PowerMatch - Bosesistema, ya que pueden provocar averías o riesgo de incendio. ADVERTENCIA : Con el...

PowerMatch®

Configurable Professional Power Amplifiers

Installation and Operating Guide

PM8500 / PM8500N

PM8250 / PM8250N

PM4500 / PM4500N

PM4250 / PM4250N

Important Safety Information pro.Bose.com

Page 2 Installation and Safety Guidelines English

WARNING: This product is intended for installation by professional installers only.Thank you for selecting Bose® PowerMatch® amplifiers for your sound reinforcement system. This document is intended to provide professional installers with basic installation and safety guidelines for Bose PowerMatch amplifiers in typical fixed-installation systems. Please read this document before attempting installation. WARNING: Do not expose this apparatus to dripping or splashing, and do not place objects filled with liquids such as vases, on or near the apparatus. As with any electronic products, use care not to spill liquids into any part of the system. Liquids can cause a failure and/or a fire hazard.WARNING: To reduce the risk of fire or electric shock, do not expose this apparatus to rain.WARNING: Do not place any naked flame sources, such as lighted candles, on or near the apparatus.WARNING: Avoid touching uninsulated wiring or wiring terminals. This product’s audio wiring terminals carry voltage that can result in discomfort upon contact.Note: The product must be used indoors. It is neither designed nor tested for use outdoors, in recreational vehicles, or on boats.

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsu-lated dangerous voltage within the system enclosure that may be of sufficient magnitude to constitute a risk of electrical shock. Do not touch the output terminals while amplifier power is ON. Make all connections with amplifier OFF.

The exclamation point within an equilateral triangle, as marked on the system, is intended to alert the user to the presence of important operating and maintenance instructions in this installation guide.

CAUTION: Make no modifications to the amplifier or accessories. Unauthorized alternations may compromise safety, regulatory compliance, and system performance.CAUTION: This product shall be connected to an AC mains socket outlet with a protective earthing (grounding) connection.CAUTION: Where the AC mains plug is used as the disconnect device, such disconnect device shall remain fully operable.

Important Safety Instructions1. Read these instructions.2. Keep these instructions – for future reference.3. Heed all warnings – on the product and in all product documentation.4. Follow all instructions.5. Do not use this apparatus near water or moisture.6. Clean only with a dry cloth.7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. To ensure reliable

operation of the product and to protect it from overheating, put the product in a position and location that will not interfere with its proper ventilation.

8. Do not install near any heat sources, such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding-type plug has two blades and a third grounding prong. The wider blade or third prong is provided for your safety. If the provided plug does not fit in your outlet, consult an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched, particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11. Only use attachments/accessories specified by the manufacturer.12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer or sold with the apparatus.

When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. 13. Unplug this apparatus during lightning storms or when unused for long periods of time to prevent damage to this product.14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any

way such as power-supply cord or plug is damaged; liquid has been spilled or objects have fallen into the apparatus; the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. Do not attempt to service this product yourself. Opening or removing covers may expose you to dangerous voltages or other hazards. Please call Bose to be referred to an authorized service center near you.

15. To prevent risk of fire or electric shock, avoid overloading wall outlets, extension cords, or integral convenience receptacles.16. Do not let objects or liquids enter the product – as they may touch dangerous voltage points or short-out parts that could result

in a fire or electric shock.17. See product enclosure for safety-related markings.

English Installation and Safety Guidelines Page 3

pro.Bose.com Important Safety Information

18. The front panel LCD screen will illuminate when the product has mains power. If power is applied and the LCD screen is not illuminated, please send the unit for service.

19. Do not allow the unit to exceed the maximum operating ambient temperature of 40° C. Be aware of conditions in an enclosed rack that may increase the temperature above room ambient conditions.

This product conforms to all applicable EU directive requirements. The complete declaration of conformity can be found at www.Bose.com/compliance.

This symbol means the product must not be discarded as household waste, and should be delivered to an appropriate collection facility for recycling. Proper disposal and recycling helps protect natural resources, human health and the environment. For more information on disposal and recycling of this product, contact your local municipality, disposal service, or the shop where you bought this product.

This Product meets the immunity requirements for the E2 class EN55103-2 directive.Initial turn on inrush current: 14.8 Amps (230V / 50 Hz)Inrush current after 5 seconds AC mains interruption: 15.4 Amps (230V / 50 Hz)

Information About Products That Generate Electrical Noise (FCC Compliance Notice for U.S.)Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at one’s own expense.This product complies with CAN ICES-3 (A)/NMB-3 (A).

China Restriction of Hazardous Substances Table 中国有害物质限制表

Names and Contents of Toxic or Hazardous Substances or Elements 有毒或有害物质或元素的名称及成分

Toxic or Hazardous Substances and Elements 有毒或有害物质和元素

Part Name 零件名称Lead 铅

(Pb)Mercury 汞

(Hg)Cadmium 镉

(Cd)Hexavalent 六价铬

(CR(VI))

Polybrominated Biphenyl 多溴化联苯

(PBB)

Polybrominated diphenylether 多溴二苯醚

(PBDE)

PCBs 印刷电路板 X O O O O O

Metal Parts 金属零件 X O O O O O

Plastic Parts 塑料零件 O O O O O O

Speakers 扬声器 X O O O O O

Cables 线缆 X O O O O O

This table is prepared in accordance with the provisions of SJ/T 11364. 此表格符合 SJ/T 11364 条款。

O: Indicates that this toxic or hazardous substance contained in all of the homogeneous materials for this part is below the limit requirement of GB/T 26572.

0：表示此零件中所有同类物质包含的有毒或有害物质低于 GB/T 26572 中的限定要求。

X: Indicates that this toxic or hazardous substance contained in at least one of the homogeneous materials used for this part is above the limit requirement of GB/T 26572.

X：表示此零件使用的同类物质中至少有一种包含的有毒或有害物质高于 GB/T 26572 中的限定要求。

Taiwan Restriction of Hazardous Substances Table 台灣 BSMI 限用物質含有情況標示

Equipment name: PowerMatch Amplifiers 設備名稱：擴大機

Type designation 型號: 361810, 361811, 361813, 361814, 361815, 361816, 343547, 343546

Restricted substances and its chemical symbols 限制物質及其化學符號

Unit 裝置 Lead (Pb) 鉛

Mercury (Hg) 汞

Cadmium (Cd) 鎘

Hexavalent chromium (Cr+6)

六價鉻

Polybrominated biphenyls (PBB)

多溴化聯苯

Polybrominated diphenyl ethers (PBDE) 多溴聯苯醚

PCBs 印刷電路板 -

Metal Parts 金屬零件 -

Plastic Parts 塑膠零件

Speakers 揚聲器 -

Cables 連接線 -

Note 1: “” indicates that the percentage content of the restricted substance does not exceed the percentage of reference value of presence. 備註 1：「」表示限制物質的濃度百分比含量未超過參考值。

Note 2: The “−” indicates that the restricted substance corresponds to the exemption. 備註 2：「–」表示限制物質屬於豁免項目範圍。

Información de seguridad importante pro.Bose.com

Página 4 Instrucciones de instalación y de seguridad Español

ADVERTENCIA: Solo un instalador profesional deberá montar este producto.

Gracias por seleccionar los amplificadores Bose® PowerMatch® para su sistema de refuerzo de sonido. Este documento ofrece a los instaladores profesionales instrucciones básicas de instalación y seguridad para los amplificadores Bose PowerMatch en sistemas típicos de instalación fija. Lea este documento antes de intentar la instalación.

ADVERTENCIA: No exponga este aparato a salpicaduras o goteo. No coloque encima o cerca del aparato objetos que contengan líquidos, como jarrones. Al igual que con cualquier producto electrónico, evite que se derramen líquidos en los componentes del sistema, ya que pueden provocar averías o riesgo de incendio.

ADVERTENCIA: Con el fin de reducir el riesgo de descarga eléctrica, no exponga este producto a la lluvia o humedad.

ADVERTENCIA: No coloque sobre el aparato o cerca de éste llamas vivas, como por ejemplo, velas.

ADVERTENCIA: Evite tocar el cableado no aislado o los terminales de cableado. Los terminales de cableado de audio de este producto transmiten voltaje que puede causar incomodidad al contacto.

Nota: Este producto debe utilizarse en interiores. No está diseñado ni ha sido probado para uso al aire libre ni en embarcaciones.

El símbolo de relámpago con una flecha dentro de un triángulo equilátero indica al usuario que la caja del sistema puede contener una tensión sin aislar de magnitud suficiente para constituir un riesgo de descarga eléctrica. No toque los terminales de salida mientras el amplificador está encendido. Realice todas las conexiones con el amplificador apagado.

El signo de exclamación dentro de un triángulo equilátero, tal como aparece marcado en el sistema, avisa al usuario de que existen instrucciones de operación y mantenimiento importantes en esta guía de instalación.

PRECAUCIÓN: No realice modificaciones en el amplificador o los accesorios. Las alteraciones no autorizadas pueden comprometer aspectos de seguridad, cumplimiento normativo y rendimiento del sistema.

PRECAUCIÓN: Este producto se debe conectar a una toma de la red eléctrica con una conexión de tierra que sirva de protección.

PRECAUCIÓN: Si se utiliza la clavija de red como dispositivo de desconexión, deberá poder accionarse fácilmente.

Instrucciones de seguridad importantes1. Lea las siguientes instrucciones.

2. Guarde estas instrucciones por si necesita consultarlas en el futuro.

3. Respete todas las advertencias que se indican en el producto y en la documentación.

4. Siga todas las instrucciones.

5. No utilice este aparato cerca del agua o humedad.

6. Límpielo sólo con una bayeta seca.

7. No bloquee las aberturas de ventilación. Realice la instalación de acuerdo con las instrucciones del fabricante. Para garantizar el buen funcionamiento del producto y para protegerlo del sobrecalentamiento, colóquelo en una posición y una ubicación que no interfiera con una ventilación adecuada.

8. No lo instale cerca de fuentes de calor, tales como radiadores, salidas de aire caliente, cocinas u otros aparatos (incluidos amplificadores) que generen calor.

9. No elimine el mecanismo de seguridad del enchufe con toma a tierra o polarizado. Los enchufes polarizados disponen de dos clavijas, una de mayor tamaño que la otra. Los enchufes con toma a tierra tienen dos clavijas y un tercer terminal de tierra. La patilla más ancha y el tercer terminal se incluyen como medida de seguridad. Si el enchufe suministrado no encaja en la toma, póngase en contacto con un electricista para sustituir la toma antigua.

10. Proteja el cable de alimentación de forma que nadie lo pise ni quede pinzado, en particular cerca de enchufes, receptáculos de tomas múltiples y en el lugar en que sale del aparato.

11. Utilice sólo conexiones y accesorios suministrados por el fabricante.

12. Utilícelo sólo con el carrito, soporte, trípode, abrazadera o mesa suministrados por el fabricante o incluidos con el dispositivo. Cuando utilice un carrito, tenga cuidado al mover el carrito con el dispositivo para evitar que caiga y produzca daños.

13. Desenchufe el dispositivo si se produce una tormenta eléctrica o si no lo va a utilizar durante periodos prolongados de tiempo para evitar que se dañe.

pro.Bose.com

Español Instrucciones de instalación y de seguridad Página 5

pro.Bose.com Información de seguridad importante

14. Toda reparación debe ser realizada por personal cualificado. Lleve el dispositivo a reparar si presenta algún daño como, por ejemplo, si el cable de alimentación o el enchufe están dañados, si se han vertido líquidos o se han caído objetos sobre el dispositivo o si éste ha estado expuesto a la lluvia o humedad; si no funciona correctamente o se ha caído al suelo. No intente reparar este producto usted mismo. La apertura o retirada de las tapas le expondrá a tensiones peligrosas o a otros peligros. Póngase en contacto con Bose para conocer cuál es el centro de servicio técnico autorizado de su zona.

15. Para prevenir el riesgo de incendio o descargas eléctricas, evite sobrecargar los enchufes, alargadores o receptáculos de las tomas.

16. Evite que caigan objetos o líquidos sobre el producto, ya que podrían entrar en contacto con puntos de niveles de alta tensión o piezas que podrían sufrir un cortocircuito y causar incendios o descargas eléctricas.

17. Consulte las indicaciones de seguridad en la caja del producto.

18. La pantalla LCD del panel frontal se ilumina cuando el producto está conectado a la red. Si se conecta el aparato y no se ilumina la pantalla LCD, envíelo a reparar.

19. No exponga la unidad a temperaturas superiores a 40° C, su temperatura máxima de funcionamiento. Tenga en cuenta todas las situaciones que pueden darse en un bastidor cerrado y que podrían aumentar la temperatura por encima de las condiciones ambientales de la sala.

Este producto cumple todos los requisitos aplicables de las Directivas de la UE. Encontrará la declaración de conformidad completa en www.Bose.com/compliance.

