POWER TOOL SOLUTIONSTM FOR VEHICLE SERVICES
POWER TOOL SOLUTIONSTM
Eagle Group is a leading supplier of power tools for industrial markets. Whether you need tools for material removal, finishing, maintenance, automotive, or assembly — Eagle Group has your solution.
Eagle Group has been a supplier of power tools for over 30 years throughout the United States, Mexico and South America.
Located in Portland, Oregon, Eagle resides in AIMCO’s corporate complex.
CALL TODAY TOLL FREE: 1-877-273-3903
Abrasive Tools
Drills
Percussion Tools
Cutting Tools
Accessories
Impact Wrenches
Fastening Tools
TABLE OF CONTENTS
3
Impact Wrenches . . . . . . . . . . . . . . 4
Clutch Selection Information Chart 3/8" 1/2" 3/4" 1" 1 1/2"
Accessories . . . . . . . . . . . . . . . . . . 13
Torque Wrenches Balancers Retractors FRL Lubricators Regulators Hoses Air Fittings Couplers Bits and Sockets Mag-O-Nets®
www.eagle-premier.com44
Single Hammer
Twin Hammer
Pin Clutch
ClutchInformationChart
TOOL TYPE: USES:
24501" Impact WrenchPage 28
Swing Hammer Clutch
l Standard assembly lAutomotive repairl Light industrial use
l Industrial maintenance lTire service
l Maintenance l Light assembly l Hard joints
l Delivers high torque-to-weight ratio.
l Reliable system producing torque quickly with two forged hammers.
l Rapid delivery of torque. l High power-to-weight ratio.
IMPACT WRENCH TYPES
l Rapid delivery of torque. l Simple, effective design.
l Standard assembly applications
l Maintenance l Hard joints
www.eagle-premier.com 5
IMPACT WRENCHES
www.eagle-premier.com 5
20103/8" Butterfly InlineImpact Wrench
Specifications:
GENERAL DUTY
l Approximate Working Torque - 75 ft-lb
lSingle hammer design.
lAir inlet swivels 360o for easy maneuvering.
lFor bench work, carburetors, ignitions, body panels, transmissions, fender struts, oil pans, and small engine work.
lButterfly throttle allows one hand directional changes.
Drive Size: ................................. 3/8"RPM - Approximate: ................. 10,000Torque Range - Approximate: ... 11- 75 ft-lb / 15 -102 NmMax Torque: .............................. 92 ft-lb / 125 NmWeight: ...................................... 2.8 lb / 1.3 kgLength: ...................................... 6.4 in / 163 mmAir Usage: .................................. 13 cfmAir Inlet: .................................... 1/4"
51052163EC3/8" Impact Wrench
Specifications:
l Approximate Working Torque - 189 ft-lb
lComposite housing.
lTwin hammer design.
lSwivel air inlet fitting.
lLarge easy-to-use forward reverse switch.
lBottom grease fitting.
Drive Size: ................................. 3/8"RPM - Approximate: ................. 10,400Torque Range - Approximate: ... 131 - 189 ft-lb / 178 - 256 NmMax Torque: .............................. 220 ft-lb / 298 NmWeight: ...................................... 2.7 lb / 1.2 kgLength: ...................................... 6.5 in / 165 mmAir Usage: .................................. 15 cfmAir Inlet: .................................... 1/4"
INDUSTRIAL DUTY
2120
Specifications:
3/8" Impact Wrench
l Approximate Working Torque - 292 ft-lb
lComposite and lightweight housing.
lTwin hammer design.
lSwivel air inlet fitting.
lUnique motor set design eliminates power loss.
lNoise reducing exhaust design for quiet operation.
Drive Size: ................................. 3/8"RPM - Approximate: ................. 8,000Torque Range - Approximate: ... 50 - 292 ft-lb / 70- 395 NmMax Torque: .............................. 300 ft-lb / 405 NmWeight: ...................................... 2.9 lb / 1.3 kgLength: ...................................... 6.5 in / 165 mmAir Usage: .................................. 15 cfmAir Inlet: .................................... 1/4"
INDUSTRIAL DUTY21503/8" Impact Wrench
INDUSTRIAL DUTY
Specifications:
l Approximate Working Torque - 145 ft-lb
lTwin hammer design
lSteel clutch housing protects hammer mechanism
lFast cycle times
lLong life
lFor general industrial use
Drive Size: ................................. 3/8"RPM - Approximate: ................. 10,000Torque Range - Approximate: ... 100 - 145 ft-lb / 136 - 197 NmMax Torque: .............................. 199 ft-lb / 270 NmWeight: ...................................... 3.3 lb / 1.5 kgLength: ...................................... 6.0 in / 152 mmAir Usage: .................................. 13 cfmAir Inlet: .................................... 1/4"
www.eagle-premier.com6
IMPACT WRENCHESIMPACT WRENCHES
Specifications:
1/2" Impact Wrench
GENERAL DUTY22252225L
lMetal housing for durability.
lTwin hammer design.
lCompact size for tight access.
lHandle exit exhaust.
l2225 with standard anvil.
l2225L with extended length anvil.
Drive Size: ................................. 1/2"RPM - Approximate: ................. 8,000Torque Range - Approximate: ... 190 - 328 ft-lb / 257- 445 NmMax Torque: .............................. 365 ft-lb / 495 NmWeight: ...................................... 5.6 lb / 2.5 kgLength: ...................................... 7.25 in / 184 mmAir Usage: .................................. 15 cfmAir Inlet: .................................... 1/4"
22561/2" Impact Wrench
Specifications:
l Twin hammer design.
l Handle exhaust directs air away.
l Steel Casing
Drive Size: ................................. 1/2"RPM - Approximate: ................. 7,000Torque Range - Approximate: ... 240 - 395 ft-lb / 325 - 535 NmMax Torque: .............................. 425 ft-lb / 575 NmWeight: ...................................... 5.8 lb / 2.6 kgLength: ...................................... 7.5 in / 190 mmAir Usage: .................................. 15 cfmAir Inlet: .................................... 1/4"
INDUSTRIAL DUTY
l Approximate Working Torque - 328 ft-lb
l Approximate Working Torque - 395 ft-lb
Specifications:
1/2" Impact Wrench
l Approximate Working Torque - 260 ft-lb
GENERAL DUTY22602260L
lEngineered for the after- market automotive industry.
lPin clutch design to quickly deliver torque.
l2260 with standard anvil
l2260L with 2-1/2" extended anvil
Drive Size: ................................. 1/2"RPM - Approximate: ................. 7,500Torque Range - Approximate: ... 114 - 260 ft-lb / 154 - 352 NmMax Torque: .............................. 302 ft-lb / 409 NmWeight: ...................................... 6.15 lb / 2.8 kgLength: ...................................... 7.5 in / 194 mmAir Usage: .................................. 12 cfmAir Inlet: .................................... 1/4"
2125PEC
Specifications:
1/2" Composite Impact Wrench, Pin Type AnvillComposite and lightweight housing.
lTwin hammer design.
lSwivel air inlet fitting.
lUnique motor set design eliminates power loss.
lNoise reducing exhaust design for quiet operation.
