Date post: | 27-Oct-2015 |
Category: |
Documents |
Upload: | cesarsanfelice |
View: | 268 times |
Download: | 9 times |
Serve atOnce Traffica Traffica Z5.2
DX200 Clear Code List
DN078927
Issue 1-0
2 DN078927Issue 1-0
DX200 Clear Code List
Id:0900d80580635bef
The information in this document is subject to change without notice and describes only the product defined in the introduction of this documentation. This documentation is intended for the use of Nokia Siemens Networks customers only for the purposes of the agreement under which the document is submitted, and no part of it may be used, reproduced, modified or transmitted in any form or means without the prior written permission of Nokia Siemens Networks. The documentation has been prepared to be used by professional and properly trained personnel, and the customer assumes full responsibility when using it. Nokia Siemens Networks welcomes customer comments as part of the process of continuous development and improvement of the documentation.
The information or statements given in this documentation concerning the suitability, capacity, or performance of the mentioned hardware or software products are given "as is" and all liability arising in connection with such hardware or software products shall be defined conclusively and finally in a separate agreement between Nokia Siemens Networks and the customer. However, Nokia Siemens Networks has made all reasonable efforts to ensure that the instructions contained in the document are adequate and free of material errors and omissions. Nokia Siemens Networks will, if deemed necessary by Nokia Siemens Networks, explain issues which may not be covered by the document.
Nokia Siemens Networks will correct errors in this documentation as soon as possible. IN NO EVENT WILL Nokia Siemens Networks BE LIABLE FOR ERRORS IN THIS DOCUMENTA-TION OR FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO SPECIAL, DIRECT, INDI-RECT, INCIDENTAL OR CONSEQUENTIAL OR ANY LOSSES, SUCH AS BUT NOT LIMITED TO LOSS OF PROFIT, REVENUE, BUSINESS INTERRUPTION, BUSINESS OPPORTUNITY OR DATA,THAT MAY ARISE FROM THE USE OF THIS DOCUMENT OR THE INFORMATION IN IT.
This documentation and the product it describes are considered protected by copyrights and other intellectual property rights according to the applicable laws.
The wave logo is a trademark of Nokia Siemens Networks Oy. Nokia is a registered trademark of Nokia Corporation. Siemens is a registered trademark of Siemens AG.
Other product names mentioned in this document may be trademarks of their respective owners, and they are mentioned for identification purposes only.
Copyright © Nokia Siemens Networks 2010/9/9. All rights reserved
f Important Notice on Product Safety Elevated voltages are inevitably present at specific points in this electrical equipment. Some of the parts may also have elevated operating temperatures.
Non-observance of these conditions and the safety instructions can result in personal injury or in property damage.
Therefore, only trained and qualified personnel may install and maintain the system.
The system complies with the standard EN 60950 / IEC 60950. All equipment connected has to comply with the applicable safety standards.
The same text in German:
Wichtiger Hinweis zur Produktsicherheit
In elektrischen Anlagen stehen zwangsläufig bestimmte Teile der Geräte unter Span-nung. Einige Teile können auch eine hohe Betriebstemperatur aufweisen.
Eine Nichtbeachtung dieser Situation und der Warnungshinweise kann zu Körperverlet-zungen und Sachschäden führen.
Deshalb wird vorausgesetzt, dass nur geschultes und qualifiziertes Personal die Anlagen installiert und wartet.
Das System entspricht den Anforderungen der EN 60950 / IEC 60950. Angeschlossene Geräte müssen die zutreffenden Sicherheitsbestimmungen erfüllen.
DN078927Issue 1-0
3
DX200 Clear Code List
Id:0900d80580635bef
Table of ContentsThis document has 164 pages.
Summary of changes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
2 Use of clear codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132.1 Traffic observation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132.2 Traffic measurement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132.3 Maintenance supervision . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132.4 Detailed charging. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132.5 Field reporting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
3 Presentation of clear codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
4 Effective and ineffective cause codes . . . . . . . . . . . . . . . . . . . . . . . . . . 15
5 Clear codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 225.1 000H - NORMAL END OF CALL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 225.2 001H - SUSPENDED CALL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 225.3 003H - CALL DURATION BELOW SUPERVISION TIME . . . . . . . . . . . 235.4 004H - B BUSY OR CONGESTION RECEIVED FROM OUTGOING CIR-
CUIT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 235.5 005H - CALLED SUBSCRIBER BUSY . . . . . . . . . . . . . . . . . . . . . . . . . 245.6 006H - TIME-OUT FOR B-SUBSCRIBER ANSWER . . . . . . . . . . . . . . 245.7 007H - CALL WAITING TIME-OUT . . . . . . . . . . . . . . . . . . . . . . . . . . . . 255.8 008H - CALLED SUBSCRIBER NOT CONNECTED . . . . . . . . . . . . . . 265.9 009H - CALL ALREADY WAITING . . . . . . . . . . . . . . . . . . . . . . . . . . . . 265.10 00AH - INTERVENTION ALREADY ON . . . . . . . . . . . . . . . . . . . . . . . . 275.11 00BH - REROUTING DUE TO B-SUBSCRIBER FACILITY . . . . . . . . . 275.12 00CH - OUTGOING DIRECTION RESTRICTED DUE TO CRISIS MODE
285.13 00EH - MALICIOUS CALL TRACING . . . . . . . . . . . . . . . . . . . . . . . . . . 285.14 00FH - INTERMEDIATE CHARGING . . . . . . . . . . . . . . . . . . . . . . . . . . 295.15 010H - ABSENT SUBSCRIBER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 305.16 011H - OPERATOR PRIORITY ACCESS . . . . . . . . . . . . . . . . . . . . . . . 305.17 012H - NO PAGING RESPONSE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 315.18 013H - CALL TRANSFER RECALL DUE TO C-SUBSCRIBER ANSWER
TIME-OUT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 315.19 015H - NORMAL UNSPECIFIED. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 325.20 016H - SUBSCRIBER'S CHARGING CAPACITY EXCEEDED IN THE EX-
CHANGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 325.21 018H - INTERMEDIATE CHARGING IN THE END OF THE PHASE
CHARGING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 335.22 020H - ANNOUNCEMENT SUCCESS IN INTERCEPTION . . . . . . . . . 335.23 025H - CALL DROP BACK RELEASE . . . . . . . . . . . . . . . . . . . . . . . . . 345.24 031H - NOT ENOUGH CREDIT TO CALL . . . . . . . . . . . . . . . . . . . . . . 355.25 100H - CIRCUIT RE-SEIZED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 355.26 101H - CIRCUIT RELEASED BEFORE 'END OF THE CALL' NOTICE 36
4 DN078927Issue 1-0
DX200 Clear Code List
Id:0900d80580635bef
5.27 102H - CALL RECORD RELEASED DURING CALIBRATION . . . . . . . 365.28 103H - CHARGING IN WRONG PHASE OF CALL . . . . . . . . . . . . . . . . 375.29 201H - CALL RELEASED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 375.30 202H - CLEAR REQUEST RECEIVED FROM OUTGOING CIRCUIT. . 385.31 203H - B-CHANNEL UNACCEPTABLE . . . . . . . . . . . . . . . . . . . . . . . . . 395.32 204H - ESTABLISHED B-CHANNEL . . . . . . . . . . . . . . . . . . . . . . . . . . . 395.33 206H - CALL REJECTED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 405.34 207H - SUBSCRIBER CONGESTION . . . . . . . . . . . . . . . . . . . . . . . . . . 405.35 20BH - CLEAR IN DETAILED CHARGING . . . . . . . . . . . . . . . . . . . . . . 415.36 20EH - CALLING SUBSCRIBER LINE VACANT OR OUT OF SERVICE .
415.37 20FH - CHANGE OF OUTGOING CIRCUIT . . . . . . . . . . . . . . . . . . . . . 425.38 210H - NULL NUP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 425.39 211H - NETWORK, REJECTED DIVERTED CALLS . . . . . . . . . . . . . . . 435.40 213H - NETWORK, USER NOT IN CUG . . . . . . . . . . . . . . . . . . . . . . . . 445.41 215H - CALL DROP BACK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 445.42 216H - MISDIALLED TRUNK PREFIX . . . . . . . . . . . . . . . . . . . . . . . . . . 455.43 217H - TEMPORARY OUT OF ORDER. . . . . . . . . . . . . . . . . . . . . . . . . 455.44 218H - OUT OF CATCHMENT AREA . . . . . . . . . . . . . . . . . . . . . . . . . . 465.45 219H - TRANSLATION OUT-OF-SERVICE . . . . . . . . . . . . . . . . . . . . . . 475.46 220H - ANONYMOUS CALLS REJECTION. . . . . . . . . . . . . . . . . . . . . . 475.47 252H - UNTERMINATED CALL TO A PORTED NUMBER . . . . . . . . . . 485.48 300H - CALLING SUBSCRIBER BARRED DUE TO RESTRICTION IN
THE OUTGOING DIRECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 485.49 301H - CALLING SUBSCRIBER'S OUTGOING CALL RESTRICTED BY
OPERATOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 495.50 304H - CALLED SUBSCRIBER LINE OUT OF SERVICE . . . . . . . . . . . 505.51 305H - CALLED SUBSCRIBER LINE FAULTY . . . . . . . . . . . . . . . . . . . 505.52 306H - ACCESS TO B-SUBSCRIBER LINE RESTRICTED . . . . . . . . . 515.53 307H - B-NUMBER UNUSED. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 515.54 308H - B-NUMBER CHANGED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 525.55 309H - TIME-OUT WHEN WAITING FOR OPERATOR'S INTERVENTION
535.56 30AH - CLEAR/CALLING SUBSCRIBER HAS MADE ONHOOK DURING
SET-UP PHASE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 535.57 30BH - CLEAR/CALLING SUBSCRIBER HAS MADE ONHOOK WHEN
WAITING FOR ANSWER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 545.58 30CH - REANSWER TIME OUT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 545.59 30DH - B- OR C-NUMBER IS NOT REGISTERED . . . . . . . . . . . . . . . . 555.60 30EH - CALLED SUBSCRIBER LINE BLOCKED . . . . . . . . . . . . . . . . . 565.61 30FH - CHANGE IN NUMBERING PLAN. . . . . . . . . . . . . . . . . . . . . . . . 565.62 310H - CLOSED USER GROUP RESCTRICTION . . . . . . . . . . . . . . . . 575.63 311H - BEARER SERVICE NOT PROVIDED . . . . . . . . . . . . . . . . . . . . 575.64 312H - TELESERVICE NOT PROVIDED . . . . . . . . . . . . . . . . . . . . . . . . 585.65 315H - CALLED SUBSCRIBER HAS CALL DIVERSION BARRING . . . 585.66 317H - TIME-OUT IN INTELLIGENT NETWORK BASED SUBSCRIBER
SERVICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 595.67 31AH - INCOMING CALLS BARRED WITHIN THE CUG . . . . . . . . . . . 60
DN078927Issue 1-0
5
DX200 Clear Code List
Id:0900d80580635bef
5.68 31CH - SUBSCRIBER NOT A MEMBER OF THE CUG . . . . . . . . . . . . 605.69 31DH - OUTGOING CALLS BARRED WITHIN THE CUG . . . . . . . . . . 615.70 321H - NO CUG SELECTED. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 625.71 322H - UNKNOWN CUG INDEX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 625.72 400H - ATTENUATOR CONGESTION . . . . . . . . . . . . . . . . . . . . . . . . . 635.73 401H - INTERWORKING UNIT CONGESTION . . . . . . . . . . . . . . . . . . 635.74 402H - REGISTER TOTAL TIME EXCEEDED . . . . . . . . . . . . . . . . . . . 645.75 403H - MFCU DEVICE CONGESTION . . . . . . . . . . . . . . . . . . . . . . . . . 655.76 404H - PBRU DEVICE CONGESTION . . . . . . . . . . . . . . . . . . . . . . . . . 655.77 405H - ERRONEOUS SERVICE REQUEST FROM CO-PROCESS . . 665.78 406H - CONNECTION FAILED IN GSW/SWI . . . . . . . . . . . . . . . . . . . . 665.79 407H - ERRONEOUS ANSWER FROM PARTNER PROGRAM BLOCK.
675.80 408H - LENGTH OF CALLED SUBSCRIBER NUMBER EXCEEDED . 685.81 409H - CONNECTION FAILED IN SSW/SWI . . . . . . . . . . . . . . . . . . . . 695.82 40AH - CIRCUIT CONGESTION DUE TO TRAFFIC TYPE . . . . . . . . . 695.83 40BH - HOP COUNTER EXHAUST . . . . . . . . . . . . . . . . . . . . . . . . . . . 705.84 506H - LINES OF LINE HUNTING GROUPS BARRED . . . . . . . . . . . . 715.85 508H - CHARGING ERROR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 715.86 509H - FILE ERROR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 725.87 50BH - MODULE ROUTE OR SSW CONGESTION. . . . . . . . . . . . . . . 725.88 50CH - MFC-ASS-CHANNEL CLOSING MISSED . . . . . . . . . . . . . . . . 735.89 50DH - FACILITY CONTROL FAILED. . . . . . . . . . . . . . . . . . . . . . . . . . 735.90 50FH - UNSUITABLE MODULE CIRCUIT . . . . . . . . . . . . . . . . . . . . . . 745.91 600H - FILE RECORD CONGESTION . . . . . . . . . . . . . . . . . . . . . . . . . 755.92 601H - MODULE OR V5 CONGESTION. . . . . . . . . . . . . . . . . . . . . . . . 755.93 602H - REGISTER CONGESTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . 765.94 603H - NO RESPONSE FROM PARTNER PROGRAM BLOCK . . . . . 765.95 604H - INTERNAL CALL LINK CONGESTION . . . . . . . . . . . . . . . . . . . 775.96 606H - CONFERENCE DEVICE CONGESTION . . . . . . . . . . . . . . . . . 785.97 607H - POLARITY REVERSAL FAILURE. . . . . . . . . . . . . . . . . . . . . . . 785.98 608H - CHARGING NOT STARTED . . . . . . . . . . . . . . . . . . . . . . . . . . . 795.99 609H - CALL CLEARED BY MML . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 795.100 60BH - OVERLOAD CONGESTION . . . . . . . . . . . . . . . . . . . . . . . . . . . 805.101 60DH - STAGE CIRCUIT CONGESTION . . . . . . . . . . . . . . . . . . . . . . . 815.102 60EH - UNIT RESTARTED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 815.103 60FH - SUBSCRIBER MODULE OR V5 INTERFACE FAILURE, CALL
CLEARED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 815.104 700H - LONG AON REQUEST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 825.105 701H - REGISTER ANALYSIS FAILED. . . . . . . . . . . . . . . . . . . . . . . . . 835.106 702H - QUEUEING TIME EXCEEDED . . . . . . . . . . . . . . . . . . . . . . . . . 845.107 704H - PARITY ERROR FROM PBRU/MFCU DEVICE . . . . . . . . . . . . 845.108 705H - MODULE OR V5 INTERFACE NOT AVAILABLE . . . . . . . . . . . 855.109 706H - CALL INTERRUPTED DURING REGISTER ANALYSIS . . . . . 865.110 707H - SUBSCRIBER MODULE RESTARTED. . . . . . . . . . . . . . . . . . . 865.111 70AH - FORCED CLEAR OF A CALL . . . . . . . . . . . . . . . . . . . . . . . . . . 875.112 70BH - MODEM ERROR. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
6 DN078927Issue 1-0
DX200 Clear Code List
Id:0900d80580635bef
5.113 70CH - OVERLOAD CONTROL SYSTEM ERROR . . . . . . . . . . . . . . . . 885.114 70DH - ANNOUNCEMENT SERVICE FAILURE . . . . . . . . . . . . . . . . . . 885.115 70EH - CONFIGURATION ERROR . . . . . . . . . . . . . . . . . . . . . . . . . . . . 895.116 710H - NO ANALYSIS FOR CARRIER ACCESS CODE . . . . . . . . . . . . 895.117 711H - TARIFF NOT ACCEPTED BY TRANSIT EXCHANGE . . . . . . . . 905.118 712H - TARIFF NOT ACCEPTED BY ORIGINATING OR INTERWORK-
ING EXCHANGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 905.119 713H - NO ISUP ROUTE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 915.120 714H - ATTRIBUTE DIRECTED ROUTING MISMATCH . . . . . . . . . . . . 915.121 715H - REQUESTED FACILITY WAS NOT AVAILABLE ON THE OUTGO-
ING ROUTE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 925.122 716H - REQUESTED BEARER CAPABILITY COULD NOT BE FUL-
FILLED ON THE ROUTE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 935.123 718H - DIGIT ANALYSIS IN CENTRAL MEMORY RESULTED IN CON-
GESTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 935.124 719H - NO RESOURCE AVAILABLE FOR CALL . . . . . . . . . . . . . . . . . 945.125 71AH - IDENTIFIED CHANNEL NOT EXIST . . . . . . . . . . . . . . . . . . . . . 955.126 71BH - REQUESTED CHANNEL NOT AVAILABLE . . . . . . . . . . . . . . . 955.127 71CH - PACKET CONTROL UNIT CONGESTION . . . . . . . . . . . . . . . . 965.128 71DH - POINT-TO-POINT PROTOCOL ERROR . . . . . . . . . . . . . . . . . . 965.129 801H - LENGTH OF ORIGINAL CALLED SUBSCRIBER NUMBER EX-
CEEDED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 975.130 802H - LENGTH OF CALLING SUBSCRIBER NUMBER EXCEEDED . 975.131 803H - INVALID CALLING SUBSCRIBER CATEGORY . . . . . . . . . . . . 985.132 804H - OUTGOING CIRCUIT CONGESTION . . . . . . . . . . . . . . . . . . . . 995.133 806H - IDENTITY OF CALLING SUBSCRIBER IS NOT AVAILABLE . . 995.134 809H - ERRONEOUS MFC SIGNAL FROM OUTGOING CIRCUIT . . 1005.135 80AH - ERRONEOUS MFC SIGNAL FROM INCOMING CIRCUIT . . . 1015.136 80BH - NO B-NUMBERS TO SEND TO OUTGOING CIRCUIT. . . . . . 1015.137 80CH - UNKNOWN DECADIC SIGNAL FROM INCOMING CIRCUIT. 1025.138 80DH - OUTGOING CIRCUIT OUT OF ORDER . . . . . . . . . . . . . . . . . 1025.139 80EH - INCOMING CIRCUIT OUT OF ORDER . . . . . . . . . . . . . . . . . . 1035.140 80FH - CIRCUIT CONGESTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1035.141 810H - FACILITY NOT SUPPORTED . . . . . . . . . . . . . . . . . . . . . . . . . 1045.142 811H - NETWORK FAILURE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1045.143 813H - SWITCHING EQUIPMENT CONGESTION . . . . . . . . . . . . . . . 1055.144 814H - CIRCUIT GROUP CONGESTION . . . . . . . . . . . . . . . . . . . . . . 1055.145 815H - ACCESS BARRED TO THE CALLED SUBSCRIBER . . . . . . . 1065.146 816H - CALL FAILED, SEND SPECIAL INFORMATION TONE . . . . . 1065.147 817H - NETWORK, UNALLOCATED NUMBER. . . . . . . . . . . . . . . . . . 1075.148 818H - NETWORK, LINE OUT OF SERVICE . . . . . . . . . . . . . . . . . . . 1075.149 819H - NETWORK, SUBSCRIBER NUMBER CHANGED. . . . . . . . . . 1085.150 81AH - CONGESTION IN TERMINAL EXCHANGE. . . . . . . . . . . . . . . 1095.151 81DH - CONGESTION IN INTERNATIONAL CALL . . . . . . . . . . . . . . . 1095.152 81EH - CONTROLLED NOT READY . . . . . . . . . . . . . . . . . . . . . . . . . . 1105.153 81FH - NETWORK, OVERLOAD CONGESTION . . . . . . . . . . . . . . . . 1105.154 820H - NETWORK MESSAGE CONTENT ERROR. . . . . . . . . . . . . . . 1115.155 821H - INVALID TRANSIT NETWORK SELECTION . . . . . . . . . . . . . . 111
DN078927Issue 1-0
7
DX200 Clear Code List
Id:0900d80580635bef
5.156 822H - RECOVERY ON TIMER EXPIRY . . . . . . . . . . . . . . . . . . . . . . 1125.157 824H - PCM FAULTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1125.158 828H - CONGESTION FROM NATIONAL NETWORK. . . . . . . . . . . . 1135.159 829H - DIGITAL CIRCUIT MULTIPLICATION EQUIPMENT CONGES-
TION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1145.160 830H - NUMBER PORTABILITY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1145.161 832H - ROUTING ERROR. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1155.162 833H - DIGITAL CIRCUIT MULTIPLICATION EQUIPMENT FAILURE 1165.163 851H - TRAFFIC TO CONGESTED DESTINATION POINT CODE RE-
STRICTED BY SIGNALLING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1165.164 900H - NO MF FORWARD SIGNAL . . . . . . . . . . . . . . . . . . . . . . . . . . 1175.165 901H - TOO LONG MF FORWARD SIGNAL . . . . . . . . . . . . . . . . . . . 1175.166 905H - TOO LONG MF BACKWARD SIGNAL . . . . . . . . . . . . . . . . . . 1185.167 90CH - PREMATURE ACKNOWLEDGEMENT TO SEIZURE IN OUTGO-
ING CIRCUIT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1195.168 90EH - PREMATURE ANSWER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1195.169 90FH - ANSWER AFTER B BUSY . . . . . . . . . . . . . . . . . . . . . . . . . . . 1205.170 A01H - CLEARED FORWARD (SEIZING ACKNOWLEDGED SIGNAL
MISSING) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1205.171 A02H - INVALID MESSAGE FROM TRUNK CIRCUIT . . . . . . . . . . . . 1215.172 A03H - INTERWORKING FAILED. . . . . . . . . . . . . . . . . . . . . . . . . . . . 1215.173 A04H - TRUNK CIRCUIT PROTOCOL ERROR . . . . . . . . . . . . . . . . . 1225.174 A05H - CIRCUIT RELEASED BY CO-EXCHANGE . . . . . . . . . . . . . . 1225.175 A07H - CALL FAILURE FROM OUTGOING CIRCUIT . . . . . . . . . . . . 1235.176 A08H - INTER-EXCHANGE SIGNALLING OUT OF ORDER . . . . . . . 1235.177 A09H - ADDRESS COMPLETE MESSAGE TIME-OUT . . . . . . . . . . . 1245.178 A0AH - ADDRESS COMPLETE MESSAGE SENDING TIME EXCEEDED
1255.179 A0CH - NO DIGITAL TRUNK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1255.180 A0DH - NO ROUTE TO SPECIFIED TRANSIT OR TO DESTINATION . .
1265.181 A0EH - NO CIRCUIT AVAILABLE IN TRANSIT NETWORK. . . . . . . . 1265.182 A0FH - RESELECTION IN TRANSIT NETWORK APPLYING LOAD
SHARING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1275.183 B02H - TRANSIT/TERMINAL SIGNAL WAIT TIME SUPERVISION EX-
CEEDED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1285.184 B0FH - LENGTH OF CHANGED CALLED SUBSCRIBER NUMBER EX-
CEEDED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1285.185 B11H - MODEM COMMUNICATION ERROR. . . . . . . . . . . . . . . . . . . 1295.186 B17H - ADDRESS INCOMPLETE. . . . . . . . . . . . . . . . . . . . . . . . . . . . 1295.187 B18H - SERVICE UNAVAILABLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1305.188 B19H - SERVICE INCOMPATIBLE . . . . . . . . . . . . . . . . . . . . . . . . . . . 1305.189 B20H - NETWORK ADDRESS EXTENSION (NAE) ERROR . . . . . . . 1315.190 B21H - DTE IS UNCONTROLLED . . . . . . . . . . . . . . . . . . . . . . . . . . . 1315.191 B23H - DUAL SEIZURE FROM BIDIRECTIONAL CIRCUIT. . . . . . . . 1325.192 B2AH - BLOCKING RECEIVED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1325.193 B2BH - PARAMETER DOES NOT EXIST OR IS NOT IMPLEMENTED .
133
8 DN078927Issue 1-0
DX200 Clear Code List
Id:0900d80580635bef
5.194 B2CH - INTELLIGENT NETWORK APPLICATION PROTOCOL ERROR.133
5.195 B2DH - INTELLIGENT NETWORK APPLICATION RESPONSE TIME-OUT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134
5.196 B2EH - MAXIMUM NUMBER OF TRIGGERING EVENTS IN A CALL HAS BEEN REACHED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135
5.197 B2FH - TCAP ERROR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1355.198 B30H - ASN1 CODING OR DECODING ERROR . . . . . . . . . . . . . . . . 1365.199 B31H - SELECTIVE CALL CONGESTION HAS PREVENTED CALL AT-
TEMPT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1365.200 B32H - CALL RELEASE ORDERED BY INTELLIGENT NETWORK AP-
PLICATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1375.201 B33H - CONTINUITY CHECK FAILURE . . . . . . . . . . . . . . . . . . . . . . . 1375.202 B34H - A-NUMBER IS NOT THE REGISTERED NUMBER OF AN INDI-
RECT SUBSCRIBER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1385.203 B35H - TOO MANY FRAUDULENT ATTEMPTS TO USE CALLING CARD
1385.204 B36H - CALLING CARD NUMBER SELECTED BY USER NOT FOUND .
1395.205 B37H - IN-SERVICE INTERRUPTED FOR SUSPECTED FRAUD . . . 1405.206 B38H - IN FALLBACK CODE ONE. . . . . . . . . . . . . . . . . . . . . . . . . . . . 1405.207 B39H - IN FALLBACK CODE TWO . . . . . . . . . . . . . . . . . . . . . . . . . . . 1415.208 B3AH - IN FALLBACK CODE THREE . . . . . . . . . . . . . . . . . . . . . . . . . 1415.209 B3BH - IN FALLBACK CODE FIVE . . . . . . . . . . . . . . . . . . . . . . . . . . . 1425.210 B3CH - IN FALLBACK CODE FOUR . . . . . . . . . . . . . . . . . . . . . . . . . . 1435.211 B3DH - IN DIALOG - ROUTING FAILURE IN SS7 NETWORK . . . . . . 1435.212 C00H - DIAL WAIT TIME EXCEEDED . . . . . . . . . . . . . . . . . . . . . . . . . 1445.213 C01H - PROHIBITED DIALLING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1445.214 C02H - INSUFFICIENT DIALLING FROM SUBSCRIBER SIGNALLING. .
1455.215 C04H - CALLING SUBSCRIBER HAS DIALLED WRONG KEYWORD. . .
1465.216 C05H - CALLING SUBSCRIBER HAS NO RIGHT TO FACILITY . . . . 1465.217 C06H - CALLING SUBSCRIBER HAS NO RIGHT TO STORE NUMBER.
1475.218 C08H - PREMATURE DIALLING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1475.219 C09H - SERVICE OR FACILITY ACTIVATION RESTRICTED . . . . . . 1485.220 C0AH - SERVICE OR FACILITY USAGE RESTRICTED. . . . . . . . . . . 1495.221 C0BH - INCONSISTENCY BETWEEN A- AND B-SUBSCRIBERS . . . 1495.222 C0DH - BEARER CAPABILITY NOT PRESENTLY AVAILABLE . . . . . 1505.223 D00H - SUBSCRIBER SIGNALLING MESSAGE CONTENT ERROR 1505.224 D01H - SUBSCRIBER SIGNALLING MESSAGE FORMAT ERROR. . 1515.225 D03H - SERVICE OR FUNCTION NOT IMPLEMENTED . . . . . . . . . . 1515.226 D04H - SUBSCRIBER SIGNALLING PROTOCOL ERROR . . . . . . . . 1525.227 D06H - AOCC CHARGING ERROR. . . . . . . . . . . . . . . . . . . . . . . . . . . 1525.228 D07H - NO RESPONSE TO CALL ESTABLISHMENT: ALERTING OR
CONNECT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1535.229 D08H - GSM ERH 4.08 PROTOCOL TIMER EXPIRES. . . . . . . . . . . . 1545.230 D0BH - DUAL LOG-IN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 154
DN078927Issue 1-0
9
DX200 Clear Code List
Id:0900d80580635bef
5.231 D0FH - ISDN-SUBSCRIBER FACILITY DIALLING REJECTED. . . . . 1555.232 D10H - MANDATORY INFORMATION ELEMENT MISSING . . . . . . . 1555.233 D11H - INVALID INFORMATION ELEMENT CONTENT . . . . . . . . . . 156
6 Clear code index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 157
Glossary. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 164
10 DN078927Issue 1-0
DX200 Clear Code List
Id:0900d80580635beb
Summary of changes
Summary of changesChanges between document issues are cumulative. Therefore, the latest document issue contains all changes made to previous issues.
