Perkins Eastman Architects Partnership ADDENDUM PERKINS EASTMAN ARCHITECTS PARTNERSHIP THE PENNSYLVANIAN 1100 LIBERTY AVENUE PITTSBURGH, PA 15222 T. 412.456.0900 F. 412.456.0906 Date: November 30, 2017 Project Name: Baycrest Centre for Geriatric Care Wagman Centre Kitchen Renovation Subject: Tender & Permit Set - Addendum No. 004 From: Michael Clark (Perkins Eastman Architects Partnership) To: Penny Phelan (Baycrest) This Addendum, its items and attachments set forth herein shall act to qualify, clarify, or otherwise modify the previously issued “Tender and Permit” Drawing Set and Specifications dated November 9 th , 2017. These items, whether of omission, addition, substitution, or clarification, shall be included in the Tender pricing submitted by all bidders. Receipt of this document and its attachments must be acknowledged on the bid form. Failure to do so may subject the Bidder to disqualification. This Addendum consists of the following summary of changes: 1. Mechanical Addenda 00 91 13 M‐1 includes: a. Written changes that direct alterations to Mechanical drawings already issued as part of the Tender and Permit drawing set. b. The following sketches that direct alterations to Mechanical drawings already issued as part of the Tender and Permit drawing set. a. SK-M101.1 b. SK-M102.1 c. SK-M103.1 d. SK-M202.1 e. SK-M202.2 f. SK-M203.1 g. SK-M203.2 h. SK-M203.3 i. SK-M502.1 c. Reissued sheet M201, First Floor – HVAC Demo, Ground Floor – HVAC Demo & New d. Reissued sheet M301, First Floor – Fire Protection Demolition, Ground Floor – Fire protection 2. Electrical Addenda 00 91 13 E‐1 includes: a. Written changes that direct alterations to Mechanical drawings already issued as part of the Tender and Permit drawing set. b. Reissued sheet E203, Ground Floor – Electrical Plan 3. Architectural: a. Reissued sheet AD-151, Ground Floor – Partial Ceiling Demolition Plan End Addendum No. 004
Transcript
Perkins Eastman Architects Partnership
ADDENDUM
PERKINS EASTMAN ARCHITECTS PARTNERSHIP THE PENNSYLVANIAN 1100 LIBERTY AVENUE PITTSBURGH, PA 15222 T. 412.456.0900 F. 412.456.0906
Date: November 30, 2017
Project Name: Baycrest Centre for Geriatric Care Wagman Centre Kitchen Renovation
Subject: Tender & Permit Set - Addendum No. 004
From: Michael Clark (Perkins Eastman Architects Partnership)
To: Penny Phelan (Baycrest)
This Addendum, its items and attachments set forth herein shall act to qualify, clarify, or otherwise modify the previously issued “Tender and Permit” Drawing Set and Specifications dated November 9th, 2017. These items, whether of omission, addition, substitution, or clarification, shall be included in the Tender pricing submitted by all bidders. Receipt of this document and its attachments must be acknowledged on the bid form. Failure to do so may subject the Bidder to disqualification.
This Addendum consists of the following summary of changes:
1. Mechanical Addenda 00 91 13 M‐1 includes: a. Written changes that direct alterations to Mechanical drawings already issued as part of the Tender and
Permit drawing set. b. The following sketches that direct alterations to Mechanical drawings already issued as part of the
Tender and Permit drawing set. a. SK-M101.1 b. SK-M102.1 c. SK-M103.1 d. SK-M202.1 e. SK-M202.2 f. SK-M203.1 g. SK-M203.2 h. SK-M203.3 i. SK-M502.1
c. Reissued sheet M201, First Floor – HVAC Demo, Ground Floor – HVAC Demo & New d. Reissued sheet M301, First Floor – Fire Protection Demolition, Ground Floor – Fire protection
2. Electrical Addenda 00 91 13 E‐1 includes: a. Written changes that direct alterations to Mechanical drawings already issued as part of the Tender and
Permit drawing set. b. Reissued sheet E203, Ground Floor – Electrical Plan
3. Architectural: a. Reissued sheet AD-151, Ground Floor – Partial Ceiling Demolition Plan
End Addendum No. 004
Baycrest Centre for Geriatric Care Wagman Centre Main Kitchen HHA #2171127-01
Section 00 91 13 M-1 Addenda
Page 1 of 3
ADDENDA
00 91 13 M-1 The information listed below is to form part of the Contract Documents. All associated costs are to
be included in Tender Price shown on Tender Form. Acknowledgment of this Addendum, by number, to be shown in space provided on Tender Form.
.1 Refer to detail #1 (Ground Floor Plumbing Demolition). Revise note #1 to read “Remove existing grease trap and associated piping. Cap outlet pipe below floor”. Revise general notes and drawing notes as shown. Revise demolition of piping as shown to account for removal of Ground Floor kitchen equipment. Refer to sketch SK-M101.1 issued herewith.
1.3 Reference Drawing – M102 First & Ground Floor – Plumbing New Phase 1 (not re-issued)
.1 Refer to detail #1 (Ground Floor Plumbing New Phase 1). Revised location of the grease interceptor and associated piping and add new floor drain as shown. Added note #3. Revise existing piping as shown to account for removal of Ground Floor kitchen equipment. Refer to sketch SK-M102.1 issued herewith.
1.4 Reference Drawing – M103 First & Ground Floor – Plumbing New Phase 2 (not re-issued)
.1 Refer to detail #1 (Ground Floor Plumbing New Phase 2). Revised location of the grease interceptor and associated piping as shown. Removed drawings notes #3 and #4. Added drawing note #1. Revise existing piping as shown to account for removal of Ground Floor kitchen equipment. Refer to sketch SK-M103.1 issued herewith.
.2 Added detail #2 to show scope of demolition and new HVAC work on the ground floor.
.3 Refer to detail #1 (First Floor HVAC Demolition). Revised demolition to include removal of 10x6 exhaust duct dropping down to ground floor Project Kitchen. Revised note #5 to suit.
Baycrest Centre for Geriatric Care Wagman Centre Main Kitchen HHA #2171127-01
Section 00 91 13 M-1 Addenda
Page 2 of 3
1.6 Reference Drawing – M202 First Floor - HVAC New (not re-issued)
.1 Refer to detail #1 (First Floor HVAC New – Phase 1). Revised location of grease exhaust duct penetration up to mechanical room. Revised layout and size of grease exhaust duct within Phase 1 renovation area. Revised note #2 to correspond with revised 14” duct size. Revised phasing of EF-8 replacement and associated duct connections. Revised notes #3 and #9 accordingly. Removed note #11. Removed the reconnection of new exhaust ductwork to existing 10x4 duct down to ground floor project kitchen. Refer to sketch SK-M202.1 issued herewith.
.2 Refer to detail #2 (First Floor HVAC New – Phase 2). Revised size of grease exhaust duct within Phase 2 renovation area. Revised note #2 to correspond with revised 14” duct size. Revised phasing of EF-8 replacement and associated duct connections. Added notes #6, #7 and #8 accordingly. Revised location of dishwasher exhaust duct penetration up to penthouse. Refer to sketch SK-M202.2 issued herewith.
.1 Revised existing services shown to include, plenum access door, mechanical room exhaust fan EF-9 and relevant portion of heating and chilled water piping.
.2 Refer to detail #1 (Penthouse Mechanical Room – HVAC Demolition). Added relocation of EF-9 and demolition of section of sanitary exhaust duct to facilitate installation of new grease duct. Noted that EF-8 is to be removed during phase 2 of construction. Refer to sketch SK-M203.1 issued herewith.
.3 Refer to detail #2 (Penthouse Mechanical Room – HVAC New). Relocated EF-9 and added associated ductwork/connection to plenum. Added offset of 28x12 sanitary exhaust duct to facilitate installation of new grease exhaust duct. Revised location of grease exhaust duct penetration. Added note to provide new housekeeping pad for EF-8N. Added notes to provide spring isolated roof curb for MAU-1. Added note to use G20 ductwork on roof and flexible connection to MAU-1. Refer to sketch SK-M203.2 issued herewith.
.4 Refer to detail #2 (Penthouse Mechanical Room – HVAC New). Revised location of dishwasher exhaust duct penetration down to kitchen. Revised associated note to indicated running duct at high level within penthouse. Refer to sketch SK-M203.3 Issued herewith.
.1 Added grille type ‘R2’ with the following specifications:
.1 Application: Egg crate return or exhaust grille
.2 Selection MFG.: E.H. Price
.3 Manufacturer Data: 80DAL, 12x12, Aluminum construction
.4 Opposed Blade Damper: Yes
.5 Finish: By Owner
Baycrest Centre for Geriatric Care Wagman Centre Main Kitchen HHA #2171127-01
Section 00 91 13 M-1 Addenda
Page 3 of 3
.6 Remarks: Frame & border to suit application.
.2 Added register type ‘L’ with the following specifications:
.1 Application: Louvered face supply/return register
.2 Selection MFG.: E.H. Price
.3 Manufacturer Data: 620DAL, Size to suit ductwork, Aluminum construction c/w damper
.4 Opposed Blade Damper: Yes
.5 Finish: By Owner
.6 Remarks: Frame & border to suit application.
.3 Revised MAU-1 base type to D.
1.11 Reference Drawing – M502 Details II (not re-issued)
.1 Revised detail #2 to spring isolated roof curb for MAU-1. Refer to sketch SK-M502.1 issued herewith.
END OF ADDENDUM
EX CIRCUT04
EX CORRIDOR01
EX CORRIDOR010
EX PARTY017
EX MACHINE08
EX STORAGE07
EX DISHWASHING015
EX CHAIR STORAGE018 EX HOUSEKEEPING
09
EX PROJECT KITCHEN016
EX SERVERY014
EX CORRIDOR02
FOOD EQUIP
DISHWASHER
A18 A19 A20
B61
B58
B57
B56
B55
B59
D24
B62
B60
HHAngus & Associates Limited Consulting Engineers1127 Les l ie Street, Toronto, ON, M3C 2J6 Canadawww.hhangus.com | T 416 443 8200 | F 416 443 8290
AutoCAD SHX Text
3" CW (UP)
AutoCAD SHX Text
PHASE 1
AutoCAD SHX Text
PHASE 2
AutoCAD SHX Text
NG
AutoCAD SHX Text
NG
AutoCAD SHX Text
2" GAS (UP)
AutoCAD SHX Text
1
AutoCAD SHX Text
2
AutoCAD SHX Text
1
AutoCAD SHX Text
8"
AutoCAD SHX Text
1
AutoCAD SHX Text
1
AutoCAD SHX Text
3
AutoCAD SHX Text
3
AutoCAD SHX Text
7
AutoCAD SHX Text
3
AutoCAD SHX Text
EX. GREASE TRAP
AutoCAD SHX Text
EX. GREASE TRAP
AutoCAD SHX Text
1
AutoCAD SHX Text
3
AutoCAD SHX Text
8
AutoCAD SHX Text
5
AutoCAD SHX Text
4
AutoCAD SHX Text
6
AutoCAD SHX Text
6
AutoCAD SHX Text
4
AutoCAD SHX Text
GENERAL NOTES
AutoCAD SHX Text
THE EXISTING PLUMBING AND DRAINAGE SHOWN HAS BEEN TAKEN FROM ALL AVAILABLE INFORMATION AND SHALL BE ACCURATELY CHECKED ON SITE BY CONTRACTOR. CONTRACTOR IS RESPONSIBLE FOR COORDINATING THE DEMOLITION OF ANY PLUMBING SERVICES THAT CROSS BETWEEN PHASE 1 AND PHASE 2 OF THE RENOVATION AREA. PROVIDE TEMPORARY CAPS AS REQUIRED TO FACILITATE THIS WORK. REFER TO ARCHITECTURAL DRAWINGS FOR PHASING BOUNDARY. CONTRACTOR IS RESPONSIBLE FOR COORDINATING ALL DEMOLITION AND NEW WORK WITH EXISTING SERVICES LOCATED IN THE CEILING SPACE OF THE GROUND FLOOR TO FACILITATE THE WORK ABOVE. SEE ARCHITECTURAL DRAWING FOR REMOVAL OF FOOD SERVICE EQUIPMENT. REMOVE ANY WATER, DRAIN AND VENT CONNECTION AND CAP BACK TO MAIN.
AutoCAD SHX Text
DRAWING NOTES
AutoCAD SHX Text
REMOVE EXISTING GREASE TRAP AND ASSOCIATED PIPING. CAP OUTLET PIPE BELOW FLOOR. REMOVE THE DRAIN COBRA SYSTEM AND RETURN TO HOSPITAL REMOVE EXISTING SINK CAP HOT COLD AND VENT BACK TO MAIN. CAP DRAIN BELOW FLOOR AND PATCH TO MATCH EXISTING FLOOR. COLD WATER PIPING TO REMAIN UNTIL COMMENCEMENT OF PHASE 2 HOT WATER PIPING TO REMAIN UNTIL COMMENCEMENT OF PHASE 2 DEMO WATER AND ASSOCIATED PIPING TO DISHWASHER EXISTING SINK TO REMAIN COLD WATER PIPING TO REMAIN
AutoCAD SHX Text
1.
AutoCAD SHX Text
2.
AutoCAD SHX Text
1
AutoCAD SHX Text
2
AutoCAD SHX Text
PHASING LEGEND
AutoCAD SHX Text
DELINEATION BETWEEN PHASE 1 AND PHASE 2
AutoCAD SHX Text
3.
AutoCAD SHX Text
4.
