Made in the U.S.A.Meets the “Buy American” provisions of Section 1605 of the American Recovery and Reinvestment Act of 2009 (ARRA).
• 5 or 3 isolated 100 VA outputs
• On/Off circuit breaker switch for each output
• UL Listed Class 2
• Fully enclosed – perfect for central location
Perfect for VAV Applications: PSH500A and PSH300A
• High/low voltage separation
• 120Vac convenience outlets
= Class 2 (UL Approved UL5085-3) : UL916 Energy Management USA & Canada
107(800) 888-5538 | www.functionaldevices.com
PO
WE
RS
UP
PLI
ES
Shown Without
Cover
ShownWith
Cover
Notes: • To order without enclosure, see PSB40AB10 & PSB100AB10.• To order UL508, add “-IC” to end of model number.
Transformer:
Primary:Secondary:Frequency:
24 Vac ON/OFF:
One 40 VA Split-Bobbin, Inherently Limited (PSC40AB10)One 100 VA Split-Bobbin, Circuit Breaker (PSC100AB10)120 Vac24 Vac, w/ LED Indicator 50/60 HzOn / Off Switch & Breaker
PSC40AB10 Enclosed Single 40 VA Power Supply, 120 to 24 Vac
PSC100AB10 Enclosed Single 100 VA Power Supply, 120 to 24 Vac
Main Breaker ON/OFF:
Mounting:Temperature:
Approvals:
Dimensions:Weight:
Switch / Breaker (10 Amp)(Kills power to entire unit: Outlets, Aux. Output, & Transformer)*Total Combined Output 9AMounting plate included (as shown)40° CClass 2 (UL Approved UL5085-3), UL916, UL508 for -IC models, C-UL, CE, RoHS6.250˝ x 5.620˝ x 4.250˝4.40 lbs. (PSC40AB10), 5.80 lbs. (PSC100AB10)
3.900”5.620”
2.245”
5.620”
6.250”
4.500”
RemovableAccessPlate
RESET
OFF
ONOFF
Com 24 Vac
LEDIndicator
120 VacConvenience Outlet *
10 Amp Main Breaker/Switch24 Vac Breaker
120 Vac Aux. Output120 VacGroundNeutral
24 Vac On/O� Switch
* Move internal jumper to “HOT” position if you wish outlets to always be hot otherwise outlets will be switched by main breaker.
Made in USAMeets
“Buy American” of ARRA 2009
Class 2
Transformer:Over Current Protection:
Frequency:24 Vac ON/OFF:
Main Breaker ON/OFF:
Temperature:Approvals:
Dimensions:Weight:
One 40 VA Split-BobbinCircuit Breaker50/60 Hz On / Off Switch & BreakerSwitch / Breaker (10 Amp)(Kills power to entire unit: Outlets, Aux. Output, & Transformer)*Total Combined Output 9A40° C Class 2 (UL Approved UL5085-3), UL916, UL508 for -IC models, C-UL, CE, RoHS,^ Special Seismic Certification ofEquipment and Components: OSP-0201-104.500˝ x 5.438˝ x 4.500˝4.00 lbs.
Notes: • Output derating may exceed 20% due to elevated ambient temperature or heat buildup in device over time.• To order UL508, add “-IC” to end of model number.• Design is in accordance with ASCE 7-05 Chapter 13: ^ www.oshpd.ca.gov/FDD/Pre-Approval/ OSP-0201-10.pdf
PSH40A Series Enclosed Single 40 VA Power Supplies, 120 to 24 Vac
Notes: • Output derating may exceed 20% due to elevated ambient temperature or heat buildup in device over time.• Design is in accordance with ASCE 7-05 Chapter 13: ^ www.oshpd.ca.gov/FDD/Pre-Approval/ OSP-0201-10.pdf• All primary voltages other than 120 Vac will result in the disabling of convenience outlets.**
One 75 VA Split-BobbinCircuit Breaker50/60 Hz On / Off Switch & BreakerSwitch / Breaker (10 Amp)(Kills power to entire unit: Outlets, Aux. Output, & Transformer)*Total Combined Output 9AClass 2 (UL Approved UL5085-3), UL916, C-UL, CE, RoHS, Special ^ Seismic Certification of Equipment and Components: OSP-0201-104.500˝ x 5.438˝ x 4.500˝4.500 lbs.
Notes: • Output derating may exceed 20% due to elevated ambient temperature or heat buildup in device over time.• To order UL508, add “-IC” to end of model number.• Design is in accordance with ASCE 7-05 Chapter 13: ^ www.oshpd.ca.gov/FDD/Pre-Approval/ OSP-0201-10.pdf
One 100 VA Split-BobbinCircuit Breaker50/60 HzOn / Off Switch & BreakerSwitch / Breaker (10 Amp)(Kills power to entire unit: Outlets, Aux. Output, & Transformer)*Total Combined Output 9A 40° CClass 2 (UL Approved UL5085-3), UL916, UL508 for -IC models, C-UL, CE, RoHS, Spe-cial ^ Seismic Certification of Equipment and Components: OSP-0201-104.500˝ x 5.438˝ x 4.500˝4.600 lbs.
Output Wires: “B10˝ Models Only Auxiliary OutputBLU: 120 Vac
All Other ModelsPrimary WiresBLK: 120 VacWHT: Common
“W˝ Models OnlyTransformer OutputWHT/YEL: 24 VacWHT/BLU: Common
Outlet WiresBLK: 120 VacWHT: NeutralGRN: Ground
* Move internal jumper to “HOT” position if you wish outlets to always be hot otherwise outlets will be switched by main breaker.
* Move internal jumper to “HOT” position if you wish outlets to always be hot otherwise outlets will be switched by main breaker.
Made in USAMeets
“Buy American” of ARRA 2009
Class 2
Made in USAMeets
“Buy American” of ARRA 2009
Class 2
AC POWER SUPPLY
SPECIFICATIONS
AC POWER SUPPLY
SPECIFICATIONS
109(800) 888-5538 | www.functionaldevices.com
PO
WE
RS
UP
PLI
ES
Transformer:
Over Current Protection:Frequency:
24 Vac ON/OFF:Main Breaker ON/OFF:
Approvals:
Dimensions:Weight:
One 40 VA (PSH40AB10-EXT2) orOne 100 VA (PSH100AB10-EXT2)Circuit Breaker50/60 Hz On / Off Switch & BreakerSwitch / Breaker (10 Amp)(Kills power to entire unit: Outlets, Aux. Output, & Transformer)*Total Combined Output 9AClass 2 (UL Approved UL5085-3), UL916, C-UL, CE, RoHS4.500˝ x 5.438˝ x 4.500˝4.00 lbs.
