Pipe & Manhole Handling PRODUCT FEATURES: • When these high-strength, clamps are dropped over a pipe, they automatically clamp it. ¥ Outriggers stabilize the pipe during lift. ¥ No blocking is required. ¥ The operator only has to guide the clamp into place. ¥ Pipes can be handled quickly and efficiently when properly balanced. ¥ Excellent for cast iron, or steel pipe, as well as tubing and other cylindrical objects. ¥ Pipe grab sizes listed will handle: all classes in a category of ASA standard cast iron pipe; standard, extra strong, and double extra strong steel pipe (all have same O.D.). ¥ Designed and manufactured to ASME B30.20. 1. Lower the grab and place on pipe. As rope is loosened grab will open and seat on pipe. 2. Lift slowly with grab engaged to check for balance. 3. Ideally, lift should be level, but never exceed an angle of 15¡ . Decreasing the load by bumping or substantial imbalance can, under certain circumstances loosen the grip. Do not use in diameters other than those specified on nameplate. Cast Iron Steel Dimensions Rated Pipe Pipe in Inches Capacity Model O. D. Model O. D. Weight (lbs) Number Inches Number Inches A B C D E F (lbs) 450 1 2 3 Model C & S - Pipe Grabs SPECIFICATIONS Operation D. 25 • 800-836-6113 FAX 937-836-9395
Transcript
Pipe & M a n h ole H a n d lin g
PRODUCT FEATURES:
• When these high-strength, clamps are dropped over a pipe, they automatically clamp it.
¥ Outriggers stabilize the pipe during lift.¥ No blocking is required.¥ The operator only has to guide the clamp into place. ¥ Pipes can be handled quickly and efficiently when properly balanced. ¥ Excellent for cast iron, or steel pipe, as well as tubing and other
cylindrical objects.¥ Pipe grab sizes listed will handle: all classes in a category of ASA
standard cast iron pipe; standard, extra strong, and double extra strong steel pipe (all have same O.D.).
¥ Designed and manufactured to ASME B30.20.
1. Lower the grab and place on pipe. As rope is loosened grab will open and seat on pipe.2. Lift slowly with grab engaged to check for balance.3. Ideally, lift should be level, but never exceed an angle of 15¡ .
Decreasing the load by bumping or substantial imbalance can, under certain circumstances loosen the grip.Do not use in diameters other than those specified on nameplate.
Cast Iron Steel DimensionsRated Pipe Pipe in Inches
Capacity Model O.D. Model O.D. Weight(lbs) Number Inches Number Inches A B C D E F (lbs)
450
1 2 3
M od el C & S - P ipe G ra bs
SPECIFICATIONS
O pera t ion
D.25
• 800-836-6113 FAX
937-836-9395
Pipe & M a n h ole H a n d lin g
Model Standard Rated
Number Nominal Pipe Size - Description Liner size Cap Weight
HF-3/8 12" Standard Reinforced Concrete 3/8" 3000 68
HF-9/16 12" Concrete Cylinder 9/16" 3000 68
HG-11/16 16" Ductile Iron / C900 PVC 11/16" 3500 98
HG-13/16 14" Concrete Cylinder 13/16" 3500 98
HG-3/8 15" Clay Pipe 3/8" 3500 98
HG-1/4 18" PVC SDR 35 Sewer Pipe 1/4" 3500 98
HG 15" Standard Reinforced Concrete none 3500 98
SPECIFICATIONS
O pera t ion
PRODUCT FEATURES:
¥ Constructed of light weight cast aluminum ¥ Easy handling of a variety of types and sizes
of pipe ¥ Increased efficiency saves both time and
money ¥ Quickly attaches and releases from the load ¥ Product includes one set of liners to fit a
specific size. ¥ Additional liners can be purchased for added
versatility.
Lifting Eye
Models HA-LD
1-3/13Ó
3Ó
1Ó
Models HE-HG
1-5/8Ó
3-3/4Ó
15/16Ó
M od el A PG - P ipe G ra bs
D.26
• 800-836-6113 FAX
937-836-9395
Pipe & M a n h ole H a n d lin g
PRODUCT FEATURES:
¥ Pipe Tongs are of sturdy construction tohandle pipe, round bars, castings, etc.
¥ Tongs are provided with curved grippingarms for a positive grip on all types ofmaterial.
¥ Padded tongs can be furnished on requestto protect smooth or polished surfaces.
