209
BATTERY HOLDERS
AA CELL HOLDERS
No. BH3311
For (3) AA cell (UM-3)W/Cover Plus On-Off switch, 6” Lead Wire Connection
No. BH341
For (4) AA cell (UM-3)With Standard Snap Connection
No. BH3411
For (4) AA cell (UM-3)W/Cover Plus On-Off switch, 6” Lead Wire Connection
No. BH343
For (4) AA cell (UM-3)With Standard Snap Connection
No. BH344
For (4) AA cell (UM-3)With Solder Lug Connection
No. BH3611
For (6) AA cell (UM-3)With Snap Cover, 6” LeadWire Connection
No. BH362S
For (6) AA cell (UM-3)With Standard Snap Connection
No. BH363
For (6) AA cell (UM-3)With Standard Snap Connection
No. BH381M
For (8) AA cell (UM-3)With Solder Lug Connection And Mounting Ears
No. BH383
For (8) AA cell (UM-3)With Standard Snap Connection
No. BH3103
For (10) AA cell (UM-3)With Solder Lug Connection
210
BATTERY HOLDERS
No. BH411
For (1) AAA cell (UM-4)With Solder Lug Connection
No. BH411P
For (1) AAA cell (UM-4)With PC Board Mounting
No. BH421
For (2) AAA cell (UM-4)With Solder Lug Connection
No. BH4211
For (2) AAA cell (UM-4)With Cover Plus On-OffSwitch, 6” Lead Wire
No. BH431
For (3) AAA cell (UM-4)With Solder Lug Connection
No. BH4311
For (3) AAA cell (UM-4)With Cover Plus On-OffSwitch, 6” Lead Wire
No. BH441P
For (4) AAA cell (UM-4)With PC Board Mounting
No. BH441S
For (4) AAA cell (UM-4)With Standard Snap Connection
AAA CELL HOLDERS
No. BH421P
For (2) AAA cell (UM-4)With PC Board Mounting
211
BATTERY HOLDERS
AAA, N, 9V, 1/2 AA CELL HOLDERS
No. BH4411
For (4) AAA cell (UM-4)With Cover Plus On-OffSwitch, 6” Lead Wire
No. BH443
For (4) AAA cell (UM-4)With Solder Lug Connection
No. BH443S
For (4) AAA cell (UM-4)With Standard Snap Connection
No. BH511
For (1) N cell (UM-5)With Solder Lug Connection
No. BH511P
For (1) N cell (UM-5)With PC Board Mounting
No. BH521
For (2) N cell (UM-5)With Solder Lug Connection
No. BH102
For (1) 9 Volt batteryAluminum Holder With Solder Lug Cnnection
No. BH910
For (1) 9 Volt batteryWith Solder Lug Cnnection
No. BH980
For (1) 9 Volt batteryMetal Clip Holder
No. BH531
For (1) 1/2 AA (3.6V Lithium Battery)With PC Board Mountig
No. BH541
For (1) 1/2 AA (3.6V Lithium Battery)With Solder Lug Connection And Switch
212
No. BH2020
Coin cell Holder, For CR1220 &Other 12.5mm x 2mm Coin Cells, PCB Mount
No. BH2025
Coin cell Holder, For CR1225 &Other 12.5mm x 2.5mm Coin Cells, PCB Mount
No. BH2032
Coin cell Holder, For CR2032 &Other 20mm x 3.2mm Coin Cells, PCB Mount
No. BH2038
Coin cell Holder, For CR2325 &Other 23mm x 2.5mm Coin Cells, PCB Mount
BATTERY HOLDERS, SNAP COVERS
COIN CELL HOLDERS
No. BH2040
Vertical Coin cell Holder, For CR2032 &Other 20mm x 3.2mm Coin Cells PCB Mount
No. BC9 - 3” Leads, 5Pc. / Pk.No. BC100 - 10” Leads, 2Pc. / Pk.
9V Battery Snap, Vinyl Cover
No. BC109 - 6” Leads, 2Pc. / Pk
“T” Shape 9V Battery Snap, Vinyl Cover
No. BC120 - 6” Leads, 2Pc. / Pk
9V Battery Snap, Molded Plastic Cover
No. BH129 - 6” Leads, 2Pc. / Pk
“T” Shape 9V Battery Snap, Molded Plastic Cover
Male and female batttery snaps that mate with all of the battery holders and withstandard 9V batteries. 10” lead wire color coded to match polarity of 9V snap onbattery holder.
Philmore No. Description
No. BC7B MALE SNAP WITH 10”BLACK LEAD WIRE (BULK)
No. BC8B FEMALE SNAP WITH 10”RED LEAD WIRE (BULK)
No. BC6 2 PAIR OF MALE ANDFEMALE SNAP W/10”WIRE LEAD. (PACKAGED)
No. 2090 - Bulk PackedNo. 2090-25 - Display Package of 25
Fahnstock Clip3/4” Long, .144” Hole (No. 6) Brass Nickel Plated
213
TERMINAL BLOCKS & KNOBS
TERMINAL BLOCKSA terminal block designed to be end-stackable on a PC board so that thedesigner may have any number of contacts needed. The design providessecure wire protection for a broad range of wire sizes (up to 14 ga. max).The housing is molded of 94V-0 fire retardent plastic. Six pieces per pack-age; available in bulk, add “B” suffix to part number. (i.e. TB132B for Bulk)
Housing: Polymide 66 resin, blueTerminals: 0.9 x 0.9 Brass, tin platedScrews: M2.6 x 0.45P, steel, zinc platedWire cage: Brass, Nickle plated
Rated: 10 Amp. 300 VACTemperature rating: -55°C to + 125°CWire range: 14 AWG max.Dielectric Strength: 2000 VAC min.
for 1 minuteInsulation Resistance: 500 M ohm min.