Notes: • Output derating may exceed 20% due to elevated ambient temperature or heat buildup in device over time.
PSH40AB10-EXT2Enclosed Single 40 VA Power Supply, 120 to 24 Vac, with Three Foot Extension Cord
Notes: • All dual models: Model number denotes location of transformer within enclosure. PSH40A40A
Left side Right side• Output derating may exceed 20% due to elevated ambient temperature or heat buildup in device over time.• To order UL508, add “-IC” to end of model number.• Design is in accordance with ASCE 7-05 Chapter 13: ^ www.oshpd.ca.gov/FDD/Pre-Approval/ OSP-0201-10.pdf
Transformer:Over Current Protection:
Frequency:24 Vac ON/OFF:
Main Breaker ON/OFF:
Temperature:Approvals:
Dimensions:Weight:
Two 40 VA Split-BobbinCircuit Breaker50/60 HzOn / Off Switch & BreakerSwitch / Breaker (10 Amp)(Kills power to entire unit: Outlets, Aux. Output, & Transformer)*Total Combined Output 9A40° CClass 2 (UL Approved UL5085-3), UL916, UL508 for -IC models, C-UL, CE, RoHS, Spe-cial ^ Seismic Certification of Equipment and Components: OSP-0201-104.500˝ x 8.625˝ x 4.500˝5.400 lbs.
Notes: • All dual models: Model number denotes location of transformer within enclosure. PSH40A75A
Left side Right side• Output derating may exceed 20% due to elevated ambient temperature or heat buildup in device over time.• Design is in accordance with ASCE 7-05 Chapter 13: ^ www.oshpd.ca.gov/FDD/Pre-Approval/ OSP-0201-10.pdf• All primary voltages other than 120 Vac will result in the disabling of convenience outlets.**
Transformer:
Over Current Protection:Frequency:
24 Vac ON/OFF:Main Breaker ON/OFF:
Approvals:
Dimensions:Weight:
One 40 VA and One 75 VA Split-BobbinCircuit Breaker50/60 Hz On / Off Switch & Breaker Switch / Breaker (10 Amp)(Kills power to entire unit: Outlets, Aux. Output, & Transformer)*Total Combined Output 9AClass 2 (UL Approved UL5085-3), UL916, C-UL, CE, RoHS, Special ^ Seismic Certification of Equipment and Components: OSP-0201-104.500˝ x 8.625˝ x 4.500˝6.800 lbs.
Output Wires: “B10˝ Models Only Auxiliary OutputBLU: 120 Vac
All Other Models40 VA Primary WiresBLK: 120 VacWHT: Common 75 VA Primary Wires**GRY: 480 Vac BRN: 277 VacORG: 240 VacRED: 208 VacWHT: 120 VacBLK: Common
“W˝ Models OnlyTransformer OutputWHT/YEL: 24 VacWHT/BLU: Common
* Move internal jumper to “HOT” position if you wish outlets to always be hot otherwise outlets will be switched by main breaker.
Made in USAMeets
“Buy American” of ARRA 2009
Class 2
PSH40A100A Series Enclosed 40 VA and 100 VA Power Supplies, 120 to 24 Vac
RESET
OFF
ONOFF
ONOFF
120 Vac Convenience Outlet *
LED Indicator
24 VacOn/O� Switch
24 Vac Breaker
Com 24 VacCom 24 Vac
24 VacBreaker
120 Vac Convenience Outlet *10 Amp Main Breaker/Switch
Notes: • All dual models: Model number denotes location of transformer within enclosure. PSH40A100A
Left side Right side• Output derating may exceed 20% due to elevated ambient temperature or heat buildup in device over time.• To order UL508, add “-IC” to end of model number.• Design is in accordance with ASCE 7-05 Chapter 13: ^ www.oshpd.ca.gov/FDD/Pre-Approval/ OSP-0201-10.pdf
Transformer:
Over Current Protection:Frequency:
24 Vac ON/OFF:Main Breaker ON/OFF:
Temperature:Approvals:
Dimensions:Weight:
One 40 VA and One 100 VA Split-BobbinCircuit Breaker50/60 Hz On / Off Switch & BreakerSwitch / Breaker (10 Amp)(Kills power to entire unit: Outlets, Aux. Output, & Transformer)*Total Combined Output 9A40° CClass 2 (UL Approved UL5085-3), UL916, UL508 for -IC models, C-UL, CE, RoHS, Special ^ Seismic Certification of Equipment and Components: OSP-0201-104.500˝ x 8.625˝ x 4.500˝6.900 lbs.
Notes: • All dual models: Model number denotes location of transformer within enclosure. PSH75A75A
Left side Right side• Output derating may exceed 20% due to elevated ambient temperature or heat buildup in device over time.• Design is in accordance with ASCE 7-05 Chapter 13: ^ www.oshpd.ca.gov/FDD/Pre-Approval/ OSP-0201-10.pdf• All primary voltages other than 120 Vac will result in the disabling of convenience outlets.**
Transformer:Over Current Protection:
Frequency:24 Vac ON/OFF:
Main Breaker ON/OFF:
Approvals:
Dimensions:Weight:
Two 75 VA Split-BobbinCircuit Breaker50/60 Hz On / Off Switch & Breaker Switch / Breaker (10 Amp)(Kills power to entire unit: Outlets, Aux. Output, & Transformer)*Total Combined Output 9AClass 2 (UL Approved UL5085-3), UL916, C-UL, CE, RoHS, Special ^ Seismic Certification of Equipment and Components: OSP-0201-104.500˝ x 8.625˝ x 4.500˝8.400 lbs.
Notes: • All dual models: Model number denotes location of transformer within enclosure. PSH75A100A
Left side Right side• Output derating may exceed 20% due to elevated ambient temperature or heat buildup in device over time.• Design is in accordance with ASCE 7-05 Chapter 13: ^ www.oshpd.ca.gov/FDD/Pre-Approval/ OSP-0201-10.pdf• All primary voltages other than 120 Vac will result in the disabling of convenience outlets.**
Transformer:
Over Current Protection:Frequency:
24 Vac ON/OFF:Main Breaker ON/OFF:
Approvals:
Dimensions:Weight:
One 75 VA and One 100 VA Split-BobbinCircuit Breaker50/60 Hz On / Off Switch & BreakerSwitch / Breaker (10 Amp)(Kills power to entire unit: Outlets, Aux. Output, & Transformer)*Total Combined Output 9AClass 2 (UL Approved UL5085-3), UL916, C-UL, CE, RoHS, Special ^ Seismic Certification of Equipment and Components: OSP-0201-104.500˝ x 8.625˝ x 4.500˝8.500 lbs.
