Piping & Instrumentation Diagrams Fundamentals Catia_001

CATIA Training

Piping & InstrumentationPiping & Instrumentation Diagrams FundamentalsDiagrams Fundamentals

Detailed StepsDetailed Steps

COPYRIGHT DASSAULT SYSTEMES 2002 Version 5 Release 8March 2002EDU-CAT-E-PID-FS-V5R8

Piping & Instrumentation Diagrams Fundamentals Detailed Steps

Table of ContentsMaster Exercise........................................................................................................................................... 3

Step (1): Starting a P&ID.......................................................................................................................... 3

Step (2): Diagram Creation...................................................................................................................... 4

Step (3): Zone Creation Management....................................................................................................16

Step (4): Diagram Modification/Annotation/Reports...............................................................................19

Step (5): Design Checks........................................................................................................................ 25

Step (6): Network Analysis..................................................................................................................... 29

Step (7): Object Navigator...................................................................................................................... 30

COPYRIGHT DASSAULT SYSTEMES 2002 2


Master Exercise

Step (1): Starting a P&IDIn this step you will learn how to start a new Piping and Instrumentation Diagram and how to set the proper options.

1. Once you have selected the P&ID workbench, a new drawing dialog box appears and you are prompted to select the following sheet options:

Standard

Format Type

Orientation

2. Change default options to desired specifications shown in the picture and click OK to activate Sheet 1.

Setting your grid

3. NOTE: Use primary spacing and Graduations.

4. Select Tools + Options - Mechanical Design - Drafting, then click the General tab and key in the primary spacing values and the graduations as shown in the picture below.





Step (2): Diagram CreationIn this step you will learn how to create Logical Lines, place Equipment and how to route Lines between Equipment.

Creating Logical Lines

1. Select the Create Line ID icon to create new logical lines .

2. Using the properties option in the Create Line ID panel, you can assign the appropriate attributes (nominal size, piping specification, etc.) Select the Properties button, select the Piping tab and assign the discrete and non-discrete attributes. For the piping lines, you can valuate the Outside Diameter and the Specifications.

3. Using the Line ID create option, create the local lines listed below.

Note: The Specification and the Nominal Diameter for each line are depicted in the linenames.

Piping Lines

45-P029-4”-CS300R-IN

45-P001-6”-CS300R-IN

45-P002-4”-CS300R-IN

45-P004-8”-CS300R-IN

45-P005-10”-CS300R-IN

45-P008-4”-CS150R-IN

45-P009-4”-CS150R-IN

45-P006-6”-CS300R-IN

45-P010-2”-CS300R-IN

I&C Lines

010

121

100A

100B

015



Placing Major Equipment4. We will place the major equipment from the catalog. This is similar to the equipment that was built

during the setup training (Advanced Exercises).

Stabilizer

Stabilizer Reboiler

Overhead Product Pumps



Placing major equipment from user defined catalog (refer to the setup training guide for the location of the catalog that was created).

5. Click the Place Component icon .

6. Select the Equipment from the catalog and place each part of the equipment as shown below -> Stabilizer, Stabilizer Reboiler, Overhead Pumps.

7. Note: The color coded connectors that allows you to distinguish between the piping connectors and

Instrumentation connectors.

8. To place multiple symbols, double-click the Place Component button. Select the button again when you are finished.

Placing Nozzles on the major equipment9. Select the catalog browser by clicking the Place Component button. Switch to the default P&ID

Catalog located in : …/intel_a/startup/EquipmentAndSystems/Piping/PipingDiagrams/ ComponentCatalogs/PID_ANSI.catalog

10. Select the Nozzle component and place the nozzles on the connectors.

11. Note: You only have to select the equipment and the compatible connectors on the equipment are automatically detected for nozzle placement.

12. Place all the nozzles on the four pieces of equipment.



13. Your document containing the Equipment+Nozzles should appear as shown in the picture.

Routing Lines between Major Equipment

14. Using the Route Piping Line option , we will route the appropriate piping line (45-P029-4”- CS300R-IN) by selecting the nozzle on the right overhead pump as the start point to the nozzle on the stabilizer as the endpoint.

