Planning for Workplace Emergencies
OSHA requires employers to develop and maintain emergency action plans and fire prevention plans to help ensure their employees are protected and to minimize prop-erty loss due to emergency situations. This two-hour course is an introduction to three emergency preparedness topics: the elements of an effective Emergency Action Plan (EAP), exit route requirements, and the Fire Prevention and Protection Plan (FPP).
This page intentionally blank
OSHAcademy Course 629 Study Guide
Planning for Workplace Emergencies
Copyright © 2018 Geigle Safety Group, Inc.
No portion of this text may be reprinted for other than personal use. Any commercial use of this document is strictly forbidden.
Contact OSHAcademy to arrange for use as a training document.
This study guide is designed to be reviewed off-line as a tool for preparation to successfully complete OSHAcademy Course 629.
Read each module, answer the quiz questions, and submit the quiz questions online through the course webpage. You can print the post-quiz response screen which will contain the correct answers to the questions.
The final exam will consist of questions developed from the course content and module quizzes.
We hope you enjoy the course and if you have any questions, feel free to email or call:
OSHAcademy
15220 NW Greenbrier Parkway, Suite 230 Beaverton, Oregon 97006 www.oshatrain.org [email protected] +1 (888) 668-9079
Disclaimer
This document does not constitute legal advice. Consult with your own company counsel for advice on compliance with all applicable state and
federal regulations. Neither Geigle Safety Group, Inc., nor any of its employees, subcontractors, consultants, committees, or other assignees
make any warranty or representation, either express or implied, with respect to the accuracy, completeness, or usefulness of the information
contained herein, or assume any liability or responsibility for any use, or the results of such use, of any information or process disclosed in this
publication. GEIGLE SAFETY GROUP, INC., DISCLAIMS ALL OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING, WITHOUT LIMITATION, ANY
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Taking actions suggested in this document does not guarantee
that an employer, employee, operator or contractor will be in compliance with applicable regulations. Ultimately every company is responsible
for determining the applicability of the information in this document to its own operations. Each employer’s safety management system will be
different. Mapping safety and environmental management policies, procedures, or operations using this document does not guarantee
compliance regulatory requirements.
This page intentionally blank
Course 629
Contents
Modules and Learning Objectives .................................................................................................. 1
Course Introduction ........................................................................................................................ 3
Module 1: Emergency Action Plan (EAP) ........................................................................................ 4
Introduction ................................................................................................................................ 4
Do you need an EAP? .................................................................................................................. 5
Elements of the EAP ................................................................................................................ 5
Reporting Emergencies ............................................................................................................... 6
Evacuation Procedures ............................................................................................................... 7
Designate Evacuation Coordinators ........................................................................................... 8
Assisting Others to Evacuate ...................................................................................................... 9
Employees Who May Remain to Shut Down ............................................................................ 10
Accounting for Employees ........................................................................................................ 11
Active Shooter Emergencies ..................................................................................................... 12
How to Respond to Active Shooter Emergencies ................................................................. 12
Fire, Rescue, and Medical Services ........................................................................................... 15
Module 2: Exit Route Requirements ............................................................................................. 16
Basic Requirements .................................................................................................................. 16
Number of Exits......................................................................................................................... 17
Exit Discharge ............................................................................................................................ 18
Locking Arrangements .............................................................................................................. 18
Door Swing ................................................................................................................................ 19
Exit Route Capacity ................................................................................................................... 19
Height and Width Requirements .............................................................................................. 20
Course 629
Outdoor Exit Routes .................................................................................................................. 20
Module 3: Fire Prevention and Protection Plans .......................................................................... 22
Introduction .............................................................................................................................. 22
FPP Responsibilities .................................................................................................................. 23
Management ......................................................................................................................... 23
Plan Administrator ................................................................................................................ 23
Supervisors ............................................................................................................................ 23
Employees ............................................................................................................................. 23
Written Plan Components ........................................................................................................ 24
FPP Best Practices ................................................................................................................. 25
Hazards that Cause Fires ........................................................................................................... 26
Electrical Hazards .................................................................................................................. 26
Portable Heaters ................................................................................................................... 26
Office Fires Hazards .............................................................................................................. 26
Welding, Cutting, and Open Flame Work ............................................................................. 26
Flammable and Combustible Materials ................................................................................ 26
Smoking in the Workplace .................................................................................................... 27
Fire Extinguishing Systems ........................................................................................................ 27
Fixed Extinguishing Systems ................................................................................................. 27
Portable Extinguishing Systems ............................................................................................ 28
How to Use a Fire Extinguisher ................................................................................................. 28
FPP Training Requirements ....................................................................................................... 29
Additional Resources .................................................................................................................... 31
Course 629
Copyright © 2018 Geigle Safety Group, Inc. Page 1 of 31
Modules and Learning Objectives
Module 1: The Emergency Action Plan (EAP)
Learning objectives in this module include:
• List key elements in the Emergency Action Plan (EAP).
• Discuss reporting requirements under the EAP.
• Describe a typical evacuation procedure if a fire occurs.
• Describe evacuation warden requirements and duties.
• Discuss requirements for employees who do not evacuate.
• Discuss requirements for accounting for employees and assembly areas.
• Describe how individuals can respond in an active shooter emergency.
• Identify important points when coordinating with fire, rescue, and medical services.
Module 2: Exit Route Requirements
Learning objectives in this module include:
• Define the terms "exit," "exit access," and "exit discharge."
