Pneumatic support leg P-62M-800 / P-62L-0 is used to increase performance and improve the
comfort of working with a WUP-22 drilling machine. The support is intended to support the drilling
machine during operation and to exert uniform pressure on the drill. The articulated connection
of the pneumatic support to the WUP-22 drilling machine makes it possible to drill lateral and
inclined holes. The support is equipped with a regulation valve which makes it possible to smoothly
adjust the pressure force and the slide out speed, providing a firm working grip at the same time.
The support is equipped with a quick release valve for reasons of work safety. The purpose of this
valve is to withdraw the mining device immediately, interrupting the drill pressure.
PNEUMATIC SUPPORT LEG
P-62M-800 / P-62L-0
Pl 40-859Katowice, 6TokarskaStreet, phone+48 /32/6040900, fax+48 /32/6040901, www.moj.com.pl, e-mail:[email protected]
MOJ Plc.
Operating factor
mm
MPaUpstream air pressure
880 1300
0,4÷0,6 0,4÷0,6
Compressed air
Force of pressure at 0,4MPa kN 12,8 12,8
1347 1750
20,5 24,5
Stroke
Total length
Weight
Parameters UnitTYPE
P-62M-800TYPE
P-62L-0
mm
kg
TECHNICAL PARAMETERS OF PNEUMATIC SUPORT
The WUP-22 pneumatic percussive drilling machine is designed for drilling blast holes in medium
hard coal and rocks at air pressure of 0,4 MPa. Bore dust removal can be affected by flushing
or scavening. To increase speed of penetration in horizontal or inclined drilling WUP-22 is adopted
to work with an airleg of P-62M. The purpose of the airleg is supporting the drill during operation
providing uniform pressure and relieving arduousness of men work. Pneumatic drilling machines
WUP-22 require lubrication by compressed air from e.g. a duct lubricator. For WUP-22 we may apply
the tools for hammer drilling: (monolithic) or rods and bits.
PNEUMATIC PERCUSSIVE DRILLING MACHINE
WUP-22
Pl 40-859Katowice, 6TokarskaStreet, phone+48 /32/6040900, fax+48 /32/6040901, www.moj.com.pl, e-mail:[email protected]
MOJ Plc.
ATEX I M2
TECHNICAL PARAMETERS OF WUP-22 DRILLER
Air consumption* m3/min
min-1
min-1Drill revolutions*
1950
200
3,2
Feeding hose diameter Ø25mm
Flushing pipe inner diameter Ø12,5mm
Drill retainer size 22,2(7/8”)x108 or 25,5(1”)x108mm
Energy of blow* J 28
22
Number of strokes*
Weight (without drill bit) kg
* The values obtained of 0,4 MPa compressed air pressure.
Power pressure 0,3 ÷ 0,4 MPa.
Pneumatic hand rotary drilling machine PWR-5U is designed for boring holes up to 62 mm in diameter. Can be
used in the construction industry and tunnels drilling. Its high power permits drilling of blast-holes in salt beds,
ore-body and other soft and mean-hard rocks. The drilling machine is supplied with compressed air via lubricator.
Tools applied for drilling: spiral drilling rod or rhombus spiral drilling rod as well as drill bit. Drill can not be usedin
underground mines.
PNEUMATIC HAND ROTARY DRILLING MACHINE
PWR-5U
Pneumatic hand rotary drilling machine PWR-8T (with noise suppresser) is designed for drilling holes of diameter
up to 43 mm in soft and semi-hard rock. It is successfully used for drilling holes in the salt beds. The drilling
machine is supplied with compressed air via lubricator. Tools applied for drilling: spiral drilling rod or rhombus
spiral drilling rod as well as drill bit. Drill can not be used in underground mines.
PNEUMATIC HAND ROTARY DRILLING MACHINE
PWR-8T
Pl 40-859Katowice, 6TokarskaStreet, phone+48 /32/6040900, fax+48 /32/6040901, www.moj.com.pl, e-mail:[email protected]
MOJ Plc.
