Pe Lab Manual 2016

8/20/2019 Pe Lab Manual 2016

1/44

LABORATORY MANUAL

POWER ELECTRONICS LAB ( 12EE63 )

SEMESTER: VI EEE

Compiled & Prepared by

1. Mrs. Hemalatha J N

2. Mrs. Prema V

DEPATRMENT OF ELECTRICAL A ND ELECTRONICS

E NGINEERING

R V COLLEGE OF E NGINEERING( AUTONOMOUS UNDER VTU )

BANGALORE-560059.

8/20/2019 Pe Lab Manual 2016

2/44

DEPARTMENT OF ELECTRICAL AND ELECTRONICS ENGINEERING

R V COLLEGE OF ENGINEERING ( AUTONOMOUS UNDER VTU )

POWER ELECTRONICS LAB ( 12EE63 )

LIST OF EXPERIMENTS

1. Static characteristics of SCR

2. Static characteristics of MOSFET and IGBT.

3. SCR turn-on circuit using synchronized UJT relaxation oscillator.

4. SCR digital firing circuit for a single phase controlled rectifier

5. Single phase full wave rectifier using R and R-L loads

(conventional & simulation)

6. An improved Series Inverter ( conventional & simulation)

7. Single phase full bridge parallel inverter connected to R load (conventional & simulation )

8.

Complementary Commutation ( conventional & simulation)

9. Auxiliary Commutation ( conventional & simulation)

10. Speed control of a separately excited DC motor using a MOSFET chopper

11. Speed control of single phase induction motor using AC voltage controller

12. Assignment (an additional experiment will be given to students, which they have todesign and implement themselves)

Prof. & HOD, EEE Department.

8/20/2019 Pe Lab Manual 2016

3/44

LIST OF EXPERIMENTS

I CYCLE

Expt. No Page No

1. Static characteristics of SCR 1

2. Static characteristics of MOSFET and IGBT. 3

3.

SCR turn-on circuit using synchronized UJT relaxation oscillator. 8

4. SCR digital firing circuit for a single phase controlled rectifier 11

II CYCLE

5. Single phase full wave rectifier using R and R-L loads (conventional & simulation) 16

6. An improved Series Inverter (conventional & simulation) 20

7. a. Single phase full bridge parallel inverter connected to R load

b. Simulation of bridge inverter 23

8. Complementary Commutation ( conventional & simulation ) 26

III CYCLE

9. Auxiliary Commutation (conventional & simulation) 29

10. Speed control of a separately excited DC motor using a MOSFET chopper 32

11. Speed control of single phase induction motor using AC voltage controller. 34

12. Assignment 36

ALSO

Question Bank 38

Viva Questions 40

8/20/2019 Pe Lab Manual 2016

4/44

POWER ELECTRONICS LAB(12EE63)

Department of EEE RVCE

1

I CYCLE

EXPT. NO 1

STATIC CHARACTERISTICS OF SCR

AIM: To obtain the static V-I characteristics of the given SCR

APPARATUS REQUIRED: Triac(BT-136), milli ammeter, rheostats, general purpose connecting

board.

CIRCUIT DIAGRAM:

PROCEDURE:

The SCR is a unilateral device. It is a current controlled device. Separate DC supplies are given to thegate and anode of the device as shown. The supply to the gate is lower than the anode supply.

1. The circuit is connected as shown. The terminals of the device are identified according to the pin diagram shown below:

C A G

2. Measuring the resistances between the gate and cathode and anode and cathode checks the

healthiness of the device. The resistances have to be high. The resistance between anode andcathode is higher than the one between gate and cathode.

BT136

8/20/2019 Pe Lab Manual 2016

5/44



2

3. Initially, a gate current of 1.5mA is supplied to the gate by adjusting the gate supply as well as

the 145 resistor in the gate circuit.

4.

The anode supply is now gradually increased. The voltage will be blocked by the device,

which will be recorded by the voltmeter which is connected across the anode and cathode of

the device.

5. As the voltage is further increased, for some value of the forward voltage, the device will

breakdown. This condition is called turn-on of the device. This condition is indicated by thevoltmeter across the device collapsing to about 1V. The voltage at which the device breaks

down is called the forward break over voltage, VBO. This voltage is noted down.

6. After the device starts conducting, which is also indicated by the ammeter in the anode circuitindicating a current, the anode supply is increased and the corresponding increase in the anode

current is noted and the readings are tabulated as shown. The procedure outlined in the abovesteps is repeated for another gate current, and tabulated.

