POWERLATCH COUPLER HYDRAULIC, 5T (R CLASS )
This chart has not been checked against buckets manufactured in Japan/Korea. Also there may be a possibility that the coupler may foul the centre head plate on buckets not manufactured to OEM dimensions. Therefore,please advise if coupler is required for use with Japanese/Korea manufactured buckets/attachments at time of inquiry/order. Important Note: The PowerLatch may allow customers to pick up/operate with buckets/attachmentsfrom different ranges. Miller advise use on recommended models listed only (as detailed). Do not over specify bucket or attachment as this may cause machine instability. All Information supplied herein may be subject tochange without prior notice. The operating weight of the machines indicated in each PowerLatch range is only an approximation. There may be a possibility that due to the design parameters of the PowerLatch coupler amachine may appear in a different weight range.© The copyright in this drawing and in the articles shown belong to MILLER UK LTD and no reproduction in whole or in part of this drawing or the articles shown may be made without prior written permission. The articlesshown on this drawing may be changed or modified without any prior warning.
The coupler will pick up buckets and toolsmade for the following machines:
• CASE CX40, CX45 & CX55B
• CAT 305D, 305E
• HITACHI ZX45, ZX48 & ZX52
• HITACHI ZX60 USB
•KOMATSUPC40,PC45,PC50 &PC55
• KUBOTAU45-3, U50-3 & KX161
•TAKEUCHITB145,TB153FR&TB250
• VOLVO ECR48, EC55B, ECR55C &ECR58
DATE: 07/03/2013 ISSUE: 1 PRODUCED BY: SF
MILLER UK LIMITED SPECIFICATION SHEET
• Pin diameter 45 mm
• Pin centre range max 265mm, min 220mm
• Minimum width 149mm(BETWEEN BUCKET BOSSES)
• Approximate weight of coupler = 55kg
The PowerLatch will also pick up the Miller
Scoop for enhanced machine performance
and productivity
Miller Direct Mount BucketMiller Scoop Bucket
POWERLATCH COUPLER HYDRAULIC, 6-9T (RANGE 3)
This chart has not been checked against buckets manufactured in Japan/Korea. Also there may be a possibility that the coupler may foul the centre head plate on buckets not manufactured to OEM dimensions. Therefore,please advise if coupler is required for use with Japanese/Korea manufactured buckets/attachments at time of inquiry/order. Important Note: The PowerLatch may allow customers to pick up/operate with buckets/attachmentsfrom different ranges. Miller advise use on recommended models listed only (as detailed). Do not over specify bucket or attachment as this may cause machine instability. All Information supplied herein may be subject tochange without prior notice. The operating weight of the machines indicated in each PowerLatch range is only an approximation. There may be a possibility that due to the design parameters of the PowerLatch coupler amachine may appear in a different weight range.© The copyright in this drawing and in the articles shown belong to MILLER UK LTD and no reproduction in whole or in part of this drawing or the articles shown may be made without prior written permission. The articlesshown on this drawing may be changed or modified without any prior warning.
The coupler will pick up buckets and toolsmade for the following machines:
• CASE CX75SR, CX80
• CAT 307, 307C & 308D
• HITACHI ZX80 & ZX85
• HYUNDAI R55-7 & R55W-7
• KOMATSU PC75, PC88, PC95,PW95, PW98, PC110 & PC80MR-3
• KUBOTA KX80
• LIUGONG CLG908
• NEW HOLLAND E70SR & E80SR
• TAKEUCHI TB175 & TB180
• VOLVO ECR88
DATE: 19/08/2013 ISSUE: 1 PRODUCED BY: SF
MILLER UK LIMITED SPECIFICATION SHEET
The PowerLatch will also pick up the Miller
Scoop for enhanced machine performance
and productivity
Miller Direct Mount BucketMiller Scoop Bucket
• Pin diameter 50 & 60 mm
• Pin centre range
- 50mm Dia. Pins,max 317mm, min 280mm
- 60mm Dia. Pins,max 320mm, min 290mm
• Minimum width 164mm(BETWEEN BUCKET BOSSES)
• Approximate weight of coupler = 100kg
POWERLATCH COUPLER HYDRAULIC, 10-13T (RANGE 4)
This chart has not been checked against buckets manufactured in Japan/Korea. Also there may be a possibility that the coupler may foul the centre head plate on buckets not manufactured to OEM dimensions. Therefore,please advise if coupler is required for use with Japanese/Korea manufactured buckets/attachments at time of inquiry/order. Important Note: The PowerLatch may allow customers to pick up/operate with buckets/attachmentsfrom different ranges. Miller advise use on recommended models listed only (as detailed). Do not over specify bucket or attachment as this may cause machine instability. All Information supplied herein may be subject tochange without prior notice. The operating weight of the machines indicated in each PowerLatch range is only an approximation. There may be a possibility that due to the design parameters of the PowerLatch coupler amachine may appear in a different weight range.© The copyright in this drawing and in the articles shown belong to MILLER UK LTD and no reproduction in whole or in part of this drawing or the articles shown may be made without prior written permission. The articlesshown on this drawing may be changed or modified without any prior warning.