Drive Size: ................................. 1/2"RPM - Approximate: ................. 10,000Torque Range - Approximate: ... 50 - 292 ft-lb / 70- 395 NmMax Torque: .............................. 300 ft-lb / 405 NmWeight: ...................................... 2.9 lb / 1.3 kgLength: ...................................... 6.5 in / 165 mmAir Usage: .................................. 15 cfmAir Inlet: .................................... 1/4"
INDUSTRIAL DUTY
l Approximate Working Torque - 292 ft-lb
www.eagle-premier.com 7
IMPACT WRENCHESIMPACT WRENCHES
5105
2258EC1/2" CompositeImpact Wrench
Specifications:
lComposite housing.
lTwin hammer design.
lSwivel air inlet fitting.
lLarge easy-to-use forward reverse switch.
lSame as 2163EC with 1/2" square drive.
Drive Size: ................................. 1/2"RPM - Approximate: ................. 10,400Torque Range - Approximate: ... 131 - 189 ft-lb / 178 - 256 NmMax Torque: .............................. 220 ft-lb / 298 NmWeight: ...................................... 2.7 lb / 1.2 kgLength: ...................................... 6.5 in / 165 mmAir Usage: .................................. 15 cfmAir Inlet: .................................... 1/4"
INDUSTRIAL DUTY
2263EC1/2" CompositeImpact Wrench
Specifications:
lTwin hammer design.
lSwivel air inlet fitting.
lLarge easy-to-use forward reverse switch.
lBottom grease fitting.
Drive Size: ................................. 1/2"RPM - Approximate: ................. 7,800Torque Range - Approximate: ... 210 - 295 ft-lb / 284 - 400 NmMax Torque: .............................. 333 ft-lb / 452 NmWeight: ...................................... 4.5 lb / 2.0 kgLength: ...................................... 8.2 in / 208 mmAir Usage: .................................. 19 cfmAir Inlet: .................................... 1/4"
INDUSTRIAL DUTY
l Approximate Working Torque - 295 ft-lb
22402240PEC
Specifications:
1/2" CompositeImpact WrenchlComposite and lightweight housing.
lTwin hammer design.
lSwivel air inlet fitting.
lUnique motor set design eliminates power loss.
lNoise reducing exhaust design for quiet operation.
Drive Size: ................................. 1/2"RPM - Approximate: ................. 8,000Torque Range - Approximate: ... 100 - 410 ft-lb / 135- 550 NmMax Torque: .............................. 450 ft-lb / 600 NmWeight: ...................................... 4.9 lb / 2.3 kgLength: ...................................... 8.3 in / 208 mmAir Usage: .................................. 18 cfmAir Inlet: .................................... 1/4"
2240PECPinned Anvil
INDUSTRIAL DUTY
l Approximate Working Torque - 410 ft-lb l Approximate Working Torque - 189 ft-lb
23773/4" Impact Wrench
Specifications:
l Approximate Working Torque - 1,065 ft-lb
lComposite housing.
lTwin hammer design.
lHandle exhaust directs air away.
lFeathering trigger for ultimate control.
Drive Size: ................................. 3/4"RPM - Approximate: ................. 5,000Torque Range - Approximate: ... 230- 1,065 ft-lb / 310- 1,450 NmMax Torque: .............................. 1,250 ft-lb / 1, 695 NmWeight: ...................................... 8.05 lb / 3.6 kgLength: ...................................... 8.75 in / 222 mmAir Usage: .................................. 19 cfmAir Inlet: .................................... 1/2"
INDUSTRIAL DUTY
www.eagle-premier.com8
IMPACT WRENCHES
5105
51052375EC3/4" Composite Impact Wrench
Specifications:
l Approximate Working Torque - 1,290 ft-lb
lComposite housing.
lTwin hammer design.
lSwivel air inlet fitting.
lLarge easy-to-use forward reverse switch.
lBottom grease fitting.
Drive Size: ................................. 3/4"RPM - Approximate: ................. 5,500Torque Range - Approximate: ... 915 - 1,290 ft-lb / 1,243 - 1,750 NmMax Torque: .............................. 1,540 ft-lb / 2, 090 NmWeight: ...................................... 7.8 lb / 3.5 kgLength: ...................................... 9.4 in / 239 mmAir Usage: .................................. 27 cfmAir Inlet: .................................... 3/8"
INDUSTRIAL DUTY
5105
23803/4" Composite Impact Wrench
Specifications:
l Approximate Working Torque - 1,450 ft-lb
lCompact composite housing.
lSwing hammer design.
lOptimal power-to-weight ratio.
lMost powerful tool in its class.
lHandle exhaust directs air away.
Drive Size: ................................. 3/4"RPM - Approximate: ................. 4,000Torque Range - Approximate: ... 125 - 1,450 ft-lb / 170- 1,975 NmMax Torque: .............................. 1,875 ft-lb / 2, 540 NmWeight: ...................................... 12.4 lb / 5.6 kgLength: ...................................... 11.75 in / 298 mmAir Usage: .................................. 19.4 cfmAir Inlet: .................................... 1/2"
INDUSTRIAL DUTY
20043/4" Impact Wrench
Specifications:
l Approximate Working Torque - 550 ft-lb
GENERAL DUTY
lSingle hammer design.
lBuilt-in regulator.
lAvailable with extended anvil.
Drive Size: ................................. 3/4"RPM - Approximate: ................. 5,000Torque Range - Approximate: ... 145 - 500 ft-lb / 196 - 746 NmMax Torque: .............................. 600 ft-lb / 815 NmWeight: ...................................... 10.5 lb / 4.8 kgLength: ...................................... 9.5 in / 241 mmAir Usage: .................................. 28 cfmAir Inlet: .................................... 3/8"
24801" Composite Impact Wrench
Specifications:
l Approximate Working Torque - 1,450 ft-lb
lCompact, composite housing.
lSwing hammer design.
lOptimal power-to-weight ratio.
lMost powerful tool in its class.
lHandle exhaust directs air away.