• Describe the basic requirements for exit design, location, and use.
• Discuss the factors that determine the number of exits.
• Describe the requirements for door swing, locking, and outside exit doors.
• Describe the importance of training and retraining proper use of exits during
emergencies.
Module 3: Fire Prevention and Protection Plans
Learning objectives in this module include:
Course 629
Copyright © 2018 Geigle Safety Group, Inc. Page 2 of 31
• Describe responsibilities for Fire Prevention Plan (FPP) managers and administrators.
• Discuss FPP responsibilities for supervisors and employees.
• Describe the requirement for a written FPP and identify components.
• Identify at least five best practices under the FPP.
• Identify and describe the two primary types of fire extinguishing systems.
• Describe the PASS method for using fire extinguishers.
• List and give examples of the various fire hazards in the workplace.
• Describe FPP education and training requirements for managers, supervisors, and
employees.
Course 629
Copyright © 2018 Geigle Safety Group, Inc. Page 3 of 31
Course Introduction
Several Occupational Safety and Health Administration (OSHA) standards explicitly require
employers to have Emergency Action Plans (EAPs) for their workplaces. Emergency
preparedness is a well-known concept in protecting workers' safety and health. To help
employers, safety and health professionals, training directors, and others, the OSHA
requirements for emergencies are compiled and summarized in this course.
Fire safety becomes everyone's job at a worksite. Employers must develop Fire Prevention
Plans (FPPs) and train workers about fire hazards in the workplace and what to do in a fire
emergency. If you want your workers to evacuate, you should train them on how to escape. If
you expect your workers to use firefighting equipment, you must give them appropriate
equipment and train them to use the equipment safely.
More information on this topic may be seen in the following OSHAcademy courses: The
Emergency Action Plan (See course 717), Fire Prevention and Protection Plan (See course 718),
along with a Violence Prevention Plan (See course 720). These three plans should be integrated
into an overall Emergency Preparedness Program to protect employees and help ensure
continuity of the organization's business services.
This course provides an overview of OSHA standards for emergencies contained within OSHA
1910.38, Emergency Action Plans, and 1910.39, Fire Prevention Plans. It is not intended to alter
or determine compliance responsibilities in OSHA standards or the Occupational Safety and
Health Act of 1970. Please review the current OSHA standards applicable to your work
operations to ensure your compliance.
Course 629
Copyright © 2018 Geigle Safety Group, Inc. Page 4 of 31
Module 1: Emergency Action Plan (EAP)
Introduction
How would you escape from your workplace in an emergency? Do you know where all the exits
are in case your first choice is too crowded? Are you sure the doors will be unlocked and the
exit route, such as a hallway, will not be blocked during a fire, explosion, or other crisis?
Knowing the answers to these questions could keep you safe during an emergency.
An emergency action plan (EAP) is a written document required by OSHA standard 1910.38. The
purpose of an EAP is to facilitate and organize employer and employee actions during
workplace emergencies.
Well-developed emergency plans and proper employee training (such that employees
understand their roles and responsibilities within the plan) will result in fewer and less severe
employee injuries and less structural damage to the facility during emergencies. A poorly
prepared plan, likely will lead to a disorganized evacuation or emergency response, resulting in
confusion, injury, and property damage.
Emergency action plans must be written. However, for smaller companies, the plan does not
need to be written and may be communicated orally if there are 10 or fewer employees.
Quiz Instructions
After each section, there is a quiz question. Make sure to read the material in each section to
discover the correct answer to these questions. Circle the correct answer. When you are
finished go online to take the final exam. This exam is open book, so you can use this study
guide.
1. The Emergency Action Plan (EAP) may be written or communicated orally if there are
fewer than _____ employees.
a. 5 b. 10 c. 15 d. 20
Course 629
Copyright © 2018 Geigle Safety Group, Inc. Page 5 of 31
Do you need an EAP?
Your company may be required by OSHA to establish an Emergency Action Plan (EAP) if you
meet certain criteria. Check out the diagram to the right to see if your company needs an EAP.
You can also find more information on establishing an EAP from OSHA Pub 2088, How to Plan
for Workplace Emergencies and Evacuations.
Elements of the EAP
At a minimum, the plan must include but is not limited to the following elements:
• Means of reporting fires and other emergencies,
• Evacuation procedures and emergency escape route assignments,
• Procedures for employees who remain to operate critical plant operations before they
evacuate,
• Accounting for all employees after an emergency evacuation has been completed,
• Rescue and medical duties for employees performing them, and
• Names or job titles of persons who can be contacted.
Although they are not specifically required by OSHA, employers may find it helpful to include
the following in the EAP:
• A description of the alarm system to be used to notify employees (including disabled
employees) to evacuate and/or take other actions. The alarms used for different actions
should be distinctive and might include horn blasts, sirens, or even public address
systems.
• The site of an alternative communications center to be used in the event of a fire or
explosion.
• A secure on- or offsite location to store originals or duplicate copies of accounting
records, legal documents, your employees' emergency contact lists, and other essential
records.
Course 629
Copyright © 2018 Geigle Safety Group, Inc. Page 6 of 31
2. Which of the following is a MANDATORY element in the Emergency Action Plan (EAP)?
a. Alternate communications center b. Description of alarm systems c. Means of reporting fires and other emergencies d. Secure offsite storage areas
Reporting Emergencies
Employees must know how to report emergencies. Some use internal telephone numbers,
intercom, or public address systems to notify other employees. It is important for employees to
also notify the proper authorities such as fire, medical, or rescue services, if your company
relies on this type of assistance during an emergency.