Output Wires: “B10˝ Models Only Auxiliary OutputBLU: 120 Vac
All Other Models75 VA Primary Wires**GRY: 480 Vac BRN: 277 VacORG: 240 VacRED: 208 VacWHT: 120 VacBLK: Common 100 VA Primary WiresBLK: 120 VacWHT: Common
“W˝ Models OnlyTransformer OutputWHT/YEL: 24 VacWHT/BLU: Common
* Move internal jumper to “HOT” position if you wish outlets to always be hot otherwise outlets will be switched by main breaker.
Made in USAMeets
“Buy American” of ARRA 2009
Class 2
SPECIFICATIONS
SPECIFICATIONS
AC POWER SUPPLY
AC POWER SUPPLY
PO
WE
RS
UP
PLI
ES
112 Functional Devices, Inc. | American Made. American Owned.
PSH100A100A Series Enclosed Dual 100 VA Power Supplies, 120 to 24 Vac
RESET
OFF
ONOFF
ONOFF
120 Vac Convenience Outlet *
LED Indicator
24 VacOn/O� Switch
24 Vac Breaker
Com 24 VacCom 24 Vac
24 VacBreaker
120 Vac Convenience Outlet *10 Amp Main Breaker/Switch
Notes: • All dual models: Model number denotes location of transformer within enclosure. PSH100A100A
Left side Right side• Output derating may exceed 20% due to elevated ambient temperature or heat buildup in device over time.• To order UL508, add “-IC” to end of model number.• Design is in accordance with ASCE 7-05 Chapter 13: ^ www.oshpd.ca.gov/FDD/Pre-Approval/ OSP-0201-10.pdf
Transformer:Over Current Protection:
Frequency:24 Vac ON/OFF:
Main Breaker ON/OFF:
Temperature:Approvals:
Dimensions:Weight:
Two 100 VA Split-BobbinCircuit Breaker50/60 Hz On / Off Switch & Breaker Switch / Breaker (10 Amp)(Kills power to entire unit: Outlets, Aux. Output, & Transformer)*Total Combined Output 9A40° CClass 2 (UL Approved UL5085-3), UL916, UL508 for -IC models, C-UL, CE, RoHS, Special ^ Seismic Certifica-tion of Equipment and Components: OSP-0201-104.500˝ x 8.625˝ x 4.500˝8.600 lbs.
Output Wires: “B10˝ Models Only Auxiliary OutputBLU: 120 Vac
All Other ModelsPrimary WiresBLK: 120 VacWHT: Common
“W˝ Models OnlyTransformer OutputWHT/YEL: 24 VacWHT/BLU: Common
* Move internal jumper to “HOT” position if you wish outlets to always be hot otherwise outlets will be switched by main breaker.
Made in USAMeets
“Buy American” of ARRA 2009
Class 2
Transformer:Primary:
Secondary:Frequency:
Overload Protection:Status:
ON/OFF Switch:Operating Temperature:
Humidity Range:Approvals:
Dimensions:Weight:
Housing:
One 40 VA120 Vac24 Vac, isolated50/60 HzInherently LimitedLED On = Activated2 Position-30 to 140° F5 to 95% (noncondensing)Class 2 (UL Approved UL5085-3), UL916, C-UL, CE, RoHS (PSMN40AS)UL916, C-UL, CE, RoHS (MH1000 Series)14.50˝ x 7.70˝ x 3.90˝ 7.28 lbs. NEMA 1 Metal Enclosure with screw cover
CTRL-PSKit Consisting of Model PSMN40AS and a Metal Enclosure
ShownWith
Cover
Notes: • Track mounted power supply may be ordered separately as model PSMN40AS.• 40 VA power supply mounted in MT212-4 track, high/low voltage barrier and 8.75˝ of 35 mm top hat DIN rail for mounting of desired controller in one metal enclosure.• Controller must be 9.50˝ x 6.75˝ x 3.50˝ or smaller with DIN rail mounting capability, or 9.50˝ x 6.75˝ x 3.125˝ without DIN rail mounting capability.• Controller not included.
Made in USAMeets
“Buy American” of ARRA 2009
ON
OFF
120 VacLine Input
24 VacDevice Output
14.5
0”
11.5
0”
14.5
0”
3.90”
7.70”5.70”
7.70”
SPECIFICATIONS
SPECIFICATIONS
GREAT FOR ZONE & NETWORK CONTROLLERS
AC POWER SUPPLY
AC POWER SUPPLY
113(800) 888-5538 | www.functionaldevices.com
PO
WE
RS
UP
PLI
ES
MHP3903100AB10 Enclosed Single100 VA Power Supply with Subpanel: Models MH3900 + SP3803S + PS100AB10
POWER SUPPLY (PS100AB10)
Notes: • Output derating may exceed 20% due to elevated ambient temperature or heat buildup in device over time.• Design is in accordance with ASCE 7-05 Chapter 13
Transformer:Over Current Protection:
Frequency:24 Vac ON/OFF:
Main Breaker ON/OFF:
Approvals:
Dimensions:Weight:
One 100 VA Split-BobbinCircuit Breaker50/60 Hz On / Off Switch & Breaker Switch / Breaker (10 Amp)(Kills power to entire unit: Outlets, Aux. Output, & Transformer)*Total Combined Output 9AClass 2 (UL Approved UL5085-3), UL916, C-UL, CE, RoHS4.500˝ x 8.625˝ x 4.500˝4.600 lbs.
Input Wires: Input Power WiresBLK: 120 VacWHT: NeutralGRN: Ground
Outlet WiresBLK: 120 VacWHT: NeutralGRN: Ground
Output Wires: Auxiliary OutputBLU: 120 Vac
Made in USAMeets
“Buy American” of ARRA 2009Class 2
METAL HOUSING (MH3900)
Construction:Cover Type:Approvals:
Dimensions:Weight:
14 Gauge SteelReversible Hook Hinge Key Latch DoorUL Listed, C-UL, CE Approved, RoHS12.50” (W) x 24.50” (H) x 6.50” (D)24.30 lbs.
POLYMETAL SUB-PANEL (SP3803S)
Mounting Area:Approvals:
Dimensions:Weight:
223.25˝ squarePlenum Rated19.00” x 11.75” 1.705 lbs.
6.50”
12.50”
10.60” 12.50”
24.5
0”
22.0
0”
11.7500”
9.00
00”
9.00
00”
19.0
000”
10.7500”
8.5000”
.5000”
.5000”
11.75”
10.75”
19.0
0”
9.00
”9.