Drive Size: ................................. 1"RPM - Approximate: ................. 4,000Torque Range - Approximate: ... 125 - 1,450 ft-lb / 170- 1,975 NmMax Torque: .............................. 1,875 ft-lb / 2, 540 NmWeight: ...................................... 12.4 lb / 5.6 kgLength: ...................................... 11.75 in / 298 mmAir Usage: .................................. 19.4 cfmAir Inlet: .................................... 1/2"
INDUSTRIAL DUTY
www.eagle-premier.com 9
IMPACT WRENCHES
2485L1" Inline Impact Wrench, Extended
Specifications:
l Approximate Working Torque - 1,875 ft-lb
INDUSTRIAL DUTY
lSwing hammer clutch design for low vibration.
lExtended anvil for optimal access on deep wheels and applications.
Drive Size: ................................. 1"RPM - Approximate: ................. 4,000Torque Range - Approximate: ... 833 - 1,875 ft-lb / 1,130- 2,542 NmMax Torque: .............................. 2,290 ft-lb / 3,100 NmWeight: ...................................... 28 lb / 12.7 kgLength: ...................................... 19 in / 482 mmAir Usage: .................................. 30 cfm Air Inlet: .................................... 1/2"
24631" Impact WrenchExtended
l Approximate Working Torque - 1,300 ft-lb
INDUSTRIAL DUTY
lTwin hammer design.
lSteel clutch housing protects hammer mechanism.
lFor tire changing on trucks and buses.
Drive Size: ................................. 1"RPM - Approximate: ................. 3,900Torque Range - Approximate: ... 670 - 1,300 ft-lb / 908 - 1,760 NmMax Torque: .............................. 1,600 ft-lb / 2,169 NmWeight: ...................................... 20.2 lb / 9.0 kgLength: ...................................... 22.0 in / 559 mmAir Usage: .................................. 26 cfmAir Inlet: .................................... 1/2"
2403L1" Inline ImpactWrench, Extended
Specifications:
l Approximate Working Torque - 1,875 ft-lb
INDUSTRIAL DUTY
lComposite housing reduces weight.
lExtended Anvil.
lTwin hammer design.
lSwivel exhaust.
Drive Size: ................................. 1"RPM - Approximate: ................. 4,000Torque Range - Approximate: ... 1,250 - 1,875 ft-lb / 1,695- 2,550 NmMax Torque: .............................. 2,000 ft-lb / 2,825 NmWeight: ...................................... 21.3 lb / 9.7 kgLength: ...................................... 23 in / 584 mmAir Usage: .................................. 25 cfm Air Inlet: .................................... 1/2"
Specifications:
1" Inline Impact Wrench
Specifications:
l Approximate Working Torque - 1,450 ft-lb
INDUSTRIAL DUTY24502450L
lTwin hammer design.
lSmooth power in a compact, lightweight design.
l2450 with standard 3" anvil.
l2450L with 6" extended anvil.
Drive Size: ................................. 1" RPM - Approximate: ................. 6,000Torque Range - Approximate: ... 940 - 1,450 ft-lb / 1,274 - 1,965 NmMax Torque: .............................. 1,600 ft-lb / 2,169 NmWeight: ...................................... 19 lb / 8.5 kgLength: ...................................... 19.5 in / 495 mmAir Usage: .................................. 26 cfmAir Inlet: .................................... 1/2"
www.eagle-premier.com10
IMPACT WRENCHES
5105 51052453
Specifications:
1" Impact Wrench
l Approximate Working Torque - 1,300 ft-lb
INDUSTRIAL DUTY
lTwin hammer design.
lSteel clutch housing protects hammer mechanism.
lFor off-road equipment repair, heavy equipment, MRO.
Drive Size: ................................. 1"RPM - Approximate: ................. 3,900Torque Range - Approximate: ... 670 - 1,300 ft-lb / 908 - 1,760 NmMax Torque: .............................. 1,600 ft-lb / 2,170 NmWeight: ...................................... 20.3 lb / 9.2 kgLength: ...................................... 15.3 in / 388 mmAir Usage: .................................. 26 cfmAir Inlet: .................................... 1/2"
25501 1/2" InlineImpact Wrench
Specifications:
l Approximate Working Torque - 3,200 ft-lb
INDUSTRIAL DUTY
lEfficient power to weight ratio.
lSwing hammer clutch.
Drive Size: ................................. 1 1/2" RPM - Approximate: ................. 2,500Torque Range - Approximate: ... 2,100 - 3,200 ft-lb / 2,847 - 4,338 NmMax Torque: .............................. 3,500 ft-lb /4,745 NmWeight: ...................................... 50 lb / 23 kgLength: ...................................... 20 in / 508 mmAir Usage: .................................. 75 cfmAir Inlet: .................................... 1/2"
www.eagle-premier.com 11
RATCHET WRENCHES
510531151/4" Ratchet Wrench
Specifications:
31003/8" Ratchet Wrench
Specifications:
3105
Specifications:
1/2" Ratchet Wrench
GENERAL DUTY
GENERAL DUTY
l Approximate Working Torque - 18 ft-lb l Approximate Working Torque - 24 ft-lb
l Approximate Working Torque - 55 ft-lb
lRear exhaust with silencer.
lExtended ratchet housing for greater reach.
lFor smaller fasteners.
Drive Size: ................................. 1/4"RPM - Approximate: ................. 230Torque - Approximate: ............. 18 ft-lb / 24 NmWeight: ...................................... 1.4 lb / 0.6 kgLength: ...................................... 8.0 in / 203 mmAir Usage: .................................. 10 cfmAir Inlet: .................................... 1/4"
lBall & needle bearing construction for long life.
lInternal ring gear with three planetary gears.
Drive Size: ................................. 3/8"RPM - Approximate: ................. 160Torque - Approximate: ............. 24 ft-lb / 33 NmWeight: ...................................... 2.6 lb / 1.2 kgLength: ...................................... 10.5 in / 267 mmAir Usage: .................................. 16 cfmAir Inlet: .................................... 1/4"
lExcellent for general purpose use.
lImproved gear head extends life.
lPower for tough jobs.
