1 SLAES DEPARTMENT | PICK_SIX_WONDER_CUTTING_GUIDE.INDD | 06-18-21 | v.1 “PICK SIX WONDER” CUTTING GUIDE GENERAL NOTES: • Start with 6 pieces of 6" x 6" or 15.2 x 15.2 cm Designer Series Paper (DSP) • Notice direction of DSP and match up with top of cutting guide • Repeat all cuts on all 6 DSP pieces Design 2: Trio of Rectangles (6 pieces) Design 4: Hearts (6 pieces make 3 cards) Design 3: 3 pieces/3 belly bands (+1 additional card: use 3 leftover pieces cut in half) Design 3: 6 pieces/3 tops and 3 bottoms (6+3 = 9 pieces make 3 cards) Design 2: Trio of Rectangles (6 pieces) (6+6 = 12 pieces make 4 cards) Design 1: Cubes (6 pieces make 3 cards) Cut a slit 1-1/4" (3.1 cm) at and to halfway mark 2-1/2" (6.2 cm ) 2-1/2" (6.2 cm ) 3-1/2" (9 cm) 3-1/2" (9 cm) 1-3/4" (4.5 cm) 1-3/4" (4.5 cm) 2-1/2" (6.2 cm) 2-3/4" (7 cm) 2-1/2" (6.2 cm) 3/4" (2 cm)
Transcript
1
SLAE
S DE
PART
MEN
T | P
ICK_
SIX_
WO
NDER
_CUT
TING
_GUI
DE.IN
DD | 0
6-18
-21 |
v.1 “PICK SIX WONDER” CUTTING GUIDE
GENERAL NOTES: • Start with 6 pieces of 6" x 6" or 15.2 x 15.2 cm Designer Series Paper (DSP)
• Notice direction of DSP and match up with top of cutting guide
• Repeat all cuts on all 6 DSP pieces
Design 2: Trio of Rectangles(6 pieces)
Design 4: Hearts(6 pieces make 3 cards)
Design 3: 3 pieces/3 belly bands(+1 additional card: use 3 leftover pieces cut in half)
Design 3: 6 pieces/3 tops and 3 bottoms (6+3 = 9 pieces make 3 cards)
Design 2: Trio of Rectangles(6 pieces)
(6+6 = 12 pieces make 4 cards)
Design 1: Cubes(6 pieces make 3 cards)
Cut a slit 1-1/4" (3.1 cm)at and to halfway mark
2-1/2" (6.2 cm )
2-1/2" (6.2 cm )
3-1/2" (9 cm)
3-1/2" (9 cm)
1-3/4"(4.5 cm)
1-3/4"(4.5 cm)
2-1/2"(6.2 cm)
2-3/4"(7 cm)
2-1/2"(6.2 cm)
3/4"(2 cm)
2
SLAE
S DE
PART
MEN
T | P
ICK_
SIX_
WO
NDER
_CUT
TING
_GUI
DE.IN
DD | 0
6-18
-21 |
v.1“PICK SIX WONDER” INSTRUCTIONS
DESIGN 1: CUBES (3 CARDS)• From left edge, cut DSP at 2-1/2" or 6.2 cm
• Cut again at 2-1/2" or 6.2 cm from bottom
• Cut a slit at 1-1/4"or 3.1 cm from the center of the cube—just over halfway
• 6 pieces; mix and match patterns and separate into pairs
• Using slits, slide 2 cubes together
• Fold back 2 flaps and adhere
• If the cubes aren’t the same size, trim the edges
DESIGN 2: TRIO OF RECTANGLES (4 CARDS)• Cut remaining section in half—at 1-3/4" or 4.5 cm
• 12 pieces; mix and match patterns and separate into trios
• Adhere to cards
DESIGN 3: TOP, BOTTOM, AND BELLY BAND (3 CARDS)• On second piece, with a 3-1/2" or 9 cm width, from bottom edge, cut at 2-1/2" or 6.2 cm and again at 3/4" or 2 cm
• 6 large pieces; mix and match patterns and separate into pairs to make 3 cards
• Mix and match patterns and create 3 belly bands (use remaining 3 pieces for additional card; see below)
• Adhere to cards
DESIGN 3+: ADDITIONAL CARD (1 CARD)• Cut the 3 remaining 3-1/2" x 3/4" or 9 x 2 cm pieces (left over from design above), in half
• Mix and match patterns and adhere pieces to card
DESIGN 4: HEARTS (3 CARDS)• You have 6 pieces (2-3/4" or 7 cm) left
• Select 3 pieces for background
• Mix and match remaining three pieces for hearts
• Fold in half
• Cut a symmetrical heart, then cut another heart from the middle of the first heart
• Flip the mini heart and re-insert into bigger one
• Adhere pieces to cards
GREETINGS AND EMBELLISHMENTS (ALL CARDS)• Stamp, punch, and adhere preferred greetings to cards