Este símbolo significa que el producto no debe desecharse como residuo doméstico y debe enviarse a una planta para trata-miento de residuos apropiada para su reciclado. Una eliminación y un reciclado adecuados ayudan a proteger los recursos naturales, la salud humana y el medioambiente. Para obtener más información acerca de la eliminación y el reciclado de este producto, comuníquese con su municipalidad local, un centro de servicios de desecho o la tienda donde compró este producto.

Este producto cumple los requisitos de inmunidad que establece la Directiva EN55103-2 para la clase E2.

Corriente de irrupción en encendido inicial: 14,8 Amps (230 V / 50 Hz)

Corriente de irrupción después de 5 segundos de interrupción de la corriente de red: 15,4 Amps (230 V / 50 Hz)

Información sobre productos que generan ruido eléctrico (Nota de homologación FCC para EE UU)

Nota: este equipo se ha probado y ha demostrado que cumple con los límites para dispositivos digitales de clase B, de acuerdo con el apartado 15 de las normas de la FCC. Estos límites están diseñados para ofrecer una protección razonable contra las interferencias perjudiciales cuando el aparato se utiliza en un entorno comercial. Este equipo genera, utiliza y puede irradiar energía de radiofrecuencia y, si no se instala y se utiliza de acuerdo con el manual de instrucciones, podría ocasionar interferencias perjudiciales para las comunicaciones por radio. La utilización de este equipo en una zona residencial podría causar interferencias dañinas. En ese caso, la corrección de la interferencia correrá a cargo del usuario.

Este producto cumple la norma CAN ICES-3 (A)/NMB-3 (A).

Informations importantes pour la sécurité pro.Bose.com

Page 6 Installation et instructions de sécurité Français

AVERTISSEMENT : l’installation de ce produit est réservée à un technicien professionnel.

Merci d’avoir choisi des amplificateurs professionnels Bose® PowerMatch® pour votre système d’amplification du son. Ce document à l’intention des installateurs professionnels contient les directives de pose et de sécurité relatives aux amplificateurs professionnels Bose PowerMatch en installation fixe. Lisez attentivement ce document avant l’installation.

AVERTISSEMENT : protégez l’appareil de tout risque de ruissellement ou d’éclaboussure. Ne placez pas d’objets contenant des liquides, tels que des vases, sur l’appareil. Comme avec tout appareil électronique, veillez à ne pas renverser de liquides sur une partie quelconque de l’appareil. Les liquides peuvent provoquer des pannes et/ou un risque d’incendie.

AVERTISSEMENT : afin de limiter les risques d’incendie ou d’électrocution, n’exposez jamais ce produit à la pluie.

AVERTISSEMENT : ne placez aucune source de flamme nue, comme une bougie allumée, sur ou près de l’appareil.

AVERTISSEMENT : Évitez de toucher les bornes ou éléments de câblages non isolés. Les bornes de connexion audio de ce produit sont sous tension, ce qui peut provoquer une sensation désagréable en cas de contact.

Remarque : ce produit doit être utilisé en intérieur. Il n’a pas été conçu ni testé pour une utilisation en extérieur, dans des véhicules ou sur des bateaux.

Le symbole représentant un éclair avec une flèche à l’intérieur d’un triangle équilatéral est utilisé pour prévenir l’utilisateur de la présence d’une tension électrique dangereuse non isolée à l’intérieur de l’appareil. Cette tension est d’un niveau suffisamment élevé pour représenter un risque d’électrocution. Ne touchez pas les bornes de sortie lorsque l’amplificateur est allumé. Mettez l’amplificateur hors tension avant de réaliser toute connexion.

Le symbole représentant un point d’exclamation à l’intérieur d’un triangle équilatéral, tel qu’il figure sur le système, signale à l’utilisateur la présence d’instructions importantes relatives au fonctionnement et à l’entretien de l’appareil dans cette notice d’installation.

ATTENTION : n’apportez aucune modification à l’amplificateur ou aux accessoires. Toute modification non autorisée peut compromettre votre sécurité, le respect des réglementations et les performances.

ATTENTION : cet appareil doit être raccordé à une prise secteur dotée d’une mise à la terre.

ATTENTION : si la fiche d’alimentation est utilisée comme dispositif de débranchement de l’appareil, elle doit rester facilement accessible.

Instructions importantes relatives à la sécurité1. Veuillez lire ces instructions.

2. Conservez-les pour toute référence ultérieure.

3. Respectez tous les avertissements qui figurent sur le produit ou dans sa documentation.

4. Suivez toutes les instructions.

5. N’utilisez pas cet appareil à proximité d’eau ou d’une source d’humidité.

6. Utilisez uniquement un chiffon sec pour le nettoyage.

7. Ne bloquez jamais les orifices d’aération. Suivez les instructions du fabricant pour l’installation. Pour garantir un fonctionnement fiable du produit et le protéger contre tout risque de surchauffe, installez-le à un emplacement et dans une position permettant d’assurer une ventilation correcte.

8. N’installez pas cet appareil à proximité d’une quelconque source de chaleur, telle qu’un radiateur, une arrivée d’air chaud, un four ou tout autre appareil (notamment les amplificateurs) produisant de la chaleur.

9. Veillez à profiter de la sécurité offerte par les fiches de type terre ou polarisées. Les fiches polarisées sont équipées de deux bornes de largeurs différentes. Les fiches de type terre sont équipées de deux bornes et d’un orifice pour la mise à la terre. Ces deux types de dispositifs ont pour but d’assurer votre sécurité. Si la prise fournie ne s’adapte pas à votre prise de courant, consultez un électricien pour qu’il remplace cette prise obsolète.

10. Protégez le cordon d’alimentation contre les risques de piétinement ou de pincement, notamment au niveau des fiches, des prises de courant et des branchements à l’appareil.

11. Utilisez uniquement les accessoires spécifiés par le fabricant.

12. Utilisez uniquement le chariot, le support, le trépied, l’équerre ou la table spécifié(e) par le fabricant ou vendu(e) avec l’appareil. Si vous utilisez un chariot, faites attention à ne pas faire basculer l’ensemble chariot/appareil.

Français Installation et instructions de sécurité Page 7

pro.Bose.com Informations importantes pour la sécurité

13. Débranchez cet appareil pendant les orages ou en cas d’inutilisation prolongée, afin d’éviter de l’endommager.

14. Confiez toute réparation à du personnel qualifié. Une réparation est nécessaire lorsque l’appareil a été endommagé de quelque façon que ce soit (endommagement du cordon d’alimentation ou de la fiche électrique, renversement d’un liquide ou de tout objet sur l’appareil, exposition de l’appareil à la pluie ou à l’humidité, mauvais fonctionnement, chute de l’appareil, etc.). Ne tentez pas de réparer ce produit vous-même. L’ouverture ou la dépose d’un couvercle risque de vous exposer à des tensions électriques ou autres dangers. Veuillez contacter Bose pour connaître les coordonnées du centre de réparation agréé le plus proche.

15. Pour éviter tout risque d’incendie ou d’électrocution, ne surchargez pas les prises murales, les rallonges ou les prises multiples.

16. Ne laissez jamais d’eau ou d’objets pénétrer à l’intérieur du produit : des éléments sous tension pourraient être touchés ou il pourrait se produire un court-circuit susceptible d’entraîner un incendie ou un risque d’électrocution.

17. Consultez les marquages de sécurité sous le boîtier du produit.

18. L’écran du panneau d’affichage LCD est illuminé lorsque le produit est alimenté. Si le produit est alimenté et que l’écran LCD n’est pas allumé, veuillez faire réviser l’appareil.

19. Veillez à ne pas utiliser l’appareil à une température supérieure à 40 °C. Gardez à l’esprit le fait que la température à l’intérieur d’un rack fermé peut être très supérieure à la température ambiante.

Ce produit est conforme à toutes les directives de la Communauté Européenne qui s’y appliquent. L’attestation complète de conformité est disponible à l’adresse www.Bose.com/compliance.

Ce symbole signifie que le produit ne doit pas être jeté avec les déchets ménagers, mais doit être déposé dans un centre de collecte approprié pour recyclage. La mise au rebut adéquate et le recyclage permettent de protéger les ressources naturelles, la santé humaine et l’environnement. Pour plus d’informations sur l’élimination et le recyclage de ce produit, contactez votre mairie, votre service d’enlèvement des ordures ou le magasin où vous avez acheté ce produit.

Ce produit répond aux critères d’immunité des directives EN 55103-2 pour les appareils de classe E2.

Courant d’appel à la mise sous tension : 14,8 A (230 V / 50 Hz)

Courant d’appel après une interruption de 5 secondes de l’alimentation secteur : 15,4 A (230 V / 50 Hz)

Informations sur les produits générateurs de bruit électrique (Notice de conformité FCC pour les USA)

Remarque : ce matériel a fait l’objet de tests prouvant sa conformité aux limites imposées aux appareils numériques de classe A, conformément à la partie 15 des réglementations de la FCC. Ces limites sont conçues pour offrir une protection raisonnable contre les interférences nuisibles lorsque l’appareil est utilisé en environnement commercial. Cet appareil génère, utilise et est susceptible d’émettre de l’énergie à certaines fréquences radio. À ce titre, s’il n’est pas installé ou utilisé conformément aux instructions, il est susceptible de perturber les communications radio. L’utilisation de cet équipement dans une zone résidentielle risque de provoquer des interférences nuisibles, auquel cas l’utilisateur devra remédier au problème à ses propres frais.

Ce produit est conforme aux spécifications CAN ICES-3 (A) /NMB-3 (A).

Wichtige Sicherheitshinweise pro.Bose.com

Seite 8 Installations- und Sicherheitshinweise Deutsch

WARNUNG: Dieses Produkt darf nur von fachkundigen Monteuren installiert werden.

Vielen Dank, dass Sie Bose® PowerMatch®-Verstärker für Ihr Klangverstärkungssystem gewählt haben. Dieses Dokument soll fachkundigen Monteuren grundlegende Installations- und Sicherheitsrichtlinien für Bose PowerMatch-Verstärker in typischen Festinstal-lationssystemen bieten. Bitte lesen Sie dieses Dokument vor der Installation durch.

WARNUNG: Schützen Sie das Gerät vor tropfenden oder spritzenden Flüssigkeiten, und stellen Sie keine mit Flüssigkeiten gefüllten Gefäße (z. B. Vasen) auf das Gerät oder in die Nähe des Geräts. Wie bei allen elektronischen Geräten dürfen niemals Flüssigkeiten ins Innere gelangen. Dadurch kann es zu Fehlfunktionen und/oder Bränden kommen.

WARNUNG: Um Brände und Stromschläge zu vermeiden, darf dieses Gerät keinem Regen ausgesetzt werden.

WARNUNG: Stellen Sie keine brennenden Kerzen oder ähnliches auf das Gerät oder in die Nähe des Geräts.

WARNUNG: Berühren Sie keine nicht isolierten Kabel oder Kabelklemmen. Die Audiokabelanschlüsse dieses Produkts sind spannungs-führend und können Verletzungen verursachen.

Hinweis: Das Produkt ist nicht für den Einsatz im Freien geeignet. Verwenden Sie den Verstärker nur innerhalb von Gebäuden und nicht in Campingfahrzeugen, auf Booten o. ä.

Das Blitzsymbol mit Pfeilspitze in einem gleichseitigen Dreieck weist den Benutzer auf das Vorhandensein einer nicht isolierten gefährlichen elektrischen Spannung innerhalb des Systemgehäuses hin, durch die die Gefahr von Stromschlägen besteht. Berühren Sie die Ausgangsanschlüsse nicht, wenn der Verstärker eingeschaltet ist. Schalten Sie alle Anschlüsse am Verstärker aus.

Das Ausrufezeichen in einem gleichseitigen Dreieck, wie es am System angebracht ist, soll den Benutzer auf wichtige Bedienungs- und Wartungsanweisungen in dieser Installationsanleitung aufmerksam machen.

ACHTUNG: Nehmen Sie keine Veränderungen am Verstärker oder am Zubehör vor. Nicht autorisierte Veränderungen können die Sicherheit, die Erfüllung von Richtlinien und die Systemleistung beeinträchtigen.

ACHTUNG: Dieses Produkt muss an eine Steckdose mit Erdungsschutz angeschlossen werden.

ACHTUNG: Falls Sie den Netzstecker verwenden, um das Gerät von der Stromversorgung zu trennen, sollten Sie sicherstellen, dass Sie jederzeit auf den Stecker zugreifen können.

Wichtige Sicherheitshinweise1. Lesen Sie die folgenden Anweisungen.

