)117.8

(4.64)

77.0(3.03)129.5

(5.10)

#10-24 Plug location forVariations 1 & 2External pilot drain

1/16 Pipe plug locationfor Variations 2 & 5External pilot supply orinternal pilot with backpressure check

91.9(3.62)

12.8(0.50)

#6 SAE

SeeNote

257.8(10.16)

Ref.

Pilot ChokeControl

Variation 7

39.6(1.56)

183.6(7.23)



A

2502-A5.p65, dd



Maximum 350 Bar (5000 PSI)Operating “T” Port (tank):Pressure 34 Bar (500 PSI)


Maximum Flow See Reference Data Charts





General DescriptionSeries D81VA directional control valves are5-chamber, air pilot operated valves. They are availablein 2 or 3-position styles. These valves are manifold orsubplate mounted, and conform to NFPA's D08,CETOP 8 mounting pattern.




NFPA D08

CETOP 8



# Not available with 2, 8, 9 & 30 spools.Code Description Symbol

B† Sgl. operator, 2 position, spring offset.P to A and B to T in offset position.

C Dbl. operator, 3 position,spring centered.

D† Dbl. operator, 2 position, detent.

E Sgl. operator, 2 position, spring centered.P to B and A to T when energized.

H† Sgl. operator, 2 position, spring offset.P to B and A to T in offset position.

K Sgl. operator, 2 position. Spring centered.P to A and B to T when energized.

A B

P T

b

A B

P T

b a

A B

P T

b a

A B

P T

a

A B

P T

A B

P T

b

* 8 & 20 spool has closed crossover.** 9 & 30 spools have open crossover.

1 11

2 12

4 20*

8** 30**9**

Code Symbol Code SymbolA B

P TA B

P T

A B

P TA B

P T

A B

P TA B

P TA B

P T

A B

P T

Valve Weight: Single Operated19.9 kg (43.9 lbs.)



Valve schematic symbols are per NFPA/ANSIstandards, providing flow P to A when energizingoperator A. Note operators reverse sides for #9spool. See installation information for details.

D 81VDirectional

Control ValveBasic Valve Spool Style Seal

CompoundVariations

APilot Supplyand Drain

DesignSeriesNOTE:

Notrequired

whenordering.


†Available with 20 & 30 spools only.


7 Pilot choke –meter out

60 Pilot choke –meter in

8 Stroke adj. 'B'9 Stroke adj. 'A'89 Stroke Adj. 'A' & 'B'90 BSPP Threads

This conditionvaries withspool code.

Air OperatedPilot

Specifications

Air OperatedPilot




A

2502-A5.p65, dd




96.0(3.78)

96.0(3.78)

153.1(6.03)

57.0(2.24)

153.1(6.03)

179.4(7.06)

127.5(5.02)

47.1(1.85)

58.0(2.28) 116.0

(4.57)116.5(4.59)

82.9(3.26)

82.9(3.26)

52.5(2.07)

M6 x 1 Plug forVariations 1 & 2Torque to:1.78 ±0.22 Nm(16 ±2 in-lbs)Do Not Loctite

1/16 Plug for Variations 2 & 5Torque to:11.67 ±1.67 Nm(105 ±15 in-lbs)Do Not Loctite

1/8 NPT

Air Operated

Note: 57mm (2.24") from bottom of bolt hole counterbore to bottom of valve.


A

2502-A5.p65, dd



General DescriptionSeries D8P directional control valves are 5-chamber,pilot operated valves. They are available in 2 or 3-position styles. These valves are manifold or subplatemounted, and conform to NFPA's D08, CETOP 8mounting pattern.



Specifications

Mounting Pattern NFPA D08 (formerly D06),CETOP 8, NG25

Max. Operating Pressure 350 Bar (5000 PSI)

Max. Tank Line Pressure 350 Bar (5000 PSI)


Min. Pilot Pressure 5.1 Bar* (75 PSI)


Nominal Flow 302 LPM (80 GPM)

Max. Flow See Reference Data Chart

* 6.9 Bar (100 PSI) for 2, 8, 9 & 12 spools10.3 Bar (150 PSI) for pressure centered models

For flow path, pilot drain and pilot pressure details, see InstallationInformation.