Changes made between issues 11 and 10Chapters Effective and ineffective clear codes, Clear codes and Clear code index
Added codes 0821H and 0C0DH.
Changes made between issues 10 and 9Chapters Effective and ineffective clear codes, Clear codes and Clear code index
Added clear codes: 0012H, 0030H, 0031H, 0252H, 040BH, 070BH, 071CH, 071DH, 0832H, 0833H, 0A0EH, 0A0FH and 0B11H
Chapter Clear codes
Modified clear codes: 0719H, the default effect of the clear code has been changed.
Changes made between issues 9 and 8Chapters Effective and ineffective clear codes, Clear codes and Clear code index
Added clear codes: 0025H, 0216H, 0217H, 0218H, 0219H, 0220H, 050EH, 0710H, 081EH and 0830H
DN078927Issue 1-0
11
DX200 Clear Code List Introduction
Id:0900d80580635beb
1 IntroductionThe DX 200 Clear Code List contains descriptions of all clear codes sent from the call control program blocks to the statistical process. This manual also describes the use of the clear codes in the DX 200 system.
Clear codes have been given hexadecimal numbers from 0000H to 0FFFH.
Clear codes have been divided into four main classes:
• 0000H - 03FFH: normal clearing • 0400H - 07FFH: internal congestion • 0800H - 0BFFH: external congestion • 0C00H - 0FFFH: subscriber errors
The main class 'normal clearing' consists of clear codes which have not been caused by error in the network element or by subscriber error, but which nevertheless lead to clearing of a call or to an interruption in call set-up.
The class has been further divided into four subclasses
• 0000H - 00FFH: normal clearing / normal clearing: normal clearing situations, for example, subscriber busy
• 0100H - 01FFH: normal clearing / internal congestion: clear codes set by charging and statistics and not leading to a release
• 0200H - 02FFH: normal clearing / external congestion: normal clearing situations, caused by a congestion outside the network element, for example, by a congestion on the radio path
• 0300H - 03FFH: normal clearing / subscriber error: normal congestion caused by the subscriber's facility or equipment.
. The second main class, 'internal congestion' (0400H - 07FFH) consists of cases in which a call or call set-up is interrupted because of an error in the originating exchange. Primarily, the class contains clear codes associated with communication between the various units and program blocks of the exchange and those associated with handling of files.
The third main class, 'external congestion' (0800H -0BFFH) includes all the cases in which a call or call set-up is interrupted because of an error outside the originating exchange. This group consists mainly of clear codes related to inter-exchange signal-ling.
The fourth main class, 'subscriber errors' (0C00H - 0FFFH) includes the cases in which a call or call set-up is interrupted by a calling subscriber's error or by a failure in the sub-scriber's equipment or by faulty subscriber signalling.
The clear codes are transferred from the call control to the statistical system in the fol-lowing messages:
• charging • facility charging (facility control) • call set-up interrupted • call interrupted
The clear codes affect both the tasks and outputs of the following system blocks and program blocks:
• Call Control (CLCSYB)
12 DN078927Issue 1-0
DX200 Clear Code List
Id:0900d80580635beb
Introduction
• Signalling Services (SGLSYB • Statistical Program Block (STPROC) • Charging Program Block (CGPROC) • Charging Control Program Block (CGLSTA) • Text Forming Program Block (TEXTPR) • Traffic Measurement Program Block (TRAMNT) • Traffic Measurement MML (TRMSNT) • Traffic Observation MML (TROBSN)
DN078927Issue 1-0
13
DX200 Clear Code List Use of clear codes
Id:0900d80580635beb
2 Use of clear codesThe individual clear codes or clear code groups are utilized in the following functions of the DX 200 system:
• traffic observation • traffic measurement • traffic maintenance supervision • detailed charging • field reporting • load observation
A more detailed description of these functions follows.
2.1 Traffic observationTraffic observation uses individual clear codes. In two observation categories, that is, in destination observation and in the observation of failed calls, the observation can be limited to a certain clear code, for example, 0804H, or to a certain clear code range, for example, 0400H - 07FFH. This means that traffic observation reports are given only on calls that fall into the defined category. In other observation categories, clear codes have no function.
2.2 Traffic measurementTraffic measurement uses the main classes of clear codes.
2.3 Maintenance supervisionSupervision of the error ratio of circuit groups and control units is part of the mainte-nance supervision. Here, it is important to distinguish between 'normal clearing' and 'clearing due to error', irrespective of the cause of error.
2.4 Detailed chargingIndividual clear codes received in the charging messages and facility charging messages are significant for detailed charging.
2.5 Field reportingIndividual clear codes and the classification of clear codes in the Service Level File of the statistics system are used in field reporting.
The Service Level File can be defined to include eight code groups, which may comprise any clear codes (0000H - 0FFFH). The number of occurrences of the clear codes belonging to these groups are updated, group by group, to the Service Level File. The occurrences of each clear code are also registered in the Service Level File.
14 DN078927Issue 1-0
DX200 Clear Code List
Id:0900d80580635beb
Presentation of clear codes
3 Presentation of clear codesClear codes have been described in numerical order. The description is given in the fol-lowing form.
Number The hexadecimal number of the clear code (0000H -0FFFH).
Name The name of the clear code.
Text in MML printouts The name of the clear code in the MML programs.
Description A description of the clear code.
Detected by The name of the program block that detects the clear code. Description of the situation which causes the clear code to be set.
Default effect on the exchange A description of the effects that the clear code has on the exchange
Possibility to change the default effect This field states whether it is possible to change the default effect.
Alarms A list of possible alarms which are set when the clear code occurs in the exchange.
DN078927Issue 1-0
15
DX200 Clear Code List Effective and ineffective cause codes
Id:0900d80580635beb
4 Effective and ineffective cause codesThe operator can use clear codes when generating charging. In the list below, effective clear codes are those codes that can be generated when a call reaches conversation state. Ineffective clear codes indicate that the call did not reach conversation state. However, ineffective clear codes are important statistically.
List of effective and ineffective clear codes:
NUMBER NAME OF CLEAR CODE
0000H NORMAL END OF CALL
0001H SUSPENDED CALL
0003H CALL DURATION BELOW SUPERVISION TIME
0004H B BUSY OR CONGESTION RECEIVED FROM OUTGOING CIRCUIT
0005H CALLED SUBSCRIBER BUSY
0006H TIME-OUT FOR B-SUBSCRIBER ANSWER
0007H CALL WAITING TIME-OUT
0008H CALLED SUBSCRIBER NOT CONNECTED
0009H CALL ALREADY WAITING
000AH INTERVENTION ALREADY ON
000BH REROUTING DUE TO B-SUBSCRIBER FACILITY
000CH OUTGOING DIRECTION RESTRICTED DUE TO
000EH MALICIOUS CALL TRACING
000FH INTERMEDIATE CHARGING
0010H ABSENT SUBSCRIBER
0011H OPERATOR PRIORITY ACCESS
0012H NO PAGING RESPONSE
0013H CALL TRANSFER RECALL DUE TO C-SUBSCRIBER
0015H NORMAL UNSPECIFIED
0016H SUBSCRIBER'S CHARGING CAPACITY EXCEEDED IN THE EXCHANGE
0020H ANNOUNCEMENT SUCCESS IN INTERCEPTION
0025H CALL DROP BACK RELEASE
0030H USER CREDIT LIMIT REACHED
0031H NOT ENOUGH CREDIT TO CALL
0100H CIRCUIT RE-SEIZED
0101H CIRCUIT RELEASED BEFORE 'END OF THE CALL'
0102H CALL RECORD RELEASED DURING CALIBRATION
0103H CHARGING IN WRONG PHASE OF CALL
0201H CALL RELEASED
0202H CLEAR REQUEST RECEIVED FROM OUTGOING CIRCUIT
0203H B-CHANNEL UNACCEPTABLE
16 DN078927Issue 1-0
DX200 Clear Code List
Id:0900d80580635beb
Effective and ineffective cause codes
0204H ESTABLISHED B-CHANNEL
0206H CALL REJECTED
0207H SUBSCRIBER CONGESTION
020BH CLEAR IN DETAILED CHARGING
020EH CALLING SUBSCRIBER LINE VACANT OR OUT OF SERVICE
020FH CHANGE OF OUTGOING CIRCUIT
0210H NULL NUP
0211H NETWORK, REJECTED DIVERTED CALLS
0213H NETWORK, USER NOT IN CUG
0215H CALL DROP BACK
0216H MISDIALLED TRUNK PREFIX
0217H TEMPORARY OUT OF ORDER
0218H OUT OF CATCHMENT AREA
0219H TRANSLATION OUT-OF-SERVICE
0220H ANONYMOUS CALLS REJECTION
0252H UNTERMINATED CALL TO A PORTED NUMBER
0300H CALLING SUBSCRIBER BARRED DUE TO RESTRICTION IN THE OUTGOING DIRECTION
0301H CALLING SUBSCRIBER'S OUTGOING CALL RESTRICTED BY OPERATOR
0304H CALLED SUBSCRIBER LINE OUT OF SERVICE
0305H CALLED SUBSCRIBER LINE FAULTY
0306H ACCESS TO B-SUBSCRIBER LINE RESTRICTED
0307H B-NUMBER UNUSED
0308H B-NUMBER CHANGED
0309H TIME-OUT WHEN WAITING FOR OPERATOR'S INTERVENTION
030AH CLEAR/CALLING SUBSCRIBER HAS MADE ONHOOK DURING SET-UP PHASE
030BH CLEAR/CALLING SUBSCRIBER HAS MADE ONHOOK WHEN WAITING FOR ANSWER
030CH REANSWER TIME OUT
030DH B- OR C-NUMBER IS NOT REGISTERED
030EH CALLED SUBSCRIBER LINE BLOCKED
030FH CHANGE IN NUMBERING PLAN
0310H CLOSED USER GROUP RESCTRICTION
0311H BEARER SERVICE NOT PROVIDED
0312H TELESERVICE NOT PROVIDED
0315H CALLED SUBSCRIBER HAS CALL DIVERSION BARRING
0317H TIME-OUT IN INTELLIGENT NETWORK BASED
031AH INCOMING CALLS BARRED WITHIN THE CUG
DN078927Issue 1-0
17
DX200 Clear Code List Effective and ineffective cause codes
Id:0900d80580635beb
031CH SUBSCRIBER NOT A MEMBER OF THE CUG
031DH OUTGOING CALLS BARRED WITHIN THE CUG
0321H NO CUG SELECTED
0322H UNKNOWN CUG INDEX
0400H ATTENUATOR CONGESTION
0401H INTERWORKING UNIT CONGESTION
0402H REGISTER TOTAL TIME EXCEEDED
0403H MFCU DEVICE CONGESTION
0404H PBRU DEVICE CONGESTION
0405H ERRONEOUS SERVICE REQUEST FROM C0-PROCESS
0406H CONNECTION FAILED IN GSW/SWI
0407H ERRONEOUS ANSWER FROM PARTNER PROGRAM BLOCK
0408H LENGTH OF CALLED SUBSCRIBER NUMBER EXCEEDED
0409H CONNECTION FAILED IN SSW/SWI
040AH CIRCUIT CONGESTION DUE TO TRAFFIC TYPE
040BH HOP COUNTER EXHAUST
0506H LINES OF LINE HUNTING GROUPS BARRED
0508H CHARGING ERROR
0509H FILE ERROR
050BH MODULE ROUTE OR SSW CONGESTION
050CH MFC-ASS-CHANNEL CLOSING MISSED
050DH FACILITY CONTROL FAILED
050EH UPDATE LOG BLOCKING
050FH UNSUITABLE MODULE CIRCUIT
0600H FILE RECORD CONGESTION
0601H MODULE OR V5 CONGESTION
0602H REGISTER CONGESTION
0603H NO RESPONSE FROM PARTNER PROGRAM BLOCK
0604H INTERNAL CALL LINK CONGESTION
0606H CONFERENCE DEVICE CONGESTION
0607H POLARITY REVERSAL FAILURE
0608H CHARGING NOT STARTED
0609H CALL CLEARED BY MML
060BH OVERLOAD CONGESTION
060DH STAGE CIRCUIT CONGESTION
060EH UNIT RESTARTED
060FH SUBSCRIBER MODULE OR V5 INTERFACE FAILURE, CALL CLEARED
0700H LONG AON REQUEST
18 DN078927Issue 1-0
DX200 Clear Code List
Id:0900d80580635beb
Effective and ineffective cause codes
0701H REGISTER ANALYSIS FAILED
0702H QUEUEING TIME EXCEEDED
0704H PARITY ERROR FROM PBRU/MFCU DEVICE
0705H MODULE OR V5 INTERFACE NOT AVAILABLE
0706H CALL INTERRUPTED DURING REGISTER ANALYSIS
0707H SUBSCRIBER MODULE RESTARTED
070AH FORCED CLEAR OF A CALL
070BH MODEM ERROR
070CH OVERLOAD CONTROL SYSTEM ERROR
070DH ANNOUNCEMENT SERVICE FAILURE
070EH CONFIGURATION ERROR
0710H NO ANALYSIS FOR CARRIER ACCESS CODE
0711H TARIFF NOT ACCEPTED BY TRANSIT EXCHANGE
0712H TARIFF NOT ACCEPTED BY ORIGINATING OR INTERWORKING EXCHANGE
0713H NO ISUP ROUTE
0714H ATTRIBUTE DIRECTED ROUTING MISMATCH
0715H REQUESTED FACILITY WAS NOT AVAILABLE ON THE OUTGOING ROUTE
0716H REQUESTED BEARER CAPABILITY COULD NOT BE FULFILLED ON THE ROUTE
0718H DIGIT ANALYSIS IN CENTRAL MEMORY RESULTED IN CONGES-TION
0719H NO RESOURCE AVAILABLE FOR CALL
071AH IDENTIFIED CHANNEL NOT EXIST
071BH REQUESTED CHANNEL NOT AVAILABLE
071CH PACKET CONTROL UNIT CONGESTION
071DH POINT-TO-POINT PROTOCOL ERROR
0801H LENGTH OF ORIGINAL CALLED SUBSCRIBER EXCEEDED
0802H LENGTH OF CALLING SUBSCRIBER NUMBER EXCEEDED
0803H INVALID CALLING SUBSCRIBER CATEGORY
0804H OUTGOING CIRCUIT CONGESTION
0806H IDENTITY OF CALLING SUBSCRIBER IS NOT AVAILABLE
0807H WAITING TIME FOR MFC PAUSE SIGNAL EXCEEDED
0808H WAITING TIME FOR MFC BACKWARD SIGNAL EXCEEDED
0809H ERRONEOUS MFC SIGNAL FROM OUTGOING CIRCUIT
080AH ERRONEOUS MFC SIGNAL FROM INCOMING CIRCUIT
080BH NO B-NUMBERS TO SEND TO OUTGOING CIRCUIT
080CH UNKNOWN DECADIC SIGNAL FROM INCOMING
080DH OUTGOING CIRCUIT OUT OF ORDER
DN078927Issue 1-0
19
DX200 Clear Code List Effective and ineffective cause codes
Id:0900d80580635beb
080EH INCOMING CIRCUIT OUT OF ORDER
080FH CIRCUIT CONGESTION
0810H FACILITY NOT SUPPORTED
0811H NETWORK FAILURE
0813H SWITCHING EQUIPMENT CONGESTION
0814H CIRCUIT GROUP CONGESTION
0815H ACCESS BARRED TO THE CALLED SUBSCRIBER
0816H CALL FAILED, SEND SPECIAL INFORMATION TONE
0817H NETWORK, UNALLOCATED NUMBER
0818H NETWORK, LINE OUT OF SERVICE
0819H NETWORK, SUBSCRIBER NUMBER CHANGED
081AH CONGESTION IN TERMINAL EXCHANGE
081DH CONGESTION IN INTERNATIONAL CALL
081EH CONTROLLED NOT READY
081FH NETWORK, OVERLOAD CONGESTION
0820H NETWORK MESSAGE CONTENT ERROR
0821H INVALID TRANSIT NETWORK SELECTION
0822H RECOVERY ON TIMER EXPIRY
0824H PCM FAULTY
0828H CONGESTION FROM NATIONAL NETWORK
0829H DIGITAL CIRCUIT MULTIPLICATION EQUIPMENT CONGESTION
0830H NUMBER PORTABILITY
0832H ROUTING ERROR
0833H DIGITAL CIRCUIT MULTIPLICATION EQUIPMENT FAILURE
0851H TRAFFIC TO CONGESTED DESTINATION POINT
0900H NO MF FORWARD SIGNAL
0901H TOO LONG MF FORWARD SIGNAL
0905H TOO LONG MF BACKWARD SIGNAL
090CH PREMATURE ACKNOWLEDGEMENT TO SEIZURE IN OUTGOING CIRCUIT
090DH WAITING TIME FOR ACKNOWLEDGEMENT TO SEIZURE IN OUTGOING CIRCUIT EXCEEDED
090EH PREMATURE ANSWER
090FH ANSWER AFTER B BUSY
0A01H CLEARED FORWARD (SEIZING ACKNOWLEDGED SIGNAL MISSING)
0A02H INVALID MESSAGE FROM TRUNK CIRCUIT
0A03H INTERWORKING FAILED
0A04H TRUNK CIRCUIT PROTOCOL ERROR
0A05H CIRCUIT RELEASED BY CO-EXCHANGE
20 DN078927Issue 1-0
DX200 Clear Code List
Id:0900d80580635beb
Effective and ineffective cause codes
0A07H CALL FAILURE FROM OUTGOING CIRCUIT
0A08H INTER-EXCHANGE SIGNALLING OUT OF ORDER
0A09H ADDRESS COMPLETE MESSAGE TIME-OUT
0A0AH ADDRESS COMPLETE MESSAGE SENDING TIME EXCEEDED
0A0CH NO DIGITAL TRUNK
0A0DH NO ROUTE TO SPECIFIED TRANSIT OR TO DESTINATION
0A0EH NO CIRCUIT AVAILABLE IN TRANSIT NETWORK
0A0FH RESELECTION IN TRANSIT NETWORK APPLYING LOAD SHARING
0B02H TRANSIT/TERMINAL SIGNAL WAIT TIMERSUPERVISION EXCEEDED
0B0FH LENGTH OF CHANGED CALLED SUBSCRIBER NUMBER EXCEEDED
0B11H MODEM COMMUNICATION ERROR
0B17H ADDRESS INCOMPLETE
0B18H SERVICE UNAVAILABLE
0B19H SERVICE INCOMPATIBLE
0B20H NETWORK ADDRESS EXTENSION (NAE) ERROR
0B21H DTE IS UNCONTROLLED
0B23H DUAL SEIZURE FROM BIDIRECTIONAL CIRCUIT
0B2AH BLOCKING RECEIVED
0B2BH PARAMETER DOES NOT EXIST OR IS NOT IMPLEMENTED
0B2DH INTELLIGENT NETWORK APPLICATION RESPONSE
0B2CH INTELLIGENT NETWORK APPLICATION PROTOCOL ERROR TIME-OUT
0B2EH MAXIMUM NUMBER OF TRIGGERING EVENTS IN A CALL HAS BEEN REACHED
0B2FH TCAP ERROR
0B30H ASN1 CODING OR DECODING ERROR
0B31H SELECTIVE CALL CONGESTION HAS PREVENTED CALL ATTEMPT
0B32H CALL RELEASE ORDERED BY INTELLIGENT NETWORK APPLI-CATION
0B33H CONTINUITY CHECK FAILURE
0B34H A-NUMBER IS NOT THE REGISTERED NUMBER OF AN INDIRECT SUBSCRIBER
0B35H TOO MANY FRAUDULENT ATTEMPTS TO USE CALLING CARD
0B36H CALLING CARD NUMBER SELECTED BY USER NOT FOUND
0B37H IN-SERVICE INTERRUPTED FOR SUSPECTED FRAUD
0B38H IN FALLBACK CODE ONE
0B39H IN FALLBACK CODE TWO
0B3AH IN FALLBACK CODE THREE
DN078927Issue 1-0
21
DX200 Clear Code List Effective and ineffective cause codes
Id:0900d80580635beb
0B3BH IN FALLBACK CODE FIVE
0B3CH IN FALLBACK CODE FOUR
0B3DH IN DIALOG - ROUTING FAILURE IN SS7 NETWORK
0C00H DIAL WAIT TIME EXCEEDED
0C01H PROHIBITED DIALLING
0C02H INSUFFICIENT DIALLING FROM SUBSCRIBER SIGNALLING
0C04H CALLING SUBSCRIBER HAS DIALLED WRONG KEYWORD
0C05H CALLING SUBSCRIBER HAS NO RIGHT TO FACILITY
0C06H CALLING SUBSCRIBER HAS NO RIGHT TO STORE NUMBER
0C08H PREMATURE DIALLING
0C09H SERVICE OR FACILITY ACTIVATION RESTRICTED
0C0AH SERVICE OR FACILITY USAGE RESTR USED
0C0BH INCONSISTENCY BETWEEN A- AND B-SUBSCRIBERS
0C0DH BEARER CAPABILITY NOT PRESENTLY AVAILABLE
0D00H SUBSCRIBER SIGNALLING MESSAGE CONTENT
0D01H SUBSCRIBER SIGNALLING MESSAGE FORMAT ERROR
0D03H SERVICE OR FUNCTION NOT IMPLEMENTED
0D04H SUBSCRIBER SIGNALLING PROTOCOL ERROR
0D06H AOCC CHARGING ERROR
0D07H NO RESPONSE TO CALL ESTABLISHMENT ALERTING OR CONNECT
0D08H GSM ERH 4.08 PROTOCOL TIMER EXPIRES
0D0BH DUAL LOG-IN
0D0FH ISDN-SUBSCRIBER FACILITY DIALLING REJECTED
0D10H MANDATORY INFORMATION ELEMENT MISSING
0D11H INVALID INFORMATION ELEMENT CONTENT
22 DN078927Issue 1-0
DX200 Clear Code List
Id:0900d80580635beb
Clear codes
5 Clear codes
5.1 000H - NORMAL END OF CALL
Text in MML printoutsNORMAL END OF CALL
DescriptionAn outgoing or incoming call has ended faultlessly.
Detected by-
Default effect on the exchangeDepending on the method of clearing, the call is cleared when either subscriber, or both of them have made onhook.
Possibility to change the default effectNot possible.
AlarmsNo alarms.
5.2 001H - SUSPENDED CALL
Text in MML printoutsSUSPENDED CALL
DescriptionAs the result of the digit analysis, the call set-up is returned to the incoming circuit.
Detected by
Default effect on the exchangeThe call is cleared in terminal and transit exchanges. The originating exchange connects a special information tone to the subscriber.
Possibility to change the default effectNot possible.
Program block
Explanation
INREGI INREGI sets the clear code when the answer to the digit analysis is rou_and_cha_suspended_call.
DN078927Issue 1-0
23
DX200 Clear Code List Clear codes
Id:0900d80580635beb
AlarmsNo alarms.
5.3 003H - CALL DURATION BELOW SUPERVISION TIME
Text in MML printoutsCALL DURAT BELOW SUP TIME
DescriptionThe call has ended before the set limit. This serves to itemize the fault cases in which the called subscriber has answered and the call was successful as concerns the exchange, but the established connection did not satisfy the calling and called subscrib-ers.
Detected by-
Default effect on the exchangeThe call is cleared in transit exchanges. The originating exchange connects a special information tone to the subscriber.
Possibility to change the default effectNot possible.
AlarmsNo alarms.
5.4 004H - B BUSY OR CONGESTION RECEIVED FROM OUTGOING CIRCUIT
Text in MML printoutsB BUSY OR CONGESTION
DescriptionLine signal B BUSY (called subscriber busy) or CONGESTION has been received from the outgoing circuit.
Detected by-
Default effect on the exchangeThe call is cleared in transit exchanges. The originating exchange connects a busy tone to the subscriber.
Possibility to change the default effectNot possible.
24 DN078927Issue 1-0
DX200 Clear Code List
Id:0900d80580635beb
Clear codes
AlarmsNo alarms.
5.5 005H - CALLED SUBSCRIBER BUSY
Text in MML printoutsB-SUBSCRIBER BUSY
DescriptionThe called subscriber line is busy, or the outgoing circuit has sent a register signal or a line signal which has been interpreted as "called subscriber busy", or the outgoing circuit has sent a "B SUBSCRIBER BUSY" message, or a clearing message where the cause code is "B BUSY". This clear code prevents Call Forwarding Busy (CFB) if the called subscriber rejects a call (or a waiting call) during the ringing phase.
Detected by
Default effect on the exchangeThe call is cleared in terminal and transit exchanges. The originating exchange connects a busy tone to the subscriber. Some subscriber services, e.g. Operator Intervention, may cause that the call set-up is continued.
Possibility to change the default effectUsing facility routing (command group RE, parameter CBB), the call can be directed for reanalysis in tree 33H both in terminal and transit exchanges. Besides this, facility routing can be used to connect an audible tone to the incoming circuit in terminal and transit exchanges.
AlarmsNo alarms.
5.6 006H - TIME-OUT FOR B-SUBSCRIBER ANSWER
Text in MML printoutsB ANSWER TIME OUT
DescriptionThe called subscriber's (B-subscriber) answer supervision time has expired, or B DOES NOT ANSWER message or a clearing message with cause code B DOES NOT ANSWER has been received from the outgoing circuit. The clear code prevents Call
Program block
Explanation
SI6PRB SI6PRB sets the clear code when both B-channels are occupied in the sig-nalling, or an analog subscriber is busy.
DN078927Issue 1-0
25
DX200 Clear Code List Clear codes
Id:0900d80580635beb
Forwarding on No Reply (CFNR) if the amount of call forwarding steps has been exceeded.
Detected by
Default effect on the exchangeThe call is cleared in terminal and transit exchanges. The originating exchange connects a busy tone to the subscriber.
Possibility to change the default effectNot possible.
AlarmsNo alarms.
5.7 007H - CALL WAITING TIME-OUT
Text in MML printoutsCALL WAITING TIME OUT
DescriptionA subscriber who has the Call Waiting service has not answered a waiting call within the time supervision. The waiting call is cleared.
Detected by
Default effect on the exchangeThe call is cleared in terminal and transit exchanges. The originating exchange connects a special information tone to the subscriber.
Possibility to change the default effectNot possible.
AlarmsNo alarms.
Program block
Explanation
CASSIG ICxPRB or CASSIG sets the clear code when the supervision time of the called subscriber's answer has been exceeded.
ICXPRB ICXPRB or CASSIG sets the clear code when the supervision time of the called subscriber's answer has been exceeded.
Program block
Explanation
TPSPRB TPSPRB sets the clear code when the subscriber has not answered a waiting call within the time supervision.
26 DN078927Issue 1-0
DX200 Clear Code List
Id:0900d80580635beb
Clear codes
5.8 008H - CALLED SUBSCRIBER NOT CONNECTED
Text in MML printoutsB NOT CONNECTED
DescriptionThe called subscriber line is unallocated or not connected.
Detected by
Default effect on the exchangeThe call is cleared in terminal and transit exchanges. The originating exchange connects a special information tone to the subscriber.
Possibility to change the default effectNot possible.
AlarmsNo alarms.
5.9 009H - CALL ALREADY WAITING
Text in MML printoutsCALL ALREADY WAITING
DescriptionAn attempt has been made to call a subscriber who has currently a call waiting. Another waiting call will not be accepted.
Detected by
Default effect on the exchangeThe call is cleared in terminal and transit exchanges. The originating exchange connects a busy tone to the subscriber.
Possibility to change the default effectNot possible.
Program block
Explanation
OC6PRB OC6PRB sets the clear code when the called subscriber's data reveals that the subscriber line is unallocated or unequipped.
Program block
Explanation
TPSPRB TPSPRB sets the clear code when a call waiting attempt is made to an analog subscriber line with a call already waiting.
DN078927Issue 1-0
27
DX200 Clear Code List Clear codes
Id:0900d80580635beb
AlarmsNo alarms.
5.10 00AH - INTERVENTION ALREADY ON
Text in MML printoutsINTERVENTION ALREADY ON
DescriptionIntervention is attempted to a subscriber line which is already subject to intervention.
Detected by
Default effect on the exchangeThe call is cleared in terminal and transit exchanges. The originating exchange connects a congestion tone to the subscriber.
Possibility to change the default effectNot possible.
AlarmsNo alarms.