The coupler will pick up buckets and toolsmade for the following machines:
• CASE CX130B & CX135SR
• CAT 311D, 312D & 314D
• DOOSAN S140, DX140, DX140W &DX160
• HITACHI ZX130 & ZX135
• HYUNDAI R130, R140 & R145
• JCB JS130 & JS145
• KOBELCO SK135
• KOMATSU PC130, PC138, PW140 &PW148
• LIUGONG CLG915
• NEW HOLLAND E135SR
• VOLVO EC140C & ECR145C
DATE: 19/08/2013 ISSUE: 1 PRODUCED BY: SF
MILLER UK LIMITED SPECIFICATION SHEET
ThePowerLatch will also pick up the Miller
Scoop for enhanced machine performance
and productivity
Miller Direct Mount BucketMiller Scoop Bucket
• Pin diameter 60 & 65 mm
• Pin centre range
- 60mm Dia. Pins,max 415mm, min 345mm
- 65mm Dia. Pins,max 420mm, min 355mm
• Minimum width 216mm(BETWEEN BUCKET BOSSES)
• Approximate weight of coupler = 180kg
POWERLATCH COUPLER HYDRAULIC, 14-18T (RANGE 5)
This chart has not been checked against buckets manufactured in Japan/Korea. Also there may be a possibility that the coupler may foul the centre head plate on buckets not manufactured to OEM dimensions. Therefore,please advise if coupler is required for use with Japanese/Korea manufactured buckets/attachments at time of inquiry/order. Important Note: The PowerLatch may allow customers to pick up/operate with buckets/attachmentsfrom different ranges. Miller advise use on recommended models listed only (as detailed). Do not over specify bucket or attachment as this may cause machine instability. All Information supplied herein may be subject tochange without prior notice. The operating weight of the machines indicated in each PowerLatch range is only an approximation. There may be a possibility that due to the design parameters of the PowerLatch coupler amachine may appear in a different weight range.© The copyright in this drawing and in the articles shown belong to MILLER UK LTD and no reproduction in whole or in part of this drawing or the articles shown may be made without prior written permission. The articlesshown on this drawing may be changed or modified without any prior warning.
