Date post: | 24-Apr-2015 |
Category: |
Documents |
Upload: | ragnar7052 |
View: | 96 times |
Download: | 12 times |
Pioneer PlasmaScan Board & IC Troubleshooting
Scan IC Removal & Reinstallation Guide
Technical Training Department1925 E. Dominguez StreetLong Beach, CA 90810
Contents
Topic PageChecking drives and Scan IC’s
4~5
Removing and reinstalling scan IC’s using nozzle type soldering station
6
Removing and reinstalling scan IC’s using Chipquick
7
Removing blue glue from scan IC’s
8~10
Blue glue model list 11
3
4
5
How to replace the SCAN ICs
There are two possiblities:- with a nozzle type soldering station- with the CHIPQUICK SMD1 removal kit
With nozzle type desoldering station
Work ESD safe
Solder all pins and check very carefully for dry joints
or short circuits
6
Once the IC is positioned,tip it diagonal so it cannot
move anymore
5
Remove IC and clean PCB.Check PCB for damaged
patterns and short-circuits.
4
Heat up all pins withthe nozzle.When solder reflows,remove IC with pick up tool
3
Add solder to all pinsof the defective SCAN IC
2
Mount the right type of nozzle
1
6
Clean site with swab dipped in flux while
applying heat.
Another way to remove SMDs is with a special solder made by Chip Quik.The solder is an alloy of tin, lead, indium,and bismuth. Bismuth has a very low thermal conductivity. If it is mixed with tin, the melting point is reduced to 65°C.and so it becomes difficult to damage the PCB . Another advantage is that there is no additional desolder equipmentrequired.It can be ordered with part number SMD1. This package contains chipquick flux , chipquick solder and alcoholpads.
6
7
1 2 3
4 5
Apply flux to all pins of thedefective SCAN IC
Adjust the temperature of thesolder iron to +/- 200°C and
melt CHIPQUICK alloyuniformly on all pins.
Maintain the alloy in moltenstate and remove the SCAN IC
with a pick - up tool.
Move the excess with the solderiron to an unused section of the
PCB. Remove after it's cooleddown.
At room temperature, clean theresidue with alcohol pad.
PCB is ready to mount the newSCAN IC.
With Chipquick
7
SERVICE KNOWHOW
Date: Sep.14, 2004 No.: SKD04003 MODEL No. See page 9 SUBJECT 1 How to remove the coating of SCAN IC.
[ Required equipment ]tweezers ( Curved Tip Tweezers are better than stright ones. )cutting pliers
[ Procedure ] 1. Peel the coating a little at the lower left corner of the SCAN IC which has rather more coating. (be careful not to damage the pattern.)
2. Make a notch at the peeled coating.
8
3. Pick up the peeled coating by tweezers, and wind them around the point of the tweezers while rotating tweezers.
4. Peel off the coating while rotating tweezers along the SCAN IC.
5. After all the coating around the SCAN IC is peeled off continue to the next page.
9
10
MODEL No. MODEL No.
PDP-434PC/TAXQ PDP-504PC/TAXQPDP-434PE/WYVI6 PDP-504PE/WYVI6PDP-434PE/WYVI6XK PDP-504PE/WYVI6XKPDP-434PE/WYVIXK/1 PDP-504PE/WYVIXK/1PDP-434PG/TLDFR PDP-504PG/TLDFRPDP-434PU/TUCK PDP-504PU/TUCKPDP-434PU/TUCKXC PDP-504PU/TUCKXCPDP-434CMX/LUC PDP-504CMX/LUCPDP-43MXE1/LDFK PDP-50MXE1/LDFKPDP-43MXE1-S/LDFK PDP-50MXE1-S/LDFKPDP-43MXE1-S/TAXQ PDP-50MXE1-S/TAXQPDP-435PE/WYVI PDP-505PE/WYVIPDP-435PE/WYVIXK PDP-505PE/WYVIXK
PDP-5004/KUC
11