2. Bewahren Sie diese Anweisungen auf – zum späteren Nachschlagen.

3. Beachten Sie alle Warnhinweise – am Produkt und in der gesamten Produktdokumentation.

4. Befolgen Sie alle Anweisungen.

5. Verwenden Sie dieses Gerät nicht in der Nähe von Wasser oder Feuchtigkeit.

6. Reinigen Sie das Gerät nur mit einem sauberen, trockenen Tuch.

7. Achten Sie darauf, dass die Lüftungsöffnungen nicht blockiert sind. Stellen Sie das Gerät nur in Übereinstimmung mit den Herstelleranweisungen auf. Stellen Sie das Gerät an einem Ort auf, an dem gute Ventilation gewährleistet ist, um den zuverlässigen Betrieb des Geräts sicherzustellen und es gegen Überhitzung zu schützen.

8. Stellen Sie das Gerät nicht in der Nähe von Wärmequellen auf, wie Heizkörpern, Wärmespeichern, Öfen oder anderen Geräten (auch Verstärkern), die Wärme erzeugen.

9. Beeinträchtigen Sie in keiner Weise die Schutzfunktion des Schutzkontaktsteckers. Ein gepolter Stecker hat zwei Stromkontakte, von denen einer breiter als der andere ist. Ein Schutzkontaktstecker hat zwei Stromkontakte und einen dritten Erdungskontakt. Der dritte Kontakt dient der Sicherheit. Falls der mitgelieferte Stecker nicht in Ihre Steckdose passt, wenden Sie sich an einen qualifizierten Elektriker, um die Steckdose auszutauschen.

10. Verlegen Sie das Netzkabel so, dass es keine Stolpergefahr darstellt und nicht beschädigt werden kann – insbesondere im Bereich von Steckern und Steckdosen und dort, wo das Netzkabel aus dem Gerät herausgeführt wird.

11. Verwenden Sie nur Zubehör-/Anbauteile, die vom Hersteller zugelassen sind.

Deutsch Installations- und Sicherheitshinweise Seite 9

pro.Bose.com Wichtige Sicherheitshinweise

12. Verwenden Sie für das Gerät nur Rollwagen, Ständer, Dreibeine, Halterungen oder Tische, die vom Hersteller zugelassen sind oder zusammen mit dem Gerät verkauft werden. Falls Sie einen Rollwagen verwenden, dürfen Sie die Einheit Gerät/Rollwagen nur mit Vorsicht bewegen, damit Verletzungen beim möglichen Umkippen ausgeschlossen sind.

13. Ziehen Sie den Netzstecker des Geräts während eines Gewitters oder wenn Sie das Gerät längere Zeit nicht benutzen – zur Vermeidung von Schäden am Produkt.

14. Wenden Sie sich bei allen Reparatur- und Wartungsarbeiten nur an qualifiziertes Kundendienstpersonal. Wartungsarbeiten sind in folgenden Fällen nötig: Bei jeglichen Beschädigungen wie z. B. des Netzkabels oder Netzsteckers, wenn Flüssigkeiten oder Gegenstände in das Gehäuse gelangt sind, das Gerät Regen oder Feuchtigkeit ausgesetzt wurde, fallen gelassen wurde oder nicht ordnungsgemäß funktioniert. Versuchen Sie nicht, dieses Produkt selbst zu warten. Öffnen oder entfernen Sie unter keinen Umständen die Gehäuseabdeckungen, da Sie andernfalls mit gefährlichen elektrischen Spannungen in Berührung kommen oder anderen Gefahren ausgesetzt sein könnten. Wenden Sie sich telefonisch an Bose, um die Anschrift eines autorisierten Kundendienstzentrums in Ihrer Nähe zu erfragen.

15. Vermeiden Sie Gefahren durch Brände oder elektrische Schläge, indem Sie Steckdosen, Verlängerungskabel und integrierte Gerätesteckdosen nicht überlasten.

16. Lassen Sie keine Flüssigkeiten oder Fremdkörper in das Gerät gelangen – diese können unter gefährliche elektrische Spannung gesetzt werden oder Bauteile kurzschließen und folglich Brände und Stromschläge auslösen.

17. Beachten Sie die Sicherheitshinweise auf dem Gehäuse.

18. Der LCD-Bildschirm auf der Vorderseite leuchtet, wenn das Produkt Strom erhält. Wenn Strom anliegt und der LCD-Bildschirm nicht leuchtet, geben Sie das Gerät bitte zur Reparatur.

19. Achten Sie darauf, dass die Betriebstemperatur des Geräts 40 °C nicht überschreitet. Seien Sie sich aller Bedingungen in einem geschlossenen Rack bewusst, welche zu einem Anstieg der Temperatur über Zimmerniveau führen können.

Dieses Produkt entspricht allen Anforderungen der geltenden EU-Richtlinien. Die vollständige Konformitätserklärung ist einsehbar unter www.Bose.com/compliance.

Dieses Symbol bedeutet, dass das Produkt nicht mit dem Hausmüll entsorgt werden darf, sondern bei einer geeigneten Sammelstelle für das Recycling abgegeben werden muss. Die ordnungsgemäße Entsorgung und das Recycling tragen dazu bei, die natürlichen Ressourcen, die Gesundheit und die Umwelt zu schützen. Weitere Informationen zur Entsorgung und zum Recycling dieses Produkts erhalten Sie von Ihrer zuständigen Kommune, Ihrem Entsorgungsdienst oder dem Geschäft, in dem Sie dieses Produkt gekauft haben.

Dieses Produkt erfüllt die Anforderungen an die Störfestigkeit der Klasse E2 der Richtlinie EN55103-2.

Anfänglicher Einschaltstrom: 14,8 A (230 V/50 Hz)

Einschaltstrom nach 5 Sekunden Unterbrechung des Netzanschlusses: 15,4 A (230 V/50 Hz)

Informationen über Produkte, die elektrisches Rauschen verursachen (Hinweis zur FCC-Einhaltung für die USA.)

Hinweis: Dieses Gerät wurde geprüft. Es stimmt mit den Regelungen für Geräte der Klasse A gemäß Teil 15 der FCC-Vorschriften überein. Diese Grenzwerte sollen einen angemessenen Schutz gegen elektromagnetische Störungen beim Betrieb in gewerblicher Umgebung gewährleisten. Dieses Gerät erzeugt und verwendet Hochfrequenzstrahlung und kann sie auch aussenden. Daher verursacht das Gerät, wenn die Installation und Benutzung nicht in Übereinstimmung mit dieser Bedienungsanleitung erfolgt, möglicherweise Störungen des Funkverkehrs. Beim Betrieb dieses Geräts in Wohngebieten können erhebliche Störungen des Funkverkehrs verursacht werden. Eventuell daraus entstehende Kosten trägt allein der Benutzer des Geräts.

Dieses Produkt erfüllt CAN ICES-3 (A)/NMB-3 (A).

Page 10 Installation and Operating Guide English

Contents pro.Bose.com

Introduction .................................................................................................................................................... 11

Product Features .......................................................................................................................................... 11

PowerMatch® Amplifier Line Overview ................................................................................................. 12

PowerMatch configurable professional power amplifiers ...................................................................... 12

Onboard Loudspeaker Processing and Front Panel Interface ............................................................... 12

Accessory Cards .................................................................................................................................... 12

Ideal for use with RoomMatch® array module loudspeakers .................................................................. 12

Interfacing with ControlSpace® engineered sound processors .............................................................. 12

Controls, Display, and Connectors ......................................................................................................... 13

Hardware Installation .................................................................................................................................. 14

Unpacking............................................................................................................................................... 14

Ventilation ............................................................................................................................................... 14

AC Mains Outlet Requirements .............................................................................................................. 14

Making Connections ................................................................................................................................... 15

Connection and Configuration Steps ..................................................................................................... 15

Power (Mains) Connection ...................................................................................................................... 15

Standby Mode ........................................................................................................................................ 15

Wiring Input Connectors ......................................................................................................................... 16

Wiring Output Connectors ...................................................................................................................... 16

Fault Notification Output ........................................................................................................................ 18

Serial over Ethernet ................................................................................................................................ 18

Setup and Configuration ........................................................................................................................... 19

Configuration Methods ........................................................................................................................... 19

Control Panel Description ....................................................................................................................... 20

Front Panel Control Menu Structure ....................................................................................................... 21

Control Menu Descriptions ..................................................................................................................... 21

Setting the Limiting Function for use with 3rd Party Loudspeakers ....................................................... 33

Sample Output Configurations for Different Loudspeaker Loads ............................................... 34

Configuration of a RoomMatch® Two-Module Array (Example 1) ........................................................... 34

Configuration of a RoomMatch RMS215 Subwoofer Module (Example 2) ............................................ 34

Maintenance Operations ........................................................................................................................... 35

Updating Firmware and Speaker EQ Presets ......................................................................................... 35

Saving and Recalling Amplifier Settings (USB-only version amplifiers) ................................................. 36

Saving and Recalling Amplifier Settings (network version amplifiers) .................................................... 36

About the Alarm Log and Fault Indicator ................................................................................................ 37

Troubleshooting ............................................................................................................................................ 38

Appendix ......................................................................................................................................................... 39

Interface Comparison Table .................................................................................................................... 39

Technical Specifications - Common to all PowerMatch® models ........................................................... 40

Technical Specifications - PM8500 / PM8500N ..................................................................................... 41

Technical Specifications - PM8250 / PM8250N .................................................................................... 42

Technical Specifications - PM4500 / PM4500N .................................................................................... 43

Technical Specifications - PM4250 / PM4250N ..................................................................................... 44

AC Current Draw and Thermal Dissipation Information ......................................................................... 45

English Installation and Operating Guide Page 11

pro.Bose.com Installation and Operating Guide

IntroductionThank you for choosing Bose® PowerMatch® configurable professional power amplifiers.

PowerMatch® power amplifiers deliver concert-quality sound for a wide variety of fixed-installation sound reinforcement systems and provide class-leading efficiency, sound quality, and reliability.

Two documents are available to assist with amplifier installation and configuration. This document delivers detailed installation and standalone configuration information. A separate document, the ControlSpace® Designer™ Software Guide (downloadable from pro.Bose.com), provides detailed instructions on how to use ControlSpace Designer software to fully configure, monitor, and update PowerMatch amplifiers. For network version amplifiers, Designer software provides additional network setup, control, and monitoring capabilities.

Information furnished in these guides is intended to help professionals install and set up the product, but does not include all details of design, production, or variations of equipment. Nor does it cover every possible situation that may arise during installation, operation, or maintenance. If assistance is required beyond the scope of these documents, please contact your local Bose Representative or Technical Support specialist.

Product Features• PowerMatch amplifier series

Four amplifier models provide multiple channel and power options to satisfy the needs of almost any audio installation. Models include options for 4 or 8 channel versions and 250 or 500 watt per channel power levels. Additionally, network versions add control and monitoring functionality over standard Ethernet networks.

• Dual Feedback Loop SystemProprietary design combines Class-D efficiency with a dual current and voltage feedback loop circuit that continuously monitors and controls both the current and voltage delivered to the loudspeaker load. This combination allows the amplifier to consistently deliver the widest possible dynamic range, frequency response, and lowest possible distortion, independent of power level and load impedance.

• QuadBridge™ Output ConfigurationEach loudspeaker output terminal can be configured as Mono, V-Bridge, I-Share or Quad, allowing the total available power of the amplifier bank to be allocated to one or more output channels. V-Bridge and Quad modes can drive either low-impedance or 70/100V loads. Configuration of the loudspeaker output can be accessed from either the front panel of the amplifier or using ControlSpace Designer software.

• PeakBank™ Power SupplyRegenerative 4-quadrant power supply with fast-tracking Power Factor Correction (PFC) supports high efficiency while delivering sustainable and repeatable low frequency response.

• Integrated DSPA configurable fixed-architecture DSP provides multiple EQ stages, crossovers, delays, limiters, and matrix mixing. While PowerMatch can drive nearly any loudspeaker for the installed sound market, pre-loaded loudspeaker EQs and limiting presets for Bose loudspeakers provide an additional layer of simplified setup and premium sound. Amplifier models PM8500 and PM4500 feature power levels and array EQ features ideal for use with RoomMatch® array module loudspeakers and subwoofers.

• ControlSpace® Designer™ Software SetupAll models offer front panel USB connectivity for Bose ControlSpace Designer software programming, with network versions adding Ethernet network setup, control, and monitoring.

• Front Panel User InterfaceCombined front panel LCD and user controls provide useful visual information and access to a subset of amplifier settings suffi-cient for basic amplifier output configuration and status/fault monitoring. A convenient panel lock can be set to prevent access to unauthorized users.

• Network Control and MonitoringNetwork versions support a set of remote monitoring and fault reporting capabilities via the rear panel RJ45 Ethernet connection and Bose ControlSpace Designer software. A fault reporting and control protocol using Serial over Ethernet allows third party control and monitoring systems to communicate easily with one or many PowerMatch amplifiers.

• Load Sweep ToolUsing ControlSpace Designer software, the amplifier can measure the load impedance of each low impedance-configured output for system diagnostic and documentation purposes. The load measurement can be stored inside the amplifier and recalled as a reference curve for future comparisons to determine if the system is still operating as expected.