Drive Size: .................................. 1/2"RPM - Approximate: .................. 150Torque - Approximate: ............. 55 ft-lb / 74 NmWeight: ...................................... 3.1 lb / 1.4 kgLength: ....................................... 14.5 in / 368 mmAir Usage: .................................. 21 cfmAir Inlet: ..................................... 1/4"
32053/8" Ratchet Wrench
Specifications:
GENERAL DUTY
GENERAL DUTY
l Approximate Working Torque - 30 ft-lb
lComposite grip for increased operator comfort.
lBuilt-in grease fitting for lubrication ease.
Drive Size: ................................. 3/8"RPM - Approximate: ................. 160Torque - Approximate: ............. 30 ft-lb / 40 NmWeight: ...................................... 2.5 lb / 1.1 kgLength: ...................................... 10.5 in / 267 mmAir Usage: .................................. 18 cfmAir Inlet: .................................... 1/4"
www.eagle-premier.com12
l Approximate Working Torque - 80 ft-lb
RATCHET WRENCHES
510531201/4" Ratchet Wrench
Specifications:
3320
Specifications:
1/2" Ratchet Wrench
INDUSTRIAL DUTY
INDUSTRIAL DUTY
l Approximate Working Torque - 20 ft-lb
l Approximate Working Torque - 80 ft-lb
lRear exhaust with silencer.
lFor smaller fasteners.
lPatented head design for increased durability.
Drive Size: ................................. 1/4"RPM - Approximate: ................. 250Torque - Approximate: ............. 20 ft-lb / 27 NmWeight: ...................................... 1.5 lb / 0.7 kgLength: ...................................... 8.1 in / 205 mmAir Usage: .................................. 2.8 cfmAir Inlet: .................................... 1/4"
lExcellent for general purpose use.
lImproved gear head extends life.
lPower for tough jobs.
lPatented head design for increased durability.
Drive Size: .................................. 1/2"RPM - Approximate: .................. 280Torque - Approximate: ............. 80 ft-lb / 108.8 NmWeight: ...................................... 2.7 lb / 1.2 kgLength: ....................................... 10.9 in / 277 mmAir Usage: .................................. 4 cfmAir Inlet: ..................................... 1/4"
32203/8" Ratchet Wrench
Specifications:
INDUSTRIAL DUTY
l Approximate Working Torque - 80 ft-lb
lComposite grip for increased operator comfort.
lBuilt-in grease fitting for lubrication ease.
lPatented head design for increased durability.
Drive Size: ................................. 3/8"RPM - Approximate: ................. 280Torque - Approximate: ............. 80 ft-lb / 108.8 NmWeight: ...................................... 2.7 lb / 1.2 kgLength: ...................................... 10.9 in / 277 mmAir Usage: .................................. 4 cfmAir Inlet: .................................... 1/4"
www.eagle-premier.com 13
ACCESSORIES
5105TORQUE WRENCHES
CWR SERIESCLICK WRENCH
DW Series
lAccuracy is ±3% of indicated reading.
lBi-directional use for clockwise and counter clockwise auditing.
lLight weight tool design and ergonomic grip ensure operator comfort.
lLarge dial face allows quick and easy reference.
lOverall length of tool is designed for comfort. Operator can apply torque without undue strain.
lPrevents cosmetic damage to parts. Edges of wrench are covered in soft rubber.
lFits standard sockets with ¼" - ½" square drive sizes.
lFor metric series add "A" at the end of model number.
CWR Series
lAccuracy is ±3% of indicated reading.
lLight weight tool with streamlined design. Operator can apply torque without undue strain due to overall length of tool.
lFits standard sockets with ¼" - ½" square drive sizes.
lRepeatable and detectable action.
lMicrometer adjustable.
lFor Metric Series add "A" at the end of model number.
DW SERIESDIAL INDICATING
Part # Torque Range Square Drive
DW-75 0 - 75 in-lb 1/4"
DW-300 0 - 300 in-lb 3/8"
DW-175F 0 - 175 ft-lb 1/2"
Part # Torque Range Square Drive
CWR -100 40 - 100 in-lb 1/4"
CWR -200 50 - 200 in-lb 1/4"
CWR-250F 30 - 250 ft-lb 3/4"
www.eagle-premier.com14
ACCESSORIES
5105RETRACTORS
5105GRAVITY-DEFYING BALANCERS
ASB-0CTW SERIES
RPA SERIESRMA-L SERIES
lBuilt in Safety Features: Cable, drum, and containerized spring are fully visible without opening the unit for easy safety checks.
lErgonomic Spring Release: Automatic safety lock provides extra control.
lExtended Cable Length: Stainless steel cables allow for extended reach on applications.
lEnhanced Gear Mechanism: Allows for more exact adjustment of tension.
lNo Recoil and Low Resistance: Tapered drum style provides gravity defying tool positioning and travel.
RPA Series
lNo tools needed for setting of tension.
lFive foot nylon coated steel cable.
lReinforced hanging bracket includes provision for safety cable.
lAdjustable cable stop.
lTool clip included.
RMA-L Series
lExternal tension adjustment.
lRatchet cable lock.
lSteel housing with polyester finish.
lReinforced hanging bracket includes provision for safety cable.
lEight foot x 3/32" coated steel cable.
lTool clip included.
Part # Approximate Capacity StrokeASB-0C 1.1 - 3.3 lb 0.5 - 1.5 kg 51.1" 130 cm
ASB-3C 3.3 - 6.6 lb 1.5 - 3 kg 86.4" 220 cm
ASB-5C 5.5 - 11 lb 2.5 - 5 kg 86.4" 220 cm
Part # Approximate Capacity StrokeTW-00 1.1 - 3.3 lb 0.5 - 1.5 kg 18" 45.7 cm
TW-0 1.1 - 3.3 lb 0.5 - 1.5 kg 3.3' 100 cm
TW-3 2.2 - 6.6 lb 1.0 - 3 kg 4.3' 131 cm
TW-5 5.5 - 11 lb 2.5 - 5 kg 4.3' 131 cm
TW-9 10 - 20 lb 4.5 - 9 kg 4.3' 131 cm
TW-15 20 - 33 lb 9 - 15 kg 4.3' 131 cm
TW-22 33 - 48 lb 9 - 22 kg 5' 152 cm
TW-30 48 - 66 lb 22 - 30 kg 5' 152 cm
TW-40 66 - 88 lb 30 - 40 kg 5' 152 cm
TW-50 88 - 110 lb 40 - 50 kg 5' 152 cm
TW-60 110 - 132 lb 50 - 60 kg 5' 152 cm
TW-70 132 - 154 lb 60 - 70 kg 5' 152 cm
Part # Approximate Capacity StrokeRPA-1 0.5 - 1.5 lb 0.2 - 0.7 kg 5' 152 cm
RPA-2 1.5 - 3.0 lb 0.7 - 1.4 kg 5' 152 cm
RPA-3 3.0 - 5.0 lb 1.4 - 2.3 kg 5' 152 cm
Part # Approximate Capacity StrokeRMA-7L 5 - 10 lb 2.3 - 4.8 kg 8' 243.8 cm
RMA-15L 10 - 15 lb 4.5 - 6.8 kg 8' 243.8 cm
RMA-20L 15 - 23 lb 6.8 - 10.4 kg 8' 243.8 cm
www.eagle-premier.com 15
ACCESSORIES
5105FRL UNITS
AFRL-2-CCompact FRL
7070Compact FRL
AFRL-3Full Size FRL
5105INLINE LUBRICATORS
5105INLINE REGULATORS
In order to increase the life of your tools, we recommend that you install an Eagle filter, regulator and lubricator between the air supply and power tool.