There are preferred procedures for reporting emergencies such as dialing 911, or an internal
emergency number, or pulling a manual fire alarm but there are many other possibilities.
• Dialing "911" is a common method for reporting emergencies if external emergency
personnel are used at your workplace.
• Internal numbers may be used for reporting emergencies. If they are, they should be
posted on, or near, each phone. Internal numbers sometimes are connected to intercom
systems so that coded announcements may be made.
• Employees may be requested to activate manual pull stations or other alarm systems.
No matter what system is used, it is imperative emergency situations be immediately reported.
Fires and other emergency situations can reach dangerous levels in seconds and any delay in
getting emergency responders to the scene can result in additional loss of life and property.
3. Which of the following are common methods of reporting emergencies in the
workplace?
a. Dialing 911, internal phone numbers, and manual alarms b. Cell phones, shortwave radio, and external numbers c. VOIP calls, cell phones, and visual alarms d. Radio communications, intercoms, and local emergency numbers
Course 629
Copyright © 2018 Geigle Safety Group, Inc. Page 7 of 31
Evacuation Procedures
Evacuation policies, procedures, and escape route assignments are put into place so that
employees understand who is authorized to order an evacuation, under what conditions an
evacuation would be necessary, how to evacuate, and what routes to take. Exit diagrams are
typically used to identify the escape routes to be followed by employees from each specific
facility location.
Evacuation procedures also often describe actions employees should take before and while
evacuating such as shutting windows, turning off equipment, and closing doors behind them.
Under the typical EAP, the employer will expect all employees to evacuate in an emergency.
However, sometimes a critical decision may need to be made when planning - whether
employees should be trained and responsible for extinguishing small (controllable) fires.
A disorganized evacuation can result in confusion, injury, and property damage. When
developing the emergency action plan, it is important to determine the following:
• conditions under which an evacuation would be necessary
• conditions under which it may be better to shelter-in-place
• a clear chain of command and designation of the person in your business authorized to
order an evacuation or shutdown
• specific evacuation procedures, including routes and exits
• specific evacuation procedures for high-rise buildings for employers and employees
• procedures for assisting visitors and employees to evacuate, particularly those with
disabilities or who do not speak English
• designation of what, if any, employees will remain after the evacuation alarm to shut
down critical operations or perform other duties before evacuating
• a means of accounting for employees after an evacuation
• special equipment for employees
• appropriate respirators
Course 629
Copyright © 2018 Geigle Safety Group, Inc. Page 8 of 31
During development and implementation of your draft plan, think about all possible emergency
situations and evaluate your workplace to see if it complies with OSHA's emergency standards.
4. Under the typical Emergency Action Plan (EAP), the employer may assign some
employees to _____.
a. aggressively respond to uncontrollable releases of hazardous substances b. fight all fires, no matter how big they are c. extinguish small fires that are controllable d. attempt rescue of trapped employees
Designate Evacuation Coordinators
When drafting your emergency action plan, you may wish to select a responsible individual to
lead and coordinate your emergency plan and evacuation. It is critical that employees know
who the coordinator is and understand that person has the authority to make decisions during
emergencies.
The coordinator should be responsible for the following:
• Assessing the situation to determine whether an emergency exists requiring activation
of your emergency procedures;
• Supervising all efforts in the area, including evacuating personnel;
• Coordinating outside emergency services, such as medical aid and local fire
departments, and ensuring they are available and notified when necessary; and
• Directing the shutdown of plant operations when required.
You also may find it beneficial to coordinate the action plan with other employers when several
employers share the worksite, although OSHA standards do not specifically require this.
Course 629
Copyright © 2018 Geigle Safety Group, Inc. Page 9 of 31
5. In an effective Emergency Action Plan, who is designated as the person responsible for
coordinating outside emergency services and ensuring that they are available and notified
when necessary?
a. Safety managers b. Firefighting teams c. Evacuation wardens d. Evacuation coordinators
Assisting Others to Evacuate
Many employers designate individuals as evacuation wardens to help move employees from
danger to safe areas during an emergency. Generally, one evacuation warden for every 20
employees should be adequate, and the appropriate number of wardens should be available at
all times during working hours.
Evacuation wardens may be responsible for checking offices, bathrooms, and other spaces
before being the last person to exit an area. They might also be tasked with ensuring that fire
doors are closed when exiting.
Employees designated to assist in emergency evacuation procedures should:
• be trained in the complete workplace layout and various alternative escape routes if the
primary evacuation route becomes blocked, and
• be made aware of employees with special needs (who may require extra assistance
during an evacuation), how to use the buddy system, and any hazardous areas to avoid
during an emergency evacuation.
Visitors also should be accounted for following an evacuation and may need additional
assistance when exiting. Some employers have all visitors and contractors sign in when entering
the workplace and use this list when accounting for all persons in the assembly area. The hosts
and/or area wardens, if established, are often tasked with helping these individuals safely
evacuate.
