+ All Categories
Home > Documents > PIR OCCUPANCY SWITCHES - Danlers Limited · 0 5m 10m Scale 12 The diagram illustrates PIR occupancy...

PIR OCCUPANCY SWITCHES - Danlers Limited · 0 5m 10m Scale 12 The diagram illustrates PIR occupancy...

Date post: 04-Sep-2018
Category:
Upload: vantu
View: 216 times
Download: 0 times
Share this document with a friend
24
8 The DANLERS range of passive infra-red occupancy switches is designed for the automatic control of lighting, heating, ventilation or air conditioning loads. The PIR switch will switch on the connected load automatically when an area is occupied, and then switch it off automatically when the area has been vacant for a chosen duration. This has the benefits of reduced energy bills and automatic control. When being used to control lighting, the built-in photocell can be used to keep the lights off on bright days. DANLERS also offer a Ceiling surface mounted passive infra-red absence switch which requires a wall switch to turn on the load - see page 38 for details. Offices Staff rooms Factories Corridors and stairwells Warehouses Residential homes Schools Military accommodation Leisure centres Student accommodation Hospitals Toilet blocks Canteens Changing rooms Car Parks Plus many other uses PIR occupancy switches are ideal for: Additional range products Special variants of products are available on request with additional range lenses for installations requiring a greater detection area or longer thinner detection areas. In some cases this may require a greater range of movement to register detection. PIR occupancy switches PIR OCCUPANCY SWITCHES PIR occupancy switch variants Special variants of products are available on request such as 24V (a.c. or d.c.) versions of our PIR occupancy switches and photocell switches, ideal for low voltage control systems. 12V variants can also be supplied. Some variants are available from stock for next day delivery. To special order we can also supply volt free outputs for mains, 24V or 12V supplies (including versions with gold relays). M A D E I N T H E U K 5 Y E A R W A R R A N T Y
Transcript

8

The DANLERS range of passive infra-red occupancy switches is designed for the automatic control of lighting, heating, ventilation or air conditioning loads.

The PIR switch will switch on the connected load automatically when an area is occupied, and then switch it off automatically when the area has been vacant for a chosen duration. This has the benefits of reduced energy bills and automatic control. When being used to control lighting, the built-in photocell can be used to keep the lights off on bright days.

DANLERS also offer a Ceiling surface mounted passive infra-red absence switch which requires a wall switch to turn on the load - see page 38 for details.

• Offices • Staff rooms

• Factories • Corridors and stairwells

• Warehouses • Residential homes

• Schools • Military accommodation

• Leisure centres • Student accommodation

• Hospitals • Toilet blocks

• Canteens • Changing rooms

• Car Parks • Plus many other uses

PIR occupancy switches are ideal for:

Additional range products

Special variants of products are available on request with additional range lenses for installations requiring a greater detection area or longer thinner detection areas. In some cases this may require a greater range of movement to register detection.

PIR occupancy switches

PIR OCCUPANCY SWITCHES

PIR occupancy switch variants

Special variants of products are available on request such as 24V (a.c. or d.c.) versions of our PIR occupancy switches and photocell switches, ideal for low voltage control systems. 12V variants can also be supplied. Some variants are available from stock for next day delivery. To special order we can also supply volt free outputs for mains, 24V or 12V supplies (including versions with gold relays).

MADE IN

T H E U K

5 Y E A R

WA R R A NTY

9

PIR occupancy switch functions

Each PIR occupancy switch in the DANLERS range has a passive infra-red quad person detector (except COPD which has a passive infra-red dual person detector). This detects the movement of a warm body moving within its detection zone. When such a movement is detected the load is switched on. There is a time lag function which is adjusted using a spindle on the side of the product. The time lag is the time that must elapse with no movement detected before the PIR occupancy switch will switch off.

There is a built-in, adjustable, photocell override which can be used to keep lights off when there is sufficient daylight available (except “Intelligent” range of controls - see page 24). The photocell can only be used in this way if the amount of natural daylight exceeds the level of the artificial ligh§ts. The photocell can be set to inactive when controlling heating, ventilation or air conditioning. The photocell is also adjusted by a spindle on the side of the product.

Each PIR occupancy switch contains a relay suitable for switching most types of load, including fluorescent lights, LEDs and fans.

A few PIR occupancy switches may be wired in parallel to control the same load. However, there are minimum load restrictions with the WAPIR model only (see page 29). The PIR occupancy switches require a mains supply.

Simple adjustment spindles

Night, Unoccupied – Lighting OFF

Night, Occupied – Lighting ON

Enough daylight, Unoccupied – Lighting OFF

Enough daylight, Occupied – Lighting OFF

PIR occupancy switch brings lights on – only when needed

Function demonstrated with the lighting in an office

PIR OCCUPANCY SWITCHES

ControlZAPP

DANLERS ControlZAPP enabled PIR Occupancy Switches have functions similar to those of the traditional DANLERS range of PIR Occupancy Switches with many new features added to the easy to set up, programmable, bluetooth low energy interface.

For the more details on ControlZAPP see pages 6-7 or for the latest ControlZAPP product information telephone: +44 (0)1249 443377 or email: [email protected]

10

PIR detector

Passive infra-red quad person detector.

Adjustable time lag

Time lag adjustable in 9 steps (approximate values): 10 seconds, 20 seconds, 40 seconds, 1.25 minutes, 2.5 minutes, 5 minutes, 10 minutes, 20 minutes, 40 minutes.

Adjustable photocell

The "Inhibit on" photocell on most models will inhibit the lights from switching on when somebody enters an area with plenty of ambient light. However, if somebody is already occupying an area with the lights switched on, the lights will remain on while the area is occupied, regardless of any increase in the ambient light level. This is to avoid any nuisance switching off when somebody is in the middle of a task or meeting. Range 100-1000 lux (and photocell inactive), falling on the working plane.

The “Intelligent” photocell on some batten mount controls (see page 24) enables even greater energy savings because in its calibration process it learns to ignore the artificial lighting load (Patent pending, GB Patent application 1219746.3). It is recommended the “Intelligent” batten mount controls are only used in areas with some natural daylight. Range 100-3000 lux falling on the working plane.

Loading

All models can switch up to 6 amps (1500W at 230VAC) of resistive, transformer or fluorescent lighting loads, 2 amps (500W) of low energy lighting loads (LED lamps and compact fluorescent) or up to 1 amp (250W) of fans or most metal halide lamps. For the WAPIR model there are some minimum load requirements (details on page 29).

Wiring in parallel

A few PIR switches can be wired in parallel to control the same load.

Start-up Mode

When the mains supply is initially connected to the PIR occupancy switch it goes through its Start-up Mode. This means it switches on for about 1 minute, then switches off and enters its Operating Mode. If a manual wall switch is feeding the PIR occupancy switch (see wiring diagrams on appropriate product pages) then it will go through the Start-up Mode each time the wall switch is switched on (not applicable to WAPIR, see page 29).