The coupler will pick up buckets and toolsmade for the following machines:
• CASE CX160B, CX180B, WX165 &WX185
• CAT 315D
• HITACHI ZX160
• HYUNDAI R160, R170W & R180
• JCB JS160
• KOBELCO SK150
• KOMATSU PC160 & PC180
• NEW HOLLAND E175B & E175W
•VOLVOEC160C,EC180C,EW160C&EW180C
DATE: 29/02/2012 ISSUE: 1 PRODUCED BY: SF
MILLER UK LIMITED SPECIFICATION SHEET
Miller Scoop Bucket
The PowerLatch will also pick up the Miller
Scoop for enhanced machine performance
and productivity
Miller Direct Mount BucketMiller Scoop Bucket
• Pin diameter 70 & 80 mm
• Pin centre range
- 70mm Dia. Pins,max 472mm, min 376mm
- 80mm Dia. Pins,max 477mm, min 391mm
• Minimum width 272mm(BETWEEN BUCKET BOSSES)
• Approximate weight of coupler = 270kg
POWERLATCH COUPLER HYDRAULIC, 19-21T (RANGE 6)
This chart has not been checked against buckets manufactured in Japan/Korea. Also there may be a possibility that the coupler may foul the centre head plate on buckets not manufactured to OEM dimensions. Therefore,please advise if coupler is required for use with Japanese/Korea manufactured buckets/attachments at time of inquiry/order. Important Note: The PowerLatch may allow customers to pick up/operate with buckets/attachmentsfrom different ranges. Miller advise use on recommended models listed only (as detailed). Do not over specify bucket or attachment as this may cause machine instability. All Information supplied herein may be subject tochange without prior notice. The operating weight of the machines indicated in each PowerLatch range is only an approximation. There may be a possibility that due to the design parameters of the PowerLatch coupler amachine may appear in a different weight range.© The copyright in this drawing and in the articles shown belong to MILLER UK LTD and no reproduction in whole or in part of this drawing or the articles shown may be made without prior written permission. The articlesshown on this drawing may be changed or modified without any prior warning.
The coupler will pick up buckets and toolsmade for the following machines:
• CASE CX210B
• CAT ‘B’LINKAGE
• DOOSAN DX180 & DX225
•HITACHIZX180,ZX200,ZX210,ZX225
• HYUNDAI R200, R210 & R235
• JCB JS190, JS200, JS210 & JS220
• KOBELCO SK200, SK210 & SK235
• KOMATSU PC210, PC228
• LIUGONG CLG922
• NEW HOLLAND E215
• VOLVO EC210C, EC220D
DATE: 19/08/2013 ISSUE: 1 PRODUCED BY: SF
MILLER UK LIMITED SPECIFICATION SHEET
• Pin diameter 80 mm
• Pin centre range max 520mm, min 430mm
• Minimum width 302mm(BETWEEN BUCKET BOSSES)
• Approximate weight of coupler = 310kg
The PowerLatch will also pick up the Miller
Scoop for enhanced machine performance
and productivity
Miller Direct Mount BucketMiller Scoop Bucket
POWERLATCH COUPLER HYDRAULIC, 22-27T (RANGE 7)
This chart has not been checked against buckets manufactured in Japan/Korea. Also there may be a possibility that the coupler may foul the centre head plate on buckets not manufactured to OEM dimensions. Therefore,please advise if coupler is required for use with Japanese/Korea manufactured buckets/attachments at time of inquiry/order. Important Note: The PowerLatch may allow customers to pick up/operate with buckets/attachmentsfrom different ranges. Miller advise use on recommended models listed only (as detailed). Do not over specify bucket or attachment as this may cause machine instability. All Information supplied herein may be subject tochange without prior notice. The operating weight of the machines indicated in each PowerLatch range is only an approximation. There may be a possibility that due to the design parameters of the PowerLatch coupler amachine may appear in a different weight range.© The copyright in this drawing and in the articles shown belong to MILLER UK LTD and no reproduction in whole or in part of this drawing or the articles shown may be made without prior written permission. The articlesshown on this drawing may be changed or modified without any prior warning.