00”
8.50”
0.50”
0.50”
RESET
OFF
ONOFF
4.500”
4.250”4.500”
5.438”5.150”
5.150”
5.15” 4.50”
4.50
”
5.15”
4.25
”
AC POWER SUPPLY
PERFORATED STEEL SUB-PANEL (SP3804S)
Mounting Area:Approvals:
Dimensions:Weight:
223.25˝ squarePlenum Rated19.00” x 11.75” 2.94 lbs.
MHP3904100AB10 Enclosed Single100 VA Power Supply with Subpanel: Models MH3900 + SP3804S + PS100AB10
SELECTION GUIDEModel # Sub-Panel
MHP3903100AB10 Polymetal
MHP3904100AB10 Perforated Steel
PO
WE
RS
UP
PLI
ES
114 Functional Devices, Inc. | American Made. American Owned.
MHP3903100A100AB10 Enclosed Dual 100 VA Power Supplies with Subpanel: Models MH3900 + SP3803S + PS100A100AB10
POWER SUPPLY (PS100A100AB10)
Notes: • Output derating may exceed 20% due to elevated ambient temperature or heat buildup in device over time.• Design is in accordance with ASCE 7-05 Chapter 13
Transformer:Over Current Protection:
Frequency:24 Vac ON/OFF:
Main Breaker ON/OFF:
Approvals:
Dimensions:Weight:
Two 100 VA Split-BobbinCircuit Breaker50/60 Hz On / Off Switch & Breaker Switch / Breaker (10 Amp)(Kills power to entire unit: Outlets, Aux. Output, & Transformer)*Total Combined Output 9AClass 2 (UL Approved UL5085-3), UL916, C-UL, CE, RoHS4.500˝ x 8.625˝ x 4.500˝7.000 lbs.
Input Wires: Input Power WiresBLK: 120 VacWHT: NeutralGRN: Ground
Outlet WiresBLK: 120 VacWHT: NeutralGRN: Ground
Output Wires: Auxiliary OutputBLU: 120 Vac
6.50”
12.50”
10.60” 12.50”
24.5
0”
22.0
0”11.7500”
9.00
00”
9.00
00”
19.0
000”
10.7500”
8.5000”
.5000”
.5000”
11.75”
10.75”
19.0
0”
9.00
”9.
00”
8.50”
0.50”
0.50”
RESET
OFF
ONOFF
ONOFF
8.625”
8.250”
8.250”
4.500”
4.50
0”4.
250”
8.25”
8.25”
4.25
”
4.50”
4.50
”
AC POWER SUPPLY
Made in USAMeets
“Buy American” of ARRA 2009Class 2
MHP3904100A100AB10 Enclosed Dual 100 VA Power Supplies with Subpanel: Models MH3900 + SP3804S + PS100A100AB10
SELECTION GUIDEModel # Sub-Panel
MHP3903100A100AB10 Polymetal
MHP3904100A100AB10 Perforated Steel
METAL HOUSING (MH3900)
Construction:Cover Type:Approvals:
Dimensions:Weight:
14 Gauge SteelReversible Hook Hinge Key Latch DoorUL Listed, C-UL, CE Approved, RoHS12.50” (W) x 24.50” (H) x 6.50” (D)24.30 lbs.
POLYMETAL SUB-PANEL (SP3803S)
Mounting Area:Approvals:
Dimensions:Weight:
223.25˝ squarePlenum Rated19.00” x 11.75” 1.705 lbs.
PERFORATED STEEL SUB-PANEL (SP3804S)
Mounting Area:Approvals:
Dimensions:Weight:
223.25˝ squarePlenum Rated19.00” x 11.75” 2.94 lbs.
115(800) 888-5538 | www.functionaldevices.com
PO
WE
RS
UP
PLI
ES
PSH500AShown
WithCover
PSH500AShown
WithoutCover
5 Secondaries: 24 Vac, with LED Indicators 4 Amp breaker for each output
Output:5 Ungrounded, Isolated, 100 VA, Class 2, 24 Vac Outputs. Terminals accept 12-26 AWG wire.
Ambient Temperature Derating:4A up to 40˚ C ; 3A up to 50˚ C ; 2A up to 55˚ C(When All 5 Outputs Operated Simultaneously)
Standby Wattage:48.515 W @ 120 Vac 48.699 W @ 240 Vac49.564 W @ 277 Vac48.255 W @ 480 Vac
Full Load Primary Current:4.66 A @ 120 Vac 2.41 A @ 240 Vac 2.06 A @ 277 Vac 1.17 A @ 480 Vac
Secondary Output Voltage vs. Load:24.0 V @ 1 Amp23.0 V @ 2 Amp21.8 V @ 3 Amp21.1 V @ 4 Amp
• With 240 Vac primary input voltage• When all 5 outputs operated simultaneously, at room temperature
Transformer:Over Current Protection:
Primary:Frequency:
Dimensions:
Approvals:
Sub-Panel:
Housing:Weight:
One (1) 500 VACircuit Breaker480/277/240/120 Vac50/60 Hz12.125˝ x 12.125˝ x 6.000˝ (PSH500A) 11.330˝ x 11.400˝ x 5.000˝ (PSMN500A)Class 2 (UL Approved UL5085-3), UL916, UL508, C-UL, CE, RoHS, Special ^ Seismic Certification of Equipment and Components: OSP-0201-10Plenum Rated Polymetal Sub-Panel (PSMN500A)NEMA1 Metal Enclosure (PSH500A)30.16 lbs. (PSH500A)20.60 lbs. (PSMN500A)
PSH500A Enclosed 500VA Power Supply with Five 100VA Class 2 Outputs, 480/277/240/120 Vac to 24 Vac
PSMN500A Open Style 500VA Power Supply with Five 100VA Class 2 Outputs, 480/277/240/120 Vac to 24 Vac
Notes: • To order UL508, add “-IC” to end of model number.• Open style (PSMN500A) is mounted to sub-panel SP3303 for shipping. Sub-panel may be removed to suit application.• Primary voltage terminal cover available. See model APS53-TC on page 141.• Design is in accordance with ASCE 7-05 Chapter 13: ^ www.oshpd.ca.gov/FDD/Pre-Approval/OSP-0201-10.pdf
PSMN500A
24VCOM
24VCOM
24VCOM
24VCOM
24VCOM
1
2
3
4
5
Indicator
BreakerU
ser C
onne
ctio
ns
Switch
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
480277240120COM
Made in USAMeets
“Buy American” of ARRA 2009
Class 2
SPECIFICATIONS
AC POWER SUPPLY
GREAT FOR VAV APPLICATIONS
PO
WE
RS
UP
PLI
ES
116 Functional Devices, Inc. | American Made. American Owned.
3 Secondaries: 24 Vac, with LED Indicators 4 Amp breaker for each output
Output:3 Ungrounded, Isolated, 100 VA, Class 2, 24 Vac Outputs. Terminals accept 12-26 AWG wire.