Ig1= -- mA: VBO1= -- V Ig2= -- mA: VBO2= -- V

7. Using the readings tabulated for two values of gate currents. The V-I characteristics of the

SCR are plotted as shown below:

Ia (mA)

Ig2 Ig1

ILVak (V)

VBO2 VBO1

Ig1 > Ig2

-Ia (mA)

Sl.

No.

Anode current

Ia, in mA

Vak, Across

device in VSl.

No.

Anode current

Ia, in mA

Vak, Across

device in V

8/20/2019 Pe Lab Manual 2016

6/44



3

TO FIND THE VALUE OF HOLDING CURRENT:

To find the value of holding current, after turning the SCR, the forward voltage is slowly reduced justuntil the forward blocking voltage reappears across the device. The anode current at this point is

noted down. Typically its value will be around 5mA to 10mA.

EXPT. NO 2:

STATIC CHARACTERISTICS OF MOSFET AND IGBT

AIM: To obtain the static V-I characteristics of MOSFET and IGBT .

APPARATUS REQUIRED: MOSFET (IRF 730), two 0-30V power supplies, rheostat, 0-100

milliammeter, multimeter, connecting board and connecting wires/patch cords.

A. CHARACTERISTICS OF MOSFET

CIRCUIT DIAGRAM:

PROCEDURE:

The MOSFET is a voltage controlled static switch. It can be considered as the static equivalent of thevacuum tube triode.

1. The circuit can be connected as shown above after verifying that the device is healthy andidentifying the terminals of the device by means of the pin diagram below:

8/20/2019 Pe Lab Manual 2016

7/44



4

G D S

2. Apply a suitable voltage (15V) across the drain and source terminals of the device. Now

slowly increase the gate to source voltage by adjusting the supply till the device turns on

which is indicated by the ammeter showing a reading. The corresponding voltage across the

gate and source is called the threshold voltage whose value is noted down.

3. The readings for the drain characteristics are noted by increasing the Vds supply by keeping

Vgs constant. The procedure is repeated for another higher value of Vgs and Vds is increasedin steps and the corresponding increases in drain current Id are noted and tabulated as below:

Vgs1= ---V Vgs2= ---V

Drain Characteristics

Id(mA)

Vgs1

Vgs2

Vgs1 > Vgs2

Vds(volts)

Sl. No. Vds (v) Id (mA) Sl. No. Vds (v) Id (mA)

IRF730

8/20/2019 Pe Lab Manual 2016

8/44



5

3. For obtaining the transfer characteristics, the drain voltage Vds is fixed at some value (15v)

and the gate to source voltage is increased in steps and the increase in the drain current is

noted and tabulated. The procedure is repeated for a larger value of drain voltage (30V) and

the corresponding values of Vgs and Id are noted and tabulated as shown. The drain andtransfer characteristics are also shown below:

Vds1= ---V Vds2 = ---V

Transfer Charecteristics

Id (mA)

Vds1

Vds2

Vds1 > Vds2

Vgs(volts)

Vth

CALCULATION:

From the drain characteristics’ and transfer characteristics the device parameters like drain resistance

rd, trans conductance gm and amplification factor can be found using following equations.

gm = ΔId / ΔVg = ________ ohm-1 rd = ΔVds / ΔIds= ________ ohm

μ = rd x gm

Sl. No. Vgs (V) Id(mA)Sl. No. Vgs (V) Id(mA)

8/20/2019 Pe Lab Manual 2016

9/44



6

B. CHARACTERISTICS OF IGBT

APPARATUS REQUIRED: IGBT, two 0-30V power supplies, 0-2A ammeter, multi-meterconnecting board, connecting wires etc.

CIRCUIT DIAGRAM:

PROCEDURE:

1. After checking that the device is healthy, in the usual way, the circuit given above is

connected. The supplies are kept at the minimum (zero volts).

2. The IGBT is a switching device which is a voltage controlled device. From the output end it

works a NPN transistor. A minimum voltage at the gate is required to turn on the device, the

value of which is called the threshold voltage.

4. To start with, a voltage of 15V is applied to the collector circuit.

5. The gate to emitter voltage Vge is very slowly increased till the device switches on which isindicated by the ammeter in the collector circuit showing a reading. The value of Vge is noted

down.

6.

The collector to emitter voltage (Vce) is further increased to record the corresponding

increases in the collector current till it reaches saturation.

7. This procedure is repeated for another value of Vge and the readings are tabulated & a graph

of Vce against Ic is drawn for the two different values if Vge as shown below:

8/20/2019 Pe Lab Manual 2016

10/44



7

Vge1 = ----V Vge2 = ----V

Ic(mA)

Vge1

Vge2

Vge1 > Vge2

Vce (volts)

EXPT.NO 3

LINE SYNCHRONISED UJT TRIGGERING CIRCUIT

AIM: To study the UJT as a triggering device and obtain the waveforms of the triggering circuit. To

also study how the UJT can be used as a line synchronized device and record the waveforms of theload voltage and the SCR voltage.

