TUGAS

PERALATAN DAN PENGANGKUTAN

TAMBANG BAWAH TANAH

OLEH :

ANDI MUHAMMAD SHAFWAN

08.11.108.701602.000263

PROGRAM STUDI TEKNIK PERTAMBANGAN

FAKULTAS TEKNIK

UNIVERSITAS KUTAI KARTANEGARA

TENGGARONG

2010

1. Toreq 11500 scraperThe capacity and profile of this model fits the requirements of larger front wheel assist and 4-wheel drive tractors. It is designed with a lower center of gravity for increased side slope stability. 150-250 horsepower rubber tire tractors or 50-75 horsepower crawlers are its prime movers.

 

Specifications Capacity Heaped..11.5 Cubic Yards (10.5 Cubic Meters) Capacity Struck..8.6 Cubic Yards (11.15 Cubic Meters) Width of Cut..98 Inches (249 cm) Overall Width..116 Inches (295 cm)Depth of Cut..10 Inches (25.5 cm)Depth of Spread..0-15 Inches (0-38 cm) Ground Clearance..17 Inches (43 cm) Apron Opening..59 Inches (149cm) Overall Length..306 Inches (777 cm) Wheel Base..196 Inches (498 cm) Overall Height..80 Inches (187 cm) Weight..10,500 Pounds (4,590 kg) Tire Size (Front)..16.5 X 16.1 R-3 Tread 10 Ply Tire Size (Rear)..18.4 X 26 R-3 Tread 10 Ply Cutting Edge..3-Piece Carbon Steel .625 Inches Thick (1.6 cm)

Hydraulic SpecificationsRequires 3-Spools Bowl Lift Cylinders..4.0 X 18 (2) Front Gate Cylinders..3.0 X 13 (2)

Soil Ejector Cylinders..4.0 X 62 (1) Approximate Tractor Size..150-250 HP (Rubber Tire) 50-75 HP (Crawler)

Standard Features 360 Degree Swivel Hitch Knuckle Block Steering Hitch Industrial Style Cylinders 18 Inch Rear Spill Plate Tire Stem Protectors Drop Front Dolly

Options Frost Blades Sequenced Hydraulic Circuits Tire Sizes Hydraulic Mast Cylinder Mount

2. GD HEE SLUSHER Double Drum

Model HEE U.S. Metric

Rated Capacity - Rope Pull at 80 PSI 

lbs. 1100 498.9 kg

Rope Speed  at Rated Capacityft. per min.

15045.7 meters/min

Rope Speed at Stalling Point lbs. 2600 1179 kg

Maximum Capacity of Each Drum

1/4" (6.3 mm) Cable3/8" (6.3 mm) Cable1/2" (6.3 mm) Cable

ft.38017095

115.8 m51.8 m28.8 m

Working Capacity of Each Drum

1/4" (6.3 mm) Cable3/8" (6.3 mm) Cable1/2" (6.3 mm) Cable

ft.27912671

85 m38.4 m21.6 m

Horse Power hp 6.5

Size Foundation Bolt Holes in. 11/16 17.5 mm

Net Weight Without Cable Guides lbs. 312 141.5 kg

Net Weight of Cable Guides lbs. 44 19.9 kg

Air Pressure Recommended lbs. gauge 70 to 10031.7 - 45.3 kg

Size Air Hose Recommended in. 1 25.4 mm

Shipping Weight with Cable Guides lbs. 411 106.4 kg

Dimensions Boxed for Export in. 18x19x36451, 483, 914 mm

Cubic Measurement Boxed for Export

cu. ft. 7 .19 m^3

3. AD30 Underground Articulated TruckThe AD30 underground articulated truck is designed for high production, low cost-per-ton hauling in smaller underground mining applications. Rugged construction and easy maintenance guarantee long life with low operating costs.