AutoCAD SHX Text
3
AutoCAD SHX Text
4
AutoCAD SHX Text
5
AutoCAD SHX Text
6
AutoCAD SHX Text
7
AutoCAD SHX Text
8
AutoCAD SHX Text
1
AutoCAD SHX Text
THIS DRAWING IS TO BE READ IN CONJUNCTION WITH DRAWING
AutoCAD SHX Text
DRAWING
AutoCAD SHX Text
PROJECT:
AutoCAD SHX Text
TITLE:
AutoCAD SHX Text
SCALE:
AutoCAD SHX Text
DATE:
AutoCAD SHX Text
PROJECT No:
AutoCAD SHX Text
DRAWING No:
AutoCAD SHX Text
REV:
AutoCAD SHX Text
REVIEWED BY:
AutoCAD SHX Text
BAYCREST CENTER FOR GERIATRIC CARE
AutoCAD SHX Text
WAGMAN CENTRE MAIN KITCHEN
AutoCAD SHX Text
GROUND FLOOR - PLUMBING DEMOLITION
AutoCAD SHX Text
PLUMBING REVISIONS
AutoCAD SHX Text
1/8" = 1'
AutoCAD SHX Text
2017/11/27
AutoCAD SHX Text
2171127-01
AutoCAD SHX Text
SK-M101.1
AutoCAD SHX Text
M101.1
EX CIRCUT04
EX CORRIDOR01
EX CORRIDOR03
EX CORRIDOR010
EX PARTY017
EX MACHINE08
07
EX DISHWASHING015
EX CHAIR STORAGE018
EX HOUSEKEEPING09
EX PROJECT KITCHEN016
EX SERVERY014
EX CORRIDOR02
A18 A19 A20 A21
B61
B58
B57
B56
B55
B59
D24
B62
B60
HHAngus & Associates Limited Consulting Engineers1127 Les l ie Street, Toronto, ON, M3C 2J6 Canadawww.hhangus.com | T 416 443 8200 | F 416 443 8290
AutoCAD SHX Text
3" CW (UP)
AutoCAD SHX Text
1``
AutoCAD SHX Text
4``
AutoCAD SHX Text
2``
AutoCAD SHX Text
FS
AutoCAD SHX Text
FS
AutoCAD SHX Text
L
AutoCAD SHX Text
L
AutoCAD SHX Text
L
AutoCAD SHX Text
FS
AutoCAD SHX Text
~w"
AutoCAD SHX Text
1"
AutoCAD SHX Text
GD
AutoCAD SHX Text
1"
AutoCAD SHX Text
1~8"
AutoCAD SHX Text
1~4"
AutoCAD SHX Text
1"
AutoCAD SHX Text
~w"
AutoCAD SHX Text
~8"
AutoCAD SHX Text
1~8"
AutoCAD SHX Text
1~4"
AutoCAD SHX Text
1~8"
AutoCAD SHX Text
1~4"
AutoCAD SHX Text
1~4"
AutoCAD SHX Text
1"
AutoCAD SHX Text
1"
AutoCAD SHX Text
1"
AutoCAD SHX Text
4"
AutoCAD SHX Text
4"
AutoCAD SHX Text
~w"
AutoCAD SHX Text
~8"
AutoCAD SHX Text
1"
AutoCAD SHX Text
1~4"
AutoCAD SHX Text
1``
AutoCAD SHX Text
FS
AutoCAD SHX Text
1``
AutoCAD SHX Text
1``
AutoCAD SHX Text
~w"
AutoCAD SHX Text
~8"
AutoCAD SHX Text
~w"
AutoCAD SHX Text
~8"
AutoCAD SHX Text
~8"
AutoCAD SHX Text
~8"
AutoCAD SHX Text
~8"
AutoCAD SHX Text
~8"
AutoCAD SHX Text
~w"
AutoCAD SHX Text
1``
AutoCAD SHX Text
~8"
AutoCAD SHX Text
FD
AutoCAD SHX Text
CO
AutoCAD SHX Text
2"
AutoCAD SHX Text
2"
AutoCAD SHX Text
4"
AutoCAD SHX Text
4"
AutoCAD SHX Text
4"
AutoCAD SHX Text
2"
AutoCAD SHX Text
CO
AutoCAD SHX Text
4"
AutoCAD SHX Text
4"
AutoCAD SHX Text
4"
AutoCAD SHX Text
CO
AutoCAD SHX Text
4"
AutoCAD SHX Text
4"
AutoCAD SHX Text
CO
AutoCAD SHX Text
4"
AutoCAD SHX Text
SAN
AutoCAD SHX Text
SAN
AutoCAD SHX Text
SAN
AutoCAD SHX Text
SAN
AutoCAD SHX Text
1``
AutoCAD SHX Text
NG
AutoCAD SHX Text
NG
AutoCAD SHX Text
2" GAS (UP)
AutoCAD SHX Text
~8"
AutoCAD SHX Text
FD
AutoCAD SHX Text
FD
AutoCAD SHX Text
FD
AutoCAD SHX Text
S
AutoCAD SHX Text
INSTALL A VENTLESS GAS PRESSURE REGULATOR 2 PSI TO 7-11 INCHES W.C. EQUAL TO MAXITROL MODEL 325-3L c/w VLIMITER TO 2.5 FT PER HOUR FOR TEMPORARY INSTALLATION. INSTALL IN WELL VENTILATED SPACE. INSTALL BELOW CEILING.
AutoCAD SHX Text
AT THE TERRACE BUILDING GROUND FLOOR NORTH WEST CORNER IN MECHANICAL ROOM. REMOVE THE GAS PRV SO THAT THE LINE RUNNING TO THE KITCHEN WILL BE AT 2 PSI.
AutoCAD SHX Text
NG WILL NOW BE AT 2 PSI
AutoCAD SHX Text
2"
AutoCAD SHX Text
NG
AutoCAD SHX Text
2" 2 PSI NG (UP)
AutoCAD SHX Text
FFD
AutoCAD SHX Text
4"
AutoCAD SHX Text
FFD
AutoCAD SHX Text
CO
AutoCAD SHX Text
1
AutoCAD SHX Text
2
AutoCAD SHX Text
4" SANITARY BELOW SLAB
AutoCAD SHX Text
4"
AutoCAD SHX Text
PHASE 1
AutoCAD SHX Text
PHASE 2
AutoCAD SHX Text
CO
AutoCAD SHX Text
CO
AutoCAD SHX Text
SAN
AutoCAD SHX Text
4"
AutoCAD SHX Text
4"
AutoCAD SHX Text
CO
AutoCAD SHX Text
3
AutoCAD SHX Text
SAN
AutoCAD SHX Text
1
AutoCAD SHX Text
FD
AutoCAD SHX Text
4"
AutoCAD SHX Text
GENERAL NOTES
AutoCAD SHX Text
ALL SANITARY DRAINAGE TO BE A 1% SLOPE CONTRACTOR IS RESPONSIBLE FOR COORDINATING WORK ASSOCIATED WITH ANY PLUMBING SERVICES THAT CROSS BETWEEN PHASE 1 AND PHASE 2 OF THE RENOVATION AREA. PROVIDE TEMPORARY CAPS AS REQUIRED TO FACILITATE THIS WORK. REFER TO ARCHITECTURAL DRAWINGS FOR PHASING BOUNDARY. CONTRACTOR IS RESPONSIBLE FOR COORDINATING ALL DEMOLITION AND NEW WORK WITH EXISTING SERVICES LOCATED IN THE CEILING SPACE OF THE GROUND FLOOR TO FACILITATE THE WORK ABOVE.
AutoCAD SHX Text
1.
AutoCAD SHX Text
2.
AutoCAD SHX Text
DRAWING NOTES
AutoCAD SHX Text
GREASE TRAP EQUAL TO ZURN PROCEPTOR MODEL GMC 250. PLUMBING SERVICES TO SERVE THIS GREASE INTERCEPTOR SHALL BE PROVIDED DURING PHASE 1 OF CONSTRUCTION. COORDINATE WITH OWNER FOR ACCESS TO REQUIRED SPACES. DRAIN FROM GREASE TRAP TO RUN BELOW SLAB AND CONNECT TO EXISTING 4" DRAIN. EXACTED LOCATION BELOW SLAB TO BE DETERMINED ON SITE. CAP 4" DRAIN CONNECTION AT FLOOR FOR FUTURE CONNECTION TO NEW GREASE INTERCEPTOR
THIS DRAWING IS TO BE READ IN CONJUNCTION WITH DRAWING
AutoCAD SHX Text
DRAWING
AutoCAD SHX Text
PROJECT:
AutoCAD SHX Text
TITLE:
AutoCAD SHX Text
SCALE:
AutoCAD SHX Text
DATE:
AutoCAD SHX Text
PROJECT No:
AutoCAD SHX Text
DRAWING No:
AutoCAD SHX Text
REV:
AutoCAD SHX Text
REVIEWED BY:
AutoCAD SHX Text
BAYCREST CENTER FOR GERIATRIC CARE
AutoCAD SHX Text
WAGMAN CENTRE MAIN KITCHEN
AutoCAD SHX Text
GROUND FLOOR - PLUMBING NEW PHASE 1
AutoCAD SHX Text
PLUMBING REVISIONS
AutoCAD SHX Text
1/8" = 1'
AutoCAD SHX Text
2017/11/27
AutoCAD SHX Text
2171127-01
AutoCAD SHX Text
SK-M102.1
AutoCAD SHX Text
M102.1
EX CIRCUT04
EX CORRIDOR01
EX CORRIDOR03
EX CORRIDOR010
EX PARTY017
EX MACHINE08
EX DISHWASHING015
EX CHAIR STORAGE018 EX HOUSEKEEPING
09
EX PROJECT KITCHEN016
EX SERVERY014
EX CORRIDOR02
GREASE INTERCEPTOR05
A18 A19 A20 A21
B61
B58
B57
B56
B55
B59
D24
B62
B60
HHAngus & Associates Limited Consulting Engineers1127 Les l ie Street, Toronto, ON, M3C 2J6 Canadawww.hhangus.com | T 416 443 8200 | F 416 443 8290
AutoCAD SHX Text
3" CW (UP)
AutoCAD SHX Text
1"
AutoCAD SHX Text
1~8"
AutoCAD SHX Text
1~4"
AutoCAD SHX Text
1"
AutoCAD SHX Text
~w"
AutoCAD SHX Text
~8"
AutoCAD SHX Text
1~8"
AutoCAD SHX Text
1~4"
AutoCAD SHX Text
1~8"
AutoCAD SHX Text
1~4"
AutoCAD SHX Text
1~4"
AutoCAD SHX Text
1"
AutoCAD SHX Text
1"
AutoCAD SHX Text
1"
AutoCAD SHX Text
4"
AutoCAD SHX Text
4"
AutoCAD SHX Text
1"
AutoCAD SHX Text
1``
AutoCAD SHX Text
2``
AutoCAD SHX Text
FFD
AutoCAD SHX Text
FFD
AutoCAD SHX Text
FFD
AutoCAD SHX Text
L
AutoCAD SHX Text
L
AutoCAD SHX Text
L
AutoCAD SHX Text
FFD
AutoCAD SHX Text
~w"
AutoCAD SHX Text
1"
AutoCAD SHX Text
GD
AutoCAD SHX Text
~w"
AutoCAD SHX Text
~8"
AutoCAD SHX Text
1~4"
AutoCAD SHX Text
1``
AutoCAD SHX Text
FS
AutoCAD SHX Text
1``
AutoCAD SHX Text
1``
AutoCAD SHX Text
~w"
AutoCAD SHX Text
~8"
AutoCAD SHX Text
~w"
AutoCAD SHX Text
~8"
AutoCAD SHX Text
~8"
AutoCAD SHX Text
~8"
AutoCAD SHX Text
~8"
AutoCAD SHX Text
~w"
AutoCAD SHX Text
1``
AutoCAD SHX Text
FD
AutoCAD SHX Text
CO
AutoCAD SHX Text
2"
AutoCAD SHX Text
2"
AutoCAD SHX Text
4"
AutoCAD SHX Text
4"
AutoCAD SHX Text
4"
AutoCAD SHX Text
2"
AutoCAD SHX Text
CO
AutoCAD SHX Text
4"
AutoCAD SHX Text
4"
AutoCAD SHX Text
4"
AutoCAD SHX Text
CO
AutoCAD SHX Text
CO
AutoCAD SHX Text
4"
AutoCAD SHX Text
4"
AutoCAD SHX Text
4"
AutoCAD SHX Text
SAN
AutoCAD SHX Text
SAN
AutoCAD SHX Text
SAN
AutoCAD SHX Text
SAN
AutoCAD SHX Text
1``
AutoCAD SHX Text
NG
AutoCAD SHX Text
~8"
AutoCAD SHX Text
~8"
AutoCAD SHX Text
~8"
AutoCAD SHX Text
2"
AutoCAD SHX Text
NG
AutoCAD SHX Text
FS
AutoCAD SHX Text
FS
AutoCAD SHX Text
FFD
AutoCAD SHX Text
FD
AutoCAD SHX Text
FD
AutoCAD SHX Text
~8"
AutoCAD SHX Text
~8"
AutoCAD SHX Text
GD
AutoCAD SHX Text
S
AutoCAD SHX Text
4"
AutoCAD SHX Text
2"
AutoCAD SHX Text
FFD
AutoCAD SHX Text
FD
AutoCAD SHX Text
FD
AutoCAD SHX Text
FD
AutoCAD SHX Text
FD
AutoCAD SHX Text
4``
AutoCAD SHX Text
CO
AutoCAD SHX Text
~8"
AutoCAD SHX Text
L,EW
AutoCAD SHX Text
SAN
AutoCAD SHX Text
SAN
AutoCAD SHX Text
4"
AutoCAD SHX Text
4"
AutoCAD SHX Text
~8"
AutoCAD SHX Text
1"
AutoCAD SHX Text
INSTALL A VENT LESS GAS PRESSURE REGULATOR 2 PSI TO 7-11 INCHES W.C. EQUAL TO MAXITROL MODEL 325-7L FOR TEMPORARY INSTALLATION
AutoCAD SHX Text
2"
AutoCAD SHX Text
2" 2 PSI NG (UP)
AutoCAD SHX Text
NG
AutoCAD SHX Text
~w"
AutoCAD SHX Text
4"
AutoCAD SHX Text
4"
AutoCAD SHX Text
4"
AutoCAD SHX Text
4"
AutoCAD SHX Text
4"
AutoCAD SHX Text
4"
AutoCAD SHX Text
4"
AutoCAD SHX Text
4"
AutoCAD SHX Text
FD
AutoCAD SHX Text
~w"
AutoCAD SHX Text
4"
AutoCAD SHX Text
CO
AutoCAD SHX Text
S
AutoCAD SHX Text
2"
AutoCAD SHX Text
4"
AutoCAD SHX Text
SAN
AutoCAD SHX Text
1
AutoCAD SHX Text
CO
AutoCAD SHX Text
4"
AutoCAD SHX Text
~8"
AutoCAD SHX Text
CLOSE VALVES AND REMOVE VENTLESS GAS PRESSURE REGULATOR
AutoCAD SHX Text
CO
AutoCAD SHX Text
CO
AutoCAD SHX Text
CO
AutoCAD SHX Text
CO
AutoCAD SHX Text
SAN
AutoCAD SHX Text
4"
AutoCAD SHX Text
4"
AutoCAD SHX Text
CO
AutoCAD SHX Text
1
AutoCAD SHX Text
SAN
AutoCAD SHX Text
CO
AutoCAD SHX Text
SAN
AutoCAD SHX Text
4"
AutoCAD SHX Text
1
AutoCAD SHX Text
PHASE 1
AutoCAD SHX Text
PHASE 2
AutoCAD SHX Text
FD
AutoCAD SHX Text
GENERAL NOTES
AutoCAD SHX Text
ALL SANITARY DRAINAGE TO BE A 1% SLOPE CONTRACTOR IS RESPONSIBLE FOR COORDINATING WORK ASSOCIATED WITH ANY PLUMBING SERVICES THAT CROSS BETWEEN PHASE 1 AND PHASE 2 OF THE RENOVATION AREA. PROVIDE TEMPORARY CAPS AS REQUIRED TO FACILITATE THIS WORK. REFER TO ARCHITECTURAL DRAWINGS FOR PHASING BOUNDARY. CONTRACTOR IS RESPONSIBLE FOR COORDINATING ALL DEMOLITION AND NEW WORK WITH EXISTING SERVICES LOCATED IN THE CEILING SPACE OF THE GROUND FLOOR TO FACILITATE THE WORK ABOVE.
