+ All Categories
Home > Documents > Posi-Joist Details Rev 6 - Joist & Roof Truss Manufacturers

Posi-Joist Details Rev 6 - Joist & Roof Truss Manufacturers

Date post: 13-Mar-2022
Category:
Upload: others
View: 9 times
Download: 0 times
Share this document with a friend
37
MiTek Posi-Joist Details Rev 6.2 20171109
Transcript

MiTek Posi-Joist

DetailsRev 6.2

20171109

Block DetailsPSD33 - General Support Details Site Length AdjustmentPSD34 - General Support Details Internal Blocked Bearing Detail

Soil Vent Pipe DetailsPSD31 - Fixing Round SVP Using Bearer PlatesPSD32 - Fixing Round SVP Using Timber TrimmerCompartment Floor DetailPSD30 - Typical Timber Frame Compartment Floor / Party Wall Detail

Restraint DetailsPSD28 - Horizontal Restraint Strap Fixed To StrongbackPSD29 - Horizontal Restraint Strap Fixed To NoggingPSD29A - Horizontal Restraint Strap Fixed to Con nuous Nogging

Strongback DetailsPSD24 - Strongback Detail (Fixed To Site Added Blocks)PSD25 - Strongback Detail (Fixed To Built In Ver cal Webs)PSD26 - Strongback Bridging (Fixed To Built In Ver cal Webs)PSD27 - Strongback Splice (Fixed To Site Added Blocks)

Staircase opening DetailsPSD18 - 2 Ply Posi-Joist Trimming Girder and Posi-Joist Trimmer BeamPSD19 - 3 Ply Posi-Joist Trimming Girder and Posi-Joist Trimmer BeamPSD20 - Posi-Joist Trimming Girder and EWP Trimmer BeamPSD21 - Posi-Joist Trimming Girder and Solid Timber Trimmer Beam On HangersPSD22 - Solid Timber Or EWP Trimmer Beam Slotted Through Posi-Joist Trimming GirderPSD23 - EWP Stair Trimmer and Posi-Joist Trimmer Beam

Duct DetailPSD17 - Maximum Duct Sizes

Par on DetailsPSD15 - Non-Loadbearing Par ons Parallel To Posi-JoistsPSD16 - Non-Loadbearing Par ons Parallel To Posi-Joists

(Alterna ve Noggin Support Detail)

Internal DetailsPSD10 - Bo om Chord Support Timber Frame Internal Lapped

(With Full Depth Stru ng)PSD11 - Bo om Chord Support Timber Frame Internal Con nuous

(With Full Depth Stru ng If Required)PSD12 - Bo om Chord Support Masonry Internal Lapped PSD13 - Bo om Chord Support Masonry Internal Con nuous Or Bu ng EndsPSD14 - Bo om Chord Support Masonry Internal Con nuous With Solid Timber Block

End DetailsPSD01 - Posi-Joist To Girder DetailPSD02 - Bo om Chord Support Timber Frame External

(With Ring Beam And Packer)PSD03 - Bo om Chord Support Timber Frame Internal

(With Restraint Noggins)PSD04 - Top Chord Support Timber Frame Internal or ExternalPSD05 - Bo om Chord Support Masonry On Hanger With Top Noggin RestraintPSD06 - Bo om Chord Support Masonry Built InPSD07 - Top Chord Support Masonry Built In PSD08 - Bo om Chord Support Flush To Steel BeamPSD09 - Top Chord Support To Downstand Steel Beam

Index

Do not notch bo om chordof Posi-Joist over bo om

ange of hanger.

Posi-Joist girder chords xedtogether as speci ed by design.

Posi-Joist To Girder Detail

Note: Loaded face be clearly marked on Posi-Joist girder.

PSD01

Posi-JoistHanger

Bo om Chord SupportTimber Frame External

(With Ring Beam And Packer)

PSD02

Solid mber packer as speci ed by mberframe design

Solid or engineered mber ring beam with depth to suit.

Edge joist to befully webbedwith internalcrush blocksat max 1.8mcentres

Bo om Chord SupportTimber Frame

(With Restraint Noggins).

Full depth chord restraintblocking xed betweenPosi-Joists.

PSD03

Ring beam tosuit Posi-Joist depth.

Gap between end ofBottom Chord of Posi-Joist and plasterboard runner.

