F:\AESBusinessSystems\AES Technical\Piece part instructions\PP-1030-LR Wire Harness Assembly LR01.doc
Wire Harness Assembly Part #PP-1030-LR For Models LR-01 (prior to 2011)
• Unplug unit. • Open both side panels. • Remove existing wire harness. • Attach the following:
o Control Board molex connector o Exhaust Fan gray/white & black molex to black leads o Auger Motor brown/white & black to black leads o Room Air Fan blue/white & black molex to black leads o Vacuum Pressure Switch green lead to top terminal violet lead to bottom terminal o High Limit Snap Disk gray lead to top terminal violet to bottom terminal
all white snap disk o Snap disc right side yellow wire to top terminal violet wire to bottom terminal
yellow & white snap disk o Proof of Fire Snap Disk brown wire to top terminal violet wire to bottom terminal
o located by exhaust motor yellow & white snap disk o Electrical Plug double white wires middle terminal black wire bottom terminal
green wire to top terminal other end of green wire screwed to base of unit
o Igniter red wire to one lead white wire to one lead o thermostat blue lead and red lead (these are not used if NO thermostat)
• Plug unit in • Turn on unit
F:\AESBusinessSystems\AES Technical\Piece part instructions\PP-1030-LR Wire Harness Assembly LR01.doc
high limit snap disc
control board
room air fanpower inlet
auger motor
vacuum switch
F:\AESBusinessSystems\AES Technical\Piece part instructions\PP-1030-LR Wire Harness Assembly LR01.doc
/ColorImageDict > /JPEG2000ColorACSImageDict > /JPEG2000ColorImageDict > /AntiAliasGrayImages false /CropGrayImages true /GrayImageMinResolution 300 /GrayImageMinResolutionPolicy /OK /DownsampleGrayImages true /GrayImageDownsampleType /Bicubic /GrayImageResolution 300 /GrayImageDepth -1 /GrayImageMinDownsampleDepth 2 /GrayImageDownsampleThreshold 1.50000 /EncodeGrayImages true /GrayImageFilter /DCTEncode /AutoFilterGrayImages true /GrayImageAutoFilterStrategy /JPEG /GrayACSImageDict > /GrayImageDict > /JPEG2000GrayACSImageDict > /JPEG2000GrayImageDict > /AntiAliasMonoImages false /CropMonoImages true /MonoImageMinResolution 1200 /MonoImageMinResolutionPolicy /OK /DownsampleMonoImages true /MonoImageDownsampleType /Bicubic /MonoImageResolution 1200 /MonoImageDepth -1 /MonoImageDownsampleThreshold 1.50000 /EncodeMonoImages true /MonoImageFilter /CCITTFaxEncode /MonoImageDict > /AllowPSXObjects false /CheckCompliance [ /None ] /PDFX1aCheck false /PDFX3Check false /PDFXCompliantPDFOnly false /PDFXNoTrimBoxError true /PDFXTrimBoxToMediaBoxOffset [ 0.00000 0.00000 0.00000 0.00000 ] /PDFXSetBleedBoxToMediaBox true /PDFXBleedBoxToTrimBoxOffset [ 0.00000 0.00000 0.00000 0.00000 ] /PDFXOutputIntentProfile () /PDFXOutputConditionIdentifier () /PDFXOutputCondition () /PDFXRegistryName () /PDFXTrapped /False
/Description > /Namespace [ (Adobe) (Common) (1.0) ] /OtherNamespaces [ > /FormElements false /GenerateStructure false /IncludeBookmarks false /IncludeHyperlinks false /IncludeInteractive false /IncludeLayers false /IncludeProfiles false /MultimediaHandling /UseObjectSettings /Namespace [ (Adobe) (CreativeSuite) (2.0) ] /PDFXOutputIntentProfileSelector /DocumentCMYK /PreserveEditing true /UntaggedCMYKHandling /LeaveUntagged /UntaggedRGBHandling /UseDocumentProfile /UseDocumentBleed false >> ]>> setdistillerparams> setpagedevice