Standby Wattage:16.61 W @ 120 Vac 17.70 W @ 240 Vac16.26 W @ 277 Vac19.20 W @ 480 Vac
Full Load Primary Current:2.66 A @ 120 Vac 1.36 A @ 240 Vac 1.18 A @ 277 Vac 0.68 A @ 480 Vac
Secondary Output Voltage vs. Load:24.5 V @ 1 Amp23.5 V @ 2 Amp22.8 V @ 3 Amp22.3 V @ 4 Amp
• With 120 Vac primary input voltage• When all 3 outputs operated simultaneously, at room temperature
Transformer:Over Current Protection:
Primary:Frequency:
Dimensions:
Approvals:
Sub-Panel:
Housing:Weight:
One (1) 300 VACircuit Breaker480/277/240/120 Vac50/60 Hz12.125˝ x 12.125˝ x 6.000˝ (PSH300A)11.330˝ x 11.400˝ x 4.500˝ (PSMN300A)Class 2 (UL Approved UL5085-3), UL916, UL508, C-UL, CE, RoHS, Special ^ Seismic Certification of Equipment and Components: OSP-0201-10Plenum Rated Polymetal Sub-Panel (PSMN300A)NEMA1 Metal Enclosure (PSH300A)20.00 lbs. (PSH300A)11.00 lbs. (PSMN300A)
PSH300A Enclosed 300VA Power Supply with Three 100VA Class 2 Outputs, 480/277/240/120 Vac to 24 Vac
PSMN300A Open Style 300VA Power Supply with Three 100VA Class 2 Outputs, 480/277/240/120 Vac to 24 Vac
Notes: • To order UL508, add “-IC” to end of model number.• Open style (PSMN300A) is mounted to sub-panel SP3303 for shipping. Sub-panel may be removed to suit application.• Primary voltage terminal cover available. See model APS53-TC on page 141.• Design is in accordance with ASCE 7-05 Chapter 13: ^ www.oshpd.ca.gov/FDD/Pre-Approval/OSP-0201-10.pdf
1
2
3
ON
OFF
ON
OFF
ON
OFF
Indicator
Breaker
Switch
24VCOM
24VCOM
24VCOM
Use
r Con
nect
ions
480277240120COM
PSH300AShown
WithCover
PSH300AShown
WithoutCover
PSMN300A
Made in USAMeets
“Buy American” of ARRA 2009
Class 2
Ambient Temperature Derating:4A up to 40˚ C ; 3A up to 50˚ C ; 2A up to 55˚ C(When All 3 Outputs Operated Simultaneously)
Output:5 Ungrounded, Isolated, 40 VA, Class 2, 24 Vac Outputs. Terminals accept 12-26 AWG wire.
Ambient Temperature Derating:1.6A up to 40˚ C ; 1.2A up to 60˚ C(When All 5 Outputs Operated Simultaneously)
Transformer:Over Current Protection:
Primary:Frequency:
Dimensions:
Approvals:
Sub-Panel:
Housing:Weight:
One (1) 200 VACircuit Breaker480/347/277/240/120 Vac50/60 Hz12.125˝ x 12.125˝ x 6.000˝ (PSH200A) 11.330˝ x 11.400˝ x 5.000˝ (PSMN200A)Class 2 (UL Approved UL5085-3), UL916, C-UL, CE, RoHS Plenum Rated Polymetal Sub-Panel (PSMN200A)NEMA1 Metal Enclosure (PSH200A)18.60 lbs. (PSH200A)8.00 lbs. (PSMN200A)
PSH200A Enclosed 200VA Power Supply with Five 40VA Class 2 Outputs, 480/347/277/240/120 Vac to 24 Vac
PSMN200A Open Style 200VA Power Supply with Five 40VA Class 2 Outputs, 480/347/277/240/120 Vac to 24 Vac
Notes: • Open style (PSMN200A) is mounted to sub-panel SP3303 for shipping. Sub-panel may be removed to suit application.• Primary voltage terminal cover available. See model APS53-TC on page 141.
PSMN200A
24VCOM
24VCOM
24VCOM
24VCOM
24VCOM
1
2
3
4
5
Indicator
BreakerU
ser C
onne
ctio
ns
Switch
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
347480277240120COM Made in USA
Meets “Buy American”
of ARRA 2009
Class 2
Standby Wattage:18.93 W @ 120 Vac 22.08 W @ 240 Vac22.33 W @ 277 Vac23.11 W @ 347 Vac25.24 W @ 480 Vac
Full Load Primary Current:2.57 A @ 120 Vac 1.44 A @ 240 Vac1.17 A @ 277 Vac0.95 A @ 347 Vac0.73 A @ 480 Vac
Secondary Output Voltage vs. Load:24.9 V @ 0.5 Amp24.0 V @ 1.0 Amp23.9 V @ 1.4 Amp23.7 V @ 1.6 Amp
• With 120 Vac primary input voltage• When all 5 outputs operated simultaneously, at room temperature
SPECIFICATIONS
AC POWER SUPPLY
PERFECT FOR ISOLATING UP TO FIVE ZONE CONTROLLERS
347 VAC INPUT VOLTAGE PROVIDES DIRECT CONVERSION FROM MANY CANADIAN SYSTEMS TO CLASS 2 OUTPUTS
PO
WE
RS
UP
PLI
ES
118 Functional Devices, Inc. | American Made. American Owned.
PSH500A-LVCShown Without
High Voltage Cover & Low Voltage Access Plate
5 Secondaries: 24 Vac, with LED Indicators4 Amp breaker for each output
Output:5 Ungrounded, Isolated, 100 VA Class 2, 24 Vac Outputs. Removable Terminals accept16-22 AWG wire.
Ambient Temperature Derating:4A up to 40˚ C ; 3A up to 50˚ C ; 2A up to 55˚ C(When All 5 Outputs Operated Simultaneously)
Standby Wattage:48.515 W @ 120 Vac 48.699 W @ 240 Vac49.564 W @ 277 Vac48.255 W @ 480 Vac
Full Load Primary Current:4.66 A @ 120 Vac 2.41 A @ 240 Vac 2.06 A @ 277 Vac 1.17 A @ 480 Vac
Secondary Output Voltage vs. Load:24.0 V @ 1 Amp23.0 V @ 2 Amp21.8 V @ 3 Amp21.1 V @ 4 Amp
• With 240 Vac primary input voltage• When all 5 outputs operated simultaneously, at room temperature
Transformer:Over Current Protection:
Primary:Frequency:
Dimensions:Approvals:
Housing:
Weight:
One (1) 500 VACircuit Breaker480/277/240/120 Vac50/60 Hz12.125˝ x 12.125˝ x 6.000˝ Class 2 (UL Approved UL5085-3), UL916, C-UL, CE, RoHS NEMA1 Metal Enclosure with high/low separation32.30 lbs.