at 500 VDCPitch: 5 mmNumber of pole: 2, 3
STRAIGHT TYPE RIGHT ANGLE TYPENo. TB132 - 2 Pos. Pkg./6 No. TB142 - 2 Pos. Pkg./6No. TB133 - 3 Pos. Pkg./6 N0. TB143 - 3 Pos. Pkg./6
Fluted with skirt indicator line on top .75” Dia., .50” High
Color: BlackNo. 3010
Fluted with taper skirt indicator line on top .94” Dia., .60” High
Color: BlackNo. 3035
Straight knurl with arrowhead indicator on top .82” Dia., .50” High
Color: Black with Aluminumtop inlay
No. 3055
Straight Knurl 0-9 num-bers on
aluminum skirt1.15” Dia., .70” High
Color: Black withAluminum top inlay
No. 3020
Straight knurl 0-10 num-bers on
aluminum skirt1.46” Dia., .60” High
Color: Black withAluminum top inlay
No. 3045
Control pointer knob withindicator line on top & side
1” Dia., .60” HighColor: BlackNo. 3050
Straight knurl pointer indi-cator line on side pointer
.54” Dia., .48” HighColor: Black with Aluminum
top inlayNo. 3060
Fluted grip with indicator line
Color: Black with Aluminumtop inlay
.60” Dia., .46” HighNo. 3025
.92” Dia., .62” HighNo.3030
Ribbed with skirt indicator line
Color: Black withAluminum top inlay.80” Dia., .67” High
No. 30151.35” Dia., .86” High
No.3040
KNOBSBlack bakelite material, brass insert for 1/4” shaft with set screw.
SPECIFICATIONS
Black pointer knob withindicator line. 1.25” long
No. 277AP
Straight knurl, aluminumskirt with black indicator
arrow. 1.375” DIA., .56” highColor; Black with aluminum
top inlay.No.337
For bulk pack add suffix letter “B”
Precision Tuning VERNIER DIAL CONTROL KNOBS
A vernier dial control knob will provide smooth andprecise tuning for either a potentiometer or variable capaci-tor. Planetary drive provides 8 to 1 ratio, allowing for veryfine adjustment of standard controls. The metal dial plate iscalibrated by etching and paint filling on brushed satin finishfor a very attractive appearance. Knob is calibrated over180 degrees of turn, reading from zero to maximum settingby clockwise rotation. Fits standard 1/4” control shafts andmounts on surface of cabinet or chassis. Very useful withany circuit where fine “tuning” is going to make life easier.
Part no. Diameter Calibration
S36 1 1/2” 0 to 10 S38 1-1/2” 0 to 100S50 2” 0 to 100
No. S50
Rear View
No. S36 No. S38
214
COOLING FANS
60 mm (2.36”) Square Cooling Fans
These cooling fans are quite popular in electronic equipment. They are available in several voltages and CFM( cubic feet per minute) air flow types. The fans have brushless DC motors which are polarity protected.
Specifications:
Motor: DC BrushlessCase & Impellers: 94V-0 PlasticOperating Temp.: -20o C - 80o C Ball Bearing
-10o C- 50o C Sleeve BearingLife Expectancy: 70,000 HoursUL, CUL, CSA Approvals
80 mm (3.15”) Square Cooling Fans
Specifications:
Motor: AC or DC BrushlessCase & Impellers: 94V-0 PlasticOperating Temp.: -20o C - 80o C Ball Bearing
-10o C- 50o C Sleeve BearingLife Expectancy: 70,000 HoursUL, CUL, CSA Approvals
40 mm (1.56”) Square Cooling Fans
These miniature cooling fans are quite popular in small electronic equipment including computers where heat is a problem or can causeproblems. The fans are available with brushless DC motors which are polarity protected.
Specifications:
Motor: DC BrushlessCase & Impeller: 94V-0 PlasticOperating Temp.: -20o C - 80o C Ball Bearing
-10o C- 50o C Sleeve BearingLife Expectancy: 70,000 HoursUL, CUL, CSA Approvals
120 mm (4.72”) Square Cooling Fans
Specifications:
Motor: AC or DC BrushlessCase & Impellers: 94V-0 PlasticOperating Temp.: -20o C - 80o C Ball Bearing
-10o C- 50o C Sleeve BearingLife Expectancy: 70,000 HoursUL, CUL, CSA Approvals
92 mm (3.62”) Square Cooling FansThese cooling fans are quite popular in electronic equipment including copiers, computers,
& data processing. They are available in several voltages and CFM (cubic feet per minute)air flow types. The fans are available with brushless DC or AC motors which are polarityprotected.
AMD K6-II CPU COOLING FAN
This CPU cooler is designed to fitthe AMD K6-II processor withspeeds up to 550MHz. Thedevice has low acoustical noise,quick easy installation, and a ballbearing motor.
No. 70-8156 AMD K6-II CPU Cooler
Part No.Thickness
mm
Speed
RPM
Max.
CFM
Noise
db
Bearing
StyleVoltage
Current
(ma)
70-4012 10 6500 7.7 29 Sleeve 12V DC 130
70-4128 10 6500 7.7 29 Ball 12V DC 130
Specifications:
Motor: DC BrushlessCase & Impeller: 94V-0 PlasticOperating Temp.: -20o C - 80o C Ball Bearing
-10o C- 50o C Sleeve BearingLife Expectancy: 70,000 HoursUL, CUL, CSA Approvals
Part No.Thickness
mm
Speed
RPM
Max.
CFM
Noise
db
Bearing
StyleVoltage
Current
(ma)
70-6128 15 3900 15 28 Ball 12V DC 140
70-6012 25 4000 24 29 Sleeve 12V DC 140
Part No.Thickness
mm
Speed
RPM
Max.