5.11 00BH - REROUTING DUE TO B-SUBSCRIBER FACILITY
Text in MML printoutsREROUTING DUE TO B-SUBSC
DescriptionThe called subscriber (B-subscriber) has in active state a facility which directs the call to a third subscriber (C-subscriber) or to a centralized answering device by means of rerouting.
Detected by
Program block
Explanation
TPSPRB TPSPRB sets the clear code when intervention is attempted in a case where the subscriber is already subject to intervention.
Program block
Explanation
OUREGI OUREGI sets the clear code when the call is rerouted due to an absent subscriber service facility, or if no calling subscriber's (A-subscriber) iden-tification data are received from the incoming signalling.
28 DN078927Issue 1-0
DX200 Clear Code List
Id:0900d80580635beb
Clear codes
Default effect on the exchangeThe call is cleared in transit exchanges. The originating exchange connects a special information tone to the subscriber.
Possibility to change the default effectNot possible.
AlarmsNo alarms.
5.12 00CH - OUTGOING DIRECTION RESTRICTED DUE TO CRISIS MODE
Text in MML printoutsRESTRI DUE TO CRISIS MODE
DescriptionThe line signal B BUSY (called subscriber busy) or CONGESTION has been received from the outgoing circuit. The exchange has a "crisis" operating mode on, which prevents the call set-up.
Detected by
Default effect on the exchangeThe call is cleared in terminal and transit exchanges. The originating exchange sends a special information tone to the subscriber.
Possibility to change the default effectNot possible.
AlarmsNo alarms.
5.13 00EH - MALICIOUS CALL TRACING
Text in MML printoutsMALICIOUS CALL
Program block
Explanation
ICXPRB ICxPRB or INREGI sets the clear code when call set-up is prevented on the basis of the restriction category used in the exchange.
INREGI ICxPRB or INREGI sets the clear code when call set-up is prevented on the basis of the restriction category used in the exchange.
DN078927Issue 1-0
29
DX200 Clear Code List Clear codes
Id:0900d80580635beb
DescriptionThe called subscriber has performed call tracing.
Detected by
Default effect on the exchangeAfter call tracing, the call is continued as normal.
Possibility to change the default effectNot possible.
AlarmsNo alarms.
5.14 00FH - INTERMEDIATE CHARGING
Text in MML printoutsINTERMEDIATE CHARGING
DescriptionAn intermediate charging message is sent to the statistics when the amount of charging pulses of an ongoing call, or its duration, has reached the preset limit. The statistical system stores the accumulated charging pulses and the elapsed call time in specific counters. An observation report and a detailed charging record are always generated for calls ending in this clear code, and they are directed to output devices defined by the user.
Detected by
Program block
Explanation
OC6PRB OC6PRB sets the clear code when the called subscriber has performed call tracing.
Program block
Explanation
CASSIG ICxPRB or CASSIG sets the clear code when the length of the call exceeds the time supervision limit set on the intermediate report in the exchange. TIGPRB sets the clear code when the amount of charging pulses exeeds the amount of pulses set on the intermediate report in the exchange.
ICXPRB ICxPRB or CASSIG sets the clear code whenthe length of the call exceeds the time supervision limit set on the intermediate report in the exchange. IGPRB sets the clear code when the amount of charging pulses exeeds the amount of pulses set on the intermediate report in the exchange.
TIGPRB –
30 DN078927Issue 1-0
DX200 Clear Code List
Id:0900d80580635beb
Clear codes
Default effect on the exchangeThe clear code is only used in successful intermediate reporting. No tone is connected to the subscriber, and the call is continued as normal.
Possibility to change the default effectNot possible.
AlarmsNo alarms.
5.15 010H - ABSENT SUBSCRIBER
Text in MML printoutsABSENT SUBSCRIBER
DescriptionThe operation concerns a subscriber who is not registered, unallocated, or not reach-able.
Detected by
Default effect on the exchangeIf, on the basis of incoming signalling information, the call can be rerouted from the incoming exchange, the call control clears the call backwards. The originating exchange carries out a digit re-analysis in standard analysis tree 26H (command group RE, param-eter CAS).
Possibility to change the default effectWith facility routing it is possible to connect an audible tone to the subscriber.
AlarmsNo alarms.
5.16 011H - OPERATOR PRIORITY ACCESS
Text in MML printoutsOPERATOR PRIORITY ACCESS
Program block
Explanation
OC6PRB OC6PRB or OUREGI sets the clear code when the subscriber data of the called subscriber discloses that absent subscriber service is active.
OUREGI OC6PRB or OUREGI sets the clear code when the subscriber data of the called subscriber discloses that absent subscriber service is active.
DN078927Issue 1-0
31
DX200 Clear Code List Clear codes
Id:0900d80580635beb
DescriptionThe call is cleared because of a priority call.
Detected by
Default effect on the exchangeThe call is cleared in terminal and transit exchanges. The originating exchange connects a special information tone to the subscriber.
Possibility to change the default effectNot possible.
AlarmsNo alarms.
5.17 012H - NO PAGING RESPONSE
Text in MML printoutsNO PAGING RESPONSE
DescriptionA mobile-terminating call cannot be connected because the mobile station is not found in paging, or the clear code prevents Call Forwarding On Mobile Subscriber Not Reach-able (CFNRc) due to too many call forwardings.
Detected by-
Default effect on the exchangeThe call is cleared in originating and terminal exchanges. The transit exchange carries out a digit re-analysis in tree 2EH (command group RE, parameter CRO).
Possibility to change the default effectUsing facility routing, the transit exchange can connect an audible tone to the sub-scriber.
AlarmsNo alarms.
5.18 013H - CALL TRANSFER RECALL DUE TO C-SUB-SCRIBER ANSWER TIME-OUT
Program block
Explanation
TPSPRB TPSPRB sets the clear code when the call is cleared because of auto-matic operator's intervention.
32 DN078927Issue 1-0
DX200 Clear Code List
Id:0900d80580635beb
Clear codes
Text in MML printoutsCALL TRANSFER RECALL
DescriptionThe calling subscriber (A-subscriber), who has call transfer with recall facility, has trans-ferred the call to a third party (C-subscriber), but the recall timer (C-subscriber answer-ing time) has expired. The transferred call is cleared and the original call between the A-subscriber (the controlling subscriber) and the B-subscriber is re-established.
Detected by-
Default effect on the exchange–
Possibility to change the default effectNot possible.
AlarmsNo alarms.
5.19 015H - NORMAL UNSPECIFIED
Text in MML printoutsNORMAL UNSPECIFIED
DescriptionFacility call was successful. Time supervision expires in an exchange, which connects an announcement in a failed call. The clear code is sent to the incoming circuit in a clearing message (this is done only in ISUP connections).
Detected by-
Default effect on the exchangeThe call is cleared in transit exchanges. The originating exchange connects a special information tone to the subscriber.
Possibility to change the default effectNot possible.
AlarmsNo alarms.
5.20 016H - SUBSCRIBER'S CHARGING CAPACITY EXCEEDED IN THE EXCHANGE
DN078927Issue 1-0
33
DX200 Clear Code List Clear codes
Id:0900d80580635beb
Text in MML printoutsCHA CAPA OF SUBS EXCEEDED
DescriptionThe charging capacity of a subscriber has been exceeded in the exchange.
Detected by-
Default effect on the exchange–
Possibility to change the default effectNot possible.
AlarmsNo alarms.
5.21 018H - INTERMEDIATE CHARGING IN THE END OF THE PHASE CHARGING
Text in MML printoutsINT CHRG IN PHAS CHRG END
DescriptionA service number call is returned back to the operator. Phase charging is removed and intermediate charging message is sent to the statistics. The call is not cleared with this code, but the code is saved to the CDR
Detected by-
Default effect on the exchange–
Possibility to change the default effectNot possible.
AlarmsNo alarms.
5.22 020H - ANNOUNCEMENT SUCCESS IN INTERCEPTION
Text in MML printoutsANN SUCCESS IN INTERCEPT
34 DN078927Issue 1-0
DX200 Clear Code List
Id:0900d80580635beb
Clear codes
DescriptionIn case of a successful interception announcement, the ICC sets the clear code ANN SUCCESS IN INTERCEPT (0020H) and sends it to statistics and charging. The initial disconnect clear code is always shown in call reports and in the unsuccessful call CDR if it is made.
Detected by
Default effect on the exchangeThe call is cleared. If detailed charging (DC) is set in the interception tree, two clear codes are shown in the Call Detailed Charging report (CDR), the Subscriber Observa-tion report (SO), and the trafficability performance reports. Otherwise only the initial clear code is shown.
Possibility to change the default effectNot possible.
AlarmsNo alarms.
5.23 025H - CALL DROP BACK RELEASE
Text in MML printoutsCALL DROP BACK RELEASE
DescriptionThe call has been released due to the Call Drop Back function or due to the rerouting in call forwarding invoked by the Service Node or Voice Prosessing type of node.
Detected by
Program block
Explanation
ICXPRB Either the IC1PRB, IC3PRB or IC6PRB sets this clear code when the interception announcement is given successfully.
Program block
Explanation
CREPRB The CREPRB program block sets this cause code when it releases the old connection towards the node, which has invoked the Call Drop Back. New connection to the new destination has been established. The ICXPRB program block sets this clear code when call rerouting has occured in the QSIG call forwarding.
ICXPRB The CREPRB program block sets this cause code when it releases the old connection towards the node, which has invoked the Call Drop Back. New connection to the new destination has been established.The ICXPRB program block sets this clear code when call rerouting has occured in the QSIG call forwarding.
DN078927Issue 1-0
35
DX200 Clear Code List Clear codes
Id:0900d80580635beb
Default effect on the exchangeThis clear code is sent forward to the network.
Possibility to change the default effectNot possible.
AlarmsNo alarms.
5.24 031H - NOT ENOUGH CREDIT TO CALL
Text in MML printoutsNOT ENOUGH CREDIT
DescriptionThe calling party does not have enough credit to make a call.
Detected by
Default effect on the exchangeThe originating exchange connects a tone or an announcement defined in EOS-analyse to the subscriber.
Possibility to change the default effectNot possible.
AlarmsNo alarms.
5.25 100H - CIRCUIT RE-SEIZED
Text in MML printoutsCIRCUIT RE-SEIZED
DescriptionWhen a single circuit stays occupied in statistics and the circuit is re-seized, the statistics program block releases the old call record before the new seizure is accepted in the sta-tistics.
Program block
Explanation
TIGPRB TIGPRB sets the code when the calling subscriber does not have enough credit for a call.
36 DN078927Issue 1-0
DX200 Clear Code List
Id:0900d80580635beb
Clear codes
Detected by
Default effect on the exchangeNo effect on the call set-up.
Possibility to change the default effectNo effect on the call set-up.
AlarmsNo alarms.
5.26 101H - CIRCUIT RELEASED BEFORE 'END OF THE CALL' NOTICE
Text in MML printoutsCIRCUIT RELEASE BEF "END"
DescriptionMessages INCOMING CIRCUIT RELEASED' or 'OUTGOING CIRCUIT RELEASED' have been received before the end of the call notice.
Detected by
Default effect on the exchangeNo effect on the call set-up.
Possibility to change the default effectNo effect on the call set-up.
AlarmsNo alarms.
5.27 102H - CALL RECORD RELEASED DURING CALIBRATION
Program block
Explanation
STPROC STPROC sets the clear code when a reserved call record is subject to a new reservation.
Program block
Explanation
CGPROC CGPROC or STPROC sets the clear code when the order of statistics messages in the call is not logical.
STPROC CGPROC or STPROC sets the clear code when the order of statistics messages in the call is not logical.
DN078927Issue 1-0
37
DX200 Clear Code List Clear codes
Id:0900d80580635beb
Text in MML printoutsCALL RECORD REL DURING CA
DescriptionWhen calibrating the traffic measurement files, the statistical program block has detected a circuit which is not included in the marker files even though the statistics files indicate that the circuit is seized. The statistics system releases the circuit.
Detected by-
Default effect on the exchangeNo effect on the call set-up.
Possibility to change the default effectNo effect on the call set-up.
AlarmsNo alarms.
5.28 103H - CHARGING IN WRONG PHASE OF CALL
Text in MML printoutsCHARGING IN WRONG PHASE
DescriptionThe statistical program block has received a charging message for a call in a phase where the message cannot be accepted.
Detected by-
Default effect on the exchangeNo effect on the call set-up.
Possibility to change the default effectNo effect on the call set-up.
AlarmsNo alarms.
5.29 201H - CALL RELEASED
Text in MML printoutsCALL RELEASED
38 DN078927Issue 1-0
DX200 Clear Code List
Id:0900d80580635beb
Clear codes
DescriptionThe outgoing signalling has received an unknown line signal or an unknown message in reply to the seizure.
Detected by
Default effect on the exchangeThe call is cleared in terminal and transit exchanges. The originating exchange connects a congestion tone to the subscriber.
Possibility to change the default effectNot possible.
AlarmsNo alarms.
5.30 202H - CLEAR REQUEST RECEIVED FROM OUTGOING CIRCUIT
Text in MML printoutsCLEAR REQUEST RECEIVED
DescriptionA clear request or an equivalent signal or message has been received from the outgoing circuit. A call in the call phase is cleared.
Detected by
Default effect on the exchangeThe call is cleared in terminal and transit exchanges. The originating exchange sends a special information tone to the subscriber.
Program block
Explanation
CASSIG CASSIG sets the clear code when an unknown message is received in reply to the seizure.
Program block
Explanation
CASSIG CASSIG sets the clear code when the B-ONHOOK signal is intercepted in conversation state and yet charging has been defined for the the incoming circuit. 'B-ONHOOK signal intercepted' means this; The B-subscriber can continue a call after hanging up (B-ONHOOK) by picking up the receiver within the limits of the time supervision. The conversation state is maintained for the time allowed by the time supervision. Within this time the B-ONHOOK can be intercepted. CASSIG sets the clear code when the following line signals are received from LIRECE; CLEAR-REQUEST, SPECIALLY_LONG_SIGNAL_BEGUN, or SPECIAL_TRAFFIC_TYPE.
DN078927Issue 1-0
39
DX200 Clear Code List Clear codes
Id:0900d80580635beb
Possibility to change the default effectNot possible.
AlarmsNo alarms.
5.31 203H - B-CHANNEL UNACCEPTABLE
Text in MML printoutsB CHANNEL UNACCEPTABLE
DescriptionThe terminal equipment of an ISDN subscriber does not accept the B-channel offered by the exchange.
Detected by-
Default effect on the exchangeThe outgoing circuit is hunted again. The number of hunting attempts is indicated in the outgoing signalling record.
Possibility to change the default effectNot possible.
AlarmsNo alarms.
5.32 204H - ESTABLISHED B-CHANNEL
Text in MML printoutsESTABLISHED B CHANNEL
DescriptionThe call set-up is attempted on a channel which is occupied by another call (other calls).
Detected by
Default effect on the exchangeThe call is cleared in terminal and transit exchanges. The originating exchange connects a special information tone to the subscriber.
Program block
Explanation
- 2B+D terminal equipment.
40 DN078927Issue 1-0
DX200 Clear Code List
Id:0900d80580635beb
Clear codes
Possibility to change the default effectNot possible.
AlarmsNo alarms.
5.33 206H - CALL REJECTED
Text in MML printoutsCALL REJECTED
DescriptionThe call is rejected by an ISDN subscriber's terminal equipment. Seen from the exchange, the call is successful, since the terminal equipment is neither busy nor incom-patible.
Detected by
Default effect on the exchangeThe call is cleared in transit exchanges. The originating exchange connects a conges-tion tone to the subscriber.
Possibility to change the default effectNot possible.
AlarmsNo alarms.
5.34 207H - SUBSCRIBER CONGESTION
Text in MML printoutsSUBSCRIBER CONGESTION
DescriptionThe terminal equipment of an ISDN subscriber has informed the exchange that the resources needed for call reception are not available.
Detected by-
Program block
Explanation
- ISDN terminal equipment.
DN078927Issue 1-0
41
DX200 Clear Code List Clear codes
Id:0900d80580635beb
Default effect on the exchangeThe call is cleared in terminal and transit exchanges. The originating exchange connects a special information tone to the subscriber.
Possibility to change the default effectNot possible.
AlarmsNo alarms.
5.35 20BH - CLEAR IN DETAILED CHARGING
Text in MML printoutsCLEAR IN TOLL TICKETING
DescriptionDetailed charging has been defined for the outgoing circuit group, and the signalling of the incoming circuit group does not allow for an interrogation of the calling subscriber's number.
Detected by-
Default effect on the exchangeThe call is cleared in terminal and transit exchanges. The originating exchange connects a special information tone to the subscriber.
Possibility to change the default effectNot possible.
AlarmsNo alarms.
5.36 20EH - CALLING SUBSCRIBER LINE VACANT OR OUT OF SERVICE
Text in MML printoutsA-LINE VACANT
DescriptionThe calling subscriber (A-subscriber) has not been created in the exchange data, i.e. the files indicate that the position number is vacant. A-subscriber's line out of service. The data is stored in the subscriber data in the central memory.
42 DN078927Issue 1-0
DX200 Clear Code List
Id:0900d80580635beb
Clear codes
Detected by
Default effect on the exchangeThe call is cleared in terminal and transit exchanges. The originating exchange connects a special information tone to the subscriber.
Possibility to change the default effectNot possible.
AlarmsNo alarms.
5.37 20FH - CHANGE OF OUTGOING CIRCUIT
Text in MML printoutsCHANGE OF OUTG CIRCUIT
DescriptionDue to external congestion in the network, the call control has seized a new outgoing circuit for the call. The clear code is set on the old circuit to be released. This situation is possible only when the release of the old circuit lasts longer than the seizure of the new one.
Detected by-
Default effect on the exchangeThe call is cleared in terminal and transit exchanges. The originating exchange connects a special information tone to the subscriber.
Possibility to change the default effectNot possible.
AlarmsNo alarms.
5.38 210H - NULL NUP
Text in MML printoutsNULL NUP
Program block
Explanation
IC6PRB IC6PRB or INREGI (ARF) sets the clear code when there is no number created for the A-subscriber in the exchange.
DN078927Issue 1-0
43
DX200 Clear Code List Clear codes
Id:0900d80580635beb
DescriptionThe reason for release is either unknown or has previously been received (used in NUP signalling) or CCBS recall has not succeeded ( The called A subscriber does not answer ).
Detected by
Default effect on the exchangeThe call is cleared in transit exchanges. The originating exchange connects a special information tone to the subscriber.
Possibility to change the default effectNot possible.
AlarmsNo alarms.
5.39 211H - NETWORK, REJECTED DIVERTED CALLS
Text in MML printoutsREJECTED DIVERTED CALLS
DescriptionDiverted calls are not accepted by the B subscriber.
Detected by
Default effect on the exchange–
Possibility to change the default effectNot possible.
AlarmsNo alarms.
Program block
Explanation
CPLPRB CPLPRB sets the clear code when the called A subscriber does not answer during CCBS recall.
SI4PRB SI4PRB sets the clear code when the reason for release has been received previously. CPLPRB sets the clear code when the called A sub-scriber does not answer during CCBS recall.
Program block
Explanation
SI4PRB SI4PRB sets this clear code when a RELEASE message with the cause code Rejected Diverted Calls is received from a NUP circuit.
44 DN078927Issue 1-0
DX200 Clear Code List
Id:0900d80580635beb
Clear codes
5.40 213H - NETWORK, USER NOT IN CUG
Text in MML printoutsN USER NOT IN CUG
DescriptionThe subscriber is not in the closed user group. The release cause is received from the network.
Detected by
Default effect on the exchange–
Possibility to change the default effectNot possible.
AlarmsNo alarms.
5.41 215H - CALL DROP BACK
Text in MML printoutsDROPPED CALL
DescriptionCause code #23 (ISUP signalling) has been received from the network. If the feature Call Drop Back is supported, the call is rerouted. Otherwise the call is cleared in a way depending on the incoming signalling.
Detected by
Default effect on the exchangeThe call is cleared in terminal and transit exchanges. The originating exchange carries out a digit re-analysis in the interception tree 32H.
Program block
Explanation
SI7PRB SI7PRB sets this clear code when it has received the corresponding release cause from the network.
Program block
Explanation
SI7PRB SI7PRB sets this clear code when it receives cause code #23 from the network.
DN078927Issue 1-0
45
DX200 Clear Code List Clear codes
Id:0900d80580635beb
Possibility to change the default effectUsing facility routing (command group RE, parameter CCF) terminal and transit exchanges can connect an audible tone to the subscriber or carry out a digit re-analysis in tree 32H. Using facility routing, the originating exchange can connect an audible tone to the calling subscriber. If the feature Call Drop Back is in use in the exchange, the call can be re-analysed in the desired tree set by the EOS Analysis Management -MML (command group RX). The redirecting number received in the release message from the network is used as the routing number.
AlarmsNo alarms.
5.42 216H - MISDIALLED TRUNK PREFIX
Text in MML printoutsMISDIALLED TRUNK PREFIX
DescriptionErroneous inclusion of a trunk prefix in the called party number.
Detected by
Default effect on the exchangeThe call is cleared in terminal and transit exhanges. The originating exchange connects a congestion tone to a subscriber.
Possibility to change the default effectNot possible.
AlarmsNo alarms.
5.43 217H - TEMPORARY OUT OF ORDER
Text in MML printoutsTEMPORARY OUT OF ORDER
Program block
Explanation
SI3PRB SI3PRB and SI5PRB set this clear code when MPR message is received from a network. SI7PRB sets the code when cause #5 is received from a network.
SI5PRB SI3PRB and SI5PRB set this clear code when MPR message is received from a network. SI7PRB sets the code when cause #5 is received from a network.
46 DN078927Issue 1-0
DX200 Clear Code List
Id:0900d80580635beb
Clear codes
DescriptionShows that the required subscriber line is not in service as a result of administrative action or at the request of the subscriber.
Detected by
Default effect on the exchangeThe call is cleared in terminal and transit exchanges. The originating exchange connects busy tone to the subscriber.
Possibility to change the default effectNot possible.
AlarmsNo alarms.
5.44 218H - OUT OF CATCHMENT AREA
Text in MML printoutsOUT OF CATCHMENT AREA
DescriptionShows that access to the destination address as given in the IAM/IFAM is dependent on the caller's catchment area (normally based on CLI). For this call the caller was in a dis-allowed catchment area.
Detected by
Default effect on the exchangeThe call is cleared in terminal and transit exchanges. The originating exchange connects a special information tone to the subscriber.
Possibility to change the default effectNot possible.
AlarmsNo alarms.
Program block
Explanation
SI4PRB –
Program block
Explanation
SI4PRB –
DN078927Issue 1-0
47
DX200 Clear Code List Clear codes
Id:0900d80580635beb
5.45 219H - TRANSLATION OUT-OF-SERVICE
Text in MML printoutsTRANSLATION OUT OF SERVICE
DescriptionShows that call rejection has occurred as there is temporarily no active translation for the called address.
Detected by
Default effect on the exchangeThe call is cleared in terminal and transit exchanges. The originating exchange connects a special information tone to the subscriber.
Possibility to change the default effectNot possible.
AlarmsNo alarms.
5.46 220H - ANONYMOUS CALLS REJECTION
Text in MML printoutsANONYMOUS CALLS REJECTION
DescriptionThe called subscriber does not accept calls from subscribers who withhold their numbers from showing to the called party.
Detected by
Default effect on the exchangeThe call is cleared in terminal and transit exchanges. The originating exchange connects busy tone to the subscriber.
Possibility to change the default effectNot possible.
Program block
Explanation
SI4PRB –
Program block
Explanation
SI4PRB –
48 DN078927Issue 1-0
DX200 Clear Code List
Id:0900d80580635beb
Clear codes
AlarmsNo alarms.
5.47 252H - UNTERMINATED CALL TO A PORTED NUMBER
Text in MML printoutsUNTERMINATED PORTED CALL
DescriptionThis cause code is used to release the call with ISUP REL cause 112, Misrouted call to a ported number.
Detected by
Default effect on the exchangeSI7PRB (SSI) clears the call with ISUP REL cause code 112. Originating exchange connects special tone. Terminating exchange clears backwards with cause 112
Possibility to change the default effectOriginating exchange can use facility routing or interception in tree 2AH.
AlarmsNo alarms.
5.48 300H - CALLING SUBSCRIBER BARRED DUE TO RESTRICTION IN THE OUTGOING DIRECTION
Text in MML printoutsOUTGOING CALLS BARRED
DescriptionA call from the calling subscriber (A-subscriber) is routed to a direction to which it has no access due to an outgoing call restriction category. The subscriber has barred the outgoing call with a supplementary service restricting outgoing calls. This barring infor-mation is stored in the central memory or in the VLR. This clear code is also used if the subscribers' calls in the PABX are barred outside the local network.
Program block
Explanation
OC2PRB OC2PRB sets this clear code when HLR responded to SRI with clear code 0x307 B_number unused and the cc setup message indicates that the call is routed with Location Routing Number. New cause code 112 (Ported Number not found) is Sweden specific value. If terminating network receives a call with the indication of ported number but the terminating network does not recognise the called Directory Number as belonging to the network, or as unallocated, the the terminating network shall release the call with the cause 112.
DN078927Issue 1-0
49
DX200 Clear Code List Clear codes
Id:0900d80580635beb
Detected by
Default effect on the exchangeThe originating exchange connects a congestion tone to the subscriber. The clear code can only be set in the originating exchange.
Possibility to change the default effectUsing facility routing (command group RE, parameter CAB), the call can be directed for reanalysis in tree 35H both in terminal and transit exchanges, however, not in an exchange that has the A-validation feature. In A-validation cases a tone is connected to the calling subscriber.
AlarmsNo alarms.
5.49 301H - CALLING SUBSCRIBER'S OUTGOING CALL RESTRICTED BY OPERATOR
Text in MML printoutsOPER RESTR IN OUT DIRECT
DescriptionA call from the calling subscriber (A-subscriber) goes to a route to which it has no access due to outgoing call restriction activated by the operator. E.g. the barring of outgoing Centrex-calls.
Detected by
Default effect on the exchangeThe call is cleared in terminal and transit exchanges. The originating exchange connects a special information tone to the subscriber.
Possibility to change the default effectNot possible.
AlarmsNo alarms.
Program block
Explanation
IC6PRB IC6PRB or INREGI sets the clear code when the call set-up is barred by subscriber-specific restriction of outgoing calls.
Program block
Explanation
IC6PRB IC6PRB sets the clear code if the call set-up is barred by the outgoing call restriction of the Centrex-subscriber.
50 DN078927Issue 1-0
DX200 Clear Code List
Id:0900d80580635beb
Clear codes
5.50 304H - CALLED SUBSCRIBER LINE OUT OF SERVICE
Text in MML printoutsB-LINE OUT OF SERVICE
DescriptionThe line of the called subscriber (B subscriber) is out of service. The information is in the subscriber data of the central memory.
Detected by
Default effect on the exchangeThe call is cleared in terminal and transit exchanges. The originating exchange carrºies out a digit re-analysis in interception tree
Possibility to change the default effectUsing facility routing, an audible tone can be connected to the subscriber. Interception tree 35H (command group RE, parameter CAB). Interception tree 30H (command group RE, parameter CBO).
AlarmsNo alarms.
5.51 305H - CALLED SUBSCRIBER LINE FAULTY
Text in MML printoutsB-LINE FAULTY
DescriptionThe line of the called subscriber (B-subscriber) is faulty. The data is stored in the sub-scriber data of the central memory.
Detected by
Program block
Explanation
OC6PRB OC6PRB or OUREGI sets the clear code, when "connection closed" has been set in the called-subscriber data. INREGI sets the clear code, when "exchange closed" has been set in the supplementary-direction data.
Program block
Explanation
OC6PRB OUREGI or OC6PRB sets the clear code, when "line faulty" has been set in the called-subscriber data.
DN078927Issue 1-0
51
DX200 Clear Code List Clear codes
Id:0900d80580635beb
Default effect on the exchangeThe call is cleared in terminal and transit exchanges. The originating exchange carries out a digit re-analysis in tree 2FH.
Possibility to change the default effectUsing facility routing (command group RE, parameter CFB), transit and terminal exchanges can carry out a digit re-analysis in tree 2FH, or connect an audible tone to the subscriber. Using facility routing, the originating exchange can connect an audible tone to the subscriber.
AlarmsNo alarms.
5.52 306H - ACCESS TO B-SUBSCRIBER LINE RESTRICTED
Text in MML printoutsB-CALLS RESTRICTED
DescriptionAccess to the B-subscriber line (called line) is restricted, and the category of the calling subscriber does not allow the bypassing of the restriction. The called subscriber has pre-vented the incoming call with a supplementary service. The information is set in the sub-scriber data of the central memory or in the HLR. This clear code is also set when the calling and called subscribers are incompatible and the operation presupposes a call release.