AutoCAD SHX Text
1.
AutoCAD SHX Text
2.
AutoCAD SHX Text
DRAWING NOTES
AutoCAD SHX Text
GREASE TRAP EQUAL TO ZURN PROCEPTOR MODEL GMC 50
AutoCAD SHX Text
1
AutoCAD SHX Text
GREASE INTERCEPTOR FOR DISHWASHER CALCULATIONS
AutoCAD SHX Text
EQUIPMENT
AutoCAD SHX Text
DESCRIPTION
AutoCAD SHX Text
SIZE
AutoCAD SHX Text
VOLUME CU N
AutoCAD SHX Text
#82
AutoCAD SHX Text
DISHWASHER
AutoCAD SHX Text
W/DRAIN TEMPERING
AutoCAD SHX Text
38GPM + (2GPM FOR DRAIN TEMPERING)
AutoCAD SHX Text
40 GPM
AutoCAD SHX Text
FLOW RATE TO GREASE INTERCEPTOR = 40 GPM
AutoCAD SHX Text
3.
AutoCAD SHX Text
1
AutoCAD SHX Text
PHASING LEGEND
AutoCAD SHX Text
DELINEATION BETWEEN PHASE 1 AND PHASE 2
AutoCAD SHX Text
1
AutoCAD SHX Text
THIS DRAWING IS TO BE READ IN CONJUNCTION WITH DRAWING
AutoCAD SHX Text
DRAWING
AutoCAD SHX Text
PROJECT:
AutoCAD SHX Text
TITLE:
AutoCAD SHX Text
SCALE:
AutoCAD SHX Text
DATE:
AutoCAD SHX Text
PROJECT No:
AutoCAD SHX Text
DRAWING No:
AutoCAD SHX Text
REV:
AutoCAD SHX Text
REVIEWED BY:
AutoCAD SHX Text
BAYCREST CENTER FOR GERIATRIC CARE
AutoCAD SHX Text
WAGMAN CENTRE MAIN KITCHEN
AutoCAD SHX Text
GROUND FLOOR - PLUMBING NEW PHASE 2
AutoCAD SHX Text
PLUMBING REVISIONS
AutoCAD SHX Text
1/8" = 1'
AutoCAD SHX Text
2017/11/27
AutoCAD SHX Text
2171127-01
AutoCAD SHX Text
SK-M103.1
AutoCAD SHX Text
103.1
D21
C9
A18 A19 A20 A21A17 A23
B61
B58
B57
B56
A16
A15
B55
A22
B59
A24
C10
C8
D24
B58
B59
B54 B54
A18 A19 A20 A21A17 A23A16 A24
D24
B57
B56
B55
B62
B60
A22A15
D21
C9
A18 A19 A20 A21A17 A23
B61
B58
B57
B56
A16
A15
B55
A22
B59
A24
C10
C8
D24
B58
B59
B54 B54
A18 A19 A20 A21A17 A23A16 A24
D24
B57
B56
B55
B62
B60
A22A15
EX WOMENSEX
EX MENSEX
EX CIRCUT04
EX CORRIDOR01
EX CORRIDOR03
EX TW CAFE013
EX CORRIDOR010
EX PARTY017
EX MACHINE08
EX CORRIDOR011
EX STORAGE07
EX DISHWASHING015
EX CHAIR STORAGE018
EX HOUSEKEEPING09
EX PROJECT KITCHEN016
EX SERVERY014
EX CORRIDOR02
EX RECEIVING06
EX VEST020
GREASE INTERCEPTOR05
FIRST FLOOR - HVAC
DEMO,
GROUND FLOOR -
HVAC DEMO & NEW
M201
1/8" = 1'
1100 Liberty Avenue
Pittsburgh, PA 15222
T. +1 412 456 0900
F. +1 412 456 0906
KEY PLAN
Owner:
Structural:
Mechanical, Electrical, & Plumbing:
Food Service:
Code Consultant:
SCALE:
DRAWING TITLE:
PROJECT TITLE:
PROJECT No:
BAYCREST HEALTH SCIENCES
55 AMEER AVENUE,
TORONTO, ONTARIO, MGA 2Z1
ENTUITIVE
200 UNIVERSITY AVENUE, 7TH FLOOR,
TORONTO, ONTARIO, M5H 3C6
FOOD FACILITIES CONCEPTS, INC.
1100 WASHINGTON AVE, SUITE 302
CARNEGIE, PA 15106
JENSEN HUGHES
2150 ISLINGTON AVE, SUITE 100
TORONTO, ONTARIO, M9P 3V4
BAYCREST CENTRE
FOR GERIATRIC CARE
55 AMEER AVENUE, TORONTO,
ONTARIO, MGA 2Z1
WAGMAN
CENTRE KITCHEN
RENOVATION
2171127-01
NOVEMBER 9, 2017
FOR TENDER AND PERMIT
SEAL
HHAngus & Associates Limited Consulting Engineers1127 Lesl ie Street, Toronto, ON, M3C 2J6 Canadawww.hhangus.com | T 416 443 8200 | F 416 443 8290
DATENO. ISSUE
AutoCAD SHX Text
62x20
AutoCAD SHX Text
54x24
AutoCAD SHX Text
48x16
AutoCAD SHX Text
D/F
AutoCAD SHX Text
D/F
AutoCAD SHX Text
D/F
AutoCAD SHX Text
D/F
AutoCAD SHX Text
D/F
AutoCAD SHX Text
10x6 DN
AutoCAD SHX Text
24x52
AutoCAD SHX Text
12x28
AutoCAD SHX Text
26x16
AutoCAD SHX Text
26x16
AutoCAD SHX Text
48x16
AutoCAD SHX Text
64x20
AutoCAD SHX Text
PHASE 1
AutoCAD SHX Text
PHASE 2
AutoCAD SHX Text
PHASE 1
AutoCAD SHX Text
PHASE 2
AutoCAD SHX Text
6x6
AutoCAD SHX Text
8x8
AutoCAD SHX Text
10x8
AutoCAD SHX Text
16x8
AutoCAD SHX Text
16x12
AutoCAD SHX Text
36x20 UP
AutoCAD SHX Text
36x20
AutoCAD SHX Text
36x18
AutoCAD SHX Text
20x10
AutoCAD SHX Text
14x10
AutoCAD SHX Text
18x10
AutoCAD SHX Text
3
AutoCAD SHX Text
1
AutoCAD SHX Text
2
AutoCAD SHX Text
T
AutoCAD SHX Text
CAP
AutoCAD SHX Text
4
AutoCAD SHX Text
4
AutoCAD SHX Text
5
AutoCAD SHX Text
EXISTING 10x6 DUCT DOWN TO GROUND FLOOR.
AutoCAD SHX Text
10x6
AutoCAD SHX Text
1
AutoCAD SHX Text
GENERAL NOTES
AutoCAD SHX Text
DEMOLITION DRAWINGS HAVE BEEN PREPARED AS A GENERAL GUIDE TO THE CONTRACTOR. NOT ALL SERVICES HAVE BEEN SHOWN. THE CONTRACTOR SHALL REMOVE ALL REDUNDANT SERVICES TO THE NEAREST ACTIVE SOURCE IN THE CONSTRUCTION AREA WHETHER THEY HAVE OR HAVE NOT BEEN SHOWN. NO EXTRA'S WILL BE ENTERTAINED FOR DEMOLITION.
AutoCAD SHX Text
2
AutoCAD SHX Text
1
AutoCAD SHX Text
REMOVE EXISTING TRANSFER FAN INCLUDING ASSOCIATED DUCTWORK, AIR REGISTERS AND DAMPERS. REMOVE ASSOCIATED CONTROLS AND ELECTRICAL WIRING.
AutoCAD SHX Text
DRAWING NOTES:
AutoCAD SHX Text
REMOVE EXISTING 36x20 EXHAUST DUCT ASSOCIATED WITH EXISTING EF-8. REFER TO DRAWING M203 FOR CONTINUATION.
AutoCAD SHX Text
3
AutoCAD SHX Text
EXISTING BLAST CHILLER TO BE RELOCATED AS PER ARCHITECTURAL DRAWINGS. REWORK EXISTING PIPING AND EXTEND WITH NEW PIPING TO CONNECT TO BLAST CHILLER AT NEW LOCATION. SIZE OF NEW PIPING TO BE ONE SIZE LARGER THAN EXISTING.
AutoCAD SHX Text
CONTRACTOR IS RESPONSIBLE FOR COORDINATING THE DEMOLITION OF ANY HVAC SERVICES THAT CROSS BETWEEN PHASE 1 AND PHASE 2 OF THE RENOVATION AREA. PROVIDE TEMPORARY CAPS AS REQUIRED TO FACILITATE THIS WORK. REFER TO ARCHITECTURAL DRAWINGS FOR PHASING BOUNDARY.
AutoCAD SHX Text
PHASING LEGEND
AutoCAD SHX Text
DELINEATION BETWEEN PHASE 1 AND PHASE 2
AutoCAD SHX Text
A
AutoCAD SHX Text
B
AutoCAD SHX Text
4
AutoCAD SHX Text
REMOVE EXISTING THERMOSTAT AND ASSOCIATED CONTROL WIRING. REMOVE ASSOCIATED REHEAT COIL AND CAP BRANCH PIPING.
AutoCAD SHX Text
5
AutoCAD SHX Text
REMOVE EXISTING 10x6 EXHAUST DUCTWORK DOWN TO GROUND FLOOR. REFER TO DRAWING M201.2 FOR CONTINUATION.
AutoCAD SHX Text
1
AutoCAD SHX Text
48x24
AutoCAD SHX Text
40x24
AutoCAD SHX Text
16x12
AutoCAD SHX Text
18x12
AutoCAD SHX Text
52x24
AutoCAD SHX Text
26x16
AutoCAD SHX Text
26x16
AutoCAD SHX Text
T
AutoCAD SHX Text
FD
AutoCAD SHX Text
FD
AutoCAD SHX Text
FD
AutoCAD SHX Text
FD
AutoCAD SHX Text
FD
AutoCAD SHX Text
FD
AutoCAD SHX Text
T
AutoCAD SHX Text
48x24
AutoCAD SHX Text
48x18
AutoCAD SHX Text
34x14
AutoCAD SHX Text
18x12
AutoCAD SHX Text
40x24
AutoCAD SHX Text
54x16
AutoCAD SHX Text
24x12
AutoCAD SHX Text
16x8
AutoCAD SHX Text
12x8
AutoCAD SHX Text
52x16
AutoCAD SHX Text
28x14
AutoCAD SHX Text
40x14
AutoCAD SHX Text
38x12
AutoCAD SHX Text
20x10
AutoCAD SHX Text
16x8
AutoCAD SHX Text
8x8
AutoCAD SHX Text
12x8
AutoCAD SHX Text
32x12
AutoCAD SHX Text
28x12
AutoCAD SHX Text
20x10
AutoCAD SHX Text
18x10
AutoCAD SHX Text
16x10
AutoCAD SHX Text
14x10
AutoCAD SHX Text
14x8
AutoCAD SHX Text
16x10
AutoCAD SHX Text
14x8
AutoCAD SHX Text
8x6
AutoCAD SHX Text
10x8
AutoCAD SHX Text
8x6
AutoCAD SHX Text
8x8
AutoCAD SHX Text
6x6
AutoCAD SHX Text
FD
AutoCAD SHX Text
48x14
AutoCAD SHX Text
10x8
AutoCAD SHX Text
46x14
AutoCAD SHX Text
14x12
AutoCAD SHX Text
18x12
AutoCAD SHX Text
14x8
AutoCAD SHX Text
FD
AutoCAD SHX Text
FD
AutoCAD SHX Text
FD
AutoCAD SHX Text
FD
AutoCAD SHX Text
26x14
AutoCAD SHX Text
FD
AutoCAD SHX Text
FD
AutoCAD SHX Text
FD
AutoCAD SHX Text
FD
AutoCAD SHX Text
FD
AutoCAD SHX Text
FD
AutoCAD SHX Text
34x12
AutoCAD SHX Text
16x12
AutoCAD SHX Text
6x5
AutoCAD SHX Text
24x12
AutoCAD SHX Text
10x6
AutoCAD SHX Text
20x12
AutoCAD SHX Text
36x12
AutoCAD SHX Text
30x12
AutoCAD SHX Text
14x18
AutoCAD SHX Text
FD
AutoCAD SHX Text
FD
AutoCAD SHX Text
FD
AutoCAD SHX Text
FD
AutoCAD SHX Text
26x16
AutoCAD SHX Text
36x12
AutoCAD SHX Text
20x12
AutoCAD SHX Text
16x8
AutoCAD SHX Text
14x8
AutoCAD SHX Text
12x8
AutoCAD SHX Text
200
AutoCAD SHX Text
(TYP. 9)
AutoCAD SHX Text
8x10
AutoCAD SHX Text
8x6
AutoCAD SHX Text
EX 12x12
AutoCAD SHX Text
(TYP. 3)
AutoCAD SHX Text
'L'
AutoCAD SHX Text
260
AutoCAD SHX Text
240
AutoCAD SHX Text
(TYP. 2)
AutoCAD SHX Text
240
AutoCAD SHX Text
EX 8"%%C
AutoCAD SHX Text
(TYP. 5)
AutoCAD SHX Text
EX 8"%%C
AutoCAD SHX Text
EX 8"%%C
AutoCAD SHX Text
EX 12x12
AutoCAD SHX Text
(TYP. 3)
AutoCAD SHX Text
400
AutoCAD SHX Text
'L'
AutoCAD SHX Text
1200
AutoCAD SHX Text
'L'
AutoCAD SHX Text
180
AutoCAD SHX Text
EX 14x12
AutoCAD SHX Text
400
AutoCAD SHX Text
400
AutoCAD SHX Text
EX 24x10
AutoCAD SHX Text
150
AutoCAD SHX Text
EX 6"%%C
AutoCAD SHX Text
(TYP. 3)
AutoCAD SHX Text
150
AutoCAD SHX Text
(TYP. 6)
AutoCAD SHX Text
EX 6"%%C
AutoCAD SHX Text
BD
AutoCAD SHX Text
BD
AutoCAD SHX Text
FD
AutoCAD SHX Text
10x6
AutoCAD SHX Text
10x6
AutoCAD SHX Text
8"%%C DOWN TO HOOD
AutoCAD SHX Text
FD
AutoCAD SHX Text
FD
AutoCAD SHX Text
16x10
AutoCAD SHX Text
34x14
AutoCAD SHX Text
38x14
AutoCAD SHX Text
44x14
AutoCAD SHX Text
14x8
AutoCAD SHX Text
8x8
AutoCAD SHX Text
10x6
AutoCAD SHX Text
12x10
AutoCAD SHX Text
34x12
AutoCAD SHX Text
10x6
AutoCAD SHX Text
EX 20x8
AutoCAD SHX Text
450
AutoCAD SHX Text
EX 24x6
AutoCAD SHX Text
450
AutoCAD SHX Text
EX 18x6
AutoCAD SHX Text
240
AutoCAD SHX Text
EX 14x6
AutoCAD SHX Text
240
AutoCAD SHX Text
EX 20x6
AutoCAD SHX Text
300
AutoCAD SHX Text
(TYP. 2)
AutoCAD SHX Text
EX 26X8
AutoCAD SHX Text
700
AutoCAD SHX Text
1
AutoCAD SHX Text
1
AutoCAD SHX Text
1
AutoCAD SHX Text
1
AutoCAD SHX Text
1
AutoCAD SHX Text
1
AutoCAD SHX Text
1
AutoCAD SHX Text
1
AutoCAD SHX Text
1
AutoCAD SHX Text
1
AutoCAD SHX Text
1
AutoCAD SHX Text
1
AutoCAD SHX Text
2
AutoCAD SHX Text
2
AutoCAD SHX Text
2
AutoCAD SHX Text
2
AutoCAD SHX Text
2
AutoCAD SHX Text
2
AutoCAD SHX Text
2
AutoCAD SHX Text
2
AutoCAD SHX Text
2
AutoCAD SHX Text
2
AutoCAD SHX Text
2
AutoCAD SHX Text
3
AutoCAD SHX Text
3
AutoCAD SHX Text
3
AutoCAD SHX Text
3
AutoCAD SHX Text
3
AutoCAD SHX Text
3
AutoCAD SHX Text
3
AutoCAD SHX Text
3
AutoCAD SHX Text
3
AutoCAD SHX Text
4
AutoCAD SHX Text
REMOVE EXISTING 10x6 HOOD EXHAUST DUCT UP. REFER TO DRAWING M201.1 FOR CONTINUATION.