lFilter: Traps the moisture before it enters the air tool.
lRegulator: Adjusted to the correct air pressure, maintaining consistent performance.
lLubricator: Allows the proper amount of lubrication needed for top performance.
lThese mini-type lubricators keep air operated tools performing with greater reliability. Each tool's lubrication can be adjusted easily right on the tool.
lInstalled inline with the air line immediately before the tools air inlet fitting.
lInline regulators allow easy adjustment of the airflow to each tool with the turn of a dial.
lInstalled inline with the air line immediately before the tool's air inlet fitting.
Part #
NPT Port Size
Flow Rate SCFM
AFRL-2 1/4" 70
AFRL-3 3/8" 140
AFRL-4 1/2" 140
AFRL-8 1" 180
Part #
NPT Port Size
Flow Rate SCFM
AFRL-2-C 1/4" 60
AFRL-3-C 3/8" 105
7070 3/8"
Part # Description7006 Mini Inline Lubricator
1/4" NPT
7007 Midget Inline Lubricator 1/4" NPT
7008 Master Inline Lubricator 3/8" NPT
Part # Description932-110-0A 1/4" NPT
932-100-0 1/8" NPT
www.eagle-premier.com16
ACCESSORIES
5105COILED HOSES
5105STRAIGHT HOSE BY THE FOOT
5105BRASS QUICK COUPLERS
5105AIR HOSE FITTING
Swivel
Rigid
lDurable polyurethane hose.
lAssemblies include reusable swivel fitting.
lApproximate burst pressure 428 PSI @ 68oF.
lWorking temperature -104oF to +175oF.
lStraight hose available by the foot with or without fittings.
lAsk about full reel pricing.
lDurable polyurethane hose.
lExcellent recoil memory.
lMaximum flexibility and lightweight.
lTransparent hose color (opaque available).
lCustom colors available.
lHigh chemical resistance.
lProvides simple way of connecting and disconnecting air tools to hose.
lManual ball couplers designed for use with ergonomic twist plugs. Brass with nitrate seals.
lRated to 300 PSI, from -40oF to +250oF.
lSize fitting to hose size and air flow.
lProvides air hose connections.
lSwivel fitting helps keep hose from twisting.
lSize fitting to hose size and air flow.
Part # OD ID Length
ASH-250C-10MSZ 3/8" 1/4" 10'
ASH-250C-15MSZ 3/8" 1/4" 15
ASH-250C-25MSZ 3/8" 1/4" 25'
ASH-375C-25MSZ 9/16" 3/8" 25'
ASH-500C-15MSZ 3/4" 1/2" 15'
ASH-500C-25MSZ 3/4" 1/2" 25'
Part # Inner Diameter
ASH-250Z 1/4" ID
ASH-375Z 3/8" ID
ASH-500Z 1/2" ID
Part # Description250-RZ 1/4" NPT Rigid250-SZ 1/4" NPT Swivel375-RZ 3/8" NPT Rigid375-SZ 3/8" NPT Swivel500-SZ 1/2" NPT Rigid
Part # Description
B23 1/4" NPT F x 1/4” QC
B23E 3/8" NPT F x 1/4” QC
B25 3/8" NPT F x 3/8” QC
www.eagle-premier.com 17
ACCESSORIES
5105ERGONOMIC SWIVEL COUPLERS
5105360O SWIVEL AIR CONNECTOR
l360o rotation for ease of moving tools.
l45o angle reduces hose bending.
lFor most portable non-impacting.
lSize fitting to hose size and air flow.
l360o rotation for difficult angles.
lFor most portable air tools including screwdrivers, drills, grinders, impacts, sanders, and more.
lSize fitting to hose size and air flow.
Part # Description
TS-30NP-2NPT 3/8 NPT Female x 1/4 NPT Male
TS-20NP-2NPT 1/4 NPT Female x 1/4 NPT Male
TS-20US-2NPT 1/4 US Plug x 1/4 NPT Male
TS-30US-2NPT 3/8 US Plug x 1/4 NPT Male
2FAP-N3M-UA 1/4 NPT Female x 3/8 NPT Male
TS-20US-3NPT 1/4 US Plug x 3/8 NPT Male
3FAN3F-N3M 3/8 US Plug x 3/8 NPT Male
Part # Inlet Weight
7025S 1/4" NPT 2.5 oz
7021 1/4" NPT 2.5 oz
7021AG 1/4" NPT 3.2 oz
7041A 3/8" NPT 2.5 oz
7041AG 3/8" NPT 3.3 oz
7051 1/2" NPT 6.6 oz
www.eagle-premier.com18
ACCESSORIES: BITS & SOCKETS
ODID
L
MAG-O-NETS®
l Turn virtually any standard screwdriver bit into a magnetized bit by simply sliding on a Mag-O-Net® collar.
l An easy, cost-effective alternative to traditional magnetic bit holder and insert bit combination.
l Reusable and interchangeable - once a bit is worn out, simply remove and slide onto the next bit.
Additional sizes of bits and sockets are available upon request.
Call Eagle at 1-800-852-1368.