Course 629
Copyright © 2018 Geigle Safety Group, Inc. Page 10 of 31
6. Generally, how many available evacuation wardens is considered adequate during work
hours?
a. Two on each floor of the building b. One for every 20 employees c. Two for every 10 employees d. One for each department
Employees Who May Remain to Shut Down
Large companies may have certain equipment and processes that must be shut down in stages
or over time. In other instances, it is not possible or practical for employees to stay behind to
shut down equipment or processes under emergency situations and everyone must evacuate.
However, smaller enterprises may require designated employees to remain behind briefly to
operate fire extinguishers or shut down gas and/or electrical systems and other special
equipment that could be damaged if left operating or create additional hazards to emergency
responders (such as releasing hazardous materials).
Each employer must review their operation and determine whether total and immediate
evacuation is possible for various types of emergencies. The preferred approach, and the one
most often taken by small enterprises, is immediate evacuation of all their employees when the
evacuation alarm is sounded.
If any employees will stay behind, the plan must describe in detail the procedures to be
followed by these employees.
• All employees remaining behind must be capable of recognizing when to abandon the
operation or task and evacuate themselves before their egress path is blocked.
• In small establishments it is common to include in the plan locations where utilities
(such as electrical and gas) can be shut down for all or part of the facility either by
company employees or by emergency response personnel.
Course 629
Copyright © 2018 Geigle Safety Group, Inc. Page 11 of 31
7. Why are some employees designated to stay behind and not evacuate immediately
when an emergency occurs?
a. They are responsible for looking for stragglers b. They will aggressively attack all releases of hazardous substances c. They may be needed for contain and clean up hazardous substances d. They may operate fire extinguishers, shut-off valves, and breakers
Accounting for Employees
Procedures to account for employees after the evacuation to ensure that everyone got out may
include designating employees to sweep areas, checking offices and restrooms before being the
last to leave a workplace or conducting a roll call in the assembly area. Evacuation wardens can
be helpful in accounting for employees. To ensure the fastest, most accurate accounting of
employees, consider including these steps in the EAP:
• Designate assembly areas or areas Assembly areas, both inside and outside the
workplace, are the locations where employees gather after evacuating.
o Internal assembly areas within the building are often referred to as "areas of
refuge." Make sure the assembly area has sufficient space to accommodate all
employees.
o Exterior assembly areas, used when the building must be partially or completely
evacuated, are typically located in parking lots or other open areas away from
busy streets. Try and designate assembly areas so that employees will be up-
wind of the building.
• Take a head count after the evacuation. Accounting for all employees following an
evacuation is critical. Identify the names and last known locations of anyone not
accounted for and pass them to the official in charge.
• Assembly area design. When designating an assembly area, consider (and try to
minimize) the possibility of employees interfering with rescue operations.
• Account for others. Establish a method for accounting for non-employees such as
suppliers and customers.
Course 629
Copyright © 2018 Geigle Safety Group, Inc. Page 12 of 31
• Additional evacuation. Establish procedures for further evacuation in case the incident
expands. This may consist of sending employees home by normal means or providing
them with transportation to an offsite location.
8. What two types of assembly areas are common in Emergency Action Plans (EAPs)?
a. Internal and External b. Specific and General c. Upwind and Downwind d. On-site and off-site
Active Shooter Emergencies
Although not originally considered as part of the emergency action plan, it's now important to
include training with exercises to plan for the event an active shooter is discovered in the
workplace. Together, the EAP and training exercises will prepare your staff to effectively
respond and help minimize loss of life.
An active shooter is an individual actively engaged in killing or attempting to kill people in a
confined and populated area; in most cases, active shooters use firearm(s) and there is no
pattern or method to their selection of victims.
Active shooter situations are unpredictable and evolve quickly. Typically, the immediate
deployment of law enforcement is required to stop the shooting and mitigate harm to victims.
Because active shooter situations are often over within 10 to 15 minutes, before law
enforcement arrives on the scene, individuals must be prepared both mentally and physically to
deal with an active shooter situation.
How to Respond to Active Shooter Emergencies
Quickly determine the most reasonable way to protect your own life. Remember that
customers and clients are likely to follow the lead of employees and managers during an active
shooter situation. The Department of Homeland Security recommends you take the following
actions:
1. Evacuate: If there is an accessible escape path, attempt to evacuate the premises. Be sure to:
• Have an escape route and plan in mind.
• Evacuate regardless of whether others agree to follow.
Course 629
Copyright © 2018 Geigle Safety Group, Inc. Page 13 of 31
• Leave your belongings behind.
• Help others escape, if possible.
• Prevent individuals from entering an area where the active shooter may be.
• Keep your hands visible.
• Follow the instructions of any police officers.
• Do not attempt to move wounded people.
• Call 911 when you are safe.
Continue to the next section for more information on how to respond to an active shooter
emergency.
9. You must have an active shooter plan because an active shooter emergency _____.
a. is usually over within 10 to 15 minutes b. is very likely in your workplace c. usually ends up with multiple injuries and fatalities d. is not a recognized OSHA concern
2. Hide out. If evacuation is not possible, find a place to hide where the active shooter is less
likely to find you.
Your hiding place should:
• Be out of the active shooter’s view.
• Provide protection if shots are fired in your direction (i.e., an office with a closed and
locked door).
• Not trap you or restrict your options for movement.
To prevent an active shooter from entering your hiding place:
• Lock the door.
• Blockade the door with heavy furniture.
Course 629
Copyright © 2018 Geigle Safety Group, Inc. Page 14 of 31
If the active shooter is nearby:
• Lock the door.