The coupler will pick up buckets and toolsmade for the following machines:
• CASE CX240B & CX290B
• CAT ‘C’ & ‘CB’ LINKAGE
• DOOSAN DX255 & DX300
• HITACHI ZX240, ZX250 & ZX290
• HYUNDAI R250 & R290
• JCB JS240
• KOMATSU PC240 & PC290
• LIUGONG CLG925
• VOLVO EC250D & EC300D
DATE: 19/08/2013 ISSUE: 1 PRODUCED BY: SF
MILLER UK LIMITED SPECIFICATION SHEET
The PowerLatch will also pick up the Miller
Scoop for enhanced machine performance
and productivity
Miller Direct Mount BucketMiller Scoop Bucket
• Pin diameter 80 & 90 mm
• Pin centre range
- 80mm Dia. Pins,max 520mm, min 443mm
- 90mm Dia. Pins,max 525mm, min 458mm
• Minimum width 321mm(BETWEEN BUCKET BOSSES)
• Approximate weight of coupler = 445kg
POWERLATCH COUPLER HYDRAULIC, 28-35T (RANGE 8)
This chart has not been checked against buckets manufactured in Japan/Korea. Also there may be a possibility that the coupler may foul the centre head plate on buckets not manufactured to OEM dimensions. Therefore,please advise if coupler is required for use with Japanese/Korea manufactured buckets/attachments at time of inquiry/order. Important Note: The PowerLatch may allow customers to pick up/operate with buckets/attachmentsfrom different ranges. Miller advise use on recommended models listed only (as detailed). Do not over specify bucket or attachment as this may cause machine instability. All Information supplied herein may be subject tochange without prior notice. The operating weight of the machines indicated in each PowerLatch range is only an approximation. There may be a possibility that due to the design parameters of the PowerLatch coupler amachine may appear in a different weight range.© The copyright in this drawing and in the articles shown belong to MILLER UK LTD and no reproduction in whole or in part of this drawing or the articles shown may be made without prior written permission. The articlesshown on this drawing may be changed or modified without any prior warning.
The coupler will pick up buckets and toolsmade for the following machines:
• CASE 9033, CX330 & CX350B
• CAT ‘D’& ‘DB’LINKAGE
• DOOSAN DX340
• HITACHI ZX350
• HYUNDAI 320 & 380
• JCB JS330 & JS360
• KOBELCO SK350
• KOMATSU PC350
• LIUGONG CLG936
DATE: 19/08/2013 ISSUE: 1 PRODUCED BY: SF
MILLER UK LIMITED SPECIFICATION SHEET
ThePowerLatch will also pick up the Miller
Scoop for enhanced machine performance
and productivity
Miller Direct Mount BucketMiller Scoop Bucket
• Pin diameter 90 & 100 mm
• Pin centre range
- 90mm Dia. Pins,max 602mm, min 482mm
- 100mm Dia. Pins,max 607mm, min 500mm
• Minimum width 340mm(BETWEEN BUCKET BOSSES)
• Approximate weight of coupler = 560kg
POWERLATCH COUPLER HYDRUALIC, RANGE 9
This chart has not been checked against buckets manufactured in Japan/Korea. Also there may be a possibility that the coupler may foul the centre head plate on buckets not manufactured to OEM dimensions. Therefore,please advise if coupler is required for use with Japanese/Korea manufactured buckets/attachments at time of inquiry/order. Important Note: The PowerLatch may allow customers to pick up/operate with buckets/attachmentsfrom different ranges. Miller advise use on recommended models listed only (as detailed). Do not over specify bucket or attachment as this may cause machine instability. All Information supplied herein may be subject tochange without prior notice. The operating weight of the machines indicated in each PowerLatch range is only an approximation. There may be a possibility that due to the design parameters of the PowerLatch coupler amachine may appear in a different weight range.© The copyright in this drawing and in the articles shown belong to MILLER UK LTD and no reproduction in whole or in part of this drawing or the articles shown may be made without prior written permission. The articlesshown on this drawing may be changed or modified without any prior warning.
DATE: 10/01/2014 ISSUE: 1 PRODUCED BY: SF
MILLER UK LIMITED SPECIFICATION SHEET
Miller Scoop Bucket
The PowerLatch will also pick up the Miller
Scoop for enhanced machine performance
and productivity
Miller Direct Mount BucketMiller Scoop Bucket
• Pin diameter 100 & 110 mm
• Pin centre range
- 100mm Dia. Pins, max 603mm, min 557mm
- 110mm Dia. Pins, max 608mm, min 572mm
• Minimum width 401mm(BETWEEN BUCKET BOSSES)
The coupler will pick up buckets and toolsmade for the following machines:
• CASE CX470B / CX470C
•CAT329/336/345/349-TB’LINKAGE
• HITACHI ZX470
• HYUNDAI R480
• JCB JS460
• LIUGONG CLG950
• VOLVO EC360C / EC380D
• VOLVO EC460C / EC480D