APPARATUS REQUIRED: One UJT (2N2646), one 230V/18V, 150VA transformer, load resistor,one SCR, resistors, one 15V, 400mW zener diode, one pulse transformer, diodes (BY127/1N4001),

connecting board, patch cords, CRO.

CIRCUIT DIAGRAM: A line synchronized UJT triggering circuit for triggering an SCR connected

in a half wave rectifier circuit is shown below:

Sl.No. Vce in V Ic in ASl.No. Vce in V Ic in A

8/20/2019 Pe Lab Manual 2016

11/44



8

PROCEDURE:

1. After checking all the components, wire up the circuit as shown.

2.

After connecting the circuit, switch on the AC supply to the transformer. Connect theoscilloscope across the points shown and record the waveforms. One precaution to be

taken is that only one channel of the CRO is to be connected across the pulse

transformer output and the other cannel should not be connected to any other part

of the circuit.

3. The waveforms are shown below:

8/20/2019 Pe Lab Manual 2016

12/44



9

V

tVZ ZENER VOLTAGE WITH

SUPER IMPOSED PULSES

tVC

VPEAK

t

VPUL

t

4.

After verifying that the triggering circuit is working satisfactorily and the Pulses aretransferred to the secondary of the pulse transformer; the triggering circuit is connected to

the half wave controlled rectifier circuit shown:

5. The terminals marked G and K in the triggering circuit are connected to the gate and

cathode terminals of the SCR in the half wave rectifier circuit shown. The variable

resistor R in the triggering circuit is varied and the variation of the delay/triggering angle

8/20/2019 Pe Lab Manual 2016

13/44



10

is observed on the CRO. The voltage across the load and SCR are recorded and drawnto scale as shown below:

V V = Vmsint

t

VL

t

VSCR

t

Sl

No:

Firing Angle ( ) Vo (Practical) Vo (Theretical) =

8/20/2019 Pe Lab Manual 2016

14/44



11

EXPT. NO 4

SCR DIGITAL TRIGGERING CIRCUIT FOR A SINGLE PHASE

CONTROLLED RECTIFIER

AIM: To assemble a digital firing scheme to trigger an SCR in a half wave rectified circuit using

CD4047. To also study the method of trigger angle control or phase control of SCR.

APPARATUS REQUIRED: IC 741, IC CD 4047( 2 Nos), CL 100 ( 3 NOs) resistors and

capacitors.

CIRCUIT DIAGRA:

STAGE 1;

The above circuit is called a Zero Crossing Detector or ZCD which is a synchronizing circuit to be

synchronized to the ac supply. The op-amp 741 works as a comparator. The waveforms at point “A”

are shown below.

Input signal to ZCD from

Vi transformer

wt

out put of ZCD

12v

wt

-12v

o/p at A

wt

8/20/2019 Pe Lab Manual 2016

15/44



12

STAGE 2: CIRCUIT DIAGRAM

In stage 2 the square wave signal obtained is given as an input signal to a negative edge triggeredmonostable multivibrator using a CD 4047 I.C. The circuit of stage 2 is given below

Description of CD 4047

CD 4047 is a very versatile timer digital IC which has three important modes of operation, namelyfree running astable, positive edge triggered and negative edge triggered monostable and gated

astable modes. The connections given above are for negative edge triggered monostable. The 4047IC also has two outputs obtainable at pins 10 and 11. one output at pin 10 is the normal output. Its

complimentary output is available at pin 11. the pulse width of the output can be designed using the

relationship tm=2.48RC, where tm is the width of the pulse to be designed, R and C are theexternally connected components as shown. A fixed resistor potentiometer combination has been

used to vary the triggering angle of the line commutated SCR. The associated waveforms are shown

below.

A

wt

o/p at

pin 10

wt

o/p at

pin 11

8/20/2019 Pe Lab Manual 2016

16/44



13


The output signal from pin 11 of the negative edge monostable vibrator is given as a triggerinput to another CD 4047 operated in the true gated astable mode as shown in the diagram below.

The CD 4047 in the true gated astable mode, will convert an input pulse at pin 5, into very high

frequency pulses suitable for triggering an SCR. The input to pin5, called trigger input is givenfrom the emitter follower as shown which acts as a buffer. CL100 is the transistor used for the

buffer. The output from pin 10 ( normal output ) is obtained as a high frequency train of pulses. The

associated input and output waveforms of stage 3 are as shown below:

o/p at 11

wt

high frequency

o/p at 10of gated Astable wt

8/20/2019 Pe Lab Manual 2016

17/44



14


The output obtained from gated astable at pin 11 shown above which will be in the form of

high frequency pulses have to be amplified suitably in order to trigger an SCR. Therefore , from pin10 of the gated astable, the pulses are amplified using the following amplifier circuit

.

