3/1/2018 Powertrain Control Module (PCM) - NGC (ALL Diagnostic Trouble Codes ( DTC )) - ALLDATA
https://my.alldata.com/repair/#/repair/article/49105/component/3926/itype/423/nonstandard/1469401 1/20
2011 Dodge or Ram Truck Grand Caravan V6-3.6LVehicle > ALL Diagnostic Trouble Codes ( DTC ) > Testing and Inspection > P Code Charts > P0128
POWERTRAIN CONTROL MODULE (PCM) - NGC
P0128-THERMOSTAT RATIONALITY
Special Tools:
3/1/2018 Powertrain Control Module (PCM) - NGC (ALL Diagnostic Trouble Codes ( DTC )) - ALLDATA
https://my.alldata.com/repair/#/repair/article/49105/component/3926/itype/423/nonstandard/1469401 2/20
For a complete wiring diagram, refer to the Wiring Information .
3/1/2018 Powertrain Control Module (PCM) - NGC (ALL Diagnostic Trouble Codes ( DTC )) - ALLDATA
https://my.alldata.com/repair/#/repair/article/49105/component/3926/itype/423/nonstandard/1469401 3/20
Theory of Operation
The Powertrain Control Module (PCM) predicts what the engine coolant temperature should be, based on the engine coolant temperature at start-up, ambienttemperature and how the vehicle is subsequently driven. The predicted engine coolant temperature is compared to the Engine Coolant Temperature Sensorreading. The error between the two is calculated and integrated with respect to time. When the Thermostat diagnostic runs, the integrated error is comparedto a calibrated threshold and pass/fail is determined. Separate pass and fail thresholds are used in order to improve accuracy of the diagnostic.
- When Monitored: With the engine running, ambient temperature between -8° C (17.6° F) and 50° C (122° F), start up coolant temperature less than 50° C (122° F) and averagevehicle speed greater than 16 kph (10 mph) until coolant temperature reaches 85° C (185° F).
- Set Condition: The PCM detects that the actual engine coolant temperature falls too far below the predicted engine coolant temperature and the predicted coolanttemperature reaches the predicted target value before the actual coolant temperature reaches the actual coolant temperature target value. Two trip fault.Three good trips to turn off the MIL.
Always perform the Pre-Diagnostic Troubleshooting procedure before proceeding. .
See: Computers and Control Systems > Initial Inspection and DiagnosticOverview > Pre-Diagnostic Troubleshooting Procedure
1. ACTIVE DTC
NOTE: If any ECT, AAT, CMP or CKP sensor DTCs have set along with P0128, diagnose them before continuing.
NOTE: Make sure that the Pinion Factor has been programmed correctly into the PCM.
1. Start the engine.
3/1/2018 Powertrain Control Module (PCM) - NGC (ALL Diagnostic Trouble Codes ( DTC )) - ALLDATA
https://my.alldata.com/repair/#/repair/article/49105/component/3926/itype/423/nonstandard/1469401 4/20
2. Allow the engine to reach normal operating temperature. 3. With the scan tool, select View DTCs.
NOTE: It may be necessary to drive the vehicle to meet the conditions to set this DTC, try to repeat the conditions in which the fault originally set by reviewingthe Freeze Frame data.
Is the DTC Active or Pending at this time?
Yes
- Go To 2
No
- Perform the INTERMITTENT CONDITION diagnostic procedure. See: Computers and Control Systems > Initial Inspection and Diagnostic Overview >Intermittent Condition Test.
2. LOW COOLANT LEVEL
NOTE: If an Engine Coolant Temperature (ECT) DTC is set along with this code, diagnose the ECT DTC first.
NOTE: Inspect the ECT terminals and related PCM terminals. Make sure the terminals are free from corrosion and damage.
NOTE: The best way to diagnose this DTC is to allow the vehicle to sit overnight outside in order to have a totally cold soaked engine.
NOTE: Extremely cold outside ambient temperatures may have caused this DTC to set.
WARNING: Never open the cooling system when the engine is hot. The system is under pressure. Failure to follow these instructions can result in personalinjury including extreme burns, scalding, or fatal injury. Allow the engine to cool before opening the cooling system.
1. Check the coolant system to make sure that the coolant is in good condition and at the proper level. See: Cooling System > Component Tests and GeneralDiagnostics.
Is the coolant level and condition OK?