CFM
Noise
db
Bearing
StyleVoltage
Current
(ma)
70-8275 25 3200 29 34 Sleeve 12V DC 190
70-8128 25 3000 22 35 Ball 12V DC 120
70-6275 25 3000 24 28 Ball 120V DC 140
Features
>Fan size 50 x 50 x 10 mm
>Thermal interface: Chomerics T-725
>Operation Voltage: 7-12VDC
>Operating Current: 1.32W
>Noise Level: <30.4dB
>Rated Speed: 4800 RPM
>Air Flow: 11.5CFM
>Electrical Connection: 4 pin plug
>Dimensions w/ heat sink: 50x50x42mm
Part No.Thickness
mm
Speed
RPM
Max.
CFM
Noise
db
Bearing
StyleVoltage
Current
(ma)
70-8415 25 2400 69 35 Sleeve 12V DC 340
70-1128 25 3000 86 42 Ball 12V DC 240
70-1248 25 3000 86 42 Ball 24V DC 24070-6412 25 2900 105 33 Ball 120V DC 140
Part No.Thickness
mm
Speed
RPM
Max.
CFM
Noise
db
Bearing
StyleVoltage
Current
(ma)
70-8325 25 2400 36 39 Sleeve 12V DC 220
70-9128 25 3000 50 33 Ball 12V DC 180
70-6325 25 2900 31 30 Ball 120V DC 140
These cooling fans are quite popular in electronic equipment including copiers, and computers. They are available inseveral voltages and CFM ( cubic feet per minute) air flow types. The fans are available with brushless DC or AC motorswhich are polarity protected.
These cooling fans are quite popular in electronic equipment. They are available in several voltages and CFM ( cubic feet perminute) air flow types. The fans have brushless DC motors which are polarity protected.
Plastic Fan Filter Kits
These kits are designed to reduce noise, and remove impurities up to 45 PPI (Parts Per Inch). These kits consist of three parts. A Fan Guard,Media Filter, and a Retainer.
Specifications:
Guard;UL94V-0 PlasticUL .25 SpacingReduces Noise Level
Media Filter;PU (polyurethane) Foam45 PPIEasy Clean
Retainer;UL94V-0 PlasticLow Air ResistanceSnap-on Installation
Part Fan Size PPINumber (mm) Filtering
70-5340 40mm 4570-5360 60mm 4570-5380 80mm 4570-5392 92mm 4570-5312 120mm 45
Part Fan DimensionsNumber Size Dia. Mt. Centers
70-6340 40mm 1.24” 1.26”70-6360 60mm 1.97” 2.09”70-6280 80mm 2.81” 3.02”70-6330 92mm 3.25” 3.52”70-6415 120mm 4.125” 4.31”
Fan Guards
These guards are designed to fit the fans Philmore offers as well as other standard size models. They are to be used to keep foreign objectsfrom interfering with the operation of the fan as well as for safety purposes.
Specifications:
Nickel Chrome Steel WireWelded JointsMeets UL & CSA Standards
Fan Power Cords
These fan power cords fit Philmore models and other competitor fans with plug-in terminals. Philmore offers several configurations for yourconvenience.
No. 70-6420 - Straight 42” LongNo. 70-6424 - 90o 24” longNo. 70-6436 - 45o 36” long
No. 70-6420 No. 70-6424 No. 70-6436
COOLING FAN ACCESSORIES
215
No. 6092S
No. 1051B - BrownNo. 1051V - Ivory10A-250V15A-125VUL Approved
Non Polarized Plug
AC RUBBER ATTACHMENT PLUG BAKELITE FLAT GRIP CAP
With brass plated steel spring prongs. 15 Amps-125Volts. Cord hole .450”. Sturdy in construction. Canbe used for heavy duty work, as well as for regularcord sets.
No. 8901
JIFFY PLUG
No tools, no stripping. Perfect contact in 5 sec-onds. Cords extends from side of plug.
Non Polarized. Color: White
216
STRAIN RELIEFS & WIRE
HOOKUP or LEAD WIRE22 gauge, solid copper hookup wire with PVC insulation; UL list-ed 1007/1569. This is the standard at board level and also fits ourPrototype Boards, both solderless and solder types. Supplied in25 foot hanks in various colors and also in an assortment.
SPECIFICATIONS:UL 1007/1569
Insulation:.016” thk. PVC 105oC 300-volts nominal O.D. .0626”
No. 12-2211 - black No. 12-2214 - white No. 12-2216 - redNo. 12-2217 - greenNo. 12-2218 - yellowNo. 12-2276 - 5 piece kit, 1 each of 5 colors
MAGNET WIRE
Part No.
12-123412-123212-123012-122812-1226
AWGSize3432302826
Approx. Footageper 1/2 lb. spool
4050 feet2510 feet1640 feet1032 feet650 feet
Part No.
12-122412-122212-122012-121812-1216
AWGSize2422201816
Approx. Footageper 1/2 lb. spool
408 feet251 feet160 feet101 feet62 feet
Commonly used for winding R.F.coils and transformers and generallab or school classroom assembly.This is a standard round, pure cop-per wire with a polyimide enamelinner-coat and polyurethane overcoat; Thermo Class 130. The insu-lation will stand up and not crackduring winding of tight coils, highspeed winding etc..
UL Listed; Sizes for most popular AC power cords. Recognized under Component Program of Underwriters’Laboratories File No. E-10793. Certified by Canadian Standards Assoc. File No. LR-66162.This series of AC cord bushing provides the most accepted method of securing AC power cords at the point wherethey enter/exit the chassis or cabinet. These bushings are generally regarded as permanent and will prevent dam-age to the wire as well as securing the wire against any possible in-out motion.Select the type needed first by wire type and gauge and then the maximum panel thickness. In cases where thewire is a special, not listed in the chart, use the approximate wire size column.Molded of Nylon; the two pieces of these strain reliefs are permanently connected by an integral tether to preventthem from becoming separated.Part no. shown is for one package containing ten pieces. For bulk package add a “B” to the end of number andorder in standard package multiples of 50 pieces.