• Digital Expansion SlotOptional digital cards expand the input capabilities of PowerMatch® amplifiers, enabling the amplifiers to receive digital audio from Bose ESPLink-equipped devices and popular digital audio networks.

• Auto-Standby / Auto-WakeEnergy saving feature that allows PowerMatch amplifiers to automatically go into a lower power Standby Mode when audio signal falls below a set threshold, and wake up when audio signal is above threshold. All parameters, including time and audio detection levels are adjustable from within ControlSpace® Designer™ software.


Installation and Operating Guide pro.Bose.com

PowerMatch® Amplifier Line OverviewPowerMatch configurable professional power amplifiers

PowerMatch multi-channel power amplifiers are highly efficient, reliable and configurable. Four amplifier models provide channel and power options for most fixed-installation audio systems. Each model offers front panel USB connectivity for full access to settings using ControlSpace® Designer™ software. Network versions of each amplifier feature a rear panel RJ45 connector, allowing network setup, control, and remote monitoring of one or more PowerMatch amplifiers using ControlSpace Designer software and standard network equipment.

Onboard Loudspeaker Processing and Front Panel Interface

All amplifier models share the same onboard loudspeaker processing and front panel interface but vary in channel count, power, and Ethernet connectivity.

The following table summarizes the key differences between the PowerMatch amplifier models:

PowerMatch Amplifier Models Total Rated Power Channels (max.) Output Connectors Recommended AC Mains Circuit IEC Power Cord

PM8500 / PM8500N 4000 watts 8 2 20A (120 V) or 16A (230 V) C19




Accessory Cards

PowerMatch amplifiers feature a digital expansion slot for accessory plug-in cards. These cards allow for added I/O flexibility. For example, the Bose® PM ESPLink card provides a shared 8-channel uncompressed digital audio bus between one or more PowerMatch units and a ControlSpace ESP engineered sound processor. Visit pro.Bose.com for additional information and to view the latest list of PowerMatch accessory cards.

Accessory Card Product Code

PowerMatch Dante™ network card PC 359844-0020

PowerMatch CobraNet® card PC 345975-0110

PowerMatch ESPLink digital input card PC 349898-0110

PowerMatch AES3 input card PC 638301-0010

Ideal for use with RoomMatch® array module loudspeakers

RoomMatch loudspeakers connect and configure easily to PM8500 and PM4500 amplifiers. Built-in loudspeaker and array EQs together with suitable output power ratings and optimized loudspeaker limiting/protection make these amplifiers ideal for use in designs with RoomMatch array module loudspeakers.

Interfacing with ControlSpace® engineered sound processors

PowerMatch amplifiers are designed to be used independently or in any system with most professional audio processing equipment and loudspeakers. However, there are unique advantages to using PowerMatch with Bose ControlSpace ESP engineered sound processors. These processors enable multi-channel input options, mixing, routing, processing, and distribution capabilities – all using a single configuration tool, ControlSpace Designer software.

Using a Bose ESPLink connection, a ControlSpace ESP engineered sound processor can route 8 digital audio channels to multiple PowerMatch amplifiers for low latency in-rack audio distribution. For wiring digital audio between racks or for use in larger distributed systems, Audio over Ethernet expansion cards are also available for use with the PowerMatch and ControlSpace ESP processors.

Dante is a trademark of Audinate Pty Ltd.CobraNet is a registered trademark of Cirrus Logic, Inc.



Controls, Display, and Connectors

Figures 1 and 2 detail the various elements found on the front and rear panels of PowerMatch® amplifiers.

Figure 1. Front Panel View

1 32

456

7 8

8

1 LED Indicators 5 Menu Soft Keys (1-5)

2 LCD Screen 6 USB connector

3 Navigation Soft Key 7 Front airflow intake vents

4 Rotary Encoder 8 Front rack-mount ears

Figure 2. 4-channel and 8-channel Rear Panel Views

16A

9A

18 12 139 10 11 14 15 16 17 18

9 Analog Input connectors 14 Loudspeaker output connectors

10 Fault Notification Output 15 AC Mains receptacle

11 Ethernet RJ-45 network connector (Network versions only)

16 AC Mains retention clip

12 Rear airflow exhaust vents 17 Power Switch/Resettable Circuit Breaker

13 Digital expansion card slot cover 18 Rear rack-mount support tabs



Hardware InstallationUnpacking

The product carton includes the following items:

Figure 3. Carton contents

PowerMatch® amplifier Installation and Operating Guide Detachable IEC power cord

Connector Accessory Pack (contents vary according to model number):

PowerMatch modelsInput

connectorsOutput

connectorsShorting jumpers

Fault connector

Plastic wire tie-wraps Accessory Kit PN

PM8500, PM8500N8 2 4 1 9 343511-0010

PM8250, PM8250N

PM4500, PM4500N4 1 2 1 5 343511-0020

PM4250, PM4250N

Rack Mounting

PowerMatch amplifiers are designed to fit standard 19-inch (48 cm) rack equipment, occupying 2 rack-units (RU) in height, requiring a mounting depth of 21 inches (53 cm) from the front rack rail. Use four fasteners with washers (not supplied) to mount the amplifier front panel rack ears to the equipment rack rails. Rack-mount tabs are also provided on the rear of the chassis to secure the amplifier using rear rack mount ears (not provided). Rear rack mounting is recommended in cases when pre-assembled racks with amplifiers are trans-ported to installation venues.

Ventilation

PowerMatch amplifiers are designed to operate under a wide range of conditions, with continuous operation up to 104° F (40° C) ambient temperature. To ensure safe operation, the front and rear airflow vents should never be blocked. Air flows into the front of the unit and exits the rear vents. The internal fans automatically increase speed when the amplifier is generating more heat. Should the unit exceed safe operating temperature, a gradual reduction of gain will automatically be applied for thermal protection. If the automatic gain reduction does not reduce operating temperatures to safe conditions, the unit will mute all outputs and the red FAULT LED will illuminate on the front panel.

AC Mains Outlet Requirements

PowerMatch amplifiers feature an efficient, universal switch-mode power supply with fast-tracking Power Factor Correction (PFC) and can operate with AC mains line voltages from 100 to 240 volts at 50/60 Hz. With typical music program material, amplifier model PM8500 provides full rated power from a single 20-amp, 120V (common in USA) AC mains outlet, or single 16-amp, 230V (common in Europe) mains outlet. The mains circuit requirement for models PM8250, PM4500, and PM4250 is lesser, as full rated power can be achieved using a 15-amp, 120V (USA) AC mains outlet or a 10-amp, 230V (Europe) AC mains outlet.

High-power amplifiers draw large amounts of current from the AC mains. Use of extension cords to power the amplifier could introduce significant impedance and a resulting voltage drop on the mains that may interfere with normal operation of the amplifier.

In countries like Japan where 100V AC mains are used, the following guidelines will be helpful to ensure optimal performance:

• Ensure a minimum of 100V AC at the amplifier plug when the amplifier is idle.• Use a dedicated mains circuit for each amplifier.• Locate the amplifiers as close as possible to the mains outlet.• If used, extension cords should be 14 AWG (2 mm2) or larger, and less than 6.6 ft (2 m) in length.



Making ConnectionsConnection and Configuration Steps

Use the following procedure when setting up a PowerMatch® amplifier for the first time.

1. Install any digital expansion cards (optional)

2. Mount the amplifier into the rack

3. Connect power cable and retaining clip

4. Turn on amplifier

5. Enable Standby Mode from the front panel of the amplifier (See page 29.)

6. Configure amplifier (use front panel or ControlSpace® Designer™ software)

7. Wire input connection from source device(s)

8. Wire output connectors to speakers

9. Disable Standby Mode

10. Connect Fault Notification Output to management system or device (optional)

11. Clear alarms (See page 30.)

12. Test system

Power (Mains) Connection

Power connection is made using the included IEC power cord. The amplifier also includes a retaining clip to help secure the power connection to the amplifier. To install, place the retaining clip toward the center of the amplifier, plug in the IEC power cord, then swing the retaining clip so it locks behind the IEC connector.

Figure 4. IEC Connector retaining clip in place.

Standby Mode

Enabling Standby Mode decouples the amplifier section from the loudspeaker output. In this state the product also consumes less power. Standby Mode can be entered manually from the front panel using the following steps:

MAIN MENU > UTILITY > STANDBY MODE > press ENTER STANDBY

While in Standby, front panel options and loudspeaker output configurations can be changed without directly affecting the loudspeaker load.

Standby Mode can be automatically entered and exited using the Auto-Standby/Auto-Wake function as a method to help reduce energy usage during times when audio is not required. Refer to the ControlSpace Designer Software Guide for details on this feature.



Wiring Input Connectors

The balanced line-level analog inputs utilize 3-pin terminal block connectors (Phoenix Contact® #1776168, supplied). Terminal descrip-tions are printed directly on the connectors for convenience. For balanced inputs, strip the wire ¼ inch (6 mm) and connect to the respective positive, negative, and ground terminals as indicated on the connector and in Figure 5. Tinned wires are not recommended. For unbalanced inputs, the connector should be wired with the negative and ground/shield terminals, connected with a jumper wire (not supplied). To reduce the occurrence of ground loop noise, it is recommended that the input cable shield be joined with the ground terminal at only one device - at the source output connector or at the amplifier input connector. You can use the supplied tie-wraps to help secure the input cables.

Figure 5. Balanced and unbalanced connectors (jumper not supplied)

Positive terminalNegative terminalGround terminal

Balanced connection Unbalanced connection

Wiring Output Connectors

PowerMatch® amplifiers feature QuadBridge™ technology which provides the flexibility to reconfigure each amplifier output. On a single output connector, amplifier power can be allocated between 1 and 4 output channels for low impedance loudspeaker loads or up to 2 output channels for high impedance (70V and 100V) loudspeaker loads. A combination of high/low impedance loads and a mix of power levels can be configured through the front panel interface or using ControlSpace® Designer™ software. The following table describes the behavior of the four available output modes:

Mode Description

Mono Each channel operates independently, and will drive 2 to 16 Ω loads

V-Bridge Channel pairs are combined to deliver 2x voltage and will drive high impedance (70V or 100V) and 4 to 8 Ω loads

I-Share Channel pairs are combined to deliver 2x current, and will drive 2 Ω loads

Quad Two channel pairs are combined to deliver 2x voltage and 2x current while driving high impedance (70V or 100V) or 4 Ω loads

4-channel amplifiers (PM4500, PM4250) use a single loudspeaker output connector. 8-channel amplifiers (PM8500, PM8250) split total amplifier power across two output connectors. In the case of the PM8500 which has a maximum rated power of 4000 watts, power is split where 2000 watts is available at each output connector.

Each loudspeaker output utilizes a high-current, 8-pin locking terminal block connector (Phoenix Contact® COMBICON® Part #1778120, supplied) that accept cables from 10 to 24 AWG (5.3 - 0.2 mm2) in diameter.

Note: Use Class 2 wiring for speaker connections.

To wire the output connector:

1. Strip the insulation off each speaker wire to expose 3/8" (10 mm) of bare conductor.

2. Insert each wire into the correct terminal on the block connector. Use a small Phillips size 1 (or appropriate) screwdriver to secure the wire.

3. Firmly press the block connector into the receptacle on the amplifier until the left and right latches snap into place.

To detach the block connector from the amplifier, slide the two orange release tabs toward the amplifier to release the locking tabs. Once released, pull the terminal block connector from the amplifier.

Warning: While the amplifier does self-protect under most improper output conditions, misconfiguration of loudspeaker mode and incorrect connection of loudspeakers could damage connected loudspeakers and/or amplifier.

COMBICON is a registered trademark of Phoenix Contact GmbH & Co.Phoenix Contact is a registered trademark of Phoenix Contact GmbH & Co.



The following chart shows examples of the types of loads possible with the required output mode:

Loudspeaker Load Output Mode Channel Sharing PM8500 PM8250 PM4500 PM4250

2 - 8 Ω Mono (Low-Z) None 500 W @ 4 Ω 250 W @ 4 Ω 500 W @ 4 Ω 250 W @ 4 Ω

4 - 8 Ω V-Bridge (Low-Z) Half block 1000 W @ 8 Ω 500 W @ 8 Ω 1000 W @ 8 Ω 500 W @ 8 Ω

70V V-Bridge (70V) Half block 800 W @ 70V 400 W @ 70V 800 W @ 70V 400 W @ 70V

100V V-Bridge (100V) Half block 1000 W @ 100V 500 W @ 100V 1000 W @ 100V 500 W @ 100V

2 Ω, high power I-Share (Low-Z) Half block 1000 W @ 2 Ω 500 W @ 2 Ω 1000 W @ 2 Ω 500 W @ 2 Ω

4 Ω, high power Quad (Low-Z) Full block 2000 W @ 4 Ω 1000 W @ 4 Ω 2000 W @ 4 Ω 1000 W @ 4 Ω

70V, high power Quad (70V) Full block 1600 W @ 70V 800 W @ 70V 1600 W @ 70V 800 W @ 70V

100V, high power Quad (100V) Full block 2000 W @ 100V 1000 W @ 100V 2000 W @ 100V 1000 W @ 100V

Note: Configure the output mode of the amplifier before connecting loudspeakers. See page 21 for details on front panel configu-ration. Carefully follow the proper connection method for the selected output configuration.

