Power System PPS 7 - Steven Engineering · 2004. 3. 24. · Rectifier Features Model Voltage Power...

Features• High reliability• Simple installation and operation• LCD display for self-guided controller operation• RS232 interface for remote operation• Intelligent battery management:

• Temperature compensation(requires optional cables)

• Programmable battery load testing with data logging

• Symmetry (requires optional cables)• Programmable low voltage disconnect

• Optional Ethernet (SNMP compatible) interface module

• Natural convection cooling - no fans• International standards compliance

DescriptionPPS 7 modular DC power shelf systemsprovide large power system features incost-effective, rack-mounted form factors.These shelf power solutions providerectification, system management, andpower distribution while maintaining highreliability and offering flexibility for futureexpansion. The PPS 7 systems are basedon hot-swappable rectifier modules outputpower available at 450, 560 or 670W permodule.

System management is accomplishedthrough messages and alarms displayedon the system controller’s (PCU) LCDscreen and can also be displayedremotely via the PC-based PowComTM

software package. Note: All specifications are subject to change without notification.

Input

Output

Mechanical

Options

Features

Battery

Model PPS 7-2100 PPS 7-2800 PPS 7-3500 PPS 7-4200

Input230/400V 3-phase208-240V 1-phaseSite configurable

230/400V 3-phase208-240V 1-phaseSite configurable



Inputs (max.) Single input Single input Single input Single input

Rectifier Modules (max.) 3 4 5 6

Battery Outputs 1 1 2 2

Load Outputs 6 1 20 24

24V DC Version Yes N/A N/A N/A

48V DC Version Yes Yes Yes Yes

60V DC Version Yes (on request) Yes (on request) Yes (on request) Yes (on request)

Supervision PCU PCU PCU PCU

Battery Symmetry Inputs(max.)

1 1 3 3

Low Voltage BatteryDisconnection (LVBD) Yes Yes Yes Yes

Dimensions (WxHxD) 485x133x305mm 485x133x305mm 485x133x305mm 582x266x305mm

Mounting19”, ETSI, or flushETSI mount (site configurable)

19”, ETSI, or flushETSI mount (site configurable)


23”

Cable Entry Top Top Top Top

Temp. Comp. Charge Yes Yes Yes Yes

Ethernet NetworkInterface Yes Yes Yes Yes

Modem Interface Yes Yes Yes Yes

PPS 7 Power SystemShelf System

www.power-one.comwww.power-one.com

Shelf System

11V0005-036 PPS7 SY V3.0

PPS 7 Power System

Rectifier Features

Model Voltage Power(max.)Current(max.)

PMP 5.24 SIC 110* 24V DC 448W 16A

PMP 5.48 SIC 110* 48V DC 448W 8A

PMP 7.24 SIC 24V DC 560W 20A

PMP 7.48 SIC 48V DC 672W 12A

PMP 7.60 SIC 60V DC 635W 9A

The PPS 7 system utilizes plug-in rectifier modules that arebased on a soft-switching approach. Features include 3 LEDsfor rectifier status indication, thermal shutdown, and inputovervoltage disconnection with an automatic reset (only onPMP 7 modules).

• Menu guided operation• RS232 interface for remote operation• Battery management and testing• Low voltage battery disconnect (LVBD)• Temperature compensation• Battery symmetry measurement• Optional Ethernet interface through SNMP and/or TCP/IP• Partial load disconnection (PLD)

PCU Features

Rectifier Modules

Advanced system supervision is accomplished using amicroprocessor based control module that allows both localand remote system monitoring.

Supervision Modules

An all-in-one 3U high shelf system that can beinstalled in both 19” and ETSI telecom cabinetsolutions. The system subrack canaccommodate up to three rectifier modules, asupervision module (PCU) and DC distributionwith a single battery breaker and six loadbreakers.

PPS 7-2100 SystemAn all-in-one 3U high shelf system that can beinstalled in both 19” and ETSI telecom cabinetsolutions. The system subrack canaccommodate up to four rectifier modules, asupervision module (PCU) and DCdistribution with a single battery breaker and asingle load breaker.

PPS 7-2800 System

An all-in-one 6U high shelf system that can beinstalled in 23” standard telecom cabinetsolutions. The system subrack canaccommodate up to six rectifier modules, asupervision module (PCU) and DC distributionwith up to two battery breakers and twentyfour load breakers.

PPS 7-4200 SystemAn all-in-one 6U high shelf system that can beinstalled in 19” and ETSI telecom cabinetsolutions. The system subrack canaccommodate up to five rectifier modules, asupervision module (PCU) and DC distributionwith up to two battery breakers and twentyload breakers.

PPS 7-3500 System

*110V AC input

System Configurations System Components


Features• High reliability• Simple installation and operation• LCD display for self-guided controller operation• RS232 interface for remote operation• Intelligent battery management:

• Temperature compensation(requires optional cables)

• Programmable battery load testing with data logging

• Symmetry (requires optional cables)• Programmable low voltage disconnect

• Optional Ethernet (SNMP compatible) interface module

• Natural convection cooling - no fans• International standards compliance

DescriptionPPS 7 modular DC power shelf systemsprovide large power system features incost-effective, rack-mounted form factors.These shelf power solutions providerectification, system management, andpower distribution while maintaining highreliability and offering flexibility for futureexpansion. The PPS 7 systems are basedon hot-swappable rectifier modules outputpower available at 450, 560 or 670W permodule.

System management is accomplishedthrough messages and alarms displayedon the system controller’s (PCU) LCDscreen and can also be displayedremotely via the PC-based PowComTM

software package. Note: All specifications are subject to change without notification.

Input

Output

Mechanical

Options

Features

Battery

Model PPS 7-2100 PPS 7-2800 PPS 7-3500 PPS 7-4200

Input230/400V 3-phase208-240V 1-phaseSite configurable




Inputs (max.) Single input Single input Single input Single input

Rectifier Modules (max.) 3 4 5 6



24V DC Version Yes N/A N/A N/A

48V DC Version Yes Yes Yes Yes

60V DC Version Yes (on request) Yes (on request) Yes (on request) Yes (on request)

Supervision PCU PCU PCU PCU

Battery Symmetry Inputs(max.)