EngineEngine Model Cat® C15 ACERT™Rated Power 1800 RPMGross Power - SAE J1995 304 kWFlywheel Power 281 kWNet Power - SAE J1349 281 kWNet Power - ISO 9249 281 kWNet Power - 80/1269/EEC 281 kWBore 137.2 mmStroke 171.5 mmDisplacement 15.2 L

Operating SpecificationsGross Machine Operating Weight 60000 kgNominal Payload Capacity 30000 kg

Body CapacitiesDump Body – Standard 14.4 m3Dump Body – Optional 17.5 m3Ejector Body – Optional 15.2 m3

WeightsEmpty 30000 kgFront Axle 20250 kgRear Axle 9750 kgLoaded 60000 kgFront Axle 26520 kgRear Axle 33480 kg

Weight DistributionFront Axle 67.5 %Rear Axle 32.5 %Front Axle 44.2 %Rear Axle 55.8 %

Body HoistRaise 10.5 SecondsLower 11.2 SecondsTotal Cycle Time 21.7 Seconds

Turning DimensionsOutside Clearance Radius 8571 mmInside Turning Radius 5030 mmFrame Oscillation 10 DegreesArticulation Angle 42.5 Degrees

TransmissionForward 1 6.8 km/hForward 2 12.3 km/hForward 3 22.3 km/hForward 4 40.8 km/hReverse 1 7.8 km/hService Refill CapacitiesEngine Crankcase with Filter 38 LTransmission 67 LHydraulic Tank 145 LCooling System 76 LFront Differentials and Final Drives 56 LRear Differentials and Final Drives 56 LFuel Tank 500 L

TiresTire Size 26.5 X R25 Radials

StandardsBrakes ISO3450, AS2958.1, CAN-CSA424.30-M90Cab/FOPS ISO3449, SAEJ231, AS2294.3, EN13627Cab/ROPS ISO3471, SAEJ1040, AS2294.2, EN13510

DimensionsOverall Width 2650 mmTunnel Clearance Width 4000 mmTunnel Clearance Height 4000 mmHeight to Top of Load (2:1) 3133 mmLoading Height 2385 mm

Overall Height - Body Raised 5602 mmHeight to Top of ROPS 2600 mmOverall Length 10153 mmWheelbase 5200 mmGround Clearance 400 mmDump Clearance 558 mmRear Wheel to Body Raised 1061 mmRear Axle to Tail 1608 mmMax Overall Length 10743 mmCenterline of Front Axle to Centerline of Hitch 1800 mmFront Axle to Front Bumper 3345 mmHeight to Top of Body 2547 mmOverall Tire Width 2650 mm

Final DrivesDifferential Ratio 3.38:1Final Drive Ratio 4.76:1Total Reduction Ratio 16.09:1

4. R2900G Underground Mining LoaderCompact design, high engine power, higher torque rise, stronger components and excellent maneuverability ensures the R2900G is a solid performer.

EngineEngine Model Cat® C15 ACERT™Rated Power 1900 RPMGross Power - SAE J1995 321 kWFlywheel Power 269 kWNet Power - SAE J1349 290 kWNet Power - ISO 9249 288 kWNet Power - 80/1269/EEC 321 kWBore 137.2 mmStroke 171.5 mmDisplacement 15.2 L

Operating SpecificationsNominal Payload Capacity 17200 kgGross Machine Operating Weight 67409 kgStatic Tipping Load Straight Ahead Lift Arms Horizontal 39923 kgStatic Tipping Load Full Turn Lift Arms Horizontal 34069 kgBreakout Force (SAE) 27346 kg

WeightsEmpty 50209 kgFront Axle 23057 kgRear Axle 27152 kgLoaded 67409 kgFront Axle 50220 kgRear Axle 17189 kg

Bucket CapacitiesBucket Capacity - Std. 7.2 m3Bucket Width (Over cutting edge) 3154 mmBucket Capacity – Optional 8.3 m3Bucket Capacity – Optional 8.9 m3

Hydraulic Cycle TimeRaise 9.2 SecondsDump 3.4 SecondsLower, empty, float down 3.1 SecondsTotal Cycle Time 15.7 Seconds