Con nuousplasterboardrunner.

Packing piece to suitPosi-Joist Top Chord

ange depth and ring beam width.

Unless proven by design the Posi-Strut shouldoverhang the bearingby 15mm.

Top Chord Support Timber Frame Internal or External

PSD04

Bo om Chord Support Masonry Hanger with Noggin Restraint

Top restraint noggings xedbetween Posi-Joists.

Masonry Joist Hanger.Do not notch bo om chordof Posi-Joist over bo om

ange of hanger.

Minimum bearing determined by design. Choose correct full depth hanger for coursework,load, bearing width and desired bearing level.

PSD05

Bo om Chord SupportBuilt into Masonry.

Blockwork to con nue between joists toprovide restraint.

Fully exible sealant toprovide air ghtness.

PSD06

Top Chord Support Built into Masonry

PSD07

Unless proven by design the Posi-Strut should overhang the bearing by 15mm

Bo om Chord Support to Steel Beam

Timber pack as speci ed by building designer xed to beam(size to suit).

Face xPosi-Joist hanger

PSD08

Top Chord Support Fixing To Downstand Steel Beam

Packing piece to suitPosi-Joist Top Chordflange depth and plate width.

Timber plate xedto top of steel.

Timber pack xed tobeam (size to suit)

Unless proven by design the Posi-Strut shouldoverhang the bearingby 15mm.

Gap between end ofBottom Chord of Posi-Joist and plasterboard runner.

PSD09

Bo om Chord SupportTimber Frame Internal Lapped

(With Full Depth Stru ng)

Single or double full depth blocking xed betweenPosi-Joists.

Posi-Joists lapped over wall.

PSD10

Bo om Chord SupportTimber Frame Internal Con nuous

(With Full Depth Stru ng If Required)

Solid or EWP full depth blockingrequired between Posi-Joistsonly if there is a load bearing wall above.

Studs posi oned beneath Posi-Joists.

PSD11

Bo om Chord Support Internal Masonry Lapped

Masonry built up to underside of oor toprovide restraint.

Note: Use on internal load bearing internal walls (not re walls).

Posi-Joists lapped over wall.

PSD12

Bo om Chord Support Internal Masonry Con nuous

or Bu ng Ends.

Masonry built up to underside of oor toprovide restraint.

(Minimum 45mm Bearing Required If Posi-Joist split on centre of wall.

PSD13

Bo om Chord Support Internal Masonry Con nuousJoist with solid mber block

Note: Use on internal load bearing internal walls (not re walls).

Solid mber block overbearing with grainparallel to span.

Gap to be lled toprovide air ghtness.

PSD14

Non-Loadbearing WallParallel with Posi-Joists.

Z clips.

38x89 C16 (min) noggins at max600mm centres.

Nogging nailed down onto wall panel as above.

Wall panel skew nailed through onto noggin with a min of 2 no3.35 dia galvanised wire nails,length to suit.

PSD15

Wall panel skew nailed through onto noggin with a min of 2 no3.35 dia galvanised wire nails,length to suit.

Non-Loadbearing Par ons Parallel To Posi-Joists

(Alterna ve Noggin Support Detail)

PSD16

Plated stacked noggin supportedon top ofbo om chord ofPosi-Joists

Maximum Duct Sizes

RECTANGLE WIDTH

RECTANGLE DEPTH50 75 100 125 150 175 200 225 250 275 300

POSIJOISTSIZE

W CIRCLEDIA SQUARE

PS-8

PS-9

PS-10

PS-12

PS-14

PS-16

108 105 95

131 124 115

159 150 135

210 190 155

279 250 200

327 272 220

270 180 90

100180240310

320

350

490

510 470 430 390 340 300 260 220 170 130 90

60110160200

70110160

80160210270

310

440 390

260 210

350 300 250

--- - - - - -

-

-

-

-

---

-

- - -

- -

- - -

--

W

PSD17

LARGE SERVICES MAY NEED TO BE OF FLEXIBLE MATERIAL TO BE ABLE TO BE FED THROUGH

THE VOIDS IN THE POSI-JOISTS

Opening with 2-ply Posi-Joist Girderand Posi-Joist Trimmer Beam

Posi-Joist girder chords xedtogether as speci ed by design.