The wiring of the connector varies by amplifier output configuration. The output terminal assignments for Mono (single channel) and V-Bridge configurations are printed on the rear panel of the amplifier.

The following graphics illustrate wiring examples for the different output configuration modes. Mixed combinations of Mono, V-Bridge, and I-Share modes are possible from one output block.

Figure 6. Output wiring showing the four basic configurations

Mono mode V-Bridge mode

I-Share mode Quad mode

Note: Changing the output configuration may automatically place the unit in Standby Mode to allow the safe installation of loudspeaker cable connections to the rear panel output terminal blocks.

Note: While not optimal, a 70/100V loudspeaker load can be driven off a single channel in Mono mode but is limited to 50 V RMS / 71 V Peak capability. Download the application note “Using Mono Mode to Drive High Impedance Loudspeaker Loads” from pro.Bose.com for details on how to adjust software and tap settings for this derated use.



Fault Notification Output

Each PowerMatch amplifier features a hardware fault notification circuit. This circuit drives a normally open or normally closed contact closure (1A, 30 VDC maximum). The fault output, using the orange-colored 3-pin terminal block (Phoenix Contact® #1976010, supplied), is intended to provide an external connection to a remote system monitor for fault notification purposes. Terminal assignments are printed directly on the connector as shown in Figure 7. See “About the Alarm Log and Fault Indicator” on page 37 for details on trapped faults and how to filter reported faults.

Figure 7. Fault Notification output connector

Normally closedCommonNormally open

Serial over Ethernet

Network version amplifiers can leverage the Ethernet connector to communicate serial data with control systems and devices. Commands are available to read and set Standby Mode status, and to read the output configuration. For interfacing with third party control systems, the amplifier is also able to read and set the amplifier to broadcast alarms, fault events, and changes to the Fault Output state when they occur.

A full listing of the available protocol can be found in the PDF document "ControlSpace® Serial Control Protocol" on pro.Bose.com.



Setup and ConfigurationFigure 8 shows the basic signal flow and available DSP functions available to manipulate each individual input channel.

Some functions and advanced parameters can only be modified using ControlSpace® Designer™ software. See “Interface Comparison Table” on page 39 to view configurations required to access functions and features.

Figure 8. Simplified DSP block diagram (8-channel diagram shown; 4-channel models are similar)

Configuration Methods

There are three methods to configure a PowerMatch® amplifier for use. The table below shows those methods and describes function-ality differences between the methods.

Method of Configuration Use Case

Local front panel Fast, easy access to status, basic loudspeaker processing and control options.

USB connection to ControlSpace Designer software • Full-featured control and visibility over all DSP functions. • Graphical tools available to help create EQs for 3rd party loudspeakers, real time

display and monitoring. • Multiple network version amplifiers can be configured and monitored from a single

PC using an RJ45 Ethernet connection (use shielded CAT5e cable only).

RJ45 connection to ControlSpace Designer software (network versions only)3



Control Panel Description

Figure 9. PowerMatch® Front Panel

1

10 11

98765

4

3

2

1Fault LED Indicator LED lights red when a fault condition has been detected. For more information see Figure 18, “Fault Conditions” on page 37.

2Clip LED Indicator Indicates red when the input signal reaches full scale. Bose recommends that you reduce input levels or modify input sensitivity settings

to prevent this condition. (See Input Sensitivity on Page 24).

3Limit LED Indicator When this LED illuminates, indicates that one or more output channels have reached user-adjustable RMS or Peak threshold values or

that system internal protection is occurring.

4Signal LED Indicator Flashes with the presence of input signal.

5Hardware Name / Menu Depth Displays the name (either default or assigned) given to this amplifier. This can be changed using ControlSpace® Designer™ software.

While navigating menus, indicates current menu location and depth.

6Meters While at the operating screen (shown), each channel shows the status and level of its output. Muted channels show MUTE in the bar

and combined channel modes show grouped bars as shown above with channels 1-4 and channels 5-6. Output meters automatically change display width to correspond to the active output configuration.

7IP Address / Device ID Shows the IP address (network versions only) or device ID number (USB-only models). Setting can be modified using ControlSpace

Designer software.

8Navigation Indicator Indicates which menu level will be actuated when the Navigation Soft Key is pressed.

9Navigation Soft Key Actuates the menu level as indicated by the Navigation Indicator.

10 Menu Soft Keys (1-5) Selects various options that appear on the LCD screen directly above these controls.

11 Rotary Encoder This spin/press control wheel allows scrolling and selection of items shown in lists.



Front Panel Control Menu Structure

The displays and user controls accessible by the front panel are presented in the following menu structure illustration:

Figure 10. Front panel menu structureOPERATING

Mute All

MAIN MENU

LEVELMETERDSPCONFIGUTILITY

DSP

Speaker PresetsArray EQDelayLimiting

LEVEL

Input SourceInput SensitivityInput MuteOutput MuteOutput Attenuate

METER

Input MeterOutput Volltage

CONFIGURE UTILITY

Standby modeAlarm LogNetwork Setup (Device ID)Lock Front PanelSet Front Panel Lock CombinationDisplayRestore Factory SettingsFirmware Version

* PM4500 and PM4250 models only

Control Menu Descriptions

The following tables describe each menu item and the various options available to the user from the front panel. Front panel screens from the PM8500N amplifier are shown which are indicative of both the PM8500 and PM8250 models. Models PM4500 and PM4250 screens will be similar and simplified over the 8-channel models.

OPERATING

OPERATING

Mute All

Description This is the default operating display for the amplifier.

Shows the amplifier name, IP Address/ Device ID and current output configuration. In this case, channels 1-4 are running in Quad mode, channels 5 and 6 are in V-Bridge (or I-Share mode), and channels 7 and 8 are running independently in Mono modes. The level shown is -40dB to 0dB full scale.

Available Controls Navigation Soft Key: Enters MAIN MENU.

Menu Soft Key #5: Mutes/Unmutes ALL output channels.



MAIN MENU

MAIN MENU

LEVELMETERDSPCONFIGUTILITY

Description The MAIN MENU offers five areas of control:

• Level• Meter• DSP• Configuration• Utility

Available Controls Navigation Soft Key: Back to OPERATING display.

• Menu Soft Key #1: Enters LEVEL menu.• Menu Soft Key #2: Enters METER Menu.• Menu Soft Key #3: Enters DSP Menu.• Menu Soft Key #4: Enters CONFIG Menu.• Menu Soft Key #5: Enters UTILITY Menu.

Notes Network version amplifiers have the option to select the mode of "Power Up" state, whether to restore last settings or revert to project file settings on power up. Selectable from the amplifier properties page in ControlSpace® Designer™ software, the "Restore Last Settings" state is disabled by default for network version amplifiers. Due to the standalone nature of USB-only amplifiers, front panel changes are usually intentional and should be recalled on subsequent power-ups.

MAIN MENU < LEVEL

LEVEL


Description The LEVEL menu allows access to the input and output level and type parameters.

Available Controls Navigation Soft Key: Back to MAIN MENU.

Menu Soft Key #1-5: Changes menu to respective category.

Rotary Encoder: Scrolls and selects menu options.

Options Input SourceInput SensitivityInput Mute Output Mute Output Attenuate

MAIN MENU < LEVEL < INPUT SOURCE

LEVEL


Description This display allows you to select an analog or digital audio source for each input channel. No parameters can be modified if the amplifier is without a digital input card.

Available Controls To access Input Source, use the rotary encoder dial from the LEVEL menu to highlight, then press to select.

Navigation Soft Key: Back to LEVEL menu.

Rotary Encoder: On 8-channel models, allows the scrolling of two pages of four input channels.

Menu Soft Key #5: Toggles between forcing all channels to be Analog and all channels to be Digital. For amplifiers without an input card installed, the inactive button caption reads “Analog only.”

Menu Soft Key #1-4: Toggle between input type analog or digital for each displayed channel.

Options “Ana” (Analog), “Dig” (Digital).

Notes Options only available when a digital expansion card is installed.



MAIN MENU < LEVEL < INPUT SENS

LEVEL


Description This display allows you to appropriately match each configured input channel to the incoming signal. This per channel setting corresponds to the level that will create rated power out of the amplifier, with all other gains through the DSP signal processing chain set to 0 dB (unity gain). For best noise performance use the highest setting you can, keeping peaks of the input signal as close to the sensitivity level as you can without exceeding it.

Real-time output is displayed and affected by changing the sensitivity level.

Available Controls To access Input Sensitivity, use the rotary encoder dial from the LEVEL menu to highlight, then press to select.


Menu Soft Key #5: Enables the scrolling of four pages of two input channels using the rotary encoder.

Menu Soft Key #1 and #3: Enables the respective input channel to be selected. Use the rotary encoder to select sensitivity values in dBu.

Options +0.0 dBu, +4.0dBu, +12dBu, +24dBu

MAIN MENU < LEVEL < INPUT MUTE

LEVEL


Description This display allows you to mute each input channel.

Available Controls To access Input Mute, use the rotary encoder dial from the LEVEL menu to highlight, then press to select.


Rotary Encoder: Continuously scrolls through two input channel pages, allowing users to access Input A-D, and on 8-channel models, Input E-H.

Menu Soft Key #1-4: Toggles the mute state for each channel listed above each button.

Menu Soft Key #5: Enables/disables muting of all channels.

Options Mute enabled/disabled per channel.Mute ALL enabled/disabled for all channels.

Notes All input channels can also be muted from the MAIN MENU < METER < INPUT display.

MAIN MENU < LEVEL < OUTPUT MUTE

LEVEL


Description This display allows each configured output channel to be muted. For channels set to output modes other than Mono, as in the case shown with channels 1-4 above, muting control is bound by the configured groupings.

Available Controls To access Output Mute, use the rotary encoder dial from the LEVEL menu to highlight, then press to select.

Navigation Soft Key: Back to LEVEL MENU.

Rotary Encoder: Scrolls through output channels as displayed under the eight indicator boxes (8-channel models only).

Menu Soft Key #1-4: Toggles the mute state for each channel listed above each button. Note that some keys may not have channels listed.

Menu Soft Key #5: Enables/disables muting of all channels.

Options Mute enabled/disabled per channel.

Mute ALL enabled/disabled for all channels.

Notes Output channels can also be (all) muted from the MAIN MENU and MAIN MENU < METER < OUTPUT VOLTS screens.



MAIN MENU < LEVEL < OUTPUT ATTEN

LEVEL


Description This display allows you to attenuate each configured output channel. For channels set to output modes other than Mono, attenuation control is bound by the configured groupings. Two output channels are displayed at one time. Real time output is displayed and affected by changing attenu-ation.

Available Controls To access Output Atten, use the rotary encoder dial from the LEVEL menu to highlight, then press to select.


Menu Soft Key #5: Enables channel navigation using the rotary encoder.

Menu Soft Key #1 and #3: Enables the respective output channel to be selected. Use the rotary encoder to select attenuation values in dB.

Options -60dB to 0dB in increments of 0.5dB.

MAIN MENU < METER

METER


Description The METER menu allows you to view the status of both input and output channels.

Available Controls Navigation Soft Key: Back to LEVEL menu.



Options Output VoltageInput Meter

MAIN MENU < METER < INPUT

METER


Description This display allows you to monitor each input channel. You can also mute all input channels.

Available Controls To access the Input Meter, use the rotary encoder dial from the METER menu to highlight, then press to select.

Navigation Soft Key: Back to METER menu.

Menu Soft Key #5: Enables/disables muting of all output channels.

Options Mute ALL, Unmute ALL.



MAIN MENU < METER < OUTPUT VOLTS

METER


Description This display allows you to monitor each configured output channel voltage. For channels set to output modes other than Mono, metering is bound by the configured groupings. You can also mute all output channels.

Available Controls To access Output Voltage, use the rotary encoder dial from the METER menu to highlight, then press to select.

Navigation Soft Key: Back to METER menu.

Menu Soft Key #5: Enables/disables muting of all output channels.

Options Mute ALL, Unmute ALL.

MAIN MENU < DSP

DSP


Description The DSP menu allows you to apply sophisticated digital signal processing to the signal chain.

Available Controls Navigation Soft Key: Back to MAIN MENU.



Options Speaker PresetsArray EQDelayLimiting

Notes Further DSP functions and product features are available using ControlSpace® Designer™ software. See “Interface Comparison Table” on page 26 for the complete list of available functionality.