L
1/4
H
BIT HOLDERS
L LPart No mm in
1/4” Hex, MagneticA3BHM-3 75 2.94A3BHM-6 150 5.91
L
PHILLIPS POWER BITS
Point L LPart No Size mm inA3S2-3 2 75 2.95A3S2-6 2 150 5.91A3S3-3 3 75 2.95A3S3-6 3 150 5.91
L
PHILLIPS INSERT BITS
Point L LPart No Size mm inA38S2-1 2 25 0.98A38S3-1 3 25 0.98
L
SLOTTED POWER BITS
Screw L L Blade BladePart No Size mm in Thickness WidthA3M8-3 8 75 2.95 0.04 0.28A3M10-3 10 75 2.95 0.05 0.31
L
SLOTTED INSERT BITS
Screw L L Blade BladePart No Size mm in Thickness WidthA38M8-1 8 25 0.98 0.04 0.25A38M10-1 10 25 0.98 0.05 0.28
L
SQUARE RECESS POWER BITS
Point Nominal L LPart No Size Square Size mm inA3R1/8-2.75 2 1/8" 70 2.76A3R9/64-2.75 3 9/64" 70 2.76
L
SQUARE RECESS INSERT BITS
Point Nominal L LPart No Size Square Size mm inA38R1/8-1 2 1/8" 25 0.98A38R9/64-1 3 9/64" 25 0.98
Inner Outer LengthPart No (ID) (OD) mm
AM1/4Z 7 mm 19 mm 10 mmAM5Z 6 mm 17.5 mm 10 mmAM3/16Z 3/16” 17.5 mm 10 mm
www.eagle-premier.com 19
ACCESSORIES: BITS & SOCKETS
STANDARD FASTENER TOOLSConnect your tool to the application with Bits, Sockets, and Nutsetters from Eagle.
Eagle has assembled the most complete package of com-monly used screwdriver bits and nutsetters in the industry. Our goal is to supply you with the highest quality bits and nutsetters for all your fastener needs. If you’re in electronics, aerospace, automotive, or general industry, Eagle has the bits and nutsetters to fit your needs.
Additional types and sizes of fastener tools are available upon request. Contact Eagle at 1-800-852-1368.
H(6PT)
Sq.
L
ØD1 ØD2
TYPE A
TYPE B
TYPE C
L
ØD2
ØD2
L
ØD1
H(6PT)
Sq.
L
ØD1 ØD2
TYPE A
TYPE B
TYPE C
L
ØD2
ØD2
L
ØD1
H(6PT)
Sq.
L
ØD1 ØD2
TYPE A
TYPE B
TYPE C
L
ØD2
ØD2
L
ØD1
D1 D1 D2 D2 L L
PART NO HEX MM IN MM IN MM IN
3/8” Square Drive
SAE A31/4 1/4” 10 0.39 19 0.75 34 1.34
A35/16 5/16” 12 0.47 19 0.75 34 1.34A33/8 3/8” 15 0.59 19 0.75 34 1.34
METR
IC A306 6 mm 10 0.39 19 0.75 34 1.34A307 7 mm 13 0.49 20 0.79 32 1.26A308 8 mm 14 0.55 20 0.79 32 1.26
3/8” Square Drive, DeepA307-2 7 mm 13 0.49 20 0.79 50 1.97A307-2.75 7 mm 13 0.49 20 0.79 70 2.76A308-2 8 mm 14 0.55 20 0.79 50 1.97
3/8” Square Drive, Magnetic
SAE A31/4MP 1/4” 10 0.39 19 0.75 34 1.34
A35/16MP 5/16” 12 0.47 19 0.75 34 1.34A33/8MP 3/8” 15 0.59 19 0.75 34 1.34
METR
IC A308MP 8 mm 14 0.55 20 0.79 32 1.26A310MP 10 mm 17 0.65 20 0.79 32 1.26A311MP 11 mm 17 0.65 19 0.75 34 1.34
1/2” Square Drive
SAE A43/8 3/8” 16 0.63 25 0.98 38 1.50
A47/16 7/16” 18 0.69 25 0.98 38 1.50A41/2 1/2” 19 0.75 25 0.98 50 1.97
METR
IC A408 8 mm 16 0.61 25 0.98 40 1.58A409 9 mm 16 0.63 25 0.98 40 1.58A410 10 mm 18 0.69 25 0.98 40 1.58
1/2” Square Drive, Deep
SAE A43/8-3.25 3/8” 17 0.67 25 0.98 82 3.23
A47/16-3.25 7/16” 19 0.73 25 0.98 82 3.23A41/2-3.25 1/2” 22 0.85 25 0.98 82 3.23
METR
IC
A410-2 10 mm 18 0.69 25 0.98 50 1.97A410-3 10 mm 18 0.69 25 0.98 75 2.95A410-3.25 10 mm 17 0.67 25 0.98 82 3.23A411-3.25 11 mm 19 0.73 25 0.98 82 3.23
IMPACT SOCKETS
H Sq.
SQ D1 D1 L L
PART NO DRIVE HEX MM IN MM IN
ADC-2S 1/4” 1/4” 19 0.75 38 1.50ADC-3S 3/8” 1/4” 20 0.79 42 1.65ADC-4S 1/2” 1/4” 19 0.75 46 1.81ADC-3SH7/16 3/8” 7/16” 25 0.98 46 1.81ADC-4SH7/16 1/2” 7/16” 33 1.30 55 2.17
H Sq.
L
L1
QUICK CHANGE CHUCKS
ALLEN SOCKETS
D1 D1 D2 D2 L L
PART NO HEX MM IN MM IN MM IN
1/2” Square Drive, MagneticA408MP 8 mm 16 0.61 25 0.98 40 1.58A410MP 10 mm 18 0.69 25 0.98 40 1.58A412MP 12 mm 21 0.81 25 0.98 40 1.58
3/4” Square Drive
SAE A611/16 11/16” 30 1.18 44 1.73 50 1.97
A63/4 3/4” 32 1.26 44 1.73 50 1.97A613/16 13/16” 35 1.38 44 1.73 50 1.97
METR
IC A614 14 mm 24 0.95 38 1.50 55 2.17A616 16 mm 27 1.06 44 1.73 50 1.97A617 17 mm 30 1.18 38 1.50 55 2.17
3/4” Square Drive, Deep
SAE A611/16-4 11/16” 31 1.22 44 1.73 100 3.94
A63/4-4 3/4” 33 1.30 44 1.73 100 3.94A613/16-4 13/16” 36 1.42 44 1.73 100 3.94
METR
IC A617-4 17 mm 31 1.22 44 1.73 100 3.94A618-4 18 mm 32 1.26 44 1.73 100 3.94A619-4 19 mm 33 1.30 38 1.50 100 3.94
1” Square DriveSA
E A87/8 7/8” 37 1.46 54 2.13 59 2.32A815/16 15/16” 38 1.50 54 2.13 59 2.32A81 1” 41 1.61 54 2.13 59 2.32
METR
IC A817 17 mm 31 1.22 50 1.97 63 2.48A819 19 mm 33 1.30 50 1.97 63 2.48A821 21 mm 37 1.46 50 1.97 63 2.48
L1 L1 L L
PART NO HEX MM IN MM IN
3/8” Square DriveA31/4C 1/4” 10 0.39 42 1.65A304C 4 mm 10 0.39 42 1.65
1/2” Square DriveA41/4C 1/4” 25 0.98 50 1.97A405C 5 mm 25 0.98 50 1.97
www.eagle-premier.com20
ACCESSORIES: BITS & SOCKETS
Additional types and sizes of fastener tools are available upon request. Contact Eagle at 1-800-852-1368.