PartNumber
65-1000
65-1010
65-1015
65-1020
65-1025
65-1030
65-1035
65-1040
65-1045
65-1050
65-105565-1055
65-106065-1060
65-1070
Dim.D
.406”
.406”
.406”
.406”
.433”
.433”
.583”
.583”
.583”
.583”
.748”
.748”
.818”
Max.“Thk.F
.0625”
.098”
.0625”
.098”
.0625”
.098”
.0625”
.125”
.0625”
.125”
.063”
.125”
.125”
HoleB
.390”
.390”
.465”
.465”
.452”
.452”
.55”
.55”
.55”
.55”
.660”
.660”
.750”
HoleA
.433”
.433”
.5-.515”
.5-.515”
.5-.515”
.5-.515”
.625”
.625”
.625”
.625”
.780”
.750”
.780”
.750”
.750”
Approx.Wire Size
.118x.220”
.118x.220”
.150x.300”
.150x.300”
.25-.291”
.25-.291”
.30”
.30”
.320-.362”
.320-.362”
.433”.362-.413”
.433”.362-.413”
.472”-.598”
UL WireType
SPT-1
SPT-1
SPT-2
SPT-2
SVI SVT
SVI SVT
SJT-18/3
SJT-18/3
SJT-16/3
SJT-16/3
SJT-14/3SJT-14/3
SJT-14/3SJT-14/3
SJT-12/3
WireShape
Flat
Flat
Flat
Flat
Round
Round
Round
Round
Round
Round
RoundRound
RoundRound
Round
STRAIGHT-THROUGH STRAIN RELIEF BUSHINGS
Maximum Chassis ThicknessPart actually has
additional clearance.
Mounting Hole
STRAIN RELIEF TOOL No. 63-640
High quality assembly tool for Nylon strain reliefs. Adjustable for all Philmore & other Heyco- Type strain relief bushings, that assemble into holes up to 7/8” diameter. Spring loadedaction (replaces Philmore WS40).
PHILMORE STRAIN RELIEF TOOL
No. 63-640
217
SPECIFICATIONS
STRANDED TINNED COPPER
PVC INSULATION (10 COLORS) .016”
UL STYLE 1007/1569 VM-1
CSA TR-64
TEMPERATURE -40 to 105° C.
Rated 300 volts
Philmore Hook-up WireUL Style 1007/1569
Insulated copper wireSolid and stranded types.
Philmore offers all of the most called for gauges in UL listed, 300
volt hook-up wire for use in electronic and electrical circuits. Ten col-
ors in wire gauges 26 through 16 AWG and your choice of 25 or 100
foot spools.
Color 25 ft. Spool 100 ft.
Spool
Black 78-22610 78-22640
Brown 78-22611 78-22641
Red 78-22612 78-22642
Orange 78-22613 78-22643
Yellow 78-22614 78-22644
Green 78-22615 78-22645
Blue 78-22616 78-22646
Violet 78-22617 78-22647
Gray 78-22618 78-22648
White. 78-22619 78-22649
26 AWG STRANDED .051 nom.OD 7X34 strands
Color 25 ft. Spool 100 ft.
Spool
Black 78-22410 78-22440
Brown 78-22411 78-22441
Red 78-22412 78-22442
Orange 78-22413 78-22443
Yellow 78-22414 78-22444
Green 78-22415 78-22445
Blue 78-22416 78-22446
Violet 78-22417 78-22447
Gray 78-22418 78-22448
White. 78-22419 78-22449
24 AWG STRANDED .056 nom.OD 7X34 strands
Color 25 ft. Spool 100 ft.
Spool
Black 78-22210 78-22240
Brown 78-22211 78-22241
Red 78-22212 78-22242
Orange 78-22213 78-22243
Yellow 78-22214 78-22244
Green 78-22215 78-22245
Blue 78-22216 78-22246
Violet 78-22217 78-22247
Gray 78-22218 78-22248
White. 78-22219 78-22249
22 AWG STRANDED .062” nom.OD 7X30 strands
Color 25 ft. Spool 100 ft.
Spool
Black 78-22010 78-22040
Brown 78-22011 78-22041
Red 78-22012 78-22042
Orange 78-22013 78-22043
Yellow 78-22014 78-22044
Green 78-22015 78-22045
Blue 78-22016 78-22046
Violet 78-22017 78-22047
Gray 78-22018 78-22048
White. 78-22019 78-22049
20 AWG STRANDED .069” nom.OD 10X30 strands
Color 25 ft. Spool 100 ft.
Spool
Black 78-21810 78-21840
Brown 78-21811 78-21841
Red 78-21812 78-21842
Orange 78-21813 78-21843
Yellow 78-21814 78-21844
Green 78-21815 78-21845
Blue 78-21816 78-21846
Violet 78-21817 78-21847
Gray 78-21818 78-21848
White. 78-21819 78-21849
18 AWG STRANDED .077” nom.OD 16X30 strands
Color 25 ft. Spool 100 ft.
Spool
Black 78-21610 78-21640
Brown 78-21611 78-21641
Red 78-21612 78-21642
Orange 78-21613 78-21643
Yellow 78-21614 78-21644
Green 78-21615 78-21645
Blue 78-21616 78-21646
Violet 78-21617 78-21647
Gray 78-21618 78-21648
White. 78-21619 78-21649
16 AWG STRANDED .092” nom.OD 26X30 strands
HOOK - UP WIRE
Color 25 ft. Spool 100 ft.