AutoCAD SHX Text
1
AutoCAD SHX Text
3
AutoCAD SHX Text
3
AutoCAD SHX Text
3
AutoCAD SHX Text
3
AutoCAD SHX Text
3
AutoCAD SHX Text
3
AutoCAD SHX Text
3
AutoCAD SHX Text
EX 6x6
AutoCAD SHX Text
100
AutoCAD SHX Text
14x12
AutoCAD SHX Text
14x8
AutoCAD SHX Text
100
AutoCAD SHX Text
EX 6"%%C
AutoCAD SHX Text
2
AutoCAD SHX Text
2
AutoCAD SHX Text
3
AutoCAD SHX Text
EX 14x6
AutoCAD SHX Text
200
AutoCAD SHX Text
RR
AutoCAD SHX Text
150
AutoCAD SHX Text
EX 6"%%C
AutoCAD SHX Text
5
AutoCAD SHX Text
6x6
AutoCAD SHX Text
'R2' 12x12
AutoCAD SHX Text
110
AutoCAD SHX Text
6
AutoCAD SHX Text
6
AutoCAD SHX Text
6
AutoCAD SHX Text
6
AutoCAD SHX Text
'L'
AutoCAD SHX Text
100
AutoCAD SHX Text
1200
AutoCAD SHX Text
7
AutoCAD SHX Text
'L'
AutoCAD SHX Text
480
AutoCAD SHX Text
6
AutoCAD SHX Text
8x6
AutoCAD SHX Text
6
AutoCAD SHX Text
'L'
AutoCAD SHX Text
480
AutoCAD SHX Text
PROVIDE APPROPRIATE FIRE-STOPPING AND SEALING WHERE SERVICES PENETRATE FIRE RATED CEILING.
AutoCAD SHX Text
REMOVE AND REPLACE GRILLES/DIFFUSERS IN EX CORRIDOR 010 AS NECESSARY TO FACILITATE WORK IN CEILING FOR KITCHEN ABOVE. CONTRACTOR RESPONSIBLE FOR ANY DAMAGE.
AutoCAD SHX Text
NEW GREASE INTERCEPTOR ROOM. REFER TO ARCHITECTURAL PLANS FOR FURTHER INFORMATION.
AutoCAD SHX Text
GENERAL NOTES
AutoCAD SHX Text
DEMOLITION DRAWINGS HAVE BEEN PREPARED AS A GENERAL GUIDE TO THE CONTRACTOR. NOT ALL SERVICES HAVE BEEN SHOWN. THE CONTRACTOR SHALL REMOVE ALL REDUNDANT SERVICES TO THE NEAREST ACTIVE SOURCE IN THE CONSTRUCTION AREA WHETHER THEY HAVE OR HAVE NOT BEEN SHOWN. NO EXTRA'S WILL BE ENTERTAINED FOR DEMOLITION.
AutoCAD SHX Text
1
AutoCAD SHX Text
REMOVE EXISTING DIFFUSER/GRILLE.
AutoCAD SHX Text
DRAWING NOTES:
AutoCAD SHX Text
A
AutoCAD SHX Text
2
AutoCAD SHX Text
REMOVE AND REPLACE EXISTING DIFFUSER/GRILLE AS NECESSARY TO FACILITATE WORK ABOVE CEILING LEVEL. CONTRACTOR RESPONSIBLE FOR ANY DAMAGE.
AutoCAD SHX Text
3
AutoCAD SHX Text
EXISTING DIFFUSER/GRILLE TO REMAIN. CONTRACTOR RESPONSIBLE FOR ANY DAMAGE.
AutoCAD SHX Text
4
AutoCAD SHX Text
REMOVE EXISTING EXHAUST DUCTWORK CONNECTED TO KITCHEN HOOD. REMOVE ASSOCIATED DUCTWORK AS SHOWN.
AutoCAD SHX Text
5
AutoCAD SHX Text
REMOVE AND RELOCATE EXISTING DIFFUSER TO FACILITATE INSTALLATION OF NEW GREASE INTERCEPTOR ROOM. RE-BALANCE TO AIRFLOW SHOWN.
AutoCAD SHX Text
6
AutoCAD SHX Text
PROVIDE DUCT-MOUNTED TYPE 'L' SUPPLY/RETURN REGISTER SIZED TO SUIT DUCTWORK. BALANCE TO AIRFLOW SHOWN. REFER TO DRAWING M401 FOR FURTHER INFORMATION.
AutoCAD SHX Text
7
AutoCAD SHX Text
RE-BALANCE EXISTING RETURN/SUPPLY TO AIRFLOW SHOWN.
AutoCAD SHX Text
COORDINATE LOCATION OF ANY NEW GRILLES/DIFFUERS WITH ARCHITECTURAL PLANS.
AutoCAD SHX Text
B
AutoCAD SHX Text
ALL AIRFLOWS NOTED ARE IN CFM UNLESS OTHERWISE SPECIFIED.
AutoCAD SHX Text
C
AutoCAD SHX Text
1
AutoCAD SHX Text
M201
AutoCAD SHX Text
FIRST FLOOR HVAC DEMOLITION
AutoCAD SHX Text
1/8" = 1'
AutoCAD SHX Text
2
AutoCAD SHX Text
M201
AutoCAD SHX Text
GROUND FLOOR HVAC DEMOLITION & NEW
AutoCAD SHX Text
1/8" = 1'
AutoCAD SHX Text
1
AutoCAD SHX Text
1. 11/27/2017 ISSUED FOR ADD. M-1
AutoCAD SHX Text
1
EX REF
EX REF
EX FREEZER
MEAT SCULLERY108
MEAT PREP107
A18 A19 A20
B58
B57
B56
B55
D24
HHAngus & Associates Limited Consulting Engineers1127 Lesl ie Street , Toronto, ON, M3C 2J6 Canadawww.hhangus.com | T 416 443 8200 | F 416 443 8290
AutoCAD SHX Text
144 CFM
AutoCAD SHX Text
20%%C
AutoCAD SHX Text
14%%C
AutoCAD SHX Text
12x12
AutoCAD SHX Text
4
AutoCAD SHX Text
1
AutoCAD SHX Text
1
AutoCAD SHX Text
2
AutoCAD SHX Text
2
AutoCAD SHX Text
20x20
AutoCAD SHX Text
3
AutoCAD SHX Text
6
AutoCAD SHX Text
6
AutoCAD SHX Text
8
AutoCAD SHX Text
10
AutoCAD SHX Text
9
AutoCAD SHX Text
S
AutoCAD SHX Text
20x12
AutoCAD SHX Text
20%%C
AutoCAD SHX Text
30%%C
AutoCAD SHX Text
14%%C
AutoCAD SHX Text
1
AutoCAD SHX Text
1
AutoCAD SHX Text
EXISTING EXHAUST DUCTWORK SERVING PHASE 2 OF KITCHEN DURING PHASE 1 OF CONSTRUCTION.
AutoCAD SHX Text
1
AutoCAD SHX Text
3
AutoCAD SHX Text
TEMPORARILY CONNECT NEW 20x20 DUCT TO EXISTING 36x20 DUCT UP TO EXISTING EF-8 LOCATED EF-8 LOCATED LOCATED IN PENTHOUSE MECHANICAL ROOM. CONTRACTOR TO COORDINATE WORK THAT OCCURS WITHIN THE PHASE 2 BOUNDARY WITH OWNER TO ENSURE NO INTERRUPTIONS TO KITCHEN STAFF.
AutoCAD SHX Text
EXISTING BLAST CHILLER RELOCATED AS PER ARCHITECTURAL DRAWINGS. REWORK EXISTING PIPING AND EXTEND WITH NEW PIPING TO CONNECT TO BLAST CHILLER AT NEW LOCATION. SIZE OF NEW PIPING TO BE ONE SIZE LARGER THAN EXISTING.
AutoCAD SHX Text
4
AutoCAD SHX Text
DRAWING NOTES:
AutoCAD SHX Text
CAP DUCTWORK FOR PHASE 2 CONSTRUCTION.
AutoCAD SHX Text
6
AutoCAD SHX Text
8
AutoCAD SHX Text
30" GREASE EXHAUST DUCTWORK UP TO EF-1. REFER TO DRAWING M203 AND M204 FOR REFER TO DRAWING M203 AND M204 FOR CONTINUATION.
AutoCAD SHX Text
9
AutoCAD SHX Text
EXISTING 36x20 EXHAUST DUCT UP TO EXISTING EF-8. EXISTING EF-8 IS TO BE REMOVED AND EF-8. EXISTING EF-8 IS TO BE REMOVED AND . EXISTING EF-8 IS TO BE REMOVED AND EF-8 IS TO BE REMOVED AND IS TO BE REMOVED AND REPLACED BY EF-8N DURING PHASE 2 OF CONSTRUCTION. REFER TO M202.2 FOR FURTHER EF-8N DURING PHASE 2 OF CONSTRUCTION. REFER TO M202.2 FOR FURTHER DURING PHASE 2 OF CONSTRUCTION. REFER TO M202.2 FOR FURTHER INFORMATION.
AutoCAD SHX Text
10
AutoCAD SHX Text
GREASE DUCT FROM KITCHEN HOOD CONNECTOR TO EXHAUST FAN EF-1 INLET SHALL BE PROTECTED EF-1 INLET SHALL BE PROTECTED INLET SHALL BE PROTECTED GREASE DUCT WITH INTEGRAL CHASE. REFER TO SPEC 23 31 21 FOR FURTHER REQUIREMENTS.
AutoCAD SHX Text
2
AutoCAD SHX Text
CONNECT 14 DUCT DOWN TO KITCHEN HOOD EXHAUST DUCT COLLAR. BALANCE AIRFLOW AT EACHCONNECTION TO 1829 CFM.
AutoCAD SHX Text
1
AutoCAD SHX Text
CONNECT 24x12 DUCT DOWN TO KITCHEN HOOD SUPPLY DUCT COLLAR. BALANCE AIRFLOW FOR EACH CONNECTION TO 1463 CFM.