PSH500A-LVC Enclosed 500VA Power Supply, High/Low Voltage Separation with Five 100VA Class 2 Outputs, 480/277/240/120 Vac to 24 Vac
24VCOM
24VCOM
24VCOM
24VCOM
24VCOM
1
2
3
4
5
Indicator
Breaker
Use
r Con
nect
ions
Switch
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
480277240120COM
Made in USAMeets
“Buy American” of ARRA 2009
Class 2
PSH500A-LVCShown Without
Low Voltage Access Plate
PSH500A-LVCShown WithFull Cover & Access Plate
SPECIFICATIONS
AC POWER SUPPLY
119(800) 888-5538 | www.functionaldevices.com
PO
WE
RS
UP
PLI
ES
3 Secondaries: 24 Vac, with LED Indicators 4 Amp breaker for each output
Output:5 Ungrounded, Isolated, 40 VA, Class 2, 24 Vac Outputs. Terminals accept 12-26 AWG wire.
Ambient Temperature Derating:1.6A up to 40˚ C ; 1.2A up to 60˚ C(When All 5 Outputs Operated Simultaneously)
Transformer:Over Current Protection:
Primary:Frequency:
Dimensions:Approvals:
Housing:Weight:
One (1) 200 VACircuit Breaker480/347/277/240/120 Vac50/60 Hz12.125˝ x 12.125˝ x 6.000˝ Class 2 (UL Approved UL5085-3), UL916, C-UL, CE, RoHSNEMA1 Metal Enclosure20.30 lbs.
PSH200A-LVC Enclosed 200VA Power Supply with Five 40VA Class 2 Outputs, 480/347/277/240/120 Vac to 24 Vac
24VCOM
24VCOM
24VCOM
24VCOM
24VCOM
1
2
3
4
5
IndicatorBreaker
Use
r Con
nect
ions
Switch
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
347480277240120COM
Made in USAMeets
“Buy American” of ARRA 2009
Class 2
Standby Wattage:18.93 W @ 120 Vac 22.08 W @ 240 Vac22.33 W @ 277 Vac23.11 W @ 347 Vac25.24 W @ 480 Vac
Full Load Primary Current:2.57 A @ 120 Vac 1.44 A @ 240 Vac1.17 A @ 277 Vac0.95 A @ 347 Vac0.73 A @ 480 Vac
PSH200A-LVCShown Without
High Voltage Cover &
Low Voltage Access Plate
PSH200A-LVCShown Without
Low Voltage Access Plate
PSH200A-LVCShown WithFull Cover & Access Plate
Secondary Output Voltage vs. Load:24.9 V @ 0.5 Amp24.0 V @ 1.0 Amp23.9 V @ 1.4 Amp23.7 V @ 1.6 Amp
• With 120 Vac primary input voltage• When all 5 outputs operated simultaneously, at room temperature
SPECIFICATIONS
SPECIFICATIONS
AC POWER SUPPLY
AC POWER SUPPLY
PO
WE
RS
UP
PLI
ES
120 Functional Devices, Inc. | American Made. American Owned.
5 Secondaries: 24 Vac, with LED Indicators4 Amp breaker for each output
24 Vac ON/OFF:On / Off Switch & Breaker
Input:120 Vac Finger-Safe Terminals, 8-18 AWG
Output:5 Ungrounded, Isolated, 100 VA Class 2, 24 Vac Outputs. Removable Terminals accept16-22 AWG wire.
Ambient Temperature Derating:4A up to 40˚ C ; 3A up to 50˚ C ; 2A up to 55˚ C(When All 5 Outputs Operated Simultaneously)
Standby Wattage:48.515 W @ 120 Vac
Full Load Primary Current:4.66 A @ 120 Vac
Secondary Output Voltage vs. Load:24.0 V @ 1 Amp23.0 V @ 2 Amp21.8 V @ 3 Amp21.1 V @ 4 Amp
• When all 5 outputs operated simultaneously, at room temperature
Transformer:Over Current Protection:
Primary:Frequency:
Main Breaker ON/OFF:
Approvals:
Dimensions:Housing:
Weight:
One (1) 500 VACircuit Breaker120 Vac50/60 HzSwitch / Breaker (10 Amp) (Kills power to entire unit: 1 Outlet & Transformer)Class 2 (UL Approved UL5085-3), UL916, C-UL, CE, RoHS12.125˝ x 12.125˝ x 6.000˝ NEMA1 Metal Enclosure with high/low separation32.30 lbs.
PSH500AB10-LVC Enclosed 500VA Power Supply, High/Low Voltage Separation with Five 100VA Class 2 Outputs, 120 Vac to 24 Vac with 120 Vac Receptacle
Notes: • To order UL508, add “-IC” to end of model number.
Transformer:
Primary:Secondary:Frequency:
Over Current Protection:
24 Vac ON/OFF:Main Breaker ON/OFF:
One 40 VA Split-Bobbin (PSB40AB10)One 100 VA Split-Bobbin (PSB100AB10)120 Vac24 Vac, w/ LED Indicator50/60 HzInherently Limited + Circuit Breaker (PSB40AB10)Circuit Breaker (PSB100AB10)On / Off SwitchSwitch / Breaker (10 Amp)(Kills power to entire unit: Outlets, Aux. Output, & Transformer)*Total Combined Output 9A
PSB40AB10 Panel Mount 40 VA Power Supply, 120 to 24 Vac
PSB100AB10 Panel Mount 100 VA Power Supply, 120 to 24 Vac
Transformers:Primary:
Secondary:Frequency:
Overload Protection:Operating Temperature:
Humidity Range:Power Status:
Dimensions:
Track Mount:Weight:
ON/OFF Switch:Approvals:
One 40 VA120 Vac24 Vac, isolated50/60 HzInherently limited-30 to 140° F5 to 95% (noncondensing)LED On = Secondary Voltage Present2.500˝ x 2.750˝ x 4.000˝ (without track)2.800˝ x 2.750˝ x 4.000˝ (in track)MT212-4 Mounting Track Supplied1.60 lbs.2 Position (PSMN40AS)UL916, C-UL, CE, RoHS
PSMN40AS2.75˝ Track Mount 40 VA Power Supply, 120 Vac to 24 Vac, with Switch
LINE120 Vac
LOAD24 Vac
Switch:On / O�
PSMN40A2.75˝ Track Mount 40 VA Power Supply, 120 Vac to 24 Vac
LINE120 Vac
LOAD24 Vac
RESET
OFF
ONOFF
3.750”2.250” 2.250”
5.250”
5.200”4.610”RESET
OFF
ONOFF
Com 24 Vac
LEDIndicator
120 VacConvenience Outlet *
10 Amp Main Breaker/Switch24 Vac Breaker
120 Vac Aux. Output120 VacGroundNeutral
24 Vac On/O� Switch
Mounting:Temperature:
Approvals:
Dimensions:Weight:
Panel mount40° CClass 2 (UL Approved UL5085-3), UL916, UL508 for -IC models, C-UL, CE, RoHS5.200˝ x 5.250˝ x 3.750˝2.18 lbs. (PSB40AB10) 3.58 lbs. (PSB100AB10)
Made in USAMeets
“Buy American” of ARRA 2009
Class 2
Made in USAMeets
“Buy American” of ARRA 2009
Class 2
* Move internal jumper to “HOT” position if you wish outlets to always be hot otherwise outlets will be switched by main breaker.