1 1 3 3

Low Voltage BatteryDisconnection (LVBD) Yes Yes Yes Yes

Dimensions (WxHxD) 485x133x305mm 485x133x305mm 485x133x305mm 582x266x305mm

Mounting19”, ETSI, or flushETSI mount (site configurable)



23”

Cable Entry Top Top Top Top

Temp. Comp. Charge Yes Yes Yes Yes

Ethernet NetworkInterface Yes Yes Yes Yes

Modem Interface Yes Yes Yes Yes


www.power-one.comwww.power-one.com

Shelf System

11V0005-036 PPS7 SY V3.0

PPS 7 Power System

DescriptionThe Power-One PMP 5 rectifier moduleprovides a cost-effective power solutionin a high density footprint. Built on thelatest advances in the resonance switchmode approach (soft-switching), thePMP 5 is the next evolution in our smallconvection cooled rectifier series.

Optimized for telecom applications, themodule is designed to work in amultitude of different subrack/shelfconfigurations incorporating the Power-One PCU controller and variousdistribution options.

Features• 115/230 VAC input• 24V, or 48VDC output• Power factor correction• Active load sharing• Hot-swappable• International standards compliance• Natural convection cooling• Low weight

PPS 5/7 SystemShown

PMP 5Rectifier Module

www.power-one.com

InputModel PMP 5.24 PMP 5.48 PMP5.24-110

PMP5.48-110

InputVoltage

161-276V AC singlephase, (44-66Hz)

80-138V AC singlephase, (44-66Hz)

Current(max.) 87% >87%

Tolerance Vout +/- 1%

TransientResponse

+/- 5% at load variation 10-90% or 90-10%,recovery time 10ms

Load Sharing

DescriptionThe Power-One PMP 7 rectifier moduleprovides a cost-effective power solutionin the highest possible density. Built onthe latest advances in the resonanceswitch mode approach (soft-switching),the PMP 7 is the next evolution in oursmall convection cooled rectifier series.

Optimized for telecom applications, themodule is designed to work in a multitudeof different subrack/shelf configurationsincorporating the Power-One PCUcontroller and various distributionoptions.

Features• 208/240 VAC input• 24V, 48V, or 60V DC output• Input overvoltage disconnection• Thermal protection• Active load sharing• Hot-swappable• Up to 92% efficient• International standards compliance• Natural convection cooling• Low weightPPS 7 3500 System

Shown


www.power-one.com

InputModel PMP 7.24 PMP 7.48 PMP 7.60

InputVoltage

205-250V AC ±10% single phase, (44-66Hz) (-15% for PMP7.60)185-160V at reduced output power

Current(max.)

The PCU 5/ 7Controllers are usedin PPS5 and PPS7Power Systems.

DescriptionThe Power-One Control Unit (PCU 5/7) provides monitoring and control for the PPS 5 and PPS 7power systems. These hot-swappable controller modules supervise output voltages, currents, rectifierperformance, battery condition, and breaker status. Visual notification of an alarm condition isprovided with an LED. A description of the exact alarm condition is provided through an LCD.Additionally, four Form “C” contacts are provided to indicate a failure.

FeaturesUser controls and interfaces:

• Simple menu-guided operation using front panel mounted pushbuttons and an LCD

• User-selectable alarm parameters

• Data logging of last 40 events

• SNMP interface adapter available

• RS232 interface and Form “C” dry alarm contacts

• Compatible with PowComTM PC-based software

PCU 5/7Controller

www.power-one.com

Intelligent battery management:

• Temperature compensation with programmable compensation factor

• Automatic and manual load testing

• Battery voltage and symmetry monitoring

• Capacity testing

• Low voltage disconnect

InputVoltage 18-72V DC

Current

DescriptionThe Power-One PPR 5/7 3 and 6position rectifier backplane provides acost-effective power solution in a highdensity wall-mounted footprint. Thesepower solutions provide rectification,system management, and powerdistribution while maintaining highreliability and offering flexibility forfuture expansion. The PPS 5/7 3 & 6Position systems are based on hot-swappable rectifier modules outputpower available at 450, 560 or 670W permodule.

Features• 115/230 VAC input• 24V, or 48VDC output• Serial or parallel alarm configurations• Active load sharing• Hot-swappable• International standards compliance• Natural convection cooling• Systems can be paralleled• Individual rectifier output adjustment6 Position SystemShown

PPR 5/73 & 6 Position Power Systems

www.power-one.com

www.power-one.com11V0005-065 PPR 5/7 V3.0

PPR 5/73 & 6 Position Power Systems

Note: All specifications are subject to change without notification.

Input

Output

Mechanical

Features

Model PPR 5/7 3-Position PPR 5/7 6-Position

Input115 or 230VAC single phase(Depending on rectifiermodule)"

115 or 230VAC single phase(Depending on rectifiermodule)"

Input Connections 3x4mm² terminal blocks 3x4mm² terminal blocks

Rectifier Modules (max.) 3 6

Load Outputs 2x10mm² - Qty 3 2x10mm² - Qty 6

24V DC Version Yes Yes


AlarmsCommon alarm for High Voltage/ Shutdown, Low Voltage/Module Failure, Unequal Load Sharing Normally Openedor Normally Closed.

Dimensions (WxHxD) 271x193.5x305mm 484.4x193.5x305mm

Weight 1.2kg (2.65lbs.) 2.5kg (5.5lbs.)

Mounting Wall Mount Wall Mount

Model Voltage Power (max.) Current (max.)

PMP 5.24 24V DC 448W 16A

PMP 5.24 SIC 110* 24V DC 448W 16A

PMP 5.48 SIC 110* 48V DC 448W 8A

PMP 7.24 SIC 24V DC 560W 20A

PMP 7.48 SIC 48V DC 672W 12A

*110V AC input

Available Rectifiers

Features• High reliability• Simple installation and operation• Natural convection cooling - no fans• RS232 interface for remote operation• Form “C” dry alarm contacts• Intelligent battery management• Pluggable controller and DC distribution

modules• Optional Ethernet (SNMP compatible) interface

module • International standards compliance

DescriptionThe Galero™ Power System provideslarge power system features in cost-effective, rack-mounted form factors.These power solutions providerectification, control and powerdistribution all in one compact systemwhile offering extensive local and remotepower system and battery monitoring.

System management is accomplishedthrough the system controller (GMC).Status indication is made via LED’s, whiledetailed information and remote operationare accomplished through the PC-basedPowComTM software package.