Turning DimensionsOutside Clearance Radius 7323 mm

Inner Clearance Radius 3383 mmAxle Oscillation 8 DegreesArticulation Angle 42.5 Degrees

TransmissionForward 1 5 km/hForward 2 8.8 km/hForward 3 15.2 km/hForward 4 25.3 km/hReverse 1 6.2 km/hReverse 2 10.9 km/hReverse 3 18.6 km/hReverse 4 26.4 km/h

TiresTire Size 29.5x29 34 PLY STMS

StandardsBrakes ISO3450, AS2958.1, CAN-CSA424.30-M90Cab/FOPS ISO3449, SAEJ231, AS2294.3, EN13627Cab/ROPS ISO3471, SAEJ1040, AS2294.2, EN13510

DimensionsOverall Tire Width 2898 mmOverall Width 3176 mmTunnel Clearance Width 4500 mmHeight to Top of ROPS 2886 mmHeight to Top of Hood 2371 mmOverall Height - Bucket Raised 6179 mmBucket Pin Height at Max Lift 4539 mmDump Clearance at Max Lift 6179 mmOverall Length (Tramming) 10949 mmGround Clearance 465 mmWheelbase 3780 mmDump Angle at Max Lift 42 DegreesMaximum Dump Height 5427 mmCenterline of Front Axle to Centerline of Hitch 1890 mmCenterline of Back Axle to Centerline of Hitch 1890 mmLength - Rear Axle to Bumper 3572 mmOverall Length (Digging) 11302 mmDigging Depth 52 mm

Tunnel Clearance Height 4000 mm

Service Refill CapacitiesEngine Crankcase with Filter 34 LTransmission 62 LHydraulic Tank 140 LFuel Tank 854 LFront Differential and Final Drives 119 LRear Differential and Final Drives 127 LCooling System 75 L

5. Rocker shovel MODEL 630

Specifications# Detail Mod 630

A Overall Length 2845mm

B Body Length 2000mm

C Machine Height 1510mm

D Overall Height 3225mm

E Discharge Height 1900mm

F Discharge Length 305mm

  Machine Width 1490mm

  Width With Step Plate 1745mm

  Clean Up Width Unlimited

  Track Gauge 1490mm

  Total Mass 4695Kg

  Bucket Capacity 0.39 cu met

  Loading Cycle 8 seconds

  Loading Capacity 2.0 cu met/min

  Motors 3* Mod 271

  Air Consumption 18 cu met/min

  Air Pressure Range 520 - 860Kpa

  Air Hose Diameter 50mm

6. KWJ-1 Underground Loader (Deuz Engine, 1cbm)

Product Description Underground loader Brief Introduction WJ-1 diesel loader adopts Deutz diesel engine driving, and matches purifier to clean-up the off-gas. WJD-1 electric loader adopts AC380V motor-driven. Both scrapers are hydraulic mechanical transmission, four wheel drive, central articulated, full hydraulic steering, and equipped with front bucket and front-dump. Main Characteristic: 1. Hydraulic transmission; 2. 4 wheel drive and smooth cutting-resistant tires; 3. Articulated hinge frame; 4. Complete hydraulic steering; 5. Hydraulic brake;

Model: WJ-1/WJD-1  underground loader Bucket capacity: 1/1m3 Rated loading: 1.7/1.7T Max traction force: 50/50KN Min. Ground clearance: 193/193mm Max. Shovel force: 45/45KN Travel speed: 0-12.5/0-8KM/H Max. Discharge height: 990/1110mm Gradeability: ≥ 12o/≥ 12o   Min. Turning radius: Outside of shovel 4100/4500 Inside of rear wheel: 2350/2350mm Max. Turning angle: About 36o/about 36o   Tire spec(smooth side): 10.00-20 / 10.00-20   Swinging angle of rear axle: About 8o/about 8o   Wheelbase: 1872/1860 mm Overall dimension: L(travel position): 5510/5800 W: 1268 / 1270 H(to ceiling) 1900/1956 mm Operating Weight: 6500 / 7000KG Cable effective length: 75m