Spool
Black 78-12410 78-12440
Brown 78-12411 78-12441
Red 78-12412 78-12442
Orange 78-12413 78-12443
Yellow 78-12414 78-12444
Green 78-12415 78-12445
Blue 78-12416 78-12446
Violet 78-12417 78-12447
Gray 78-12418 78-12448
White. 78-12419 78-12449
24 AWG SOLID Copper insulated
SPECIFICATIONS
SOLID COPPER
PVC INSULATION (10 COLORS)
.016” Insulation thickness
UL STYLE 1007/1569 VM-1
CSA TR-64
TEMPERATURE -40 to 105° C.
Rated 300 volts
Color 25 ft. Spool 100 ft.
Spool
Black 78-12210 78-12240
Brown 78-12211 78-12241
Red 78-12212 78-12242
Orange 78-12213 78-12243
Yellow 78-12214 78-12244
Green 78-12215 78-12245
Blue 78-12216 78-12246
Violet 78-12217 78-12247
Gray 78-12218 78-12248
White. 78-12219 78-12249
22 AWG SOLID Copper insulated
Color 25 ft. Spool 100 ft.
Spool
Black 78-12010 78-12040
Brown 78-12011 78-12041
Red 78-12012 78-12042
Orange 78-12013 78-12043
Yellow 78-12014 78-12044
Green 78-12015 78-12045
Blue 78-12016 78-12046
Violet 78-12017 78-12047
Gray 78-12018 78-12048
White. 78-12019 78-12049
20 AWG SOLID Copper insulated
Color 25 ft. Spool 100 ft.
Spool
Black 78-11810 78-11840
Brown 78-11811 78-11841
Red 78-11812 78-11842
Orange 78-11813 78-11843
Yellow 78-11814 78-11844
Green 78-11815 78-11845
Blue 78-11816 78-11846
Violet 78-11817 78-11847
Gray 78-11818 78-11848
White. 78-11819 78-11849
18 AWG SOLID Copper insulated
218
CORDS AC & POWER
A standard insulated, two conductor cord with a rib on one conductor for polarity indication. Available in popular colors. The 25 foot
lengths are supplied in blister display packages. The longer lengths are supplied on spools with a clear, protective shrink-wrap.
SPT cord sets are typically used in light duty appli-
cations, such as table radios, household lamps and
so forth. SPT cords are two conductor, 18 gauge.
SJT cord sets are three conductor, counting the
ground wire, and regarded as hard service cord sets,
frequently used with bench tools such as grinders,
saws etc.. This is a popular cord set for equipment of
all kinds. SJT cord sets are supplied with a standard
NEMA 5-15P power plug. Both of these series are of
fully molded construction, the plug and cord are per-
manently connected.
A direct replacement for the new Panasonic Cassette Recorders, as well as for other
recorders and many portable TV sets. Mates with male receptacles having 3/32” diameter
pins on 0.275” centers. Rated 7 amps at 125V AC, this cord set is UL Approved. 6 feet long.
Top: SPT Type AC Cords
Bottom: SJT Type AC Cords
SPECIFICATIONS:AWG Gauge: 18 Gauge copper
Stranding: 41 strands/ 34 Gauge
Insulation Thickness: 0.030”
Insulation Material: PVC
Working Voltage: 300V AC
Temperature Range: 105oC
Size:Nominal O.D.: 2.65 x 5.35mm or
.104” x .210”
UL Listed CSA Approved
18 AWG SPT-1 PARALLEL POWER CORD UL listed
AC POWER CORD SETS for OEM and Replacements
AC CORD SET - for Cassette Recorders
COLOR
Black
Brown
White
25 ft.
48-14248-14448-146
100 ft.
48-10248-10448-106
250 ft.
48-25248-25448-256
1000 ft.
48-100248-100448-1006
2000 ft.
48-200248-200448-2006
Part No.
SPT1182-6BL
SPT1182-6BR
SPT1182-6WH
SPT1182-9BL
SPT1182-9BR
SJT143-3
SJT143-6
SJT163-3
SJT163-6
SJT163-9
SJT183-6
SJT183-9
UL Wire Type
SPT-1
SPT-1
SPT-1
SPT-1
SPT-1
SJT
SJT
SJT
SJT
SJT
SJT
SJT
Wire Gauge
18 x 2
18 x 2
18 x 2
18 x 2
18 x 2
14 X 3
14 x 3
16 x 3
16 x 3
16 x 3
18 x 3
18 x 3
Length
6 ft.
6 ft.
6 ft.
9 ft.
9 ft.
3 ft.
6 ft.
3 ft.
6 ft.
9 ft.
6 ft.
9 ft.
Color
Black
Brown
White
Black
Brown
Black
Black
Black
Black
Black
Black
Black
Amps
10
10
10
10
10
15
15
15
13
13
10
10
No. 2464PNo. 2464PB bulk packaged
No. 2465P - Replacement power cord for
Sony recorders and boom boxes
No. 2465PB bulk packaged
No. 2465PNo. 2464P
219
TWIST-ON WIRE CONNECTORS
Molded of rugged, impact and heat resistant plastic. Color identifies size. Heavy ribbed bodies for easy gripping. Display package of 10.
No. WN66 - Large - redNo. WN66B - bulkWire size: #18 to #10Rating: 600v/ Building wire,1000v/ Signs & Fixtures
No. WN33 - Small - orangeNo. WN33B - bulkWire Sizes: #18 to #16Rating: 300V/Building wire,300v/Signs & Fixtures
No. WN44 - Medium - yellowNo. WN44B - bulkWIRE SIZES: #18 to #12Rating: 600v/ Building wire,1000v/ Signs & Fixtures
UL Listed
REPLACEMENT AC PLUGS
Black; Solder Terminals
No. 8464
No. 8466
No. 8465
VINYL PLASTIC
ELECTRICAL TAPE
UL LISTED
66 ft. rolls x 3/4” wide,black vinyl tape, witha dielectric strength of12,000 volts, and ten-sile strength of 15 lbs.per inch. Thickness 7-9 mils. Flexiblestretch, waterproof, and will resist oil, gaso-line, salt water, alkalis, and sunlight.