Input

Output

Mechanical

Options

Features

Battery

Model Galero 1750 Galero 2450

Input230/400V AC 3-phase205-240V AC 1-phaseSite configurable

230/400V AC 3-phase205-240V AC 1-phaseSite configurable

Inputs (max.) Single input Single input





Supervision GMC GMC

Battery Symmetry Inputs (max.) 2 2

Low Voltage BatteryDisconnection (LVBD) Yes Yes

Temp. Comp. Charge Yes Yes

Dimensions (WxHxD) 483x125x280mm 483x125x280mm

Mounting 19”, ETSI 19”, ETSI

Cable Entry AC - RearDC and signals -TopAC - RearDC and signals -Top


Battery SymmetryMeasurement Yes Yes

Ethernet Network Interface Yes Yes

Partial Load Disconnect N/A N/A

Integrated Surge Arrestors N/A N/A

Galero™ Power System

www.power-one.comwww.power-one.com11V0005-033 Galero SY V3.0

Galero™ Power SystemShelf SystemShelf System

Rectifier Features

Model Voltage Power(max.)Current(max.)

CMP 3.48 48V DC 364W 6.5A

The Galero Shelf System utilizes plug-in rectifiermodules based on a soft-switching approach.Features include 2xLED for rectifier status indication,thermal protection with de-rating and input over-voltage disconnection with automatic reset.

• Advanced system monitoring• RS232 interface for remote operation• Battery management and testing• Automatic testing• Low voltage battery disconnect (LVBD)• Temperature compensation• Battery symmetry measurement• Monthly logging of battery parameters including “temperature-hours”• Site programmable Flash EPROM• Programmable alarms• Programmable logic circuit• Optional Ethernet interface through SNMP and/or TCP/IP

GMC Features

Rectifier Module

Advanced system supervision is accomplished using amicroprocessor based module that allows both local andremote system monitoring.

Supervision Module - GMC

All-in-one 125 mm high shelf system for integration into standard19” or ETSI cabinets. Complete subrack for five rectifier modules, supervision moduleand DC distribution with battery breakers (1-2) and load breakers(9-10).

Galero 1750 System

All-in-one 125 mm high shelf system for integration intostandard 19” or ETSI cabinets. Complete subrack for seven rectifier modules, supervisionmodule and DC distribution including battery breakers (1-2) andload breakers (2-3).

Galero 2450 System


Galero™ Power SystemShelf System

Features• High reliability• Simple installation and operation• Natural convection cooling - no fans• RS232 interface for remote operation• Form “C” dry alarm contacts• Intelligent battery management• Pluggable controller and DC distribution

modules• Optional Ethernet (SNMP compatible) interface

module • International standards compliance

DescriptionThe Galero™ Power System provideslarge power system features in cost-effective, rack-mounted form factors.These power solutions providerectification, control and powerdistribution all in one compact systemwhile offering extensive local and remotepower system and battery monitoring.

System management is accomplishedthrough the system controller (GMC).Status indication is made via LED’s, whiledetailed information and remote operationare accomplished through the PC-basedPowComTM software package.


Input

Output

Mechanical

Options

Features

Battery

Model Galero 1750 Galero 2450

Input230/400V AC 3-phase205-240V AC 1-phaseSite configurable

230/400V AC 3-phase205-240V AC 1-phaseSite configurable

Inputs (max.) Single input Single input





Supervision GMC GMC

Battery Symmetry Inputs (max.) 2 2

Low Voltage BatteryDisconnection (LVBD) Yes Yes


Dimensions (WxHxD) 483x125x280mm 483x125x280mm

Mounting 19”, ETSI 19”, ETSI

Cable Entry AC - RearDC and signals -TopAC - RearDC and signals -Top


Battery SymmetryMeasurement Yes Yes

Ethernet Network Interface Yes Yes

Partial Load Disconnect N/A N/A

Integrated Surge Arrestors N/A N/A

Galero™ Power System

www.power-one.comwww.power-one.com11V0005-033 Galero SY V3.0

Galero™ Power SystemShelf SystemShelf System

DescriptionThe Power-One CMP 3.48, for use in theGalero™ series of power systems, is thenext evolution in our convection cooledrectifier series. This module provides thelatest advances in resonance switch modetechnology (softswitching). An onboardmicrocontroller and an RS 485 data busprovide monitoring of basic functions, statusand identification information to the systemcontroller (GMC).

The CMP 3.48 rectifier module is optimizedfor telecom applications and is designed towork in numerous subrack/shelfconfigurations incorporating the GMCcontroller and varying distribution options.

Features• 208/240 VAC input• 48 VDC output• Input over-voltage disconnection• Thermal protection, with de-rating• Active load sharing• Hot-swappable • Up to 91% efficient• Natural convection cooling• Low weight• International Standards Compliance

Galero™ PowerSystem

CMP 3.48Rectifier Module

www.power-one.com

InputModel CMP 3.48

Input Voltage205-240V AC +10% single phase,44-66Hz(185-160V at reduced power output)

Current (max.) 91%

Tolerance Vout +/- 1.0%,

TransientResponse

+/- 5% at load variation 10-90% or 90-10% recovery time 10ms

Load Sharing Typical 250VAC.

Indications

Green LED

Red LED

Power ON

High outputvoltage/ shut downLow voltage/module failure

AudibleNoise

DescriptionThe Galero™ Microprocessor Controller (GMC) from Power-One provides comprehensive monitoring andcontrol of the Galero power system. This digital controller monitors total system conditions including DCvoltage, rectifier current, rectifier temperature, system capacity, battery parameters and circuit breakerstatus.

The GMC enables data storage of system configuration information such as battery type, installation dateand system commission date. Visual notification of alarm and warning conditions are indicated by frontpanel LEDs, while descriptions of the alarms are provided through RS232 communication using PC-basedPowCom™ software package.

To meet individual site requirements, the GMC contains a Programmable Logic Unit that can beprogrammed to monitor and control specified requirements. This allows actions to be set, alarms to betriggered and outputs to be activated based on internal and external signal monitoring, comparing andprocessing.



• 40 event data logging

• Password controlled environment

• RS232 Interface and Form “C” dry alarm contacts

• Programmable routing alarm

• Programmable logic unit

GMCController Module

www.power-one.com







• Optional plug-in Ethernet interface (PNI module)


Current

Input

Input Voltage 180-264 VAC

Frequency 47-63Hz

Input Current 9.33A @180VAC

Power Factor >.98 Typical

Output

Alarms

Alarm History 40 event alarm history

AlarmContacts

Four free alarm contacts (max.60V, 1A) Two open collectoroutputs for LVD

Alarms High DC VoltageLow DC VoltageLoad/ Battery DisconnectionBattery Fuse FailureDC Fuse FailureModule FailureMain AC FailureBattery FailureSymmetry FailureHigh TemperatureHigh Load

Voltage 42V-58VDC (54VDC Nominal)

Output up to 500A in 4 subrack/ shelfsystem

Power (at 208/240VAC)

1350W (up to 50°C) per rectifier1200W (up to 65°C) per rectifier

Efficiency 90% typical

MechanicalDimensions(WxHxD)

584.2/482.6 x 133.35 x 274.32mm(23/19 x 5.25 x 10.8in.)