The output of the gated astable is given to a CL 100 based pulse amplifier. P and S are the windings

of a pulse transformer which will transmit the pulse from the input to the input.

These pulses are given to the gate of an SCR connected as a half wave rectifier circuit shown below

8/20/2019 Pe Lab Manual 2016

18/44



15

The output pulses obtained from secondary winding of pulse transformer are given to the gate of the

SCR. The output waveform is shown below.

V = VmsintV

t

VL

t

Vscr

t

Triggering angle can be varied by varying 100K pot in the monostable.

Sl

No:

Firing Angle ( ) Vo (Practical) Vo (Theretical) =

8/20/2019 Pe Lab Manual 2016

19/44



16

II CYCLE

EXPT NO 5

SINGLE PHASE FULL WAVE RECTIER USING R AND R-L LOADS

( CONVENTIONAL AND SIMULATION )

a. AIM: To connect a center-tapped rectifier circuit and to study the waveforms of the load

voltage, voltage across the SCRs and to show that the conduction of the SCRs will be beyond

180. To calculate the average value of the output voltage for triggering angles above and

below 90.

APPARATUS REQUIRED: A center-tapped transformer of rating 230/12-0-12V 150VA, two

SCRs, load resistor of 30, load inductance of 15mH, two 330, 3W resistors, two 100, 3W pots,two o.1uF capacitors, connecting wires, one CRO.

CIRCUIT DIAGRAM: The circuit diagram is shown below:

PROCEDURE:

1. The circuit shown above is connected after ensuring that the SCRs are healthy by checking

their gate to cathode and anode to cathode resistances.

2. To start with, the inductance of the load, i.e. the 15mH inductor is removed and the

waveforms across the load and the devices are observed as shown below, the CRO being

connected across the load resistor RL.

8/20/2019 Pe Lab Manual 2016

20/44

8/20/2019 Pe Lab Manual 2016

21/44



18

b. SIMULATION OF FULL WAVE CONTROLLED SEMICONVERTER

CIRCUIT DIAGRAM :

PROCEDURE:

1. Circuit is drawn as shown in pspice schematics

2. The values and attributes of components to be se as indicated in diagram

3.

select transient analysis and set step time as 10ns and final time as 35ms.

4. save the file and simulate circuit and observe the waveform across load as shown.

5. the same be repeated for RL- load and observe the output wave form

.

8/20/2019 Pe Lab Manual 2016

22/44



19

OUTPUT WAVE FORM:

R-L load

R-LOAD

8/20/2019 Pe Lab Manual 2016

23/44



20

EXPT NO 6:

IMPROVED SERIES INVERTER

AIM: To rig up a class-A based SCR series inverter and study its operation and observe thewaveforms of the load and capacitor voltage and to verify that the circuit behaves as an under damped

oscillatory circuit.

APPARATUS REQUIRED: Two SCRs, one 0-30V DC supply, commutating capacitor (4uF),

center-tapped inductance, CRO, load resistance, triggering card and patch cords.

CIRCUIT DIAGRAM:

TRIGGERING CARD

:

ASTABLE MONO -

STABLE

BLOCKING

OSCILLATORPULSE

AMPLIFIER

INVERTER MONO –

STABLE

BLOCKING

OSCILLATOR

PULSE

AMPLIFIER

G1K 1

G2 K 2

8/20/2019 Pe Lab Manual 2016

24/44



21

TRIGGERING REQUIREMENT:

In the power circuit, there are two SCRs, which have to be alternately turned on, and therefore, two

sets of high frequency pulses have to be generated which are out of phase and there is no overlap between the pulses.

PROCEDURE:

1. The circuit is connected after checking all the components. The power supply voltage knobs are

kept in minimum position and the current knobs are kept in maximum position.

2. The triggering card is also checked as indicated above and the pulses in both the channels of the

card are checked on the oscilloscope.