By wiring the manual wall switch in the alternative position, the supply to the PIR occupancy switch is uninterrupted and it remains in Operating Mode. It does not go through its Start-up Mode each time the wall switch is switched on.

PIR OCCUPANCY SWITCHES

PIR occupancy switch specifications

11

PIR OCCUPANCY SWITCHES

Selecting the appropriate PIR occupancy switch

CEILING MOUNTED WALL MOUNTED

360˚ detection zone

120˚ directional

detection angle

Long range directional

narrow beam

120˚ detection

angle

Flush-mounted (false or plasterboard

ceilings)

Surface mounted Batten mounted

Surface mounted Surface mounted Plaster depth (16mm) wall box

Hard wired

Plug and socket

Hard wired

Plug and socket

Hard wired to lamp ballast

Plug and socket

Plug and socket

Needs neutral

wire

No neutral wire

needed

CEFL PIR Page 14

CEFL PIR SEALED Page 15

CEFL PIR 10A

Page 15

CEFLP PIR + CESO

Page 14

CESF PIR Page 16

CESF PIR IP66

Page 17

CESFA PIR

(Absence switch)

Page 38

CELO + CESO SQ Page 20

BMINTPIR SP, 5M or 10M

Page 24

BMPIR SP, 5M or 10M

Page 25

BMEXPIR Page 26

CEDR 6P + CESO

Page 22

CEDR 6PLR + CESO Page 23

WACE PIR Page 28

WAPIR Page 29

5m 10m0

Scale

12

The diagram illustrates PIR occupancy switch siting within a typical office/factory facility. The coloured zones emanating from the controls show strong detection zones (darker tints with solid coloured line) and secondary detection zones (lighter tint with broken coloured line).

Ceiling flush-mounted CEFL PIR spaced every 5 metres to cover the open plan office and control the lights. The CEFL PIR can be wired in groups in parallel, to control the lighting in zones.

Long range directional CEDR 6PLR to detect people in the 25 metre corridor.

Two ceiling flush-mounted CEFL PIR controlling the lights in a meeting room. In this, and other offices, a manual wall switch is retained to override the lights to off, e.g. for a video presentation.

Small offices are covered by a single ceiling flush-mounted CEFL PIR or alternatively with an absence switch CESFA PIR.

The wall switch has been replaced by a wall mounted WAPIR.

MEETING ROOM OFFICE

OFFICE

OFFICE

CORRIDOR

OPEN PLAN OFFICES

RECEPTION

STAIRWELL

TOILETS

FACTORY AREA

HIGH BAY RACKING

RESTROOM

OP

EN

S

TAIR

CA

SE

HIGH BAY RACKING

SHOWER ROOM

TOILET LOBBY

PIR OCCUPANCY SWITCHES

Application diagram

13

Long range directional CEDR 6PLR detects people in a racking storage aisle.

Batten mounted BMINTPIR5M fitted to every other batten lamp fitting to give total coverage of the open plan factory area.

Ceiling flush-mounted CEFL PIR spaced every 5 metres to cover the open plan reception area and control the lights.

Ceiling plug-in CELO mounted on BESA box on ceiling conduit. Spaced at 5 metre intervals to control the lights in the restroom.

In the shower room a CEFL PIR SEALED is used, as it has protection against light splashes and condensation.

In the toilets a ceiling flush- mounted CEFL PIR has been wired in parallel with a wall mounted WACE PIR in the lobby, to control the lighting in both rooms together.

Two ceiling surface- mounted CESF PIR (one on each landing) wired in parallel to control the lighting in the stairwell.

Ceiling directional CEDR 6P covers the open staircase.

MEETING ROOM OFFICE

OFFICE

OFFICE

CORRIDOR

OPEN PLAN OFFICES

RECEPTION

STAIRWELL

TOILETS

FACTORY AREA

HIGH BAY RACKING

RESTROOM

OP

EN

S

TAIR

CA

SE

HIGH BAY RACKING

SHOWER ROOM

TOILET LOBBY

PIR OCCUPANCY SWITCHES

14

Special versions

Plug and socket version: CEFLP PIR

Model CEFLP PIR is provided with a plug suitable for the CESO Ceiling socket shown on page 21. CEFLP PIR is also suitable for use with HAGER marshalling boxes.

Loading: Up to 6 amps (1500W) of resistive, transformer or fluorescent lighting loads, up to 2 amps (500W) of low energy lighting loads (LED lamps and compact fluorescent) or up to 1 amp (250W) of fans or most metal halide lamps

Ceiling flush-mounted PIR occupancy switch

Control plugged into a CESO on

a BESA box

These neat and unobtrusive models are ideal for flush mounting through suspended or plasterboard ceilings. They have a 2m cable, for quick and easy installation.

Order code: CEFLP PIR

Order code: CEFL PIR

Specification

Detection zone: 360°

Time lag range: 10 seconds to 40 minutes in 9 steps

Photocell range: 100 to 1000 lux, and inactive

Loading: Up to 6 amps (1500W) of resistive, transformer or fluorescent lighting loads, up to 2 amps (500W) of low energy lighting loads (LED lamps and compact fluorescent) or up to 1 amp (250W) of fans or most metal halide lamps

Wiring diagram: See diagrams 14a and 14b below

Dimensions: 72mm diameter x 68mm

NN

Fig. 201 Ceiling mounted PIR occupancy switch

Up to 5m

Up to 7m

Up to 5m

Up to 7m

Up to 5m

Up to5m

In open plan areas For best coverage the CEFL PIR should be spaced every 5m in either direction

CEFL PIR Strong detection zone

Secondary detection zone

Strong detection zone i.e. person moving arm

Secondary detection zone i.e. person walking (less sensitive when walking straight towards PIR switch)

For optimum coverage recommended mounting height between 2.4 and 5m.

PIR Quad detector gives 124 detection areas within the zone.

Plan view of detection zone Several PIR occupancy switchesPerspective view of detection zone

L

load

optional manual wall switch for overriding off

A few CEFL PIR230 VAC

L

load

CEFL PIR

optional manual wall switch for overriding off

14a. Single CEFL PIR

230 VAC

alternative position for optional wall switch (see p.10 “Start-up Mode”)

14b. A few CEFL PIR wired in parallel

alternative position for optional wall switch (see p.10 “Start-up Mode”)

Ideal for false or plasterboard

ceilings

55

3

2m cable

60

72

72

side plan

66

Requires 63 or 64mm (2.5") diameter hole in a false or plasterboard ceiling

38

PIR occupancy switch variants

Variants are available on request such as 24V or 12V (a.c. or d.c.), ideal for low voltage control systems. To special order we can also supply volt free outputs for mains, 24V or 12V supplies (including versions with gold contact relays). Please see page 19 for more information.