Detected by
Default effect on the exchangeThe call is cleared in terminal and transit exchanges. The originating exchange carries out a digit re-analysis in tree 35H.
Possibility to change the default effectUsing facility routing (command group RE, parameter CAB), the originating exchange and connect an audible tone to the subscriber, and terminal and transit exchanges can carry out a digit re-analysis in tree 35H, or connect an audible tone to the subscriber.
AlarmsNo alarms.
5.53 307H - B-NUMBER UNUSED
Program block
Explanation
OC6PRB OC6PRB, OUREGI or OC1PRB sets the clear code when the call set-up is not possible due to incoming call barring (ICB) of the called subscriber, or restricted access to the B-subscriber (RAB).
52 DN078927Issue 1-0
DX200 Clear Code List
Id:0900d80580635beb
Clear codes
Text in MML printoutsB-NUMBER UNUSED
DescriptionThe central memory's answer to the digit analysis is B-NUMBER UNUSED.
Detected by
Default effect on the exchangeThe call is cleared in terminal and transit exchanges. The originating exchange carries out a digit re-analysis in tree 2AH.
Possibility to change the default effectUsing facility routing (command group RE, parameter CUN), terminal and transit exchanges can connect an audible tone to the subscriber or carry out a digit re-analysis in tree 2AH. Using facility routing, the originating exchange can connect an audible tone to the subscriber.
AlarmsNo alarms.
5.54 308H - B-NUMBER CHANGED
Text in MML printoutsB-NUMBER CHANGED
DescriptionThe central memory's answer to the digit analysis by the register is NUMBER CHANGED.
Detected by
Default effect on the exchangeThe call is cleared in terminal and transit exchanges. The originating exchange carries out a digit re-analysis in tree 29H.
Program block
Explanation
ICXPRB ICxPRB or INREGI sets the clear code when information is received from the digit analysis that the analysed number is unused.
Program block
Explanation
ICXPRB ICxPRB or INREGI sets the clear code when information is received from the digit analysis that the number of the called subscriber has changed.
DN078927Issue 1-0
53
DX200 Clear Code List Clear codes
Id:0900d80580635beb
Possibility to change the default effectUsing facility routing (command group RE, parameter CSN), terminal and transit exchanges can connect an audible tone to the subscriber or carry out a digit re-analysis in tree 29H. Using facility routing, the originating exchange can connect an audible tone to the calling subscriber.
AlarmsNo alarms.
5.55 309H - TIME-OUT WHEN WAITING FOR OPERATOR'S INTERVENTION
Text in MML printoutsWAIT FOR INTERV TIME OUT
DescriptionAn intervention signal has not arrived before time-out.
Detected by
Default effect on the exchangeThe call is cleared in terminal and transit exchanges. The originating exchange connects a congestion tone to the subscriber.
Possibility to change the default effectNot possible.
AlarmsNo alarms.
5.56 30AH - CLEAR/CALLING SUBSCRIBER HAS MADE ONHOOK DURING SET-UP PHASE
Text in MML printoutsA ONHOOK DURING SET UP
DescriptionThe connection has been cleared in the set-up phase either due to a calling subscriber onhook or because a signal or a message equivalent to clearing has been received from the incoming circuit.
Program block
Explanation
CASSIG CASSIG sets the clear code if the operator calls an engaged line and an intervention tone is not received within the time supervision.
54 DN078927Issue 1-0
DX200 Clear Code List
Id:0900d80580635beb
Clear codes
Detected by
Default effect on the exchangeThe call is cleared. An audible tone will not be connected because of subscriber onhook.
Possibility to change the default effectNot possible.
AlarmsNo alarms.
5.57 30BH - CLEAR/CALLING SUBSCRIBER HAS MADE ONHOOK WHEN WAITING FOR ANSWER
Text in MML printoutsA ONHOOK DUR_WAIT ANSWER
DescriptionOnhook by the calling subscriber (A-subscriber) has taken place before the called sub-scriber (B-subscriber) has answered, or a signal or message equivalent to clearing has been received from the incoming circuit.
Detected by
Default effect on the exchangeThe call is cleared. An audible tone will not be connected because of subscriber onhook.
Possibility to change the default effectNot possible.
AlarmsNo alarms.
5.58 30CH - REANSWER TIME OUT
Program block
Explanation
SIXPRB SIxPRB or CASSIG sets the clear code when the calling subscriber makes onhook before the end-of-selection information is received.
Program block
Explanation
SIXPRB CASSIG, SIxPRB or ICxPRB sets the clear code when, after the end-of-selection information has been received, the calling subscriber makes onhook before the called subscriber has answered.
DN078927Issue 1-0
55
DX200 Clear Code List Clear codes
Id:0900d80580635beb
Text in MML printoutsREANSWER TIME OUT
DescriptionThe calling/called subscriber has not answered within the time supervision.
Detected by
Default effect on the exchangeThe call is cleared in terminal and transit exchanges. The originating exchange connects a busy tone to the subscriber who has not made onhook.
Possibility to change the default effectNot possible.
AlarmsNo alarms.
5.59 30DH - B- OR C-NUMBER IS NOT REGISTERED
Text in MML printoutsB-NUMB IS NOT REGISTERED
DescriptionThe number related to the service is not found in the central memory. Such services are Abbreviated Dialling, Fixed Destination Call and Call Diversion.
Detected by
Default effect on the exchangeThe call is cleared in terminal and transit exchanges. The terminating exchange connects a congestion tone to the subscriber.
Possibility to change the default effectNot possible.
Program block
Explanation
ICXPRB CASSIG or ICxPRB sets the clear code if the subscriber has not rean-swered within the time limit.
Program block
Explanation
IC6PRB IC6PRB, INREGI, OUREGI or CFOPRB sets the clear code when the B-subscriber number connected with the subscriber facility is not obtained from the subscriber database.
56 DN078927Issue 1-0
DX200 Clear Code List
Id:0900d80580635beb
Clear codes
AlarmsNo alarms.
5.60 30EH - CALLED SUBSCRIBER LINE BLOCKED
Text in MML printoutsB-LINE BLOCKED
DescriptionThe called subscriber (B-subscriber) is in line blocking state.
Detected by
Default effect on the exchangeThe call is cleared in terminal and transit exchanges. In the originating exchange, a digit reanalysis is performed in the announcement tree. The originating exchange connects a congestion tone to the subscriber or performs reanalysis in the interception tree 35H.
Possibility to change the default effectBy using facility routing, the call can be directed for a reanalysis in an interception tree in both terminal and transit exchanges. In the originating exchange, an audible tone can be connected to the subscriber using facility routing, interception tree 2FH (command group RE, parameter CFB). Interception tree 35H (command group RE, parameter CAB).
AlarmsNo alarms.
5.61 30FH - CHANGE IN NUMBERING PLAN
Text in MML printoutsCHANGE IN NUMBER PLANNING
DescriptionThe digit analysis indicates that the numbering plan for the outgoing direction has changed.
Program block
Explanation
SI6PRB The SI6PRB sets the clear code when the AICPRB informs that the sub-scriber is in line blocking state. The OUREGI sets the clear code when the ARF subscriber line is in line blocking state.
DN078927Issue 1-0
57
DX200 Clear Code List Clear codes
Id:0900d80580635beb
Detected by
Default effect on the exchangeThe call is cleared in terminal and transit exchanges. The originating exchange performs a reanalysis of the dialling using the tree 2BH (command group RE, parameter CNP).
Possibility to change the default effectUsing facility routing, the terminal and transit exchanges can perform a reanalysis of the dialling in the tree 2BH or connect an audible information tone to the subscriber. The originating exchange can connect an audible information tone to the subscriber using facility routing.
AlarmsNo alarms.
5.62 310H - CLOSED USER GROUP RESCTRICTION
Text in MML printoutsCUG REJECT
DescriptionThe location register (LR) indicates that the call did not pass the CUG check or that the CUG barring conditions were transgressed. For example, in ISDN calls this clear code may indicate that access to a specified closed user group is barred.
Detected by-
Default effect on the exchangeThe selected number is re-analysed in tree 35H (command group RE, parameter CAB).
Possibility to change the default effectUsing facility routing, an audible tone can be connected to the calling subscriber.
AlarmsNo alarms.
5.63 311H - BEARER SERVICE NOT PROVIDED
Text in MML printoutsBEARER SERV NOT PROV
Program block
Explanation
ICXPRB IC1PRB, IC3PRB, IC6PRB, INREGI
58 DN078927Issue 1-0
DX200 Clear Code List
Id:0900d80580635beb
Clear codes
DescriptionThe subscriber has not subscribed to the bearer service defined for the call, or the GSM BCIE is faulty.
Detected by
Default effect on the exchangeThe originating exchange carries out a digit re-analysis in tree 32H (command group RE, parameter CCF). The call is cleared in terminal and transit exchanges.
Possibility to change the default effectUsing facility routing, the originating exchange can connect an audible tone to the sub-scriber. Using facility routing (command group RE, parameter CST), terminal and transit exchanges can carry out a digit re-analysis in tree 34H.
AlarmsNo alarms.
5.64 312H - TELESERVICE NOT PROVIDED
Text in MML printoutsTELE SERV NOT PROV
DescriptionThe subscriber has not subscribed to the teleservice defined for the call, or the GSM BCIE is faulty.
Detected by-
Default effect on the exchangeThe call is cleared in terminal and transit exchanges. The originating exchange connects a special information tone to the subscriber.
Possibility to change the default effectNot possible.
AlarmsNo alarms.
5.65 315H - CALLED SUBSCRIBER HAS CALL DIVERSION BARRING
Program block
Explanation
SI5PRB SI5PRB.
DN078927Issue 1-0
59
DX200 Clear Code List Clear codes
Id:0900d80580635beb
Text in MML printoutsB HAS CALL DIVERS BARRING
Description1. Call diversion barring is set in the subscriber data of the called subscriber. 2. The number of diversions per call exceeds the set limit.
Detected by
Default effect on the exchangeThe call is cleared in terminal and transit exchanges. The originating exchange carries out a digit re-analysis in tree 35H. The originating exchange connects a congestion tone to the subscriber or performs reanalysis in the interception tree 35H.
Possibility to change the default effectUsing facility routing (command group RE, parameter CBB), the originating exchange can connect an audible tone to the subscriber. The terminal and transit exchanges can carry out a digit re-analysis in tree 35H, or connect an audible tone to the subscriber.
AlarmsNo alarms.
5.66 317H - TIME-OUT IN INTELLIGENT NETWORK BASED SUBSCRIBER SERVICE
Text in MML printoutsIN SERVICE TIME EXCEEDED
DescriptionThe overall time limit of an intelligent network (IN) based subscriber service has been exceeded.
Detected by
Default effect on the exchangeThe call is cleared in terminal and transit exchanges. The originating exchange connects a special information tone to the subscriber.
Program block
Explanation
OC6PRB OC6PRB or OUREGI sets the clear code when the call is diverted, but the subscriber data indicates that call diversion to the subscriber is not allowed. IC3PRB sets the clear code when call diversion involves a manual answering service.
Program block
Explanation
IDXSCP –
60 DN078927Issue 1-0
DX200 Clear Code List
Id:0900d80580635beb
Clear codes
Possibility to change the default effectNot possible.
AlarmsNo alarms.
5.67 31AH - INCOMING CALLS BARRED WITHIN THE CUG
Text in MML printoutsCUG REJ IC CALL BARRED
DescriptionThe call is rejected because of an incoming call barring within the closed user group (CUG).
Detected by
Default effect on the exchangeThe call is cleared in terminal and transit exchanges. The originating exchange connects a congestion tone to the subscriber.
Possibility to change the default effectNot possible.
AlarmsNo alarms.
5.68 31CH - SUBSCRIBER NOT A MEMBER OF THE CUG
Text in MML printoutsCUG REJ NOT MEMBER
DescriptionThe call is rejected because the subscriber is not a member of the closed user group (CUG).
Program block
Explanation
ICXPRB In a mobile terminating call, the IC1PRB, the IC2PRB or the IC3PRB sets this clear code if the HLR returns information that incoming calls are barred within the CUG.
DN078927Issue 1-0
61
DX200 Clear Code List Clear codes
Id:0900d80580635beb
Detected by
Default effect on the exchange–
Possibility to change the default effectNot possible.
AlarmsNo alarms.
5.69 31DH - OUTGOING CALLS BARRED WITHIN THE CUG
Text in MML printoutsCUG REJ OG CALL BARRED
DescriptionThe call is rejected because of an outgoing call barring within the closed user group (CUG).
Detected by
Default effect on the exchange–
Possibility to change the default effectNot possible.
AlarmsNo alarms.
Program block
Explanation
ICXPRB In a mobile terminating call, the IC1PRB, the IC2PRB or the IC3PRB sets this clear code if the HLR or the VLR returns information that the sub-scriber is not a member of the CUG. In a PBX terminating call, the OC1PRB sets this clear code if the called PBX is not a member of the CUG. The called party CUG check fails because the called party does not belong to the same CUG with the calling party, and the calling party does not use outgoing access or the called party does not have incoming access.
Program block
Explanation
ICXPRB The IC2PRB sets this clear code if the VLR returns information that outgoing calls are barred within the CUG.
62 DN078927Issue 1-0
DX200 Clear Code List
Id:0900d80580635beb
Clear codes
5.70 321H - NO CUG SELECTED
Text in MML printoutsCUG REJ NO CUG SELECTED
DescriptionThe call is rejected because no closed user group (CUG) has been selected.
Detected by
Default effect on the exchange–
Possibility to change the default effectNot possible.
AlarmsNo alarms.
5.71 322H - UNKNOWN CUG INDEX
Text in MML printoutsCUG REJ UNKNOWN CUG IND
DescriptionThe call is rejected because the index of the closed user group (CUG) is unknown.
Program block
Explanation
ICXPRB In a mobile originating call, the IC2PRB sets this clear code if the VLR returns information that there is no CUG selected. In mobile originating calls this information is used in three different situations; first, if the calling subscriber does not provide the CUG index in the call setup although there is no outgoing access, and a preferred CUG is not defined; second, if the calling subscriber tries to suppress the preferred CUG and there is no outgoing access; and third, if the calling subscriber has an outgoing access but no preferred CUG, but tries to suppress the outgoing access and does not provide a CUG index in call setup. In a PBX originating call, the IC1PRB sets this clear code when the preferential CUG has not been defined in the PBX.
DN078927Issue 1-0
63
DX200 Clear Code List Clear codes
Id:0900d80580635beb
Detected by
Default effect on the exchange–
Possibility to change the default effectNot possible.
AlarmsNo alarms.
5.72 400H - ATTENUATOR CONGESTION
Text in MML printoutsATTENUATOR CONGESTION
DescriptionAttenuator seizure ended in congestion.
Detected by-
Default effect on the exchangeThe call is cleared in terminal and transit exchanges. The originating exchange connects a special information tone to the subscriber.
Possibility to change the default effectNot possible.
AlarmsNo alarms.
5.73 401H - INTERWORKING UNIT CONGESTION
Text in MML printoutsINTERW UNIT CONGESTION
DescriptionThere are no free circuits available in the interworking unit.
Program block
Explanation
ICXPRB The IC2PRB sets this clear code if the VLR returns information that the closed user group index is unknown. The call is rejected because a calling subscriber makes the call with a CUG index which is unknown for the sub-scriber.
64 DN078927Issue 1-0
DX200 Clear Code List
Id:0900d80580635beb
Clear codes
Detected by
Default effect on the exchangeThe call is cleared in terminal and transit exchanges. The originating exchange connects a special information tone to the subscriber.
Possibility to change the default effectNot possible.
AlarmsNo alarms.
5.74 402H - REGISTER TOTAL TIME EXCEEDED
Text in MML printoutsREGISTER TOTAL TIME EXC
DescriptionThe total time limit for the call set-up has been exceeded. For example, the time limit for the MFC device has been exceeded in the MFST plug-in unit.
Detected by
Default effect on the exchangeThe call is cleared in transit exchanges. The originating exchange connects a conges-tion tone to the subscriber.
Possibility to change the default effectNot possible.
AlarmsNo alarms.
Program block
Explanation
ASEPRB –
SREPRB –
Program block
Explanation
IC6PRB IC6PRB or INREGI sets the clear code when the total time limit for the call setup(ie the time from the call beginning to the end-of-selection informa-tion) is exceeded.
INREGI IC6PRB or INREGI sets the clear code when the total time limit for the call set-up (ie the time from the call beginning to the end-of-selection informa-tion) is exceeded.
DN078927Issue 1-0
65
DX200 Clear Code List Clear codes
Id:0900d80580635beb
5.75 403H - MFCU DEVICE CONGESTION
Text in MML printoutsMFCU CONGESTION
DescriptionNo free MFCU devices available.
Detected by
Default effect on the exchangeThe call is cleared in terminal and transit exchanges. The originating exchange connects a special information tone to the subscriber.
Possibility to change the default effectNot possible.
AlarmsNo alarms.
5.76 404H - PBRU DEVICE CONGESTION
Text in MML printoutsPBRU CONGESTION
DescriptionNo free PBRU devices available.
Detected by
Default effect on the exchangeThe call is cleared in terminal and transit exchanges. The originating exchange connects a special information tone to the subscriber.
Possibility to change the default effectNot possible.
Program block
Explanation
INREGI INREGI or OUREGI sets the clear code when ACSERV reports that the reservation of the MFCU device failed.
Program block
Explanation
SI6PRB SI6PRB sets the clear code when ACSERV reports that the reservation of the PBRU device failed.
66 DN078927Issue 1-0
DX200 Clear Code List
Id:0900d80580635beb
Clear codes
AlarmsNo alarms.
5.77 405H - ERRONEOUS SERVICE REQUEST FROM CO-PROCESS
Text in MML printoutsERR REQUE FROM COPROCESS
DescriptionA program block has received a service request containing erroneous or missing param-eters, or the request was received in a wrong phase of the call.
Detected by
Default effect on the exchangeThe call is cleared in terminal and transit exchanges. The originating exchange connects a special information tone to the subscriber.
Possibility to change the default effectNot possible.
AlarmsNo alarms.
5.78 406H - CONNECTION FAILED IN GSW/SWI
Text in MML printoutsCONNECT FAILED IN GSW/SWI
DescriptionThe connection to the GSW switching network of a DX 220 exchange or to the SWI switching network of a DX 210 exchange needed for call set-up has failed. This clear code is used with connections which are not performed to the SSW switching network of a DX 220 exchange. The program block which requested for the connection has not been able to contact the marker, or the SWICOP program block, or the RMAPRB program block, has not responded within the time limit, or the response is that the con-nection has failed.
Program block
Explanation
ASEPRB ASEPRB IC3PRB IDOPRB RMAPRB
IC3PRB –
IDOPRB –
RMAPRB –
DN078927Issue 1-0
67
DX200 Clear Code List Clear codes
Id:0900d80580635beb
Detected by
Default effect on the exchangeThe call is cleared in terminal and transit exchanges. The originating exchange connects a special information tone to the subscriber.
Possibility to change the default effectNot possible.
AlarmsNo alarms.
5.79 407H - ERRONEOUS ANSWER FROM PARTNER PROGRAM BLOCK
Text in MML printoutsERR ANSWER FROM CO-PROC
DescriptionAn unknown or erroneous message has been received from the program block acting as the partner of a program block belonging to one of the following system blocks: call control, signalling services, or switching services.
Detected by
Program block
Explanation
INREGI INREGI or OUREGI sets the clear code when SWICOP sends the 4130 or 4129 message in response, or when SCRPRB gives no response at all.
Program block
Explanation
ASEPRB The following programs set the clear code when the response to a service request is that the service is not available. ASEPRB, CFOPRB, CPLPRB, GCAPRB, IDOPRB, LHSPRB, OC1PRB, OC6PRB, INREGI, OUREGI, SI5PRB, SI6PRB, SI7PRB, SREPRB.
CFOPRB –
CPLPRB –
GCAPRB –
IDOPRB –
INREGI –
LHSPRB –
OC1PRB –
OC6PRB –
OUREGI –
68 DN078927Issue 1-0
DX200 Clear Code List
Id:0900d80580635beb
Clear codes
Default effect on the exchangeThe call is cleared in terminal and transit exchanges. The originating exchange connects a congestion tone to the subscriber.
Possibility to change the default effectNot possible.
AlarmsNo alarms.
5.80 408H - LENGTH OF CALLED SUBSCRIBER NUMBER EXCEEDED
Text in MML printoutsB-NUMBER LENGTH EXCEEDED
DescriptionThe length of the called subscriber's (B-subscriber) number has been exceeded, and the call control cannot perform a digit analysis.
Detected by
Default effect on the exchangeThe call is cleared in terminal and transit exchanges. The originating exchange connects a special information tone to the subscriber.
Possibility to change the default effectNot possible.
AlarmsNo alarms.
SI5PRB –
SI6PRB –
SI7PRB –
SREPRB –
Program block
Explanation
Program block
Explanation
ICXPRB ICxPRB or INREGI sets the clear code when saving the selected number fails due to overflow.
INREGI –
DN078927Issue 1-0
69
DX200 Clear Code List Clear codes
Id:0900d80580635beb
5.81 409H - CONNECTION FAILED IN SSW/SWI
Text in MML printoutsCONNECT FAILED IN SSW/SWI
DescriptionThere has been a failure in making the connection to the SSW switching network of a DX 220 exchange. This clear code is used for connections performed to the SSW switching network of a DX 220 exchange. The program block which requested for the connection receives an answer from the marker on the connection failure.
Detected by
Default effect on the exchangeThe call is cleared in terminal and transit exchanges. The originating exchange connects a special information tone to the subscriber.
Possibility to change the default effectNot possible.
AlarmsNo alarms.
5.82 40AH - CIRCUIT CONGESTION DUE TO TRAFFIC TYPE
Text in MML printoutsTRAFFIC TYPE CONGESTION
DescriptionTraffic type congestion which is caused by selective circuit congestion or automatic con-gestion control.
Program block
Explanation
INREGI INREGI or OUREGI sets the clear code when the MFCU cannot be reserved within the time supervision.
OUREGI –
70 DN078927Issue 1-0
DX200 Clear Code List
Id:0900d80580635beb
Clear codes
Detected by
Default effect on the exchange–
Possibility to change the default effectNot possible.
AlarmsNo alarms.
5.83 40BH - HOP COUNTER EXHAUST
Text in MML printoutsHOP COUNTER EXHAUST
DescriptionError in routing. Hop counter exhausts in the exchange. The hop counter has an initial (maximal) value, which is decreased in every intermediate exchange. When it becomes zero, the call is cleared and an alarm is given. The hop counter helps to prevent looping between networks in the multicarrier environment.
Detected by
Default effect on the exchangeThe call is released.
Possibility to change the default effectNot possible.
Program block
Explanation
RMAPRB RMAPRB sets the clear code when SWICOP returns the error code indi-cating that traffic type congestion has occurred in message congestion_on_route_s (4132). This occurs when selective circuit reser-vation or automatic congestion control rejection percentages cause the outgoing circuit reservation to fail. In both features the rejection percent-ages and continuation instructions for different traffic types (direct routed calls and alternatively directed calls) are defined. In selective circuit reser-vation the rejection percentages are applied after the user-defined thresh-old values have been reached. In automatic congestion control the rejection percentages are applied when the congestion level information has been received from the signalling point of the exchange to which the call is being routed.
Program block
Explanation
SI7PRB SI7PRB releases the call and sets #25 cause code.
DN078927Issue 1-0
71
DX200 Clear Code List Clear codes
Id:0900d80580635beb
Alarms1206
5.84 506H - LINES OF LINE HUNTING GROUPS BARRED
Text in MML printoutsLINES OF LINE HUNT GROUPS
DescriptionAll lines of the line hunting group acting as the B-subscriber have been barred from hunting. This information is included in the data of all lines in the hunting group.
Detected by-
Default effect on the exchangeThe call is cleared in terminal and transit exchanges. The originating exchange carries out a digit re-analysis in tree 35H.
Possibility to change the default effectUsing facility routing (command group RE, parameter CAB), the transit and terminal exchanges can connect an audible tone to the subscriber or carry out a digit re-analysis in tree 35H. Using facility routing, the originating exchange can connect an audible tone to the subscriber.
AlarmsNo alarms.
5.85 508H - CHARGING ERROR
Text in MML printoutsCHARGING ERROR
DescriptionThere has been an error in establishing charging during the call. The error may have been caused by a metering pulse of deviating length or by a wrong format in the charging message.
Detected by
Program block
Explanation
ICXPRB ICxPRB sets the clear code if the charging interface (CHRG_IF) reports that there has been a failure in performing the requested operation.
72 DN078927Issue 1-0
DX200 Clear Code List
Id:0900d80580635beb
Clear codes
Default effect on the exchangeThe call is cleared in terminal and transit exchanges. The originating exchange connects a special information tone to the subscriber.
Possibility to change the default effectNot possible.
AlarmsNo alarms.
5.86 509H - FILE ERROR
Text in MML printoutsFILE ERROR
DescriptionA program block belonging to the call control system block or to the signalling services system block has found that the contents of a file is faulty or that the reading of the file has failed.
Detected by
Default effect on the exchangeThe call is cleared in terminal and transit exchanges. The originating exchange connects a special information tone to the subscriber.
Possibility to change the default effectNot possible.
AlarmsNo alarms.
5.87 50BH - MODULE ROUTE OR SSW CONGESTION
Text in MML printoutsMODULE ROUTE OR SSW CONG
DescriptionCongestion in the subscriber stage.
Program block
Explanation
- Program blocks set the clear code if the opening of a file or access to a file fails.
DN078927Issue 1-0
73
DX200 Clear Code List Clear codes
Id:0900d80580635beb
Detected by
Default effect on the exchangeThe call is cleared in terminal and transit exchanges. The originating exchange carries out a digit re-analysis in tree 35H.
Possibility to change the default effectUsing facility routing (command group RE, parameter CAB), the originating exchange and connect an audible tone to the subscriber, and terminal and transit exchanges can carry out a digit re-analysis in tree 35H, or connect an audible tone to the subscriber.
AlarmsNo alarms.
5.88 50CH - MFC-ASS-CHANNEL CLOSING MISSED
Text in MML printoutsMFC-ASS-CHAN CLOSE MISSED
DescriptionThe closing command of the MFC-ASS channel has not been acknowledged within the time limit.
Detected by-
Default effect on the exchangeThe call is cleared in terminal and transit exchanges. The originating exchange connects a congestion tone to the subscriber.
Possibility to change the default effectNot possible.
AlarmsNo alarms.
5.89 50DH - FACILITY CONTROL FAILED
Text in MML printoutsFACILITY WRITING FAILED
Program block
Explanation
OUREGI OUREGI (ARF) sets the clear code when the seizure of an outgoing circuit fails.
74 DN078927Issue 1-0
DX200 Clear Code List
Id:0900d80580635beb
Clear codes
DescriptionThe activation or deactivation of a service has failed because there has been a failure in updating the service data in the central memory.
Detected by
Default effect on the exchangeThe call is cleared in terminal and transit exchanges. The originating exchange connects a special information tone to the subscriber.
Possibility to change the default effectNot possible.
AlarmsNo alarms.
5.90 50FH - UNSUITABLE MODULE CIRCUIT
Text in MML printoutsUNSUITABLE MODULE CIRCUIT
DescriptionThe hunted module circuit does not fit the subscriber module. This applies only to sub-scriber modules in a remote subscriber stage.
Detected by
Default effect on the exchangeThe call is cleared in terminal and transit exchanges. The originating exchange connects a special information tone to the subscriber.
Possibility to change the default effectNot possible.
AlarmsNo alarms.
Program block
Explanation
OUREGI OUREGI sets the clear code when the activation of a facility fails in the ARF signalling because CMSUBS cannot update the facility data in the subscriber database.
Program block
Explanation
SI6PRB SI6PRB sets the clear code when the module software reports that the seized time slot is in use already. This applies only to the subscriber modules SUB and SUB-C.
DN078927Issue 1-0
75
DX200 Clear Code List Clear codes
Id:0900d80580635beb
5.91 600H - FILE RECORD CONGESTION
Text in MML printoutsFILE RECORD CONGESTION
DescriptionA program block in the call control system block or in the signalling services system block has not been able to reserve the necessary dynamic record for a call. Typical cases are the reservations of the circuit records by SUBSIG or DACSIG in connection with a new call.
Detected by
Default effect on the exchangeThe call is cleared in terminal and transit exchanges. The originating exchange connects a special information tone to the subscriber.