AutoCAD SHX Text
1
AutoCAD SHX Text
1
AutoCAD SHX Text
THIS DRAWING IS TO BE READ IN CONJUNCTION WITH DRAWING
AutoCAD SHX Text
DRAWING
AutoCAD SHX Text
PROJECT:
AutoCAD SHX Text
TITLE:
AutoCAD SHX Text
SCALE:
AutoCAD SHX Text
DATE:
AutoCAD SHX Text
PROJECT No:
AutoCAD SHX Text
DRAWING No:
AutoCAD SHX Text
REV:
AutoCAD SHX Text
REVIEWED BY:
AutoCAD SHX Text
BAYCREST CENTER FOR GERIATRIC CARE
AutoCAD SHX Text
WAGMAN CENTRE MAIN KITCHEN
AutoCAD SHX Text
FIRST FLOOR - HVAC NEW PHASE 1
AutoCAD SHX Text
EXHAUST REVISIONS
AutoCAD SHX Text
1/8" = 1'
AutoCAD SHX Text
2017/11/27
AutoCAD SHX Text
2171127-01
AutoCAD SHX Text
SK-M202.1
AutoCAD SHX Text
M202.1
DAIRY COOKING116
MEAT DISH STOR113
EX REFEX REF
EX FREEZER
EX ELEV 5
DISHWASH115
DAIRY DISH STOR114
SEVER PICKUP - DAIRY
117
DAIRY PREP109 VEGETABLE PREP
111
DAIRY SCULLERY110
CORR118
B58
B57
B56
B59
D24
B60
B58
B57
B56
B59
D24
B60
A22A19 A20 A21 A22A19 A20 A21
HHAngus & Associates Limited Consulting Engineers1127 Les l ie Street, Toronto, ON, M3C 2J6 Canadawww.hhangus.com | T 416 443 8200 | F 416 443 8290
AutoCAD SHX Text
PHASE 2
AutoCAD SHX Text
24x52
AutoCAD SHX Text
12x28
AutoCAD SHX Text
26x16
AutoCAD SHX Text
26x16
AutoCAD SHX Text
64x20
AutoCAD SHX Text
62x20
AutoCAD SHX Text
54x24
AutoCAD SHX Text
12x8
AutoCAD SHX Text
14x12
AutoCAD SHX Text
14x12
AutoCAD SHX Text
12x12
AutoCAD SHX Text
12x12
AutoCAD SHX Text
48x16
AutoCAD SHX Text
144 CFM
AutoCAD SHX Text
144 CFM
AutoCAD SHX Text
144 CFM
AutoCAD SHX Text
144 CFM
AutoCAD SHX Text
144 CFM
AutoCAD SHX Text
144 CFM
AutoCAD SHX Text
144 CFM
AutoCAD SHX Text
144 CFM
AutoCAD SHX Text
144 CFM
AutoCAD SHX Text
20%%C
AutoCAD SHX Text
14%%C
AutoCAD SHX Text
24x12
AutoCAD SHX Text
20x12
AutoCAD SHX Text
14%%C
AutoCAD SHX Text
1
AutoCAD SHX Text
PHASE 1
AutoCAD SHX Text
3
AutoCAD SHX Text
2
AutoCAD SHX Text
2
AutoCAD SHX Text
5
AutoCAD SHX Text
12x12
AutoCAD SHX Text
S
AutoCAD SHX Text
S
AutoCAD SHX Text
S
AutoCAD SHX Text
S
AutoCAD SHX Text
S
AutoCAD SHX Text
S
AutoCAD SHX Text
S
AutoCAD SHX Text
S
AutoCAD SHX Text
S
AutoCAD SHX Text
FD
AutoCAD SHX Text
14%%C
AutoCAD SHX Text
1
AutoCAD SHX Text
1
AutoCAD SHX Text
1
AutoCAD SHX Text
36x20
AutoCAD SHX Text
36x20 UP TO EF-8N. EF-8N. . PROVIDE FIRE DAMPER AT FLOOR PENETRATION.
AutoCAD SHX Text
FD
AutoCAD SHX Text
6
AutoCAD SHX Text
7
AutoCAD SHX Text
8
AutoCAD SHX Text
1
AutoCAD SHX Text
GENERAL NOTES
AutoCAD SHX Text
3
AutoCAD SHX Text
CONNECT 12x12 STAINLESS STEEL DUCT TO DISHWASHER EXHAUST. REFER TO DISHWASHER MANUFACTURER FOR DETAILS OF DUCT CONNECTION.
AutoCAD SHX Text
DRAWING NOTES:
AutoCAD SHX Text
PHASING LEGEND
AutoCAD SHX Text
CURRENT PHASE OF WORK
AutoCAD SHX Text
PHASE OF WORK PREVIOUSLY COMPLETED/PHASE OF WORK YET TO COMMENCE
AutoCAD SHX Text
CONTRACTOR IS RESPONSIBLE FOR COORDINATING THE DEMOLITION OF ANY HVAC SERVICES THAT CROSS BETWEEN PHASE 1 AND PHASE 2 OF THE RENOVATION AREA. PROVIDE TEMPORARY CAPS AS REQUIRED TO FACILITATE THIS WORK. REFER TO ARCHITECTURAL DRAWINGS FOR PHASING BOUNDARY.
AutoCAD SHX Text
A
AutoCAD SHX Text
4
AutoCAD SHX Text
NEW 12x12 STAINLESS STEEL EXHAUST DUCT UP. CONNECT NEW DUCT TO EF-2. REFER TO DRAWING M203 AND M204 FOR CONTINUATION.
AutoCAD SHX Text
5
AutoCAD SHX Text
2
AutoCAD SHX Text
1
AutoCAD SHX Text
ALL DIAMETERS SHOWN FOR GREASE DUCT ARE INSIDE DIAMETER.
AutoCAD SHX Text
B
AutoCAD SHX Text
CONNECT 24x12 DUCT DOWN TO KITCHEN HOOD SUPPLY DUCT COLLAR. BALANCE AIRFLOW FOR EACH CONNECTION TO 1463 CFM.
AutoCAD SHX Text
CONNECT 14 DUCT DOWN TO KITCHEN HOOD EXHAUST DUCT COLLAR. BALANCE AIRFLOW AT EACHCONNECTION TO 1829 CFM.
AutoCAD SHX Text
GREASE DUCT FROM KITCHEN HOOD CONNECTOR TO EXHAUST FAN EF-1 INLET SHALL BE PROTECTED EF-1 INLET SHALL BE PROTECTED INLET SHALL BE PROTECTED GREASE DUCT WITH INTEGRAL CHASE. REFER TO SPEC 23 31 21 FOR FURTHER REQUIREMENTS.
AutoCAD SHX Text
1
AutoCAD SHX Text
6
AutoCAD SHX Text
RE-CONNECT 20x20 DUCT INSTALLED IN PHASE 1 TO NEW 36x20 DUCT UP TO NEW EF-8N. REFER EF-8N. REFER . REFER TO DRAWING M203 FOR CONTINUATION.
AutoCAD SHX Text
7
AutoCAD SHX Text
NEW 36x20 EXHAUST DUCT UP. CONNECT NEW DUCT TO NEW EXHAUST FAN EF-8N. REFER TO EF-8N. REFER TO . REFER TO DRAWING M203 FOR CONTINUATION.
AutoCAD SHX Text
8
AutoCAD SHX Text
CONTRACTOR TO INSTALL EF-8N AND ASSOCIATED NEW DUCTWORK SHOWN IN THIS DRAWING DURING EF-8N AND ASSOCIATED NEW DUCTWORK SHOWN IN THIS DRAWING DURING AND ASSOCIATED NEW DUCTWORK SHOWN IN THIS DRAWING DURING PHASE 2 OF RENOVATION. REFER TO DRAWING M203 FOR FURTHER INFORMATION.
AutoCAD SHX Text
1
AutoCAD SHX Text
THIS DRAWING IS TO BE READ IN CONJUNCTION WITH DRAWING
AutoCAD SHX Text
DRAWING
AutoCAD SHX Text
PROJECT:
AutoCAD SHX Text
TITLE:
AutoCAD SHX Text
SCALE:
AutoCAD SHX Text
DATE:
AutoCAD SHX Text
PROJECT No:
AutoCAD SHX Text
DRAWING No:
AutoCAD SHX Text
REV:
AutoCAD SHX Text
REVIEWED BY:
AutoCAD SHX Text
BAYCREST CENTER FOR GERIATRIC CARE
AutoCAD SHX Text
WAGMAN CENTRE MAIN KITCHEN
AutoCAD SHX Text
FIRST FLOOR - HVAC NEW PHASE 2
AutoCAD SHX Text
EXHAUST REVISIONS
AutoCAD SHX Text
1/8" = 1'
AutoCAD SHX Text
2017/11/27
AutoCAD SHX Text
2171127-01
AutoCAD SHX Text
SK-M202.2
AutoCAD SHX Text
M202.2
PENTHOUSEMECHANICAL ROOM
B58
B57
B56
B55
D24
A18 A19A17
HHAngus & Associates Limited Consulting Engineers1127 Les l ie Street, Toronto, ON, M3C 2J6 Canadawww.hhangus.com | T 416 443 8200 | F 416 443 8290
AutoCAD SHX Text
REMOVE EXISTING EXHAUST FAN EF-8 DURING PHASE 2 OF EF-8 DURING PHASE 2 OF DURING PHASE 2 OF CONSTRUCTION. INCLUDING ASSOCIATED DUCTWORK AND FLEXIBLE CONNECTORS AND MOTORIZED DAMPER. REMOVE ASSOCIATED CONTROLS AND DISCONNECT. REMOVE HOUSEKEEPING PAD AND REPAIR FLOOR.
AutoCAD SHX Text
EF-8
AutoCAD SHX Text
REPAIR PLENUM AS REQUIRED UPON REMOVING EXHAUST DUCTWORK.
AutoCAD SHX Text
EF-6
AutoCAD SHX Text
EF-9
AutoCAD SHX Text
HWR
AutoCAD SHX Text
HWS
AutoCAD SHX Text
CHWS
AutoCAD SHX Text
CHWR
AutoCAD SHX Text
EXISTING HEATING WATER AND CHILLED WATER PIPING TO REMAIN.
AutoCAD SHX Text
REMOVE SECTION OF EXISTING 28x12 SANITARY EXHAUST DUCTWORK TO FACILITATE THE INSTALLATION OF NEW GREASE EXHAUST DUCT. COORDINATE TEMPORARY SHUTDOWN OF EF-6 WITH OWNER. REFER TO DRAWING M-203.2.
AutoCAD SHX Text
CAP
AutoCAD SHX Text
CAP
AutoCAD SHX Text
28x12
AutoCAD SHX Text
MECHANICAL ROOM EXHAUST FAN EF-9 AND ASSOCIATED DUCTWORK TO BE REMOVED AND RELOCATED TO FACILITATE NEW GREASE EXHAUST DUCT INSTALLATION. REFER TO DRAWING M-203.2. REPAIR PLENUM AS REQUIRED.
AutoCAD SHX Text
1
AutoCAD SHX Text
ACCESS
AutoCAD SHX Text
1
AutoCAD SHX Text
THIS DRAWING IS TO BE READ IN CONJUNCTION WITH DRAWING
AutoCAD SHX Text
DRAWING
AutoCAD SHX Text
PROJECT:
AutoCAD SHX Text
TITLE:
AutoCAD SHX Text
SCALE:
AutoCAD SHX Text
DATE:
AutoCAD SHX Text
PROJECT No:
AutoCAD SHX Text
DRAWING No:
AutoCAD SHX Text
REV:
AutoCAD SHX Text
REVIEWED BY:
AutoCAD SHX Text
BAYCREST CENTER FOR GERIATRIC CARE
AutoCAD SHX Text
WAGMAN CENTRE MAIN KITCHEN
AutoCAD SHX Text
PENTHOUSE MECHANICAL ROOM - HVAC DEMOLITION
AutoCAD SHX Text
DEMOLITION REVISIONS/RELOCATIONS
AutoCAD SHX Text
1/8" = 1'
AutoCAD SHX Text
2017/11/27
AutoCAD SHX Text
2171127-01
AutoCAD SHX Text
SK-M203.1
AutoCAD SHX Text
M203.1
PENTHOUSEMECHANICAL ROOM
FIRST FLOOR ROOF
B58
B57
B56
B55
B59
B54
D24
A18 A19A17A16
HHAngus & Associates Limited Consulting Engineers1127 Les l ie Street, Toronto, ON, M3C 2J6 Canadawww.hhangus.com | T 416 443 8200 | F 416 443 8290
AutoCAD SHX Text
64x20
AutoCAD SHX Text
36x24
AutoCAD SHX Text
36x20
AutoCAD SHX Text
MD
AutoCAD SHX Text
EF-8N
AutoCAD SHX Text
30 GREASE DUCT UPAND DOWN. PROVIDE FIRE STOPPING AS REQUIRED AT SLAB PENETRATION. REFER TO DRAWING M-202.1 AND M204 FOR CONTINUATION.
AutoCAD SHX Text
INTAKE HOOD
AutoCAD SHX Text
EDGE OF ROOF
AutoCAD SHX Text
MAINTAIN MINIMUM CLEARANCE OF 7.5m (25') FROM MAU-1 MAU-1 INTAKE TO ANY EXHAUST OR VENT.
AutoCAD SHX Text
MAU-1
AutoCAD SHX Text
1
AutoCAD SHX Text
3
AutoCAD SHX Text
DUCTWORK ROOF SUPPORT. TYPICAL.
AutoCAD SHX Text
36x24
AutoCAD SHX Text
FD
AutoCAD SHX Text
PROVIDE DUCTWORK INSULATION C/W METAL JACKETING.
AutoCAD SHX Text
BD
AutoCAD SHX Text
PROVIDE INSULATED BALANCING DAMPER. SET DAMPER TO MAINTAIN MINIMUM 3800 CFM SUPPLY FROM MAU-1 UPON MAU-1 UPON UPON COMPLETION OF PHASE 1 OF CONSTRUCTION. UPON COMPLETION OF PHASE 2 OF CONSTRUCTION, REMOVE BALANCING DAMPER, CUT BACK AND CAP 10x10 DUCTWORK.
AutoCAD SHX Text
10x10
AutoCAD SHX Text
PROVIDE FIRE DAMPER AT FLOOR PENETRATION.
AutoCAD SHX Text
EF-8N SHALL DISCHARGE INTO EXHAUST SHALL DISCHARGE INTO EXHAUST AIR PLENUM. OPENING TO PLENUM TO MATCH SIZE OF EF-8N DISCHARGE DUCT.EF-8N DISCHARGE DUCT. DISCHARGE DUCT.
AutoCAD SHX Text
10x10 DUCT TURNED DOWN C/W STAINLESS STEEL INSECT MESH. PROVIDE DUCTWORK INSULATION C/W METAL JACKET
AutoCAD SHX Text
EF-6
AutoCAD SHX Text
EF-9
AutoCAD SHX Text
HWR
AutoCAD SHX Text
HWS
AutoCAD SHX Text
CHWS
AutoCAD SHX Text
CHWR
AutoCAD SHX Text
EXISTING HEATING WATER AND CHILLED WATER PIPING TO REMAIN.
AutoCAD SHX Text
28x12
AutoCAD SHX Text
28x12
AutoCAD SHX Text
EXISTING MECHANICAL ROOM EXHAUST FAN EF-9 RELOCATED TO FACILITATE INSTALLATION OF NEW GREASE EXHAUST DUCT. EF-9 TO BE CEILING MOUNTED. BOTTOM OF FAN SHALL BE AT LEAST 10' AFF. COORDINATE LOCATION WITH EXISTING SERVICES WITHIN MECHANICAL ROOM. PROVIDE NEW DUCTWORK TO MATCH EF-9 OUTLET SIZE AND DISCHARGE INTO PLENUM.
AutoCAD SHX Text
4
AutoCAD SHX Text
1
AutoCAD SHX Text
1
AutoCAD SHX Text
ACCESS
AutoCAD SHX Text
DUCTWORK FROM MAU-1 UP TO MAU-1 UP TO UP TO ROOF PENETRATION SHALL BE G20 ZINC COATED GALVANIZED STEEL.
