Accessories

12H R KI 1

System connections

PORTABLE CD STEREO SYSTEM

Turn on your system

The first time the unit is plugged in with AC power, the unit will enter the demonstration mode.

1 Press the ON/STAND-BY button to turn the power on.

Placing the unit

GX-M10H(OR)GX-M10H(RD)

This quick Start Guide will help you to correctly install andoperate your system.Illustration printed in this quick guide are for the model GX-M10H(OR)

MODEL

Remote control battery installation

TV

Video Cable(not supplied)

1

(RRMCGA292AWSA)

(UM/SUM-3, R6, HP-7 or similar) x 1

PORTABLE MUSIC BOOMBOX GX-M10

REMOTE SENSOR

TIMER

1 Open the battery cover.

2 Insert the batteries as shown.

3 Close the cover.

Use an “AA” size batteries (UM/SUM-3, R6, HP-7 or similar).

Position 1- On the shelf / table.

Position 2- On the floor / ground.

To get the best display viewing angle, place the unit as below.

TROP ABLE M ISU OB C MO B G XO X-M10

Foot cushion 1 and 2touching the surface.

OP RTABLE ISUM B C OOMBOX GX-M10

Foot cushion 2 and 3 touching the surface.

To DC IN 12 V socket

Car adaptor (not supplied)Socket: DC 12 V 4.5 A

To AC INPUT socket

Wall socketAC 110 - 240 V ~ 50/60 Hz

Barcodesofthttp://www.barcodesoft.com

Barcode Symbology: Code 93; Font Facename: Code93MData To Encode: TINSEA414AWZZ

Point Size 8 : *TINSEA414AWZZTJ*|

Point Size 10 : *TINSEA414AWZZTJ*|Point Size 12 :

*TINSEA414AWZZTJ*|Point Size 14 :

*TINSEA414AWZZTJ*|

TINSEA414AWZZ

Dock connector

iPhone (bottom)

Connecting a guitar / microphone Listening to a CD or MP3/WMA disc

Listening to the iPod, iPhone and iPad

3/8/07, 3:46 PM

Note:USB terminal does not support VIDEO out.

iPod, iPhone and iPad connection (USB only)

1 Insert the connector to the iPod, iPhone or iPad.

2 Place the iPad to the stand for iPad.

3 Connect the iPod, iPhone or iPad to the unit via USBconnector.

iPad

Connector

iPad

Stand for iPad

Caution:Unplug all accessories from the iPod or iPhone beforeinserting it into the dock.Note:Do not use the docking station to connect your iPad.

iPod and iPhone connection (Dock only)

1 Open the iPod door by pushing theiPod door open knob to the area marked ‘ ’.Cautions:

Close the iPod door if notin use.Do not press the iPoddoor downwards when itis open as it may causedamage and injury.

2 Dock your iPod or iPhone into the unit.

iPod door

iPhone

Dock for iPhone

It is safe to disconnect iPod, iPhone and iPad even during playback. However attention should be drawn when removing the iPod or iPhone from docking station to avoid damage.

To disconnect iPod, iPhone or iPad

iPod or iPhone playback (dock only)

1 Press the ON/STAND-BY button to turn the power on.2 Press the iPod / button on the remote control or

the main unit to select iPod function.3 Insert iPod or iPhone unit into the dock of main unit.

“DOCK OK” will appear. Make sure to close the iPod door before playback.

4 Press the iPod / button to start playback.1 Press the ON/STAND-BY button to turn the power on.2 Press the USB button on the remote control or the

main unit to select USB function.

3 Connect iPod, iPhone or iPad to the unit. “USB/iPod” willappear.

Track number

4 Press the USB / button to start playback.

iPod, iPhone or iPad playback (USB only)

Cable holder

Thread the cables under the unit

REMOTE SENSOR

TIMER

PORTABLE MUSIC BOOMBOX GX-M10

ON/STAND-BY CD

Microphone or guitar (not supplied)

Ø 6.3 mm monoaural cable (not supplied)

1 Set the guitar/microphone volume (GAIN) knob to the minimum level.

2 Connect a guitar/microphone to the correct input socket. Make sure that the cable has a 6.3 mm (1/4”) diameter plug.

3 Arrange the guitar/microphone cables into the grooves of the cable holder on the left or the right side of the unit. Then, thread the cable through the bottom of the unit. Do not let the cables to be on top of the unit when using guitar/microphone as it may cause the unit to roll over causing damage and injury.

4 Connect the cables to a guitar/microphone.

5 Select a source. To mix a guitar or microphone sound with a source sound,

select the playback source (iPod/CD/USB/Audio In/Tuner). To play a guitar or using the microphone only, select ’AUDIO IN’

function. Make sure there is no playback from Audio In connection.

6 Adjust the volume (GAIN) knob on the connected equipment.

1 Press the ON/STAND-BY button to turn the power on.

2 Press the CD / button on the remote control or the main unit to select CD function.

3 Open the CD compartment by pushing the CD compartment open knob to the area marked ‘ ’.

4 Place the disc on the spindle, label side up.

5 Close the CD compartment.

6 Press the CD / button to start playback. After the last track is played, the unit will stop automatically.