Number of drill revolution min-1n
NmMo
kWNRated power
42
2,2
500
Maximal upstream pressure 0,5MPapmax
Air consumption 2,7m3/minQ
Inner diameter of hose 16mmØ
Maximal tool diameter 62mmØ
Upstream pressure MPap 0,4
14
Rated torque
Weight kg
Number of drill revolution min-1n
NmMo
kWNRated power
19,5
1,6
800
Maximal upstream pressure 0,5MPapmax
Air consumption 2,4m3/minQ
Inner diameter of hose 16mmØ
Maximal tool diameter 43mmØ
Upstream pressure MPap 0,4
9,5
Rated torque
Weight kg
TECHNICAL PARAMETERS OF PWR-5U DRILLER
TECHNICAL PARAMETERS OFPWR-8T DRILLER
Pl 40-859Katowice, 6TokarskaStreet, phone+48 /32/6040900, fax+48 /32/6040901, www.moj.com.pl, e-mail:[email protected]
MOJ Plc.
TECHNICAL PARAMETERS OF PZW-1 KIT
ATEX I M2
Pneumatic Drill Kit PDK-1 is used for drilling holes in semi-hard and hard rocks at different angles, with the air
pressure 0.4 ÷ 0.6 MPa. Pneumatic drill kit PDK-1 allows you to remove cuttings from the hole with water
or compressed air. Included with the device is upgraded WUP-22 drill, which is mounted on the pneumatic
prop. Prop is used to support drilling and exert steady pressure on the drill bit during drilling, thereby reducing the
effort of the employee.
PNEUMATIC DRILL KIT
PZW-1
Driller weight (without drill bit)
Length ( without drill bit)
Impact energy
Drill rotation speed (at 0,4 MPa pressure)
Stroke frequency (at 0,4 MPa pressure)
Air consumption (at 0,4 MPa pressure)
Compressed air pressure max. (high timing gear)
Internal diameter of the compressed air hose
Internal diameter of water hose
Dimension of drill grip
Prop length
Useful change of the prop in range
Compressed air pressure max. (low timing gear)
Kit weight PZW-1
ca. 635
ca. 40
0,6
200
ca. 24
3,2
Ø 25
22,2(7/8”)x108 or 25,4(1”)x108
0,4
1950
Ø 12,5
28
kg
J
MPa
m3/min
mm
MPa
1/min
mm
kg
mm
mm
mm according to customer orders
mm 800 ÷ 1300
rpm
Hydraulic Mining Drill WGH - 4 is designed mainly for manual rotary drilling of openings in rocks of medium hardness with use of tools
consisting of spiral drilling rod ended by drilling bit. It is characterized by low weight using two-handed grip.
Maximum drilling diameter Ø48 mm.
Drill WGH-4 can be use directly while performing work in underground mining and other places
where methane hazard categories are "b" and "c" and B grade coal dust explosion hazard.
Drills can be adapted to the needs of the customer in mass, momentum, pressure, power, and used medium.
Drill without gear.
Weight ratio to rotational torque 0.04.
HYDRAULIC MINING DRILL
WGH-4
Pl 40-859Katowice, 6TokarskaStreet, phone+48 /32/6040900, fax+48 /32/6040901, www.moj.com.pl, e-mail:[email protected]
MOJ Plc.
TECHNICAL PARAMETERS OF WGH-4 DRILLER
Maximal rotational speed rpmn max
NmMo
barPWork pressure
72
220÷300
957
Maximal work temperature (front body) 75,3°C
Type of medium usedHydraulic oil HLP 48 or water-oil emulsion
motor absorption l/minQ 25 przy 500 rpm
5
Maximal rotary torque
Driller weight kg
Hydraulic Mining Drill WGH-6u is designed mainly for manual rotary drilling of openings in hard rocks and overgrowth rock of varying hardness with use
of tools consisting of spiral drilling rod ended by appropriate tool . Drill has a mechanical stroke-assistant driller supporting the work, so that it becomes
less cumbersome.
