PrefaceHP MIO
Preface
Thank you for purchasing the AXIS HP MIO printer interface. Our goal in developing this product is to provide you with a high-quality, high-performance interface between the IBM system environment and your Hewlett-Packard printer, combining the best of both worlds.
About Axis
Axis Communications is dedicated to provide inventive solutions for network connection of computer peripherals. Since the start in 1984, it has been one of the fastest growing companies in the market. The headquarters are located in Lund, Sweden, with subsidiaries in Boston, Tokyo, and Hong Kong.
Axis Communications has a distributor network operating in more than 50 countries world-wide, marketing three product lines:
IBM Mainframe and S/3x – AS/400 Printer Interfaces: These products include a wide range of plug-in interfaces and stand-alone products such as the AXIS Cobra+, AXIS 330/370 Cobra, AXIS HP MIO, the AXIS AFP IPDS-to-PostScript converter, and the AXIS AFP MIO/IOP IPDS-to-PCL converters
Network Print Servers: These intelligent Ethernet and Token Ring print servers support a wide range of LAN protocols. The AXIS 540, AXIS 560 and AXIS 570 are Ethernet print servers, and the AXIS 640, AXIS 660 and AXIS 670 are Token Ring print servers. The AXIS 150 is an Ethernet print server dedicated to PC networks.
CD-ROM Servers: Axis CD-ROM servers allow CD-ROM data to be shared over the network. The product range includes the AXIS 850 and AXIS 851 Ethernet CD-ROM servers as well as the AXIS 950 and AXIS 951 Token Ring CD-ROM servers.
AXIS HP MIO User’s Manual 1
PrefaceHP MIO
ABOUT THIS MANUAL
This manual will guide you through a simple step-by-step installation and configuration procedure. It is divided into four sections:
1. INTRODUCTION – The AXIS HP MIO board, how it works, where to use it, and its main features.
2. GETTING STARTED – How to install the AXIS HP MIO board into your printer, and how to connect it to the IBM system.
3. CONFIGURATION – How to configure the AXIS HP MIO using the printer’s front panel.
4. ADVANCED FUNCTIONS – An overview of AXIS HP MIO functions beyond the standard IBM printer emulation.
The manual applies to the AXIS HP MIO with firmware release 1.21 and subsequent releases until otherwise notified. Please refer to the AXIS HP MIO Technical Reference for further information of functions and parameters.
Every care has been taken in the preparation of this manual; if you detect any inaccuracies or omissions, please inform us at the address on the back cover. Axis Communications AB cannot be held responsible for any technical or typographical errors and reserves the right to make changes to the product and manuals without prior notice.
2 AXIS HP MIO User’s Manual
PrefaceHP MIO
Emission Notices
USA This equipment generates, uses, and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual, may cause interference to radio communications. It has been tested and found to comply with the limits for a Class A computing device pursuant to Subpart B of Part 15 of FCC rules, which are designed to provide reasonable protection against such interference when operated in a commercial environment. Operation of this equipment in a residential area is likely to cause interference in which case the user, at his own expense, will be required to take whatever measures may be required to correct the interference. Shielded cables should be used with this unit to ensure compliance with the Class A limits.
Europe This digital equipment fulfils the requirements for radiated emission according to limit B of EN55022/1987, and the requirements for immunity according to EN50082-1/1992 residential, commercial, and light industry. (Compliance is not valid for unshielded network and printer cables.)
Trademark Acknowledgements
IBM and Hewlett Packard are registered trademarks of the respective holders.