SL

SL SL SL

PIR OCCUPANCY SWITCHES

Detection diagrams

Dimensions in mm Wiring diagrams

15

Order code: CEFL PIR 10A

Splashproof ceiling flush-mounted PIR occupancy switch

Order code: CEFL PIR SEALED CEFL PIR XS

Model CEFL PIR SEALED is protected against light splashes and condensation when installed in the ceiling. Ideal for bathrooms, shower rooms, etc.

Specification

Detection zone: 360°

Time lag range: 10 seconds to 40 minutes in 9 steps

Photocell range: 100 to 1000 lux, and inactive

Loading: Up to 6 amps (1500W) of resistive, transformer or fluorescent lighting loads, up to 2 amps (500W) of low energy lighting loads (LED lamps and compact fluorescent) or up to 1 amp (250W) of fans or most metal halide lamps

Wiring diagram: See diagrams 15a and 15b below

Dimensions: 72mm diameter x 68mm

An extra sealed version (order code: CEFL PIRXS) is also available on request. Ideal for domestic bathrooms and toilets (zone 2).

Specification

Detection zone: 360°

Time lag range: 10 seconds to 40 minutes in 9 steps

Photocell range: 100 to 1000 lux, and inactive

Loading: Up to 10 amps (2500W) of resistive, transformer or fluorescent lighting loads, up to 2 amps (500W) of low energy lighting loads (LED lamps and compact fluorescent) or up to 1 amp (250W) of fans or most metal halide lamps

Wiring diagram: See diagrams 15a and 15b below

Dimensions: 72mm diameter x 68mm

10 amp rated ceiling flush-mounted PIR occupancy switch

Fig. 201 Ceiling mounted PIR occupancy switch

Up to 5m

Up to 7m

Up to 5m

Up to 7m

Up to 5m

Up to5m

In open plan areas For best coverage the CEFL PIR should be spaced every 5m in either direction

CEFL PIR Strong detection zone

Secondary detection zone

Strong detection zone i.e. person moving arm

Secondary detection zone i.e. person walking (less sensitive when walking straight towards PIR switch)

For optimum coverage recommended mounting height between 2.4 and 5m.

PIR Quad detector gives 124 detection areas within the zone.

Plan view of detection zone Several PIR occupancy switchesPerspective view of detection zone

L

optional manual wall switch for overriding off

A few PIR occupancy switches

230 VAC

L

load

PIR occupancy

switch

optional manual wall switch for overriding off

15a. Single PIR occupancy switch

230 VAC

alternative position for optional wall switch (see p.10 “Start-up Mode”)

15b. A few PIR occupancy switches wired in parallel

alternative position for optional wall switch (see p.10 “Start-up Mode”)

55

3

2m cable

60

72

72

side plan

66

Requires 63 or 64mm (2.5") diameter hole in a false or plasterboard ceiling

38

These neat and unobtrusive models are ideal for flush mounting through suspended or plasterboard ceilings. They have a 2m cable, for quick and easy installation.

N

SL SL SL

SL

N

PIR OCCUPANCY SWITCHES

Detection diagrams

Dimensions in mm Wiring diagrams

16

PIR OCCUPANCY SWITCHES

These surface-mounted models are ideal for solid ceilings.

Ceiling surface-mounted PIR occupancy switch

Can be mounted on a square pattress box, order code: PABO.

Order code: CESF PIR

The CESF PIR is a hard wired version and can be mounted on a square pattress box.

Specification

Detection zone: 360°

Time lag range: 10 seconds to 40 minutes in 9 steps

Photocell range: 100 to 1000 lux, and inactive

Loading: Up to 6 amps (1500W) of resistive, transformer or fluorescent lighting loads, up to 2 amps (500W) of low energy lighting loads (LED lamps and compact fluorescent) or up to 1 amp (250W) of fans or most metal halide lamps

Wiring diagram: See diagrams 16a and 16b below

Dimensions: 86 x 86 x 22mm. Requires back box depth 16mm

L

Nload

A few CESF PIR230 VAC

L

N

load

CESF PIR

optional manual wall switch for overriding off

16a. Single CESF PIR

230 VAC

16b. A few CESF PIR wired in parallel

Fig. 201 Ceiling mounted PIR occupancy switch

Up to 5m

Up to 7m

Up to 5m

Up to 7m

Up to 5m

Up to5m

In open plan areasFor best coverage the CESF PIR should be spaced every 5m in either direction

CESF PIRStrong detection zone

Secondary detection zone

Strong detection zone i.e. person moving arm

Secondary detection zone i.e. person walking (less sensitive when walking straight towards PIR switch)

For optimum coverage recommended mounting height between 2.4 and 5m.

PIR Quad detector gives 124 detection areas within the zone.

Plan view of detection zone Several PIR occupancy switchesPerspective view of detection zone

plan side

22

86

86

alternative position for optional wall switch (see p.10 “Start-up Mode”)

alternative position for optional wall switch (see p.10 “Start-up Mode”)

optional manual wall switch for overriding off

Requires 16mm deep box

Ceiling surface-mounted PIR occupancy switch variants

Variants are available on request such as 24V or 12V (a.c. or d.c.), ideal for low voltage control systems. To special order we can also supply volt free outputs for mains, 24V or 12V supplies (including versions with gold contact relays).

Please see page 19 for more information.

SL SL SL

SL

Dimensions in mm Wiring diagrams

Detection diagrams

17

This IP66 rated surface-mounted model is ideal for solid ceilings.

IP66 rated ceiling surface-mounted PIR occupancy switch

Order code: CESF PIR IP66

The CESF PIR IP66 has an IP66 rated enclosure and is ideal for use in zone 2 in bathrooms, shower rooms, washdown areas etc.

CESF PIR IP66 is hard wired.

Unlike CESF PIR (see page 16) the 3 adjustment spindles for Time lag, Sensitivity and Lux settings are located on the back of the product.

Specification

Detection zone: 360°

Time lag range: 10 seconds to 40 minutes in 9 steps

Photocell range: 100 to 1000 lux, and inactive

Loading: Up to 6 amps (1500W) of resistive, transformer or fluorescent lighting loads, up to 2 amps (500W) of low energy lighting loads (LED lamps and compact fluorescent) or up to 1 amp (250W) of fans or most metal halide lamps

Wiring diagram: See diagrams 17a and 17b below

Dimensions: 87 x 87 x 53mm.

Other CESF PIR IP66 variants include:

12 volt, 24 volt, 12 volt with volt free contacts, 24 volt with volt free contacts plus a tamperproof version. Please contact us for more information.

L

Nload

A few CESF PIR IP66

230 VAC

L

N

load

CESF PIR IP66

optional manual wall switch for overriding off

17a. Single CESF PIR IP66

230 VAC

17b. A few CESF PIR IP66 wired in parallel

Fig. 201 Ceiling mounted PIR occupancy switch

Up to 5m

Up to 7m

Up to 5m

Up to 7m

Up to 5m

Up to5m

In open plan areasFor best coverage the CESF PIR IP66 should be spaced every 5m in either direction

CESF PIR IP66Strong detection zone

Secondary detection zone

Strong detection zone i.e. person moving arm

Secondary detection zone i.e. person walking (less sensitive when walking straight towards PIR switch)

For optimum coverage recommended mounting height between 2.4 and 5m.