15. Next, route from the left overhead pump and branch into the above line that was routed.





16. Route the Lines as shown in the picture below.

Placing Inline Parts from Catalog17. After you have selected a Part from the Browser, move the cursor over the appropriate(see next page).

5. Select the Define Zone Boundaries icon , the Define Zone Boundaries Panel is displayed.

6. Select the Zone ID.

7. Select the Boundary that you created in the previous step.8. Select OK.

Selecting and Querying Zones

9. Select the Select/Query Zone icon , the panel is isplayed. 10. Select the Local option to display the local zones.

11. For the Selection Type option, select Zone ID Members.

12. Select the Zone ID and the members that belong to the highlighted zone.

13. Also, if you select a component that belongs to a zone, the Zone ID, to which this component belongs to, is highlighted.



Updating Zones

14. Drag the lower boundary so that the reducer and the nozzle are now part of the zone.

15. Select the Update Zone Icon , you will be prompted with the message “1 zones out of 1 possible zone(s) were updated”.

16. Select OK.

17. revious steps to complete the routing of the I&C Loops 010 and 015.

Using the create text icon, you can annotate your instrumentation bubbles

25. Select the Create text command .

26. Select the anchor point as bottom center .

27. Select the point on the bubble.

28. The Annotation Editor panel is displayed. Key in the appropriate text (e.g. FC for Flow Controller).

29. Click OK.



30. Select your anchor point as top center , you can annotate the I&C Loop Number 121.



Associative Annotations31. Start a new P&ID Document.

32. Route a P&ID Line.

33. Place an In-Line Blocking Valve.

34. Using the Edit Properties option, switch the current valve position to Open.

35. Select the Create Text icon, key in Valve Position: as shown.

36. Right click on the Text and select the Attribute Link option.

37. You are prompted to select the link. From the tree select the Block Valve Function as shown highlighted.

38. The Attribute Link Panel is displayed.

39. Select the Name: CurrentValvePosition.

40. Click OK in the AttributeLink Panel.

41. The Valve Position is annotated on the schematic.

42. Using the edit properties option, change the Valve Position to Closed.

43. In the command line, key c:force update. The annotation is updated.



On-Off sheet Connectors

44. Click on the Place On-Off Sheet Connectors icon to place sheet connectors. The Catalog Browser is invoked.

45. Select the On-Off Sheets catalog and then select the component: On-Off Sheet that is simply a detail that has been cataloged.

46. Place the sheet connector by selecting the connector/segment.

47. Note: The sheet connectors automatically place based on the flow.

48. Apply the Connectors to the entire Diagram.

49. The final thing to do in this step is to annotate the diagram using the text function till it matches the picture on the next pages.





Step (3): Zone Creation ManagementIn this step you will learn how to create Zones and how to manage them.

Zone Creation

1. Select the Create Zone icon .

2. Key in a Zone ID e.g. HEAT TRACING ZONE

3. Select the OK button.

Creating the boundaries for Zones 4. Create the Zone boundary geometry using V5R8 drafting tools (see next page).

5. Select the Define Zone Boundaries icon , the Define Zone Boundaries Panel is displayed.

6. Select the Zone ID.

7. Select the Boundary that you created in the previous step.

8. Select OK.



Selecting and Querying Zones

9. Select the Select/Query Zone icon , the panel is displayed.

10. Select the Local option to display the local zones.

11. For the Selection Type option, select Zone ID Members.

12. Select the Zone ID and the members that belong to the highlighted zone.

13. Also, if you select a component that belongs to a zone, the Zone ID, to which this component belongs to, is highlighted.



Updating Zones 14. Drag the lower boundary so that the reducer and the nozzle are now part of the zone.

15. Select the Update Zone Icon , you will be prompted with the message “1 zones out of 1 possible zone(s) were updated”.

16. Select OK.

17. Select the Select/Query Zone Icon, select the Zone ID, select the option Zone ID members.

18. The new components (the Reducer and the Nozzle) now belong to the Zone.



Step (4): Diagram Modification/Annotation/ReportsIn this step you will learn how to modify the positions of Lines and Equipment, how to modify Annotations, how to manage Flows and how to generate Reports.