Shelf withoutController

584.2/482.6 x 88.9 x 274.32mm(23/19 x 3.5 x 10.8in.)

Mounting 19/23in. rack mount

Cooling Fan Cooled, speed controlled andalarmed

Other Technical DataOperatingTemperature

-40 to +65°C, (Derated to 700W from 65 to 75°C)

StorageTemperature -40 to +85°C

Vibration/ ShockTolerance (NEBS) GR-63-CORE Level 3

Earthquake Zone 4 compliant

Safety CSA C22-2 No. 950, UL 1950 andIEC60950/ EN 60950

ESD Immunity EN61000-4-2, Level 4

RF Immunity EN61000-4-2, Level 3

Surge Immunity IEC/ EN61000-4-5, Level 4

Fast Transient/Burst Immunity IEC/ EN61000-4-4, Level 4

Battery

BatteryDisconnection

An optional feature that allowsvoltage or time controlleddisconnection of batteries.

BoostCharging

Manual time controlled orautomatic boost charging withadjustable time and voltagelevels.

Battery Test

Automatic or manual testing ofbatteries up to four times peryear. Variables include: testduration, end voltage, Ah, andallowable symmetry variation.

SymmetryMeasurement

Optional tool that measuresbatteries for early detection ofthermal runaway. Allows forseparate measurements of up tothree parallel battery branches,each divided into four blocks.

TemperatureCompensationCharging

Allows continuous adjustment ofoutput voltage according tobattery temperature. Featureincludes adjustablecompensation factor andseparate thresholds for alarms.


DescriptionXscend™, the new shelf based power system from Power-One is designed to meet a broad range of customer applicationsthrough flexibility, simplicity and scalability.

FlexibleThe Xscend power system offers solutions that meet today's demands by addressing tomorrow's problems, including: powerdensity, reliability, accessibility, upgrades, and space requirements. Utilizing state-of-the art rectifier technology, an integratedmicroprocessor controller platform and interchangeable distribution modules, the Xscend power system provides a diversefront-access power solution in only a 3 rack unit (5.25in.) vertical and a 300mm (12in.) deep cabinet area. Xscend rectifiersoperate using a phase shifted transitional resonant zero-voltage switching technology that offers increased system life andreliability by reducing component stresses. The same engineering strategy gives Xscend the ability to generate up to 1350Win just 3.5-inch (2RU) of vertical space, resulting in a power density of over 9 W/in

3. In addition, Xscend’s forward thinking

horizontal cooling design allows shelves to be placed directly above or below customer equipment, safely increasing theamount of space that can be used for revenue generating equipment and negating the need for airflow clearance above orbelow the unit.

SimpleThe Xscend power system is designed for ease of use through itsinnovative control and monitoring system. To accomplish this theXscend is supervised by a single rack unit microprocessorcontroller (XCS) that offers user-friendly menus and commandsthat allow an operator to monitor system conditions, capacity,battery parameters and circuit breaker status.

System control can also be accomplished by using an RS232digital communication bus that allows for remote operation througha Modem, Ethernet (SNMP capable), or standard form C contacts.The XCS controller also works hand-in-hand with the easy to usePower-One POWCOM software package that allows for totalsystem assessment and password controlled parameteradjustments.

ScalableIn keeping with today's unpredictable market requirements, Power-One's Xscend design targets a mechanical package approach thatpermits the power system to expand with ease.

Each 23 inch shelf can be fitted with up to five rectifier unitsdelivering up to 125A of system power, while each 19 inch rack canbe fitted with up to four rectifiers providing 100A. Additionalshelves, distributions and rectifiers can be added to a systemoffering a high system level density as well as system levelmodularity providing low start up costs and an easy growth path.

Features• AC Input 180-264 Vac

• 48VDC Rectifier with up to 1350W output

• 24V available during 2nd release

• Fan cooled rectifier modules

• Front access design

• Temperature hardened -40°C to +65°C

• 19” or 23” mounting arrangement

• Extensive remote monitoring capabilities

• Modular DC distribution with LVD

• Power Factor Correction

• ETSI Compatible

• Modular system from 25A to 500A

Shelf System

Xscend™ Power SystemShelf System

www.power-one.comwww.power-one.com11V0005-060 Xscend SY V3.0

Xscend™ Power System

Xscend Configuration OptionsIn today's changing market, companies require systems that can beeasily adjusted to meet a number of different configurations. To fillthis need, Power-One has designed Xscend to accommodatemultiple configurations through a modular system of shelf, rectifier,control and distribution options.

Xscend's options vary from single 1350W rectifier shelf system withan internal hot-add distribution module up to four paralleled rectifiershelves with an external distribution providing 500A. This scalableformat allows Xscend to be upgraded from a basic configurationthrough the addition of shelves and rectifiers.

Additional configuration designs are available upon request forcustomer specific racks, cabinets, or outdoor enclosures.

Shelf Output Specifications(Maximum output)

5 RectifiersOutput current: 125AOutput power: 6750W





Quad Shelf System• Up to 20 rectifier modules• 1 external distribution module with various

circuit breaker configuration options• Up to 27kW

Single Shelf System• Up to 5 rectifier modules• 1-2 distribution modules• Up to 5 circuit breakers• Up to 2 battery breakers• Up to 6750W

Double Shelf System• Up to 10 rectifier modules• 1-2 distribution modules• Up to 10 circuit breakers• Up to 4 battery breakers• Up to 13kW

System Configurations


Xscend Rectifier ModulePower-One has addressed the critical issue of power density bydesigning the Xscend rectifier module to be more compact, sothat the maximum amount of power can be generated in theleast amount of space. The module incorporates the latest inpower monitoring solutions through an internal microprocessor,giving up to the second updates on system performance. The rectifier is cooled by a high-speed temperature controlledfan that allows operation at 1200W at temperatures up to 65°C(reduced capacity to 75°C). These features allow the Xscendrectifier to operate in many different environments andconfigurations.

Xscend Distribution ModuleA common problem in today's power systems is cablecongestion. The Xscend system alleviates this problem throughan innovative module design that incorporates a standard cablemanagement area into the system. The result is a front access3-rack unit power system that allows for efficient and easyinstallation.This hot-add distribution modules have the option of beinginstalled into the two rightmost positions in the subrack, therebyallowing shelves and systems to be easily and quicklyconfigured as desired. This design allows each module todistribute and protect loads up to a total of 100A. Offered as anoption, the low voltage disconnect (LVD) function may beinstalled in each module to ensure system batteries areprotected against an irrecoverable discharge.