Main parts and components: 1. Power:

(WJD-1)electric motor: Y225M-4 45KW (WJ-1)diesel engine: Germany BF4M2011 50KW (original imported) F4912W 42KW (assembled in China)

2. Transmission system Oil pump: ACA392114ROA(Eaton) Motor: ACE544114MAA(Eaton) Pilot pressure: 1.8MPa Travel pressure: 0-35MPa

3. Braking system Paring brake: Central disc hydraulic brake Working brake: Hydraulic brake

7. Crawler Digging Arm Loader (Bucket Loader) (LWL-150)

Product Description Crawler Digging Arm Loader (bucket loader)LWL-150 crawler digging arm loader is a kind of continuous production and efficient loader.It is mainly applied to railway tunnel construction, mining roadway excavation, waterprojects and defense in the loading operation.

The machine adopts backhoe system including bucket, boom and arm to excavate mining slag, and then through its own scraper conveyor to transport into the rear dump truck or other transportation equipment.

This model has oil motor, and the structure is compact, mobile and flexible. In addition, it is motor-driven, hydraulic transmission, the pilot valve operation, steady work, advanced design and easy to maintain.

Main Performance and Spec: Loading capacity: 150 m3/h Travel speed: 2-4 m/s Dumping distance: 2550 mm Dumping height: 2685 mm Cutting height: 4400 mm Digging depth: 900 mm Digging distance: 3470 mm Gradeability: 10 Power: 55 kw Ground pressure: 0.188 MPa Tank capacity: 560 L Whole weight: 15100 KG Overall dimension (L*W*H): 9500*2030*2415 mm Production rate (Piece/min): 35 Workday output (Piece): 12000 Total power (KW): 30 Number of staff: 15 Tiles specification (mm): 420*330

8. Lokomotif & LoriFO CC200Filed under: Uncategorized — admin @ 13:53 This section is a copy of the article in Diesel Railway Traction, April 1954

CC200 Locomotives for IndonesiaAmerican design capable of alteration from triple-bogie to twin-bogie typeTHE stringent weight limitations on the main line locomotives – steam and diesel – of the Indonesian State Railways have been a feature of post-war orders, and in the new 1,200 h.p. diesel-electric locomotives have led to an unusual wheel arrangement and to a simple modification which can be put into effect whenever track and bridges may be strengthened. The 27 locomotives recently shipped by General Electric (America) have the Co-B-Co wheel arrangement, whereby a 96-ton locomotive has a maximum axle load of 12 tons; but the body and underframe have been made strong enough to enable the centre bogie to be withdrawn when track and underline structure conditions improve, so that a Co-Co locomotive of about 92 tons weight and 15½ tons maximum axle load will then result.In their general lines and characteristics these locomotives follow closely the maker’s standard practice adapted to the 3 ft. 6 in. gauge. The wheels are 35.6 in. dia., each three-axle truck has a wheelbase of 7 ft. 6 in. Pivot centres of the outer six-wheels trucks are pitched at 31 ft. 4 in., and total wheelbase is 43 ft. 2 in. Overall height is 12 ft. and maximum width 8 ft. 8½ in. Minimum curve which the locomotive will traverse at slow speed is 460 ft. radius, and top speed is 62 m.p.h. Starting tractive effort at 30 per cent adhesion is 47,500 lb. and the continuous effort is 28,600 lb. at 17 m.p.h. Fuel capacity is 420 gal.Fabricated rolled steel sheets, plates and shapes make up the underframe and superstructure. Roof and sides of the driving cabs are insulated with a flameproof material. Bogie frames are fabricated from plates and shapes by electric welding and have lubricated centre plates equipped with hard steel liners. The trucks themselves are of the fully-equalised swing bolster types, with wheels having separate tyres. Hard steel thrust wearing faces are fitted to the roller-bearing axleboxes. Straight air brakes are applied to the locomotive with vacuum equipment for the train, and operate also in conjunction with dead-man control. A three-cylinder combined compressor-exhauster set has two of its cylinders acting as an exhauster and the third as compressor.