Gapping Operations1. Gapping operations are performed using the View option in the frame. Select Gaps – Show All Gaps.

2. Gapping management is performed using the Tools - Options command. This option allows you to set parameters such as:

Gap Type

Gap Size

Gap Priority

Flow Management3. Using the View - Flow option , you can Show or Noshow the flow for all lines.

4. You can use the Flow icons to show the flow and to change your flow direction for selected lines.

5. An alternate method would be to use the contextual menu on the line segment.



6. Using the Tools - Options – Equipment&Systems - Diagrams tab, you can set your Flow arrow information:

Flow Frequency

Flow Positioning

Flow Arrow Type



Stretch Operations7. Stretch operations allow you to move components by trapping them.

8. E.g. selecting equipment with attached components will allow you to move it as an entity.

9. Trap a portion of your diagram and experiment with the stretch operations.

Flip Inline Parts.10. Flip Connections: Flips the Connectors of a Parts and reassembles it.

11. Flip In Line: Mirrors the Parts along the Line.



Manage your Annotations12. You can edit the properties on the annotation using the Properties option by right clicking on the annotation.

13. To modify the annotation, use the Annotation Editor by right clicking on the annotation.



Generating Reports.14. At first you need to select the Lines that shall be included in the report. You can use the

Select/Query Line ID to select the desired Line Ids or just select them in the tree.

15. Then run the Report-Macro as shown below.

16. Confirm the appearing dialog by clicking OK.





Step (5): Design ChecksIn this step you will learn how to implement and apply design checks to your piping diagram.

Methodology:1. Design checks are executed via the Knowledge Expert workbench. Basically, rules are imported

into the design document and then executed against the components in the document.

2. Start a new P&ID Document.

3. Double click on the root product.

4. Using the Start menu, invoke the Knowledge Expert workbench.

5. Click on the Insert Rules Icon.

6. Select the document PipingDiagramChecks.CATProduct from the following location: …\intel_a\startup\EquipmentAndSystems\Piping\DesignRules

7. Select the Open button.

The checks are imported into your design document.

8. In this scenario we will execute some of the checks.

9. Create a control station assembly as shown below.



Performing and Exploring a Design Check10. We will explore the UnconnectedConcidentElem check by disconnecting one of the components.

11. Disconnect one of the block valves so that the component is disconnected but it is still

coincident. Use the Disconnect function .

12. Right click on the RuleBase and run the Manual Complete Solve from the contextual menu.



Highlight the failed components 13. By right clicking on the rule and using the Highlight Failed Components option from the contextual menu, the failures can be displayed interactively in the Tree Structure.



Generate a failure Report14. To generate a failure Report perform a right click on Rule Base and select RuleBase object – Report.

15. Select the Directory where the Report shall be stored.

16. The Report will be generated in HTML format. To see the report, go to the desired directory and open the file main.html with a browser.

17. Every Item that is marked green is OK. Every red X marks a problem in your diagram.



Step (6): Network AnalysisIn this step you will learn how to use the network analysis function under Analyze – Networks.

To perform a network analysis click on Analysis – Network in the Menubar.

1. Activate the Network tab and select a part from your diagram. Everything that is connected to the selected part will be highlighted. In the Dialog the number of objects in network will be displayed. When you click on Close the highlighted parts will be selected.

2. Under the Path tab you can select two objects (from – to) in your diagram. If there are more than one possibilities to connect the part, you might choose the desired path in the Current Path selection box. In the Dialog the number of objects in network will also be shown.



Step (7): Object NavigatorIn this step you will learn how to use the object navigator.

The Object Navigator allows designers to browse their documents and view the objects for connectivity and also view the object properties.

1. Click on Analyze – Related Object to start the Object Navigator.

2. Select a part from your diagram (e.g. a pump).

3. The Part and its related objects (e.g. a pump and its nozzles) will be shown in the Current Selection Window.

Using the object navigator

4. With a right click you can enter the properties menu of every part that is displayed in the Current Selection Window.


Date post:	13-Apr-2015
Category:	Documents
Upload:	rvsingh70
View:	121 times
Download:	4 times

Piping & Instrumentation Diagrams Fundamentals Catia_001

Documents