Shift VolumeThe pilot chamber requires a volume of 1.35 in3

(22.1 cc) for center to end.Ordering Information

NFPA D08CETOP 8



B† Sgl. operator, 2 position, spring offset.P to A and B to T in offset position.

C Dbl. operator, 3 position, spring centered.

H† Sgl. operator, 2 position, spring offset. P to Band A to T in offset position.

† Available with 20 & 30 spools only.

y A B

P T

y xA B

P TxA B

P T

This conditionvaries with spoolcode.

* 20 spool has closed crossover.** 9 & 30 spools have open crossover.

1 11

2 12

4 20*

7 30**

8**9**


A B

P TA B

P T

A B

P T

A B

P T

A B

P TA B

P T

A B

P T

A B

P T


# Available in “B” style only.

Valve Weight: 18.9 kg (41.7 lbs.) Standard Bolt Kit: BK228 Metric Bolt Kit: BKM228Valve schematic symbols are per NFPA/ANSI standards, providing flow P to Awhen energizing operator X. Noteoperators reverse sides for #9 spool.See installation information for details.

D 8

DirectionalControlValve

BasicValve

Actuator Spool Style SealCompound

Variations

P


DesignSeriesNOTE:

Notrequired

whenordering.

A B

P T

Code Description

Omit Standard7 Pilot choke –

meter out60 Pilot choke –

meter in8 Stroke adj. 'B'9 Stroke adj. 'A'89 Stroke Adj. 'A' & 'B'90 BSPP Threads

OilOperator

Bold: Designates Tier I products and options.Non-Bold: Designates Tier II products and options.

These products will have longer lead times.


A

2502-A5.p65, dd


Series D8PDimensions


Pilot ChokeControl

Variation 7

39.6(1.56)

212.4(8.37)


Standard Pilot Operated

130.2(5.13)53.2

(2.10)

92.1(3.63)

12.0(0.47)

77.0(3.03)

306.2(12.06)

Ref.

176.9(6.97)

181.0(7.13)90.5

(3.57)31.3

(1.23)

57.0(2.25)

17.5(0.69)153.1

(6.03)153.1(6.03)

47.8(1.88)

2.4(0.10)

151.0(5.95)

127.5(5.02)

48.0(1.89)

6.3(0.25) 57.2

(2.25) 114.3(4.50)

M6 x 1 Plug forVariations 1, 2 & 3Torque to:

1.78 ±0.22 Nm(16 ±2 in-lbs)Do Not Loctite

1/16 Plug for Variations 2 & 5Torque to:

11.67 ±1.67 Nm(105 ±15 in-lbs)Do Not Loctite

Note: 57mm (2.24") from bottom of bolt hole counterbore to bottom of valve.


A

2502-A6.p65, dd



Maximum 207 Bar (3000 PSI)Operating “T” Port (tank): 34 Bar (500 PSI)

Pressure With External Drain:207 Bar (3000 PSI)






General Description

Series D101VA directional control valves are5-chamber, air pilot operated valves. They areavailable in 2 or 3-position styles. These valves aremanifold or subplate mounted, and conform toNFPA's D10, CETOP 10 mounting pattern.

Specifications



NFPA D10CETOP 10

Code Type

N Nitrile

V Fluorocarbon

Code Description

1 Int. pilot/Ext. drain

2 Ext. pilot/Ext. drain

4# Int. pilot/Int. drain

5 Ext. pilot/Int. drain# Not available with 2, 8 & 9 spools.


B† Sgl. solenoid, 2 position, spring offset.P to A and B to T in offset position.

C Dbl. solenoid, 3 position, spring centered.

H† Sgl. solenoid, 2 position, spring offset.P to B and A to T in offset position.

† Available with 1, 2, 4 & 11 spools only. This condition varieswith spool code.

A B

P T

b

A B

P T

b a

A B

P T

a

Code Symbol

* 8 spool has closedcrossover.

** 9 spool has opencrossover.

1

2

4

8*9**

11

A B

P T

A B

P T

A B

P TA B

P TA B

P T




Valve schematicsymbols are perNFPA/ANSIstandards, providingflow P to A whenenergizing operator A.Note operatorsreverse sides on #8and #9 spools. Seeinstallationinformation for details.