• Silence your cell phone and/or pager.
• Turn off any source of noise (i.e., radios, televisions).
• Hide behind large items (i.e., cabinets, desks).
• Remain quiet.
If evacuation and hiding out are not possible:
• Remain calm.
• Dial 911, if possible, to alert police to the active shooter’s location.
• If you cannot speak, leave the line open and allow the dispatcher to listen.
3. Take action against the active shooter. As a last resort, and only when your life is in
imminent danger, DHS recommends that you attempt to disrupt and/or incapacitate the active
shooter by:
• acting as aggressively as possible against him/her
• throwing items and improvising weapons
• yelling
• committing to your actions
10. According to the Department of Homeland Security, you should confront an active
shooter _____.
a. before he or she has a chance to begin shooting b. only as a last resort and imminent danger c. if you cannot find a hiding place d. if others are in danger and no one has a firearm
Course 629
Copyright © 2018 Geigle Safety Group, Inc. Page 15 of 31
Fire, Rescue, and Medical Services
Although most of us quickly move away from the hazardous environments created during
emergency situations, a group of dedicated and well-trained professional emergency
responders and medical service personnel are tasked with containing and mitigating these
incidents, rescuing individuals at-risk, and providing medical assistance to the injured.
Unless the company is a large employer handling hazardous materials and processes or has
employees regularly working in hazardous situations, the company will probably choose to rely
on local public resources to provide these specialized services.
If external departments or agencies, such as the local fire and police departments, medical
clinics or hospitals, and ambulance services, are used, make sure they are prepared to respond
as outlined in the EAP. Make sure they are familiar with the building and any dangerous
locations within the building.
11. What should be confirmed when external agencies are used to respond to the
company's EAP?
a. They must be familiar with the building and dangerous locations b. They must be approved by the local community response team c. They must be able to respond within 15 minutes of the emergency d. They must practice response procedures at least quarterly
Course 629
Copyright © 2018 Geigle Safety Group, Inc. Page 16 of 31
Module 2: Exit Route Requirements
For an Emergency Action Plan to work, it's important that thought and planning is given to exit
routes. An exit route is a continuous and unobstructed path of exit travel from any point within
a workplace to a place of safety. An exit route consists of three parts:
1. Exit access - 29 CFR 1910.36(a)(3) portion of an exit route that leads to an exit.
2. Exit - portion of an exit route that is generally separated from other areas to provide a
protected way of travel to the exit discharge.
3. Exit discharge - part of the exit route that leads directly outside or to a street, walkway,
refuge area, public way, or open space with access to the outside.
Check out this short video that covers exit routes and emergency action plans.
1. Which of the following are criteria for exit routes?
a. There must open inward from the outside b. They must be numerous and properly color-coded c. They must be continuous and unobstructed d. There must be one exit for each 10 employees
Basic Requirements
The following are basic requirements for exit routes in the workplace:
• An exit route must be permanent. Each exit route must be a permanent part of the
workplace.
• An exit must be separated by fire resistant materials. Construction materials used to
separate an exit from other parts of the workplace must have a one-hour fire resistance
rating if the exit connects three or fewer stories and a two-hour fire resistance-rating if
the exit connects four or more stories.
• Openings into an exit must be limited. An exit is permitted to have only those openings
necessary to allow access to the exit from occupied areas of the workplace, or to the
exit discharge.
Course 629
Copyright © 2018 Geigle Safety Group, Inc. Page 17 of 31
• Opening must be protected. An opening into an exit must be protected by a self-closing
fire door that remains closed or automatically closes in an emergency upon the
sounding of a fire alarm or employee alarm system. Each fire door, including its frame
and hardware, must be listed or approved by a nationally recognized testing laboratory.
2. Exits must be constructed with materials that have _________ if they connect three or
fewer stories in a building.
a. non-flammable properties b. a one-hour fire resistance rating c. four-hour breakthrough time d. 30-minute penetration rating
Number of Exits
The following are basic requirements for the number and location of exits in the workplace:
• The number of exit routes should be adequate.
• At least two exit routes should be available in a workplace to permit prompt evacuation
of employees and other building occupants during an emergency.
• The exit routes should be located as far away as practical from each other so that if one
exit route is blocked by fire or smoke, employees can evacuate using the second exit
route.
• More than two exit routes should be available in a workplace if the number of
employees, the size of the building, its occupancy, or the arrangement of the workplace
is such that all employees would not be able to evacuate safely during an emergency.
• A single exit route is permitted where the number of employees, the size of the building,
its occupancy, or the arrangement of the workplace is such that all employees would be
able to evacuate safely during an emergency.
For assistance in determining the number of exit routes necessary for your workplace, consult
NFPA 101, Life Safety Code.
Course 629
Copyright © 2018 Geigle Safety Group, Inc. Page 18 of 31
3. What determines the number of exits that must be available in a building?
a. NFPA 1910.150, Chapter 7, Ingress and Egress b. The number of employees within a specific worksite c. The ability of all employees to evacuate safely in an emergency d. The type and nature of the building construction
Exit Discharge
The following are requirements for exit discharge:
• Each exit discharge must lead directly outside or to a street, walkway, refuge area,
public way, or open space with access to the outside.
• The street, walkway, refuge area, public way, or open space to which an exit discharge
leads should be large enough to accommodate the building occupants likely to use the
exit route.