Do not notch bo om chordof Posi-Joist over bo om

ange of hanger.

PSD18

Posi-JoistHangers

Posi-Joist girder chords xedtogether as speci ed by design.

Do not notch bo om chordof Posi-Joist over bo om

ange of hanger.

Opening With 3 Ply Posi-Joist Girder and Posi-Joist Trimmer Beam

PSD19

Posi-JoistHangers

Opening with Posi-Joist Girder and Solid or

EWP Trimmer Beam.

Solid or EWP trimmer(Depth to suit)

Packers to suitTrimmer size.

Posi-Joist girder chords xedtogether as speci ed by design.

Unless proven by design the Posi-Strut shouldoverhang the bearingby 15mm.

PSD20

Posi-JoistHangers

Packers to suitTrimmer size.

Posi-Joist girder chords xedtogether as speci ed by design.

Staircase Opening With Posi-JoistGirder and Solid Timber

Trimmer Beam On Hangers

PSD21

Posi-JoistHangers

Posi-Joist girder chords xedtogether as speci ed by design.

Packers to suitTrimmer size.

PSD22

Staircase Opening With Solid Timber Or EWP Trimmer Beam Slo ed

Through Posi-Joist Girder

Packing piece topick up ceiling

Solid mber or EWPtrimmer at depth tosuit slo ed through

girders

Do not notch bo om chordof Posi-Joist over bo om

ange of hanger.

Staircase Opening With EWP Stair Trimmer and

Posi-Joist Trimmer beam

PSD23

Twice nail brace to web using3.1 x 75mm long galvanised wire nails

Posi-JoistHangers

Strongback securelyxed to trimmer with

suitable hanger

Strongback DetailFixed to Site Added Blocks

38x75 (min) blocks twice nailed to top and bo om members and twice nailed to strongback using3.1x75mm long galvanised ring shank nails.

Minimum recommended strongback sizes are given above which may be di erent when oor is designed to

EC5 vibra on check, see Posi-Joist calcula ons ect.Posi on strongbacks ght to the underside of top chord.

(Fix at a maximum of 4.0 metre centres and within e ec ve zone)

INSERT STRONGBACK THROUGH POSI - JOISTSBEFORE FIXING AS IT CANNOT BE

INSTALLED AFTE THEY HAVE BEEN FIXED.

PSD24

WEB SIZE RECOMMENDED MINSTRONGBACK SECTION

PS-8, PS-9 & PS-10

PS12, PS-14 & PS16

47 x 97 TR26*

36 x 147 TR26*

Strongback DetailFixed To Built In Ver cal Webs

PSD25

(Fix at a maximum of 4.0 metre centres and within e ec ve zone)

Minimum recommended strongback sizes are given above which may be di erent when oor is designed to

EC5 vibra on check, see Posi-Joist calcula ons ect.Posi on strongbacks ght to the underside of top chord.

INSERT STRONGBACK THROUGH POSI - JOISTSBEFORE FIXING AS IT CANNOT BE

INSTALLED AFTE THEY HAVE BEEN FIXED.

WEB SIZE

PS-8, PS-9 & PS-10

PS12, PS-14 & PS16

RECOMMENDED MINSTRONGBACK SECTION

47 x 97 TR26*

36 x 147 TR26*

Twice nail brace to web using3.1 x 75mm long galvanised wire nails

Twice nail brace to web using 3.1x75mm long galvanised wire nails.

Strongback DetailFixed To Built In Ver cal Webs

PSD26

Minimum recommended strongback sizes are given above which may be di erent when oor is designed to

EC5 vibra on check, see Posi-Joist calcula ons ect.Posi on strongbacks ght to the underside of top chord.

(Fix at a maximum of 4.0 metre centres and within e ec ve zone)

INSERT STRONGBACK THROUGH POSI - JOISTSBEFORE FIXING AS IT CANNOT BE

INSTALLED AFTE THEY HAVE BEEN FIXED.

WEB SIZE RECOMMENDED MINSTRONGBACK SECTION

PS-8, PS-9 & PS-10

PS12, PS-14 & PS16

47 x 97 TR26*

36 x 147 TR26*

38x75 (min) blocks twice nailed to top and bo om members and twice nailed to strongback using3.1x75mm long galvanised annular ringshank nails.