PIR Quad detector gives 124 detection areas within the zone.

Plan view of detection zone Several PIR occupancy switchesPerspective view of detection zone

alternative position for optional wall switch (see p.10 “Start-up Mode”)

alternative position for optional wall switch (see p.10 “Start-up Mode”)

optional manual wall switch for overriding off

SL SL SL

SL

PIR OCCUPANCY SWITCHES

Dimensions in mm Wiring diagrams

Detection diagrams

plan side

53

87

86

87

18

Ceiling flush-mounted PIR occupancy switch variants

DANLERS manufacture a range of variants of the Ceiling flush-mounted PIR for integrating into building management systems, low voltage applications etc.

Order code: CEFL PIR 12V CEFL PIR 12VVF CEFL PIR 24V CEFL PIR 24VVF

12 volt version: CEFL PIR 12V Operating voltage of the switch is 12 volt a.c. or d.c.

12 volt version with volt free contacts: CEFL PIR 12VVF Operating voltage of the switch is 12 volt a.c. or d.c. Comes with 4-core flex.

24 volt version: CEFL PIR 24V Operating voltage of the switch is 24 volt a.c. or d.c.

24 volt version with volt free contacts: CEFL PIR 24VVF Operating voltage of the switch is 24 volt a.c. or d.c. Comes with 4-core flex.

Specification

Detection zone: 360°

Time lag range: 10 seconds to 40 minutes in 9 steps

Photocell range: 100 to 1000 lux, and inactive

Loading: 12V to 240V: 10mA to 6 amps of resistive, transformer or fluorescent lighting loads, up to 2 amps of low energy lighting loads (LED lamps and compact fluorescent) or up to 1 amp of fans or most metal halide lamps

Wiring diagram: See diagrams 18a and 18b below

Dimensions: 72mm diameter x 68mm

Other PIR occupancy switch variants

DANLERS also manufacture other variants of their PIR occupancy switches (see table opposite).

Fig. 201 Ceiling mounted PIR occupancy switch

Up to 5m

Up to 7m

Up to 5m

Up to 7m

Up to 5m

Up to5m

In open plan areasFor best coverage the PIR should be spaced every 5m in either direction

PIRStrong detection zone

Secondary detection zone

Strong detection zone i.e. person moving arm

Secondary detection zone i.e. person walking (less sensitive when walking straight towards PIR switch)

For optimum coverage recommended mounting height between 2.4 and 5m.

PIR Quad detector gives 124 detection areas within the zone.

Plan view of detection zone Several PIR occupancy switchesPerspective view of detection zone

55

3

2m cable

60

72

72

side plan

66

Requires 63 or 64mm (2.5") diameter hole in a false or plasterboard ceiling

38

18a. Volt free, normally open

18b. Volt free, normally closed

Volt Free, Normally Open

SupplyVoltage

Neutralor 0V

NO

Load

Volt Free, Normally Closed

SupplyVoltage

Neutralor 0V

NC

Load

SupplyVoltage

Neutralor 0V

Volt Free, Change Over

C

NO

NC

Load(s)

PIR OCCUPANCY SWITCHES

Detection diagrams

Dimensions in mm Wiring diagrams

19

PIR OCCUPANCY SWITCH VARIANTS

DANLERS manufacture many other variants of their PIR occupancy switches including those listed below, many of which can be combined in the same product. For example: A Ceiling Flush Mounted PIR Occupancy Switch (CEFL PIR) with a sealed enclosure (S) to be used with an operating voltage of 12 volts requiring volt free contacts for switching a secondary signal (VF) would be CEFL PIR S12VVF.

If your requirement does not feature on this list please call us to discuss your requirements as other options can be considered. Grid PIR modules and Interior batten mount controls are not available in any of the variants.

NOTE: In the table below if the product has a within its column the product can be manufactured in that variant.

Product code Suffix

Functionality

CE

FL P

IR

CE

SF P

IR

CE

SF P

IR I

P66

CE

LO

CE

DR

6P

CE

DR

6P

CE

FLP

IRLR

WA

CE

PIR

WA

PIR

CO

PD

S or SEALED

Sealed enclosure against light splashes and condensation within zone 2. (For CESF PIR see CESF PIR IP66).

XSExtra sealed enclosure against light splashes, condensation and draughty ceiling voids. Ideal for domestic bathrooms and cloakrooms.

10A Relay load rated up to 10 amp (2500W) resistive load.

12V 12 volt operating voltage a.c. or d.c.

24V 24 volt operating voltage a.c. or d.c.

VFVolt free contacts for switching a secondary signal, rather than the supply voltage. The CEFLPIRVF version is supplied with a 5-core flex.

NCNormally closed relay contacts - The relay contacts will open when the PIR detects and remain open until the time lag has expired.

2DDouble detection - Switches the load ON after it detects twice in succession, to help prevent false triggering in small application areas.

RS Reduced sensitivity - to help prevent false triggering in small application areas.

AR Additional range - Some products can be manufactured with alternative lens types enabling greater detection areas.

HL Hard lens - A hard lens can be fitted to some products to prevent false triggering in draughty environments.

OC Open collector, 30VDC max, 100mA max

G Gold contacts - High voltage, low current

LG Logic Gold contacts - Low voltage, low current

3M, 4M, 5M etc

Various cable lengths can be supplied with Ceiling flush mounted products if you do not require the standard 2 metre length.

DANLERS ControlZAPP enabled PIR Occupancy Switches have functions similar to those of the traditional DANLERS range of PIR Occupancy Switches with many new features added to the easy to set up, programmable, bluetooth low energy interface. For the more details on ControlZAPP see pages 6-7.

20

Ceiling surface-mounted plug-in PIR occupancy switch

These surface-mounted models are ideal for solid ceilings.

Order code: CELO Requires socket, order code: CESO SQ or CESO (see page 21)

The CELO has a built-in plug suitable for the CESO SQ Ceiling socket (or CESO Ceiling socket). CESO SQ can be mounted on a square pattress box (the CESO can be mounted on a BESA box).

Specification

Detection zone: 360°

Time lag range: 10 seconds to 40 minutes in 9 steps

Photocell range: 100 to 1000 lux, and inactive

Loading: (Each circuit) up to 6 amps (1500W) of resistive, transformer or fluorescent lighting loads, up to 2 amps (500W) of low energy lighting loads (LED lamps and compact fluorescent) or up to 1 amp (250W) of fans or most metal halide lamps.