AXIS HP MIO User’s Manual Revision: 1.2
Part No: 13142 Dated: June, 1996
Copyright © Axis Communications AB, 1996
AXIS HP MIO User’s Manual 3
PrefaceHP MIO
This page is intentionally blank
4 AXIS HP MIO User’s Manual
Table of Contents
Table of Contents
Section 1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7How It Works . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8Where To Use It . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9Main Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Section 2 Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11Hardware Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12Verifying the Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14Connecting to the System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Section 3 Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17The Front Panel Menus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18System Language (SYSL) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19IBM Printer Emulation (PREMUL) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20Maximum Page Length (MPL) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21Automatic Orientation (AUTORI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22Page Orientation (PAGEORI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23Page Size (PAGESIZE) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24Custom Page Width (PAGEWIDTH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25Custom Page Length (PAGELENGTH) . . . . . . . . . . . . . . . . . . . . . . . . . . . 26Print Parameter List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Section 4 Advanced Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29Configuration from the System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30Hex Transparency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31Font Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Appendix A The AXIS HP MIO Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34The System Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34The PC SHARE Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35The Rotary Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35The Coax/Twinax Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35Test Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
AXIS HP MIO User’s Manual 5
Table of Contents
Appendix B System Configuration Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 375250/Twinax Host Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 373270 Host Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Appendix C Fonts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Appendix D Technical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Appendix E How To Contact Axis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46Axis on-line service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Appendix F Related Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
6 AXIS HP MIO User’s Manual
Section 1: IntroductionHP MIO
Section 1 Introduction
The AXIS HP MIO is a plug-in interface board that makes it possible to connect a Hewlett-Packard printer to an IBM AS/400, S/3x, or Mainframe environment. It supports all HP printers with an MIO expansion slot, such as LaserJet 5Si, LaserJet 4Si, LaserJet 4+, Color LaserJet, DesignJet, and PaintJet XL300.
Your HP printer with the AXIS HP MIO appears to the IBM system as an original IBM printer, while still maintaining its PC or LAN printer capabilities.
In addition, the AXIS HP MIO allows you to make full use of all HP printer features in the IBM system environment.
The AXIS HP MIO board
AXIS HP MIO User’s Manual 7
Section 1: IntroductionHP MIO
How It Works
An IBM system communicates with printers using a high-speed, bi-directional protocol very different from the PC standard parallel and serial connections.
In the AXIS HP MIO, the conversion of IBM system data to HP printer data is carried out in three steps as illustrated in the picture below:
The AXIS HP MIO IBM System to HP Printer Data Conversion
The IBM System Communication block extracts the print data, page formatting commands, and font selection commands from the IBM data stream.
The Conversion to PCL block converts the data into PCL, which is the format used by HP printers.
The Printer Driver block passes the data on to the printer using the internal MIO (Modular Input/Output) interface.
The Printer Driver also accepts PCL data from a local PC or a LAN print server (such as the AXIS NPS 560) using the AXIS HP MIO parallel port. In this way, you can share the printer between two different environments. The PC/LAN print data is not converted or otherwise modified by the AXIS HP MIO board.
8 AXIS HP MIO User’s Manual
Section 1: IntroductionHP MIO
Where To Use It
The pictures below show the HP printer with AXIS HP MIO interface in an IBM environment, also illustrating the printer sharing function. The top picture is a 3270/Coax installation, and the bottom picture is a 5250/Twinax installation.
The HP printer with AXIS HP MIO in an IBM 3270/Coax environment
The HP printer with AXIS HP MIO in an IBM 5250/Twinax environment
AXIS 560/660 Ethernet Print Server
PC
AXIS 560/660 Ethernet Print Server
PC
AXIS HP MIO User’s Manual 9
Section 1: IntroductionHP MIO
Main Features
Reliability The AXIS HP MIO hardware is a state-of-the-art RISC architecture design. Based on highly integrated circuits, it combines low power consumption with high performance and reliability.
Compatibility The AXIS HP MIO interface is designed to be fully compatible with the emulated IBM printers. You can print all your existing documents without having to adapt them specially for the AXIS HP MIO.
Ease of Use The AXIS HP MIO is delivered in ready-to-run state. The few parameters you might need to change are directly accessed from the printer’s front panel.
Flexibility For the advanced user, the AXIS HP MIO has a large number of configuration parameters that allows you to tailor the interface to meet a wide range of specific needs.
IBM Printer Emulations The AXIS HP MIO is pre-configured to emulate an IBM 3816 page printer. This selection makes the best use of the HP printer capabilities, but you can also select from a wide range of other IBM printers.
Fonts The pre-defined font definition table contains 130 IBM fonts, each mapped to a printer resident PCL font. The font mapping is designed to emulate, as close as possible, the output from an original IBM printer and at the same time offer full access to the HP printer’s scalable fonts.
Printer Sharing You can share the printer between the Coax/Twinax host and up to three different local PCs or LAN print servers connected to the AXIS HP MIO parallel port and the printer’s own parallel and serial ports. You do not have to purchase any special cabling, since standard printer cables may be used. The printer sharing requires no operator intervention, and no AXIS HP MIO or printer configuration.