Maximum drilling diameter Ø48 mm.
Drill WGH-6u can be use directly while performing work in underground mining and other places where methane hazard categories are
"b" and "c" and B grade coal dust explosion hazard.
Drills can be adapted to the needs of the customer in mass, momentum, pressure, power, and used medium.
HYDRAULIC MINING DRILL
WGH-6u
Pl 40-859Katowice, 6TokarskaStreet, phone+48 /32/6040900, fax+48 /32/6040901, www.moj.com.pl, e-mail:[email protected]
MOJ Plc.
TECHNICAL PARAMETERS OF WGH-6u DRILLER
Maximal rotational speed rpmn max
NmMo
barPWork pressure
150
220÷300
820
Maximal work temperature (front body) 90°C
Type of medium usedHydraulic oil HLP 48 or water-oil emulsion
motor absorption cm3/rpmQ 50
8
Maximal rotary torque
Driller weight kg
Drill without gear.
Weight ratio to rotational torque 0.053.
Mining Pneumatic hand rotary drilling machine PWR II is designed for boring blast-holes in coal, salt beds, ore-body and other soft and
mean-hard rocks. The main advantage of drill PWR II is its use directly while performing work in underground mining where methane hazard
categories are "a", "b" and "c" and A and B grade coal dust explosion hazard. The drilling machine is supplied with compressed air via
lubricator. Tools applied for drilling: spiral drilling rod or rhombus spiral drilling rod as well as drill bit.
Maximum drilling diameter is Ø62 mm.
Drill Weight - 19 kg.
PNEUMATIC HAND ROTARY DRILLING MACHINE
PWR II
Pl 40-859Katowice, 6TokarskaStreet, phone+48 /32/6040900, fax+48 /32/6040901, www.moj.com.pl, e-mail:[email protected]
MOJ Plc.
ATEX I M2
TECHNICAL PARAMETERS OF PWR II DRILLER
Number of drill revolutions min-1n
NmMo
kWNRated power
27
1,6
580
Maximal Upstream air pressure 0,5MPapmax
Requisition of compressed air 2,7m3/minQ
Inner diameter of hose 16mm∅
Maximum tool diameter 62mm∅
Upstream air pressure MPap 0,4
19
Rotary torque
Weight kg
The S-type line oil lubricator is intended for lubricating devices propelled by compressed air, such as drilling machines, pumps and supports with oil
mist. Can be used in underground mines in hazard zones with the danger of methane and f coal dust explosion risk. The oil in the lubricator
is atomised in the form of oil mist and reaches, together with the compressed air, all the surfaces that rub against each other during operation,
preventing scuffing. Lubricating using an oil mist is one of the best methods of lubrication, helping lengthen the life of devices propelled by
compressed air. The lubricator is placed on the tube supplying compressed air to the lubricated devices at a distance that does not exceed 5 m.
The lubricator does not require additional maintenance, apart from filling with oil.
LINE OIL LUBRICATOR
S-3 / S-4
Pl 40-859Katowice, 6TokarskaStreet, phone+48 /32/6040900, fax+48 /32/6040901, www.moj.com.pl, e-mail:[email protected]
MOJ Plc.