AutoCAD SHX Text
1
AutoCAD SHX Text
MOUNT UNIT ON SPRING ISOLATED ROOF CURB WITH ISOLATION RAILS. INSTALL AS PER MANUFACTURER SPECIFICATIONS.
AutoCAD SHX Text
1
AutoCAD SHX Text
FLEXIBLE CONNECTION
AutoCAD SHX Text
1
AutoCAD SHX Text
PROVIDE NEW HOUSEKEEP PAD FOR EF-8N AS PER SPEC. AS PER SPEC.
AutoCAD SHX Text
1
AutoCAD SHX Text
GENERAL NOTES
AutoCAD SHX Text
1
AutoCAD SHX Text
PROVIDE NEW ROOFTOP MAKE UP AIR UNIT MAU-1. REFER TO SCHEDULE MAU-1. REFER TO SCHEDULE . REFER TO SCHEDULE FOR FURTHER INFORMATION ON MAKE-UP AIR UNIT. MAU-1 SHALL BE MAU-1 SHALL BE SHALL BE PROVIDED C/W SPRING ISOLATED ROOF CURB WITH ISOLATION RAILS, REFER TO DETAIL M502.2 FOR FURTHER INFORMATION.
AutoCAD SHX Text
DRAWING NOTES:
AutoCAD SHX Text
A
AutoCAD SHX Text
2
AutoCAD SHX Text
ALL DUCTWORK ASSOCIATED WITH DISHWASHER EXHAUST FAN EF-2 TO BE EF-2 TO BE TO BE TO BE STAINLESS STEEL.
AutoCAD SHX Text
3
AutoCAD SHX Text
GREASE DUCT FROM KITCHEN HOOD CONNECTOR TO EXHAUST FAN EF-1 EF-1 INLET SHALL BE PROTECTED GREASE DUCT WITH INTEGRAL CHASE. REFER TO SPEC 23 31 21 FOR FURTHER REQUIREMENTS.
AutoCAD SHX Text
CONTRACTOR IS RESPONSIBLE FOR COORDINATING ALL NEW WORK WITH EXISTING SERVICES WITHIN THE PENTHOUSE MECHANICAL ROOM.
AutoCAD SHX Text
B
AutoCAD SHX Text
RETAIN REGISTERED STRUCTURAL ENGINEER TO REVIEW AND APPROVE ALL OPENINGS ON FLOOR AND ROOF, AND DESIGN RE-INFORCEMENT FOR FLOOR AND ROOF OPENINGS IF REQUIRED. PROVIDE STRUCTURAL RE-INFORCEMENT FOR FLOOR AND ROOF OPENINGS REQUIRED BY STRUCTURAL ENGINEER.
AutoCAD SHX Text
4
AutoCAD SHX Text
PROVIDE NEW SECTION OF 28x12 DUCTWORK AND OFFSET TO FACILITATE INSTALLATION OF NEW GREASE EXHAUST DUCT.
AutoCAD SHX Text
1
AutoCAD SHX Text
THIS DRAWING IS TO BE READ IN CONJUNCTION WITH DRAWING
AutoCAD SHX Text
DRAWING
AutoCAD SHX Text
PROJECT:
AutoCAD SHX Text
TITLE:
AutoCAD SHX Text
SCALE:
AutoCAD SHX Text
DATE:
AutoCAD SHX Text
PROJECT No:
AutoCAD SHX Text
DRAWING No:
AutoCAD SHX Text
REV:
AutoCAD SHX Text
REVIEWED BY:
AutoCAD SHX Text
BAYCREST CENTER FOR GERIATRIC CARE
AutoCAD SHX Text
WAGMAN CENTRE MAIN KITCHEN
AutoCAD SHX Text
PENTHOUSE MECHANICAL ROOM - HVAC NEW
AutoCAD SHX Text
VENTILATION REVISIONS/RELOCATIONS
AutoCAD SHX Text
1/8" = 1'
AutoCAD SHX Text
2017/11/27
AutoCAD SHX Text
2171127-01
AutoCAD SHX Text
SK-M203.2
AutoCAD SHX Text
M203.2
B61
B59
B60
A22A20 A21 A23 A24
HHAngus & Associates Limited Consulting Engineers1127 Les l ie Street, Toronto, ON, M3C 2J6 Canadawww.hhangus.com | T 416 443 8200 | F 416 443 8290
AutoCAD SHX Text
26x16
AutoCAD SHX Text
66x30
AutoCAD SHX Text
72x54
AutoCAD SHX Text
12x12 STAINLESS STEEL DUCT DOWN TO DISHWASHER. RUN DUCT AT HIGH LEVEL WITHIN PENTHOUSE. REFER TO DRAWING M-202.2 FOR CONTINUATION.
AutoCAD SHX Text
12x12
AutoCAD SHX Text
FD
AutoCAD SHX Text
PROVIDE STAINLESS STEEL FIRE DAMPER AT SLAB PENETRATION.
AutoCAD SHX Text
2
AutoCAD SHX Text
1
AutoCAD SHX Text
DRAWING NOTES:
AutoCAD SHX Text
2
AutoCAD SHX Text
ALL DUCTWORK ASSOCIATED WITH DISHWASHER EXHAUST FAN EF-2 TO BE EF-2 TO BE TO BE TO BE STAINLESS STEEL.
AutoCAD SHX Text
THIS DRAWING IS TO BE READ IN CONJUNCTION WITH DRAWING
AutoCAD SHX Text
DRAWING
AutoCAD SHX Text
PROJECT:
AutoCAD SHX Text
TITLE:
AutoCAD SHX Text
SCALE:
AutoCAD SHX Text
DATE:
AutoCAD SHX Text
PROJECT No:
AutoCAD SHX Text
DRAWING No:
AutoCAD SHX Text
REV:
AutoCAD SHX Text
REVIEWED BY:
AutoCAD SHX Text
BAYCREST CENTER FOR GERIATRIC CARE
AutoCAD SHX Text
WAGMAN CENTRE MAIN KITCHEN
AutoCAD SHX Text
PENTHOUSE MECHANICAL ROOM - HVAC NEW
AutoCAD SHX Text
DISHWASHER EXHAUST REVISIONS
AutoCAD SHX Text
1/8" = 1'
AutoCAD SHX Text
2017/11/27
AutoCAD SHX Text
2171127-01
AutoCAD SHX Text
SK-M203.3
AutoCAD SHX Text
M203.2
D21
C9
A18 A19 A20 A21A17 A23
B61
B58
B57
B56
A16
A15
B55
A22
B59
A24
C10
C8
D24
B58
B59
B54 B54
A18 A19 A20 A21A17 A23A16 A24
D24
B57
B56
B55
B62
B60
A22A15
EX HSK
EX SHAFT
EX DRY STOREX FREEZER EX REF EX REF
EX KITCHEN
EX CONFERENCE
EX OFFICE
EX DISHWASH
EX MENEX
EX WOMENEX
EX ELEV 5
EX ELEV 4EX
D21
C9
A18 A19 A20 A21A17 A23
B61
B58
B57
B56
A16
A15
B55
A22
B59
A24
C10
C8
D24
B58
B59
B54 B54
A18 A19 A20 A21A17 A23A16 A24
D24
B57
B56
B55
B62
B60
A22A15
EX WOMENSEX
EX MENSEX
EX CIRCUT04
EX CORRIDOR01 EX CORRIDOR
03
EX TW CAFE013
EX CORRIDOR010
EX PARTY017
EX MACHINE08
EX CORRIDOR011
EX STORAGE07
EX DISHWASHING015
EX CHAIR STORAGE018
EX HOUSEKEEPING09
EX PROJECT KITCHEN016
EX SERVERY014
EX CORRIDOR02
EX RECEIVING06
EX VEST020
GREASE INTERCEPTOR05
FIRST FLOOR - FIRE
PROTECTION
DEMOLITION,
GROUND FLOOR - FIRE
PROTECTION
M301
1/8" = 1'
1100 Liberty Avenue
Pittsburgh, PA 15222
T. +1 412 456 0900
F. +1 412 456 0906
KEY PLAN
Owner:
Structural:
Mechanical, Electrical, & Plumbing:
Food Service:
Code Consultant:
SCALE:
DRAWING TITLE:
PROJECT TITLE:
PROJECT No:
BAYCREST HEALTH SCIENCES
55 AMEER AVENUE,
TORONTO, ONTARIO, MGA 2Z1
ENTUITIVE
200 UNIVERSITY AVENUE, 7TH FLOOR,
TORONTO, ONTARIO, M5H 3C6
FOOD FACILITIES CONCEPTS, INC.
1100 WASHINGTON AVE, SUITE 302
CARNEGIE, PA 15106
JENSEN HUGHES
2150 ISLINGTON AVE, SUITE 100
TORONTO, ONTARIO, M9P 3V4
BAYCREST CENTRE
FOR GERIATRIC CARE
55 AMEER AVENUE, TORONTO,
ONTARIO, MGA 2Z1
WAGMAN
CENTRE KITCHEN
RENOVATION
2171127-01
NOVEMBER 9, 2017
FOR TENDER AND PERMIT
SEAL
HHAngus & Associates Limited Consulting Engineers1127 Lesl ie Street, Toronto, ON, M3C 2J6 Canadawww.hhangus.com | T 416 443 8200 | F 416 443 8290
DATENO. ISSUE
AutoCAD SHX Text
4"
AutoCAD SHX Text
3 "12"
AutoCAD SHX Text
3 "12"
AutoCAD SHX Text
3 "12"
AutoCAD SHX Text
3"
AutoCAD SHX Text
2 "12"
AutoCAD SHX Text
2 "12"
AutoCAD SHX Text
2"
AutoCAD SHX Text
2"
AutoCAD SHX Text
1"
AutoCAD SHX Text
1 "12"
AutoCAD SHX Text
2 "12"
AutoCAD SHX Text
2 "12"
AutoCAD SHX Text
2 "12"
AutoCAD SHX Text
2 "12"
AutoCAD SHX Text
2"
AutoCAD SHX Text
1 "12"
AutoCAD SHX Text
1"
AutoCAD SHX Text
1"
AutoCAD SHX Text
1"
AutoCAD SHX Text
1"
AutoCAD SHX Text
1 "14"
AutoCAD SHX Text
1"
AutoCAD SHX Text
1"
AutoCAD SHX Text
1"
AutoCAD SHX Text
1"
AutoCAD SHX Text
2 "12"
AutoCAD SHX Text
2"
AutoCAD SHX Text
1"
AutoCAD SHX Text
1"
AutoCAD SHX Text
1 "12"
AutoCAD SHX Text
1"
AutoCAD SHX Text
1"
AutoCAD SHX Text
1"
AutoCAD SHX Text
1 "12"
AutoCAD SHX Text
1 "14"
AutoCAD SHX Text
1"
AutoCAD SHX Text
CAP
AutoCAD SHX Text
CAP
AutoCAD SHX Text
CAP
AutoCAD SHX Text
CAP
AutoCAD SHX Text
1
AutoCAD SHX Text
1
AutoCAD SHX Text
1
AutoCAD SHX Text
1
AutoCAD SHX Text
1
AutoCAD SHX Text
1
AutoCAD SHX Text
1
AutoCAD SHX Text
1
AutoCAD SHX Text
1
AutoCAD SHX Text
1
AutoCAD SHX Text
1
AutoCAD SHX Text
1
AutoCAD SHX Text
1
AutoCAD SHX Text
1
AutoCAD SHX Text
1
AutoCAD SHX Text
1
AutoCAD SHX Text
1
AutoCAD SHX Text
1
AutoCAD SHX Text
1
AutoCAD SHX Text
1
AutoCAD SHX Text
1
AutoCAD SHX Text
1
AutoCAD SHX Text
1
AutoCAD SHX Text
1
AutoCAD SHX Text
1
AutoCAD SHX Text
1
AutoCAD SHX Text
1
AutoCAD SHX Text
1
AutoCAD SHX Text
1
AutoCAD SHX Text
1
AutoCAD SHX Text
1
AutoCAD SHX Text
1
AutoCAD SHX Text
1
AutoCAD SHX Text
1
AutoCAD SHX Text
2
AutoCAD SHX Text
3
AutoCAD SHX Text
EXISTING SPRINKLER SERVICE
AutoCAD SHX Text
SP
AutoCAD SHX Text
SP
AutoCAD SHX Text
SP
AutoCAD SHX Text
SP
AutoCAD SHX Text
PHASE 1
AutoCAD SHX Text
PHASE 2
AutoCAD SHX Text
PHASE 1
AutoCAD SHX Text
PHASE 2
AutoCAD SHX Text
GENERAL NOTES
AutoCAD SHX Text
COORDINATE WITH FIRE DEPARTMENT AND OWNER FOR SYSTEM SHUTDOWN AS REQUIRED FOR DEMOLITION AND INSTALLATION. PROVIDE FIRE WATCH AS REQUIRED.
AutoCAD SHX Text
A
AutoCAD SHX Text
PROVIDE ON-SITE CRYOGENIC LIQUID NITROGEN PIPE FREEZE TO FACILITATE DEMOLITION AND PREPARATION OF NEW WORK.
AutoCAD SHX Text
B
AutoCAD SHX Text
PROVIDE FOR THE DEMOLITION OF MINIMUM ADDITIONAL 5 SPRINKLER HEADS AND BRANCH PIPING UNDER UNFORESEEN CONDITIONS.
AutoCAD SHX Text
C
AutoCAD SHX Text
DRAWING NOTES
AutoCAD SHX Text
1
AutoCAD SHX Text
REMOVE EXISTING SPRINKLER HEAD AND ASSOCIATED BRANCH PIPING. CAP AT MAIN OR AS REQUIRED TO FACILITATE THE INSTALLATION OF NEW SPRINKLER HEADS.
AutoCAD SHX Text
2
AutoCAD SHX Text
EXISTING SPRINKLER HEAD TO REMAIN. CONTRACTOR RESPONSIBLE FOR ANY DAMAGE.
AutoCAD SHX Text
3
AutoCAD SHX Text
REMOVE ALL FIRE PROTECTION SERVICES ASSOCIATED WITH THE KITCHEN HOOD, INCLUDING SPECIALIZED SUPPRESSION SYSTEM. CUT BACK AND CAP FIRE PROTECTION SERVICES AS REQUIRED.