System Components

Input

Input Voltage 180-264 VAC

Frequency 47-63Hz

Input Current 9.33A @180VAC

Power Factor >.98 Typical

Output

Alarms

Alarm History 40 event alarm history

AlarmContacts

Four free alarm contacts (max.60V, 1A) Two open collectoroutputs for LVD

Alarms High DC VoltageLow DC VoltageLoad/ Battery DisconnectionBattery Fuse FailureDC Fuse FailureModule FailureMain AC FailureBattery FailureSymmetry FailureHigh TemperatureHigh Load

Voltage 42V-58VDC (54VDC Nominal)

Output up to 500A in 4 subrack/ shelfsystem

Power (at 208/240VAC)

1350W (up to 50°C) per rectifier1200W (up to 65°C) per rectifier


MechanicalDimensions(WxHxD)

584.2/482.6 x 133.35 x 274.32mm(23/19 x 5.25 x 10.8in.)

Shelf withoutController

584.2/482.6 x 88.9 x 274.32mm(23/19 x 3.5 x 10.8in.)

Mounting 19/23in. rack mount

Cooling Fan Cooled, speed controlled andalarmed

Other Technical DataOperatingTemperature

-40 to +65°C, (Derated to 700W from 65 to 75°C)


Vibration/ ShockTolerance (NEBS) GR-63-CORE Level 3

Earthquake Zone 4 compliant

Safety CSA C22-2 No. 950, UL 1950 andIEC60950/ EN 60950

ESD Immunity EN61000-4-2, Level 4

RF Immunity EN61000-4-2, Level 3

Surge Immunity IEC/ EN61000-4-5, Level 4

Fast Transient/Burst Immunity IEC/ EN61000-4-4, Level 4

Battery

BatteryDisconnection

An optional feature that allowsvoltage or time controlleddisconnection of batteries.

BoostCharging

Manual time controlled orautomatic boost charging withadjustable time and voltagelevels.

Battery Test

Automatic or manual testing ofbatteries up to four times peryear. Variables include: testduration, end voltage, Ah, andallowable symmetry variation.

SymmetryMeasurement

Optional tool that measuresbatteries for early detection ofthermal runaway. Allows forseparate measurements of up tothree parallel battery branches,each divided into four blocks.

TemperatureCompensationCharging

Allows continuous adjustment ofoutput voltage according tobattery temperature. Featureincludes adjustablecompensation factor andseparate thresholds for alarms.


DescriptionXscend™, the new shelf based power system from Power-One is designed to meet a broad range of customer applicationsthrough flexibility, simplicity and scalability.

FlexibleThe Xscend power system offers solutions that meet today's demands by addressing tomorrow's problems, including: powerdensity, reliability, accessibility, upgrades, and space requirements. Utilizing state-of-the art rectifier technology, an integratedmicroprocessor controller platform and interchangeable distribution modules, the Xscend power system provides a diversefront-access power solution in only a 3 rack unit (5.25in.) vertical and a 300mm (12in.) deep cabinet area. Xscend rectifiersoperate using a phase shifted transitional resonant zero-voltage switching technology that offers increased system life andreliability by reducing component stresses. The same engineering strategy gives Xscend the ability to generate up to 1350Win just 3.5-inch (2RU) of vertical space, resulting in a power density of over 9 W/in

3. In addition, Xscend’s forward thinking

horizontal cooling design allows shelves to be placed directly above or below customer equipment, safely increasing theamount of space that can be used for revenue generating equipment and negating the need for airflow clearance above orbelow the unit.

SimpleThe Xscend power system is designed for ease of use through itsinnovative control and monitoring system. To accomplish this theXscend is supervised by a single rack unit microprocessorcontroller (XCS) that offers user-friendly menus and commandsthat allow an operator to monitor system conditions, capacity,battery parameters and circuit breaker status.

System control can also be accomplished by using an RS232digital communication bus that allows for remote operation througha Modem, Ethernet (SNMP capable), or standard form C contacts.The XCS controller also works hand-in-hand with the easy to usePower-One POWCOM software package that allows for totalsystem assessment and password controlled parameteradjustments.

ScalableIn keeping with today's unpredictable market requirements, Power-One's Xscend design targets a mechanical package approach thatpermits the power system to expand with ease.

Each 23 inch shelf can be fitted with up to five rectifier unitsdelivering up to 125A of system power, while each 19 inch rack canbe fitted with up to four rectifiers providing 100A. Additionalshelves, distributions and rectifiers can be added to a systemoffering a high system level density as well as system levelmodularity providing low start up costs and an easy growth path.

Features• AC Input 180-264 Vac

• 48VDC Rectifier with up to 1350W output

• 24V available during 2nd release

• Fan cooled rectifier modules

• Front access design

• Temperature hardened -40°C to +65°C

• 19” or 23” mounting arrangement

• Extensive remote monitoring capabilities

• Modular DC distribution with LVD

• Power Factor Correction

• ETSI Compatible

• Modular system from 25A to 500A

Shelf System


www.power-one.comwww.power-one.com11V0005-060 Xscend SY V3.0

Xscend™ Power System

DescriptionThe Power-One Xscend™ rectifier providesextremely reliable DC power in the highestpossible density. The module incorporatesthe latest in power monitoring solutionsthrough an internal microprocessor giving upto the second updates to the systemcontroller and adjacent rectifiers. Thisguarantees tightly controlled load sharingamong rectifiers, and providing status andidentification information to the controller.

At only two rack units high, these compactrectifiers provide up to 1350W and fit up tofive rectifier modules in a 23in. rack or fourmodules in a 19in. rack. Designed withdiversity in mind, the Xscend rectifier is ableto operate in a complete range of indoor andoutdoor applications.

Features• Compact 2 rack unit height• Front or mid-mountable• 208/240 single phase input• Hot-swappable • No adjustments required• 90% typical efficiency• Active and droop current sharing• International Standards Compliance

Xscend PowerSystem

XR1448Rectifier Module

www.power-one.com

InputModel XR1448

Input Voltage 180-264VAC (47-63Hz)

Current (max.) 9.3A @180VAC

Inrush Current 25A @ 25°C

Power Factor >0.98 typical

Fuse 12.5A- line, 12.5A- neutral

Connection FCI power connector™

EMC EN 61000-6-2, EN 61000-6-3, FCC Part 15 Class B

OutputModel XR1448

Output Voltage 42-58VDC

Power (max.) 1350W

Current 25A


Tolerance Vout +/- 1.0%, constantvoltage regulation

TransientResponse +/- 4% recovery time 2ms

Load Sharing +/- 5%

Ripple

DescriptionThe Power-One Xscend™ Controller System (XCS) provides comprehensive monitoringand control for Power-One’s Xscend DC power systems. This digital controller monitorstotal system conditions including DC voltage, rectifier current, rectifier temperature,system capacity, battery parameters and circuit breaker status.