Possibility to change the default effectNot possible.
AlarmsNo alarms.
5.92 601H - MODULE OR V5 CONGESTION
Text in MML printoutsMOD OR V5 LINK CONGESTION
DescriptionNo free module or V5 link(multiplexer) circuits are available. SI2PRB sets this clear code in the V5.1 interface if circuit reservation fails or if error situation is detected by V5 control protocol.
Detected by
Program block
Explanation
SI6PRB –
Program block
Explanation
SI2PRB –
SI6PRB –
76 DN078927Issue 1-0
DX200 Clear Code List
Id:0900d80580635beb
Clear codes
Default effect on the exchangeThe call is cleared in terminal and transit exchanges. The originating exchange connects a special information tone to the subscriber.
Possibility to change the default effectNot possible.
AlarmsNo alarms.
5.93 602H - REGISTER CONGESTION
Text in MML printoutsREGISTER CONGESTION
DescriptionNo free register is found during the register hunting phase.
Detected by
Default effect on the exchangeThe call is cleared in terminal and transit exchanges. The originating exchange connects a special information tone to the subscriber.
Possibility to change the default effectNot possible.
AlarmsNo alarms.
5.94 603H - NO RESPONSE FROM PARTNER PROGRAM BLOCK
Text in MML printoutsNO RESPONSE FROM CO-PROC
DescriptionA program block in the call control system block or in the signalling services system block has not been able to contact the partner block. The partner program block has not answered within the set time, or no connection has been established to the unit in ques-tion.
Program block
Explanation
CASSIG CASSIG sets the clear code when INREGI reports that the reservation of a register record has failed.
DN078927Issue 1-0
77
DX200 Clear Code List Clear codes
Id:0900d80580635beb
Detected by
Default effect on the exchangeThe call is cleared in terminal and transit exchanges. The originating exchange connects a special information tone to the subscriber.
Possibility to change the default effectNot possible.
AlarmsNo alarms.
5.95 604H - INTERNAL CALL LINK CONGESTION
Program block
Explanation
ASEPRB The following program blocks set the clear code when a service request receives no response within the time limit; ASEPRB, CASSIG, CFOPRB, CPLPRB, GCAPRB, IC1PRB, IC3PRB, IC6PRB, IDOPRB, IDXSCP, INREGI, LHSPRB, OC1PRB, OC3PRB, OC6PRB, OUREGI, RMAPRB, SI1PRB, SI5PRB, SI6PRB, SI7PRB and TPSPRB.
CASSIG –
CFOPRB –
CPLPRB –
GCAPRB –
IC1PRB –
IC3PRB –
IC6PRB –
IDOPRB –
IDXSCP –
INREGI –
LHSPRB –
OC1PRB –
OC3PRB –
OC6PRB –
OUREGI –
RMAPRB –
SI1PRB –
SI5PRB –
SI6PRB –
SI7PRB –
TPSPRB –
78 DN078927Issue 1-0
DX200 Clear Code List
Id:0900d80580635beb
Clear codes
Text in MML printoutsINT. CALL LINK CONGESTION
DescriptionNo free internal call links are available.
Detected by-
Default effect on the exchangeThe call is cleared in terminal and transit exchanges. The originating exchange connects a special information tone to the subscriber.
Possibility to change the default effectNot possible.
AlarmsNo alarms.
5.96 606H - CONFERENCE DEVICE CONGESTION
Text in MML printoutsCONFERENCE DEV.CONGESTION
DescriptionNo free conference devices are available. Conference devices are used when the operator intervenes in a proceeding call.
Detected by-
Default effect on the exchangeThe call is cleared in terminal and transit exchanges. The originating exchange connects a special information tone to the subscriber.
Possibility to change the default effectNot possible.
AlarmsNo alarms.
5.97 607H - POLARITY REVERSAL FAILURE
Text in MML printoutsPOLARITY REVERSAL FAILURE
DN078927Issue 1-0
79
DX200 Clear Code List Clear codes
Id:0900d80580635beb
DescriptionThe polarity reversal relay is broken.
Detected by-
Default effect on the exchangeThe call is cleared in terminal and transit exchanges. The originating exchange connects a special information tone to the subscriber.
Possibility to change the default effectNot possible.
AlarmsNo alarms.
5.98 608H - CHARGING NOT STARTED
Text in MML printoutsCHARGING NOT STARTED
DescriptionStarting of charging has failed.
Detected by
Default effect on the exchangeThe call is cleared in terminal and transit exchanges. The originating exchange connects a special information tone to the subscriber.
Possibility to change the default effectNot possible.
AlarmsNo alarms.
5.99 609H - CALL CLEARED BY MML
Program block
Explanation
CASSIG ICxPRB, TPSPRB or CASSIG sets the clear code when starting of charging fails.
ICXPRB ICxPRB, TPSPRB or CASSIG sets the clear code when starting of charging fails.
TPSPRB –
80 DN078927Issue 1-0
DX200 Clear Code List
Id:0900d80580635beb
Clear codes
Text in MML printoutsCALL CLEARED BY MML
DescriptionThe call has been cleared because of an operation and maintenance command.
Detected by
Default effect on the exchangeThe call is cleared in terminal and transit exchanges. The originating exchange connects a special information tone to the subscriber.
Possibility to change the default effectNot possible.
AlarmsNo alarms.
5.100 60BH - OVERLOAD CONGESTION
Text in MML printoutsOVERLOAD CONGESTION
DescriptionThe call set-up has been interrupted due to an overload of the unit or the entire exchange. New seizures cannot be received.
Detected by
Default effect on the exchangeThe call is cleared in terminal, transit and originating exchanges.
Possibility to change the default effectNot possible.
AlarmsNo alarms.
Program block
Explanation
CASSIG CASSIG or SIxPRB sets the clear code when message forced_clear is received.
SIXPRB –
Program block
Explanation
SI6PRB SI6PRB sets the clear code when the ticket service prevents the call set-up.
DN078927Issue 1-0
81
DX200 Clear Code List Clear codes
Id:0900d80580635beb
5.101 60DH - STAGE CIRCUIT CONGESTION
Text in MML printoutsSTAGE CIRCUIT CONGESTION
DescriptionNo free stage circuits are available between SSW and GSW.
Detected by-
Default effect on the exchangeThe call is cleared in terminal and transit exchanges. The originating exchange connects a special information tone to the subscriber.
Possibility to change the default effectNot possible.
AlarmsNo alarms.
5.102 60EH - UNIT RESTARTED
Text in MML printoutsUNIT RESTARTED
DescriptionThe call was cleared after the restart of the own unit. Most of the unit restarts are recorded with clear codes set on the time-outs of the call control time supervision.
Detected by-
Default effect on the exchangeThe call is cleared in terminal and transit exchanges. The originating exchange connects a special information tone to the subscriber.
Possibility to change the default effectNot possible.
AlarmsNo alarms.
5.103 60FH - SUBSCRIBER MODULE OR V5 INTERFACE FAILURE, CALL CLEARED
82 DN078927Issue 1-0
DX200 Clear Code List
Id:0900d80580635beb
Clear codes
Text in MML printoutsMOD OR V5 FAIL CALL CLEAR
DescriptionA plug-in unit has broken down, or it has been removed from subscriber module SUB-E, or the fault diagnosis has executed a forced test. Clear request has been received from the access node. SI2PRB sets this clear code if bearer channel is faulty due to access node internal failure.
Detected by
Default effect on the exchangeThe call is cleared in terminal and transit exchanges. The originating exchange connects a special information tone to the subscriber.
Possibility to change the default effectNot possible.
AlarmsNo alarms.
5.104 700H - LONG AON REQUEST
Text in MML printoutsLONG AON REQUEST
DescriptionLine signal AON REQUEST or OVERLONG ANSWER (8- or 0-traffic).
Detected by-
Default effect on the exchangeThe call is cleared in terminal and transit exchanges. The originating exchange connects a congestion tone to the subscriber.
Possibility to change the default effectNot possible.
AlarmsNo alarms.
Program block
Explanation
SI2PRB –
SI6PRB –
DN078927Issue 1-0
83
DX200 Clear Code List Clear codes
Id:0900d80580635beb
5.105 701H - REGISTER ANALYSIS FAILED
Text in MML printoutsREGISTER ANALYSIS FAILED
DescriptionThe register analysis has failed either due to unknown addressing in the analysis file, or because the analysis routine has returned an incorrect parameter.
Detected by
Default effect on the exchangeThe call is cleared in terminal and transit exchanges. The originating exchange connects a congestion tone to the subscriber.
Possibility to change the default effectNot possible.
AlarmsNo alarms.
Program block
Explanation
ICXPRB ICxPRB, OC6PRB, INREGI, OUREGI, LHSPRB or TPSPRB sets the clear code when the internal analysis of the program block (e.g. origin, dialling preanalysis, operator, facility, release, or end-of-selection analy-sis) fails.
INREGI ICxPRB, OC6PRB, INREGI, OUREGI, LHSPRB or TPSPRB sets the clear code when the internal analysis of the program block (e.g. origin, dialling preanalysis, operator, facility, release, or end-of-selection analy-sis) fails.
LHSPRB ICxPRB, OC6PRB, INREGI, OUREGI, LHSPRB or TPSPRB sets the clear code when the internal analysis of the program block (e.g. origin, dialling preanalysis, operator, facility, release, or end-of-selection analy-sis) fails.
OC6PRB ICxPRB, OC6PRB, INREGI, OUREGI, LHSPRB or TPSPRB sets the clear code when the internal analysis of the program block (e.g. origin, dialling preanalysis, operator, facility, release, or end-of-selection analy-sis) fails.
OUREGI ICxPRB, OC6PRB, INREGI, OUREGI, LHSPRB or TPSPRB sets the clear code when the internal analysis of the program block (e.g. origin, dialling preanalysis, operator, facility, release, or end-of-selection analy-sis) fails.
TPSPRB ICxPRB, OC6PRB, INREGI, OUREGI, LHSPRB or TPSPRB sets the clear code when the internal analysis of the program block (e.g. origin, dialling preanalysis, operator, facility, release, or end-of-selection analy-sis) fails.
84 DN078927Issue 1-0
DX200 Clear Code List
Id:0900d80580635beb
Clear codes
5.106 702H - QUEUEING TIME EXCEEDED
Text in MML printoutsQUEUEING TIME EXCEEDED
DescriptionThe queuing for resources has failed because the maximum queuing time has been exceeded.
Detected by
Default effect on the exchangeThe call is cleared in terminal and transit exchanges. The originating exchange connects a congestion tone to the subscriber.
Possibility to change the default effectNot possible.
AlarmsNo alarms.
5.107 704H - PARITY ERROR FROM PBRU/MFCU DEVICE
Text in MML printoutsPARITY ERR FROM PBRU/MFCU
DescriptionThere has been an error in interpreting a multifrequency character.
Program block
Explanation
IC6PRB IC6PRB, SI6PRB, INREGI or OUREGI sets the clear code when the resource (outgoing circuit, MFC or PBRU device) is not available within the queuing time limit.
INREGI IC6PRB, SI6PRB, INREGI or OUREGI sets the clear code when the resource (outgoing circuit, MFC or PBRU device) is not available within the queuing time limit.
OUREGI IC6PRB, SI6PRB, INREGI or OUREGI sets the clear code when the resource (outgoing circuit, MFC or PBRU device) is not available within the queuing time limit.
SI6PRB IC6PRB, SI6PRB, INREGI or OUREGI sets the clear code when the resource (outgoing circuit, MFC or PBRU device) is not available within the queuing time limit.
DN078927Issue 1-0
85
DX200 Clear Code List Clear codes
Id:0900d80580635beb
Detected by
Default effect on the exchangeThe call is cleared in terminal and transit exchanges. The originating exchange connects a congestion tone to the subscriber.
Possibility to change the default effectNot possible.
AlarmsNo alarms.
5.108 705H - MODULE OR V5 INTERFACE NOT AVAILABLE
Text in MML printoutsMOD OR V5 NOT AVAILABLE
DescriptionThe subscriber module's or V5 interface's WO-EX state has been changed, or the message connection to the module or V5 interface has broken.
Detected by
Default effect on the exchangeThe call is cleared in terminal and transit exchanges. The originating exchange connects a congestion tone to the subscriber.
Possibility to change the default effectNot possible.
AlarmsNo alarms.
Program block
Explanation
INREGI SI6PRB, INREGI or OUREGI sets the clear code when ACSERV sends the parity_err_from_pbru_mfcu or aux_mfc_parity_err message.
OUREGI –
SI6PRB SI6PRB, INREGI or OUREGI sets the clear code when ACSERV sends the parity_err_from_pbru_mfcu or aux_mfc_parity_err message.
Program block
Explanation
SI2PRB SI2PRB sets this clear code if pcm is not available in the V5.1 interface congestion or bearer channel reservation fails.
SI6PRB SI6PRB sets the clear code when the subscriber module's or V5 inter-face's state is not WO-EX.
86 DN078927Issue 1-0
DX200 Clear Code List
Id:0900d80580635beb
Clear codes
5.109 706H - CALL INTERRUPTED DURING REGISTER ANALYSIS
Text in MML printoutsCALL INTER REG ANALYSIS
DescriptionThe internal analysis of the call control has failed.
Detected by-
Default effect on the exchangeThe call is cleared in terminal and transit exchanges. The originating exchange connects a congestion tone to the subscriber.
Possibility to change the default effectNot possible.
AlarmsNo alarms.
5.110 707H - SUBSCRIBER MODULE RESTARTED
Text in MML printoutsSUBSCRIBER MODULE ºRESTART
DescriptionThe SSP program or the SUB, SUB-C, or SUB-D have been restarted, so the calls con-trolled by them will be cleared.
Detected by
Default effect on the exchangeThe call is cleared in terminal and transit exchanges. The originating exchange connects a congestion tone to the subscriber.
Possibility to change the default effectNot possible.
AlarmsNo alarms.
Program block
Explanation
SI6PRB SI6PRB sets the clear code when the state of the subscriber module is WO-RE and the old state is WO-EX.
DN078927Issue 1-0
87
DX200 Clear Code List Clear codes
Id:0900d80580635beb
5.111 70AH - FORCED CLEAR OF A CALL
Text in MML printoutsFORCED CLEAR OF A CALL
DescriptionThe call has been cleared due to the restart of CCSU, CAC, or LSU. This clear code is used if the release request of the call has been received from a refresher program block. The clear code is also used with PCM breaks, restarts of the LSP preprocessor, and LSU switchovers.
Detected by-
Default effect on the exchangeThe call is cleared in terminal and transit exchanges. The originating exchange connects a congestion tone to the subscriber.
Possibility to change the default effectNot possible.
AlarmsNo alarms.
5.112 70BH - MODEM ERROR
Text in MML printoutsMODEM ERROR
DescriptionThe modem DSP (Digital Signal Processing) software does not support the modem type detected. This clear code is set also if the modem DSP software does not detect a carrier signal or the carrier signal is lost during the call.
Detected by
Default effect on the exchangeThe exhange clears the call. A special tone is connected.
Possibility to change the default effectNot possible.
Program block
Explanation
MGAPRB MGAPRB sets the clear code according to an error type obtained from MRMPRB.
88 DN078927Issue 1-0
DX200 Clear Code List
Id:0900d80580635beb
Clear codes
AlarmsNo alarms.
5.113 70CH - OVERLOAD CONTROL SYSTEM ERROR
Text in MML printoutsOVERLOAD CONTROL SYS ERRO
DescriptionAn internal failure in the overload control system, which controls the amount of calls simultaneously accepted in the system.
Detected by-
Default effect on the exchangeThe call is cleared in terminal and transit exchanges. The originating exchange connects a congestion tone to the subscriber.
Possibility to change the default effectNot possible.
AlarmsNo alarms.
5.114 70DH - ANNOUNCEMENT SERVICE FAILURE
Text in MML printoutsANNOUNCEMENT ERROR
DescriptionUse of the announcement service has failed. The reason may be e.g. incorrect announcement creation data, capacity overflow, or hardware error. The announcement service examines the problem (and sets a suitable alarm, for example).
Detected by-
Default effect on the exchangeThe call is cleared in terminal and transit exchanges. The originating exchange connects a congestion tone to the subscriber.
Possibility to change the default effectNot possible.
AlarmsNo alarms.
DN078927Issue 1-0
89
DX200 Clear Code List Clear codes
Id:0900d80580635beb
5.115 70EH - CONFIGURATION ERROR
Text in MML printoutsCONFIGURATION ERROR
DescriptionConfiguration error in the exchange.
Detected by-
Default effect on the exchangeThe call is cleared in terminal and transit exchanges. The originating exchange connects a congestion tone to the subscriber.
Possibility to change the default effectNot possible.
AlarmsNo alarms.
5.116 710H - NO ANALYSIS FOR CARRIER ACCESS CODE
Text in MML printoutsNO ANA FOR OPER IDENTIF
DescriptionNo digit analysis created for the carrier access code.
Detected by
Default effect on the exchangeThe call is cleared in terminal and transit exchanges. The originating exchange connects a busy tone to the subscriber.
Possibility to change the default effectUsing facility routing (command group RE, parameter CDP), the call can be directed for reanalysis in tree 2CH both in terminal and transit exchanges. Using facility routing, the originating exchange can connect an audible tone to the subscriber.
Alarms2225
Program block
Explanation
ICXPRB The ICXPRB sets this clear code.
90 DN078927Issue 1-0
DX200 Clear Code List
Id:0900d80580635beb
Clear codes
5.117 711H - TARIFF NOT ACCEPTED BY TRANSIT EXCHANGE
Text in MML printoutsTRAN EX NOT ACCEPT TARIFF
DescriptionTariff is not accepted in transit exchange.
Detected by
Default effect on the exchangeCall is disconnected.
Possibility to change the default effectNot possible.
Alarms2300
5.118 712H - TARIFF NOT ACCEPTED BY ORIGINATING OR INTERWORKING EXCHANGE
Text in MML printoutsORIG EXCH NOT ACCPT TARIFF
DescriptionTariff is not accepted in originating or interworking exchange.
Detected by
Program block
Explanation
IC1PRB C1PRB, IC3PRB or IC6PRB set this code when tariff sent in CHG-message is not accepted in transit exchange.
IC3PRB C1PRB, IC3PRB or IC6PRB set this code when tariff sent in CHG-message is not accepted in transit exchange.
IC6PRB C1PRB, IC3PRB or IC6PRB set this code when tariff sent in CHG-message is not accepted in transit exchange.
Program block
Explanation
IC1PRB IC1PRB, IC3PRB or IC6PRB set this code when tariff sent in CHG-message is not accepted in originating or interworking exchange.
IC3PRB IC1PRB, IC3PRB or IC6PRB set this code when tariff sent in CHG-message is not accepted in originating or interworking exchange.
DN078927Issue 1-0
91
DX200 Clear Code List Clear codes
Id:0900d80580635beb
Default effect on the exchangeCall is disconnected.
Possibility to change the default effectNot possible.
Alarms2300
5.119 713H - NO ISUP ROUTE
Text in MML printoutsNO ISUP ROUTE
DescriptionThere is no ISUP route in the exchange that would meet the signalling requirements.
Detected by
Default effect on the exchangeThe call is cleared in terminal and transit exchanges. The originating exchange connects a congestion tone to the subscriber.
Possibility to change the default effectCall continueing may be changed by EOS analysis management -MML.
AlarmsNo alarms.
5.120 714H - ATTRIBUTE DIRECTED ROUTING MISMATCH
Text in MML printoutsATTRIB GENERAL MISMATCH
DescriptionThe route selection ended in congestion based on the attribute directed routing feature.
IC6PRB IC1PRB, IC3PRB or IC6PRB set this code when tariff sent in CHG-message is not accepted in originating or interworking exchange.
Program block
Explanation
Program block
Explanation
CMANAL CMANAL sets the clear code, because there is no ISUP route in the exchange that would meet the signalling requirements.
92 DN078927Issue 1-0
DX200 Clear Code List
Id:0900d80580635beb
Clear codes
Detected by
Default effect on the exchangeThe call is cleared.
Possibility to change the default effectThe parameters of the destination and subdestination can be redefined with the commands of the command groups RD, RK and RM.
AlarmsNo alarms.
5.121 715H - REQUESTED FACILITY WAS NOT AVAILABLE ON THE OUTGOING ROUTE
Text in MML printoutsFACIL NOT AVAIL ON ROUTE
DescriptionThe available routes do not support the required supplementary service(s). Depending on the call, certain characteristics can be required from the outgoing route, including the ability to support supplementary services needed in the call (like CUG, UUS1 or CCBS).
Detected by
Default effect on the exchangeRouting cannot be continued with the present requirements, but the call must be cleared.
Possibility to change the default effectThe call control process, ICxPRB, can set the required supplementary services as 'pre-ferred', which means that the supplementary services are not obligatory, but this has to be done in the original call attempt. The commands of the command group RR can also be used to modify the supplementary services defined for the route.
AlarmsNo alarms.
Program block
Explanation
CMANAL The CMANAL returns this clear code when requested by the ICxPRB, if the digit analysis ended in congestion.
Program block
Explanation
CMANAL The CMANAL returns this clear code when requested by the ICxPRB, if the required supplementary service(s) were not found.
DN078927Issue 1-0
93
DX200 Clear Code List Clear codes
Id:0900d80580635beb
5.122 716H - REQUESTED BEARER CAPABILITY COULD NOT BE FULFILLED ON THE ROUTE
Text in MML printoutsBEARER CAP NOT RECEIVED
DescriptionThe call cannot be routed to available routes, as the route did not have the required bearer capability. The call can require e.g. an unrestricted digital route, but the available routes only offer speech transfer. This means that the call must be cleared as the required service cannot be provided.
Detected by
Default effect on the exchangeRouting cannot be continued with the present requirements, but the call must be cleared.
Possibility to change the default effectThe call control process, ICxPRB, can set a secondary bearer capability requirement, which is used if the primary bearer capability could not be provided, but this has to be done in the original call attempt. The operator can also modify the bearer capability with the commands of the command group RR.
AlarmsNo alarms.
5.123 718H - DIGIT ANALYSIS IN CENTRAL MEMORY RESULTED IN CONGESTION
Text in MML printoutsCM ANALYSIS CONGESTION
DescriptionThe digit analysis has resulted in a congestion due to a restriction found in the analysis: the destination has been blocked, an alternative subdestination has been bypassed, a subdestination has been bypassed, a subdestination has been blocked, overflow from the subdestination has been restricted, the use of the subdestination has been restricted, or a combination of the aforementioned. This clear code is used also when a call has been cleared because the maximum amount of satellites per one call has exceeded. Releasing a call due to these causes is usually a desired consequence. This can be modified with the commands of the command groups RD, RK and RM. This clear
Program block
Explanation
CMANAL The CMANAL returns this clear code when requested by the ICxPRB, if the required bearer capability was not found.
94 DN078927Issue 1-0
DX200 Clear Code List
Id:0900d80580635beb
Clear codes
code is not, however, used when the cause of the congestion can be expressed with the clear codes BEARER CAP NOT RECEIVED (0716H), FACIL NOT AVAIL ON ROUTE (0715H), PROHIBITED DIALLING (0C01H) or ATTRIBUTE GENERAL MISMATCH (0714H), or in analysis error situations, when the clear code is FILE ERROR (0509H).
Detected by
Default effect on the exchangeRouting cannot be continued as the situation is irreversible, but the call must be cleared.
Possibility to change the default effectThe parameters of the destination and subdestination can be redefined with the commands of the command groups RD, RK and RM.
AlarmsNo alarms.
5.124 719H - NO RESOURCE AVAILABLE FOR CALL
Text in MML printoutsNO RESOURCE FOR CALL
DescriptionThe clear code is set when there is no resource for call, e.g. hand reservation fails.
Detected by
Program block
Explanation
CMANAL The CMANAL returns this clear code when requested by the ICxPRB, if the digit analysis ended in congestion.
Program block
Explanation
CFOPRB SIXPRB,ICXPRB,OCXPRB,RMAPRB, DPNPRB,CFOPRB,PRK-PRB,IPOPRB set the clear code when there is no resource for the call, e.g. hand reservation fails in the call setup phase.
DPNPRB –
ICXPRB –
IDOPRB –
OCXPRB –
PRKPRB –
RMAPRB –
SIXPRB SIXPRB,ICXPRB,OCXPRB,RMAPRB,DPNPRB,CFOPRB,PRK-PRB,IPOPRB set the clear code when there is no resource for the call, e.g. hand reservation fails in the call setup phase.
DN078927Issue 1-0
95
DX200 Clear Code List Clear codes
Id:0900d80580635beb
Default effect on the exchangeIC6PRB, IC1PRB and IC3PRB starts alternative routing.
Possibility to change the default effectNot possible.
Alarms2668
5.125 71AH - IDENTIFIED CHANNEL NOT EXIST
Text in MML printoutsIDENTIFIED CH NOT EXIST
DescriptionA PBX has requested a channel which is not created.
Detected by
Default effect on the exchangeThe call from an access is not accepted.
Possibility to change the default effectNot possible.
AlarmsNo alarms.
5.126 71BH - REQUESTED CHANNEL NOT AVAILABLE
Text in MML printoutsREQ CHANNEL NOT AVAILABLE
DescriptionA PBX has requested a channel which is not available. It can be for example busy or not in use.
Program block
Explanation
SI1PRB Detected by SI1PRB when the requested channel is not created.
96 DN078927Issue 1-0
DX200 Clear Code List
Id:0900d80580635beb
Clear codes
Detected by
Default effect on the exchangeA call from an access is not accepted.
Possibility to change the default effectNot possible.
AlarmsNo alarms.
5.127 71CH - PACKET CONTROL UNIT CONGESTION
Text in MML printoutsPCU CONGESTION
DescriptionNo DSP (Digital Signal Processing) or ISDN resource available for the call in the PCU (Packet Control Unit) plug-in unit.
Detected by
Default effect on the exchangeThe exhange starts hunting for a new free circuit from the route.
Possibility to change the default effectNot possible.
AlarmsNo alarms.
5.128 71DH - POINT-TO-POINT PROTOCOL ERROR
Text in MML printoutsPPP ERROR
Program block
Explanation
SI1PRB Detected by SI1PRB when the requested channel is not available (busy, not in use).
Program block
Explanation
MGAPRB MGAPRB sets the clear code according to the error type obtained from MRMPRB.
DN078927Issue 1-0
97
DX200 Clear Code List Clear codes
Id:0900d80580635beb
DescriptionPoint-to-Point (PPP) Protocol has not been started or a failure in PPP-protocol has occured.
Detected by
Default effect on the exchangeThe exhange clears the call. A special tone is connected.
Possibility to change the default effectNot possible.
AlarmsNo alarms.
5.129 801H - LENGTH OF ORIGINAL CALLED SUBSCRIBER NUMBER EXCEEDED
Text in MML printoutsORIG.B-NO LENGTH EXCEEDED
DescriptionThe original called subscriber's (B subscriber's) number is too long. The original called subscriber's number received from the trunk circuit has been too long.
Detected by-
Default effect on the exchangeThe call is cleared in terminal and transit exchanges. The originating exchange connects a congestion tone to the subscriber.
Possibility to change the default effectNot possible.
AlarmsNo alarms.
5.130 802H - LENGTH OF CALLING SUBSCRIBER NUMBER EXCEEDED
Program block
Explanation
MGAPRB MGAPRB sets the clear code according to the error information obtained from the Point-to-Point Protocol program block.
98 DN078927Issue 1-0
DX200 Clear Code List
Id:0900d80580635beb
Clear codes
Text in MML printoutsA-NUMBER LENGTH EXCEEDED
DescriptionThe calling subscriber's (A subscriber's) number is too long. The original calling sub-scriber's number received from the trunk circuit has been too long.
Detected by
Default effect on the exchangeThe call is cleared in terminal and transit exchanges. The originating exchange connects a congestion tone to the subscriber.
Possibility to change the default effectNot possible.
AlarmsNo alarms.
5.131 803H - INVALID CALLING SUBSCRIBER CATEGORY
Text in MML printoutsINVALID SUBSCR. A CATEGO
DescriptionThe category data of the calling subscriber (A-subscriber) received from the incoming circuit is invalid.
Detected by
Default effect on the exchangeThe call is cleared in terminal and transit exchanges. The originating exchange carries out a digit re-analysis in tree 32H.
Program block
Explanation
INREGI INREGI sets the clear code when a too long A-subscriber number is received from R2 signalling.
Program block
Explanation
INREGI INREGI or OUREGI sets the clear code when the subscriber category received from R2 signalling cannot be identified.