AutoCAD SHX Text
CONTRACTOR IS RESPONSIBLE FOR COORDINATING THE DEMOLITION OF ANY FIRE PROTECTION SERVICES THAT CROSS BETWEEN PHASE 1 AND PHASE 2 OF THE RENOVATION AREA. PROVIDE TEMPORARY CAPS, CRYOGENIC LIQUID NITROGEN PIPE FREEZE AND FIRE WATCH AS REQUIRED TO FACILITATE THIS WORK. REFER TO ARCHITECTURAL DRAWINGS FOR PHASING BOUNDARY.
AutoCAD SHX Text
D
AutoCAD SHX Text
PHASING LEGEND
AutoCAD SHX Text
DELINEATION BETWEEN PHASE 1 AND PHASE 2
AutoCAD SHX Text
4"
AutoCAD SHX Text
3 "12"
AutoCAD SHX Text
3 "12"
AutoCAD SHX Text
3 "12"
AutoCAD SHX Text
3 "12"
AutoCAD SHX Text
3"
AutoCAD SHX Text
3"
AutoCAD SHX Text
3"
AutoCAD SHX Text
2 "12"
AutoCAD SHX Text
2"
AutoCAD SHX Text
4"
AutoCAD SHX Text
4"
AutoCAD SHX Text
3 "12"
AutoCAD SHX Text
2"
AutoCAD SHX Text
2"
AutoCAD SHX Text
1 "12"
AutoCAD SHX Text
1"
AutoCAD SHX Text
1"
AutoCAD SHX Text
1"
AutoCAD SHX Text
2 "12"
AutoCAD SHX Text
2 "12"
AutoCAD SHX Text
2"
AutoCAD SHX Text
1 "12"
AutoCAD SHX Text
1"
AutoCAD SHX Text
1"
AutoCAD SHX Text
1"
AutoCAD SHX Text
1"
AutoCAD SHX Text
1"
AutoCAD SHX Text
1"
AutoCAD SHX Text
1"
AutoCAD SHX Text
1"
AutoCAD SHX Text
2"
AutoCAD SHX Text
1 "12"
AutoCAD SHX Text
1 "14"
AutoCAD SHX Text
1"
AutoCAD SHX Text
1"
AutoCAD SHX Text
1"
AutoCAD SHX Text
1 "14"
AutoCAD SHX Text
1"
AutoCAD SHX Text
1"
AutoCAD SHX Text
2 "12"
AutoCAD SHX Text
1 "12"
AutoCAD SHX Text
2"
AutoCAD SHX Text
1 "14"
AutoCAD SHX Text
1 "14"
AutoCAD SHX Text
1"
AutoCAD SHX Text
2 "12"
AutoCAD SHX Text
2"
AutoCAD SHX Text
1 "12"
AutoCAD SHX Text
1"
AutoCAD SHX Text
1 "14"
AutoCAD SHX Text
1"
AutoCAD SHX Text
1 "14"
AutoCAD SHX Text
1"
AutoCAD SHX Text
2 "12"
AutoCAD SHX Text
1 "12"
AutoCAD SHX Text
2"
AutoCAD SHX Text
1"
AutoCAD SHX Text
1 "12"
AutoCAD SHX Text
3"
AutoCAD SHX Text
1"
AutoCAD SHX Text
1 "14"
AutoCAD SHX Text
1"
AutoCAD SHX Text
3"
AutoCAD SHX Text
1
AutoCAD SHX Text
1
AutoCAD SHX Text
1
AutoCAD SHX Text
1
AutoCAD SHX Text
1
AutoCAD SHX Text
1
AutoCAD SHX Text
1
AutoCAD SHX Text
1
AutoCAD SHX Text
1
AutoCAD SHX Text
1
AutoCAD SHX Text
1
AutoCAD SHX Text
1
AutoCAD SHX Text
1
AutoCAD SHX Text
1
AutoCAD SHX Text
1
AutoCAD SHX Text
1
AutoCAD SHX Text
2
AutoCAD SHX Text
2
AutoCAD SHX Text
2
AutoCAD SHX Text
2
AutoCAD SHX Text
2
AutoCAD SHX Text
2
AutoCAD SHX Text
2
AutoCAD SHX Text
2
AutoCAD SHX Text
2
AutoCAD SHX Text
2
AutoCAD SHX Text
2
AutoCAD SHX Text
2
AutoCAD SHX Text
2
AutoCAD SHX Text
2
AutoCAD SHX Text
2
AutoCAD SHX Text
2
AutoCAD SHX Text
2
AutoCAD SHX Text
2
AutoCAD SHX Text
2
AutoCAD SHX Text
2
AutoCAD SHX Text
2
AutoCAD SHX Text
2
AutoCAD SHX Text
2
AutoCAD SHX Text
2
AutoCAD SHX Text
2
AutoCAD SHX Text
2
AutoCAD SHX Text
2
AutoCAD SHX Text
2
AutoCAD SHX Text
2
AutoCAD SHX Text
2
AutoCAD SHX Text
2
AutoCAD SHX Text
2
AutoCAD SHX Text
2
AutoCAD SHX Text
2
AutoCAD SHX Text
2
AutoCAD SHX Text
2
AutoCAD SHX Text
2
AutoCAD SHX Text
2
AutoCAD SHX Text
2
AutoCAD SHX Text
2
AutoCAD SHX Text
CAP
AutoCAD SHX Text
3
AutoCAD SHX Text
4
AutoCAD SHX Text
3
AutoCAD SHX Text
CAP
AutoCAD SHX Text
4
AutoCAD SHX Text
2
AutoCAD SHX Text
2
AutoCAD SHX Text
2
AutoCAD SHX Text
2
AutoCAD SHX Text
NEW GREASE INTERCEPTOR ROOM. REFER TO ARCHITECTURAL PLANS FOR FURTHER INFORMATION.
AutoCAD SHX Text
GENERAL NOTES
AutoCAD SHX Text
COORDINATE WITH FIRE DEPARTMENT AND OWNER FOR SYSTEM SHUTDOWN AS REQUIRED FOR DEMOLITION AND INSTALLATION. PROVIDE FIRE WATCH AS REQUIRED.
AutoCAD SHX Text
A
AutoCAD SHX Text
PROVIDE ON-SITE CRYOGENIC LIQUID NITROGEN PIPE FREEZE TO FACILITATE DEMOLITION AND PREPARATION OF NEW WORK.
AutoCAD SHX Text
B
AutoCAD SHX Text
PROVIDE FOR THE DEMOLITION, INSTALLATION AND RELOCATION OF MINIMUM ADDITIONAL 5 SPRINKLER HEADS AND BRANCH PIPING UNDER UNFORESEEN CONDITIONS.
AutoCAD SHX Text
C
AutoCAD SHX Text
DRAWING NOTES
AutoCAD SHX Text
1
AutoCAD SHX Text
EXISTING CEILING WITHIN THIS ROOM IS BEING REMOVED (REFER TO ARCHITECTURAL SERIES DRAWINGS). REMOVE EXISTING PENDANT SPRINKLER HEAD, CUT BACK AND CAP ASSOCIATED BRANCH PIPING. PROVIDE NEW UPRIGHT SPRINKLER HEAD AND ASSOCIATED BRANCH PIPING AS REQUIRED TO MEET NFPA 13.
AutoCAD SHX Text
REFER TO ARCHITECTURAL SERIES DRAWINGS FOR EXTENT OF CEILING REMOVAL. IN SPACES WHERE CEILING IS BEING REMOVED, PROVIDE SPRINKLER HEADS AND BRANCH PIPING UNDER ALL FIXED OBSTRUCTIONS IN ACCORDANCE WITH NFPA 13. CONNECT BRANCH PIPING TO MAIN OF ADEQUATE SIZE. CONTRACTOR TO INSPECT ALL DUCTWORK AND PROVIDE SPRINKLER HEADS AS REQUIRED TO MEET NFPA 13.
AutoCAD SHX Text
D
AutoCAD SHX Text
2
AutoCAD SHX Text
EXISTING SPRINKLER HEAD TO REMAIN. CONTRACTOR RESPONSIBLE FOR ANY DAMAGE.
AutoCAD SHX Text
ALL SYSTEMS SHALL BE HYDRAULICALLY SIZED. ALL PIPE SIZING SHALL BE BASED ON CONTRACTOR'S OWN HYDRAULIC CALCULATIONS AT NO ADDITIONAL COST TO THE OWNER. PROVIDE ADDITIONAL HEADS AS REQUIRED TO MEET NFPA 13.
AutoCAD SHX Text
E
AutoCAD SHX Text
COORDINATE LOCATION OF NEW SPRINKLER HEADS WITH ARCHITECTURAL PLANS AND OTHER DISCIPLINES. REFER TO ARCHITECTURAL SERIES DRAWINGS.
AutoCAD SHX Text
F
AutoCAD SHX Text
0.2
AutoCAD SHX Text
0.15
AutoCAD SHX Text
0.1
AutoCAD SHX Text
(USGPM/1500ft2)
AutoCAD SHX Text
DESIGN DENSITY
AutoCAD SHX Text
ORDINARY HAZARD (GROUP 2)
AutoCAD SHX Text
LARGE STORAGE AREAS
AutoCAD SHX Text
DIESEL STORAGE ROOM
AutoCAD SHX Text
CLINICAL
AutoCAD SHX Text
PHARMACY
AutoCAD SHX Text
MECHANICAL SERVICE AREAS
AutoCAD SHX Text
ORDINARY HAZARD (GROUP 1)
AutoCAD SHX Text
KITCHEN AREAS
AutoCAD SHX Text
LABORATORY AREAS
AutoCAD SHX Text
LAUNDRY AREAS
AutoCAD SHX Text
ASSEMBLY AREAS
AutoCAD SHX Text
OFFICE AREAS
AutoCAD SHX Text
PATIENT CARE AREAS
AutoCAD SHX Text
LIGHT HAZARD
AutoCAD SHX Text
HAZARD CLASSIFICATIONS
AutoCAD SHX Text
SPRINKLER HEAD DISCHARGE DENSITIES
AutoCAD SHX Text
3
AutoCAD SHX Text
REMOVE EXISTING SPRINKLER AND CAP ASSOCIATED BRANCH PIPING.
AutoCAD SHX Text
4
AutoCAD SHX Text
PROVIDE NEW PENDANT TYPE SPRINKLER HEAD AND ASSOCIATED BRANCH PIPING. CONNECT BRANCH PIPING TO MAIN OF ADEQUATE SIZE. LOCATE NEW SPRINKLER HEAD AS REQUIRED TO MEET NFPA 13.
AutoCAD SHX Text
1
AutoCAD SHX Text
M301
AutoCAD SHX Text
FIRST FLOOR FIRE PROTECTION DEMOLITION
AutoCAD SHX Text
1/8" = 1'
AutoCAD SHX Text
2
AutoCAD SHX Text
M301
AutoCAD SHX Text
GROUND FLOOR FIRE PROTECTION
AutoCAD SHX Text
1/8" = 1'
AutoCAD SHX Text
1
AutoCAD SHX Text
1. 11/27/2017 ISSUED FOR ADD. M-1
AutoCAD SHX Text
1
HHAngus & Associates Limited Consulting Engineers1127 Les l ie Street, Toronto, ON, M3C 2J6 Canadawww.hhangus.com | T 416 443 8200 | F 416 443 8290
AutoCAD SHX Text
2
AutoCAD SHX Text
M502
AutoCAD SHX Text
N.T.S.
AutoCAD SHX Text
MAKE-UP AIR UNIT (MAU-1) SPRING ISOLATED ROOF CURB DETAILSMAU-1) SPRING ISOLATED ROOF CURB DETAILS) SPRING ISOLATED ROOF CURB DETAILS
AutoCAD SHX Text
1
AutoCAD SHX Text
ROOFTOP UNIT BASE.
AutoCAD SHX Text
%%UNOTES:
AutoCAD SHX Text
2
AutoCAD SHX Text
SPRING ISOLATION
AutoCAD SHX Text
3
AutoCAD SHX Text
ELASTOMERIC MASTIC FLASHING TO GO OVER ROOF CURB
AutoCAD SHX Text
4
AutoCAD SHX Text
ELASTOMERIC OF FIELD PLIES ABOVE CANT STRIP
AutoCAD SHX Text
5
AutoCAD SHX Text
MASTIC ROOFING PLIES
AutoCAD SHX Text
6
AutoCAD SHX Text
316 S.S. SCREWED FASTENERS
AutoCAD SHX Text
7
AutoCAD SHX Text
ELASTOMERIC MASTIC & MESH ON LEADING EDGE
AutoCAD SHX Text
8
AutoCAD SHX Text
CURB COUNTER FLASHING
AutoCAD SHX Text
9
AutoCAD SHX Text
CANT STRIP
AutoCAD SHX Text
10
AutoCAD SHX Text
INSULATED ROOF CURB
AutoCAD SHX Text
1
AutoCAD SHX Text
2
AutoCAD SHX Text
3
AutoCAD SHX Text
4
AutoCAD SHX Text
5
AutoCAD SHX Text
6
AutoCAD SHX Text
7
AutoCAD SHX Text
8
AutoCAD SHX Text
9
AutoCAD SHX Text
10
AutoCAD SHX Text
11
AutoCAD SHX Text
ROOF INSULATION
AutoCAD SHX Text
11
AutoCAD SHX Text
1
AutoCAD SHX Text
THIS DRAWING IS TO BE READ IN CONJUNCTION WITH DRAWING
AutoCAD SHX Text
DRAWING
AutoCAD SHX Text
PROJECT:
AutoCAD SHX Text
TITLE:
AutoCAD SHX Text
SCALE:
AutoCAD SHX Text
DATE:
AutoCAD SHX Text
PROJECT No:
AutoCAD SHX Text
DRAWING No:
AutoCAD SHX Text
REV:
AutoCAD SHX Text
REVIEWED BY:
AutoCAD SHX Text
BAYCREST CENTER FOR GERIATRIC CARE
AutoCAD SHX Text
WAGMAN CENTRE MAIN KITCHEN
AutoCAD SHX Text
DETAILS II
AutoCAD SHX Text
MAU-1 SPRING ISOLATED ROOF CURB REVISION
AutoCAD SHX Text
N.T.S.
AutoCAD SHX Text
2017/11/27
AutoCAD SHX Text
2171127-01
AutoCAD SHX Text
SK-M502.1
AutoCAD SHX Text
M502
Baycrest Center for Geriatric Care Wagman Centre Kitchen Renovation HHA #2171127-01
Section 00 91 13 E-1Addenda
Page 1 of 1
ADDENDA 00 91 13 E-1
The information listed below is to form part of the Contract Documents. All associated costs are to
be included in Tender Price shown on Tender Form. Acknowledgment of this Addendum, by number, to be shown in space provided on Tender Form.