The XCS enables data storage of system configuration information such as battery type,installation date and system commission date. Visual notification of alarm and warningconditions are indicated by front panel LEDs, while descriptions of the alarms are providedthrough an LCD, or as an option, may be accessed remotely through a modem or aNetwork Interface (PNI) module.

To meet individual site requirements, the XCS contains a logic operator that can beprogrammed to monitor and control specified requirements. This allows actions to be set,alarms to be triggered, and outputs to be activated based on internal and external signalmonitoring, comparing and processing.






• Multiple language options


XCSController

www.power-one.com







• Monthly data logging


Current


Input

Output

Mechanical

Components

Model Compac 48V Compac 24V

Input Voltage 180 - 264 VAC, 50-60 HzSingle or three-phase180 - 264 VAC, 50-60 HzSingle or three-phase

Current (at full load) 15A per rectifier at full load 15A per rectifier at full load

Input Breaker Rating 40A per rectifier 40A per rectifier

Input Wire Size 8 AWG (max.) 8 AWG (max.)

DC Bus Rating 800 or 1200A options 800 or 1200A options

Output Current 50-1200A 100-800A

Efficiency >86% >86%

Current Rating per BreakerPanel (max.) 400A 400A

Controller DMAC Controller DMAC Controller

Rectifier NHS48/50 NHS24/100

Width 19 or 23in.

Battery Tray Depth 21, 25 or 29in.

Mounting (base) Mounting holes provided

Altitude Range 13,000 ft., derate 7°C/1000ft. above 8,000 ft.

Operating Temperature -0 to +50°C

Storage Temperature -50 to +85°C

Temperature Coefficient +/- 0.0008%/°C from 0-50°C, after one hour warm up

Humidity 10-90% RH, operating, 5-95% storage, non-condensing

Heat Dissipation per Rectifier 1,255 BTU’s per hour at full load

DescriptionCompac Racks are modular power systemsdesigned for applications requiring 50 to 1200 amps.An almost limitless combination of rectifiers, breakerpanels, and battery shelves are available. Stand-alone configurations with up to 750 Ah of batterybackup are available. Each rack can hold up to 24rectifiers or a maximum of five battery trays.Systems can be ordered with ultimate capacity forfuture additions of rectifiers and batteries.

Standard features include timer-controlled equalizeand battery test functions, current and voltagedisplay meters, LED’s for local alarm indications,user-programmable alarm set inputs, and a set ofform “C” alarm contacts for remote monitoring.Optional features include low voltage disconnect,complete battery systems, and battery temperaturecompensation.

The Compac systems distribution architecture can bedesigned for load shedding during power outages,allowing critical loads to stay up longer on batterypower by eliminating non-critical equipment loadsearlier in the discharge cycle.

Features• Modular systems from 50-1200A• 24V or 48V outputs• 180-264 VAC single or three-phase inputs• Rack widths of 19in. or 23in.• Hot-swappable rectifiers• Small footprint• Scalable N+1 redundancy with current sharing

Low Voltage Disconnect (LVD)

Power System

Compac Rack System™Power System

www.power-one.comwww.power-one.com11V0005-047 CMPSYS V3.0

Compac Rack System™

Contactor Rating 800-1200A options 800-1200A options

Disconnect Voltage(User Adjustable)

42V 21V

LVD Disconnect Range 31 - 51V 18 - 26V

Reconnect Voltage 6.5V above disconnectvoltage4.7V above disconnectvoltage

• Power factor correction (PFC)• Extensive monitoring capabilities• Options include integrated battery systems and extensive

breaker and fuse layouts• A single seven foot rack can provide distribution, 400A of

rectifiers, and 750Ah of batteries• International standards compliance

The Compac Power System is available in three different configurations, allowing customers to choosethe solution that is right for them. Each system uses the same basic components, systems include:

Breaker Panels• Twenty positions for 5 to 100A

breakers• Two positions for 125 to 250A

breakers• A single position for a 450A or 525A

breaker

Low Voltage Disconnect• Optional Feature• Provides protection against deep

discharge of batteries• Emergency Power Off (EPO) switch

provided for emergency shutoff• Remote contacts for EPO

Rectifier Shelves• Interfaces with controller• 23” shelf allows up to 4

rectifiers each• Active current sharing• Single or three-phase input

DMAC Controller• Single point system voltage adjust• Programmable timer for battery test

or equalization

• Digital meters and test points monitor plant voltages and current

• User-adjustable set points for under/over voltage and low voltage disconnect

NHS Rectifiers• 4 Rectifiers into each 3U 23” shelf • Available in 24 or 48VDC• Thermal protection• Fan cooled modules • Hot swappable• Low weight• High reliability

System ConfigurationsSystem Components


Temperature Compensation• Works in conjunction with the DMAC

controller• Automatically adjusts the float

voltage according to the ambient temperature

• Sets off alarms when battery thermal runaway or sensor failure is indicated

48VDC 1200A SystemThe Compac full rack systemallows for up to 1200A at 48V in asingle bay by using combinationsof distribution options. Eachrack is capable of holding up tosix rectifier shelves, a DMACcontroller panel, variousdistribution options and rearconnection points for externalbattery strings.

48VDC 400A SystemThe Compac full rack systemwith battery shelves allows for upto 400A at 48V in a single bay.Each rack is capable of holdingup to five battery trays for 100 to150 Ah battery reserve strings.

24VDC 800A SystemThe Compac full rack systemwithout battery shelves allows forup to 800A at 24V in a single bay.Each rack is open at the bottomto allow room for user installedequipment.


Input

Output

Mechanical

Components

Model Compac 48V Compac 24V

Input Voltage 180 - 264 VAC, 50-60 HzSingle or three-phase180 - 264 VAC, 50-60 HzSingle or three-phase

Current (at full load) 15A per rectifier at full load 15A per rectifier at full load

Input Breaker Rating 40A per rectifier 40A per rectifier

Input Wire Size 8 AWG (max.) 8 AWG (max.)

DC Bus Rating 800 or 1200A options 800 or 1200A options

Output Current 50-1200A 100-800A


Current Rating per BreakerPanel (max.) 400A 400A

Controller DMAC Controller DMAC Controller

Rectifier NHS48/50 NHS24/100

Width 19 or 23in.