No. PT2
No. PT2B -bulk packaged
AC CONNECTORS
The LKG Wire Knutt, A push - in wire connector, fast, alternative to wire nuts.The LKG Wire Knutt accommodate wire sizes from 22 to 12 AWG (solid conductors). Fast assembly! Strip wire (0.43” or 11 mm strip length) andpush it into the knutt. Fast and secure; use in machinery, house wiring etc. for fast and secure connection of wires of same size or various sizes.Available in sizes for joining from two to eight wires.
Specification:
Housing Material: Thermoplastic, UL 94V-2 flame retardentCurrent: 24A (VDE)Voltage: UL-600V, VDE-450V.Temperature Rating: 110ºCUL file No.: E - 113650
65-25265-253 65-254 65-255
65-258
UL Approved
No. R118J
CONVENIENCE RECEPTACLE
Suitable for accessory equipment power out-lets on amplifiers, pre-amplifiers, clock radiochassis, etc. Requires 1-1/16” x 7/16” rec-tangular cutout.Non Polarized Receptacle.
Part No. Color Wires
65-252 RED 2
65-253 ORANGE 3
65-254 YELLOW 465-255 GREY 565-258 BLACK 8
Panel mount 3 prong grounding receptacles, snap-in type, rated at 15A - 125VAC, UL approved. Black plastic.
AC Receptacles
No. 8535 - .250” Male Quick connector solder terminal
No. 8540 - .250” Female Quick connectterminal with wire protector
No. 8545 - 6” - 16 awg. wire leads terminal
(mounting hole: 0.96” x 0.87”) (mounting hole: 1.18” x 0.94”) (mounting hole: 1.18” x 0.94”)
C US
220
AC CONNECTORS
DEAD FRONT GROUNDING CAP
UL Listed & CSA Approved
No. 8515P
No. 8901
No. 6092S
No. 1051B - BrownNo. 1051V - Ivory10A-250V15A-125VUL ApprovedNon Polarized Plug
No. 8147V IvoryNo. 8147B Brown
No. 8419
No. 8400
UL and CSA Approved. This three-prong AC plugcan take wires up to #12. Removable insert used forthinner wire. Steel armor clad. New dead front design completely encloses thehousing, eliminating need for insulator and insuringagainst accidental short circuit.
RUBBER AC 3 WIRE PLUG
UL Listed & CSA Approved
No. 8520
For .225” - .600” cord rubber plugs and femalereceptacles resist chemical and petroleum by-prod-ucts. Have low temperature flexibility and resist highheat.
3 WIRE FEMALE CONNECTOR
OFFICE EQUIPMENTAC CONVERTER (IEC STANDARD)
JIFFY PLUG
AC RUBBER ATTACHMENT PLUG
BAKELITE FLAT GRIP CAP
TRIPLE GROUNDING TAP
PARALLEL GROUNDING ADAPTOR
VINYL CUBE TAP
Three prong power cord connector (like industry typeIEC320-13) used on nearly all personal computers,printers, copy machines and other office equipment. No. 8522 In-Line Female (Rated 10A @ 250VAC)No. 8922 - Right Angle In-Line Female
(Rated 10 @ 250 VAC)No. 8523 In-Line Male (Rated 10A @ 250VAC)No. 8923 - Right Angle In-Line Male
(Rated 10A @ 250 VAC)No. 8527 Panel Mount Male, Snap-In Type.
(Rated 15A @ 250VAC)No. 8529 Panel Mount Male, Screw Mt. Type
(Rated 15A @ 250VAC)
Accepts 3 standard grounding plugs into a singlegrounding outlet. Ample room even for right angletype plug.Size of bakelite case: 3” x 1-3/32” x 1” deep.
Convert three-prong to two-prong caps. Polarizedblades and rigid grounding lug. Compact designextends only 1” from socket.
Heavy-duty, durable brown cube tap. One-piececonstruction. Brass spring prongs. Rated: 15A - 125V
No tools, no stripping. Perfect contact in 5 seconds.Cords extends from side of plug.
Non Polarized. Color: White
With brass plated steel spring prongs. 15 Amps-125Volts. Cord hole .450”. Sturdy in construction. Canbe used for heavy duty work, as well as for regularcord sets.
UL Listed & CSA Approved
No. 8525For .225” - .600 cord.
ARMORED GROUNDING CONNECTOR
3-Contact AC Female Receptacle with Removable Cord Clamp
This yellow vinyl connector mates with our No.8515P dead front grounding cap. It takes 3 #12wires. Each circuit is separated by vinyl divider.Uses heavy duty, double wipes contacts. UL Listedand CSA Approved.
No. 8515J
Hospital Grade AC PLUG and CONNECTOR
Figure 1 Figure 2
A.C. power connectors meeting all federal specifi-cations for hospital use, as required by the NationalElectric Code (article 517). Verified by UL to latestfederal specifications. Both devices feature termi-nals separated by insulating barriers, captivespeed-screws assembly and integral strain relief.Both accommodate cords with an O.D. from .250” to.685”. The connector configuration is NEMA 5-15and rated at 15 amps at 125 volts AC.fig. 1 No. 8266 - male plugfig. 2 No. 8269 - connector
15A 125VNEMA 5-15
No. 8522
No. 8523
No. 8527
No. 8529
No. 8922
No. 8923
221
MULTITESTERS / CIRCUIT TESTERS
HI-VOLTAGE TESTING SCREWDRIVER
No. 903-150N
SPECIFICATIONS: 2000 OHMS--VOM
6 to 12 VOLT CIRCUIT TESTERwith HEAVY DUTY PROBE
DIGITAL MULTI-TESTER
TEST LIGHT
No. P5120For testing 80-250 Volts AC or DC. This handy combination screwdriver/testeris used for testing ground lines, open or shorted circuits.