3. The supply to the power (SCR) circuit is energized by applying about 15V.

4. The supply to the triggering card is also varied very slowly, taking the precaution mentionedabove.

5. Once the required waveform is obtained, the voltage to the triggering card is not increased further.

6. The CRO channels are connected once across the load and once again across the capacitor and the

waveforms are noted down. Typical waveforms are shown below. The values of the inductance (onehalf), capacitance and the load resistance are measured using a digital L C R meter. These values are

used to check whether the circuit is behaving as an under damped oscillatory circuit by using the

equation: R

8/20/2019 Pe Lab Manual 2016

25/44



22

SIMULATION OF BASIC SERIES INVERTER

CIRCUIT DIAGRAM:

PROCEDURE:

1. Circuit is drawn as shown using pspice schematic editor, the values & attributes of the

components are set. The different attributes are DC=0, AC=1, V1=0, V2=10, TD=0, TR=1ns,

TF=1ns, PW=100us, PER=1ms for vpulse part for the thyristors 1 and DC=0, AC=1, V1=0,V2=10, TD=.05m, TR=1ns, TF=1ns, PW=100us, PER=1ms for vpulse part for the thyristors

2. In the set up analysis select transient analysis, and set print time as 10ns and final time as 3ms.

3. save the file and simulate to observe the output waveform.

OUTPUT:

8/20/2019 Pe Lab Manual 2016

26/44



23

EXPT NO 7:

MOSFET BASED SINGLE PHASE FULL BRIDGE INVERTER

CONNECTED TO R LOAD

a. AIM: To study the load voltage waveforms for different load resistances and observe and

record the load voltage waveforms with the switching transients.

APPARATUS REQUIRED: One parallel inverter module, a 40 tubular resistor, CRO, connectingwires.

CIRCUIT DIAGRAM:

PROCEDURE:

1. The circuit is connected as shown in the circuit diagram shown above. All the connections are

externally made on the module where the terminals are provided.

2. The load resistor is kept in the maximum position and the supply voltage is kept in minimum

position.

3. The supply switch is closed and the external switch shown which is provided on the module isalso switched on.

4. With the load in maximum position, the supply voltage is increased to about 15- 20V. Theload resistor is reduced a little and for this value of load, the waveforms across the load and

one of the SCRs are noted down, by connecting the CRO first across the load and then across

one of the SCRs.

5. The load resistor is reduced further and for this value of load resistance, the waveforms are

noted down.

8/20/2019 Pe Lab Manual 2016

27/44



24

The load voltage waveform is as shown below:

b. SIMULATION OF 1 PHASE BRIDGE INVERTER:

t

VL

8/20/2019 Pe Lab Manual 2016

28/44



25

PROCEDURE:

1. Circuit is drawn as shown using the pspice schematics

2. The values of the components and attributes of VPULSE are set for Q! and Q3 the

attributes for VPULSE are DC=0, AC=1, V1=0, V2=10, TD=0, TR=1ns, TF=1ns,

PW=0.5ms, PER=1ms and for Q2 and Q4 the attributes are DC=0, AC=1, V1=0, V2=10,TD=0.5ms, TR=1ns, TF=1ns, PER=1ms,PW=0.5ms

3. Select transient analysis set print step as 10ns and final time as 4 ms

4.

save the file and simulate to observe the output.

OUTPUT:

EXPT NO 8:

COMPLEMENTARY COMMUTATION

AIM: To connect a complementary commutation circuit and study and record the relevant waveforms and to calculate and verify the critical turn-off time or available circuit turn-off time from the

waveforms. To also observe the condition for commutation failure and identify the condition from the

waveforms.

APPARATUS REQUIRED: A 0-30V regulated supply, two SCRs, one 4uF capacitor, two tubular

145 resistors, one CRO, one triggering module, one digital LCR meter, connecting wires onemultimeter.

8/20/2019 Pe Lab Manual 2016

29/44



26

CIRCUIT DIAGRAM:

PROCEDURE:

1. The power circuit shown above is connected after ensuring all the components are in workingorder.

2. The triggering module is tested by energizing it by 10V DC supply and ensuring that thecurrent is well within the normal limits (0.25A).

3. The duty cycle of the astable in the triggering card is adjusted to 50%.

4. The outputs of the triggering card namely G1K1 and G2K2 are checked.

5. The gates of both the SCRs are connected to the triggering card outputs.

6. To start with the power circuit is energized with 15V.

7. The supply to the triggering card is slowly increased till the proper output is observed in the

CRO, which is connected across one of the 145 load resistors.

8. The CRO is next connected across the capacitor and the voltage across the capacitor is

observed and recorded.

9. The CRO is connected across one of the SCRs and the voltage across it is recorded. From this

waveform, the critical or circuit turn-off time is ‘toff’ is noted down.

10.

The load resistance is varied and the influence of load current on ‘toff’ is noted down.

11. The digital LCR meter is used to measure the values of C and R and ‘toff’ is calculated as:

toff = 0.6931RC.