DesignSeriesNOTE:


D 101VDirectional



CompoundVariations

APilot Supplyand Drain



7 Pilot choke – meter out

60 Pilot choke – meter in

8 Stroke adj. 'B'

9 Stroke adj. 'A'

89 Stroke adj. 'A' & 'B'

90 BSPP Threads

Air OperatedPilot




A

2502-A6.p65, dd




82.9(3.26)

96.0(3.78)

96.0(3.78)

175.5(6.91)

73.2(2.88)

175.5(6.91)

36.8(1.45)

Orifice for Variation 20Fast Response

#10-24 Plug forExternal Pilot Drain(Pilot Supply & DrainCodes 1 & 2)

1/16 Plug forExternal Pilot Supplyand Internal Check(Pilot Supply &Drain Codes 2 & 5)

Section A-A

210.4(8.28)

158.8(6.25)

18.8(0.74)

29.3(1.15)

196.1(7.72)

199.1(7.84)

1/8 NPT

Air Operated



A

2502-A6.p65, dd



General DescriptionSeries D10P directional control valves are 5-chamber,pilot operated valves. They are available in 2 or 3-position styles. These valves are manifold or subplatemounted, and conform to NFPA's D10, CETOP 10mounting pattern.



SpecificationsMounting Pattern NFPA D10, CETOP 10, NG32

Max. Operating Pressure 207 Bar (3000 PSI)

Max. Tank Line Pressure 207 Bar (3000 PSI)


Min. Pilot Pressure 4.4 Bar (65 PSI)


Nominal Flow 378 LPM (100 GPM)


For flow path, pilot drain and pilot pressure details, seeInstallation Information.


Shift VolumeThe pilot chamber requires a volume of1.51 in3 (24.75 cc) for center to end.


NFPA D10CETOP 10



# Available in “B” & “H” styles only.


B† Sgl. solenoid, 2 position, spring offset.P to A and B to T in offset position.

C Dbl. solenoid, 3 position, spring centered.

H† Sgl. solenoid, 2 position, spring offset.P to B and A to T in offset position.

† Available with 1, 2, 4 & 11 spools only.

y A B

P Ty xA B

P T

xA B

P T


Code Symbol

1

2

4

8*9**

11

* 8 spool has closedcrossover.

** 9 spool has opencrossover.

A B

P TA B

P T

A B

P TA B

P TA B

P T




Valve schematic symbolsare per NFPA/ANSIstandards, providing flowP to A when energizingoperator X. Noteoperators reverse sideson #8 and #9 spools. Seeinstallation information fordetails.

DesignSeriesNOTE:

Notrequired

whenordering.

D 10Directional


CompoundVariations

PPilot Supplyand Drain


7 Pilot choke –meter out

60 Pilot choke –meter in

8 Stroke adj. 'B'

9 Stroke adj. 'A'

89 Stroke Adj. 'A' & 'B'

90 BSPP Threads

OilOperator




A

2502-A6.p65, dd


Series D10P


Dimensions


Standard Pilot Operated190.5(7.51)76.2

(3.00)

158.7(6.25)

19.3(0.76)

114.3(4.50)

175.5(6.91)

Orifice for Fast ResponseVariation 20

#10-24 Plug for ExternalPilot Drain(Pilot supply and draincodes 1 & 2)

1/16 Plug for External PilotSupply and Internal Check(Pilot supply and draincodes 2 & 5)

Section A–A

190.5(7.51)

5.1(0.20)

76.2(3.00)

172.3(6.79)

36.8(1.45)

175.5(6.91)

60.3(2.38)

175.5(6.92)

190.6(7.51)

158.4(6.24)

56.8(2.24)

19.1(0.75) 98.4

(3.88)199.1(7.84)

39.0(1.54)

351.0(13.83)

Ref.

x# 6 SAE

39.6(1.56)

231.8(9.13)

Pilot ChokeControl

Variation 7

Note: 36.83mm (1.45") frombottom of bolt hole counterboreto bottom of valve.

Note: 36.83mm (1.45") from bottom of bolt holecounterbore to bottom of valve.

Date post:	07-Mar-2018
Category:	Documents
Upload:	duongnhan
View:	225 times
Download:	1 times

Directional Control Valveshasmak.com.tr/parkervalf/Parker Pilot Operated Directional...

Documents