10 AXIS HP MIO User’s Manual
Section 2: Getting StartedHP MIO
Section 2 Getting Started
Unpack and inspect all parts for damage. Contact your dealer if anything is missing or damaged. All packing materials are recyclable, including the anti-static bag.
Caution The AXIS HP MIO board contains static-sensitive components. Always hold the board by the edges or the rear panel when removed from the anti-static bag. Make sure to take all recommended precautions related to static-sensitive devices.
The standard delivery contains the following:
❏ AXIS HP MIO board, part no. 0045-1 (European version) or
AXIS HP MIO board, part no. 0045-3 (US version)
❏ AXIS HP MIO User’s Manual (part no. 13142)
Optional accessories:
❏ AXIS Twinax T-cable (part no. 12554)
❏ Centronics parallel printer cable (part no. 13133)
AXIS HP MIO User’s Manual 11
Section 2: Getting StartedHP MIO
Hardware Installation
Before you begin the installation, you must set the rear panel Coax/Twinax switch in the correct position. Use a flat screwdriver to set the switch in CX position (shown to the left) for 3270/Coax mode, or TX position for 5250/Twinax mode.
The AXIS HP MIO board should be installed into the MIO expansion slot at the rear of your HP printer. The guidelines below are for the HP LaserJet 4p, but the installation procedure is similar for all HP printers. If you have a printer other than the LaserJet 4+, consult the printer manual on how to access the MIO slot.
You will need one Philips and one flat screwdriver for the installation.
Removing the cover plate (HP LaserJet 4+)
12 AXIS HP MIO User’s Manual
Section 2: Getting StartedHP MIO
Follow these steps and refer to the illustrations to install the AXIS HP MIO board:
1. Switch off the printer.
2. Remove the cover plate over the MIO slot.
3. Slide the AXIS HP MIO board into place.
4. Tighten the two screws securing the rear panel.
5. Set the rotary switch in position ‘0’.
6. Switch on the printer.
The hardware installation is now completed.
Caution Twinax users: Do not connect the printer to the IBM system before the rotary switch is set to the correct device address (see Section 2.3).
The AXIS HP MIO board installed (HP LaserJet 4+)
AXIS HP MIO User’s Manual 13
Section 2: Getting StartedHP MIO
Verifying the Installation
After completing the hardware installation, you can verify that the AXIS HP MIO board is running by printing the Self Test page (see sample on the next page). On the HP LaserJet 4, this entry is found under the TEST MENU.
The AXIS HP MIO identification is printed under the MIO MENU title. The example below is for an AXIS HP MIO board in 5250/Twinax mode, the 3270/Coax mode is marked ‘inactive’.
The AXIS HP MIO parameters are printed under the MIO MENU title. This shows the current settings for the configuration parameters available from the front panel.
14 AXIS HP MIO User’s Manual
Section 2: Getting StartedHP MIO
Extract from the HP LaserJet 4+ Self Test page
AXIS HP MIO User’s Manual 15
Section 2: Getting StartedHP MIO
Connecting to the System
The last step in the installation procedure is to connect your printer to the IBM Coax or Twinax host.
Caution Once again, make sure that the rear panel Coax/Twinax switch is in the correct position. The current mode is shown under the AUX IO INTERFACE title on the Self Test page.
The SYSTEM indicator will flash for a few seconds, and should then remain lit showing that contact with the IBM system is established.
You can verify the connection by making a local copy printout from your system.
The installation procedure is now completed. Your printer is ready for permanent use, and will not require any user intervention during normal operation.
For 5250/Twinax mode:
1. Switch off the printer.
2. Find a free device address on the Twinax port. The selected address must be configured for an IBM 3816 printer.
3. Set the rotary switch to the selected device address.
4. Connect the Axis T-cable bar to the twinax cables. Don't forget to notify your system operator before breaking the twinax line!