OUREGI –
DN078927Issue 1-0
99
DX200 Clear Code List Clear codes
Id:0900d80580635beb
Possibility to change the default effectUsing facility routing (command group RE, parameter CCF), transit and terminal exchanges can carry out a digit re-analysis in tree 32H or connect an audible tone. Using facility routing, the originating exchange can connect an audible tone to the subscriber.
AlarmsNo alarms.
5.132 804H - OUTGOING CIRCUIT CONGESTION
Text in MML printoutsOUTGOING CIRCUIT CONGEST
DescriptionAll circuits of the hunted external route are busy.
Detected by
Default effect on the exchangeThe call is cleared in terminal and transit exchanges. The originating exchange carries out a digit re-analysis in interception tree.
Possibility to change the default effectBy using facility routing, terminal and transit exchanges can carry out a digit re-analysis in interception tree or connect an audible tone. Interception tree 2DH (command group RE, parameter CFC).
AlarmsNo alarms.
5.133 806H - IDENTITY OF CALLING SUBSCRIBER IS NOT AVAILABLE
Text in MML printoutsA IDENTITY NOT AVAILABLE
Program block
Explanation
ICXPRB INREGI or ICxPRB sets the clear code when the outgoing circuit group is in BARRED state or all outgoing circuits are reserved on the used route. SI2PRB sets this clear code in the V5.2 interface if circuit reservation fails.
INREGI –
SI2PRB –
100 DN078927Issue 1-0
DX200 Clear Code List
Id:0900d80580635beb
Clear codes
DescriptionThe identity of the calling subscriber (A-subscriber) has not been received from the incoming circuit. The termination of the call set-up phase requires the identity of the A-subscriber.
Detected by-
Default effect on the exchangeThe call is cleared in terminal and transit exchanges. The originating exchange connects a congestion tone to the subscriber.
Possibility to change the default effectNot possible.
AlarmsNo alarms.
5.134 809H - ERRONEOUS MFC SIGNAL FROM OUTGOING CIRCUIT
Text in MML printoutsMFC ERROR SIGN FROM OUT
DescriptionThe MFC signal received from the outgoing circuit does not comply with the signals in use in the signalling system.
Detected by
Default effect on the exchangeThe call is cleared in terminal and transit exchanges. The originating exchange connects a congestion tone to the subscriber.
Possibility to change the default effectNot possible.
AlarmsNo alarms.
Program block
Explanation
OUREGI OUREGI sets the clear code when a faulty MFC signal has been received from the outgoing connection.
DN078927Issue 1-0
101
DX200 Clear Code List Clear codes
Id:0900d80580635beb
5.135 80AH - ERRONEOUS MFC SIGNAL FROM INCOMING CIRCUIT
Text in MML printoutsMFC ERROR SIGN FROM INCOM
DescriptionThe MFC signal received from the incoming circuit does not comply with the signals in use in the signalling system.
Detected by
Default effect on the exchangeThe call is cleared in terminal and transit exchanges. The originating exchange connects a congestion tone to the subscriber.
Possibility to change the default effectNot possible.
AlarmsNo alarms.
5.136 80BH - NO B-NUMBERS TO SEND TO OUTGOING CIRCUIT
Text in MML printoutsNO B-NUMB TO SEND TO OG
DescriptionAn attempt has been made to start signalling without sending it any digit to be analysed.
Detected by
Default effect on the exchangeThe call is cleared in terminal and transit exchanges. The originating exchange connects a congestion tone to the subscriber.
Program block
Explanation
INREGI INREGI sets the clear code when a faulty MFC signal has been received from the incoming circuit.
Program block
Explanation
OUREGI OUREGI sets the clear code when it has no selection available with which to start outgoing signalling.
102 DN078927Issue 1-0
DX200 Clear Code List
Id:0900d80580635beb
Clear codes
Possibility to change the default effectNot possible.
AlarmsNo alarms.
5.137 80CH - UNKNOWN DECADIC SIGNAL FROM INCOMING CIRCUIT
Text in MML printoutsUNKNOWN DECADIC SIGNAL
DescriptionAn unknown overdecadic signal has been received from the incoming circuit.
Detected by
Default effect on the exchangeThe call is cleared in terminal and transit exchanges. The originating exchange connects a congestion tone the subscriber.
Possibility to change the default effectNot possible.
AlarmsNo alarms.
5.138 80DH - OUTGOING CIRCUIT OUT OF ORDER
Text in MML printoutsOUT CIRCUIT OUT OF ORDER
DescriptionThe state data on the outgoing circuit is contradictory to the marker switching data; con-sequently the seizure is rejected. Reasons for contradiction: Because of a PCM distur-bance, the outgoing circuit is in fault filtering state but has not yet been barred from hunting. The circuit had already been hunted before the PCM disturbance. Signalling of the circuit is not in idle state and the circuit has been hunted before barring.
Detected by-
Program block
Explanation
INREGI INREGI sets the clear code when an undefined decadic signal has been received from the incoming circuit.
DN078927Issue 1-0
103
DX200 Clear Code List Clear codes
Id:0900d80580635beb
Default effect on the exchangeThe call is cleared in terminal and transit exchanges. The originating exchange carries out a digit re-analysis in interception tree.
Possibility to change the default effectNot possible. Interception tree 2EH.
AlarmsNo alarms.
5.139 80EH - INCOMING CIRCUIT OUT OF ORDER
Text in MML printoutsIN CIRCUIT OUT OF ORDER
DescriptionAn unknown line signal has been received from the incoming circuit, and a call in the set-up phase is interrupted. If an unknown line signal is received during the conversation phase, the connection is cleared.
Detected by-
Default effect on the exchangeThe call is cleared in terminal and transit exchanges. The originating exchange carries out a digit re-analysis in interception tree. Interception tree 2EH. Interception tree 2DH (command group RE, parameter CFC).
Possibility to change the default effectNot possible.
AlarmsNo alarms.
5.140 80FH - CIRCUIT CONGESTION
Text in MML printoutsCIRCUIT CONGESTION
DescriptionCongestion or another equivalent signal or message has been received from the outgoing circuit during the call set-up phase.
Detected by-
104 DN078927Issue 1-0
DX200 Clear Code List
Id:0900d80580635beb
Clear codes
Default effect on the exchangeThe call is cleared in terminal and transit exchanges. The originating exchange carries out a digit re-analysis in an interception tree.
Possibility to change the default effectUsing facility routing, terminal and transit exchanges can carry out a digit re-analysis in an interception tree or connect an audible tone. Using facility routing, the originating exchange can connect an audible tone to the subscriber. Interception tree 2DH (command group RE, parameter CFC). Interception tree 32H (command group RE, parameter CCF).
AlarmsNo alarms.
5.141 810H - FACILITY NOT SUPPORTED
Text in MML printoutsFACILITY NOT SUPPORT
DescriptionThe requested service is not supported in the public network.
Detected by-
Default effect on the exchangeIn the transit and terminal exchanges the call is cleared. In the originating exchange a congestion tone is connected to the subscriber.
Possibility to change the default effectNot possible.
AlarmsNo alarms.
5.142 811H - NETWORK FAILURE
Text in MML printoutsNETWORK FAILURE
DescriptionA network element cannot perform an operation because of the failure of another network element.
Detected by-
DN078927Issue 1-0
105
DX200 Clear Code List Clear codes
Id:0900d80580635beb
Default effect on the exchangeThe call is cleared in terminal and transit exchanges. The originating exchange carries out a digit re-analysis in tree 2DH (command group RE, parameter CFC).
Possibility to change the default effectUsing facility routing, terminal and transit exchanges can carry out a digit re-analysis in tree 2DH or connect an audible tone. Using facility routing, the originating exchange can connect an audible tone to the subscriber.
AlarmsNo alarms.
5.143 813H - SWITCHING EQUIPMENT CONGESTION
Text in MML printoutsSWITCHING EQUI CONGESTION
DescriptionA call clear received from the network; originating exchange detected that congestion was caused by hunting for exchange device.
Detected by-
Default effect on the exchangeThe call is cleared in terminal and transit exchanges. The originating exchange connects a congestion tone to the subscriber.
Possibility to change the default effectUsing facility routing (command group RE, parameter CSC), terminal and transit exchanges can carry out a digit re-analysis in tree 31H or connect an audible tone. Using facility routing, the originating exchange can carry out a digit re-analysis in tree 31H.
AlarmsNo alarms.
5.144 814H - CIRCUIT GROUP CONGESTION
Text in MML printoutsCIRCUIT GROUP CONGESTION
DescriptionCall clear received from the network; congestion on the circuit group.
Detected by-
106 DN078927Issue 1-0
DX200 Clear Code List
Id:0900d80580635beb
Clear codes
Default effect on the exchangeThe call is cleared in terminal and transit exchanges. The originating exchange carries out a digit re-analysis in interception tree.
Possibility to change the default effectUsing facility routing terminal and transit exchanges can carry out a digit re-analysis in interception tree or connect an audible tone. Using facility routing, the originating exchange can connect an audible tone to the subscriber. Interception tree 2EH (command group RE, parameter CRO). Interception tree 2DH (command group RE, parameter CFC).
AlarmsNo alarms.
5.145 815H - ACCESS BARRED TO THE CALLED SUBSCRIBER
Text in MML printoutsB ACCESS BARRED
DescriptionAn access barred message has been received which indicates that the call could not be connected to the subscriber line indicated by the received number. This may occur if the called connection belongs to a closed user group, or subscriber facility "incoming call barring" has been activated.
Detected by-
Default effect on the exchangeThe call is cleared in terminal and transit exchanges. The originating exchange carries out a digit re-analysis in tree 35H.
Possibility to change the default effectUsing facility routing (command group RE, parameter CAB), terminal and transit exchanges can carry out a digit re-analysis in tree 35H or connect an audible tone. Using facility routing, the originating exchange can connect an audible tone to the subscriber.
AlarmsNo alarms.
5.146 816H - CALL FAILED, SEND SPECIAL INFORMATION TONE
Text in MML printoutsCALL UNSUC SEND INFO TONE
DN078927Issue 1-0
107
DX200 Clear Code List Clear codes
Id:0900d80580635beb
DescriptionInformation "send special information tone" has been received from the network.
Detected by-
Default effect on the exchangeThe call is cleared in terminal and transit exchanges. The originating exchange carries out a digit re-analysis in tree 34H.
Possibility to change the default effectUsing facility routing (command group RE, parameter CST), the call can be directed for reanalysis in tree 34H both in terminal and transit exchanges. Using facility routing, the originating exchange can connect an audible tone to the subscriber.
AlarmsNo alarms.
5.147 817H - NETWORK, UNALLOCATED NUMBER
Text in MML printoutsN-UNALLOCATED NUMBER
DescriptionInformation "unallocated number" has been received from the network.
Detected by-
Default effect on the exchangeThe call is cleared in terminal and transit exchanges. The originating exchange carries out a digit re-analysis in tree 2AH.
Possibility to change the default effectUsing facility routing (command group RE, parameter CUN), terminal and transit exchanges can carry out a digit re-analysis in tree 2AH or connect an audible tone. Using facility routing, the originating exchange can connect an audible tone to the sub-scriber.
AlarmsNo alarms.
5.148 818H - NETWORK, LINE OUT OF SERVICE
Text in MML printoutsN-LINE OUT OF SERVICE
108 DN078927Issue 1-0
DX200 Clear Code List
Id:0900d80580635beb
Clear codes
DescriptionInformation "line out of service or unallocated" has been received from the network. SI2PRB sets this clear code: in V5 interface congestion if state or user port is not avail-able or bearer channel reservation fails.
Detected by
Default effect on the exchangeThe call is cleared in terminal and transit exchanges. The originating exchange carries out a digit re-analysis in interception tree.
Possibility to change the default effectUsing facility routing the terminal and transit exchanges can carry out a digit re-analysis in interception tree or connect an audible tone. Using facility routing, the originating exchange can connect an audible tone to the subscriber. Interception tree 2FH (command group RE, parameter CFB).
AlarmsNo alarms.
5.149 819H - NETWORK, SUBSCRIBER NUMBER CHANGED
Text in MML printoutsN-SUBSCRIB NUMBER CHANGED
DescriptionInformation "subscriber number changed" has been received from the network.
Detected by-
Default effect on the exchangeThe call is cleared in terminal and transit exchanges. The originating exchange does reanalysis in the interception tree.
Possibility to change the default effectUsing facility routing (command group RE, parameter CSN), the call can be directed for reanalysis in tree 29H both in terminal and transit exchanges.
AlarmsNo alarms.
Program block
Explanation
SI2PRB SI2PRB, SI6PRB
SI6PRB –
DN078927Issue 1-0
109
DX200 Clear Code List Clear codes
Id:0900d80580635beb
5.150 81AH - CONGESTION IN TERMINAL EXCHANGE
Text in MML printoutsTERMINAL CONGESTION
DescriptionCongestion has been detected in the terminal exchange. Rerouting the call is not pos-sible. The reason can be, for example, that hunting a circuit for a mobile terminating call has failed.
Detected by
Default effect on the exchangeThe call is cleared in terminal and transit exchanges. The originating exchange connects a congestion tone to the subscriber.
Possibility to change the default effectNot possible.
AlarmsNo alarms.
5.151 81DH - CONGESTION IN INTERNATIONAL CALL
Text in MML printoutsINTERNATIONAL CONGESTION
DescriptionThe TUP's International Congestion message has been received from the network.
Detected by-
Default effect on the exchange–
Possibility to change the default effectNot possible.
AlarmsNo alarms.
Program block
Explanation
ICXPRB –
110 DN078927Issue 1-0
DX200 Clear Code List
Id:0900d80580635beb
Clear codes
5.152 81EH - CONTROLLED NOT READY
Text in MML printoutsCONTROLLED NOT READY
DescriptionThe CONTROLLED NOT READY message of inter-exchange TUP signalling has been received from the network. This signalling is in use in Italy The DTE-controlled not_ready cause code received from the NUP signalling.
Detected by-
Default effect on the exchangeThe call is cleared in terminal and transit exchanges. The originating exchange connects a special information tone to the subscriber.
Possibility to change the default effectNot possible.
AlarmsNo alarms.
5.153 81FH - NETWORK, OVERLOAD CONGESTION
Text in MML printoutsNETWORK OVERLOAD
DescriptionAn overload message has been received from the network.
Detected by
Default effect on the exchangeThe call is rerouted to an alternative route. If it is not possible, the call is cleared with this clear code. The function to the network depends on the signalling used.
Possibility to change the default effectNot possible.
Program block
Explanation
SI4PRB The SI4PRB or the SI7PRB sets this clear code when it has received an overload/OLM message from the network after an IAM/IFAM has been sent.
SI7PRB –
DN078927Issue 1-0
111
DX200 Clear Code List Clear codes
Id:0900d80580635beb
AlarmsNo alarms.
5.154 820H - NETWORK MESSAGE CONTENT ERROR
Text in MML printoutsNETWORK MSG CONTENT ERROR
DescriptionInconsistent network message received.
Detected by
Default effect on the exchangeThe call is cleared in terminal and transit exchanges. The originating exchange connects a congestion tone to the subscriber.
Possibility to change the default effectNot possible.
AlarmsNo alarms.
5.155 821H - INVALID TRANSIT NETWORK SELECTION
Text in MML printoutsINVALID TRANSIT NETWORK
DescriptionThe chosen transit network is erroneous or it does not exist.
Detected by
Default effect on the exchange–
Program block
Explanation
SI4PRB SI4PRB or SI7PRB sets this clear code when it has noticed an incon-sistent network message.
SI7PRB –
Program block
Explanation
SI7PRB –
112 DN078927Issue 1-0
DX200 Clear Code List
Id:0900d80580635beb
Clear codes
Possibility to change the default effectNot possible.
AlarmsNo alarms.
5.156 822H - RECOVERY ON TIMER EXPIRY
Text in MML printoutsRECOVERY ON TIMER EXPIRY
DescriptionRecovery from fault situation has been initiated within network according to ISUP (Q.767)
Detected by
Default effect on the exchangeThe call is cleared in terminal and transit exchanges. The originating exchange connects a busy tone to the subscriber.
Possibility to change the default effectNot possible.
AlarmsNo alarms.
5.157 824H - PCM FAULTY
Text in MML printoutsPCM FAULTY
DescriptionThis code is set when the system has found that PCM is faulty and has asked the sig-nalling to clear the call. The reason may be an internal or external failure: an ET failure, a transmission link failure etc. An alarm has also been set to indicate call clearing.
Detected by
Program block
Explanation
SI7PRB –
Program block
Explanation
SI2PRB –
DN078927Issue 1-0
113
DX200 Clear Code List Clear codes
Id:0900d80580635beb
Default effect on the exchangeThe call from an access is not accepted. The originating exchange connects a conges-tion tone to the subscriber.
Possibility to change the default effectNot possible.
Alarms2202, 2204, 2900, 2902, 2909, 2910, 2912, 2915
5.158 828H - CONGESTION FROM NATIONAL NETWORK
Text in MML printoutsN NATIONAL CONGESTION
DescriptionThe National Network Congestion message (ITUP) has been received from the network.
Detected by
Default effect on the exchangeThe call is cleared in the terminal and transit exchanges. The originating exchange connects an announcement or an audible tone to the subscriber.
Possibility to change the default effectUsing facility routing, the terminal and transit exchanges can carry out a digit re-analysis in the interception tree 32H (command group RE, parameter CCF).
AlarmsNo alarms.
SI3PRB –
SI4PRB –
SI5PRB –
SI7PRB –
SI8PRB –
Program block
Explanation
Program block
Explanation
SI5PRB The SI5PRB sets this clear code when it receives the NNC message from the network.
114 DN078927Issue 1-0
DX200 Clear Code List
Id:0900d80580635beb
Clear codes
5.159 829H - DIGITAL CIRCUIT MULTIPLICATION EQUIPMENT CONGESTION
Text in MML printoutsDCME CONGESTION
DescriptionThis clear code is set when the call terminates to outgoing call congestion which is caused by the missing traffic transfer capacity in a DCME and no other alternative route is available.
Detected by
Default effect on the exchangeThe call is cleared in terminal and transit exchanges. The originating exchange carries out a digit re-analysis in interception tree.
Possibility to change the default effectBy using facility routing, the terminal and transit exchanges can carry out a digit re-analysis in an interception tree or connect an audible tone. Interception tree 2DH (command group RE, parameter CFC).
AlarmsNo alarms.
5.160 830H - NUMBER PORTABILITY
Text in MML printoutsPORTED NUMBER NETWORK
DescriptionThe routing number of the subscriber has changed because the subscriber has moved to the network of another operator.
Program block
Explanation
IC1PRB Q50PRB sets this clear code when RMAPRB has requested DCME. RMAPRB returns this clear code to IC1PRB, IC3PRB or IC6PRB.
IC3PRB –
IC6PRB –
Q50PRB –
RMAPRB –
DN078927Issue 1-0
115
DX200 Clear Code List Clear codes
Id:0900d80580635beb
Detected by
Default effect on the exchangeThe call is cleared in terminal and transit exchanges. The originating exchange carries out a digit re-analysis in interception tree 32H.
Possibility to change the default effectUsing facility routing terminal and transit exchanges can carry out a digit re-analysis in the interception tree 32H ( command group RE, parameter CCF ) or connect an audible tone to the subscriber. Using facility routing the originating exchange can connect an audible tone to the subscriber. Using EOS -analysis handling ( MML command group RX ) the analysis tree can be changed.
AlarmsNo alarms.
5.161 832H - ROUTING ERROR
Text in MML printoutsROUTING ERROR
DescriptionError in routing. The hop counter has exhausted in the network. The hop counter has an initial (maximal) value, which is decreased in every intermediate exchange. When it becomes zero, the call is cleared and an alarm is given. The hop counter helps to prevent looping between networks in the multicarrier environment.
Detected by
Default effect on the exchangeThe call is released.
Possibility to change the default effectNot possible.
Alarms1206
Program block
Explanation
INXPRB SI7PRB SI1PRB INXPRB
SI1PRB –
SI7PRB –
Program block
Explanation
SI7PRB SI7PRB sets this release code, after getting #25 cause code.
116 DN078927Issue 1-0
DX200 Clear Code List
Id:0900d80580635beb
Clear codes
5.162 833H - DIGITAL CIRCUIT MULTIPLICATION EQUIPMENT FAILURE
Text in MML printoutsDCME FAILURE
DescriptionDX200 has received a line signal Out-of-service from DCME. A call on that circuit is cleared. Q50PRB informs SS-program block involved about this with a message dcme_fail_release_s.
Detected by
Default effect on the exchangeThe call is cleared. An announcement or a tone is connected to the subscriber.
Possibility to change the default effectUsing facility routing, terminal and transit exchanges can carry out a digit re-analysis or connect an audible tone. Using facility routing, the originating exchange can connect an audible tone to the subscriber. Interception tree 2DH (command group RE, parameter CFC).
Alarms2997
5.163 851H - TRAFFIC TO CONGESTED DESTINATION POINT CODE RESTRICTED BY SIGNALLING
Text in MML printoutsSCC CONGESTION
DescriptionThe exchange selects calls randomly according to the current clearing level, and requests signalling to clear the selected calls. There can be national (0-3) or interna-tional (0-5) clearing levels, for which the user can define a clearing percentage (the greater the level the higher the percentage). The Signalling Congestion Control system (SCC) restricts traffic to the destination point because of congestion on the signalling link, or because the partner end has requested traffic restriction with a TFC message.
Program block
Explanation
Q50PRB SI5PRB, SI7PRB
SI5PRB –
SI7PRB –
DN078927Issue 1-0
117
DX200 Clear Code List Clear codes
Id:0900d80580635beb
Detected by
Default effect on the exchangeThis causes clearing of call, and no repeat attempts are allowed.
Possibility to change the default effectNot possible.
AlarmsNo alarms.
5.164 900H - NO MF FORWARD SIGNAL
Text in MML printoutsNO MF FORWARD SIGNAL
DescriptionIn multifrequency signalling, no MF forward signal has been received from the incoming circuit during the time supervision T1 = 350 ms. The MF signal 15 is sent to the incoming circuit.
Detected by
Default effect on the exchangeThe call is cleared in terminal and transit exchanges. The originating exchange connects a special information tone to the subscriber.
Possibility to change the default effectNot possible.
AlarmsNo alarms.
5.165 901H - TOO LONG MF FORWARD SIGNAL
Text in MML printoutsTOO LONG MF FORWARD SIGNL
Program block
Explanation
SI7PRB –
Program block
Explanation
INREGI INREGI sets the clear code when ACSERV sends message aux_no_forward_char (6539).
118 DN078927Issue 1-0
DX200 Clear Code List
Id:0900d80580635beb
Clear codes
DescriptionIn multifrequency signalling, an MF signal with a duration of >= 1 - 2 s has been received from the incoming circuit.
Detected by
Default effect on the exchangeThe call is cleared in terminal and transit exchanges. The originating exchange connects a special information tone to the subscriber.
Possibility to change the default effectNot possible.
AlarmsNo alarms.
5.166 905H - TOO LONG MF BACKWARD SIGNAL
Text in MML printoutsTOO LONG MF BACKWARD SIGN
DescriptionIn multifrequency signalling, an MF signal with a duration of >= 3 - 4 s has been received from the outgoing circuit.
Detected by
Default effect on the exchangeThe call is cleared in terminal and transit exchanges. The originating exchange connects a special information tone to the subscriber.
Possibility to change the default effectNot possible.
AlarmsNo alarms.
Program block
Explanation
INREGI INREGI sets the clear code when ACSERV sends message aux_long_char_s (6540).
Program block
Explanation
OUREGI OUREGI sets the clear code when CASSIG sends message long_char_s (0081).
DN078927Issue 1-0
119
DX200 Clear Code List Clear codes
Id:0900d80580635beb
5.167 90CH - PREMATURE ACKNOWLEDGEMENT TO SEIZURE IN OUTGOING CIRCUIT
Text in MML printoutsPREMAT SEIZ ACK OUT CRCT
DescriptionAcknowledgement to a seizure sent on an outgoing circuit has been received before the expiration of the safety time specified for the signalling.
Detected by
Default effect on the exchangeThe call is cleared in terminal and transit exchanges. The originating exchange connects a special information tone to the subscriber.
Possibility to change the default effectNot possible.
AlarmsNo alarms.
5.168 90EH - PREMATURE ANSWER
Text in MML printoutsPREMATURE ANSWER
DescriptionCASSIG-B has received an answer signal from the outgoing circuit during the register phase. The register has not yet received the B-subscriber's (called subscriber) state data from the outgoing circuit.
Detected by
Default effect on the exchangeThe call is cleared in terminal and transit exchanges. The originating exchange connects a special information tone to the subscriber.
Program block
Explanation
CASSIG –
Program block
Explanation
OUREGI OUREGI sets the clear code when CASSIG sends message premature_answer_s.
120 DN078927Issue 1-0
DX200 Clear Code List
Id:0900d80580635beb
Clear codes
Possibility to change the default effectNot possible.
AlarmsNo alarms.
5.169 90FH - ANSWER AFTER B BUSY
Text in MML printoutsANSWER AFTER B BUSY
DescriptionAn answer has been received from the outgoing circuit after the called subscriber busy information.
Detected by-
Default effect on the exchangeThe call is cleared in terminal and transit exchanges. The originating exchange connects a special information tone to the subscriber.
Possibility to change the default effectNot possible.
AlarmsNo alarms.
5.170 A01H - CLEARED FORWARD (SEIZING ACKNOWLEDGED SIGNAL MISSING)
Text in MML printoutsIDLE CONTROL END MISSED
DescriptionNo seizing acknowledged signal has been received from the outgoing circuit within 400 ms from the sending of the seizure.
Detected by-
Default effect on the exchangeThe call is cleared in terminal and transit exchanges. The originating exchange connects a special information tone to the subscriber.
Possibility to change the default effectNot possible.
DN078927Issue 1-0
121
DX200 Clear Code List Clear codes
Id:0900d80580635beb
AlarmsNo alarms.
5.171 A02H - INVALID MESSAGE FROM TRUNK CIRCUIT
Text in MML printoutsINVALID TRUNK CRCT MSG
DescriptionAn invalid message from a trunk circuit. The message is unspecified or the message type is nonexistent or not implemented.
Detected by-
Default effect on the exchangeThe call is cleared in terminal and transit exchanges. The originating exchange connects a special information tone to the subscriber.
Possibility to change the default effectNot possible.
AlarmsNo alarms.
5.172 A03H - INTERWORKING FAILED
Text in MML printoutsINTERWORKING FAILED
DescriptionInterworking has taken place with a network which does not function in the defined way.
Detected by-
Default effect on the exchangeThe call is cleared in terminal and transit exchanges. The originating exchange carries out a digit re-analysis in tree 34H.
Possibility to change the default effectUsing facility routing (command group RE, parameter CST), the transit and terminal exchanges can connect an audible tone to the incoming circuit or carry out a digit re-analysis in tree 34H. Using facility routing, the originating exchange can connect an audible tone to the subscriber.
122 DN078927Issue 1-0
DX200 Clear Code List
Id:0900d80580635beb
Clear codes
AlarmsNo alarms.
5.173 A04H - TRUNK CIRCUIT PROTOCOL ERROR
Text in MML printoutsTRUNK CRCT PROTOCOL ERROR
DescriptionAn error which clears a call by definition has occurred in the trunk circuit signalling, e.g. reception of a charging message or signal or an acknowledgement to TUP clearing in a wrong call phase.
Detected by
Default effect on the exchangeThe call is cleared in terminal and transit exchanges. The originating exchange carries out a digit re-analysis in tree 34H.
Possibility to change the default effectUsing facility routing (command group RE, parameter CST), the terminal or transit exchanges can connect an audible tone to the incoming circuit or carry out a digit re-analysis in tree 34H. Using facility routing, the originating exchange can connect an audible tone to the subscriber.
AlarmsNo alarms.
5.174 A05H - CIRCUIT RELEASED BY CO-EXCHANGE
Text in MML printoutsCRCT RELEASED BY CO-EXCHA
DescriptionA message or signal which indicates that a circuit release has been received from the trunk circuit.
Program block
Explanation
SI5PRB SI5PRB sets the clear code when a charging message or an acknowl-edgement to clearing is received in a wrong call phase.
DN078927Issue 1-0
123
DX200 Clear Code List Clear codes
Id:0900d80580635beb
Detected by
Default effect on the exchangeThe outgoing circuit is hunted again. The signalling record indicates how many times the circuit is hunted in a call.
Possibility to change the default effectNot possible.
AlarmsNo alarms.