Battery Tray Depth 21, 25 or 29in.

Mounting (base) Mounting holes provided

Altitude Range 13,000 ft., derate 7°C/1000ft. above 8,000 ft.

Operating Temperature -0 to +50°C

Storage Temperature -50 to +85°C

Temperature Coefficient +/- 0.0008%/°C from 0-50°C, after one hour warm up

Humidity 10-90% RH, operating, 5-95% storage, non-condensing

Heat Dissipation per Rectifier 1,255 BTU’s per hour at full load

DescriptionCompac Racks are modular power systemsdesigned for applications requiring 50 to 1200 amps.An almost limitless combination of rectifiers, breakerpanels, and battery shelves are available. Stand-alone configurations with up to 750 Ah of batterybackup are available. Each rack can hold up to 24rectifiers or a maximum of five battery trays.Systems can be ordered with ultimate capacity forfuture additions of rectifiers and batteries.

Standard features include timer-controlled equalizeand battery test functions, current and voltagedisplay meters, LED’s for local alarm indications,user-programmable alarm set inputs, and a set ofform “C” alarm contacts for remote monitoring.Optional features include low voltage disconnect,complete battery systems, and battery temperaturecompensation.

The Compac systems distribution architecture can bedesigned for load shedding during power outages,allowing critical loads to stay up longer on batterypower by eliminating non-critical equipment loadsearlier in the discharge cycle.

Features• Modular systems from 50-1200A• 24V or 48V outputs• 180-264 VAC single or three-phase inputs• Rack widths of 19in. or 23in.• Hot-swappable rectifiers• Small footprint• Scalable N+1 redundancy with current sharing

Low Voltage Disconnect (LVD)

Power System


www.power-one.comwww.power-one.com11V0005-047 CMPSYS V3.0

Compac Rack System™

Contactor Rating 800-1200A options 800-1200A options

Disconnect Voltage(User Adjustable)

42V 21V

LVD Disconnect Range 31 - 51V 18 - 26V

Reconnect Voltage 6.5V above disconnectvoltage4.7V above disconnectvoltage

• Power factor correction (PFC)• Extensive monitoring capabilities• Options include integrated battery systems and extensive

breaker and fuse layouts• A single seven foot rack can provide distribution, 400A of

rectifiers, and 750Ah of batteries• International standards compliance

DescriptionThe Power-One NHS rectifier modulesprovide extremely reliable DC poweroutput for use in our Compac™ series ofpower systems. NHS rectifier modulesare hot-swappable and provide a completeset of interface signals.

At only 3 rack units high, these compactrectifiers allow for up to four modules ineach 23in. rack and provide up to 50A at48V or up to 100A at 24V. With full poweravailable up to 50°C, these rectifiers areideal for any indoor and outdoorapplications.

Features• Compact 3 rack-unit height• 24V and 48V rectifiers• 50A output at 48V• 100A output at 24V• 180-264 single or three phase inputs• Hot-Swappable, plug-and-play rectifiers• High power density (9.8W/in3)• High reliability, >700,000 hours MTBF• Power factor correction• Active current sharing• International Standards Compliance

NHSRectifier Module

www.power-one.com

InputModel NHS24/100 NHS48/50

InputVoltage 180 - 264V AC single phase, (50-60Hz)

Current 15A @ 230V 15A @ 230V

Soft Start 0.99 (50-100% load)

ACTransient 3000V, 2 Joules

Output

MechanicalDimensions 5 x 5 x 12.25 in. (12.7 x 12.7 x 31.1cm )

Weight 12.6 lbs.

Cooling Fan

Other Technical Data

Model NHS24/100 NHS48/50

Power (max.) 2400W 2400W

OutputVoltage 25-29V DC 51-59V DC

Current (max.) 100A 50A

Efficiency(@ 40-90%Load)*

>86% >86%

VoltageRegulation +/- 0.4%

TransientResponse

+/- 4% at load variation 10-90% or 90-10%, recovery time 10ms

Load Sharing

Features• Single point system voltage adjust• Programmable timer for battery test or

equalization• Digital meters and test points monitor plant

voltages and current• User-adjustable set points for under/over voltage

and low voltage disconnect

DMACController

DescriptionThe Power-One Digital Meter, Alarm and Control Panel (DMAC) provides comprehensivemonitoring and control for Power-One’s Compac™ power systems. This digital controllermonitors system conditions including DC voltage and load current, while providing avariety of alarm and control functions.

DMAC features include user-configurable battery testing, measurement of battery voltageand current & battery equalization.

Front panel LED’s for alarms, including:• Equalize alarm• OV/UV alarm• Major alarm• Minor alarm• Rectifier fail• Breaker alarm

www.power-one.com

Temperature Compensation

Other Technical DataOperatingTemperature -0 to +50°C


Humidity 10-90% RH, operating, 5-95%storage, non-condensing

AltitudeRange

13,000 ft., derate 7°C/100 ft.above 8000 ft.

Overview

The temperaturecompensation panel works inconjunction with the DMACcontroller. Temperaturecompensation automaticallyadjusts the float voltageaccording to the ambienttemperature.

TemperatureCompensationAlarms

Alarms include temperaturedelta, which indicates batterythermal runaway and sensorfailure. In the event of asensor or panel failure, thecompensation defaults to thenormal float voltage set by thecontroller.

Interface


Display Digital amp and digital volt meters

Digital Meters 3.5 digits, +/-2% accuracy

UV/OVAdjustment

22V/29V for 24VDC +/- 1.5V 44V/58V for 48VDC +/- 1.5V

Equalization &Battery TestTimer Range

0.5 seconds to 130 hours

CurrentMeasurementDC Shunt

1200A:50mA

User Controls

Timer reset buttonSystem voltage adjustmentNormal/Bypass test switchEqualize/Battery test switchEqualize Under/Over voltage adjustmentUndervoltage/Overvoltage

ConnectionPoints

System voltage test pointsSystem amperage test points

www.power-one.com11V0005-050 DMAC V3.0

DMACController

Alarms

Alarms

Equalize alarmOV/UV alarmMajor alarmMinor alarmRectifier failBreaker alarm


Input

Output

Mechanical

Components

Model Integrity-One 48V Integrity-One 24V

Input 176 < Vin < 275V 176 < Vin < 275V

Inputs Single or individual Single or individual

Current (at full load) 16A per rectifier (max.) 16A per rectifier (max.)