Yes
3/1/2018 Powertrain Control Module (PCM) - NGC (ALL Diagnostic Trouble Codes ( DTC )) - ALLDATA
https://my.alldata.com/repair/#/repair/article/49105/component/3926/itype/423/nonstandard/1469401 5/20
- Go To 3
No
- Inspect the vehicle for a coolant leak and add the necessary amount of coolant. See: Cooling System > Mechanical > Cooling System TorqueSpecifications. - Perform the POWERTRAIN VERIFICATION TEST. See: A L L Diagnostic Trouble Codes ( DTC ) > Verification Tests > Powertrain Verification Test.
3. THERMOSTAT OPERATION
NOTE: This test works best if performed on a cold engine (cold soak).
1. Ignition on, engine not running. 2. With the scan tool, read the ECT Deg value. If the engine was allowed to sit overnight (cold soak), the temperature value should be a value that issomewhere close to the ambient temperature.
NOTE: If engine coolant temperature is above 82° C (180° F), allow the engine to cool until 65° C (150° F) is reached.
3. Start the Engine. 4. During engine warm-up, monitor the ECT Deg value. The temp deg value change should be a smooth transition from start up to normal operating temp 82°C (180° F). Also monitor the actual coolant temperature with a thermometer.
NOTE: As the engine warms up to operating temperature, the actual coolant temperature (thermometer reading) and the scan tool, ECT Temperature valueshould stay relatively close to each other.
5. Using the appropriate Service Information, determine the proper opening temperature of the thermostat.
Did the thermostat open at the proper temperature?
Yes
- Go To 4
No
- Replace the thermostat. See: Thermostat, Engine Cooling > Removal and Replacement > Engine Coolant Thermostat - Removal. - Perform the POWERTRAIN VERIFICATION TEST. See: A L L Diagnostic Trouble Codes ( DTC ) > Verification Tests > Powertrain Verification Test.
3/1/2018 Powertrain Control Module (PCM) - NGC (ALL Diagnostic Trouble Codes ( DTC )) - ALLDATA
https://my.alldata.com/repair/#/repair/article/49105/component/3926/itype/423/nonstandard/1469401 6/20
4. AMBIENT AIR TEMP SENSOR OPERATION 1. Ignition on, engine not running. 2. With the scan tool, read and record the AAT Sensor Temperature value. 3. Monitor the actual ambient air temperature near the AAT Sensor with a thermometer.
Is the AAT Sensor value with -15° C (5° F) of the thermometer reading?
Yes
- Go To 5
No
- Go To 7
5. ECT SENSOR OPERATION
WARNING: Make sure the engine cooling system is cool before removing the pressure cap or any hose. The cooling system is pressurized when hot. Failureto follow these instructions can result in possible serious or fatal injury.
1. With the scan tool, read and record the ECT Sensor Temperature value. 2. Monitor the actual coolant temperature with a thermometer.
Is the ECT Sensor value with -15° C (5° F) of the thermometer reading?
Yes
- Go To 6
No
- Go To 7
6. OTHER POSSIBLE CAUSES 1. Inspect the Temperature Sensors for any physical damage. 2. Inspect the engine coolant. Make sure the coolant is at the proper level. See: Cooling System > Mechanical > Cooling System Torque Specifications
3/1/2018 Powertrain Control Module (PCM) - NGC (ALL Diagnostic Trouble Codes ( DTC )) - ALLDATA
https://my.alldata.com/repair/#/repair/article/49105/component/3926/itype/423/nonstandard/1469401 7/20
3. Make sure the Temperature Sensors are properly installed. 4. Make sure the CMP and CKP sensors are installed properly. Check the connectors for any signs of damage.
WARNING: When the engine is operating, do not stand in direct line with the fan. Do not put your hands near the pulleys, belts or fan. Do not wear looseclothing. Failure to follow these instructions may result in possible serious or fatal injury.
5. Perform any Technical Service Bulletins (TSBs) that may apply. 6. With the engine running at normal operating temperature, monitor the Temperature sensor parameters while wiggling the wire harness. Look for parametervalues to change. 7. Visually inspect the related wire harness. Look for any chafed, pierced, pinched, partially broken wires and broken, bent, pushed out or corroded terminals.
CAUTION: Do not probe the PCM harness connectors. Probing the PCM harness connectors will damage the PCM terminals resulting in poor terminal to pinconnection. Install the PCM Pinout Box to perform diagnosis.
8. Inspect and clean all PCM, engine and chassis grounds.
Were any problems found during the above inspections?
Yes
- Repair as necessary. - Perform the POWERTRAIN VERIFICATION TEST. See: A L L Diagnostic Trouble Codes ( DTC ) > Verification Tests > Powertrain Verification Test.