Wiring diagram: See diagrams 20a, 20b, 20c below

Dimensions: 88 x 88 x 47mm

L

load

optional manual wall switch for overriding off

CELOCELOCELO230 VAC

20a. Single CELO 20b. A few CELO wired in parallel 20c. Ceiling mounted socket (CESO SQ or CESO)

L N SL CELO Not to scale

CESO SQ or CESO

Pattress box or BESA box

luminaire

L N

SL

N

L

load

CELO

optional manual wall switch for overriding off

230 VAC

N

plan side

47

88

88

(CESO SQ)

alternative position for optional wall switch (see p.10 “Start-up Mode”)

alternative position for optional wall switch (see p.10 “Start-up Mode”)

Up to 5m

Up to 7m

Up to 5m

Up to 7m Up to 5m

Up to5m

In open plan areasFor best coverage the CELO should be spaced every 5m in either direction

CELOStrong detection zone

Secondary detection zone

Strong detection zone i.e. person moving arm

Secondary detection zone i.e. person walking (less sensitive when walking straight towards PIR switch)

For optimum coverage recommended mounting height between 2.4 and 5m.

PIR Quad detector gives 124 detection areas within the zone.

Plan view of detection zone Several PIR occupancy switchesPerspective view of detection zone

L N ASL SL SL

SL

PIR OCCUPANCY SWITCHES

Detection diagrams

Dimensions in mm

Wiring diagrams

Ceiling socket (CESO SQ)

21

Ceiling socket: CESO

For use with DANLERS plug-in ceiling controls. Can be mounted on a BESA box.

Wiring diagram: See diagram 21a below

Dimensions: 74mm diameter x 13mm

Order code: CESO

Sockets for plug-in ceiling controls

21a. Ceiling mounted socket (CESO or CESO SQ) for plug-in ceiling controls

L N SLplug-in ceiling control Not to scale

CESO or CESO SQ

BESA box or pattressbox

luminaire

L N

SL

L1

N1

CE2SLplus plug-in switch

separate circuit

230 VAC

optional manual wall switch for overriding off

SL1

load

L1

SL2N/C

N1

CESLplus plug-in switch

separate circuit

optional manual wall switch for overriding off

230 VAC load

SL1

SL2N/O

C2 SL2N/O

SL2N/C

SL3N/O

SL3N/C

C3C2

separate circuit

21c. Plug-in control plus double slave relay with volt free changeover contacts (CE2SL) controlling two extra circuits

21b. Plug-in control plus slave relay with volt free changeover contacts (CESL) controlling one extra circuit

Ceiling socket (CESO)

side

plan

74

13

Ceiling slave relays (CESL / CE2SL)

plan side

41

87

87

87

Order code: CESO SQ

plan side

13

87

87

87

Slave relays for plug-in ceiling controls

Ceiling socket with slave relay: CESL

Ceiling socket with slave relay with isolated changeover contacts. Enables the switching of an additional circuit with its own supply, e.g. the corridor lights outside an office or a separate low voltage control circuit. A no socket version is available on request.

Loading: (Each circuit) up to 6 amps (1500W) incandescent or mains halogen lamps. Up to 4 amps (1000W) electronic or wire wound transformers, fluorescent lamps (high frequency or switch start). Up to 2 amps (500W) compact fluorescent or LED lamps. Up to 1 amp (250W) most fans and metal halide discharge lamps.

Wiring diagram: See diagram 21b below

Dimensions: 87 x 87 x 41mm Ceiling socket with double slave relay: CE2SL

Ceiling socket with a double slave relay with isolated changeover contacts. Enables the switching of two additional circuits, each with its own supply, e.g. the corridor lights outside an office, plus the extractor fans inside the office. Also ideal for controlling two separate low voltage control circuits. A no socket version is available on request.

Loading: As CESL above

Wiring diagram: See diagram 21c below

Dimensions: 87 x 87 x 41mm

Order code: CESL or CE2SL

Also available as a square socket.

Ceiling socket: CESO SQ

Can be mounted on a square pattress box.

Wiring diagram: See diagram 21a below

Dimensions: 87 x 87 x 13mm

L N A

ANCILLARY PRODUCTS

Dimensions in mm

Wiring diagrams

22

Ceiling directional PIR occupancy switch

Standard range Order code: CEDR 6P Requires socket, order code: CESO (see page 21)

Standard range version

Designed to give a directional view of the activity to be monitored. Detection angle 120°.

Specification

Time lag range: 10 seconds to 40 minutes in 9 steps

Photocell range: 100 to 1000 lux, and inactive

Loading: Up to 6 amps (1500W) of resistive, transformer or fluorescent lighting loads, up to 2 amps (500W) of low energy lighting loads (LED lamps and compact fluorescent) or up to 1 amp (250W) of fans or most metal halide lamps

Wiring diagram: See diagrams 22a, 22b, 22c below

Dimensions: See below

CEDR 6P can be rotated and lowered

to a 45º angle

These directional PIR switches plug into a ceiling mounted socket. The socket can be mounted on a BESA box.

L

load

optional manual wall switch for overriding off

A few CEDR 6P230 VAC

L

load

CEDR 6P

optional manual wall switch for overriding off

22a. Single CEDR 6P

230 VAC

22b. A few CEDR 6P wired in parallel 22c. Ceiling mounted socket (CESO)

Up to 5m Up to 10m

Strong Detection Zone

Secondary Detection Zone

60° 120°

CEDR 6P

Up to 5m Up to 10m

Strong Detection Zone

Secondary Detection Zone

60° 120°

CEDR 6P

Strong Detection Zonei.e. person moving arm

Secondary Detection Zonei.e. person walking across the zone

Plan view Side elevation

CEDR 6P

L N SL CEDR 6P Not to scale

CESO

BESA box

luminaire

L N

SL

NN

alternative position for optional wall switch (see p.10 “Start-up Mode”)

alternative position for optional wall switch (see p.10 “Start-up Mode”)

60

74

64

102

side

(CESO)

Perspective view

L N ASL SL SL

SL

PIR OCCUPANCY SWITCHES

Detection diagrams

Dimensions in mm

Wiring diagrams

23

Ceiling directional PIR occupancy switch

Long range Order code: CEDR 6PLR Requires socket, order code: CESO (see page 21)

Long range version

With a long range, narrow detection beam. Designed for corridors and storage aisles.

Specification

Time lag range: 10 seconds to 40 minutes in 9 steps

Photocell range: 100 to 1000 lux, and inactive

Loading: Up to 6 amps (1500W) of resistive, transformer or fluorescent lighting loads, up to 2 amps (500W) of low energy lighting loads (LED lamps and compact fluorescent) or up to 1 amp (250W) of fans or most metal halide lamps

Wiring diagram: See diagrams 23a, 23b, 23c below

Dimensions: See below

DANLERS also manufacture a Long range ceiling flush mounted PIR occupancy switch, order code CEFL PIR LR see page 27 for details.

These directional PIR switches plug into a ceiling mounted socket. The socket can be mounted on a BESA box.