• Exit stairs that continue beyond the level on which the exit discharge is located should
be interrupted at that level by doors, partitions, or other effective means that clearly
indicate the direction of travel leading to the exit discharge.
4. Each exit discharge must lead _____.
a. eventually to an outside space or fire-protected room b. directly outside or open space with access to the outside c. to a location that allows employees to access an outside space d. into a safe space with the building or to the outside
Locking Arrangements
The following are requirements for exit door locking arrangements:
• An exit door should be unlocked from the inside.
• Employees should be able to open an exit route door from the inside at all times
without keys, tools, or special knowledge.
• A device such as a panic bar that locks only from the outside is permitted on exit
discharge doors.
Course 629
Copyright © 2018 Geigle Safety Group, Inc. Page 19 of 31
• Exit route doors should be free of any device or alarm that could restrict emergency use
of the exit route if the device or alarm fails.
• An exit route door may be locked from the inside only in mental, penal, or correctional
facilities and then only if supervisory personnel are continuously on duty and the
employer has a plan to remove occupants from the facility during an emergency.
5. When may exit doors be locked?
a. Never, with no exceptions b. In any facility as long as a supervisor is present c. At commercial food facilities with 24/7 workshifts d. At correctional facilities when continuously supervised
Door Swing
The following are requirements related to exit door swing:
• A side-hinged exit door should be used.
• A side-hinged door should be used to connect any room to an exit route.
• The door that connects any room to an exit route must swing out in the direction of exit
travel if the room is designed to be occupied by more than 50 people or if the room is a
high hazard area (i.e., contains contents that are likely to burn with extreme rapidity or
explode).
Exit Route Capacity
• The capacity of an exit route should be adequate.
• Exit routes must support the maximum permitted occupant load for each floor served.
• The capacity of an exit route may not decrease in the direction of exit route travel to the
exit discharge.
Course 629
Copyright © 2018 Geigle Safety Group, Inc. Page 20 of 31
6. The door that connects a room to an exit route must swing out in the direction of exit
travel if the room _____.
a. is capable of holding all evacuees in an emergency b. can occupy more than 50 people or is a high hazard area c. is between the door and the exit discharge d. is regulated by the NFPA
Height and Width Requirements
• An exit route must meet minimum height and width requirements.
• The ceiling of an exit route should be at least seven feet six inches (2.3 m) high. Any
projection from the ceiling must not reach a point less than six feet eight inches (2.0 m)
from the floor.
• An exit access should be at least 28 inches (71.1 cm) wide at all points. Where there is
only one exit access leading to an exit or exit discharge, the width of the exit and exit
discharge should be at least equal to the width of the exit access.
• The width of an exit route should be sufficient to accommodate the maximum
permitted occupant load of each floor served by the exit route.
• Objects that project into the exit route must not reduce the width of the exit route to
less than the minimum width requirements for exit routes.
7. What is the minimum width of an exit route?
a. 28 inches b. 30 inches c. 36 inches d. 42 inches
Outdoor Exit Routes
• An outdoor exit route must have guardrails to protect unenclosed sides if a fall hazard
exists.
Course 629
Copyright © 2018 Geigle Safety Group, Inc. Page 21 of 31
• The outdoor exit route should be covered if snow or ice is likely to accumulate along the
route, unless the employer can demonstrate that any snow or ice accumulation will be
removed before it presents a slipping hazard.
• The outdoor exit route should be reasonably straight and have smooth, solid,
substantially level walkways.
• The outdoor exit route must not have a dead-end that is longer than 20 feet (6.2 m).
8. An outdoor exit route must _____.
a. have a supply of deicer in case of snow or ice accumulation b. not have more than three 90-degree redirections c. not have a dead-end longer than 20 feet d. have guards if a fall hazard of 10 feet or more exists
Course 629
Copyright © 2018 Geigle Safety Group, Inc. Page 22 of 31
Module 3: Fire Prevention and Protection Plans
Introduction
The most important reason to have a Fire Prevention Plan (FPP) is to eliminate the causes of
fire, prevent loss of life, and prevent loss of property by fire. The FPP should be developed to
comply with the OSHA standard 29 CFR 1910.39, Fire Prevention Plans. An effective FPP does all
of the following:
• It provides employees with information and guidelines that will assist them in
recognizing, reporting, and controlling fire hazards.
• It identifies materials that are potential fire hazards and their proper handling and
storage procedures.
• It distinguishes potential ignition sources and the proper control procedures of those
materials.
• The plan describes fire protection equipment and/or systems used to control fire
hazards.
• It identifies persons responsible for maintaining the equipment and systems installed to
prevent or control ignition of fires.
• The FPP identifies persons responsible for the control and accumulation of flammable or
combustible material.
• It describes good housekeeping procedures necessary to insure the control of
accumulated flammable and combustible waste material and residues to avoid a fire
emergency.
• The plan provides training to employees with regard to fire hazards to which they may
be exposed.
1. The LEAST important reason to have a Fire Prevention Plan (FPP) is to _____.
a. comply with OSHA b. prevent loss of property by fire c. eliminate the causes of fire d. prevent loss of life
Course 629
Copyright © 2018 Geigle Safety Group, Inc. Page 23 of 31
FPP Responsibilities
Fire safety is everyone's responsibility. All employees should know how to prevent and respond
to fires, and are responsible for adhering to company policy regarding fire emergencies.
Management
Management determines fire prevention and protection policies. They should do the following:
• Managers should provide adequate hazard controls to provide a safe workplace.