An Alco 12-cylinder V engine provides the power and is set to give a main generator input of 1,200 b.h.p. from the 9 in. by 10½ in. cylinders when running at 1,000 r.p.m. This engine and its generator are supported on a common base resiliently mounted on the locomotive underframe. The radiator banks are mounted on the sides at one end of the engine room; they are cooled by a two-speed electrically-driven fan, and the equipment is designed to keep the engine cool at ambient temperatures of 90 deg F. and at an altitude of 1,500 ft.The electrical equipment is characterised by a main generator having three gear-driven auxiliaries, viz., an amplidyne exciter for excitation of the main generator fields; a constant voltage auxiliary generator to provide battery charging, lighting and control power at constant potential over the full operating range of engine speed; and a variable-voltage auxiliary generator to provide for the traction motor blower and radiator fan. The storage battery is a 32-cell lead-acid unit. There are six force-ventilated nose-suspended motors. There is one traction-motor blower group for each truck and the air is taken from inside the cab above the platforms. The reverser and line contactors are operated electro-pneumatically; all other contactors and relays are electro-magnetic. The traction motors are connected in two-series-three-parallel and six-parallel groups.

Specifications Table

Locomotive Manufacturer General Electric Co. USA

Length 17,197 mm

Width 2,819 mm

Height 3,651 mm

Operating Weight 96 ton

Empty Weight 92 ton

Adhesion Weight 72 ton

Minimum Track Curvature 140 m

Pivot Distance 9.556 m

Drive Wheel Diameter 908.90 mm

Engine Type ALCO 244E

Engine Specifications 12 Cylinders Vee 4 Stroke Supercharged

Brake Horse Power 1,750 HP

Diesel to Generator Power 1,600 HP

Idle RPM 350

Max. RPM 1,100

Main Generator Model 5GT-581-A1

Traction Motor 6 Units, Type GE-761

Auxiliary Generator 2 Units, Model GY-27

Exciter 1 Unit, Type AM 808

Compressor Gardner Denver WCOV-9502

Maximum Tractive Effort (Adhesion) 15,120 kg

Maximum Speed 100 km/h

Minimum Continuous Speed 22 km/h

Fuel Capacity 1,900 lt

Lubricating Oil Capacity 750 lt

Cooling Water Capacity 900 lt

Sand Capacity 0.60 cu. m

Gear Ratio 92:19

Braking System Hand and air brake

9. Haulage Ropes

Jump to :-Round Strand 6 x 7 | Round Strand 6 x 19 | Flattened Stand (6x8 & 6x10) | Round Strand 6 x 7