SPECIFICATIONS
SPECIFICATIONS
REMOVABLE TERMINAL COVER PROVIDED
AC POWER SUPPLY: 120 VAC TO 24 VAC
AC POWER SUPPLY: 120 VAC TO 24 VAC
PO
WE
RS
UP
PLI
ES
124 Functional Devices, Inc. | American Made. American Owned.
Notes:• Requires a separate ungrounded transformer when used in conjunction with 1/2 wave rectified power supplies, grounded 24 Vac transformers, or when 24 Vac and 24 Vdc are connected in common.
VOLTAGE INPUT24 Vac
VOLTAGE OUTPUTFactory Set to 24 Vdc
Adjustable from 1.5-28 Vdc
+ Wht/Red
– Wht/Blu
Wht/Yel
Wht/Yel
Voltage Input:Voltage Output:
Frequency:Overload Protection:
Operating Temperature:Humidity Range:
Power Status:Dimensions:
Wires:Weight:
ON/OFF Switch:Approvals:
Housing Rating:
24 Vac, full-wave rectified1.5 - 28 Vdc non-isolated50/60 HzElectrical and Thermal, Auto-Reset-30 to 140° F5 to 95% (noncondensing)LED On = Activated2.30˝ x 3.20˝ x 1.80˝ with .50˝ NPT nipple16˝, 600V Rated.30 lbs.NoneClass 2 (UL Approved UL5085-3), UL916, C-UL, CE, RoHSUL Accepted for Use in Plenum, NEMA 1
Output Current Ratings: 116 mA @ 10 Vdc125 mA @ 12 Vdc300 mA @ 24 Vdc
Percent Ripple: 0.0016%, 24 Vdc @ 300 mA
PSP24DAEnclosed Non-Isolated Linear DC Power Supply, 24 Vac to 1.5-28 Vdc Adjustable Output
Input Current Rating: 550 mA Maximum
Regulation: Load: 0.04% No Load to Full LoadLine: 0.0125 V/V
Made in USAMeets
“Buy American” of ARRA 2009
Class 2
PSH24DWB10Enclosed Single Switching DC Power Supply 120 to 24 Vdc @ 2.5 Amp
Made in USAMeets
“Buy American” of ARRA 2009
Input Voltage:Frequency:DC Output:
Over Current Protection:Main Breaker ON/OFF:
Operating Temperature:Dimensions:
Weight:
120 Vac50/60 Hz24 Vdc @ 2.5 AmpCircuit BreakerSwitch / Breaker (10 Amp)(Kills power to entire unit)*Total Combined Output 9A32 to 122˚F4.500˝ x 5.438˝ x 4.500˝2.980 lbs.
Input Wires: Input Power WiresBLK: 120 VacWHT: NeutralGRN: Ground
Output Wires: DC Supply OutputWHT/RED: 24 VdcWHT/BLU: 24 Vdc COM Auxiliary OutputBLU: 120 Vac
120 VacConvenience Outlet *
RESET
OFF
120 Vac Convenience Outlet *
10 Amp Main Breaker/Switch
RESET
OFF
4.500”
4.250”4.500”
5.438”5.150”
5.150”
* Move internal jumper to “HOT” position if you wish outlets to always be hot otherwise outlets will be switched by main breaker.
Notes:• This device is not certified for use as a Class 2 power source.
SPECIFICATIONS
SPECIFICATIONS
DC POWER SUPPLY: 24 VAC TO 1.5 - 28 VDC
DC POWER SUPPLY: 120 VAC TO 24 VDC
125(800) 888-5538 | www.functionaldevices.com
PO
WE
RS
UP
PLI
ES
Notes:• Requires a separate ungrounded transformer when used in conjunction with 1/2 wave rectified power supplies, grounded 24 Vac transformers, or when 24 Vac and 24 Vdc are connected in common.
• See also supplementary model PSMN40AS
Voltage Input:Voltage Output:
Frequency: Overload Protection:
Operating Temperature:Humidity Range:
Power Status:Dimensions:
Track Mount:
Weight:ON/OFF Switch:
Approvals:
24 Vac, full-wave rectified1.5 - 28 Vdc non-isolated50/60 HzElectrical and Thermal, Auto-Reset-30 to 140° F5 to 95% (noncondensing)LED On = Activated1.500˝ x 2.750˝ x 1.750˝2.750˝MT212-2 Mounting Track Supplied0.20 lbs.None (PSMN24DA)2 Position Toggle (PSMN24DAS)Class 2 (UL Approved UL5085-3), UL916, C-UL, CE, RoHS
Output Current Ratings: 116 mA @ 10 Vdc125 mA @ 12 Vdc300 mA @ 24 Vdc
Percent Ripple: 0.0016%, 24 Vdc @ 300 mA
PSMN24DA2.75˝ Track Mount Non-Isolated Linear DC Power Supply, 24Vac to 1.5-28 Vdc, 300 mA Adjustable Output
Input Current Rating: 550 mA Maximum
Regulation: Load: 0.04% No Load to Full LoadLine: 0.0125 V/V
PSMN24DAS2.75˝ Track Mount Non-Isolated Linear DC Power Supply, 24Vac to 1.5-28 Vdc, 300 mA Adjustable Output, with Switch
Voltage Input24 Vac
Voltage OutputAdjustable1.5-28Vdc
+
–
Voltage Input24 Vac
Voltage OutputAdjustable1.5-28Vdc
+
–
Toggle Switch : On / O�
Made in USAMeets
“Buy American” of ARRA 2009
Class 2
PSH100A24DWB10Enclosed Power Supply, 100 VA (120 to 24 Vac) and Switching 120 to 24Vdc @ 2.5 Amp
Made in USAMeets
“Buy American” of ARRA 2009
Transformer:Voltage Input:
Frequency:Over Current Protection:
24 Vac ON/OFF:Main Breaker ON/OFF:
Dimensions:Weight:
One 100 VA Split-Bobbin120 Vac50/60 HzCircuit BreakerSwitch / Breaker (10 Amp)(Kills power to entire unit: Outlets, Aux. Output, & Transformer, and 24 Vdc)*Total Combined Output 9A4.500˝ x 8.625˝ x 4.500˝5.600 lbs.