¥ Load must be balanced and controlledwhen lifting.
¥ May be used in pairs with a lifting beamfor added stability.
¥ Designed and manufactured to ASMEB30.20.
Model Rated Dia. A Wt.Number Capacity (lbs) (in) (in) (lbs)
Fixed Diameter
Model Rated Dia. A Pad Wt.Number Capacity (lbs) Min/Max Min/Max Width (lbs)
Adjustable Diameter
O pera t ion
A
B
HR
DIA.PAD
WIDTH
Decreasing the load by bumping or substantial imbalance can, under certain circumstances loosen the grip.Do not use in diameters other than those specified on nameplate.
M od el PLT - P ipe Ton g s
D.27
• 800-836-6113 FAX
937-836-9395
Pipe & M a n h ole H a n d lin g
Note: Rated capacity is per pair.
PRODUCT FEATURES:
¥ Designed for lifting and carrying steel pipes and other types of pipe.¥ This pipe hook will stay in position in a no load condition.¥ High visibility red enamel finish.¥ Designed and manufactured to ASME B30.20.
O pera t ion
WARNING! Use as pair only
FINISH: Red Enamel
SPECIFICATIONS
RATED SHACKLEMODEL CAPACITY PIN WGT.
NO. TONS DIA. LBS.PER PAIR PER PAIR (In. ) A B C D E F PER PAIR
M od el PH - P ipe H ook s
DIMENSIONS (in. )
D.28
• 800-836-6113 FAX
937-836-9395
Pipe & M a n h ole H a n d lin g
O pera t ion
Use to easily join lengths of pipe.
8Õ Carry Position4Õ Carry Positionor Empty Position
M od el CPL - C-H ook P ipe L if terPRODUCT FEATURES:
¥ Quick and efficient way to pick and place pipe.¥ Handles a wide range of precast concrete pipe.¥ Multiple lifting points allow pick point to be positioned
directly over the load center of gravity.¥ Bail is designed to remain upright for easy attachment.¥ Replaceable, non-skid urethane saddle prevents pipe
from slipping off lifter.¥ Six different models are available up to 30,000 lbs. capacity.
SPECIFICATIONS
Dimensions in inches
D.31
Note: For bell & spigot pipe only, other pipe designs, please consult factory.
Max. A rmBail Dimensions
Capacity WeightModel Pipe Size Throat Arm (D) Length Headroom A B C T (lbs. ) (lbs. ) • 800-836-6113 FA
X 937-836-9395
Rated Dimensions in InchesModel Capacity WT.
Number Tons A C E G (lbs)
Rated Dimensions in InchesModel Capacity WT.
Number Tons A B C D E F G (lbs)
P ipe & M a n h ole H a n d lin g
PRODUCT FEATURES:
¥ An efficient way to handle concrete water and sewer pipes.¥ The Caldwell ÒTea CupÓ Carrier will save you time and money.¥ Three sizes available, to handle from 3/4Ó to 1-1/2Ó cable, and lift up to
18 tons.¥ Optional ÒSpoonÓ handle allows the PC-3/4 ÒTea CupÓ to be guided into
small diameter pipes.¥ Designed and manufactured to ASME B30.20 and B30.9.
Same as standard model plus:
¥ Only wire rope needs to be inserted through pipe.
SPECIFICATIONS - Model PC
*Can use ÔSpoonÕ handle with this model.
SPECIFICATIONS - Low Profile
*Can use ÔSpoonÕ handle with this model.
M od el PC - ÒTea Cu pÓ P ipe Ca rr ier
NEW MODELLow Profile ÒTea CupÓ Pipe Carrier
D.32
• 800-836-6113 FAX
937-836-9395
Pipe & M a n h ole H a n d lin g
Rated Sling Standard After SwageUse Model Capacity Dia. Length Dim. (in) WT.With Number Tons (in) (ft) A B (lbs)
O pera t ion
ÒSpoonÓ handle for PC-3/4 onlyplease order SH-3/4(Includes bolt on lip)
ÒTea Cu pÓ P ipe Ca rr ier O ption s
SPECIFICATIONS - Model LS
Tea Cup Lifting Sling Option - LSÒSpoonÓ Handle Option - SH
PC-3/4
PC-1
Drop pipe carrier lifting sling through hole in pipe. Align and insert Òtea cupÓ pipe carrier into lifting sling.