Nominal rope diameter

Approximate nominal length mass

Minimum breaking force

Fibre centre

Steel centre

Rope grade 1770 Rope grade 1960

Fibre core

Steel core*

Fibre core

Steel core*

mm kg/100m kN

2 1.38 1.54 2.35 2.54 2.60 2.81

3 3.11 3.46 5.29 5.72 5.86 6.33

4 5.52 6.14 9.40 10.2 10.4 11.3

5 8.63 9.60 14.7 15.9 16.3 17.6

6 12.4 138. 21.2 22.9 23.4 25.3

7 16.9 18.8 28.8 31.1 31.9 34.5

8 22.1 24.6 37.6 40.7 41.6 45.0

9 27.9 31.1 47.6 51.5 52.7 57.0

10 34.5 38.4 58.8 63.5 65.1 70.4

11 41.7 46.5 71.1 76.9 78.7 85.1

12 49.7 55.3 84.6 91.5 93.7 101

13 58.3 64.9 99.3 107 110 119

14 67.6 75.3 115 125 128 138

16 88.3 98.3 150 163 167 180

18 112 124 190 206 211 228

20 138 154 235 254 260 281

22 167 186 284 308 315 341

24 199 221 338 366 375 405

26 233 260 397 430 440 476

28 270 301 461 498 510 552

32 353 393 602 651 666 721

36 447 498 762 824 843 912

40 552 614 940 1020 1040 1130

10. Belt Conveyor

TYPE OF BELT : · BELT STRENGTH IN KN/M. OF BELT WIDTH/NO. OF PLIES :1400/4,· THICKNESS OF TOP & BOTTOM RUBBER :5mm &2mm,· TOTAL THICKNESS :15.3mm,· OTHER DETAILS :FR GRADE, TYPE-III HEAVYDUTY, OPEN END, CUT

EDGE CONSTRUCTION, SKIM COATED PLIES, ALL NYLON,· BELT WIDTH :1400mm,

1. MATERIAL CODE NO. :55040425632. ELONGATION AT REFERENCE LOAD :3% Max.3. BREAK ELONGATION :10% Min.4. ADHESION PROPERTY(Min.) :

· TOP COVER TO PLY (IN KN/Mtr. OF WIDTH) :4.5,· PLY TO PLY (IN KN/Mtr. OF WIDTH) :5.25,· PLY TO BOTTOM COVER (IN KN/Mtr. OF WIDTH) :4.5,

5. COVER RUBBER PROPERTIES :· TENSILE STRENGTH :17MN/SQ.M (Min.)· ELONGATION AT BREAK :350%Min.

(CHANGE IN % AFTER AGEING FOR 72 Hrs. AT 70+1 0C)· TENSILE STRENGTH :+10%, -20% Max.· ELONGATION AT BREAK :+10%, -25% Max.· ABRASION LOSS (AS PER DIN-53516) :250 mm-cube Max.· TEAR RESISTANCE (AS PER DIN-53507) :SENSE- A : 20N/mm,

SENSE- B: 12N/mm,· SHORE HARDNESS :71 + / - 5 A,

7. TROUGHABILITY :AS PER IS –18918. FR GRADE TEST AS PER STANDARD :CAN/CSA - M422- M87, TYPE-C 10. LENGTH VARIATION :+2%, -0.5%11. LENGTH OF BELT IN ONE ROLL :200 Mtrs

11. Chain Comveyor

Detailed Product Description

Lumber Conveyor Chaim · Model umber:81X,81XH,81XHH,81XHS,500R,3939,Sharp top chains · Colors available:natural,yellow,blue,black · Lumber Conveyor Chaim's Specifications:

- Model number:81X,81XH,81XHH,81XHS,500R,3939,Sharp top chains- Colors available:natural,yellow,blue,black- Material:carbon steel

12. Fastback Horizontal Motion Conveyor (shaking conveyor,fast-back feeding conveyor, motion conveyor, packing machine)

 

Model: FM-3E3Place of Origin :China MainlandBrand :FOCUSCurrency :USDPrice Terms:FOBPackaging Details:Wooden caseMinimum Order:1 Maximum Supply:100Features Specifications:Fastback Horizontal Motion Conveyor(shaking conveyor,fast-back feeding conveyor,motion conveyor,packing machine) FM-3E3 Fastback Horizontal Motion Conveyor Application:Suitable for all kinds of dry snacks, granular and shaped products, such as potato chips/ crispsfrozen food;candies ,extruded foods ;peanuts and etc. Features:.1. The FBHMC eliminates product breakage and the loss of expensive seasonings &

coatings. and offers expanded benefits in a gentle product handling distribution system2. Very simplify installation and cleaning, The waterproof design for extreme environments

and wet cleaning also available.the stainless steel pan can easily take off. 3. The servo motor controlled system to provide high accuracy and stable speed according

to the production requirements. 4. The fully stainless steel structural framework enable a hygeian and strong support 5. The conveyors are delivered prewired and plumbed with all electrical mounted inside the

conveyor base for easy, ready-to-use installation.6. The conveyor have a wide variety of pan sizes and handles several heavier products, that

are customized to meet specific application requirements.  