A set of typical waveforms are shown below:

8/20/2019 Pe Lab Manual 2016

30/44



27

iC

vCvC

iC

t

- V iC = Capacitor current

vC = Capacitor voltage

vL

t

SIMULATION OF COMPLEMENTARY COMMUTATION

8/20/2019 Pe Lab Manual 2016

31/44



28

PROCEDURE:

1. The circuit diagram is drawn as shown using pspice schematic editor

2. The values of components are set and the attributes for VPULSE part to be set are for

thyristor 1 DC=0, AC=1, V1=0, V2=10, TD=0, TR=1ns, TF=1ns, PW=0.5ms, PER=1ms for

thyristor 2 DC=0, AC=1, V1=0, V2=10, TD=0.5m, TR=1ns, TF=1ns, PW=0.5ms, PER=1ms

3. select transient analysis set print time as 10us and final time as 4ms

4. save the file and simulate to see the output.

8/20/2019 Pe Lab Manual 2016

32/44



29

III CYCLE

EXPT NO 9:

AUXILIARY COMMUTATION

AIM: To study the principle of auxiliary commutation or impulse commutation.

APPARATUS REQUIRED: Two 0-30V DC supplies, two SCRs, one triggering card (both

channels), L, C, CRO and patch cords.

CIRCUIT DIAGRAM:

PROCEDURE:

As two SCRs are used, the triggering requirements are the same as the series inverter. Two sets of

pulses out of phase with each other are to be generated.

1.

The circuit is connected as shown in the figure.

2. Power supply is first given to the SCR circuit (about 15V).

3. To start with; the auxiliary SCR is triggered, with the gate of the main SCR kept open.

4. The capacitor will charge with its upper plate positive to VDC.

5. The main SCR is now turned on by connecting the gate of this SCR to the gate terminal on thetriggering card. (The triggering card would already be checked as given earlier).

8/20/2019 Pe Lab Manual 2016

33/44



30

6. The relevant waveforms across the load and across the capacitor are obtained, noted down and

plotted to scale. Typical waveforms are shown below.

GATEPULSES iGA iGM iGA

t

iC

vC

2VDC / R LVDC

VDC / R L

t

VDC / R L

vL

VDC / R L

t

8/20/2019 Pe Lab Manual 2016

34/44



31

SIMULATION OF AUXILIARY COMMUTATION

PROCEDURE:

1. The circuit diagram is drawn as shown using pspice schematic editor

2. The values of components are set and the attributes for VPULSE part to be set are for thyristor1 DC=0, AC=1, V1=0, V2=10, TD=0, TR=1ns, TF=1ns, PW=0.5ms, PER=1ms for thyristor 2

DC=0, AC=1, V1=0, V2=10, TD=0.5m, TR=1ns, TF=1ns, PW=0.5ms, PER=1ms

3. select transient analysis set print time as 10us and final time as 4ms

4. save the file and simulate to see the output.

OUTPUT:

8/20/2019 Pe Lab Manual 2016

35/44



32

EXPT NO 10:

SPEED CONTROL OF A SEPARATELY EXCITED DC MOTOR

USING A MOSFET CHOPPER

AIM: To build a single quadrant MOSFET based chopper using a suitable control circuit. To varythe duty cycle of the chopper and hence vary the average voltage of the chopper. To also study the

variation in speed of the motor with respect to the duty cycle of the chopper.

APPARATUS REQUIRED: 4047 CMOS timer IC’s (2 Nos),resistors and capacitors, CL100

(2 Nos), one PMDC 12V motor.

CIRCUIT DIAGRAM:

FIRST STAGE:

The CMOS timer IC(4047) is connected as an astable in the free running mode as shown.

Pins 4,5,6 and 14 connected to vcc . Pins 7,8,9,12 connected to ground.

The output from pin 10 is taken through an emitter follower which is a buffer.

The output of the emitter follower is given as a trigger input to another CD 4047 timer IC connectedto work as a monostable which is negative edge triggered. The circuit of the second stage is as shown

below.

8/20/2019 Pe Lab Manual 2016

36/44



33

CIRCUIT DIAGRAM:

Pins 4,8,14 are shorted and connected to VCC .

Pins 5,9,7 and 12 are shorted and connected to ground.

In the monostable, the duty cycle can be varied by including a variable resistance between pins 2 &3.The waveforms of the two stages are shown below.

8/20/2019 Pe Lab Manual 2016

37/44



34

Pulse of various widths can be obtained, by simply varying the variable resistance in the monostable

circuit.

The power circuit using the MOSFET is rigged up as shown in the figure.

POWER CIRCUIT:

The PMDC motor is connected as shown. The output of the monostable is buffered and connected to

the MOSFET between the gate and source as shown.

PROCEDURE:

1. Rig up the control circuit stage by stage and check the outputs.

2. Connect the control circuit to the gate of the MOSFET after connecting the power circuit .

3. Vary the duty cycle and record the voltage across the motor in the DMM connected across the

motor as shown.