TECHNICAL PARAMETERS OF LINE OIL LUBRICATOR
Oil consumption in temperature 15÷20°C ml/h
MPa
lCapacity
0,5 ÷ 0,6
1
ca. 100
Inner diameter of hose mm 25
ca. 2,5
Maximal pressure
Weight (without oil) kg
Unit S-3Parameters
Ambient temperature OC 0 ÷ 40
0,5 ÷ 0,6
1
ca. 100
25
ca. 4,0
S-4 (steel)
0 ÷ 40
1,551,551,55kWRated power 1,55 1,55
Power supply
ER-6...U
0÷ 40
1,1
127 ; 220
50
0,86
8,1 ; 4,7
4
0,72
F
610
17,5
S2÷30min
IP-54
Ex d I
19,2
ER-62/4
0÷ 40
1,1
220
50
0,86
4,7
4
0,72
F
400
26,6
S2÷30min
IP-54
Ex d I
16,5
The ER-6 electric hand drilling machine is designed for drilling holes in solid coal and mean-hard rock using helical drill rod with drill bit in diameter
of 43 mm. The driller has flameproof construction and can be used in underground mines in a, b or c hazard zones with the danger of methane
explosion and at level A and B of coal dust explosion risk. Drill is manufactured in the following varieties: ER-6 ER-6 / 4, Voltage: ER-61
(3x127V) ER-62 (3x220V) and ER-61 / 4 (3x127V), ER-62 / 4 (3x220V), there is also a performance of the ER-6 ...U with supporting drilling
hammer head.
ELECTRIC HAND DRILLING MACHINE
ER-6 127 V, 220 V
Pl 40-859Katowice, 6TokarskaStreet, phone+48 /32/6040900, fax+48 /32/6040901, www.moj.com.pl, e-mail:[email protected]
MOJ Plc.
TECHNICAL PARAMETERS OF ER-6 DRILLER
V
A
-
-
-
rpm
Nm
-
-
-
kg
Unit
0÷ 40°C
ER-61Parameters
Motor rating
Frequency
Cos ϕRated current
Times the starting current
Efficiency
Insulation class
Rotational speed
The torque on the drill
Work
Degree of cover protection
Marking flameproof
Weight without cable drill
Ambient temperature
kW
Hz
-
1,1
127
50
0,86
8,1
4
0,72
F
610
17,5
IP-54
Ex d I
15,5
0÷ 40
ER-62
1,1
220
50
0,86
4,7
4
0,72
F
610
17,5
S2÷30minS2÷30min
IP-54
Ex d I
15,5
0÷ 40
6100--Ud/minThe frequency of stroke - -
ER-61/4
1,1
127
50
0,86
8,1
4
0,72
F
400
26,6
S2÷30min
IP-54
Ex d I
16,5
Allowed deviation values not exceeding + / - 5% of the nominal value.
IM2c Exdl
Length of
the drop
[mm]
Height of the
extended prop
[mm]
Height of the
withdrawn prop
[mm]
Prop
weight
[kg]
Strength
of support
[kN]
450 450
500 500
560 560
630 630
710 710
800 800
900 900
28,3
29,2
30,3
31,6
32,9
34,6
36,5
380
400
440
470
500
560
630
1000 1000
1120 1120
1250 1250
1400 1400
1600 1600
1800 1800
2000 2000
38,4
40,5
43,0
45,7
49,4
53,1
56,7
670
710
800
900
1000
1120
1250
2240
Item
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
2240 61,21400
2500 2500
2800 2800
3150 3150
3550 3550
4000 4000
4250 4250
66,0
71,5
78,0
85,2
93,6
100,1
1600
1800
2000
2240
2500
2750
4500 4500 107,0 200
250
400
320
3000
VALENT FRICTION PROP
SN-400-MOJ
Pl 40-859Katowice, 6TokarskaStreet, phone+48 /32/6040900, fax+48 /32/6040901, www.moj.com.pl, e-mail:[email protected]
MOJ Plc.
TECHNICAL PARAMETERS OF SN-400-MOJ FRICTION PROP
The VALENT SN-400 -MOJ friction props are individual elements of lining whose is to prop the roof in mining excavations:
longwall and splitting excavations, and to reinforce the lining of gallery excavations. Props may form an independent lining or be
used as elements reinforcing another type of lining.
The series of types of the VALENT SN-400 -MOJ friction props include twenty two principal sizes ranging from 450mm
to 4500mm when extended out.
The VALENT SN-400 -MOJ prop is certified and marked by safety sign.