1200mm long splice xed with 10no3.1x90mm long galvanised annular ringshanknails each side of splice, nailed through and clenched over on far side.

Strongback SpliceFixed to Site Added Blocks

PSD27

Horizontal Restraint StrapFixed to Strongback

Strap xed along top edge of strongback.Refer to strap manufacturers details for

xing method.

Strongback twice nailed to brace using min 3.1x75mm long galvanised annular ringshanknails.

PSD28

Horizontal Restraint StrapFixed To Noggins

Strap xed to noggin. Refer to strapmanufacturers details for xing method.

min 35 x 72 C16 noggin xed between joists.

PSD29

Horizontal Restraint StrapFixed to Con nuous Noggin

Strap xed along top edge of strongback.Refer to strap manufacturers details for

xing method.

35x97 C16 Noggin nailed to underside of top chord of Posi-Joist using 3.1x75mm long galvanised annular ringshank nails.

PSD29A

Typical Timber Frame Compartment Floor / Party Wall Detail

47x 89 Packsbetween joists

Posi-JoistsParallel to wall

Posi-Joistsbearing on wall

47x 89 Con nuous Pack

Floa ng Floor Comprising:-18mm T & G Chipboard on 19mm plasterboard plank on 25mm Fibreglass Slab on 18mm T & G Chipboard. All T & G edges glued, and 19mm plank bonded to chipboard with dabs of Gyproc sealant at 300mm centres. Joints between chipboard and plasterboard to be staggered and board direc on reversed.

Bead of sealent applied to oor deck proir to xing19mm plasterboard plank

100mm Mineral wool insula onquilt 23kb/m2

Mineral wool cavity barrier

2 no 30 x 200mm GMSStraps at 1200mm centres

Posi-web overbearing by min15mm

200approxFirst Posi-Joist beamset back from wallby approx 200mm

Plasterboard noggins

Ring Beams in solid mber or LVL

Ceiling (not shown) comprising:-2 Layers 15mm Gyproc Fireline Board on 16mm resilient bars at 400mmcentres. First layer xed with 38mm Gyproc screws at 230mm centres.Second layer xed with 60mm Gyproc screws at 230mm centres.Staggered with rst layer screws.Lay Firleline board in echelon pa ern with staggered joints.

PSD30

Fixing Round SVPusing Bearer Plates

Note: This may not perform well acous callyas sound will be transmi ed directly from the oor tothe bearer through the inner leaf of the wall.

Bearers xed to wall at oor and ceiling level.

Posi-Joist adjacent to SVP shown in full depth masonry hanger.

Soil Vent Pipe (SVP).

PSD31

Soil Vent Pipe (SVP).

Packer

Face Fix Joist Hanger(Solid Trimmer to Posi-Joist)

Solid Trimmer to built into wall.

Fixing Round SVPusing Solid Trimmer.

PSD32

Unless proven by design the Posi-Strut should overhang thebearing by 15mm

Side eleva on

65

130mm max adjustment

Max 130mm to betrimmed on site

330mm

330mm

5555

130mm max adjustment

47

GrainDirec on

PSD33

47

55 55

330mm solid block from dry well seasoned mber

ght xed at manufacture

Block nailed to top and bo om chords using6 no. 3.1mm diameter 90mm long power driven

annular ring-shank nails at 44mm centres.

Plan view of Posi-Joistwith one block

Two blocksrequired when

chords are122mm or 147mm

Plan view of Posi-Joistwith two blocks

Block nailed to top and bo om chords using6 no. 3.1mm diameter 90mm long power driven

annular ring-shank nails at 44mm centres.

General Support DetailsSite Length Adjustment

General Support DetailsInternal Blocked Bearing Detail

Plan view of Posi-Joistwith one block

Block nailed to top and bo om chords using7 no. 3.1mm diameter 90mm long power driven

annular ring-shank nails at 48mm centres.

Plan view of Posi-Joistwith two blocks

Side eleva on

Block nailed to top and bo am chords using7 no 3.1mm diameter 90mm long power driven

annular ring-shank nails at 48mm centres.

400mm solid block from dry well seasoned mberght xed at manufacture

Two blocksrequired when

chords are122mm or 147mm

PSD34

GrainDirec on

55 55

47

400mm

400mm

55 55

47


Recommended