L

load

optional manual wall switch for overriding off

A few CEDR 6PLR230 VAC

L

load

CEDR 6PLR

optional manual wall switch for overriding off

23a. Single CEDR 6PLR

230 VAC

alternative position for optional wall switch (see p.10 “Start-up Mode”)

23b. A few CEDR 6PLR wired in parallel

alternative position for optional wall switch (see p.10 “Start-up Mode”)

23c. Ceiling mounted socket (CESO)

L N SL CEDR 6PLR Not to scale

CESO

BESA box

luminaire

L N

SL

Up to 25m

CEDR 6PLR

Strong Detection Zonei.e. person walking towards PIR

Secondary Detection Zonei.e. person walking across the zone

Up to 10m Up to 25m

CEDR 6PLR

15mUp to 10m

15m

Plan view

Side elevation

CEDR 6PLR

Ideal mounting height between 2.2 and 3m

NN

60

74

64

115

side

(CESO)

CEDR 6PLR can be rotated and lowered

to a 45º angle

Perspective view

L N ASL SL SL

SL

PIR OCCUPANCY SWITCHES

Wiring diagrams

Dimensions in mm

Detection diagrams

2524

BATTEN MOUNT PIR OCCUPANCY SWITCHES

‘Intelligent’ active photocell versions

Ideal for use in factories, warehouses, offices, schools etc.

Unique one touch calibration process removes the site specific addition of artificial light from any decision to automatically switch the lights on/off - eliminates risk of load ‘cycling’ on/off. To maximise on the energy saving potential of the ‘Intelligent’ photocell, these products are recommended for areas with some natural daylight.

If lighting load is ON and ambient light rises above the preset threshold - the load is switched OFF. Inhibits load from switching ON if lux is greater than the preset threshold.

Active photocell operation to maximise energy saving with Overlux timer (passing cloud timer) to minimise unnecessary switching.

Real time photocell status indicator. Test function which switches load on/off when testing.

IP53 rated enclosure.

Specification

Time lag range: 10 seconds to 40 minutes in 9 steps

Photocell range: 100 to 3000 lux (adjustable)

Loading: Up to 10 amps (2500W) of resistive and tungsten. Up to 6 amps (1500W) of fluorescent (switch start) or mains halogen lamps*. *Recommended with integral thermal safety fuse. Up to 3 amps (750W) of electronic or wire wound transformers or compact fluorescent or LED lamps.

Wiring diagram: See diagram 24 below

Dimensions: See below

BMINTPIRSP Spot detection, 1.5 metre at 2.4m - 5m mounting height

BMINTPIR5M 5 metre detection at 2.4m - 5m mounting height

BMINTPIRRH Reduced height version to avoid detection spillage onto lower floors, 2.5 metre detection at 2.5m mounting height)

BMINTPIR10M 10 metre detection at 2.4m - 5m mounting height

These easy to fit controls can be mounted onto the end of lighting battens via the 20mm knock out. 1 metre wire tails to connect to the lighting ballast.

These products have a GB Patent Pending. GB Patent application number 1219746.3

front

50

120

36

105

side

20mmthreadedentry spout

Up to 5m

BMINTPIR5M orBMPIR5M

For optimum coverage recommended mounting height between 2.4 and 5m.

Perspective view of detection zone

Detection zone

100°

Up to 10m

BMINTPIR10M orBMPIR10M

For optimum coverage recommended mounting height between 2.4 and 5m.

Detection zone

112°

Up to 1.5m

BMINTPIRSP orBMPIRSP

For optimum coverage recommended mounting height between 2.4 and 5m.

20°

Dimensions in mm

Detection diagrams

L

load

BMINTPIR (SP, 5M, 10M, RH)

optional manual wall switch for overriding off

24. Single BMINTPIR (SP, 5M, 10M or RH)

230 VAC

N

SLN

Wiring diagram

Order codes: BMINTPIR5M, BMINTPIRRH

Order code: BMINTPIR10M

Order code: BMINTPIRSP

2524

Passive photocell versions

Ideal for use in factories, warehouses, offices, schools etc

Photocell override facility. This is ideal for areas with no natural light such as some warehouses and corridors without external windows.

Switches lights on when somebody is detected. Switches lights off when nobody has been detected for a chosen period. The photocell can be set so that lights do not switch on during the day.

Realtime photocell status indicator (glows green when active or red when inactive).

IP53 rated enclosure.

Specification

Time lag range: 10 seconds to 40 minutes in 9 steps

Photocell range: 100 to 3000 lux (adjustable) and inactive

Loading: Up to 10 amps (2500W) of resistive and tungsten. Up to 6 amps (1500W) of fluorescent (switch start) or mains halogen lamps*. *Recommended with integral thermal safety fuse. Up to 3 amps (750W) of electronic or wire wound transformers or compact fluorescent or LED lamps.

Wiring diagram: See diagram 25 below

Dimensions: See below

BMPIRSP Spot detection, 1.5 metre at 2.4m - 5m mounting height

BMPIR5M 5 metre detection at 2.4m - 5m mounting height

BMPIRRH Reduced height version to avoid detection spillage onto lower floors, 2.5 metre detection at 2.5m mounting height)

BMPIR10M 10 metre detection at 2.4m - 5m mounting height

These easy to fit controls can be mounted onto the end of lighting battens via the 20mm knock out and come with 1 metre wire tails to connect to the lighting ballast.

BATTEN MOUNT PIR OCCUPANCY SWITCHES

front

50

120

36

105

side

20mmthreadedentry spout

Up to 5m

BMINTPIR5M orBMPIR5M

For optimum coverage recommended mounting height between 2.4 and 5m.

Perspective view of detection zone

Detection zone

100°

Up to 10m

BMINTPIR10M orBMPIR10M

For optimum coverage recommended mounting height between 2.4 and 5m.

Detection zone

112°

Up to 1.5m

BMINTPIRSP orBMPIRSP

For optimum coverage recommended mounting height between 2.4 and 5m.

20°

Detection diagrams

Dimensions in mm

L

load

BMINTPIR (SP, 5M, 10M, RH)

optional manual wall switch for overriding off

25. Single BMPIR (SP, 5M, 10M or RH)

230 VAC

N

SLN

Wiring diagram

Order codes: BMPIR5M, BMINTPIRRH

Order code: BMPIR10M

Order code: BMPIRSP

Dimensions in mm Wiring diagrams

26

Batten mounted PIR occupancy switch - IP66 rated

Order code: BMEXPIR

Specification

Weatherproof: IP66 rating

Detection range: Up to 10m

Detection angle: 120°

Time lag: 2 to 20 minutes (adjustable)

Photocell range: 10 lux to infinite lux (adjustable)

Loading: Up to 6 amps (1500W) incandescent or mains halogen lamps. Up to 4 amps (1000W) electronic or wire wound transformers, fluorescent lamps (high frequency or switch start). Up to 2 amps (500W) compact fluorescent or LED lamps. Up to 1 amp (250W) most fans and metal halide discharge lamps.