No
- Test Complete, the conditions that set this DTC are not present at this time.
7. SIGNAL CIRCUIT SHORTED TO VOLTAGE
3/1/2018 Powertrain Control Module (PCM) - NGC (ALL Diagnostic Trouble Codes ( DTC )) - ALLDATA
https://my.alldata.com/repair/#/repair/article/49105/component/3926/itype/423/nonstandard/1469401 8/20
3/1/2018 Powertrain Control Module (PCM) - NGC (ALL Diagnostic Trouble Codes ( DTC )) - ALLDATA
https://my.alldata.com/repair/#/repair/article/49105/component/3926/itype/423/nonstandard/1469401 9/20
NOTE: Visually inspect both the component and the PCM connectors. Look for damage, partially broken wires and backed out or corroded terminals
1. Turn the ignition off. 2. Disconnect the applicable Temperature Sensor harness connector. 3. Disconnect the TIPM C4 harness connector and the C2 PCM harness connector. 4. Ignition on, engine not running. 5. Measure the voltage on the (K2) ECT Signal circuit and the (G31) AAT Signal circuit at the appropriate Temperature Sensor harness connector.
Is there any voltage present?
Yes
3/1/2018 Powertrain Control Module (PCM) - NGC (ALL Diagnostic Trouble Codes ( DTC )) - ALLDATA
https://my.alldata.com/repair/#/repair/article/49105/component/3926/itype/423/nonstandard/1469401 10/20
- Repair the short to voltage in the Signal circuit. - Perform the POWERTRAIN VERIFICATION TEST. See: A L L Diagnostic Trouble Codes ( DTC ) > Verification Tests > Powertrain Verification Test.
No
- Go To 8
8. TEMPERATURE SENSOR
image
3/1/2018 Powertrain Control Module (PCM) - NGC (ALL Diagnostic Trouble Codes ( DTC )) - ALLDATA
https://my.alldata.com/repair/#/repair/article/49105/component/3926/itype/423/nonstandard/1469401 11/20
1. Turn the ignition off. 2. Connect the TIPM C4 harness connector and the C2 PCM harness connector. 3. Ignition on, engine not running. 4. With the scan tool, read the Temperature Sensor voltage. 5. Connect a jumper wire across the ECT and AAT Sensor harness connectors.
Does the voltage start at 5.0 Volts and drop below 1.0 Volt when the jumper wire is installed?
Yes
- Verify that there is good pin to terminal contact in the Sensor and Control Module connectors. If OK, replace the appropriate Temperature Sensor. See:Coolant Temperature Sensor/Switch (For Computer) > Removal and Replacement > Engine Coolant Temperature Sensor - Removal or See: Air TemperatureSensor ( Ambient / Intake ) > Removal and Replacement > Removal.
3/1/2018 Powertrain Control Module (PCM) - NGC (ALL Diagnostic Trouble Codes ( DTC )) - ALLDATA
https://my.alldata.com/repair/#/repair/article/49105/component/3926/itype/423/nonstandard/1469401 12/20
- Perform the POWERTRAIN VERIFICATION TEST. See: A L L Diagnostic Trouble Codes ( DTC ) > Verification Tests > Powertrain Verification Test.
No
- Go To 9NOTE: Disconnect the jumper wire before continuing.
9. SIGNAL CIRCUIT OPEN
3/1/2018 Powertrain Control Module (PCM) - NGC (ALL Diagnostic Trouble Codes ( DTC )) - ALLDATA
https://my.alldata.com/repair/#/repair/article/49105/component/3926/itype/423/nonstandard/1469401 13/20
1. Turn the ignition off.
CAUTION: Do not probe the PCM harness connectors. Probing the PCM harness connectors will damage the PCM terminals resulting in poor terminal to pinconnection. Install the PCM Pinout Box to perform diagnosis.
2. Measure the resistance of the (K2) ECT Sensor Signal circuit from the ECT Sensor harness connector to the appropriate terminal of the PCM Pinout Box. 3. Measure the resistance of the (G31) AAT Sensor Signal circuit from the AAT Sensor harness connector to the TIPM C4 harness connector.
Is the resistance below 5.0 Ohms?
3/1/2018 Powertrain Control Module (PCM) - NGC (ALL Diagnostic Trouble Codes ( DTC )) - ALLDATA
https://my.alldata.com/repair/#/repair/article/49105/component/3926/itype/423/nonstandard/1469401 14/20
Yes
- Go To 10
No
- Repair the open in the Sensor Signal circuit. - Perform the POWERTRAIN VERIFICATION TEST. See: A L L Diagnostic Trouble Codes ( DTC ) > Verification Tests > Powertrain Verification Test.