Pneumatic impact root bolting machine PKU-1 is designed for drilling shot and anchoring holes in the
roof of medium-hard and hard rocks in excavations of height over 2600 mm at the pneumatic support
stroke of 1300 mm as well as for tamping of anchor bolts. Upon the customer’s request we may
manufacture an anchoring machine with different cylinder stroke. The roof bolting machine PKU-1 has
a possibility of adjusting the position of control valve depending on the excavation height. The adjustment
is made by an operator of the anchoring machine at the workstation. Such a solution considerably
reduces the noxiousness of work with the equipment.
Maximum drilling diameter is 45 mm.
PNEUMATIC ROOF BOLTING MACHINE
PKU-1
Pl 40-859Katowice, 6TokarskaStreet, phone+48 /32/6040900, fax+48 /32/6040901, www.moj.com.pl, e-mail:[email protected]
MOJ Plc.
ATEX I M2
TECHNICAL PARAMETERS OF PKU-1 ROOF BOLTING MACHINE
* The values obtained of 0,4 MPa compressed air pressure.
It is possible to make pneumatic impact root bolting machine with a different length as described above
and the corresponding jump usefull.
Height with height with stretched
(2)
prop (effective travel) (1)
Length without drilling rod (1)
Pessing force*
Minimum supply pressure
Maximum supply pressure
(2)
Tool speed*
Impact energy*
Air consumption
Internal diameter of the compressed air hose
Internal diameter of the water hose
Dimensions of drill shank
Stroke frequency*
Mass
17402240
3540
45
24,5
0,4
2540
200
3,2
12,5
22,2(7/8”)x108 or 25,5(1”)x108
1950
0,6
25
12,8
mm
kg
kN
J
rpm
m3/min
mm
mm
1/min
MPa
mm
mm
mm
mm
MPa
The PKU-3 compressed-air impact roof bolting machine is a multipurpose machine intended for
drilling the blast holes in the roof and for drilling the bolt holes, for tamping and tightening the bolts
in medium and hard rocks. Due to placing the drill at the side of the ram, a very compact design
combined with a relatively high value of the active stroke has been obtained. The PKU-3 roof
bolting machine has been designed especially for low underground workings and for faces where
realization of the roof bolting is required directly after blasting, because it enables drilling to
be effected from heaps of the gotten material. The minimum height of the working is determined
by the length of the initial drill and amounts to 1400 mm.
PNEUMATIC ROOF BOLTING MACHINE
PKU-3
Pl 40-859Katowice, 6TokarskaStreet, phone+48 /32/6040900, fax+48 /32/6040901, www.moj.com.pl, e-mail:[email protected]
MOJ Plc.
ATEX I M2
TECHNICAL PARAMETERS OF PKU-3 ROOF BOLTING MACHINE
* The values obtained of 0,4 MPa compressed air pressure.
Length
Height with maximal stretched prop
Impact energy*
Pessing force*
Cylinder stroke
Air consumption *
Stroke frequency*
Internal diameter of the compressed air hose
Internal diameter of the water hose
Dimensions of drill shank
Drill bit rotation speed*
Mass
1740
42
1950
12,8
940
3,2
25
22,2(7/8”)x108 or 25,5(1”)x108
200
750
12,5
24,5
kg
J
1/min
m3/min
mm
1/min
mm
mm
mm
mm
mm
kN
Hydraulic roof bolting machine KHTP–1,5A is designed for rotary drilling with water flushing
of holes in roofs of mining excavations of an angular and rectangular cross-section as well
as mounting small diameter glued anchors therein. The roof bolting machine can be applied for
anchoring dog headings and chamber excavations in rock of mean hardness and of compressive
strength up to 60 MPa. The roof bolting machine should be fed with hydraulic oil HLP – 68 by
means of the power unit AG-63/16Z. Supply can be effected by other power unit meeting the
requirements given in the technical specification of the anchoring machine.