No. P5128For testing all 6V and 12V systems: Auto, RV, Marine, Aircraft etc..Quickly finds short, grounds and open circuit.
No. P5100For testing 80-500 Volts AC or DC. The 5” insulated leads with finger guardinsulated tips make testing electrical circuits safe and easy. Red neon bulbglows with increasing intensity with increased voltage.
DISPLAYOVERRANGE INDICATIONMAXIMUM COMMON MODEVOLTAGEOPERATING ENVIRONMENT
STORAGE ENVIRONMENTTEMPERATURE COEFFICIENT
POWERBATTERY LIFE
DIMENSIONS
3 1/2 digit LCD .5” height, with polarity.3 least significant digits blanked
500V peak.0 to 50 C, less than 80% relative humidity up to 35º C,less than 70% relative humidity from 35º C to 50º C.-15º C to 50º C(0 to 18 C, 28 to 50), less than 0.1x applicable accuracy specification per C.9V alkaline or carbon-zinc battery (NEDA 1604)100 hours typical with carbon-zinc cells, 200 hours with alkaline cells.126mm long x 70mm wide x 24mm thick.(4.96”x2.76”x0.94”) Net weight 170g (6 oz)
Specifications:
Slip Grip Test Leads, Battery and Instructions are included
Sensitivity:DC Volt Ranges:
DC Current Ranges:AC Volt Ranges:
Resistances Ranges:Accuracy:
2000 ohms/volt2.5-10-50-500-1000.5-10-250ma.10-50-500-10005K-50K-500K3%DC, 4%AC
HIGHER PERFORMANCE POCKET MULTITESTER
No. UM22
Plastic test prod handles, 4” long, 3/8” diameter, with prods 1” long. Redand Black. Equipped with 48” kinkless plastic-covered leads .135” O.D.Available with either insulated banana plugs or phone tips at other end,to fit standard American jacks.
TEST LEADS
No. 466
Phone Tips
No. 467
Banana Plugs
Two 42” flexible, vinyl-covered test leads, heavily insulated toprevent high voltage breakdown and cut-through. 80 -strandcopper conductors eliminate wire fatigue and assure long life.Equipped with adaptor accessories most often used by ser-vicemen, this kit can perform virtually every test requirement.Each lead is attached to a 4-3/4” probe (1-red, 1-black).Banana plugs on each end have nickel-plated phosphorbronze springs to maintain rigid contact through many thou-sands of insertions. Heavy plated BRASS Adaptors-Color-coded Spade Lugs*-large enough for lab. instruments (up to1/4” dia. center post). Test prod phone tips(0.180” dia.)Strong spring action alligator clips. NP phone tips.-notinsulated. Each insulated adaptor completely covers bananaplugs to eliminate accidental contact, avoiding shorts.
DELUXE UNIVERSAL SOLDERLESS TESTLEAD SET
No. SA15
TOOLS
10 pc. TOOL SETA tool for all applications for trimmer adjustments. Set
includes square tips, hex tips, different size screwdriver
blades and recessed blades. Manufactured with tough cel-
con material.
No. 63-910
10 PIECE ELECTRONIC COMBINATION WRENCH SET
This fine quality set of 10
combination wrenches is
excellent for electronic repair
and service. The size and
thickness are especially suit-
ed for technician needs.
The wrenches are the follow-
ing sizes: 5/32”, 3/16”, 1/4”,
7/32”, 15/64”, 5/16”, 9/32”,
3/8”, 11/32”, and 7/16”. All
are hot forged and chrome
plated.No. 63-608
ALIGNMENT TOOLS
MINIATURE POTENTIOMETER, “TRIMPOT” TOOL
One end is a recessed blade for non-slip adjustment of miniature
potentiometers that have a protruding adjustment screw. The other
end has a protruding metal blade for pots with flush screw-slot
adjustment. Small steel tips have negligible flux-effect: body is
molded of anti-static plastic. Replaces types 8608, AS8608.
No. 63-8608
SQUARE and HEX ALIGNMENT TOOLSquare: .060” Hex: 0.10”
A double-ended, anti-static alignment tool for ferrite core trans-
formers. One end is a square .060” Tip with an additional protrud-
ing flat (.024” thick) blade. The other end is a 0.10” hex with a pro-
truding (.039” thick) blade. Replaces types 9440 and AS9440..
No. 63-9440
STEEL TIP DUAL ALIGNMENT TOOL
Recessed steel tip one end, protruding steel tip on the other. Tool
shaft dia. 7/32” (5.5mm). The recessed tip fits a no.6 slotted shaft
common to many I.F. transformers. The protruding tip is .130” wide
and protrudes .190”. Molded of anti-static material. Replaces types
8276 and AS8276.
No. 63-8276
DOUBLE HEX ALIGNMENT TOOL
A broad usage tool with stepped .078” hex and 0.10” hex on one
end, preceded by a fine .020” x .065” flat blade. The opposite end
is a 0.10” hex preceded by a .030” x .10” flat blade. Overall length
is 7-9/16”, molded of durable Nylon.
No. 63-9297
LONG REACH ALIGNER, WITH HANDLE
A plastic alignment tool with a 0.02” x .080” steel tip. Length of
shaft from tip to handle is 5-3/4”. overall tool length is 7-7/8”. Shaft
is somewhat flexible for tight spots; handle provides better grip
than regular alignment tools.
No. 63-5001
DOUBLE 078 HEX ALIGNERHEX: .078”
A Nylon tool .078” hex on both ends; one end undercut for reach-
ing through to a bottom slug, the other with a stop to prevent over-
reaching. Replaces type 9300.