Sq.
L
H
Sq.
L
H Sq.
L
H
EXTENSIONS
L
1/4
H
BIT HOLDERS
SOCKET ADAPTERS
D
LM
H Sq.
L
D1
D2
UNIVERSAL SOCKETS
Description of Bits and Nutsetters Part Number Nomenclature
BITS A3S = Phillips® Power DriveA3W = Double Ended Phillips®
A38S = Phillips® InsertA39S = Phillips® Insert Reduced NoseA3M = Slotted Power DriveA38M = Slotted InsertA3MT = Slotted Power Drive Reduced NoseA3C = Allen Socket Head Power DriveA38C = Allen Socket Head InsertA3R = Square Recess Power DriveA3RT = Square Recess Turned Down (Power)A38R = Square Recess InsertA3T = Torx® Power DriveA38T = Torx® InsertA3TS = Torq-Set® Power DriveA38TS = Torq-Set® InsertA3TA = Triangle Power DriveA3TW = Tri-Wing® Power DriveA38TW = Tri-Wing® InsertA7 = 7/16 Power DriveAS = Electric Type Phillips®
Precedes Part Number
BITS (Cont.)
AM = Electric Type SlottedATW = ElectricType Tri-Wing®
AT = Electric Hios Type Torx®
A26S = Electric Driver Phillips®
A26M = Electric Driver SlottedA26C = Electric Driver Allen Socket HeadA3BHM = Insert Bit Holder (Magnetic Type)A3BHD = Insert Bit Holder (Non Magnetic)
NUTSETTERS A3B = NutsetterA3BMP = Magnetic (MP) Pressed TypeA3BMS = Magnetic (MS) Spring LoadedA3BMT = Magnetic (MT) Tube TypeA3BU = Universal Nutsetter
MAG-O-NETS
AM = AIMCO Mag-O-Net®
BITS
PZ = Pozidriv®
PZACR = Pozidriv® ACR®
SDV = Supadriv®
TR = Torx® Tamper ResistantACRI = ACR® InstallationACR = ACR® RemoveACRB = ACR® 4x4 Both Install and RemoveE4 = Electric 4mm diameterE5 = Electric 5mm diameterRS = Reduced Shank
Contained Within Part Number
SQ L L D DPART NO DRIVE HEX MM IN MM IN
A375E 3/8” 3/8” 75 2.95 20 0.79A405E 1/2” 1/2” 51 2.01 30 1.18A610E 3/4” 3/4” 100 3.94 44 1.73A810E 1” 1” 102 4.02 54 2.13A1220E 1-1/4” 1-1/4” 200 7.87 60 2.36A1418E 1-1/2” 1-1/2” 178 7.01 84 3.31A2426E 2-1/2” 2-1/2” 264 10.39 137 5.39
L L
PART NO MM IN
1/4” Hex, MagneticA3BHM-3 75 2.94A3BHM-4 100 3.94A3BHM-6 150 5.91A3BHM-8 200 7.87A3BHM-10 250 9.84
FEMALE MALE D D L L
PART NO SQ. DRIVE SQ. DRIVE MM IN MM IN
A302A 3/8” 1/4” 22 0.87 35 1.38A403A 1/2” 3/8” 25 0.98 37 1.46A504A 5/8” 1/2” 35 1.38 47 1.46A604A 3/4” 1/2” 38 1.50 53 2.09A806A 1” 3/4” 50 1.97 70 2.76A128A 1-1/4” 1” 60 2.36 76 2.99A#508A Spline #5 1” 60 2.36 90 3.54
D1 D1 D2 D2 L L
PART NO HEX MM IN MM IN MM IN
3/8” Square DriveA310U 10 mm 16 0.63 20 0.79 55 2.17A311U 11 mm 16 0.63 20 0.79 60 2.36
1/2” Square DriveA412U 12 mm 20.5 0.81 25 0.98 70 2.76A413U 13 mm 19 0.75 24 0.95 70 2.76
www.eagle-premier.com 21
ACCESSORIES: BITS & SOCKETS
Additional types and sizes of fastener tools are available upon request.
For custom parts, please contact us for more information.