4. Plot a graph of duty cycle versus the voltage across the motor.

8/20/2019 Pe Lab Manual 2016

38/44



35

EXPT NO 12:

SPEED CONTROL OF 1-PHASE INDUCTION MOTOR

USING AC VOLTAGE CONTROLLER.

AIM: To control the speed of a universal motor and a single-phase induction motor and to study the

variation of the output voltage with the control voltage and to draw the graph of the same .

APPARATUS REQUIRED: Two SCRs, one triggering card (both channels)I phase induction motor

and patch cords.

CIRCUIT DIAGRAM:

PROCEDURE:

1) The circuit is connected as shown in the figure, after ensuring that the devices are in good

working condition. The triggering module for the above circuit is energized with a 10V dual

supply and the triggering signals are observed on the CRO.

2) The triggering circuit is connected to the gates of the respective SCRs and the supply to the

power circuit is given.

3) A moving 0-250V voltmeter is connected across the motor terminals and a DMM is connected

across the pedestal voltage pot. The pedestal pot is slowly varied and the corresponding pedestal voltage and the voltage across the motor are noted down and tabulated as shown

below:

Sl No: Pedestal Voltage Motor Voltage

~~**~~**~~**~~

8/20/2019 Pe Lab Manual 2016

39/44



36

QUESTION BANK.

1. Obtain the static characteristics of the given SCR, clearly indicating the switching region.

Demonstrate that the gate current has no effect on the device after it is turned on.

2. Experimentally obtain the latching current of the given SCR. Also demonstrate that there will

be a drastic fall in the break-over voltage with a marginal increase in the gate current

3. Experimentally obtain the constants of the given MOSFET?

4. Obtain experimentally, the static characteristics of the given MOSFET and hence find its

constants.

5. Experimentally obtain the static characteristics of the given IGBT.

6. Obtain the characteristics of the given IGBT, clearly indicating the various regions of

operation

7. Generate high frequency pulse using a UJT, relaxation oscillator. Using these pulses, trigger

an SCR operating off a sinusoidal supply. Show that the triggering circuit is synchronized

with the power circuit from waveforms.

9. Rig-up a line synchronized UJT relaxation oscillator circuit to trigger an SCR in a HW

rectifier circuit. Measure the range of trigger/delay angles that can be obtained.

10. Rig up circuit for improved series inverter.. Form the load waveform, calculate the frequencyof oscillation. Also obtain the capacitor voltage waveform..

11. Simulate a basic series inverter. From the load waveform calculate the frequency ofoscillation. Also obtain the capacitor voltage waveform .

12. Assemble a suitable circuit to control a stepper motor in both the directions.

13. Wire up circuit to demonstrate how it is possible to commutate a load carrying SCR by

another SCR. Obtain all the relevant waveforms and draw to scales and hence calculate thefrequency of oscillation.

14. Simulate complementary commutated circuit to obtain relevant waveforms and calculate

frequency of oscillations.

15. Experimentally demonstrate the principal of auxiliary commutation. Draw all the relevant

waveforms to scale. Verify the frequency of oscillation obtained by measuring thecommutating elements.

8/20/2019 Pe Lab Manual 2016

40/44



37

16. Simulate a circuit for an auxiliary commutation. Draw all the relevant waveforms to scale.

Verify the frequency of oscillation obtained by measuring the commutating elements.

17. Show experimentally how turning on and SCR will automatically turn-off another conductingSCR. Record all the waveforms and hence obtain critical turn off time verify the value

obtained by measuring the commutating capacitor.

18. Demonstrate the principal of complementary commutation. Draw all the relevant wave forms

to scale. Find the value of the commutating capacitor from the critical turn-off time.

16. Rig-up a simple triggering circuit to generate high frequency pulse, using digital IC’s. Show

the waveforms at various stages of the circuit.

17. Wire-up digital firing circuit and hence generate high frequency firing pulse. Using these

pulses, trigger an SCR. Draw the waveforms at all the stages to scale.

18. Control the speed of a PMDC motor using a suitable DC chopper circuit. Experimentallydemonstrate that the speed of the motor controlled is directly proportional to the duty cycle of

the chopper.

19. Design and assemble a FWR circuit (using 2 SCRs) using the RC triggering principle. Obtain

and draw to scale the following waveforms.

(i) Voltage across load and SCR for a resistive (R) load.(ii) Voltage across the load and SCR for an inductive load (R-L) load. Also for an R-L

load determine from the waveforms, the triggering angle for conduction and discontinuous

conduction.