Wiring diagram: See diagram 26 below

Dimensions: 75 x 60 x 37mm plus 1 metre wire tails

Cost effective, quick and easy to fit PIR occupancy switch designed to fit onto the end of lighting battens.

230 VAC

L

N

load

BMEXPIR

optional manual switch for overriding off

10

65

37

24 24

60

front side

Cablegland

5

17

DANLERS Batten mount PIR occupancy switch can be mounted onto the end of lighting battens via the 20mm knock out. The switch includes the connection 20mm thread and 1 metre of 3-core flex to connect to the lighting ballast.

Ideal for use in factories, warehouses, offices, schools etc., but also wetrooms, damp areas and outdoor environments such as car parks due to its tough IP66 rated enclosure.

Switches lights on when somebody is detected.

Switches lights off when nobody has been detected for a chosen period.

The photocell can be set so that lights do not switch on during the day.

Tough, compact IP66 rated polycarbonate moulding.

7m

Detection zone

7m

50°

100°

BMEXPIR

Side elevation and end elevation

For optimum coveragerecommended mounting height between 2.4 and 5 m

26. Single PIR occupancy switch

SL

PIR OCCUPANCY SWITCHES

Detection diagram

BMEXPIR fitted on the end of a lighting batten.

27

Order code: CEFL PIR LR

Ceiling mounted long range PIR occupancy switch

27a. Single CEFL PIR LR 27b. A few CEFL PIR LR wired in parallel

L

load

optional manual wall switch for overriding off

A few CEFL PIR LR230 VAC alternative

position for optional wall switch (see p.10 “Start-up Mode”)

N

L

load

CEFL PIR LR

optional manual wall switch for overriding off

230 VAC

alternative position for optional wall switch (see p.10 “Start-up Mode”)

N

With a long range, narrow detection beam. Designed for warehouses and storage aisles with a narrow point of access.

CEFL PIR LR is also suitable for building into luminaires.

Specification

Time lag range: 10 seconds to 40 minutes in 9 steps

Photocell range: 100 to 1000 lux, and inactive

Loading: Up to 6 amps (1500W) of resistive, transformer or fluorescent lighting loads, up to 2 amps (500W) of low energy lighting loads (LED lamps and compact fluorescent) or up to 1 amp (250W) of fans or most metal halide lamps

Wiring diagram: See diagrams 27a and 27b below

Dimensions: See below

A photocell override version of the above is available on request.

DANLERS also manufacture a PIR occupancy switch module suitable for mounting onto Eurodata plates with a 12 metre range for storage aisles and warehouses (order code GREUW PIR12E). Please call for further details.

This long range PIR occupancy switch is ideal for storage aisles and high bay applications where a height of up to 20m is required.

55

3

2m cable

60

72

72

side plan

66

Requires 63 or 64mm (2.5") diameter hole in a false or plasterboard ceiling

38

17

CEFL PIR LR

Strong Detection Zonei.e. person moving arm

Secondary Detection Zonei.e. person walking across the zone

Up to 10m

Up to 20m

15m

SL

SL SL SL

PIR OCCUPANCY SWITCHES

Detection diagram

Dimensions in mm Wiring diagrams

28

Wall or ceiling mounted PIR occupancy switch

The WACE PIR is suitable for either wall or ceiling mounting. It fits either into a plaster depth (16mm) wall box or onto a ceiling mounted square pattress box. It requires a neutral wire.

Order code: WACE PIR

Applications

Suitable for stairwells, corridors, toilet lobbies, etc.

Version incorporating override off button, enabling lights to be held off during video presentations etc, available by request.

Specification

Detection angle: 120°

Time lag range: 10 seconds to 40 minutes in 9 steps

Photocell range: 100 to 1000 lux, and inactive

Loading: Up to 6 amps (1500W) of resistive, transformer or fluorescent lighting loads, up to 2 amps (500W) of low energy lighting loads (LED lamps and compact fluorescent) or up to 1 amp (250W) of fans or most metal halide lamps

Wiring diagram: See diagrams 28a and 28b below

Dimensions: 86 x 86 x 22mm. Wall box depth 16mm

28a. Single WACE PIR 28b. A few WACE PIR wired in parallel, eg. in a stairwell

Requires 16mm deep box

Up to 5m Up to 10m

WACE PIR Strong Detection Zone

Secondary Detection Zone 60°

120°

Up to 5m Up to 10m

StrongDetectionZone

SecondaryDetectionZone45°

90° WACE PIR

Up to 5m Up to 10m

WAPIR Strong Detection Zone

Secondary Detection Zone 60°

120°

Up to 5m Up to 10m

Strong Detection Zone

Secondary Detection Zone 45°

90° WAPIR

Strong Detection Zonei.e. person moving arm

Secondary Detection Zonei.e. person walking across the zone

Strong Detection Zonei.e. person moving arm

Secondary Detection Zonei.e. person walking across the zone

Plan view Side elevation

Wall mounted PIR occupancy switch

Ideal mounting height between 1 and 1.8m

L

Nload

A few WACE PIR

230 VAC

load

L

N

WACE PIR

230 VAC

plan side

2286

86

Perspective view

SL

SL SL SL

PIR OCCUPANCY SWITCHES

Dimensions in mm Wiring diagrams

Detection diagrams

29

The WAPIR model replaces an existing wall switch – no neutral wire is needed. It fits into a plaster depth (16mm) wall box. The WAPIR model also has a manual override off switch on the front of the plate.

Wall mounted PIR occupancy switch

Order code: WAPIR

The WAPIR is suitable for small offices, meeting rooms, tutoring rooms, etc. For wall mounting only. The WAPIR is supplied with a load capacitor to augment small loads.

The override off button (out position) enables the lights to be held off during video presentations, etc. A version without the manual override button is also available on request (order code WAPIRX).

Specification

Detection angle: 120°

Time lag range: 10 seconds to 40 minutes in 9 steps

Photocell range: 100 to 1000 lux, and inactive

Maximum load: Up to 6 amps (1500W) of resistive, transformer or fluorescent lighting loads, up to 2 amps (500W) of low energy lighting loads (LED lamps and compact fluorescent) or up to 1 amp (250W) of fans or most metal halide lamps

Minimum load: 40W resistive or approximately 100W inductive per WAPIR in the circuit. A load capacitor (CAPLOAD) is supplied to augment small loads.

Wiring diagram: See diagrams 29a and 29b below

Dimensions: 86 x 86 x 22mm. Wall box depth 16mm

NOTE: Because WAPIR requires a permanent live supply the following restrictions apply: - WAPIR should only be used in applications where the lights would not be ON for

more time than they are OFF. This is to allow its rechargeable battery enough time to recharge itself from the mains supply.