MAIN MENU < DSP < SPEAKER PRESETS

DSP


Description This display allows you to apply Bose® loudspeaker preset EQs to each amplifier output. Scroll bars for speaker series and speaker families help indicate the relative position of the current selection in each list.

Available Controls To access the Speaker Presets, use the rotary encoder dial from the DSP menu to highlight, then press to select.

Navigation Soft Key: Back to DSP menu.

Menu Soft Key #5: Enables the selection of the output channel (or output groupings) using the rotary encoder dial.

Menu Soft Key #1: Enables users to select from a list of Bose speaker series, or none, using the rotary encoder. Once the desired series is highlight-ed, press the rotary encoder to select.

Menu Soft Key #3: Enables users to select from within the list of speaker families. Once the desired speaker is highlighted, press the rotary encoder to select.

Options Series: NONE, FreeSpace®, LT, Panaray®, RoomMatch®, Custom.Model: Flat, Corresponding Bose loudspeakers, Custom user EQ curves.



MAIN MENU < DSP < ARRAY EQ

DSP


Description This display allows you to apply additional EQ to each input channel that feeds signal to RoomMatch® loudspeakers in array configurations.

Available Controls To access Array EQ, use the rotary encoder dial from the DSP menu to highlight, then press to select.


Menu Soft Key #5: Enables the selection of the input channel (or output groupings) using the rotary encoder dial.

Menu Soft Key #1: Enables the selection of RoomMatch modules within the array. Use the rotary encoder to adjust this parameter.

Menu Soft Key #2: Enables the total vertical angle of the array, in degrees, to be set. Use the rotary encoder to adjust this parameter.

Menu Soft Key #3: Enables Array EQ to be turned ON or OFF. Use the rotary encoder to toggle the desired state.

Options Modules: 2, 3, 4, 5, 6, 7, 8V Angle: 20 to 100 degrees in 5-degree incrementsArray EQ ON, Array EQ OFF

MAIN MENU < DSP < DELAY

DSP


Description This display allows delay to be applied to each loudspeaker output.

Available Controls To access Delay, use the rotary encoder dial from the DSP menu to highlight and press to select.



Menu Soft Key #1: Enables the selection of delay values, which are listed in meters, feet, milliseconds, and microseconds. Each press of this key changes the highlighted unit/quantity. Secondarily, changing units allows for increased control of the delay range step size - when METERS is highlighted, coarse control is possible while uSEC affords fine control. Use the rotary encoder to adjust the selected parameter.

Menu Soft Key #4: Enables delay to be turned ON or OFF. Use the rotary encoder to toggle the desired state.

Options Delay time from 0 to 3000 milliseconds per output channel, increments dependant on selected delay unit/quantityDelay ON, Delay OFF



MAIN MENU < DSP < LIMITING

DSP


Description This display allows you to adjust limiting parameters that allow for loudspeaker driver protection for each output channel.

Available Controls To access Limiting, use the rotary encoder dial from the DSP menu to highlight, then press to select.



Menu Soft Key #1: Enables the selection of a peak voltage value, which corresponds to the maximum voltage that may be applied to the driver without causing over-excursion. Use the rotary encoder to adjust the selected parameter.

Menu Soft Key #2: Enables the selection of an RMS voltage threshold value, which works in conjunction with the subsequent attack and release values. The RMS voltage setting corresponds to the long-term power handling capability of the loudspeaker. Use the rotary encoder to adjust the selected parameter.

Menu Soft Key #3: Enables the selection of attack time, in milliseconds, related to the RMS limiter. Use the rotary encoder to adjust the selected parameter.

Menu Soft Key #4: Enables the selection of release time, in milliseconds, related to the RMS limiter. Use the rotary encoder to adjust the selected parameter.

Options PEAK: 0.5 to 200 Volts (dependant on output mode), 0.5 V incrementsRMS: 0.5 to 100 Volts (dependant on output mode), 0.5 V incrementsATTACK: From 500 to 10,000 millisecondsRELEASE: From 500 to 10,000 milliseconds

Notes Values are automatically applied for Bose® loudspeakers set in MAIN MENU < DSP < SPEAKER PRESETS.For non-Bose loudspeakers, refer to manufacturer technical specifications for information to properly configure the limiter.See “Setting the Limiting Function for use with 3rd Party Loudspeakers” on page 33 for further details.

MAIN MENU < CONFIGURE

CONFIGURE

Description The CONFIGURE menu allows you to access the configuration of input and output signals for a particular system design.

Available Controls Navigation Soft Key: Return back to MAIN MENU.



Options Output ConfigInput Routing

MAIN MENU < CONFIGURE < DIGITAL INPUT RANGE

CONFIGURE

Description On 4-channel models (PM4500, PM4250), a group of channels from expansion cards card can be mapped to input channels A-D.

Available Controls "To access Digital Input Range, use the rotary encoder dial from the CONFIGURE menu to highlight, then press to select. Navigation Soft Key: Back to CONFIG menu. Menu Soft Key #1 and 2: Selects a range of digital input channels for access by the amplifier."

Options [1-4], [5-8]

Notes Amplifier models PM4500 and PM4250 are input channel limited to four analog and/or four digital channels. For additional flexibility, 8-channel feeds from the digital expansion slot have been grouped into 4-channel banks for selective use in installations with multiple 4-channel PowerMatch® amplifiers.



MAIN MENU < CONFIGURE < INPUT ROUTING

CONFIGURE

Description This display allows you to assign a mix of input signals to each of the output channels.

Available Controls To access Input Routing, use the rotary encoder dial from the CONFIGURE menu to highlight, then press to select.

Navigation Soft Key: Back to CONFIG menu.

Rotary Encoder: Scrolls through output channels.

Menu Soft Key #5: Enables the selection of two input channels pages. Use the rotary encoder dial to toggle between input channel groupings A-D or E-H (8-channel models).

Menu Soft Key #1-4: Enables the selection of one of the displayed input channels. A second press of the soft key will toggle between states “OFF” and a user-adjustable gain value. Once an input channel is highlighted and showing a gain value, use the rotary encoder wheel to dial the desired amount of signal to be applied to the displayed channel.

OFF, -60dB to 0dB in 1dB increments

Notes Bose suggests that you first configure output modes (MAIN MENU < CONFIG < OUTPUT CONFIG) before performing input routing.

MAIN MENU < CONFIGURE < OUTPUT CONFIG

CONFIGURE

Description This display allows you to configure the output section of the amplifier for various output modes.

Available Controls To access Output Configuration, use the rotary encoder dial from the CONFIGURE menu to highlight, then press to select.

Note: The amplifier must be off-line from ControlSpace® Designer™ software before making any output configuration changes.

Navigation Soft Key: Back to CONFIG menu.


Menu Soft Key #1: Enables the selection of an output configuration for the displayed output channel. Use the rotary encoder to adjust the selected parameter. Once the desired mode is highlighted, press the rotary encoder to select.

Options For Channels 1 and 2

Mono (Low-Z)Ch1+2 V-Bridge (Low-Z)Ch1+2 V-Bridge (70V)Ch1+2 V-Bridge (100V)Ch1+2 I-Share (Low-Z)Ch1+2+3+4 Quad (Low-Z)Ch1+2+3+4 Quad (70 V)Ch1+2+3+4 Quad (100 V)

For Channels 3 and 4

Mono (Low-Z)Ch3+4 V-Bridge (Low-Z)Ch3+4 V-Bridge (70V)Ch3+4 V-Bridge (100V)Ch3+4 I-Share (Low-Z)Ch1+2+3+4 Quad (Low-Z)Ch1+2+3+4 Quad (70 V)Ch1+2+3+4 Quad (100 V)

For Channels 5 and 6 (8-channel models only)

MONOCh5+6 V-Bridge (Low-Z)Ch5+6 V-Bridge (70V)Ch5+6 V-Bridge (100V)Ch5+6 I-Share (Low-Z)Ch5+6+7+8 Quad (Low-Z)Ch5+6+7+8 Quad (70 V)Ch5+6+7+8 Quad (100 V)

For Channels 7 and 8 (8-channel models only)

MONOCh7+8 V-Bridge (Low-Z)Ch7+8 V-Bridge (70V)Ch7+8 V-Bridge (100V)Ch7+8 I-Share (Low-Z)Ch5+6+7+8 Quad (Low-Z)Ch5+6+7+8 Quad (70 V)Ch5+6+7+8 Quad (100 V)

Notes Selection of channels will display modes that offer possible combined channels available only to those respective channels.



MAIN MENU < UTILITY

UTILITY


Description The UTILITY menu allows you to access additional configuration parameters of the amplifier.

Available Controls Navigation Soft Key: Return back to MAIN MENU.



Options Standby ModeAlarm LogNetwork Setup (network versions) / Device ID (USB-only versions)Lock Front PanelSet Front Panel Lock CombinationDisplayRestore Factory SettingsFirmware Version

Notes Further utility and monitoring options are available using ControlSpace® Designer™ software. See “Interface Comparison Table” on page 30 for the complete list of available functionality.

MAIN MENU < UTILITY < STANDBY

UTILITY


Description This display allows you to safely disable all amplifier output channels. This feature is helpful when changing speaker output connec-tions while maintaining amplifier power on.

Available Controls To access the Standby Mode, use the rotary encoder dial from the UTILITY menu to highlight, then press to select.

Navigation Soft Key: Back to UTILITY menu.

Rotary Encoder: Scrolls through output channels.

Menu Soft Key #1: Enables amplifier output channels (exit Standby Mode).

Menu Soft Key #5: Disables amplifier output channels (enter Standby Mode).

Options Exit Standby, Enter Standby

Notes The messaging on the screen will display the current state of this mode: “Not in Standby” or “In Standby.”



MAIN MENU < UTILITY < ALARM LOG

UTILITY


Description This display allows you to view, clear, and erase the last 50 captured alarm notifications.

Available Controls To access ALARM LOG, use the rotary encoder dial from the UTILITY menu to highlight, then press to select.


Menu Soft Key #5: Enables the rotary encoder dial to scroll through the alarm log.

Menu Soft Key #1: Clears the alarm indicated by the FAULT LED on the front panel.

Menu Soft Key #3: Erases all entries captured in the alarm log. A confirmation screen is presented by which users can confirm (Soft Key #1) or cancel (Soft Key #5).

Options Clear Alarm, Erase Log, Scroll.

Notes ControlSpace® Designer™ software allows you to configure and view additional information about alarm and fault conditions.

MAIN MENU < UTILITY < NETWORK SETUP (network versions)

UTILITY


Description This display allows you to set the network IP address of the amplifier.

Available Controls To access Network Setup, use the rotary encoder dial from the UTILITY menu to highlight, then press to select.


Menu Soft Key #1: Enables the rotary encoder dial to toggle between DHCP or FIXED IP address mode. Push the rotary encoder to enable the selection. A confirmation screen is presented by which users can confirm (Soft Key #1) or cancel (Soft Key #5). Upon confirmation, the unit will save and reboot using the new setting.

Menu Soft Key #2-5: Enables the rotary encoder dial to adjust the value of each IP address octet. Once the IP address has been fully modified, push the rotary encoder to enable the selection. A confirmation screen is presented by which users can confirm (Soft Key #1) or cancel (Soft Key #5). Upon confirmation, the unit will save and reboot using the new setting.

Options Mode: DHCP, FixedIP Address Octet Values: 0 to 255

Notes DHCP is enabled by default on network version amplifiers. Upon Power Up, resolving of DHCP times out after 10 seconds to IP:80 for PM8500N/PM8250N and IP:40 for PM4500N/PM4250N.

MAIN MENU < UTILITY < DEVICE ID (USB-only versions)

UTILITY


Description This display allows you to set the device identification number of the amplifier.

Available Controls To access Device ID Setup, use the rotary encoder dial from the UTILITY menu to highlight, then press to select.


Rotary Encoder: Use the dial to scroll through device ID values. Push the rotary encoder to set the new device ID. A confirmation screen is presented by which users can confirm (Soft Key #1) or cancel (Soft Key #5).

Options Device ID Number: 1-255



MAIN MENU < UTILITY < LOCK FRONT PANEL

UTILITY


Description This display allows you to view the current unlock combination and ability to lock the front panel controls to prevent tampering.

Available Controls To access Lock Front Panel, use the rotary encoder dial from the UTILITY menu to highlight, then press to select.


Rotary Encoder: Press the rotary encoder to set the front panel lock.

Options Lock now

Notes Once locked, users accessing the rotary encoder or any of the soft keys are prompted with an unlock screen by which the combina-tion previously shown in MAIN MENU < UTILITY < LOCK FRONT PANEL must be entered to regain access to the Main Menu.Users that have misplaced a combination and are locked out can use ControlSpace® Designer™ software to connect, unlock the front panel, and view a previously assigned lock combination.