20. Design a UJT firing circuit to generate triggering pulses of a frequency of 500 Hz to fire anSCR in a HWR circuit. Obtain the range of triggering angles. Show all the relevant

waveforms in the UJT firing circuit.

21. Rig up a circuit for capacitor commutated single phase parallel inverter feeding a resistive

load and obtain load waveform.

22. Control the speed of the given 1 Induction motor using a suitable power circuit. Draw agraph of the stator voltage against the control voltage.

23. Rig-up a single phase voltage controller circuit with its associated triggering circuit. Control

the speed of the given 1 Induction motor from the converter in the open loop. Draw a graphof converter output versus the control voltage.

24. Simulate single phase bridge inverter circuit and obtain the relevant waveforms.

*****

8/20/2019 Pe Lab Manual 2016

41/44



38

VIVA VOCE QUESTIONS.

1.

What are the various types of thyristors?

2. What is a commutation circuit?

3. What is the difference between a thyristor and TRIAC?

4. What is the gating characteristics of a GTO?

5. What is a converter?

6. What is the principle of ac – dc conversion?

7. What is the principle of ac – ac conversion?

8. What is the principle of dc – dc conversion?

9. What is the principle of dc – ac conversion?

10. What are the steps involved in designing power electronic equipments?

11. What are the peripheral effects of power electronic equipments?

12.

What are the differences in the gating characteristics of thyristors and transistors?

13. What are the differences in the gating characteristics of BJTs and MOSFETs?

14. What is the gating characteristics of an IGBT?

15. What are the differences between BJTs and MOSFETs?

16. Explain the V I characteristics of a thyristor and point out the various regions.

17. What is the OFF state of a thyristor?

18. What is the ON state of a thyristor?

19. What is the relevance of latching current of a thyristor?

20. What is the relevance of holding current of a thyristor?

21. Analyze the behavior of thyristor by using two transistor models.

22. What is the process of regeneration during the turn ON process of thyristor?

8/20/2019 Pe Lab Manual 2016

42/44

8/20/2019 Pe Lab Manual 2016

43/44



40

45. What is meant by reversal time in a self commutated circuit?

46.

Explain the principle of impulse commutation. Why is it called so?

47. Explain the principle of resonant pulse commutation. Why is it called so?

48. Explain the complementary commutation principle.

49. Why is commutation time a critical factor in choppers and inverters?

50. Why should the available reverse bias time be greater than the turn OFF time of a thyristor?

51. What is the purpose of connecting an anti-parallel diode across the main thyristor with or

without a series inductor?

52. What are the requirements of a commutating capacitor?

53. What is the ratio of peak resonant to load current for resonant pulse commutation that would

minimize commutation losses?

54. How is the voltage of the commutating capacitor reversed in a commutation circuit?

55. What is line commutation?

56.

What is a controlled rectifier?

57. What is delay angle control of converters?

58. What is a semi converter? Draw two semi converter circuits.

59. What is the function of a free wheeling diode? Does a semi converter require a free wheeling

diode?

60. What is a full converter circuit? Does this circuit require a free wheeling diode?

61.

What is the principle of phase control?

62. What is the inversion mode of converter?

63. Why are harmonics present in converter circuits?

64. What is extinction angle of converters?

65. What are continuous and discontinuous current modes in converters? Why is discontinuous

current mode not preferable?

8/20/2019 Pe Lab Manual 2016

44/44


66. How is the output voltage of a phase controlled converter varied?

67.

Why is it preferable to have an inductor in a converter circuit?

68. What is the effect of line inductance in converter circuit?

69. What is overlap angle in line commutated circuits?

70. What is a commutation “notch” in a line commutated circuit?

71. Why is a fully controlled converter preferable over a half controlled (semi converter) from the

point of view of harmonics?

72.

Does the input power factor of a converter depend on the load power factor?

73. In a fully controlled single phase converter, if one of the thyristor fails, what is the effect onthe converter?

74. What are the advantages and disadvantages of on - off control?

75. What are the advantages and disadvantages of phase angle control?

76. What are the effects of load inductance on the performance of ac voltage controllers?

77.

What is a unidirectional controller? What are its disadvantages?

78. What is a universal motor? Explain its principle of operation.

79. What is the principle of operation of a step down chopper?

80. What is pulse width modulation control of a chopper?

81. What is time ratio controller (TRC)?

82. What is the effect of load inductance on ripple current?

83. What are the performance parameters of a chopper?

84. What are the advantages and disadvantages of auxiliary commutation?

85. What is duty cycle of a chopper circuit?

~*~*~*~*~

Date post:	07-Aug-2018
Category:	Documents
Upload:	mukundkulkarni
View:	220 times
Download:	0 times

Pe Lab Manual 2016

Documents