Input Wires: Input Power WiresBLK: 120 VacWHT: NeutralGRN: Ground
Output Wires: DC Supply OutputWHT/RED: 24 VdcWHT/BLU: 24 Vdc COM
Auxiliary OutputBLU: 120 Vac
Transformer OutputWHT/YEL: 24 VacWHT/BLU: 24 Vac COM
RESET
OFF
ONOFF
120 Vac Convenience Outlet *
LED Indicator
24 VacBreaker
120 Vac Convenience Outlet *10 Amp Main Breaker/Switch
24 Vac On/O� Switch
RESET
OFF
ONOFF
8.625”
8.250”
8.250”
4.500”
4.50
0”4.
250”
* Move internal jumper to “HOT” position if you wish outlets to always be hot otherwise outlets will be switched by main breaker.
Notes:• This device is not certified for use as a Class 2 power source.
SPECIFICATIONS
SPECIFICATIONS
DC POWER SUPPLY: 24 VAC TO 1.5 - 28 VDC
AC & DC POWER SUPPLY: 120 VAC TO 24 VAC AND 24 VDC
PO
WE
RS
UP
PLI
ES
126 Functional Devices, Inc. | American Made. American Owned.
Voltage OutputAdjustable From
1.5-14 Vdc
Voltage Input24 Vac
+–
Switch:On / O�
Voltage Input:Voltage Output:
Frequency:Overload Protection:
Operating Temperature:Humidity Range:
Power Status:Dimensions:
Track Mount:
Weight:ON/OFF Switch:
Approvals:
24 Vac1.5 - 14 Vdc Isolated50/60 HzElectrical and Thermal, Auto-Reset-30 to 140° F5 to 95% (noncondensing)LED On = Activated1.625˝ x 2.750˝ x 4.000˝4.000˝ and 2.750˝MT212-4 Mounting Track Supplied1.10 lbs.2 PositionUL916, C-UL, CE, RoHS
Output Current Ratings: 300 mA @ 12 Vdc
Percent Ripple: 0.0016%, 12 Vdc @ 300 mA
PSM20A12DAS4.00˝ & 2.75˝ Track Mount Isolated Linear DC Power Supply, 24 Vac to 1.5-14Vdc, 300 mA Adjustable Output
Input Current Rating: 950 mA Maximum
Regulation: Load: 0.04% No Load to Full LoadLine: 0.0080 mV/V
VoltageInput
120 Vac
+–
VoltageOutput
AdjustableFrom
1.5-28 Vdc Switch:On / O�
VoltageInput24 Vac
+–
VoltageOutput
AdjustableFrom
1.5-28 Vdc Switch:On / O�
Voltage Input:
Voltage Output:Frequency:
Overload Protection:Operating Temperature:
Humidity Range: Power Status:
Dimensions:Track Mount:
Weight:ON/OFF Switch:
Approvals:
24 Vac (PSM24A24DAS)120 Vac (PSM19A24DAS)1.5 - 28 Vdc Isolated50/60 HzElectrical and Thermal, Auto-Reset-30 to 140° F5 to 95% (noncondensing)LED On = Activated1.625˝ x 2.750˝ x 4.000˝4.000˝ and 2.750˝MT212-4 Mounting Track Supplied1.10 lbs.2 PositionUL916, C-UL, CE, RoHS
Output Current Ratings: 116 mA @ 10 Vdc125 mA @ 12 Vdc300 mA @ 24 Vdc
Percent Ripple: 0.0016%, 24 Vdc @ 300 mA
PSM24A24DAS4.00˝ & 2.75˝ Track Mount Isolated Linear DC Power Supply, 24 Vac to 1.5-28 Vdc, 300 mA Adjustable Output
Input Current Rating: 950 mA Maximum (PSM24A24DAS)150 mA Maximum (PSM19A24DAS)
Regulation: Load: 0.04% No Load to Full LoadLine: 0.0080 mV/V (PSM24A24DAS)Line: 0.6250 mV/V (PSM19A24DAS)
PSM19A24DAS4.00˝ & 2.75˝ Track Mount Isolated Linear DC Power Supply, 120 Vac to 1.5-28 Vdc, 300 mA Adjustable Output
Made in USAMeets
“Buy American” of ARRA 2009
Class 2
Made in USAMeets
“Buy American” of ARRA 2009
Class 2
SPECIFICATIONS
SPECIFICATIONS
DC POWER SUPPLY: 24 VAC TO 1.5 - 14 VDC
DC POWER SUPPLY: 120 VAC OR 24 VAC TO 1.5 - 28 VDC
127(800) 888-5538 | www.functionaldevices.com
PO
WE
RS
UP
PLI
ES
VoltageInput
120 Vac
+ –VoltageOutput24 Vdc
Switch:On / O�
Voltage Input:Voltage Output:
Frequency:Overload Protection:
Operating Temperature:Humidity Range:
Power Status:Dimensions:
Track Mount:
Weight:ON/OFF Switch:
Approvals:
120 Vac24 Vdc Isolated50/60 HzElectrical and Thermal, Auto-Reset-30 to 140° F5 to 95% (noncondensing)LED On = Activated2.500˝ x 2.750˝ x 5.000˝ (without track)2.800” x 2.750” x 5.000” (in track)2.750˝MT212-6 Mounting Track Supplied1.50 lbs.2 PositionUL916, C-UL, CE, RoHS
Output Current Ratings: 1 A @ 24 Vdc
Percent Ripple: 0.0016%, 24 Vdc @ 1 A
PSMN40A24DS2.75˝ Track Mount Isolated Linear DC Power Supply, 120 Vac to 24 Vdc, 1 Amp
Input Current Rating: 400 mA Maximum
Regulation: Load: 0.50% No Load to Full LoadLine: 25.0000 mV/V
Made in USAMeets
“Buy American” of ARRA 2009
Class 2
SPECIFICATIONS
DC POWER SUPPLY: 120 VAC TO 24 VDC
PO
WE
RS
UP
PLI
ES
128 Functional Devices, Inc. | American Made. American Owned.