1 DRAWINGS
1.1 E203 – Ground Floor Electrical Plan (new drawing issued herewith)
.1 Provide electrical works as indicated on new drawing attached herewith.
2 SPECIFICATIONS
2.1 26 51 13 – Lighting (not re-issued)
.1 Add lighting Type ‘LB’ as outlined below:
LB Chain hung LED strip fixture. Nominal dimensions of (2'-1/16"W x 2 7/8”D x 4'-0" L). Luminaire shall come complete with a frosted extruded microgrooved round polycarbonate lens with a die and brake-formed code gauge steel housing and ends. The luminaire shall come complete with a thermal management system without the need for additional heat sinks. LED colour temperature shall be 3500K.
Luminaire shall be chain hung. Manufacturer shall provide a 120V/347V transformer to accommodate all fixtures shown on plans.
Luminaire to be complete with all necessary mounting brackets, corner fittings, etc for a complete and working installation. Voltage: 347 volt Manufacturers:
Visioneering: LCOMN48-LED835K040L347 c/w chain
Equals: Lithonia, Eaton
LED Boards
36W
4000 lumens
3500K
CRI ≥ 80
LB1
Same as type ‘LB’ except shall be surface mounted on drywall.
END OF ADDENDUM
END OF SECTION
FDFDFD
FD FD FD
RE
F.
RE
F.
OV
EN
OV
EN
D19
D21
C9
C12
B67
A18
A18
A19
A19
A20
A20
A21
A21
A17
A17
D15
D10
B69
B65
B64
B62
A31A28
A23 A25
A27 A32
B61
B60
B58
A33 A34
B57
B56
A16
A16
A15
B55
B52
B54
B51
A22 A26
B59
A24
B53
D7
B68
B63
D18
C11
C10
D13
A30
D24
1
1
1
1
1
1
2
5
5
5
5
9
9
9
10
38
11
12
ACT9' - 4"
ACT8' - 0"
SAC10' - 0"
CONC10' - 0"
ACT9' - 4"
ACT8' - 0"ACT
9' - 4"
ACT9' - 4"
ACT9' - 4"
ACT8' - 0"
ACT9' - 4"
ACT8' - 0"
CPP8' - 0"
CPP8' - 0"
ACT9' - 4"
GWB8' - 0"
GWB8' - 0"
ACT8' - 0"
CONC10' - 0"
CONC10' - 0"CONC
10' - 0"
CONC10' - 0"
CONC10' - 0"
CONC10' - 0"CONC
10' - 0"
CONC10' - 0"
GWB8' - 6"
GYP BD8' - 4"
ACT8' - 0"
GYP BD7' - 4"
GYP BD7' - 4"
GYP BD7' - 4"
GWB7' - 4"
GWB9' - 0"
ACT9' - 0"
ACT9' - 0"
ACT9' - 0"
ACT8' - 0"
CONC10' - 0"
ACT8' - 0"
ACT8' - 0"
GWB8' - 0"
SAC8' - 0"
CPP8' - 0"
GWB8' - 0"
GWB8' - 0"
11
11
DEMOLITION RCP LEGEND2'-0" X 4'-0" SURFACE-MOUNTED FLUORESCENT FIXTURE TO BE REMOVED
2X4 ACT SYSTEM TO BE REMOVED
2'-0" X 2'-0" RECESSED LAY-IN FLUORESCENT FIXTURE TO BE REMOVED
PENDANT LIGHT FIXTURE TO BE REMOVED
RECESSED FLUORESCENT LIGHT FIXTURE TO BE REMOVED
DECORATIVE WALL SCONCE TO BE REMOVED
EXISTING AREA TO REMAIN UNCHANGED
GYP BD CEILING TO BE REMOVED
EXIT SIGN TO BE REMOVED
DEMOLITION GENERAL NOTES• HAZARDOUS MATERIAL SHALL BE IDENTIFIED AND ABATED PRIOR TO ANY DEMOLITION WORK.
GENERAL CONTRACTOR TO COORDINATE.
• DEMOLITION PLANS INCLUDE WORK REQUIRED FOR RENOVATION, BUT ARE NOT INTENDED TOINCLUDE ALL REQUIREMENTS. DEMOLITION WORK NOT SHOWN ON DRAWINGS OR SPECIFIED WHICH IS REQUIRED FOR COMPLETION OF WORK INCLUDED IN THE CONTRACT DOCUMENTS IS THERESPONSIBILITY OF THE GENERAL CONTRACTOR.
• COORDINATE ALL DEMOLITION WORK WITH ALL TRADES. REVIEW FIELD CONDITIONS & DRAWINGSFOR EXACT LOCATIONS OF OPENINGS AND EXTENT OF DEMOLITION PRIOR TO STARTING WORK.
• REFER TO STRUCTURAL, MECHANICAL, PLUMBING, ELECTRICAL, FOOD SERVICE DRAWINGS ANDPROJECT MANUAL FOR ADDITIONAL INFORMATION REGARDING THE EXTENT OF DEMOLITIONREQUIRED AND THE SYSTEMS AFFECTED.
• ALL STRUCTURAL MEMBERS INCLUDING BEARING WALLS AFFECTED BY THE DEMOLITION ARE TO BE VERIFIED AND ADEQUATELY SHORED BEFORE REMOVAL.
• ALL MASONRY REMOVAL IS TO BE REMOVED BY SAWCUTTING. PATCH AND REPAIR EXPOSED WALLSDAMAGED BY REMOVAL WORK AND LEAVE IN NEAT, CLEAN, FINISHED CONDITION. IN EXPOSEDMASONRY WALLS KEY IN MASONRY TO MATCH SURROUNDING WORK,. REFER TO STRUCTURALDRAWINGS FOR LINTEL REQUIREMENTS.
• REFER TO NEW CONSTRUCTION PLANS FOR DIMENSIONS AND EXTENT OF OPENINGS IN EXISTINGWALLS OR PARTIAL DEMOLITION.
• ALL EXISTING FIRE RESISTANCE RATINGS OF FLOORS, WALLS, SHAFTS, AND CEILINGS ARE TO BEMAINTAINED AND FIELD VERIFIED.
• GENERAL CONTRACTOR TO COORDINATE AND IDENTIFY MASONRY WALLS VS. METAL STUD WALLSPRIOR TO DEMOLITION BID.
• PATCH AND REPAIR ALL ADJACENT MATERIALS TO MATCH EXISTING IN AREAS WHERE DEMOLITIONWORK ABUTS ADJACENT SURFACES TO REMAIN.
• PATCH AND REPAIR ALL EXISTING FIREPROOFING / CLADDING AT STRUCTURAL STEEL AS NEEDEDTO RETAIN REQUIRED FIRE RATINGS.
• WALLS AND ANY OTHER ITEMS SHOWN TO BE REMOVED BY DASHED LINES ARE TO BE REMOVEDENTIRELY TO THE UNDERSIDE OF THE STRUCTURE ABOVE, INCLUDING ANY BUILT-IN FURNITURE,PIPING FOR PLUMBING FIXTURES, LIGHT FIXTURES, AND MECHANICAL EQUIPMENT, UNLESS BEINGREPLACED BY NEW IN THE SAME LOCATION. REFER TO MEP DRAWINGS FOR ADDITIONALINFORMATION.
• EXISTING DRYWALL FINISHES TO BE REPAIRED IN ALL LOCATIONS IN PREPARATION FOR NEW PAINT.
• FLOOR FINISH DEMOLITION: DEMOLISH ALL EXISTING FLOOR FINISH MATERIAL INCLUDING SETTINGMATERIAL. PREPARE SUBFLOOR FOR NEW WORK.
• ALL EXISTING WALL COVERING AND WALL BORDER ARE TO BE REMOVED WHERE DEMOLITIONWORK AND NEW WORK ARE OCCURRING IN PREPARATION FOR NEW FINISHES.
• ALL EXISTING WALL BASE AND CORNER , WALL AND JAMB PROTECTION ARE TO BE REMOVEDWHERE DEMOLITION WORK AND NEW WORK ARE OCCURRING IN PREPARATION FOR NEW FINISHES.
• REMOVE DRYWALL CEILING WHERE INDICATED. REMOVE INTEGRAL CEILING LIGHT FIXTURES.REFER TO MEP DEMOLITION DRAWINGS FOR ADDITIONAL INFORMATION.
• COORDINATE REMOVAL AND HANDLING OF EXISTING MOVABLE FURNISHINGS AND EQUIPMENT WITH OWNER.
• PORTIONS OF MECHANICAL PLUMBING, ELECTRICAL AND FIRE PROTECTION SYSTEMS REQUIRED TOMAINTAIN MINIMAL BUILDING LIFE SAFETY & FIRE PROTECTION SHALL REMAIN IN PLACE. GENERALCONTRACTOR TO COORDINATE WITH DEMOLITION SUB CONTRACTOR DURING BID PHASE.
• LAWFULLY DISPOSE OF ALL REMOVED ITEMS UNLESS OTHERWISE NOTED FOR SALVAGE OR REUSE.COORDINATE WITH OWNER FOR EXTENT OF DEMOLISHED ITEMS TO BE SALVAGED.
• UNLESS OTHERWISE NOTED, ALL EXISTING STAIR STRUCTURE & HANDRAILS TO REMAIN.
• FOR SPRINKLER DEMOLITION SEE MEP DRAWINGS.
• PROVIDE TEMPORARY SIGNAGE AT ALL DOORS PRIOR TO REMOVING EXISTING SIGNAGE.PRESERVE ROOM NUMBERS AND NAMES AT ALL LOCATIONS. MAINTAIN TEMPORARY SIGNAGE ATDOOR LOCATIONS UNTIL NEW SIGNAGE IS INSTALLED.
• REMOVE ALL WALL HUNG ART, PROTECT AND RELOCATE TO MAIN HOSPITAL BUILDING FORSTORAGE, COORDINATE WITH OWNER.
• REMOVE ALL WALL MOUNTED ITEMS (HOOKS, SHELVES, CLOCKS, BOARDS, ETC.) TO BE REMOVEDAND SALVAGED TO OWNER.
• PROVIDE CONTINUOUS PROTECTION TO ALL OCCUPIED SPACES TO PROHIBIT THE PASSAGE OFDUST AND DEBRIS DURING CONSTRUCTION, INCLUDING THE PROTECTION OF MECHANICALSYSTEMS.
• FIELD VERIFY HOARDING WALL LOCATIONS AND ACCCESS ENTRY INTO WORK AREA.
• ALL FINISHES TO REMAIN ARE TO BE PROTECTED AND RESTORED TO ORIGINAL CONDITION.
1100 Liberty AvenuePittsburgh, PA 15222T. +1 412 456 0900F. +1 412 456 0906
SEAL
DATENO.
KEY PLAN
Owner:
Structural:
Mechanical, Electrical, & Plumbing:
Food Service:
Code Consultant:
SCALE:
DRAWING TITLE:
PROJECT TITLE:
PROJECT No:
11/3
0/20
17 7
:30:
39 P
MC
:\RE
VIT
LO
CA
L\69
121_
BA
YC
RE
ST
_WA
GM
AN
_KIT
CH
EN
_R17
_m.c
lark
.rvt
1/8" = 1'-0"
BAYCREST HEALTH SCIENCES55 AMEER AVENUE,TORONTO, ONTARIO, MGA 2Z1
ENTUITIVE200 UNIVERSITY AVENUE, 7TH FLOOR,TORONTO, ONTARIO, M5H 3C6
H. H. ANGUS @ ASSOCIATES1127 LESLIE STREETTORONTO, ONTARIO, M3C 2J6
FOOD FACILITIES CONCEPTS, INC.1100 WASHINGTON AVE, SUITE 302CARNEGIE, PA 15106
JENSEN HUGHES2150 ISLINGTON AVE, SUITE 100TORONTO, ONTARIO, M9P 3V4
1 TYPICAL SUSPENDED LAY-IN CEILING SYSTEM DEMOLITION:-REMOVE SUSPENDED LAY-IN CEILING SYSTEM FROM WALL TO WALL, INCLUDINGTILES, GRID, PERIMETER TRACK AND HANGERS-REMOVE ALL LIGHT FIXTURES AND OTHER ELECTRICAL ITEMS-REMOVE ALL MECHANICAL DIFFUSERS, GRILLES, AND OTHER MECHANICALDEVICES-REMOVE ALL ACCESS PANELS AND CEILING ACCESSORIES-REFER TO MEP DEMOLITION DRAWINGS FOR COORDINATION AND ADDITIONALINFORMATION
2 EXISTING CEILING SYSTEM TO REMAIN, TYP. UNO3 EXISTING KITCHEN HOOD TO BE REMOVED.4 EXISTING GWB BULKHEAD TO REMAIN.5 DASHED LINE INDICATES APPROXIMATE LOCATION OF HOARDING WALL, TO BE VIF.
REFER TO DWG G-201 FOR PHASING.6 REMOVE COVE LIGHTING, EXISTING GWB COVE TO REMAIN7 REMOVE EXISTING LIGHT FIXTURE8 FIELD VERIFY PRIOR TO START OF WORK EXTENT OF CEILING WORK AND IMPACT
ON GYPSUM BD BULKHEAD AND COVE LIGHT. REMOVE ACT CEILING, LIGHTS, MECHDEVICES, SPRINKLERS, AND ANY OTHER CEILING ITEMS REQUIRED TOACCOMMODATE NEW WORK. SALVAGE ALL ITEMS TO BE REINSTALLED IN THE SAMELOCATION AFTER DEMOLITION WORK IS COMPLETE.
9 REMOVE ACT CEILING, LIGHTS, MECH DEVICES, SPRINKLERS, AND ANY OTHERCEILING ITEMS REQUIRED TO ACCOMMODATE ACCESS FOR NEW WORK. SALVAGEALL ITEMS TO BE REINSTALLED IN SAME LOCATION AFTER DEMOLITION WORK ISCOMPLETE.
10 REMOVE CONCRETE PANEL CEILING IN THIS AREA AS REQUIRED TO ACCOMMODATEACCESS FOR NEW WORK. SALVAGE ALL ITEMS TO BE REINSTALLED IN SAMELOCATION AFTER DEMOLITION WORK IS COMPLETE. PROVIDE TEMPORARYLIGHTING AS REQUIRED WHILE SPACE IS OCCUPIED DURING OPEN POOL HOURS.
11 REMOVE EXISTING COVE AND COVE LIGHTING.12 REMOVE CEILING COMPLETE INCLUDING LIGHTS, MECH DEVICES, AND ANY OTHER