- Wiring WAPIR’s in parallel will increase the ON status of a load and therefore the battery may not have sufficient time to recharge.

- The load MUST be able to pass parasitic current. The battery may not charge with some low energy / high efficiency luminaire products that do not pass sufficient parasitic current.

- If power factor correction capacitors are inbuilt to the luminaire, it is not advised to add additional CAPLOADs to the switching circuit.

29a. Single WAPIR 29b. A few WAPIR wired in parallelRequires 16mm deep wall box

Up to 5m Up to 10m

WACE PIR Strong Detection Zone

Secondary Detection Zone 60°

120°

Up to 5m Up to 10m

StrongDetectionZone

SecondaryDetectionZone45°

90° WACE PIR

Up to 5m Up to 10m

WAPIR Strong Detection Zone

Secondary Detection Zone 60°

120°

Up to 5m Up to 10m

Strong Detection Zone

Secondary Detection Zone 45°

90° WAPIR

Strong Detection Zonei.e. person moving arm

Secondary Detection Zonei.e. person walking across the zone

Strong Detection Zonei.e. person moving arm

Secondary Detection Zonei.e. person walking across the zone

Plan view Side elevation

Wall mounted PIR occupancy switch

Ideal mounting height between 1 and 1.8m

L

Nload

WAPIR WAPIR WAPIR

230 VAC

L

N

230 VAC

load

WAPIRplan side

2286

86

Perspective view

SL

SL SLSL

PIR OCCUPANCY SWITCHES

Dimensions in mm Wiring diagrams

Detection diagrams

These modules are suitable for mounting onto Eurodata plates and fit into a 35mm deep wall box. They are also suitable for building into luminaires (see page 76 for fixing bezel). They require a neutral wire.

Order code: GREUW PIR5X

5m detection - concealed adjustment spindles

Adjustment spindles hidden behind front surface lid for a neat finish (module must be removed from wall plate or luminaire to adjust). Can be suited in with other Eurodata modules.

Specification

Detection zone: 360°

Detection angle: 100°

Time lag range: 10 seconds to 40 minutes in 9 steps

Photocell range: 15 to 1000 lux, and inactive

Loading: Up to 6 amps (1500W) of resistive, transformer or fluorescent lighting loads, up to 2 amps (500W) of low energy lighting loads (LED lamps and compact fluorescent) or up to 1 amp (250W) of fans or most metal halide lamps

Wiring diagram: See diagrams 30a and 30b below

Dimensions: 50 x 25 x 38mm, minimum wall box depth of 35mm

30a. Single PIR occupancy switch module 30b. A few PIR occupancy switch modules wired in parallel, eg. in a stairwell

L

Nload

A few PIR occupancy switch modules

230 VAC

load

L

N

PIR occupancy switch module

230 VAC

30

Dimensions in mm GREUW PIR5X, GREUW PIR5E. Requires wall box depth of 35mm

3825

50

front side

Order code: GREUW PIR5E

5m detection - visible adjustment spindles

Adjustment spindles visible on front surface for quick and convenient adjustment. Can be suited in with other Eurodata modules.

Specification

Detection zone: 360°

Detection angle: 100°

Time lag range: 10 seconds to 40 minutes in 9 steps

Photocell range: 15 to 1000 lux, and inactive

Loading: Up to 6 amps (1500W) of resistive, transformer or fluorescent lighting loads, up to 2 amps (500W) of low energy lighting loads (LED lamps and compact fluorescent) or up to 1 amp (250W) of fans or most metal halide lamps

Wiring diagram: See diagrams 30a and 30b below

Dimensions: 50 x 25 x 38mm, minimum wall box depth of 35mm

Up to 7m

GREUW PIR5X or GREUW PIR5E

Detection zone

For optimum coveragerecommended mounting height between 2.4 and 5m

Up to5m

Plan view (wall mounted)

GREUW PIR5X or GREUW PIR5E

Side elevation (wall mounted)

GREUW PIR5X or GREUW PIR5E

Perspective view (ceiling mounted)

Up to 5m

DetectionZone40°

80°

Up to 5m

DetectionZone50°

100°

SL

SL SL SL

PIR OCCUPANCY SWITCH MODULES

Dimensions in mm Wiring diagrams

Detection diagrams

These modules are suitable for ceiling mounting onto Eurodata plates. They are also suitable for building into luminaires (see page 76 for fixing bezel). They require a neutral wire. These versions are best suited for use in areas such as warehouses, sports halls and circulation areas, where there is likely to be a significant level of movement.

Order code: GREUW PIR10X

10m detection - concealed adjustment spindles

Adjustment spindles hidden behind front surface lid for a neat finish (module must be removed from plate or luminaire to adjust). Can be suited in with other Eurodata modules.

Specification

Detection zone: 360°

Time lag range: 10 seconds to 40 minutes in 9 steps

Photocell range: 15 to 1000 lux, and inactive

Loading: Up to 6 amps (1500W) of resistive, transformer or fluorescent lighting loads, up to 2 amps (500W) of low energy lighting loads (LED lamps and compact fluorescent) or up to 1 amp (250W) of fans or most metal halide lamps

Wiring diagram: See diagrams 31a and 31b below

Dimensions: 50 x 25 x 38mm, minimum back box depth of 35mm

A photocell override version is available on request.

31a. Single PIR occupancy switch module 31b. A few PIR occupancy switch modules wired in parallel, eg. in a stairwell

L

Nload

A few PIR occupancy switch modules

230 VAC

load

L

N

PIR occupancy switch module

230 VAC

Dimensions in mm GREUW PIR10X, GREUW PIR10E. Requires back box depth of 35mm

3825

50

front side

Order code: GREUW PIR10E

31

10m detection - visible adjustment spindles

Adjustment spindles visible on front surface for quick and convenient adjustment. Suitable for mounting onto a Eurodata plate. Can be suited in with other Eurodata modules.

Specification

Detection zone: 360°

Time lag range: 10 seconds to 40 minutes in 9 steps

Photocell range: 15 to 1000 lux, and inactive

Loading: Up to 6 amps (1500W) of resistive, transformer or fluorescent lighting loads, up to 2 amps (500W) of low energy lighting loads (LED lamps and compact fluorescent) or up to 1 amp (250W) of fans or most metal halide lamps

Wiring diagram: See diagrams 31a and 31b below

Dimensions: 50 x 25 x 38mm, minimum back box depth of 35mm

A photocell override version is available on request.

Up to 15m

GREUW PIR10X or GREUW PIR10E

Detection zone

For optimum coveragerecommended mounting height between 5 and 10m

Up to12m

Perspective view (ceiling mounted)

optional manual wall switch for overriding off

SL

SL SL SL

PIR OCCUPANCY SWITCH MODULES

Dimensions in mm Wiring diagrams

Detection diagram 12 metre (mounting height) versions of the above are available on request (order codes: GREUWPIR12E and GREUWPIR12X).


Recommended