1-800-852-1368
L
L
12
Double-Ended
TORX POWER BITS
H
L
POINT L L
PART NO SIZE MM IN
A3S0-2 0 50 1.97A3S1-2 1 50 1.97A3S1-2.75 1 70 2.76A3S1-3 1 75 2.95A3S1-3.5 1 90 3.54A3S1-4 1 100 3.94A3S1-6 1 150 5.91A3S2-1.2 2 30 1.18A3S2-1.6 2 40 1.57A3S3-2 3 50 1.97A3S3-2.75 3 70 2.76
A3W1-3 1 75 2.94A3W1-4 1 100 3.94A3W2-2 2 50 1.97A3W2-3 2 75 2.94A3W2-4 2 100 3.94A3W2-6 2 150 5.91A3W2-8 2 200 7.87A3W2-10 2 250 9.84A3W2-12 2 300 11.81A3W3-2 3 50 1.97A3W3-3 3 75 2.94A3W3-4 3 100 3.94A3W3-6 3 150 5.91A3W3-8 3 200 7.87
TORX L L
PART NO SIZE MM IN
A3T6-2 T6 50 1.97A3T7-2 T7 50 1.97A3T7-2.75 T7 70 2.76A3T7-3.5 T7 90 3.54A3T7-6 T7 150 5.91A3T8-2 T8 50 1.97A3T9-2.75 T9 70 2.76
L LPART NO HEX MM IN
A3B1/4-2 1/4” 50 1.97A3B1/4-2.5 1/4” 63 2.50A3B5/16-2 5/16” 50 1.97A3B5/16-2.5 5/16” 63 2.50A3B3/8-2 3/8” 50 1.97A3B3/8-2.5 3/8” 63 2.50A3B05-2.75 5 mm 70 2.76A3B55-1.2 5.5 mm 30 1.18A3B55-2.75 5.5 mm 70 2.76A3B55-4 5.5 mm 100 3.94A3B06-2.75 6 mm 70 2.76A3B07-1.2 7 mm 30 1.18A3B07-2 7 mm 50 1.97A3B07-2.75 7 mm 70 2.76A3B07-4 7 mm 100 3.94A3B08-1.2 8 mm 30 1.18A3B08-2 8 mm 50 1.97A3B08-2.75 8 mm 70 2.76A3B08-4 8 mm 100 3.94A3B08-6 8 mm 150 5.91A3B08-8 8 mm 200 7.87A3B09-2.75 9 mm 70 2.76A3B09-4 9 mm 100 3.94A3B10-1.2 10 mm 30 1.18A3B10-2 10 mm 50 1.97A3B10-2.75 10 mm 70 2.76A3B11-2.75 11 mm 70 2.76A3B12-1.2 12 mm 30 1.18A3B13-2.75 13 mm 70 2.76A3B14-2.75 14 mm 70 2.76A3B16-2.75 16 mm 70 2.76A3B17-2.75 17 mm 70 2.76
PHILLIPS POWER BITSNUTSETTERS
www.eagle-premier.com22
WARRANTY INFORMATION
www.eagle-premier.com
NEW TOOL AND ACCESSORY WARRANTYAny new tool or accessory branded with the Eagle name, and purchased from Eagle Group, Inc (EAGLE), or through one of its authorized distributors or agents, is warranted to the original buyer against defects in materials and workmanship for a period of one (1) year* from date of delivery. Under the terms of this warranty, EAGLE will repair or replace any product or accessory warranted hereunder and returned freight prepaid proving to EAGLE's satisfaction to be defective as a result of workmanship or materials. In order to qualify for this warranty, written notice to EAGLE must be given immediately upon discovery of such defect, at which time EAGLE will issue an authorization to return the tool. The defective item must be promptly returned to an authorized EAGLE service center with all freight charges prepaid.
REPAIRED TOOL WARRANTYOnce a tool is beyond the new product warranty period, as detailed above, EAGLE will provide repair warranty on pneumatic tools for a period of 90 days* beyond the warrantied repair date.
EXCLUSION FROM WARRANTYThis warranty is valid only on products purchased from EAGLE, or thru its authorized distributors or agents. EAGLE shall have no obligation pursuant to the EAGLE Warranty with respect to any tools or accessories which in EAGLE's sole judgment have been altered, damaged, misused, abused, badly worn, lost or improperly maintained. This Warranty is null and void if the customer, or any other person other than an authorized representative of EAGLE, has made any attempt to service or modify the tool or accessory prior to its return to EAGLE under this Warranty.
The warranty provision with respect to each such product may be amended by EAGLE from time to time in its sole discretion. The liability of EAGLE hereunder shall be limited to replacing or repairing, at its option, any products which are returned freight prepaid to EAGLE and which EAGLE determines to be defective as described above or, at EAGLE's option, refunding the purchase price of such products.
EAGLE reserves the right to make periodic changes in construction or tool design at any time. EAGLE specifically reserves the right to make these changes without incurring any obligation or incorporating such changes or updates in tools or parts previously distributed.
THE EAGLE WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED, AND EAGLE EXPRESSLY DISCLAIMS ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. THIS WARRANTY SETS FORTH THE SOLE AND EXCLUSIVE REMEDY IN CONTRACT, TORT, STRICT LIABILITY, OR OTHERWISE.
THIS WARRANTY IS THE ONLY WARRANTY MADE BY EAGLE WITH RESPECT TO THE GOODS DELIVERED HEREUNDER, AND MAY BE MODIFIED OR AMENDED ONLY BY A WRITTEN INSTRUMENT SIGNED BY A DULY AUTHORIZED OFFICER OF EAGLE.
LIMITATION OF LIABILITYEAGLE'S LIABILITY PURSUANT TO WARRANTY OF THE PRODUCTS COVERED HEREUNDER IS LIMITED TO REFUND OF THE PURCHASE PRICE. IN NO EVENT SHALL EAGLE BE LIABLE FOR COSTS OF PROCUREMENT OF SUBSTITUTE GOODS BY THE BUYER. IN NO EVENT SHALL EAGLE BE LIABLE FOR ANY SPECIAL, CONSEQUENTIAL, INCIDENTAL OR OTHER DAMAGES (INCLUDING WITHOUT LIMITATION, LOSS OF PROFIT) WHETHER OR NOT EAGLE HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH LOSS, HOWEVER CAUSED, WHETHER FOR BREACH OR REPUDIATION OF CONTRACT, BREACH OF WARRANTY, NEGLIGENCE OR OTHERWISE. THIS EXCLUSION ALSO INCLUDES ANY LIABILITY WHICH MAY ARISE OUT OF THIRD PARTY CLAIMS AGAINST BUYER. THE ESSENTIAL PURPOSE OF THIS PROVISION IS TO LIMIT THE POTENTIAL LIABILITY OF EAGLE ARISING OUT OF THIS AGREEMENT AND/OR SALE.
Note: The EAGLE Warranty confers specific legal rights, however some states or jurisdictions may not allow certain exclusions or limitations within this warranty.
* All warranty periods addressed herein are determined using a standard shift, eight-hour work day.
EAGLEAttn: Service Department
10000 SE Pine StreetPortland, OR 97216
877.273.3903
www.eagle-premier.com 23www.eagle-premier.com 23
NOTES
TM
LIT-E380 Rev 06-15, Printed in USA, ©2015 AIMCO
Corporate Headquarters
10000 SE Pine St.Portland, OR 97216
www.eagle-premier.com
Call Toll Free until 8pm EST
Phone: (877) 273-3903
Fax: (800) 959-6601
AIMCO Corporation de Mexico SA de CV
Ave. Cristobal Colon 14529Chihuahua, Chihuahua. 31125
MEXICO
Toll Free : +52 (800) 801-1600 Direct :+52 (614) 380-1010 Fax : +52 (614) 380-1019
AIMCO ChinaRoom 607, No.3998 Hongxin Rd, Dibao Plaza, Minhang District,
Shanghai, 201103China
Phone: 0086-21-34319246 Fax: 0086-21-34319245
AIMCO SpainAvenida Río Gallo, 431
19174 Galápagos - GuadalajaraSpain
Phone: +34 673 34 99 25
WWW.AIMCO-GLOBAL .COM