MAIN MENU < UTILITY < LOCK COMBINATION

UTILITY


Description This display allows you to set the front panel lock combination.

Available Controls To access Set Front Panel Combination, use the rotary encoder dial from the UTILITY menu to highlight, then press to select.


Menu Soft Key #1-5: Enables each of the five digits to be selected and modified by using the rotary encoder dial.

Options 0–9 for digits 1–5.

MAIN MENU < UTILITY < DISPLAY

UTILITY


Description This display allows you to set the display intensity.

Available Controls To access the Display menu, use the rotary encoder dial from the UTILITY menu to highlight, then press to select.


Menu Soft Key #1: Sets the display backlight intensity to “Normal” or bright.

Menu Soft Key #2: Sets the display backlight intensity to “Dim” or low.

Options Normal, Dim



MAIN MENU < UTILITY < RESTORE FACTORY

UTILITY


Description This display allows you to erase all settings and return the amplifier options to the state set by the factory.

Available Controls To access the Restore Factory Settings menu, use the rotary encoder dial from the UTILITY menu to highlight, then press to select.


Menu Soft Key #1: Begins the process to restore the amplifier settings to factory condition. A confirmation screen is presented by which users can confirm (Soft Key #1) or cancel (Soft Key #5).

Options Restore

Notes Invoking Restore Factory Settings will change the "power on state" of the amplifier such that all front panel setting changes will be saved and recalled on each subsequent power up. This state can be modified using ControlSpace® Designer™ software.

MAIN MENU < UTILITY < FIRMWARE VERSION

UTILITY


Description This display allows you to view the model number, hardware software versions, installed Bose® loudspeaker EQ presets file, and status of any plug-in cards.

Available Controls To access the Firmware Versions menu, use the rotary encoder dial from the UTILITY menu to highlight, then press to select.




Setting the Limiting Function for use with 3rd Party Loudspeakers

The Limiting function allows you to restrict, per channel, the maximum signal level to the loudspeaker. Here are some simplified steps to aid in setting the limiter function.

1. Locate the technical data specification sheet for the 3rd party loudspeaker.

2. Configure the amplifier outputs (MAIN MENU < CONFIG < OUTPUT CONFIG) to drive the loudspeaker at or beyond the rated power of the loudspeaker indicated in the loudspeaker’s data specification sheet.

3. Select the proper EQ (flat or custom EQ for non-Bose loudspeakers) from MAIN MENU < DSP < SPEAKER PRESETS.

4. Using the manufacturer’s loudspeaker specification sheet, calculate the limiter RMS voltage using the loudspeaker's continuous power rating using the following formula:

RMS Voltage = Square Root (rated power of the loudspeaker x loudspeaker impedance).

5. In the MAIN MENU < DSP < LIMITING menu, select the appropriate output channel and set the RMS voltage to the loudspeaker’s RMS voltage.

6. Set the Peak value to 1.4 to 2 times the RMS voltage. Note the maximum RMS and Peak voltage values below in Figure 11 when setting these parameters.

7. Reference loudspeaker data specifications or consult with loudspeaker manufacturer to obtain optimal settings for Attack and Release parameters.

Figure 11. Output Channel Limiter Maximum Voltage Values

Mode Peak RMS V

Mono 71 V 50 V

I-Share 71 V 50 V

V-Bridge 142 V 100 V

Quad 142 V 100 V



Sample Output Configurations for Different Loudspeaker Loads

For reference, the following two examples illustrate two different output configurations using RoomMatch® array module loudspeakers with PM8500 or PM4500 amplifiers. Front panel configuration settings are provided. While not covered in this documentation, ControlSpace® Designer™ software provides additional configurability to these examples. Further information on this software can be found on pro.Bose.com.

Configuration of a RoomMatch® Two-Module Array (Example 1)

In this example, two full-range RoomMatch array modules are connected to one PowerMatch® amplifier, arranged as follows:

(2) Bose® RoomMatch 7010 array module loudspeakers (70° H x 10° V)

(1) Bose PowerMatch PM4500 configurable professional power amplifier (PM8500 amplifier similar)

Figure 12. RoomMatch two-module array configuration

Note: All RoomMatch loudspeaker connections use Neutrik® NL4 speakON-type cable connectors. Please refer to RoomMatch loudspeaker documentation for further details.

Front Panel Configuration Menu Settings:

1. MAIN MENU < CONFIG < OUTPUT CONFIG

Set the output configuration for channels 1-4 to MONO mode.

2. MAIN MENU < DSP < SPEAKER PRESETS

For channels 1 and 3 set SERIES to “RoomMatch” and MODEL to “RM_Array LF.”

For channels 2 and 4 set SERIES to “RoomMatch” and MODEL to “RM_Array HF.”

3. MAIN MENU < DSP < ARRAY EQ

For each input channel that is routed to an output channel, set the MODULES value to 2 and the V-Angle parameter to 20 degrees, which is the total vertical angle of the shown modules. Ensure that the state of the Array EQ is set to ON.

Configuration of a RoomMatch RMS215 Subwoofer Module (Example 2)

In this example, one subwoofer module is connected to one PowerMatch amplifier, arranged as follows:

(1) Bose RoomMatch RMS215 subwoofer

(1) Bose PowerMatch PM8500 configurable professional power amplifier

Figure 13. RoomMatch subwoofer configuration

Front Panel Configuration Menu Settings:

1. MAIN MENU < CONFIG < Output Config

Set the output configuration for channels 1+2 and 3+4 to V-Bridge (Low-Z) mode.

2. MAIN MENU < DSP < Speaker Presets

For channels 1+2 and 3+4, set SERIES to “RoomMatch” and MODEL to “RMS215.”

Neutrik is a registered trademark of Neutrik AG



Maintenance OperationsUpdating Firmware and Speaker EQ Presets

Each PowerMatch® amplifier contains two user-updatable files: Firmware and loudspeaker EQ files. These files can both be updated from ControlSpace® Designer™ software using a PC connected to either the USB connection on the front panel of the amplifier, or, in the case of a network version amplifier, an Ethernet network connection (use shielded CAT5e cable only).

The firmware version of the amplifier can be viewed directly on the front panel by selecting MAIN MENU < UTILITY < FIRMWARE VERSIONS. The version of both firmware and EQ files can be viewed in ControlSpace Designer software.

Please refer to the ControlSpace Designer software user’s guide available on pro.Bose.com for software installation instructions.

From within ControlSpace Designer software, firmware and EQ file information can be found in the Hardware Manager. To launch this feature, click Hardware Manager in the System Menu or click the Hardware Manger button in amplifier properties window.

Figure 14. Launching the Hardware Manager

Upon launching the Hardware Manager, the software performs a scan to determine the devices on the network and adds them to the Device List. Select the Firmware Update tab (Figure 15) to view the firmware file status, and select the EQ Update tab (Figure 16) to view EQ file status. If a file is out-of-date, select the device and click the Update button.

Figure 15. Firmware Update window



Figure 16. EQ Update window

Note: Between timed releases of ControlSpace® Designer™ software, PowerMatch® firmware updates and loudspeaker EQ files may become available. Check pro.Bose.com for updates and instructions on how to load and apply these files.

Saving and Recalling Amplifier Settings (USB-only version amplifiers)

You can save amplifier settings using a PC, USB connection, and ControlSpace Designer software. This may be useful for archiving settings made on the front panel after installation. You may also find it useful to copy settings from one PowerMatch amplifier to other PowerMatch amplifiers.

To save front panel settings:

1. Install ControlSpace Designer software on a compatible PC.

2. Connect the PC to the amplifier using USB.

3. Start ControlSpace Designer.

4. The amplifier should automatically connect and populate into the Project Window.

5. Save the Project File by selecting File -> Save As… from the menu bar.

To replace front panel settings with a previously saved filed:

1. Start ControlSpace Designer.

2. Open the previously saved Project File by selecting File -> Open from the menu bar.

3. Connect the PC to the amplifier using USB.

4. Click the YES button when presented with a dialog box asking, “Go Online via USB?”

5. Click “Send to Device” in the Settings Transfer window (Figure 17) to push the settings to the connected amplifier.

Figure 17. Settings Transfer window

Saving and Recalling Amplifier Settings (network version amplifiers)

With any network version amplifier, you can save and update device settings within a networked system with one or more amplifiers. This process is outside the scope of this guide. Refer to the ControlSpace Designer software documentation for details.



About the Alarm Log and Fault Indicator

The PowerMatch® amplifier monitors operating temperature, power supply status, amplifier status, open and short wiring, and additional conditions for issues.

When issues are detected, the last 50 issues are stored in the amplifier in an internal log found by accessing MAIN MENU < UTILITY < ALARM LOG from the front panel.

Information from the alarm log can also be viewed using ControlSpace® Designer™ software. In systems where ControlSpace Designer software is actively connected, either via USB or Ethernet, the time and date of the alarm condition is appended to the alarm log entry on the PC. Locally stored alarm information has no time/date information, but is shown in order of last occurrence.

Critical internal system-related issues are always considered faults and will trigger the fault-notification output and the Fault LED on the front panel. However, you have the ability to select whether certain conditions are faults using ControlSpace Designer software. Refer to the ControlSpace Designer software documentation for details on how to view and manage alarms.

The table below lists the possible fault conditions and recommendations on how to address these conditions. Variables are shown as "x", X", or "y", but will be displayed as values or part numbers in the actual alarm text string.

Figure 18. Fault Conditions

Customer Serviceable Warnings and Alarms

Fault Text Suggestions for Resolution

Internal protection applied on Channel x Amplifier approaching operating/thermal limit on channel x, gain reduced, self-clearing fault. Optional alarm condition in ControlSpace Designer.

Limiting applied on Channel x Limiting was applied on output x, self-clearing when signal level lowers.

Open detected on Channel x Check loudspeaker and cabling for open circuit on output x.

Clipping on Channel x Reduce input signal channel x.

AC loss detected/AC returned Installation activity noticed. Clear error and check again. If continued error, check for AC mains voltage sag or change to new circuit.

Digital Audio Input loss detected No issue, self-clearing. Check digital audio input connections.

large parallel Vdiff on ch x Shorting jumpers not installed properly.

short on ch x Check loudspeaker and cabling for short circuit on output x. Cycle Power.

ext digital clk out of range, using internal clk Reinsert accessory card, reboot amplifier. Replace card if error continues.

no proc table loaded Software error, restore factory defaults.

Power supply temperature above max allowed Amplifier signal should be reduced, check ambient temp of rack.

Amp x temperature above max allowed Amplifier signal should be reduced, check ambient temp of rack.

pwr supply temp above max Amplifier signal should be reduced, check ambient temp of rack.

amp x temp above max Amplifier signal should be reduced, check ambient temp of rack.

fuse saver indicates circuit breaker near limit Amplifier signal should be reduced, check ambient temp of rack. Check mains for low voltage.

FET temp above max Amplifier signal should be reduced, check ambient temp of rack.

too much I^2t on ch x Amplifier signal should be reduced, check ambient temp of rack.

pwr supply rail below min Check mains supply for low line voltage. Change circuit.

EHF detected on ch x Check loudspeaker and cabling for short circuit on output x. Cycle Power.

Non-Customer Serviceable Warnings and Alarms

Fault Text Resolution

Both amp or PS fan fail Requires Bose® Support. Call Bose Representative.

Power supply fault ICV not OK

power supply fault DC not OK

power supply fault DC_200 not OK

power supply fault AC_line not detected

Flash memory fault

DSP boot failure

System Halted

audio disabled: DSP I2C error on VI meas ADC ch x

audio disabled: DSP I2C error on DAC ch x

audio disabled: DSP I2C error on EHF for amp x

no ADC input



Non-Customer Serviceable Warnings and Alarms

Fault Text Resolution

DSP processing resources exceeded Requires Bose® Support. Call Bose Representative.

ADC XXXXXX on input board I2C err

ADC XXXXXX on digital board I2C err

ADC XXXXXX amp x I2C err

DAC XXXXXX amp x (x&x) I2C err

XXXXXXX(EHF) amp x I2C err

XXXXXXX(temp) amp x I2C err

XXXXXXX(PS) I2C err

Troubleshooting

Problem Possible Solution

No power • Turn on power switch. Clip, Limit, and Signal LEDs should stay lit for approximately the first 15 seconds, after which the amplifier should be fully ready for operation. The amplifier’s LCD screen will show the firmware version screen after about 10 seconds, then revert to the operating screen.

• Check power cable, ensure retaining clip is in place. • Check mains circuit.

Power is on, but no sound Check the LCD screen for output meter activity. If no signal activity, check the following:

• Check the Input Meter screen for presence of signal. If no signal, fix source or cabling.• Ensure that input and output signals are not muted. • Check that Input Routing is configured properly.• Check that Input Source is set to appropriate signal type (analog or digital).• Check that Output Attenuate is not set too low.• Make sure loudspeakers are wired correctly to output connectors.• Check that Output Configuration is set correctly.• Check that Standby Mode is not active.