Infeed pan length 2100mm(Optional:1800mm-3500mm)

Infeed pan width 410mm.

Infeed pan height 100mm.

Production capacity 10000Liters / H

International protection IP54

Machine Diamension 2100mm(L)*550mm(W)* 700mm (H)

Machine weight 250KG

Voltage AC220V Single phase;50Hz

Power 1.5KW

Major Products and Services:Manufacturing: mechanical and electrical products, packaging equipment, transmission equipment. Self-and agent all kinds of goods and technology import and export business (relating to permit the project to be operating with a valid license).

13. Shuttle Car ASC 18

The ASC18 is a shuttle car designed by VOEST-ALPINE Bergtechnik for the underground coal and soft rock mining industry, to operate behind any continuous mining machine . The ASC18 is electrically powered, equipped with variable frequency drive (AC) that provides infinitely variable speed for both traction and conveyor motors to shorten the driving cycles as well as discharge time of the conveyor. Optimum comfort and safety for operators are provided due to a new developed chassis frame suspension system and a cabin

conforming to the latest standards.

· Features and values· New developed chassis frame,

adjustable shock absorbers. · Variable frequency drive (VFD) High

constant torque from standstill. · Less motor maintenance needed in

comparison to standard DC-drives. (squirrel cage motor, no brushes)

· Infinitely variable transmission (IVT), soft start, easy manoeuvering.

· Conveyor motor driven by VFD. ( soft start and changeable speeds during loading / discharging), longer life time for the chain.

· Higher speed, better turning capability.

· Less operator fatigue because of smoother operation

· Newly designed tires with sufficient load capacity, side wall protection.

· Comfortable cut-off limit switch. (on board re-energizing)

· Key specifications

DimensionsTotal length

9,15 m (30 ft)

Total width 3,35 m (11 ft)Total height

1,98 m (78 ft)

CapacityPayload 18 t (39600 lbs)

Installed electric powerPower supply AC

480 V

Installed power

121 kW (165 HP

14. Drum hoist Knife disc diameter:1220mm Rotor Speed:740rpm Chip length:20-35mm

                    BX1112 Drum hoist 

 Specifica tions/Model

      BX1112

 Knife disc diameter   mm 

          1220

 Rotor Speed       rpm 

            740

 No.of knives     (pcs) 

             4

 Chip length         mm 

           20-35

 Type of feeding    

        Horizontal

 Feed opening dimension   mm 

          400×275

 Capacity    m3/h    

            15-20

 Power of main motor   kw 

              110

 Max.Log dimension   mm 

             100

 Type of discharge    

            Upper

 Total weight    kg 

           4585

 Overall dimension(L×W×H) mm 

3000×1570×1614

 Remarks 

    Right  feeding

15. Rope Drum Hoist

SpecificationsWinches upto 20 tons Cranes and hoists upto 100 tons Gates, embedded parts, penstocks and structures upto 20 ton weight The Hydro  mechanical division for Hydro power and Irrigation Project is our core strength and is backed by three decades of experience and success. Our expertise covers the entire gamut, from designing, detailed engineering, manufacturing, supplying, installation, testing & commissioning of complete range of Hydro-mechanical equipments.Well Equipped machine shop and the most talented manpower help us sustain high efficiency and service levels, and uncompromising quality at all times, Our repertoire of designing and production includes Vertical gates, Radial gates, Draft Tube gates, Intake gates, spillway and Stoplog gates, Hydraulic / Electrical Servo motor hoists, EOT and Gantry cranes, Trash racks and Trash rack cleaning machines and even building specified steel structures for bridges, towers and industries among others. In addition, we have key and critical state-of-the-art plants, tools and equipments, and manpower required to execute turnkey contracts for projects of any magnitude.· winches upto 20 tons · cranes and hoists upto 100 tons · gates, embedded parts, penstocks and structures upto 20 ton weight What sets us apart are focus, meticulous planning and the ability to perform beyond expectation even under the most challenging situations. It is an immense opportunity for us, to prove our expertise and to create history once again. Our gate to success lies in our constant bunger for taking challenges and excelling in it time and again.