• Managers should also provide adequate resources and training to employees to
encourage fire prevention and the safest possible response in the event of a fire
emergency.
Plan Administrator
This person maintains all records pertaining to the plan. The Plan Administrator should also:
• Develop and administer the fire prevention training program.
• Ensure that fire control equipment and systems are appropriate and properly
maintained.
• Control fuel source hazards in the workplace.
• Conduct fire risk surveys and make recommendations for improvement.
Supervisors
Supervisors ensure that employees receive appropriate fire safety training.
• Supervisors should notify the plan administrator when changes in operation increase
the risk of fire.
• They are also responsible for enforcing fire prevention and protection policies.
Employees
All employees should complete all required training before working without supervision. It's
important that employees also:
Course 629
Copyright © 2018 Geigle Safety Group, Inc. Page 24 of 31
• Conduct operations safely to limit the risk of fire.
• Report potential fire hazards to their supervisors.
• Follow fire emergency procedures.
2. Who is responsible for ensuring employees receive proper training in the Fire
Prevention Plan (FPP)?
a. Plan administrators b. Supervisors c. Safety committees d. Safety staff
Written Plan Components
A fire prevention plan must be in writing, be kept in the workplace, and be made available to
employees for review. However, according to OSHA, if you have 10 or fewer employees you
may communicate the plan orally to employees.
At a minimum, your fire prevention plan must include:
• A list of all major fire hazards, proper handling and storage procedures for hazardous
materials, potential ignition sources and their control, and the type of fire protection
equipment necessary to control each major hazard;
• Procedures to control accumulations of flammable and combustible waste materials;
• Procedures for regular maintenance of safeguards installed on heat-producing
equipment to prevent the accidental ignition of combustible materials;
• The name or job title of employees responsible for maintaining equipment to prevent or
control sources of ignition or fires; and
• The name or job title of employees responsible for the control of fuel source hazards.
An employer must inform employees upon initial assignment to a job of the fire hazards to
which they are exposed. An employer must also review with each employee those parts of the
fire prevention plan necessary for self-protection.
Course 629
Copyright © 2018 Geigle Safety Group, Inc. Page 25 of 31
3. At a minimum the Fire Prevention Plan (FPP) must contain _____.
a. potential sources of overexposure b. procedures to control all substances c. a list of all major fire hazards d. corrective maintenance procedures
FPP Best Practices
To limit the risk of fires, good housekeeping is critical. All employees should take the following
precautions:
• Minimize the storage of combustible materials.
• Make sure that doors, hallways, stairs, and other exit routes are kept free of
obstructions.
• Dispose of combustible waste in covered, airtight, metal containers.
• Use and store flammable materials in well-ventilated areas away from ignition sources.
• Use only nonflammable cleaning products.
• Keep incompatible (i.e., chemically reactive) substances away from each other.
• Perform "hot work" (i.e., welding or working with an open flame or other ignition
sources) in controlled and well-ventilated areas.
• Keep equipment in good working order (i.e., inspect electrical wiring and appliances
regularly and keep motors and machine tools free of dust and grease.
• Ensure that heating units are safeguarded.
• Report all gas leaks immediately. A responsible person shall ensure that all gas leaks are
repaired immediately upon notification.
• Repair and clean up flammable liquid leaks immediately.
• Keep work areas free of dust, lint, sawdust, scraps, and similar material.
Course 629
Copyright © 2018 Geigle Safety Group, Inc. Page 26 of 31
• Do not rely on extension cords if wiring improvements are needed, and take care not to
overload circuits with multiple pieces of equipment.
• Ensure that required hot work permits are obtained.
• Turn off electrical equipment when not in use.
4. Which of the following is an important best practice within the Fire Prevention Plan
(FPP)?
a. Keep exit routes free of obstructions b. Ensure hot work is performed only on live pipelines c. Keep combustible waste in open, non-flammable, synthetic barrels d. Ensure flammable liquids are cleaned up as soon as practical
Hazards that Cause Fires
Electrical Hazards
Electrical system failures and the misuse of electrical equipment are leading causes of
workplace fires. Fires can result from loose ground connections, wiring with frayed insulation,
or overloaded fuses, circuits, motors, or outlets.
Portable Heaters
All portable heaters should be approved by the plan administrator. Portable electric heaters
should have tip-over protection that automatically shuts off the unit when it is tipped over.
Office Fires Hazards
Fire risks are not limited to industrial facilities. Fires in offices have become more likely because
of the increased use of electrical equipment, such as computers.
Welding, Cutting, and Open Flame Work
Welding and cutting and working with open flames are obvious fire hazards in the workplace,
and in some cases fire watches need to be positioned close by, and barriers may need to be
placed between welding and materials that might catch fire.
Flammable and Combustible Materials
If your workplace contains flammable and combustible materials, the plan administrator should
regularly evaluate the presence of those materials.
Course 629
Copyright © 2018 Geigle Safety Group, Inc. Page 27 of 31
• Class A Combustibles: These include common combustible materials (wood, paper,
cloth, rubber, and plastics) that can act as fuel and are found in non-specialized areas
such as offices.
• Class B Combustibles: These include flammable and combustible liquids (oils, greases,
tars, oil-based paints, and lacquers), flammable gases, and flammable aerosols.