5.175 A07H - CALL FAILURE FROM OUTGOING CIRCUIT
Text in MML printoutsCALL FAIL FROM OUT CRCT
DescriptionA message or signal indicating a failed call attempt has been received from the outgoing circuit. The message or signal in question does not belong to the group which indicates barring. Such is e.g. reception of a CFL (call failure) message from the TUP.
Detected by-
Default effect on the exchangeThe call is cleared in terminal and transit exchanges. The originating exchange carries out a digit re-analysis in tree 32H.
Possibility to change the default effectUsing facility routing (command group RE, parameter CCF), the terminal or transit exchanges can connect an audible tone to the incoming circuit or carry out a digit re-analysis in tree 32H. Using facility routing, the originating exchange can connect an audible tone to the subscriber.
AlarmsNo alarms.
5.176 A08H - INTER-EXCHANGE SIGNALLING OUT OF ORDER
Program block
Explanation
SI5PRB SI5PRB or SI7PRB sets the clear code when it receives the message RSC (reset-circuit message).
SI7PRB –
124 DN078927Issue 1-0
DX200 Clear Code List
Id:0900d80580635beb
Clear codes
Text in MML printoutsDESTINATI POINT CONGESTI
DescriptionAfter it has received a seizure, the program block which supervises the outgoing inter-exchange signalling has found a temporary disturbance in the signalling of the hunted trunk circuit.
Detected by
Default effect on the exchangeThe call is cleared in terminal and transit exchanges. The originating exchange connects a special information tone to the subscriber. The originating exchange connects a special information tone to the subscriber or performs reanalysis in the interception tree 34H.
Possibility to change the default effectUsing facility routing (command group RE, parameter CST), the call can be directed for reanalysis in tree 34H both in terminal and transit exchanges.
AlarmsNo alarms.
5.177 A09H - ADDRESS COMPLETE MESSAGE TIME-OUT
Text in MML printoutsADDRESS COMPLETE TIME OUT
DescriptionThe ADDRESS COMPLETE message has not arrived in the originating exchange within the time supervision.
Detected by
Program block
Explanation
SI5PRB SI5PRB sets the clear code when no acknowledgement is received from the signalling within the time supervision limit.
Program block
Explanation
OC1PRB OC1PRB, OC3PRB or OUREGI sets tºhe clear code when "end-of-selec-tion" information is not received within the time supervision.
OC3PRB –
OUREGI –
DN078927Issue 1-0
125
DX200 Clear Code List Clear codes
Id:0900d80580635beb
Default effect on the exchangeThe call is cleared in terminal and transit exchanges. The originating exchange connects a congestion tone to the subscriber.
Possibility to change the default effectNot possible.
AlarmsNo alarms.
5.178 A0AH - ADDRESS COMPLETE MESSAGE SENDING TIME EXCEEDED
Text in MML printoutsADDRESS COMPLETE
DescriptionThe Common Channel Signalling (CCS) terminating exchange has not sent the "address complete" message within the time supervision.
Detected by-
Default effect on the exchangeThe call is cleared in terminal and transit exchanges. The originating exchange connects a special information tone to the subscriber.
Possibility to change the default effectNot possible.
AlarmsNo alarms.
5.179 A0CH - NO DIGITAL TRUNK
Text in MML printoutsNO DIGITAL TRUNK
DescriptionThere is no digital trunk in the desired direction.
126 DN078927Issue 1-0
DX200 Clear Code List
Id:0900d80580635beb
Clear codes
Detected by
Default effect on the exchangeThe call is cleared in terminal and transit exchanges. The originating exchange connects a special information tone to the subscriber ( call from PABX ) or performs reanalysis in the interception tree 36H ( call from subscriber ).
Possibility to change the default effectUsing facility routing (command group RE, parameter CDN), the call can be directed for reanalysis in tree 36H both in terminal and transit exchanges.
AlarmsNo alarms.
5.180 A0DH - NO ROUTE TO SPECIFIED TRANSIT OR TO DESTI-NATION
Text in MML printoutsNO ROUTE TO DESTINATION
DescriptionNo routing to a specified transit network or to the co-exchange. The called partner cannot be reached because the network through which the call has been routed does not serve the requested co-exchange, or the transit network does not exist.
Detected by-
Default effect on the exchangeThe call is cleared in terminal and transit exchanges. The originating exchange connects a special information tone to the subscriber.
Possibility to change the default effectNot possible.
AlarmsNo alarms.
5.181 A0EH - NO CIRCUIT AVAILABLE IN TRANSIT NETWORK
Program block
Explanation
INREGI INREGI sets the clear code when the digit analysis ends in congestion, and the call has requested a digital connection.
DN078927Issue 1-0
127
DX200 Clear Code List Clear codes
Id:0900d80580635beb
Text in MML printoutsNO CIRCUIT IN TRANS NW
DescriptionNo circuits available in the transit network.
Detected by
Default effect on the exchange–
Possibility to change the default effectNot possible.
AlarmsNo alarms.
5.182 A0FH - RESELECTION IN TRANSIT NETWORK APPLYING LOAD SHARING
Text in MML printoutsRESEL APPL LOAD SHARE
DescriptionReselection in the transit network applying load sharing.
Detected by
Default effect on the exchange–
Possibility to change the default effectNot possible.
AlarmsNo alarms.
Program block
Explanation
SI7PRB Detected by SI7PRB if the release message received from network is the national Belgian ISUP cause code #13.
Program block
Explanation
SI7PRB Detected by SI7PRB if the release message received from network is the national belgian ISUP cause code #14.
128 DN078927Issue 1-0
DX200 Clear Code List
Id:0900d80580635beb
Clear codes
5.183 B02H - TRANSIT/TERMINAL SIGNAL WAIT TIME SUPER-VISION EXCEEDED
Text in MML printoutsTRANS/TERM SIGN WAIT EXC
DescriptionNo READY FOR DIALLING signal is received in time from the outgoing Y-code circuit.
Detected by
Default effect on the exchangeThe call is cleared in the terminal and transit exchanges. The originating exchange connects a special information tone to the subscriber.
Possibility to change the default effectNot possible.
AlarmsNo alarms.
5.184 B0FH - LENGTH OF CHANGED CALLED SUBSCRIBER NUMBER EXCEEDED
Text in MML printoutsLENGTH OF CHANGED B NUM
DescriptionThe new called number (B-subscriber number) obtained from the trunk circuit in con-junction with the number modification is too long.
Detected by-
Default effect on the exchangeThe call is cleared in terminal and transit exchanges. The originating exchange connects a special information tone to the subscriber.
Possibility to change the default effectNot possible.
Program block
Explanation
OUREGI OUREGI sets the clear code when CASSIG sends message long_char_s (0081).
DN078927Issue 1-0
129
DX200 Clear Code List Clear codes
Id:0900d80580635beb
AlarmsNo alarms.
5.185 B11H - MODEM COMMUNICATION ERROR
Text in MML printoutsMODEM COMMUNICATION ERROR
DescriptionInternal error has occured in DSP (Digital Signal Processing) software.
Detected by
Default effect on the exchangeThe exhange clears the call. Special tone is connected.
Possibility to change the default effectNot possible.
AlarmsNo alarms.
5.186 B17H - ADDRESS INCOMPLETE
Text in MML printoutsADDRESS INCOMPLETE
DescriptionInsufficient amount of digits or insufficient dialling information has been received.
Detected by-
Default effect on the exchangeThe call is cleared in terminal and transit exchanges. The originating exchange carries out a digit re-analysis in tree 2CH (command group RE, parameter CDP).
Program block
Explanation
MGAPRB MGAPRB sets the clear code according to obtained error type from MRMPRB.
SI5PRB –
130 DN078927Issue 1-0
DX200 Clear Code List
Id:0900d80580635beb
Clear codes
Possibility to change the default effectUsing facility routing, the transit and terminal exchanges can connect an audible tone to the subscriber or carry out a digit re-analysis in tree 2CH. Using facility routing, the orig-inating exchange can connect an audible tone to the subscriber.
AlarmsNo alarms.
5.187 B18H - SERVICE UNAVAILABLE
Text in MML printoutsSERVICE UNAVAILABLE
DescriptionISDN data call cannot be connected because the terminating node is not equipped to handle ISDN digital calls.
Detected by-
Default effect on the exchangeThe call is cleared in terminal and transit exchanges. The originating exchange carries out a digit re-analysis in tree 32H (command group RE, parameter CCF).
Possibility to change the default effectNot possible.
AlarmsNo alarms.
5.188 B19H - SERVICE INCOMPATIBLE
Text in MML printoutsSERVICE INCOMPATIBLE
DescriptionThe network terminating equipment (NTE) is not equipped with the requested ISDN data service.
Detected by-
Default effect on the exchangeThe call is cleared in terminal and transit exchanges. The originating exchange connects a special information tone to the subscriber.
DN078927Issue 1-0
131
DX200 Clear Code List Clear codes
Id:0900d80580635beb
Possibility to change the default effectNot possible.
AlarmsNo alarms.
5.189 B20H - NETWORK ADDRESS EXTENSION (NAE) ERROR
Text in MML printoutsNAE ERROR
DescriptionThe ISDN PABX has received insufficient or incorrect NAE (Network Address Exten-sion) information.
Detected by-
Default effect on the exchangeThe call is cleared in terminal and transit exchanges. The originating exchange connects a special information tone to the subscriber.
Possibility to change the default effectNot possible.
AlarmsNo alarms.
5.190 B21H - DTE IS UNCONTROLLED
Text in MML printoutsDTE UNCONTROLLED
DescriptionThe Data Terminal Equipment (DTE) is uncontrolled in ISDN calls.
Detected by-
Default effect on the exchangeThe call is cleared in terminal and transit exchanges. The originating exchange connects a special information tone to the subscriber.
Possibility to change the default effectNot possible.
132 DN078927Issue 1-0
DX200 Clear Code List
Id:0900d80580635beb
Clear codes
AlarmsNo alarms.
5.191 B23H - DUAL SEIZURE FROM BIDIRECTIONAL CIRCUIT
Text in MML printoutsDUAL SEIZURE BOTH WAY CIR
DescriptionA seizure has been detected from a bidirectional circuit after the circuit has been seized in an outgoing direction. The latter seizure is accepted, and a search for a new outgoing circuit is started for the former seizure.
Detected by-
Default effect on the exchangeThe outgoing circuit is hunted again. The number of hunting attempts is indicated in the outgoing signalling record.
Possibility to change the default effectNot possible.
AlarmsNo alarms.
5.192 B2AH - BLOCKING RECEIVED
Text in MML printoutsBLOCKING RECEIVED
DescriptionBlocking received from a bidirectional or outgoing circuit in reply to an initial address message.
Detected by
Default effect on the exchangeThe outgoing circuit is hunted again. The number of hunting attempts is indicated in the outgoing signalling record.
Program block
Explanation
SI5PRB SI7PRB or SI5PRB sets the clear code when the BLO messages (BLOCKING) is received from the signalling.
SI7PRB –
DN078927Issue 1-0
133
DX200 Clear Code List Clear codes
Id:0900d80580635beb
Possibility to change the default effectNot possible.
AlarmsNo alarms.
5.193 B2BH - PARAMETER DOES NOT EXIST OR IS NOT IMPLE-MENTED
Text in MML printoutsPARAM NO EX OR IMPL
DescriptionA message which contains illegal parameters has been received from an Intelligent Network (IN) application.
Detected by
Default effect on the exchangeThe call is cleared in terminal and transit exchanges. The originating exchange connects a special information tone to the subscriber.
Possibility to change the default effectNot possible.
AlarmsNo alarms.
5.194 B2CH - INTELLIGENT NETWORK APPLICATION PROTOCOL ERROR
Text in MML printoutsIN PROTOCOL ERROR
DescriptionA message has been received from an Intelligent Network (IN) application in a state where no message should have arrived.
Program block
Explanation
ICXPRB ICxPRB (inif_t) sets the clear code when a message with incorrect data is received from an IN application.
134 DN078927Issue 1-0
DX200 Clear Code List
Id:0900d80580635beb
Clear codes
Detected by
Default effect on the exchangeThe call is cleared in terminal and transit exchanges. The originating exchange connects a special information tone to the subscriber.
Possibility to change the default effectNot possible.
AlarmsNo alarms.
5.195 B2DH - INTELLIGENT NETWORK APPLICATION RESPONSE TIME-OUT
Text in MML printoutsIN RESPONSE TIME OUT
DescriptionAn Intelligent Network (IN) application does not respond to an event requiring acknowl-edgement within a time limit.
Detected by
Default effect on the exchangeThe call is cleared in terminal and transit exchanges. The originating exchange connects a special information tone to the subscriber.
Possibility to change the default effectNot possible.
AlarmsNo alarms.
Program block
Explanation
ICXPRB ICxPRB (inif_t) sets the clear code when an error is detected in the IN pro-tocol.
Program block
Explanation
ICXPRB ICxPRB (inif_t) sets the clear code when the IN does not respond within the time supervision.
DN078927Issue 1-0
135
DX200 Clear Code List Clear codes
Id:0900d80580635beb
5.196 B2EH - MAXIMUM NUMBER OF TRIGGERING EVENTS IN A CALL HAS BEEN REACHED
Text in MML printoutsIN TRIG COUNT LIMIT
DescriptionThe maximum number of Intelligent Network (IN) triggering events in a call has been reached.
Detected by
Default effect on the exchangeThe call is cleared in terminal and transit exchanges. The originating exchange connects a special information tone to the subscriber.
Possibility to change the default effectNot possible.
AlarmsNo alarms.
5.197 B2FH - TCAP ERROR
Text in MML printoutsTCAP ERROR
DescriptionAn error occurred in the connection to the service control point (SCP) provided by the transaction capabilities application part (TCAP).
Detected by
Default effect on the exchangeThe call is cleared in terminal and transit exchanges. The originating exchange connects a special information tone to the subscriber.
Program block
Explanation
ICXPRB ICxPRB (inif_t) sets the clear code when the call has reached the maximum number of IN triggering events.
Program block
Explanation
INXPRB INXPRB sets the clear code when an error has been detected in the TCAP connection.
136 DN078927Issue 1-0
DX200 Clear Code List
Id:0900d80580635beb
Clear codes
Possibility to change the default effectNot possible.
AlarmsNo alarms.
5.198 B30H - ASN1 CODING OR DECODING ERROR
Text in MML printoutsASN1 CODING DECODING ERRO
DescriptionAn ASN.1 coding or decoding error has been detected.
Detected by
Default effect on the exchangeThe call is cleared in terminal and transit exchanges. The originating exchange connects a special information tone to the subscriber.
Possibility to change the default effectNot possible.
AlarmsNo alarms.
5.199 B31H - SELECTIVE CALL CONGESTION HAS PREVENTED CALL ATTEMPT
Text in MML printoutsCALL IS GAPPED
DescriptionThe call attempt has been interrupted by restricting the amount of calls on the basis of the selected number.
Detected by-
Default effect on the exchangeThe call is cleared in terminal and transit exchanges. The originating exchange connects a special information tone to the subscriber.
Program block
Explanation
INXPRB INXPRB sets the clear code when ASN.1 coding failed.
DN078927Issue 1-0
137
DX200 Clear Code List Clear codes
Id:0900d80580635beb
Possibility to change the default effectNot possible.
AlarmsNo alarms.
5.200 B32H - CALL RELEASE ORDERED BY INTELLIGENT NETWORK APPLICATION
Text in MML printoutsIN DISCONNECT BY SCP
DescriptionAn Intelligent Network (IN) application in the SCP (Service Control Point) or inside the exchange has ordered the release of the call.
Detected by
Default effect on the exchangeThe call is cleared in terminal and transit exchanges. The originating exchange connects a special information tone to the subscriber.
Possibility to change the default effectNot possible.
AlarmsNo alarms.
5.201 B33H - CONTINUITY CHECK FAILURE
Text in MML printoutsCONTINUITY CHECK FAILURE
DescriptionContinuity check of the speech path has failed.
Detected by
Program block
Explanation
IDXSCP –
Program block
Explanation
SI5PRB SI5PRB or SI7PRB sets the clear code when the continuity check of the speech path fails.
138 DN078927Issue 1-0
DX200 Clear Code List
Id:0900d80580635beb
Clear codes
Default effect on the exchangeThe outgoing circuit is hunted again. The amount of hunting attempts is indicated in the outgoing signalling record.
Possibility to change the default effectNot possible.
AlarmsNo alarms.
5.202 B34H - A-NUMBER IS NOT THE REGISTERED NUMBER OF AN INDIRECT SUBSCRIBER
Text in MML printoutsNOT INDIRECT SUBSCRIBER
DescriptionCall attempt from a number not registered as an indirect subscriber of the exchange.
Detected by
Default effect on the exchangeThe call is cleared in terminal and transit exchanges. The originating exchange connects a special information tone to the subscriber.
Possibility to change the default effectNot possible.
AlarmsNo alarms.
5.203 B35H - TOO MANY FRAUDULENT ATTEMPTS TO USE CALLING CARD
Text in MML printoutsCC NUMBER FRAUD
SI7PRB –
Program block
Explanation
Program block
Explanation
IDXSCP –
DN078927Issue 1-0
139
DX200 Clear Code List Clear codes
Id:0900d80580635beb
DescriptionThere have been too many fraudulent attempts to use a calling card. Therefore its use is temporarily prevented.
Detected by
Default effect on the exchangeThe call is cleared in terminal and transit exchanges. The originating exchange connects a special information tone to the subscriber.
Possibility to change the default effectNot possible.
AlarmsNo alarms.
5.204 B36H - CALLING CARD NUMBER SELECTED BY USER NOT FOUND
Text in MML printoutsCC NUMBER NOT FOUND
DescriptionThe number of the calling card with keyword dialled by the user is not found.
Detected by
Default effect on the exchangeThe call is cleared in terminal and transit exchanges. The originating exchange connects a special information tone to the subscriber.
Possibility to change the default effectNot possible.
AlarmsNo alarms.
Program block
Explanation
IDXSCP –
Program block
Explanation
IDXSCP –
140 DN078927Issue 1-0
DX200 Clear Code List
Id:0900d80580635beb
Clear codes
5.205 B37H - IN-SERVICE INTERRUPTED FOR SUSPECTED FRAUD
Text in MML printoutsSUSPECTED FRAUD
DescriptionThe Intelligent Network (IN) service has been interrupted for suspected fraud.
Detected by
Default effect on the exchangeThe call is cleared in terminal and transit exchanges. The originating exchange connects a special information tone to the subscriber.
Possibility to change the default effectNot possible.
AlarmsNo alarms.
5.206 B38H - IN FALLBACK CODE ONE
Text in MML printoutsIN FALLBACK CODE ONE
DescriptionAn IN session is started in the Outgoing Call Control (OCxPRB). The service control point (SCP) gives a RELEASE_CALL message to the service switching point (SSP). The ISUP cause code is mapped to the IN FALLBACK CODE ONE clear code and passed to the Incoming Call Control. An IN trigger detection point (4) is found. If a PRFILE parameter ("IN_FALLBACK_SSET_INDEX") is defined, an IN session is started. Otherwise the call is cleared.
Detected by
Default effect on the exchangeThe Incoming Call Control detects an IN trigger detection point.
Program block
Explanation
IDXSCP –
Program block
Explanation
INXPRB The INXPRB; signalling program handling CoreInap protocol.
DN078927Issue 1-0
141
DX200 Clear Code List Clear codes
Id:0900d80580635beb
Possibility to change the default effectThe PRFILE parameter IN_FALLBACK_SSET_INDEX controls the action. Any value different from 0 starts a new IN session. Otherwise the call is cleared.
AlarmsNo alarms.
5.207 B39H - IN FALLBACK CODE TWO
Text in MML printoutsIN FALLBACK CODE TWO
DescriptionAn IN session is started in Outgoing Call Control (OCxPRB). The service control point (SCP) gives a RELEASE_CALL message to the service switching point (SSP). The ISUP cause code is mapped to IN FALLBACK CODE TWO clear code and passed to Incoming Call Control. An IN trigger detection point (4) is found. If a PRFILE parameter ("IN_FALLBACK_SSET_INDEX") is defined, an IN session is started. Otherwise the call is cleared.
Detected by
Default effect on the exchangeThe Incoming Call Control detects an IN trigger detection point.
Possibility to change the default effectThe PRFILE parameter IN_FALLBACK_SSET_INDEX controls the action. Any value different from 0 starts a new IN session. Otherwise the call is cleared.
AlarmsNo alarms.
5.208 B3AH - IN FALLBACK CODE THREE
Text in MML printoutsIN FALLBACK CODE THREE
DescriptionAn IN session is started in Outgoing Call Control (OCxPRB). The service control point (SCP) gives a RELEASE_CALL message to the service switching point (SSP). The ISUP cause code is mapped to IN FALLBACK CODE THREE clear code and passed to Incoming Call Control. An IN trigger detection point (4) is found. If a PRFILE parameter
Program block
Explanation
INXPRB The INXPRB; signalling program handling CoreInap protocol.
142 DN078927Issue 1-0
DX200 Clear Code List
Id:0900d80580635beb
Clear codes
("IN_FALLBACK_SSET_INDEX") is defined an IN session is started. Otherwise the call is cleared.
Detected by
Default effect on the exchangeIncoming Call Control is detecting an IN trigger detection Point.
Possibility to change the default effectThe PRFILE parameter IN_FALLBACK_SSET_INDEX is controlling the action. A value different from 0 gives start to a new IN session. Otherwise the call is cleared.
AlarmsNo alarms.
5.209 B3BH - IN FALLBACK CODE FIVE
Text in MML printoutsIN FALLBACK CODE FIVE
DescriptionAn IN session is started in Outgoing Call Control (OCxPRB). The service control point (SCP) gives a RELEASE_CALL message to the service switching point (SSP). The ISUP cause code is mapped to IN FALLBACK CODE FIVE clear code and passed to Incoming Call Control. An IN trigger detection point (4) is found. If a PRFILE parameter ("IN_FALLBACK_SSET_INDEX") is defined an IN session is started. Otherwise the call is cleared.
Detected by
Default effect on the exchangeIncoming Call Control is detecting an IN trigger detection Point.
Possibility to change the default effectThe PRFILE parameter IN_FALLBACK_SSET_INDEX is controlling the action. A value different from 0 gives start to a new IN session. Otherwise the call is cleared.
AlarmsNo alarms.
Program block
Explanation
INXPRB The INXPRB ; signalling program handling CoreInap protocol.
Program block
Explanation
INXPRB The INXPRB; signalling program handling CoreInap protocol.
DN078927Issue 1-0
143
DX200 Clear Code List Clear codes
Id:0900d80580635beb
5.210 B3CH - IN FALLBACK CODE FOUR
Text in MML printoutsIN FALLBACK CODE FOUR
DescriptionAn IN session is started in Outgoing Call Control (OCxPRB). The service control point (SCP) gives a RELEASE_CALL message to the service switching point (SSP). The ISUP cause code is mapped to IN FALLBACK CODE FOUR clear code and passed to Incoming Call Control. An IN trigger detection point (4) is found. If a PRFILE parameter ("IN_FALLBACK_SSET_INDEX") is defined an IN session is started. Otherwise the call is cleared.
Detected by
Default effect on the exchangeIncoming Call Control is detecting an IN trigger detection Point.
Possibility to change the default effectThe PRFILE parameter IN_FALLBACK_SSET_INDEX is controlling the action. A value different from 0 gives start to a new IN session. Otherwise the call is cleared.
AlarmsNo alarms.
5.211 B3DH - IN DIALOG - ROUTING FAILURE IN SS7 NETWORK
Text in MML printoutsIN SS7 ROUTING FAILURE
DescriptionThe Common Channel Signalling system has returned TCAP message attached to IN ( Intelligent Network ) dialog because of a routing problem. The TCPROG(=TCAP) returns the error code to the INXPRB with the tc2_notice_s message, which gives the reason to the IN service failure. The alarm given specifies the error code precisely.
Detected by
Program block
Explanation
INXPRB The INXPRB ; signalling program handling CoreInap protocol.
Program block
Explanation
INXPRB The INXPRB sends this clear code to the call control.
144 DN078927Issue 1-0
DX200 Clear Code List
Id:0900d80580635beb
Clear codes
Default effect on the exchangeThe call is cleared in terminal and transit exchanges. The originating exchange carries out a digit re-analysis in interception tree 34H or connects an audible tone.
Possibility to change the default effectBy using facility routing, terminal and transit exchanges can carry out a digit re-analysis in interception tree or connect an audible tone. Interception tree 34H (command group RE, parameter CST).
Alarms2617
5.212 C00H - DIAL WAIT TIME EXCEEDED
Text in MML printoutsDIAL WAIT TIME EXCEEDED
DescriptionThe dialling has not been received from the incoming circuit within the time supervision.
Detected by
Default effect on the exchangeThe call is cleared in terminal and transit exchanges. The originating exchange connects a congestion tone to the subscriber or performs reanalysis in the interception tree 2CH.
Possibility to change the default effectNot possible.
AlarmsNo alarms.
5.213 C01H - PROHIBITED DIALLING
Text in MML printoutsPROHIBITED DIALLING
DescriptionA digit sequence not known to the digit analysis files has been received.
Program block
Explanation
ICXPRB ICxPRB or INREGI sets the clear code when the outgoing connection has not yetº been started, and the time supervision limit set for waiting for the dialling has been exceeded.
INREGI –
DN078927Issue 1-0
145
DX200 Clear Code List Clear codes
Id:0900d80580635beb
Detected by
Default effect on the exchangeThe call is cleared in terminal and transit exchanges. The originating exchange carries out a digit re-analysis in interception tree.
Possibility to change the default effectUsing facility routing transit and terminal exchanges can connect an audible tone to the subscriber or carry out a digit re-analysis in interception tree 2CH (command group RE, parameter CDP). Using facility routing, the originating exchange can connect an audible tone to the subscriber.
AlarmsNo alarms.
5.214 C02H - INSUFFICIENT DIALLING FROM SUBSCRIBER SIGNALLING
Text in MML printoutsINSUFFICIENT DIALLING
DescriptionAn insufficient amount of digits has been received from the subscriber for number anal-ysis.
Detected by
Default effect on the exchangeThe call is cleared in terminal and transit exchanges. The originating exchange carries out a digit re-analysis in tree 2CH (command group RE, parameter CDP).
Possibility to change the default effectUsing facility routing, the transit and terminal exchanges can connect an audible tone to the subscriber or carry out a digit re-analysis in tree 2CH. Using facility routing, the orig-inating exchange can connect an audible tone to the subscriber.
Program block
Explanation
ICXPRB ICxPRB or INREGI sets the clear code when digit analysis has resulted in congestion.
INREGI ICxPRB or INREGI sets the clear code when digit analysis has resulted in congestion.
Program block
Explanation
ICXPRB ICxPRB sets the clear code because the number does not contain enough digits for the charging attribute analysis (option), the routing attribute analysis (option) or the digit analysis.
146 DN078927Issue 1-0
DX200 Clear Code List
Id:0900d80580635beb
Clear codes
AlarmsNo alarms.
5.215 C04H - CALLING SUBSCRIBER HAS DIALLED WRONG KEYWORD
Text in MML printoutsA HAS DIALLED WRONG KEYW
DescriptionIn a facility control call (activation/inactivation), the calling subscriber (A-subscriber) has dialled a keyword which is different from the one stored in the memory of the exchange (additional subscriber data record).
Detected by-
Default effect on the exchangeThe call is cleared in terminal and transit exchanges. The originating exchange connects a special information tone to the subscriber or performs reanalysis in the interception tree 2CH.
Possibility to change the default effectUsing facility routing (command group RE, parameter CDP), the call can be directed for reanalysis in tree 2CH both in terminal and transit exchanges.
AlarmsNo alarms.
5.216 C05H - CALLING SUBSCRIBER HAS NO RIGHT TO FACILITY
Text in MML printoutsA HAS NO RIGHT TO MODIFY
DescriptionThe calling subscriber (A-subscriber) has no right to modify a facility from his own line.
Detected by
Program block
Explanation
OUREGI OUREGI (ARF) sets the clear code when the subscriber gives an incorrect password in conjunction with a facility procedure.
DN078927Issue 1-0
147
DX200 Clear Code List Clear codes
Id:0900d80580635beb
Default effect on the exchangeThe call is cleared in terminal and transit exchanges. The originating exchange connects a special information tone to the subscriber.
Possibility to change the default effectNot possible.
AlarmsNo alarms.
5.217 C06H - CALLING SUBSCRIBER HAS NO RIGHT TO STORE NUMBER
Text in MML printoutsA HAS NO RIGHT TO STORE
DescriptionThe calling subscriber (A-subscriber) has performed a facility procedure which stores the called number (B-subscriber) or the third number (C-subscriber). However, the sub-scriber has no right to store this number (subscriber's outgoing calls are restricted, or absent subscriber service is prohibited to this direction). A-subscriber tries to activate CFNR with subscriber controlled time supervision and given time value is out of allowed values.