HYDRAULIC ROOF BOLTING MACHINE
KHTP-1,5A
Pl 40-859Katowice, 6TokarskaStreet, phone+48 /32/6040900, fax+48 /32/6040901, www.moj.com.pl, e-mail:[email protected]
MOJ Plc.
ATEX I M2
TECHNICAL PARAMETERS OF KHTP-1,5A ROOF BOLTING MACHINE
* Values obtained at a pressure of 0.4 MPa compressed air.
Rated torque
Drill holding down force
Maximal drill rotational speed*
Maximal Instantaneous pressure*
Maximal working pressure
The maximum diameter of the drilling anchor
Rate of travel
Maximum water pressure
Drill stroke
Hydraulic roof bolting machine KHTP 1,5A mass
4,0 ÷ 10
80
0 ÷ 2
17,5
130
Ø 43 (recommended Ø 28)
0,8
1500
14,5
700
kg
rpm
m/min
MPa
mm
MPa
kN
Nm
MPa
Hydraulic aggregate set AG 63/16Z is designed for supplying of equipment in underground excavations and may be used in underground mines
in a, b or c hazard zones with the danger of methane explosion and at level A and B of coal dust explosion risk. In particular it is designed
for supplying such equipment as hydraulic roof bolting machines,
hydraulic drilling machines and other equipment with hydraulic drive.
The version with a double-section pump (AG-16/63/40Z) allows for
simultaneous operation of two different pieces of equipment
(roof bolting machine and hydraulic drilling machine).
It is possible to extend the application of aggregate
to cooperation with other devices with hydraulic drive.
HYDRAULIC AGGREGATE SET
AG 63/16Z
Pl 40-859Katowice, 6TokarskaStreet, phone+48 /32/6040900, fax+48 /32/6040901, www.moj.com.pl, e-mail:[email protected]
MOJ Plc.
ATEX I M2
TECHNICAL PARAMETERS OF AG 63/16Z AGGREGATE
Nominal diameter of terminal
Motor power
Supply Engine voltage
Nominal pump capacity
Max oil pressure
Nominal diameter of runoff
Type of oil
Diameter of the cooling water connection
Overall dimensions
Aggregate weight without oil
Ambient temperature
Relative humidity 93% at temperature 40OC ± 2OC
Oil collection volume
Technical parameters
15 or 22 22
AG-63/16/40Z (for Dual-Pump)
HL-48 or L-HL 68
63 ÷ 100 63/40
20 2 X 20
25
¾”
ca. 550
10 ÷ 40
< 200
16 ÷ 21 14,5
ca. 750 x 800 x 1800
500 ÷ 100
Unit
V
mm
mm
kgOC
l
MPa
kW
mm
l/min
AG-63/16Z
OP-80C pump is designed for pumping highly polluted water at a temperature till
40°C. It is a portable pump powered by compressed air directly immersed in liquid.
In the case of total immersion pump outlet air pipe should be extended above the
liquid mirror. In the mining is used to dewater the excavation, sewage, at work
related to the sinking.
Pump Weight: about 100 kg.
DRAINAGE PUMP
OP-80C
Pl 40-859Katowice, 6TokarskaStreet, phone+48 /32/6040900, fax+48 /32/6040901, www.moj.com.pl, e-mail:[email protected]
MOJ Plc.
TECHNICAL PARAMETERS OF OP-80C PUMP
*The pump can be equipped with various types of terminals for compressed air connection 1 "diameter.
Mass
Air consumption
Lifting height
Efficiency
The efficiency of isothermal
Connection diameter structurally
for the liquid - Pitch for bolts
Diameter Compressed air connection*
The internal diameter of discharge port
Technical parameters of pump0,4 0,5
Air pressure MPa
0,21η i 0,24
mwater column 33 40
≈100 ≈100
85
150
25,4
l/min 300 300
2,9
Designation
Vp Nm3/min 2,3
mm 85
mm 150
mm 25,4
Q
kg
H
Unit
IM1c
Torque spanner KD-3/KD-4 is designed to turn tight bolts of lining on required moment. Wanted magnitude of moment is obtained through adequate
regulation of spring tension handwheel located in end part of the spanner. Required magnitude of moments is read off on the scale located in gripped
part of the spanner. The scale has measurement range of 300-600 Nm. When checking screw home moment, exceed of moment is signaled by loud
click of the pawl, located in central part of the spanner. The spanner is equipped with torque system to eliminate necessity of removing spanners cap
from screw head.