16. AP SERIES SEWAGE AND WASTE WATER PUMPS

TECHNICAL SPECIFICATIONS :• Turbosan CAP series consists of centrifugal sewage and waste water pumps. They are used for pumping muddy liquids like sewage and other solid – water mixtures, with high viscosity.• For the vertical column pipe types 1500 m and 1000 mm long standard pipes used.Required length can be adjusted between 1000 mm and 8000 mm by using standard parts.• Axial trust force balanced by vanes located behind the impellers. In column pipe models trust force impeller and shaft weight balanced by oil or grease lubricated trust bearing fitted on base plate.• In dry installed models Teflon packing or mechanical seals suitable for pumped fluid can be used.• Pump impellers statically and dynamically balanced according to ISO 1940 class 6.3• Direction of rotation of the punps is clockwise seen from drive end..

• All pumps tested according to ISO 9906• CAP series pumps do not have suction ability, ther must be positive pressure on suction side.

  

General details:• Suction flange sizes:DN 50–DN 600• Discharge flange sizes:DN 50–DN 600• Capacity : 10 – 3000 m3/h• Discharge head : 5 – 60 m• Operating temperature:-10°C- +75°C  FLUID TYPES:• Unscreened sewage and other waste water types with high solids concentration Pumps are designed to tolerate large solids (Ø 30 Ø - 200 mm diameter) without clogging.• Water with sand content. Maximum grain size (20 - 30 mm). Liquid, sand ratio can be maximum % 6. For higher sand concentration preventive provisions must be taken aganist wear.• Maximum allowed fluid temperature is 40 °C• Maximum allowed medium density is 1,2 gr/cm3, maximum allowed medium viscosity is 1,5 x 10-6 m2/s. Measures must be taken to lower these values. PUMP IMPELLER TYPE  

FIELDS OF APPLICATIONS : • Domestic and industrial raw sewage water pumping

SB - SINGLE BLADE (NON - CLOG) IMPELLERSThese types of impellers are designed to handle large solids. They do not overload the motor at low heads.

DB - DOUBLE BLADE IMPELLERSThese types of impellers are usually used in large size pumps. Because of rotational symetry they operate in balance and vibration free. They can pass solids as wide as impeller channels.

V - VORTEX IMPELLERSThese types of impellers do not have closed channels. The impeller is placed behind the volute. Due to the rotation of the mass of fluid by the impeller, free vortex motion occurs, providing the  pumping effect. As a result of this special design they can easily pump long fibrous matter. 

• Waste water handling plants• Factory waste waters• Pumping of fluid with high viscosity and suspensions.• Pumping liquids in paint plants• Pumping industrial and chemical waste water.• Iron and steel industry• Paper pulp cellulose plants• Pumping of cooling water• Draining, deterring 

  PART MATERIALS

BRONZ FITTED CAST IRON

CasingCast iron(GJL 250) (EN-JL 1040)

Cast iron(GJL 250) (EN-JL 1040)

Impeller BronzeCast iron(GJL 250) (EN-JL 1040)

DiffusorCast iron(GJL 250) (EN-JL 1040)

Cast iron(GJL 250) (EN-JL 1040)

Wear ring BronzeCast iron(GJL 250) (EN-JL 1040)

ShaftStainless steel(AISI 420) (1.4021)

Carbon steel (1.0501)

Shaft sleeveStainless steel(AISI 420) (1.4021)

Stainless steel(AISI 420) (1.4021)

Column pipes(1.0120) welding construction

(1.0120) welding construction

NOTE: All pump components can be manufactured in different materials optionally according to the properties of the liquid to be pumped.