10. SENSOR GROUND CIRCUIT OPEN
3/1/2018 Powertrain Control Module (PCM) - NGC (ALL Diagnostic Trouble Codes ( DTC )) - ALLDATA
https://my.alldata.com/repair/#/repair/article/49105/component/3926/itype/423/nonstandard/1469401 15/20
1. Measure the resistance of the (K900) Sensor ground circuit from the appropriate Temperature Sensor harness connector to the appropriate terminal of thePCM Pinout Box. 2. Measure the resistance of the (G931) Sensor ground circuit from the AAT Sensor harness connector to the TIPM C4 harness connector.
Is the resistance below 5.0 Ohms?
Yes
- Go To 11
3/1/2018 Powertrain Control Module (PCM) - NGC (ALL Diagnostic Trouble Codes ( DTC )) - ALLDATA
https://my.alldata.com/repair/#/repair/article/49105/component/3926/itype/423/nonstandard/1469401 16/20
No
- Repair the open in the Sensor ground circuit. - Perform the POWERTRAIN VERIFICATION TEST. See: A L L Diagnostic Trouble Codes ( DTC ) > Verification Tests > Powertrain Verification Test.
11. SIGNAL CIRCUIT SHORTED TO GROUND
3/1/2018 Powertrain Control Module (PCM) - NGC (ALL Diagnostic Trouble Codes ( DTC )) - ALLDATA
https://my.alldata.com/repair/#/repair/article/49105/component/3926/itype/423/nonstandard/1469401 17/20
1. Measure the resistance between ground and the Sensor Signal circuit in the Temperature Sensor harness connector.
Is the resistance below 100 Ohms?
Yes
- Repair the short to ground in the Signal circuit. - Perform the POWERTRAIN VERIFICATION TEST. See: A L L Diagnostic Trouble Codes ( DTC ) > Verification Tests > Powertrain Verification Test.
No
- Go To 12
3/1/2018 Powertrain Control Module (PCM) - NGC (ALL Diagnostic Trouble Codes ( DTC )) - ALLDATA
https://my.alldata.com/repair/#/repair/article/49105/component/3926/itype/423/nonstandard/1469401 18/20
12. SIGNAL CIRCUIT SHORTED TO THE (K900) SENSOR GROUND CIRCUIT OR THE (G931) SENSOR GROUND CIRCUIT
3/1/2018 Powertrain Control Module (PCM) - NGC (ALL Diagnostic Trouble Codes ( DTC )) - ALLDATA
https://my.alldata.com/repair/#/repair/article/49105/component/3926/itype/423/nonstandard/1469401 19/20
1. Measure the resistance between the Signal circuit and the (K900) Sensor ground circuit in the (K2) ECT Sensor harness connector. 2. Measure the resistance between the Signal circuit and the (G931) Sensor ground circuit in the (G31) AAT Sensor harness connector.
Is the resistance below 100 Ohms?
Yes
- Repair the short between the Sensor ground circuit and the Sensor Signal circuit. - Perform the POWERTRAIN VERIFICATION TEST. See: A L L Diagnostic Trouble Codes ( DTC ) > Verification Tests > Powertrain Verification Test.
No
- Go To 13
3/1/2018 Powertrain Control Module (PCM) - NGC (ALL Diagnostic Trouble Codes ( DTC )) - ALLDATA
https://my.alldata.com/repair/#/repair/article/49105/component/3926/itype/423/nonstandard/1469401 20/20
13. POWERTRAIN CONTROL MODULE (PCM) 1. Using the wiring diagram/schematic as a guide, inspect the wiring and connectors between the Temperature Sensors and the Powertrain Control Module(PCM). 2. Look for any chafed, pierced, pinched or partially broken wires. 3. Look for broken, bent, pushed out or corroded terminals. Verify that there is good pin to terminal contact in the Sensor and Powertrain Control Moduleconnectors. 4. Perform any Technical Service Bulletins that may apply.
Were there any problems found?
Yes
- Repair as necessary. - Perform the POWERTRAIN VERIFICATION TEST. See: A L L Diagnostic Trouble Codes ( DTC ) > Verification Tests > Powertrain Verification Test.
No
- Replace and program the Powertrain Control Module. See: Engine Control Module > Removal and Replacement > Powertrain Control Module - Removal. - Perform the POWERTRAIN VERIFICATION TEST. See: A L L Diagnostic Trouble Codes ( DTC ) > Verification Tests > Powertrain Verification Test.