TORQUE SPANNER
KD-3, KD-4
Hand spanner bended KRW-1 and hand spanner straight KRP-1 are two-way action spanners with ratchet mechanism. They are served to tum
off back off screw joints with the help of exchangeable thimbles: normal L = 110 mm and a short L = 75 mm. Thimbles can be ordered
independently of a key or a set with him.
HAND SPANNER BENDED / HAND SPANNER STRAIGHT
KRW-1, KRP-1
Pl 40-859Katowice, 6TokarskaStreet, phone+48 /32/6040900, fax+48 /32/6040901, www.moj.com.pl, e-mail:[email protected]
MOJ Plc.
TECHNICAL PARAMETERS OF KD-3, KD-4 SPANNER
TECHNICAL PARAMETERS OF KRW-1, KRP-1 SPANNER
Size of head for thimbles kw. 25,4mm(1cal) kw. 25,4mm(1cal)
6,5 kg
300 ÷ 500 NmMagnitude range of moment
6,5 kg
400 ÷ 600 Nm
KD-4
Weight (with torque and without thimb)
Type KD-3
Length 921 mm 921 mm
Length 420 mm
Size of joint for thimbles kw. 25,4 mm(1cal)
25 Nm
250 NmMoment of screwin extending rod
Moment of screwing
Weight (without thimble) 1,5 kg
Standard thimbles: L = 110 mm
S24
D
(M16)
43
27
(M18)
43
30
(M20)
43
32
(M22)
48
36
(M24)
53
41
(M27)
58
46
(M30)
63
50
(M33)
68
55
(M36)
74
Short thimbles: L = 75 mm
S16
D
(M10)
43
20
(M12)
43
24
(M16)
43
30
(M20)
43
32
(M22)
48
36
(M24)
53
41
(M27)
48
46
(M30)
63
Department of Construction &Technology employs a young, highly educated designers who closely follow the development of world technology
and uses its achievements in construction solutions. Functioning of the department is anchored in the Quality Management System acc.
EN ISO 9001:2008.
Programs used: inventor of engineering 3D, technological Alphacam, Peps, and CAM allows to create a modern optimized structures and their
unusual adaptations of the solutions. We meet the individual needs of our clients in solving their problems of construction & Technology.
The versatility of the office allows to create products for various markets such as mining, energy, cement industry, machine and sugar industry.
Group of technologists implements modern technologies of making products and exercises permanent oversight of the implemented in
production the technological processes.
CONSTRUCTION & TECHNOLOGY DEPARTMENT
MOJ S.A.
Pl 40-859Katowice, 6TokarskaStreet, phone+48 /32/6040900, fax+48 /32/6040901, www.moj.com.pl, e-mail:[email protected]
MOJ Plc.
Company Service is a group of engineering and technical personnel with extensive experience in solving problems related to production, operation
quality and reliability of products manufactured in the Company MOJ SA Katowice.
We provide fast and professional guarantee service and post-guarantee for machinery and equipment.
Support services are performed at the client or in our company, depending on the technical conditions needed for servicing.
At the company headquarters is well equipped laboratory, including the latest coordinate measuring machine produced by "Wenzel" company.
A wide range of devices and diagnostic tools allows you to verify diagnosis of problems, the correctness of the product, determine the reasons
for any incorrectness of the action and rapid correction.
SERVICE
MOJ S.A.
Pl 40-859Katowice, 6TokarskaStreet, phone+48 /32/6040900, fax+48 /32/6040901, www.moj.com.pl, e-mail:[email protected]
MOJ Plc.