Detected by
Default effect on the exchangeThe call is cleared in terminal and transit exchanges. The originating exchange connects a special information tone to the subscriber.
Possibility to change the default effectNot possible.
AlarmsNo alarms.
5.218 C08H - PREMATURE DIALLING
Program block
Explanation
FCCPRB OUREGI (ARF) and FCCPRB sets the clear code when the activation of the facility is prevented because of restriction of outgoing calls. FCCPRB also sets this clear code when subscriber controlled time supervision is out of allowed values.
OUREGI –
148 DN078927Issue 1-0
DX200 Clear Code List
Id:0900d80580635beb
Clear codes
Text in MML printoutsPREMATURE DIALLING
DescriptionThe subscriber has dialled during a register wait state, i.e. before hearing the dial tone, or there are disturbances on the subscriber line. The call set-up is interrupted.
Detected by-
Default effect on the exchangeThe call is cleared in terminal and transit exchanges. The originating exchange connects a special information tone to the subscriber.
Possibility to change the default effectNot possible.
AlarmsNo alarms.
5.219 C09H - SERVICE OR FACILITY ACTIVATION RESTRICTED
Text in MML printoutsSERV/FACIL ACTIVA RESTR
DescriptionThe subscriber has tried to activate a service or a facility which is contradictory to other active services, facilities or the subscriber category. It is also possible that a mobile station has requested a bearer capability which is implemented but which the mobile station is not authorized to use. Activation is prevented also during the trial configuration. The FCCPRB sets this clear code when the subscriber tries to activate a facility which is already activated. The double activation is restricted by an exhange dependent parameter.
Detected by-
Default effect on the exchangeThe call is cleared in terminal and transit exchanges. The originating exchange connects a special information tone to the subscriber.
Possibility to change the default effectUsing facility routing (command group RE, parameter CDN), the call can be directed for reanalysis in tree 36H both in terminal and transit exchanges.
AlarmsNo alarms.
DN078927Issue 1-0
149
DX200 Clear Code List Clear codes
Id:0900d80580635beb
5.220 C0AH - SERVICE OR FACILITY USAGE RESTRICTED
Text in MML printoutsSERV/FACIL USAGE RESTR
DescriptionThe subscriber has requested a service or a facility which is contradictory to other active services, facilities or the subscriber category. Another reason is a temporary facility resource congestion in the exchange. In the case of a mobile station, it has requested a bearer capability which is implemented by the equipment which generated this clear code but which is not available at this time.
Detected by-
Default effect on the exchangeThe call is cleared in terminal and transit exchanges. The originating exchange carries out a digit re-analysis in tree 32H.
Possibility to change the default effectUsing facility routing (command group RE, parameter CCF), transit and terminal exchanges can connect an audible tone to the subscriber or carry out a digit re-analysis in tree 32H. Using facility routing, the originating exchange can connect an audible tone to the subscriber.
AlarmsNo alarms.
5.221 C0BH - INCONSISTENCY BETWEEN A- AND B-SUB-SCRIBERS
Text in MML printoutsINCONSISTENT BETW A AND B
DescriptionThe call set-up failed because of inconsistency between the data on the calling sub-scriber (A-subscriber) and the called subscriber (B-subscriber). For example, a digital subscriber has requested a digital path, but the B-subscriber has been found analog.
Detected by-
Default effect on the exchangeIn the originating exchange a digit reanalysis is performed in tree 35H. The call is cleared in terminal and transit exchanges. The originating exchange connects a special information tone to the subscriber ( call from PABX ) or performs reanalysis in the inter-ception tree 32H ( call from subscriber ).
150 DN078927Issue 1-0
DX200 Clear Code List
Id:0900d80580635beb
Clear codes
Possibility to change the default effectUsing facility routing the call can be directed for reanalysis in interception tree both in terminal and transit exchanges. In the originating exchange an audible tone can be con-nected to the subscriber using facility routing. Interception tree 35H (command group RE, parameter CAB). Interception tree 32H (command group RE, parameter CCF).
AlarmsNo alarms.
5.222 C0DH - BEARER CAPABILITY NOT PRESENTLY AVAIL-ABLE
Text in MML printoutsBEARER CAPA NOT AVAILABLE
DescriptionAmobile station has requested a bearer capability which is implemented by the equip-ment which generated this cause but which is not available at this time.
Detected by
Default effect on the exchange–
Possibility to change the default effectNot possible.
AlarmsNo alarms.
5.223 D00H - SUBSCRIBER SIGNALLING MESSAGE CONTENT ERROR
Text in MML printoutsSUBS SIGN MESS CONT ERR
DescriptionThere has been an inconsistent or invalid message in the communication between the base station and the mobile station or between the subscriber module and the sub-
Program block
Explanation
AIFPRB AIFPRB set this clear code because the mobile station has requested a bearer capability which is implemented by the equipment which gener-ated this cause but which is not available at this time.
DN078927Issue 1-0
151
DX200 Clear Code List Clear codes
Id:0900d80580635beb
scriber terminal. This clear code is used also when encountering an illogical or errone-ous subscriber signalling message.
Detected by
Default effect on the exchangeThe call is cleared in terminal and transit exchanges. The originating exchange connects a special information tone to the subscriber.
Possibility to change the default effectNot possible.
AlarmsNo alarms.
5.224 D01H - SUBSCRIBER SIGNALLING MESSAGE FORMAT ERROR
Text in MML printoutsSUBS SIGN MESS FORM ERR
DescriptionThere has been a format error in the message between the base station and the mobile station or between the subscriber module and the subscriber terminal, e.g a mandatory or an optional information element is missing.
Detected by-
Default effect on the exchangeThe call is cleared in terminal and transit exchanges. The originating exchange connects a special information tone to the subscriber.
Possibility to change the default effectNot possible.
AlarmsNo alarms.
5.225 D03H - SERVICE OR FUNCTION NOT IMPLEMENTED
Program block
Explanation
SI6PRB SI6PRB sets the clear code when unknown values are received in network messages.
152 DN078927Issue 1-0
DX200 Clear Code List
Id:0900d80580635beb
Clear codes
Text in MML printoutsSERV OR FUNC NOT IMPLEM
DescriptionA service or a function requested by the subscriber has not been implemented in the exchange.
Detected by-
Default effect on the exchangeThe call is cleared in terminal and transit exchanges. The originating exchange carries out a digit re-analysis in tree 36H (command group RE, parameter CDN).
Possibility to change the default effectNot possible.
AlarmsNo alarms.
5.226 D04H - SUBSCRIBER SIGNALLING PROTOCOL ERROR
Text in MML printoutsSUBS SIGN PROTOCOL ERROR
DescriptionThe signalling messages have arrived in incorrect order with respect to the call phase. This protocol error has been registered in the communication between the base station and the mobile station or between the subscriber module and the subscriber terminal. This clear code is also used in PABX signalling protocol errors.
Detected by-
Default effect on the exchangeThe call is cleared in terminal and transit exchanges. The originating exchange carries out a digit re-analysis in tree 34H.
Possibility to change the default effectUsing facility routing (command group RE, parameter CST), terminal and transit exchanges can carry out a digit re-analysis in tree 34H. Using facility routing, the origi-nating exchange can connect an audible tone to the subscriber.
AlarmsNo alarms.
5.227 D06H - AOCC CHARGING ERROR
DN078927Issue 1-0
153
DX200 Clear Code List Clear codes
Id:0900d80580635beb
Text in MML printoutsAOCC CHARGING ERROR
DescriptionThe call has been cleared because the mobile station which has been equipped with AOC-C (Advice of Charge, Charging) supplementary service does not acknowledge the Charge Advice Information (CAI).
Detected by-
Default effect on the exchangeThe call is cleared in terminal and transit exchanges. The originating exchange connects a special information tone to the subscriber.
Possibility to change the default effectNot possible.
AlarmsNo alarms.
5.228 D07H - NO RESPONSE TO CALL ESTABLISHMENT: ALERTING OR CONNECT
Text in MML printoutsNO USER RESPONDING
DescriptionThe user device has not responded to a call establishment message with either ALERTING or CONNECT message within the time supervision. Call Forwarding Uncon-ditional (CFU) is prevented by this clear code if the amount of call forwarding steps has been exceeded.
Detected by
Default effect on the exchangeThe call is cleared in transit and terminal exchanges. The originating exchange connects a busy tone to the subscriber.
Program block
Explanation
SI1PRB SI1PRB sets the clear code when a PABX does not answer within the time supervision. SI6PRB sets the clear code when a terminal equipment does not answer within the time supervision.
SI6PRB –
154 DN078927Issue 1-0
DX200 Clear Code List
Id:0900d80580635beb
Clear codes
Possibility to change the default effectUsing facility routing (command group RE, parameter CCF), the call can be directed for reanalysis in tree 32H both in terminal and transit exchanges. Interception tree 33H (command group RE, parameter CBB).
AlarmsNo alarms.
5.229 D08H - GSM ERH 4.08 PROTOCOL TIMER EXPIRES
Text in MML printoutsGSM ERH408 TIME OUT
DescriptionThe procedure has started upon the expiry of a timer in agreement with GSM Recom-mendation 04.08.
Detected by-
Default effect on the exchangeThe call is cleared in transit and terminal exchanges. The originating exchange connects an a udible tone to the subscriber.
Possibility to change the default effectNot possible.
AlarmsNo alarms.
5.230 D0BH - DUAL LOG-IN
Text in MML printoutsDUAL LOG-IN
DescriptionDual log-in to an operator position.
Detected by-
Default effect on the exchangeThe call is cleared in transit and terminal exchanges. The originating exchange connects a special information tone to the subscriber.
Possibility to change the default effectNot possible.
DN078927Issue 1-0
155
DX200 Clear Code List Clear codes
Id:0900d80580635beb
AlarmsNo alarms.
5.231 D0FH - ISDN-SUBSCRIBER FACILITY DIALLING REJECTED
Text in MML printoutsFACILITY REJECTED
DescriptionISDN-subscriber has dialled wrong facility procedure in activation, deactivation or use of facility. (for example, the service code is wrong, square character in the middle of facility procedure.)
Detected by
Default effect on the exchangeCall is disconnected with tone or announcement.
Possibility to change the default effectNot possible.
AlarmsNo alarms.
5.232 D10H - MANDATORY INFORMATION ELEMENT MISSING
Text in MML printoutsMANDATORY IE MISSING
DescriptionA mandatory information element was missing in a message, for example Bearer Capa-bility in a SETUP message.
Detected by
Program block
Explanation
FCCPRB IC6PRB, FCCPRB
IC6PRB –
Program block
Explanation
SI1PRB Detected by SI1PRB when a SETUP message does not contain a manda-tory information element, for example Bearer Capability.
156 DN078927Issue 1-0
DX200 Clear Code List
Id:0900d80580635beb
Clear codes
Default effect on the exchangeThe message (SETUP) is not accepted and the call is cleared.
Possibility to change the default effectNot possible.
AlarmsNo alarms.
5.233 D11H - INVALID INFORMATION ELEMENT CONTENT
Text in MML printoutsINVALID IE CONTENT
DescriptionInformation element contents in a message are invalid, for example Bearer Capability in a SETUP message.
Detected by
Default effect on the exchangeA call from an access is not accepted.
Possibility to change the default effectNot possible.
AlarmsNo alarms.
Program block
Explanation
SI1PRB Detected by SI1PRB when a SETUP message contains an invalid man-datory information element, for example Bearer Capability.
DN078927Issue 1-0
157
DX200 Clear Code List Clear code index
Id:0900d80580635beb
6 Clear code index
NUMBER NAME
0000H NORMAL END OF CALL
0001H SUSPENDED CALL
0003H CALL DURATION BELOW SUPERVISION TIME
0004H B BUSY OR CONGESTION RECEIVED FROM OUTGOING CIRCUIT
0005H CALLED SUBSCRIBER BUSY
0006H TIME-OUT FOR B-SUBSCRIBER ANSWER
0007H CALL WAITING TIME-OUT
0008H CALLED SUBSCRIBER NOT CONNECTED
0009H CALL ALREADY WAITING
000AH INTERVENTION ALREADY ON
000BH REROUTING DUE TO B-SUBSCRIBER FACILITY
000CH OUTGOING DIRECTION RESTRICTED DUE TO CRISIS MODE
000EH MALICIOUS CALL TRACING
000FH INTERMEDIATE CHARGING
0010H ABSENT SUBSCRIBER
0011H OPERATOR PRIORITY ACCESS
0012H NO PAGING RESPONSE
0013H CALL TRANSFER RECALL DUE TO C-SUBSCRIBER ANSWER TIME-OUT
0015H NORMAL UNSPECIFIED
0016H SUBSCRIBER'S CHARGING CAPACITY EXCEEDED IN THE EXCHANGE
0018H INTERMEDIATE CHARGING IN THE END OF THE PHASE CHARGING
0020H ANNOUNCEMENT SUCCESS IN INTERCEPTION
0025H CALL DROP BACK RELEASE
0031H NOT ENOUGH CREDIT TO CALL
0100H CIRCUIT RE-SEIZED
0101H CIRCUIT RELEASED BEFORE 'END OF THE CALL' NOTICE
0102H CALL RECORD RELEASED DURING CALIBRATION
0103H CHARGING IN WRONG PHASE OF CALL
0201H CALL RELEASED
0202H CLEAR REQUEST RECEIVED FROM OUTGOING CIRCUIT
0203H B-CHANNEL UNACCEPTABLE
0204H ESTABLISHED B-CHANNEL
0206H CALL REJECTED
0207H SUBSCRIBER CONGESTION
020BH CLEAR IN DETAILED CHARGING
020EH CALLING SUBSCRIBER LINE VACANT OR OUT OF SERVICE
158 DN078927Issue 1-0
DX200 Clear Code List
Id:0900d80580635beb
Clear code index
020FH CHANGE OF OUTGOING CIRCUIT
0210H NULL NUP
0211H NETWORK, REJECTED DIVERTED CALLS
0213H NETWORK, USER NOT IN CUG
0215H CALL DROP BACK
0216H MISDIALLED TRUNK PREFIX
0217H TEMPORARY OUT OF ORDER
0218H OUT OF CATCHMENT AREA
0219H TRANSLATION OUT-OF-SERVICE
0220H ANONYMOUS CALLS REJECTION
0252H UNTERMINATED CALL TO A PORTED NUMBER
0300H CALLING SUBSCRIBER BARRED DUE TO RESTRICTION IN THE OUTGOING DIREC-TION
0301H CALLING SUBSCRIBER'S OUTGOING CALL RESTRICTED BY OPERATOR
0304H CALLED SUBSCRIBER LINE OUT OF SERVICE
0305H CALLED SUBSCRIBER LINE FAULTY
0306H ACCESS TO B-SUBSCRIBER LINE RESTRICTED
0307H B-NUMBER UNUSED
0308H B-NUMBER CHANGED
0309H TIME-OUT WHEN WAITING FOR OPERATOR'S INTERVENTION
030AH CLEAR/CALLING SUBSCRIBER HAS MADE ONHOOK DURING SET-UP PHASE
030BH CLEAR/CALLING SUBSCRIBER HAS MADE ONHOOK WHEN WAITING FOR ANSWER
030CH REANSWER TIME OUT
030DH B- OR C-NUMBER IS NOT REGISTERED
030EH CALLED SUBSCRIBER LINE BLOCKED
030FH CHANGE IN NUMBERING PLAN
0310H CLOSED USER GROUP RESCTRICTION
0311H BEARER SERVICE NOT PROVIDED
0312H TELESERVICE NOT PROVIDED
0315H CALLED SUBSCRIBER HAS CALL DIVERSION BARRING
0317H TIME-OUT IN INTELLIGENT NETWORK BASED SUBSCRIBER SERVICE
031AH INCOMING CALLS BARRED WITHIN THE CUG
031CH SUBSCRIBER NOT A MEMBER OF THE CUG
031DH OUTGOING CALLS BARRED WITHIN THE CUG
0321H NO CUG SELECTED
0322H UNKNOWN CUG INDEX
0400H ATTENUATOR CONGESTION
0401H INTERWORKING UNIT CONGESTION
NUMBER NAME
DN078927Issue 1-0
159
DX200 Clear Code List Clear code index
Id:0900d80580635beb
0402H REGISTER TOTAL TIME EXCEEDED
0403H MFCU DEVICE CONGESTION
0404H PBRU DEVICE CONGESTION
0405H ERRONEOUS SERVICE REQUEST FROM CO-PROCESS
0406H CONNECTION FAILED IN GSW/SWI
0407H ERRONEOUS ANSWER FROM PARTNER PROGRAM BLOCK
0408H LENGTH OF CALLED SUBSCRIBER NUMBER EXCEEDED
0409H CONNECTION FAILED IN SSW/SWI
040AH CIRCUIT CONGESTION DUE TO TRAFFIC TYPE
040BH HOP COUNTER EXHAUST
0506H LINES OF LINE HUNTING GROUPS BARRED
0508H CHARGING ERROR
0509H FILE ERROR
050BH MODULE ROUTE OR SSW CONGESTION
050CH MFC-ASS-CHANNEL CLOSING MISSED
050DH FACILITY CONTROL FAILED
050FH UNSUITABLE MODULE CIRCUIT
0600H FILE RECORD CONGESTION
0601H MODULE OR V5 CONGESTION
0602H REGISTER CONGESTION
0603H NO RESPONSE FROM PARTNER PROGRAM BLOCK
0604H INTERNAL CALL LINK CONGESTION
0606H CONFERENCE DEVICE CONGESTION
0607H POLARITY REVERSAL FAILURE
0608H CHARGING NOT STARTED
0609H CALL CLEARED BY MML
060BH OVERLOAD CONGESTION
060DH STAGE CIRCUIT CONGESTION
060EH UNIT RESTARTED
060FH SUBSCRIBER MODULE OR V5 INTERFACE FAILURE, CALL CLEARED
0700H LONG AON REQUEST
0701H REGISTER ANALYSIS FAILED
0702H QUEUEING TIME EXCEEDED
0704H PARITY ERROR FROM PBRU/MFCU DEVICE
0705H MODULE OR V5 INTERFACE NOT AVAILABLE
0706H CALL INTERRUPTED DURING REGISTER ANALYSIS
0707H SUBSCRIBER MODULE RESTARTED
070AH FORCED CLEAR OF A CALL
NUMBER NAME
160 DN078927Issue 1-0
DX200 Clear Code List
Id:0900d80580635beb
Clear code index
070BH MODEM ERROR
070CH OVERLOAD CONTROL SYSTEM ERROR
070DH ANNOUNCEMENT SERVICE FAILURE
070EH CONFIGURATION ERROR
0710H NO ANALYSIS FOR CARRIER ACCESS CODE
0711H TARIFF NOT ACCEPTED BY TRANSIT EXCHANGE
0712H TARIFF NOT ACCEPTED BY ORIGINATING OR INTERWORKING EXCHANGE
0713H NO ISUP ROUTE
0714H ATTRIBUTE DIRECTED ROUTING MISMATCH
0715H REQUESTED FACILITY WAS NOT AVAILABLE ON THE OUTGOING ROUTE
0716H REQUESTED BEARER CAPABILITY COULD NOT BE FULFILLED ON THE ROUTE
0718H DIGIT ANALYSIS IN CENTRAL MEMORY RESULTED IN CONGESTION
0719H NO RESOURCE AVAILABLE FOR CALL
071AH IDENTIFIED CHANNEL NOT EXIST
071BH REQUESTED CHANNEL NOT AVAILABLE
071CH PACKET CONTROL UNIT CONGESTION
071DH POINT-TO-POINT PROTOCOL ERROR
0801H LENGTH OF ORIGINAL CALLED SUBSCRIBER NUMBER EXCEEDED
0802H LENGTH OF CALLING SUBSCRIBER NUMBER EXCEEDED
0803H INVALID CALLING SUBSCRIBER CATEGORY
0804H OUTGOING CIRCUIT CONGESTION
0806H IDENTITY OF CALLING SUBSCRIBER IS NOT AVAILABLE
0809H ERRONEOUS MFC SIGNAL FROM OUTGOING CIRCUIT
080AH ERRONEOUS MFC SIGNAL FROM INCOMING CIRCUIT
080BH NO B-NUMBERS TO SEND TO OUTGOING CIRCUIT
080CH UNKNOWN DECADIC SIGNAL FROM INCOMING CIRCUIT
080DH OUTGOING CIRCUIT OUT OF ORDER
080EH INCOMING CIRCUIT OUT OF ORDER
080FH CIRCUIT CONGESTION
0810H FACILITY NOT SUPPORTED
0811H NETWORK FAILURE
0813H SWITCHING EQUIPMENT CONGESTION
0814H CIRCUIT GROUP CONGESTION
0815H ACCESS BARRED TO THE CALLED SUBSCRIBER
0816H CALL FAILED, SEND SPECIAL INFORMATION TONE
0817H NETWORK, UNALLOCATED NUMBER
0818H NETWORK, LINE OUT OF SERVICE
0819H NETWORK, SUBSCRIBER NUMBER CHANGED
NUMBER NAME
DN078927Issue 1-0
161
DX200 Clear Code List Clear code index
Id:0900d80580635beb
081AH CONGESTION IN TERMINAL EXCHANGE
081DH CONGESTION IN INTERNATIONAL CALL
081EH CONTROLLED NOT READY
081FH NETWORK, OVERLOAD CONGESTION
0820H NETWORK MESSAGE CONTENT ERROR
0821H INVALID TRANSIT NETWORK SELECTION
0822H RECOVERY ON TIMER EXPIRY
0824H PCM FAULTY
0828H CONGESTION FROM NATIONAL NETWORK
0829H DIGITAL CIRCUIT MULTIPLICATION EQUIPMENT CONGESTION
0830H NUMBER PORTABILITY
0832H ROUTING ERROR
0833H DIGITAL CIRCUIT MULTIPLICATION EQUIPMENT FAILURE
0851H TRAFFIC TO CONGESTED DESTINATION POINT CODE RESTRICTED BY SIGNAL-LING
0900H NO MF FORWARD SIGNAL
0901H TOO LONG MF FORWARD SIGNAL
0905H TOO LONG MF BACKWARD SIGNAL
090CH PREMATURE ACKNOWLEDGEMENT TO SEIZURE IN OUTGOING CIRCUIT
090EH PREMATURE ANSWER
090FH ANSWER AFTER B BUSY
0A01H CLEARED FORWARD (SEIZING ACKNOWLEDGED SIGNAL MISSING)
0A02H INVALID MESSAGE FROM TRUNK CIRCUIT
0A03H INTERWORKING FAILED
0A04H TRUNK CIRCUIT PROTOCOL ERROR
0A05H CIRCUIT RELEASED BY CO-EXCHANGE
0A07H CALL FAILURE FROM OUTGOING CIRCUIT
0A08H INTER-EXCHANGE SIGNALLING OUT OF ORDER
0A09H ADDRESS COMPLETE MESSAGE TIME-OUT
0A0AH ADDRESS COMPLETE MESSAGE SENDING TIME EXCEEDED
0A0CH NO DIGITAL TRUNK
0A0DH NO ROUTE TO SPECIFIED TRANSIT OR TO DESTINATION
0A0EH NO CIRCUIT AVAILABLE IN TRANSIT NETWORK
0A0FH RESELECTION IN TRANSIT NETWORK APPLYING LOAD SHARING
0B02H TRANSIT/TERMINAL SIGNAL WAIT TIME SUPERVISION EXCEEDED
0B0FH LENGTH OF CHANGED CALLED SUBSCRIBER NUMBER EXCEEDED
0B11H MODEM COMMUNICATION ERROR
0B17H ADDRESS INCOMPLETE
NUMBER NAME
162 DN078927Issue 1-0
DX200 Clear Code List
Id:0900d80580635beb
Clear code index
0B18H SERVICE UNAVAILABLE
0B19H SERVICE INCOMPATIBLE
0B20H NETWORK ADDRESS EXTENSION (NAE) ERROR
0B21H DTE IS UNCONTROLLED
0B23H DUAL SEIZURE FROM BIDIRECTIONAL CIRCUIT
0B2AH BLOCKING RECEIVED
0B2BH PARAMETER DOES NOT EXIST OR IS NOT IMPLEMENTED
0B2CH INTELLIGENT NETWORK APPLICATION PROTOCOL ERROR
0B2DH INTELLIGENT NETWORK APPLICATION RESPONSE TIME-OUT
0B2EH MAXIMUM NUMBER OF TRIGGERING EVENTS IN A CALL HAS BEEN REACHED
0B2FH TCAP ERROR
0B30H ASN1 CODING OR DECODING ERROR
0B31H SELECTIVE CALL CONGESTION HAS PREVENTED CALL ATTEMPT
0B32H CALL RELEASE ORDERED BY INTELLIGENT NETWORK APPLICATION
0B33H CONTINUITY CHECK FAILURE
0B34H A-NUMBER IS NOT THE REGISTERED NUMBER OF AN INDIRECT SUBSCRIBER
0B35H TOO MANY FRAUDULENT ATTEMPTS TO USE CALLING CARD
0B36H CALLING CARD NUMBER SELECTED BY USER NOT FOUND
0B37H IN-SERVICE INTERRUPTED FOR SUSPECTED FRAUD
0B38H IN FALLBACK CODE ONE
0B39H IN FALLBACK CODE TWO
0B3AH IN FALLBACK CODE THREE
0B3BH IN FALLBACK CODE FIVE
0B3CH IN FALLBACK CODE FOUR
0B3DH IN DIALOG - ROUTING FAILURE IN SS7 NETWORK
0C00H DIAL WAIT TIME EXCEEDED
0C01H PROHIBITED DIALLING
0C02H INSUFFICIENT DIALLING FROM SUBSCRIBER SIGNALLING
0C04H CALLING SUBSCRIBER HAS DIALLED WRONG KEYWORD
0C05H CALLING SUBSCRIBER HAS NO RIGHT TO FACILITY
0C06H CALLING SUBSCRIBER HAS NO RIGHT TO STORE NUMBER
0C08H PREMATURE DIALLING
0C09H SERVICE OR FACILITY ACTIVATION RESTRICTED
0C0AH SERVICE OR FACILITY USAGE RESTRICTED
0C0BH INCONSISTENCY BETWEEN A- AND B-SUBSCRIBERS
0C0DH BEARER CAPABILITY NOT PRESENTLY AVAILABLE
0D00H SUBSCRIBER SIGNALLING MESSAGE CONTENT ERROR
0D01H SUBSCRIBER SIGNALLING MESSAGE FORMAT ERROR
NUMBER NAME
DN078927Issue 1-0
163
DX200 Clear Code List Clear code index
Id:0900d80580635beb
0D03H SERVICE OR FUNCTION NOT IMPLEMENTED
0D04H SUBSCRIBER SIGNALLING PROTOCOL ERROR
0D06H AOCC CHARGING ERROR
0D07H NO RESPONSE TO CALL ESTABLISHMENT: ALERTING OR CONNECT
0D08H GSM ERH 4.08 PROTOCOL TIMER EXPIRES
0D0BH DUAL LOG-IN
0D0FH ISDN-SUBSCRIBER FACILITY DIALLING REJECTED
0D10H MANDATORY INFORMATION ELEMENT MISSING
0D11H INVALID INFORMATION ELEMENT CONTENT
NUMBER NAME
164 DN078927Issue 1-0
DX200 Clear Code List
Id:0900d80580635beb
Glossary
GlossaryAOC-C Advice of Charge (charging)
ASN.1 Abstract Syntax Notation One
BCIE Bearer Capability Information Element
CAC Carrier Access Code
CAI Charge Advice Information
CCSU Common Channel Signalling Unit
CFU Call Forwarding Unconditional
CFB Call Forwarding Busy
CFNR Call Forwarding On No Reply
CUG Closed User Group
DTE Data Terminal Equipment
EIR Equipment Identity Register
HLR DX HLR
ISUP ISDN User Part
ITUP International Telephone User Part
IN Intelligent Network
ICxPRB IC1PRB, IC2PRB, IC3PRB and IC9PRB
MFC Multifrequency Code
MFCU Multifrequency Code Unit
MFST Multi Frequency Signalling Terminal plug-in unit
MWD Messages Waiting Data
NUP National User Part
PBRU Push Button Receiver Unit
PCM Pulse Code Modulation
PNP Private Numbering Plan
SCP Service Control Point
SSP Service Switching Point
TCAP Transaction Capabilities Application Part
TUP Telephone User Part
VLR Visitor Location Register