5. Connect the T-cable to the AXIS HP MIO board.
6. Switch on the printer.
For 3270/Coax mode:
1. Switch off the printer.
2. Find a free printer port on the control unit. The selected port must be configured for an LU-1 or LU-3 printer.
3. Connect a coax cable between the control unit and the AXIS HP MIO board.
4. Switch on the printer.
16 AXIS HP MIO User’s Manual
Section 3: Configuration
System language Page lenght Emulation
Section 3 Configuration
Your AXIS HP MIO board is configured at delivery to emulate an IBM 3816 page printer using Letter size or A4 paper. Should you want to change any of this, the following configuration parameters can be accessed from the printer’s front panel:
• System Language = 37 (US English)
• IBM Printer Emulation = 3816
• Maximum Page Length = 66 lines
• Automatic Orientation = YES
• Page Orientation = COR
• Page Size = LETTER (US version) or A4 (European version)
If you have a printer without a front panel, or if you want to change any of the parameters not available in the front panel menu, please refer to Section 4, Configuration from the System, and to AXIS HP MIO Technical Reference.
AXIS HP MIO User’s Manual 17
Section 3: Configuration
System language Page lenght Emulation
The Front Panel Menus
The remainder of this section describes how to change the AXIS HP MIO configuration parameters using the HP LaserJet 4+ front panel. The procedure for other HP printers is similar, but the menus are differently organized, and you may need to use different keys to navigate. However, guided by the printed Self Test page and the printer manual, you shouldn’t have any difficulties finding the menu entries.
The AXIS HP MIO configuration parameters are found under the MIO MENU. To get there, first set the printer off-line, then press the Menu key repeatedly until the MIO MENU appears.
Next, press the Item key to get into the menu. The first entry that appears is the System Language. An asterisk is displayed in the right-most position when the currently active value is shown.
Change the value as desired by pressing the ‘+’ or ‘-’ keys. Press Enter to save the new value, and the asterisk will be displayed.
Press Item again to scroll through the parameters.
When done, press the On-Line key, and the configuration is completed and saved.
18 AXIS HP MIO User’s Manual
Section 3: Configuration
System language Page lenght Emulation
The System Language parameter must match your IBM system configuration in order to get correct language specific characters.
The default System Language is 37 (US English). You only have to change this selection if your IBM system is configured for a different System Language. If in doubt, consult your System Manager.
Select System Language according to your IBM system configuration.
System LanguageSelections:
Note: ❏ Selections marked Cx will appear only in Coax mode, and Tx selections will appear only in Twinax mode.
System Language (SYSL) SYSL=37 *
VALUE DESCRIPTION VALUE DESCRIPTION
*37 US English, Portuguese Alternate, and Canadian Bilingual
286 Austrian/German Alternate Cx
256 New Spanish Word Processing Tx 287 Danish/Norwegian Alternate Cx
260 Canadian French Cx 288 Swedish/Finnish Alternate Cx
273 Austrian/German 289 Spanish Cx
274 Belgian 293 APL Cx
275 Brazilian 297 French/French Azerty
277 Danish/Norwegian 340 OCR Tx
278 Swedish/Finnish 361 International TypographicCx
280 Italian 500 International Set 5 and Swiss Bilingual
281 Japanese English 871 Icelandic
282 Portuguese 892 OCR-A Cx
284 Spanish and Spanish Speaking 893 OCR-B Cx
285 UK English
AXIS HP MIO User’s Manual 19
Section 3: Configuration
System language Page lenght Emulation
The IBM Printer Emulation parameter must match your IBM system configuration in order to get correctly formatted printouts.
The default IBM Printer Emulation is 3816 (IBM 3816 model 01S/01D). You will only have to change this selection if your IBM system is configured for a different IBM printer. If in doubt, consult your System Manager.
Select IBM Printer Emulation according to your IBM system configuration.
IBM Printer EmulationSelections:
Note: ❏ Selections marked Cx only will appear only in Coax mode, and Tx only selections will appear only in Twinax mode.
IBM Printer Emulation (PREMUL) SPREMUL=3816 *
VALUE DESCRIPTION
3812 IBM 3812 models 2 (Coax non-IPDS), and 1 and 2 (Twinax), page printer
* 3816 IBM 3816 models 01S and 01D, page printer
3287 IBM 3287 model 2C, matrix printer Cx only
3268 IBM 3268 model 2C, matrix printer Cx only
3262 IBM 3262 models 3 and 13, matrix printer Cx only
4214 IBM 4214 models 1 (Coax) and 2 (Twinax), matrix printer
4224 IBM 4224 model 2 non-IPDS, matrix printer Cx only
5224 IBM 5224 models 1 and 2, matrix printer Tx only
5225 IBM 5225 models 1 through 4, matrix printer Tx only
5226 IBM 5224 models 1 through 3, matrix printer Tx only
4230 IBM 4230 models 201 (Coax) and 101 (Twinax), matrix printer
20 AXIS HP MIO User’s Manual
Section 3: Configuration
System language Page lenght Emulation
The MPL parameter sets the number of lines per page. The AXIS HP MIO automatically ejects the page when the specified number of lines have been printed.