Power is on, sound is low • Verify source level by monitoring Input Meter. Check that Input Routing and Input Sensitivity are set for optimal gain.• Check that Output Attenuate is not set too low.• Make sure loudspeakers are wired correctly to output connectors.• Check that Output Configuration is set correctly.• Check that Limiting parameters are set properly.

Unnatural sound Check that all DSP functions (EQs, Limiter, Band Pass, Delay) are set appropriately.

Front panel is locked out, combination is lost Use ControlSpace® Designer™ software to connect to the amplifier and unlock the front panel.

Fault LED is lit Refer to Figure 18, “Fault Conditions” on page 37 for alarm conditions and potential solutions. Call your local Bose® Support contact for assistance with unlisted or unsolvable faults.

USB is connected to PC but not found by ControlSpace Designer software

• Unplug/replug USB connector.• Uninstall ControlSpace Designer software, download the latest version, reinstall.• Restart PC, try again.• Try another USB port on the computer.• Try another USB cable.• Check ControlSpace Designer software documentation for more details.

Ethernet is connected to network but amplifier is not found by ControlSpace Designer software (PowerMatch network versions only)

• Check the IP address of the PowerMatch® amplifier.• Ensure that there is not another device with the same address on the network.• Ensure ControlSpace Designer is connected to the same subnet as the PowerMatch amplifier.• Try another shielded CAT5e cable.• Launch a Windows Command prompt window (cmd.exe) and enter the text "ping" followed by the IP address of the

amplifier at the command prompt then press enter key. This should result in four successful replies from the amplifier.



AppendixInterface Comparison Table

Function Front Panel Interface

ControlSpace® Designer software

Set input sensitivity (dBu) X X

Set input gain (dB) X X

Set input mute X X

View input level (dB) X X

Set output attenuation (dB) X X

Set output mute X X

View output gain (dB) X X

View output voltage (V) X X

Load Bose® speaker EQ preset X X

View Bose speaker EQ X X

Load speaker array EQ X X

Adjust delay X X

Adjust limiting X X

Modify output configuration X X

Modify input routing X X

Enter/exit standby mode X X

View alarm log X X

Clear alarm X X

Erase alarm log X X

Set DHCP or Fixed IP network address X X

Lock front panel X X

Set front panel combination X X

Adjust display contrast X X

Restore factory presets X X

View firmware version X X

Update firmware version X X

Update speaker EQ files X X

Adjust/view input channel 5-Band PEQ X

Adjust/view advanced parameters for Array EQ X

Use of signal generator X

Adjust/view Bandpass Filters X

Adjust/view advanced parameters for Speaker EQ X

Use of Limiter Meters X

Use of Link Groups X

Per channel fault and limit indicators X

Set Auto-Standby parameters X

Wake from Auto-Standby X X

Set input type (analog vs digital) X X

Setup of alarm conditions X

Measure/save/compare loudspeaker impedances X

Local Monitor Mode X

Network Monitor Mode X

Configure and monitor multiple amplifiers X

Backup/restore amplifier configuration state X



Technical Specifications - Common to all PowerMatch® models

Audio Performance Specifications 1

Frequency Response 20 Hz - 20 kHz (@ 1 W and +/- 0.5 dB)

Signal-to-Noise Ratio, Analog Input > 102 dB (PM8500 and PM4500), > 99 dB (PM8250 and PM4250), below rated power, A-weighted

THD < 0.4 % (at 1 W, 20 Hz to 20 kHz)

Intermod Distortion - SMPTE < 0.4 % (60 Hz, 7 kHz)

Channel Separation (Crosstalk) > 65 dB (adjacent channels, at 1 kHz)

Damping Factor > 1000 (10-1000 Hz, 4 ohms, at amplifier output)

Integrated DSP

A/D and D/A Converters 48 kHz / 24-bit

Total Latency (Analog In - Amp Out) < 0.95 ms

Input to Output Signal Routing 8 x 8 matrix (PM8500 and PM8250), 4 x 4 matrix (PM4500 and PM4250)

Loudspeaker Presets Bose Professional

Input EQ 5-band PEQ (+/- 20 dB), notch, shelving, high pass, low pass

Bandpass Filters (Crossover) Butterworth, Bessel, or Linkwitz-Riley, up to 48 dB/octave

Loudspeaker EQ 9-band PEQ (+/- 20 dB), shelving, high pass, low pass, 2-band RoomMatch® array EQ

Maximum Output Delay 3 s

Output Limiter Peak and RMS voltage

Indicators and Controls

LED Status Indicators Signal, limit, clip, fault

User Interface Controls Mute, input sensitivity, output attenuation, EQ on/off, preset select. 240 x 64 LCD. Additional controls available w/ ControlSpace® Designer™ software

General

Setup and Configuration Software ControlSpace Designer software V3.2 or greater

PC Interface Connection USB (Network version adds Ethernet RJ45)

Fault Notification Output NC/NO Relay Contact (1 A, 30 VDC), 3-pin Phoenix Contact® connector (orange color; part # 1976010)

(1) Measured at +24 dBu sensitivity unless otherwise specified.



Technical Specifications - PM8500 / PM8500N

Power Rating 1 2 Ω 4 Ω 8 Ω 70 V 100 V

THD for Power Rating, Typical < 0.1 % < 0.1% < 0.1% 1% 1%

Mono Mode 450 W 500 W 300 W See footnote 3 See footnote 3

V-Bridge Mode 450 W 2 1000 W 1000 W 800 W 1000 W

I-Share Mode 1000 W 500 W 2 300 W 2 Not available Not available

Quad Mode 1000 W 2 2000 W 1000 W 2 1600 W 2000 W

Maximum Rated Power 4000 W (total all channels)

Peak Output Voltage 71 / 142 V (Mono / V-Bridge, I-Share, and Quad modes)

Voltage Gain 33 / 36 / 33 / 36 dB (Mono / V-Bridge / I-Share / Quad modes)

Audio Inputs Analog Digital (Optional Card)

Input Channels 8 (balanced line level) 8

Input Impedance > 100 kΩ N/A

Sensitivity 0, +4, +12, +24 dBu, selectable Digital: 0, -12, -20, -24 dBFS, selectable

Maximum Input Level +24 dBu (at 24 dBu sensitivity setting) N/A

Connectors, Input 3-pin Phoenix Contact® (green color; part # 1776168) Card Dependent

Audio Outputs

Output Channels 2 to 8 configurable

Connectors, Output 8-pin Phoenix Contact connectors (part # 1778120), supports 10-24 AWG wire

Electrical Specification

Mains Voltage 100-240 V (50/60 Hz)

Mains Circuit Recommendation 20A (120 V) or 16A (230 V)

Mains Connector IEC 60320-C20 (Inlet)

Minimum AC Line Voltage 80 V (reduced output power)

Maximum Inrush Current 15.4 A (230 VAC, 50 Hz)

Maximum RMS Current Draw 15 A

Efficiency, 1/3 Rated Power > 75 % (pink noise input signal, typical)

Output Stage Topology Class-D

Overload Protection High temperature, DC, HF, short, voltage limiter, current limiter, inrush current, mains circuit breaker protection

Physical

Dimensions 3.5" H x 19" W x 20.7" D (88 mm x 483 mm x 525 mm) - EIA-310 standard width, 2RU height

Net Weight 28.4 lb (12.9 kg)

Shipping Weight 34.5 lb (15.7 kg)

Mounting Depth 21" (533 mm)

Operating Temperature 32 °F - 104 °F (0 °C - 40 °C)

Cooling System Microprocessor-controlled, variable-speed fans, front to rear airflow

(1) Output power is measured per channel, all channels driven, using test signals at 1 kHz.

(2) Configuration not recommended / not optimal.

(3) Limited use available. Tap 70V loudspeakers 2x the desired power. Tap 100V loudspeakers 4x the desired power. Refer to the application note “Using MONO Mode to Drive High Impedance Loudspeaker Loads.”




Power Rating 1

2 Ω 4 Ω 8 Ω 70 V 100 V





Quad Mode 1000 W 2 1000 W 500 W 2 800 W 1000 W





Input Channels 8 (balanced line level) 8





Audio Outputs


Connectors, Output 8-pin Phoenix Contact®connectors (part # 1778120), supports 10-24 AWG wire











Physical













Power Rating 1

2 Ω 4 Ω 8 Ω 70 V 100 V





Quad Mode 1000 W 2 2000 W 1000 W 2 1600 W 2000 W





Input Channels 4 (balanced line level) 4, selectable range





Audio Outputs


Connectors, Output 8-pin Phoenix Contact connector (part # 1778120), supports 10-24 AWG wire











Physical













Power Rating 1

2 Ω 4 Ω 8 Ω 70 V 100 V



V-Bridge Mode 250 W 2

500 W 500 W 400 W 500 W

I-Share Mode 500 W 250 W 2

150 W 2

Not available Not available

Quad Mode 1000 W 2

1000 W 500 W 2

800 W 1000 W


Peak Output Voltage 71 / 142 / 142 V



Input Channels 4 (balanced line level) 4, selectable range





Audio Outputs


Connectors, Output 8-pin Phoenix Contact connector (part # 1778120), supports 10-24 AWG wire











Physical












AC Current Draw and Thermal Dissipation Information

PM8500 / PM8500N, AC Current Draw and Thermal Dissipation

Test Signal & Power LevelLoad Configuration

(All Channels Driven)Total Audio Output, W

120VAC 60Hz. Typical Line Current, A


Thermal Dissipation, Typical

Watts BTU/hr. kCal/hr.

Idle (Standby, Networked) N/A 0 0.3 0.1 31 106 27

Idle (Awake) N/A 0 1.3 0.7 176 601 151

1/8th Rated Power IEC65 Bandlimited Pink Noise,

6dB Crest Factor

8Ω/Ch Mono 16Ω/Ch V-Bridge

8Ω/Ch Quad300 4.2 2.3 205 699 176

4Ω/Ch Mono 2Ω/Ch I-Share

8Ω/Ch V-Bridge 4Ω/Ch Quad

500 6.4 3.3 272 928 234

1/3rd Rated Power IEC65 Bandlimited Pink Noise,

6dB Crest Factor


8Ω/Ch Quad800 9.3 4.8 275 938 236



1,333 14.9 7.5 455 1,553 391









Idle (Awake) N/A 0 1.3 0.7 176 601 151


6dB Crest Factor


8Ω/Ch Quad250 3.9 2.1 201 686 173



250 3.9 2.0 214 730 184


6dB Crest Factor


8Ω/Ch Quad667 8.0 4.2 281 959 242



667 8.1 4.1 308 1,051 265




120VAC 60Hz. Typi-cal Line Current, A





Idle (Awake) N/A 0 1.0 0.5 114 398 98


6dB Crest Factor


8Ω/Ch Quad150 2.6 1.6 130 444 112



250 3.4 1.8 162 553 139


6dB Crest Factor


8Ω/Ch Quad400 5.2 3.0 172 587 148



667 7.6 3.9 241 822 207











Idle (Awake) N/A 0 0.9 0.5 110 375 95


6dB Crest Factor


8Ω/Ch Quad125 2.4 1.5 133 454 114



125 2.2 1.1 138 471 119


6dB Crest Factor


8Ω/Ch Quad333 4.6 2.7 178 607 153



333 4.2 2.2 173 590 149


pro.Bose.com Additional Resources

Additional Resources

Visit us on the web at pro.Bose.com for more information, including specifications, technical literature, product warranty, parts and accessories, and global support contact information.

Date of Manufacture: The eighth digit in the serial number indicates the year of manufacture; “7” is 2007 or 2017.

China Importer: Bose Electronics (Shanghai) Company Limited, Part C, Plan 9, No. 353 North Riying Road, China (Shanghai) Pilot Free Trade Zone

EU Importer: Bose Products B.V., Gorslaan 60, 1441 RG Purmerend, The Netherlands

Mexico Importer: Bose de México, S. de R.L. de C.V. , Paseo de las Palmas 405-204, Lomas de Chapultepec, 11000 México, D.F. For importer & service information: +5255 (5202) 3545

Taiwan Importer: Bose Taiwan Branch, 9F-A1, No. 10, Section 3, Minsheng East Road, Taipei City 104, Taiwan. Phone Number: +886-2-2514 7676

Bose Corporation Headquarters: 1-877-230-5639

©2018 Bose Corporation. No part of this work may be reproduced, modified, distributed or otherwise used without prior written permission.

©2019 Bose Corporation. All rights reserved.The Mountain, Framingham, MA 01701-9168 USA

www.pro.Bose.comAll trademarks are the property of their respective owners.

AM855982 Rev. 00

Date post:	25-Feb-2021
Category:	Documents
Upload:	others
View:	1 times
Download:	0 times

PowerMatch - Bosesistema, ya que pueden provocar averías o riesgo de incendio. ADVERTENCIA : Con el...

Documents