Smoking in the Workplace
In an effective FPP, smoking is prohibited in all company buildings. Certain outdoor areas may
also be designated as no smoking areas. The areas in which smoking is prohibited outdoors
should be identified by NO SMOKING signs.
5. Under the Fire Prevention Plan (FPP), portable heaters should _____.
a. be approved by the user b. rely on proper manual shut-off switches c. have Z359-approved components d. have tip-over protection
Fire Extinguishing Systems
A fire extinguishing system is an engineered set of components that work together to quickly
detect a fire, alert occupants, and extinguish the fire before extensive damage can occur. All
system components must be:
• Designed and approved for use on the specific fire hazards they are expected to control
or extinguish.
• Protected against corrosion or either made or coated with a non-corrosive material if it
may be exposed to a corrosive environment.
• Designed for the climate and temperature extremes to which they will be exposed.
Fixed Extinguishing Systems
Fixed fire extinguishing/suppression systems are commonly used to protect areas containing
valuable or critical equipment such as data processing rooms, telecommunication switches, and
process control rooms. Their main function is to quickly extinguish a developing fire and alert
occupants before extensive damage occurs by filling the protected area with a gas or chemical
extinguishing agent.
Course 629
Copyright © 2018 Geigle Safety Group, Inc. Page 28 of 31
Portable Extinguishing Systems
Workplace fires and explosions kill hundreds and injure thousands of workers each year. One
way to limit the amount of damage due to such fires is to make portable fire extinguishers an
important part of your FPP. When used properly, fire extinguishers can save lives and property
by putting out a small fire or controlling a fire until additional help arrives.
For more information on fire extinguishing systems and using portable fire extinguishers, see
OSHAcademy course 718 Fire Prevention Plans.
6. Which type of fire extinguishing system is commonly used to protect areas containing
valuable or critical equipment?
a. Portable extinguishing system b. Fixed extinguishing system c. OSHA-approved extinguishing system d. Regulated extinguishing system
How to Use a Fire Extinguisher
Even though extinguishers come in a number of shapes and sizes, they all operate in a similar
manner. Here's an easy acronym for fire extinguisher use:
P A S S -- Pull, Aim, Squeeze, Sweep
Pull the pin at the top of the extinguisher that keeps the handle from being accidentally
pressed.
Aim the nozzle toward the base of the fire.
Squeeze the handle to discharge the extinguisher. Position yourself approximately 8 feet away
from the fire. If you release the handle, the discharge will stop.
Sweep the nozzle back and forth at the base of the fire. After the fire appears to be out, watch
it carefully since it may re-ignite!
Make sure all employees who are expected to use fire extinguishers if a controllable fire occurs
are properly trained with hands-on practice. There's no OSHA requirement to actually
extinguish a fire or discharge a fire extinguisher during training. However, each employee
should handle the fire extinguisher and demonstrate they can perform the PASS steps.
Course 629
Copyright © 2018 Geigle Safety Group, Inc. Page 29 of 31
7. When using a fire extinguisher, be sure use the _____ method.
a. On, Sweep, Hold, Aim b. Pull, Aim, Squeeze, Sweep c. Behind, Load, Aim, Sweep, Train d. Hold, Operate, Squeeze, Empty
FPP Training Requirements
Employers should train workers about fire hazards in the workplace and about what to do in a
fire emergency.
Management Training Responsibilities: Unless a specific manager is designated, all managers
should be responsible for coordinating with the Plan Administrator for training all employees
covered under the FPP.
• All managers should be educated to understand their FPP responsibilities including
inspection and drill procedures.
• Managers should also make sure all employees who might be expected to use portable
fire extinguishers are properly trained.
• Supervisors should train employees about the fire hazards associated with the specific
materials and processes to which they are exposed, and maintain written
documentation of the training.
Many of the topics taught in the FPP training may be presented in the classroom. If employees
are expected to use portable fire extinguishers, they must participate in "hands-on" exercises
that help them understand the procedures. Hands-on training also gives employees an
opportunity to demonstrate to trainers that they have the skills required to use fire
extinguishers.
At a minimum, FPP Training should include all of the following topics:
• review OSHA requirements contained in 29 CFR 1910.38, Emergency Action Plans,
• review OSHA requirements contained in 29 CFR 1910.39, Fire Prevention Plans,
• person(s) responsible for Control of Fuel Source Hazards,
• the location of the company FPP and how it can be accessed,
Course 629
Copyright © 2018 Geigle Safety Group, Inc. Page 30 of 31
• good fire-prevention housekeeping practices and equipment maintenance,
• alarm systems and evacuation routes,
• proper response and notification in the event of a fire,
• the use of portable fire extinguishers, and
• recognition of potential fire hazards.
8. In the Fire Prevention Plan (FPP), when must employees be given hands-on training?
a. When given responsibility to inspect equipment b. When given supervisory responsibilities c. When acting as fire wardens d. When responsible for operating fire extinguishers
Course 629
Copyright © 2018 Geigle Safety Group, Inc. Page 31 of 31
Additional Resources
1. How to Plan for Workplace Emergencies and Evacuations, OSHA
2. Emergency Response Resources
3. NFPA 1600, Standard on Disaster/Emergency Management and Business Continuity
Programs
4. Evacuation Plans and Procedures eTool
5. Evacuation Plans and Procedures eTool
6. Expect the Unexpected, OR-OSHA
7. Emergency Management Guide for Business & Industry
8. Napo's Films, Via Storia