Fuse 25A per rectifier 25A per rectifier

Rectifier Modules 50-1250A 110-1100A

Voltage 50-1250A 110-1100A


Controller PCS Controller PCS Controller

Rectifier PMP 25.48 PMP 25.24

Dimensions (WxHxD) 23 x 84 x 23 in.(584 x 2133 x 584mm)23 x 46 x 23 in.(584 x 1168 x 584mm)

Mounting (rack) 23” 23”

Mounting (base) Mounting holes provided Mounting holes provided

Audible Noise

The Integrity-One system is available in three different configurationsallowing customers to choose the solution that is right for them. Eachsystem uses the same basic components, including:

• System Interface Shelf• Alarm Output Connections• Network Interface (Optional)• Battery LVD (Optional)

• PCS Controller• PMP25 Rectifier Modules• SDS / PDS Distribution Shelves• Single or Individual Rectifier AC Inputs to Each Rectifier Shelf

Full Rack SystemThe Integrity-One full rack system allows for up to 1250A at 48V in asingle bay by using combinations of Secondary or PrimaryDistributions. Each rack is capable of holding up to five rectifiershelves for 48V applications providing 1250A or two rectifier shelves for24V applications providing 1100A. Multiple racks may be paralleled toproduce a maximum total system capability of 5000A using a singlecontroller in the primary rack.

Half-Height Rack SystemThe Integrity-One Half-Height rack system is available at up to 1100Aand can be installed above existing battery stands. The Half-Heightsystem is ideal for systems requiring extended battery backup. Up to44 load breakers can distribute up to 500A at -48V, or up to 1000A at+24V.

Integrity-One Rack with Battery TraysThe Integrity-One System with battery trays accommodates up to tworectifier shelves and up to three battery trays creating a complete powersystem in a single rack. Distribution can be achieved through up to 44load breakers or fuses (up to 100A rating).

Integrity-One FullRack System

Integrity-One Half-Height Rack System


Integrity-One™ Power SystemRack System

Distribution Panels• Hot-swappable distribution shelves• Front, middle and rear distribution

positions (waterfall effect) allow for system cable management

• SDS: Secondary Distribution Shelf• Rated at 500A• Plug in CB’s up to 100A rating• Plug in fuses up to 100A rating• Accommodates up to 22 circuit

breakers or fuses

• PDS: Primary Distribution Shelf (rated at 1000A)• Up to qty 8 single pole fuses

(100-600A)• Up to qty 8 single pole CB’s

(up to 250A rating)• Up to qty 3 double pole CB’s

(up to 400A rating)• Up to qty 2 triple pole CB’s

(up to 600A rating)

System Interface Shelf• Easy connection of system alarm

signals and wiring• Optional battery symmetry and

temperature probes• Optional Power-One Network Interface

box (featuring ethernet and SMNPprotocol capability)

• Optional low voltage disconnect• Battery shunt

Rectifier Shelves• RS485 communication bus• 23” shelf allows up to 5

rectifiers each• Digital current sharing• Individual rectifier or single

shelf AC feed options

PCS Controller• RS485 digital signal data bus • Fully programmable• 6 programmable alarms

(upgradeable to 24)• Battery test: manual or

automatic• Alarm relay test• Adjustable battery current• Software controlled start-up

after mains outage

PMP25 Rectifier• 5 rectifiers into each 4U 23” shelf • Available in 24 or 48VDC• Thermal protection• Fan cooled modules with speed

control and alarms• Hot-swappable• RS485 interface• Low weight• Up to 91% efficiency

Integrity Shown withOptional AC Distribution

Box


Input

Output

Mechanical

Components

Model Integrity-One 48V Integrity-One 24V

Input 176 < Vin < 275V 176 < Vin < 275V

Inputs Single or individual Single or individual

Current (at full load) 16A per rectifier (max.) 16A per rectifier (max.)

Fuse 25A per rectifier 25A per rectifier

Rectifier Modules 50-1250A 110-1100A

Voltage 50-1250A 110-1100A


Controller PCS Controller PCS Controller

Rectifier PMP 25.48 PMP 25.24

Dimensions (WxHxD) 23 x 84 x 23 in.(584 x 2133 x 584mm)23 x 46 x 23 in.(584 x 1168 x 584mm)

Mounting (rack) 23” 23”

Mounting (base) Mounting holes provided Mounting holes provided

Audible Noise

DescriptionThe Power-One PMP 25 rectifier providesextremely reliable DC power in a compactmodule. Digital interfaces areincorporated using an RS485 data bus tocommunicate with the system controllerand adjacent rectifiers guaranteeingtightly controlled load sharing amongrectifiers, and providing status andidentification information to the controller.

At only 4 rack units high, these compactrectifiers allow for up to five modules ineach 23in. rack (4 units in 19in. rack)providing up to 250A at 48V or up to 550Aat 24V. With full power available up to65°C, these rectifiers are ideal for bothindoor and outdoor applications.

Features• Compact 4 rack-unit height• 24V and 48V rectifiers• 50A output at 48V• 110A output at 24V• 208 / 240 single phase input• Hot-swappable rectifiers• No adjustment required• High efficiency, up to 91%• Active current sharing• International standards compliance

Integrity-One™ FullHeight System


www.power-one.com

InputModel PMP 25.24 PMP 25.48

InputVoltage

196 - 250V AC ±10% single phase, (44-66Hz)176-160V AC at reduced output power

Current(max.)






• Multiple language options


PCSController

DescriptionThe Power-One Power Controller System (PCS) provides comprehensive monitoring and control fora broad range of Power-One’s DC power systems. This digital controller monitors total systemconditions including DC voltage, rectifier current, rectifier temperature, system capacity, batteryparameters and circuit breaker status.

The PCS enables data storage of system configuration information such as battery type, installationdate and system commission date. In addition, the PCS is capable of monitoring up to 128 rectifiersand 128 sub-controllers within a power system. Visual notification of alarm and warning conditionsare indicated by front panel LEDs, while descriptions of the alarms are provided through an LCD oras an option may be accessed remotely through a modem or a Network Interface (PNI) module.

To meet individual site requirements, the PCS contains a logic operator that can be programmed tomonitor and control specified requirements. This allows actions to be set, alarms to be triggered, andoutputs to be activated based on internal and external signal monitoring, comparing and processing.







• Monthly data logging

www.power-one.com

Input

Voltage 18-72V DC

Current

Date post:	24-Jan-2021
Category:	Documents
Upload:	others
View:	1 times
Download:	0 times

Power System PPS 7 - Steven Engineering · 2004. 3. 24. · Rectifier Features Model Voltage Power...

Documents