Polycom® RealPresence® Group Series Media Centerwith 65 Inch Dual Displays
SETUP SHEET
This supplement describes how to attach 65 inch dual displays on the Polycom® RealPresence® Group SeriesMedia Center. Follow the instructions in Setting Up the Polycom RealPresence Group Series Media Center,1725-08510-00X, and use this supplement to replace the steps to install the displays.
Single 55/65 inch Lower Display Rail, 1354-67626-002
(2) Dual 65 inch Lower Display Rail Extension, 1354-68667-002
Dual 65 inch Center Top Display Rail, 1354-68669-001
(2) Dual 65 inch Upper Display Rail Extension, 1354-68671-001
(4) M10 x 25 Flanged Socket HeadCap Screw1601-67617-002
M8 Wrench1102-68064-001
For more information about the components of the RealPresence Group Series Media Center,refer to the documentation athttp://support.polycom.com/PolycomService/support/us/support/video/group_series/group_packaged_solutions.html.
The Media Center components are heavy. Polycom recommends that two people perform the installation.
Polycom, Inc. and are registered and/or common law marks in the United States and various other countries. No portion hereof may be reproducedor transmitted in any form or by any means, for any purpose other than the recipient’s personal use, without the express written permission of Polycom.
1725-68117-002B
Polycom RealPresence Group Series Media Center Setup Sheet 2
Install the lower display rail by aligning the holes in the display rail with the holes in the vertical supports. Attach with four M10 x 25 flanged socket head cap screws. Do not fully tighten.
Install a lower display rail extension to each side of the lower display rail using two M8 x 20 button head cap screws and two M8 hex nuts per side. Ensure the edge of the rail extension is 3.97 inches from the inner cut edge of the bottom display rail. Tighten using the supplied M8 wrench.
Attach an upper display rail extension to each end of the center top display rail using two M10 x 25 flanged socket head cap screws per extension.
Polycom RealPresence Group Series Media Center Setup Sheet 3
Install the upper display rail assembly by aligning the holes in the display rail with the holes in the vertical supports. Attach with two M10 x 25 flanged socket head cap screws per vertical support. Do not fully tighten.
Attach the rear panel by inserting the two tabs at thebottom of the door into the slots in the base. Thisserves as an alignment tool to ensure the frame isproperly aligned before tightening all bolts. Usingthe L-key, tighten the socket head cap screws atthe bottom of the base, the lower display rail, andthe upper display rail. Remove the rear door.
On the back side, install a handle on both ends of the bottom display rail.
Polycom RealPresence Group Series Media Center Setup Sheet 4
Install the display mount brackets on the display. For the LG display, position the display mounting bracket using the sixth hole from the top with the top mounting hole on the display. The bottom hole on the display is the seventh hole up from the bottom of the bracket.
For the Sampo display, position the third hole down from the top of the display bracket with the third hole down from the top of the display. The bottom hole on the display lines up with the fifth hole up from the bottom of the display bracket.
Install the supplied 1/4-20 x 3.5 inch socket head cap screws at the top of each display bracket. Leave the screws adjusted up before mounting the display to the top rail.
Repeat with the second display.
With the assistance of another person, lift the display and position the display bracket hooks above the edge of the upper horizontal display rail on the Media Center. Carefully lower the display onto the rail, ensuring the hooks are fully engaged with the rail and that the outer most bracket is positioned within the safety tab on the outer rail end (1). Repeat with the second display.
Adjust the leveler screws as needed to help eliminate any gap between the two displays when they are tightly abutted (2).
Polycom RealPresence Group Series Media Center Setup Sheet 5
Center the displays on the Media Center. Insert one M6 x 16 flanged button head screw into each outer display bracket to lock the displays.
Power Rating:Voltage rating: 100-240 VAC, 50/60Hz
Maximum power consumption (configured with GrouSeries 500 codec and EagleEye IV camera under fullload operating conditions): 231.4W with Sampo display165.4W with LG display
Approximate system weight (including displays,codec, camera, and sound system): 715 lbs. with Sampo display689 lbs. with LG display
Regulatory Notices: This equipment is intended for indoor use only. Only use this equipment with the displays supplied by Polycom. Do not use a power cord that is damaged. This could cause fire or electric shock. Contact the manufacturer for a replacement cord, if necessary. Only use a power cord which is appropriately rated and approved relevant to the country of use. This equipment should be used only on even surfaces. When moving or positioning the system, only use the handles located at the bottom of the display rail at the rear of the unit. This equipment has lockable wheels which should be applied while the cart is stationary. When connecting to the mains supply, connect only to an earthed supply outlet which is installed near the equipment and is easily accessible. Keep ventilation openings free from any obstructions. The ambient operating temperature rating of this equipment is 0 - 40ºC and should not be exceeded. Do not immerse the system in any liquid or place any liquids on it. Do not spray liquids directly onto the system when cleaning. Always apply the liquid first to a static-free cloth. For further information concerning the individual components of this equipment, please refer to the respective product literature. For support or service, please contact your Polycom® distributor or go to Polycom Support at www.polycom.com/support.