No. 63-9300
222
223
TOOLS
ALIGNMENT TOOLSSPECIAL HEX-TIP TOOL
Hex: 0.10”
On one end, flat tip (0.025” thick x 0.10” wide) is followed by a
0.10” hex. The opposite end is an undercut 0.10” hex. Overall
length, 5”. Replaces type 8606.
No. 63-8606
DOUBLE END HEX TOOLHex: .125”
One end is an under cut .125” and other is a .125” hex preceeded
by a flat (.025” thick x .10” wide) blade. Entire tool is molded
Nylon. Replaces type 9091.
No. 63-9091
SCREWDRIVER-HEX COMBINATION TOOLHex: .078”
One end is an undercut 0.078” hex tip and other is a screwdriver
style tip that is 0.10” in diameter and tapers to 0.015” thick. Overall
length: 5-5/16”, molded Nylon. Replaces type 9304.
No. 63-9304
SCREWDRIVER-HEX COMBINATION TOOLHex: .092”
One end is an undercut 0.092” hex tip and other is a screwdriver
style tip that is 0.10” in diameter and tapers to 0.015” thick. Overall
length: 5-5/16”, molded Nylon. Replaces type 8282.
No. 63-8282
TELEVISION ALIGNMENT TOOL SET
Kit contains the five most commonly needed tools for television
service. Also included is an extender that may be used as an
extension handle when a longer reach tool is needed. Kit is sup-
plied in a segmented pouch to keep tools together.
Contains: 63-9300 63-860663-8282 63-909163-9304 Extender
No. 63-8454
SQUARE and HEX ALIGNMENT TOOLSquare: .060” Hex: 0.10” & Blade
A double-ended, molded nylon tool: overall length is 4-3/4” One
end is a square .060” tip with protruding blade from a 0.10” hex.
The other end is a flat (.039” thick) blade which is followed by an
undercut .10” hex. A tool frequently needed in color copier mainte-
nance
No. 63-9442
DOUBLE ENDED HEX TOOLHex: 0.078”
Undercut .078” hex on one end and on the other the hex is
stopped with a larger diameter shaft. Overall length is 5.33”.
Molded Nylon.
No. 63-9301
DOUBLE ENDED HEX TOOLHex: 0.10” & .087”
A dual ended tool with an undercut 0.10” hex on one end and a
standard .087” (for 2.2mm cores) hex on the other. Overall length
is 5.6”. Molded Nylon.
No. 63-8603
TECH’S ALIGNMENT TOOL KITA general purpose kit containing four tools with a variety of need-
ed tips. Includes tools for most common ferrite core adjustments
used in today’s circuits. Supplied in a plastic pouch. Contains tool
Nos.: 63-8603, 63-9301, 63-9442, and 63-9297.
No. 63-8420
224
TOOLS
20-pc. PERSONAL COMPUTER TOOL KITDELUXE TOOL KIT for complete field service work. Contains all the tools you need to
add or remove parts, peripherals and printed circuit boards. All packaged in deluxe
black vinyl zipper case (13” x 7-1/4” x 1-3/4”) folded size.
CONTENTS:1/4” nut driver • 3/16” nut driver #0 Phillips screwdriver
#1 Phillips screwdriver • 1/8” std. screwdriver
3/16” std. screwdriver • T-10 torx driver • T-15 torx driver • Mini long-nose plier
6” adjustable wrench • 4-3/4” long tweezer • 3-prong parts holder • 30W soldering iron •
Desolder pump • Rosin core solder • Brush Anti-static wrist strap • I.C. insertion tool •
I.C. extractor tool
7-1/4” 4-way crimper
PERSONAL COMPUTER TOOL KITA complete kit for servicing plus adding peripherals and printed circuit boards to your PC. In
addition to being heat treated, these tools are shot peened, making them extra tough so as to
avoid chipping and distortion.
The IC extractor, tweezer and retriever are fully insulated. Each tool handle is shaped for com-
fort while designed to give more power and extra torque.
The feature of the torx driver is its reversible bit having two sizes on a single handle: T-10 and
T-15.
THE KIT HAS:1/4” nut driver • 3/16” nut driver • 3-prong parts retriever/extractor
• 4-5/8” long assembly tweezer • T-10/T-15 reversible torx driver • 14-16 Pin I.C. Inserter
• #1 Phillips screwdriver, 6” overall • 3/16” slotted screwdriver, 6” overall
• Integrated circuit extractor • #0 Phillips screwdriver, 5-1/2” overall
1/8” slotted screwdriver, 5-1/2” overall
These tools are neatly secured in elastic straps enclosed in a compact, padded vinyl zipper
case.
No. CT225
5 PIECE CHASSIS PUNCH SET
No. 110EComplete set of punch-
es in a leatherette car-
rying case. All precision
machined of top grade
steel. Following sizes:
5/8”, 11/16”, 3/4”, 1”, 1-
3/16”, plus burring
reamer. (.47”)
IDC CRIMPING TOOL
No. HT214R - Replacement Crimping Block
This all-steel construction tool with cushioned handle grips provides
good short run production capabilities for all insulation displacement
connector assembling. Works for D-Sub and Centronics.
No. HT214
No. CT813
COAXIAL TOOL KITS
All the tools needed to cut, strip and install RG58, RG59, RG62 (Tool
Kit No. WS600) plus RG6 (Tool Kit No. WS604) and center pin in a
convenient storage and carrying case.
Tool KIt No. WS600 (for RG58, RG59 & RG62)
Includes:
(Fig. 1) No. WS28 (Ratchet Crimp Tool)
(Fig. 2) No. WS145 (Stripping Tool)
(Fig. 3) No. WS50 (Cable Cutter)
Tool KIt No. WS604 (for RG58, RG59, RG62 & RG6)
Includes:
(Fig. 1) No. WS36 (Ratchet Crimp Tool)
(Fig. 2) No. WS145 (Stripping Tool)
(Fig. 3) No. WS50 (Cable Cutter)