The default value is 66 lines. You should only change this selection if your documents are set up for a different page length.
Select Maximum Page Length.
Maximum PageLength Selections:
You can select any page length from 0 to 255 lines.
Note: Selecting 0 will give a page length of one line.
Maximum Page Length (MPL) SMPL=66 *
AXIS HP MIO User’s Manual 21
Section 3: Configuration
System language Page lenght Emulation
This parameter selects automatic or fixed page orientation.
The default selection is YES (Automatic Orientation). You can change this to NO if you want to print all pages in the same orientation regardless of the calculated (logical) page size, see below.
Select/deselect Automatic Orientation.
AutomaticOrientationSelections:
YES: Automatic Orientation. The page orientation depends on the page format set by the IBM host. For each new page, a logical page size is calculated and compared to the physical size set by the Page Size parameter, see page 24. The page orientation is then determined as follows:
• If the logical length is greater than the logical width, the page will be printed in Portrait orientation.
• If the logical length is less than or equal to the logical width, the page will be printed in Landscape orientation.
• If the logical page size doesn’t fit the page in either orientation, the page will be printed according to the Page Orientation parameter, see page 23.
NO: Fixed Orientation. The page will always be printed according to the Page Orientation parameter, see page 23.
Automatic Orientation (AUTORI) SAUTORI=YES *
22 AXIS HP MIO User’s Manual
Section 3: Configuration
System language Page lenght Emulation
This parameter sets the default page orientation. The default orientation is used when the current page doesn’t fit the physical page size set by the Page Size parameter, or when the Automatic Orientation parameter is set to NO.
The default selection is COR (Computer Output Reduction, see note). You should only change this if you want to disable the COR function.
Select default Page Orientation.
Page OrientationSelections
Notes: ❏ COR printouts have the following characteristics:
•Landscape orientation.
•Vertically compressed to 70%.
•Horizontally compressed by using a font of higher character density.
•Top and left margins of 0.5 inches each.
❏ This parameter applies to all available input bins. If you should need to configure input bins individually, refer to Configuration from the System on page 30.
Page Orientation (PAGEORI) SPAGEORI=COR *
VALUE DESCRIPTION
* COR Computer Output Reduction (COR) is enabled
PORT Use portrait as default orientation
LAND Use Landscape as default orientation
AXIS HP MIO User’s Manual 23
Section 3: Configuration
System language Page lenght Emulation
(US version)
(European version)
This parameter is used to set the physical page size. It must match the actual paper size you are using in order to get correct printouts.
The default size is LETTER for the US version, and A4 for the European version. You will only have to change this selection if you are using paper of a different format.
Select physical Page Size.
Page Size Selections:
Notes: ❏ If CUSTOM is selected, you will be prompted for the width and length parameters.
This parameter applies to all available input bins. If you should need to configure input bins individually, refer to Configuration from the System on page 30.
Page Size (PAGESIZE) SPAGESIZE=LETTER *
SPAGESIZE=A4 *
VALUE DESCRIPTION
EXEC 7.25 x 10.5 inches
* LETTER 8.5 x 11 inches US version default
LEGAL 8.5 x 14 inches
* A4 210 x 297 mm (8.27 x 11.69 inches) European version default
A3 297 x 420 mm (11.69 x 16.54 inches)
B4 250 x 353 mm (10.12 x 14.33 inches)
MON 3.8 x 7.5 inches (Monarch envelopes)
C10 4.1 x 9.4 inches (COM-10 envelopes)
DL 4.3 x 8.6 inches (DL envelopes)
CUSTOM User defined size
24 AXIS HP MIO User’s Manual
Section 3: Configuration
System language Page lenght Emulation
Note: This selection will only appear if you have selected CUSTOM as Page Size.
The selected page width must match the width of the actual paper you are using in order to get correct printouts. The page width is displayed in units of 0.01 inches.
The default value is the page width for the last selected page size (if you changed from LETTER to CUSTOM, the default width is 850, corresponding to 8.50 inches).
Select Custom Page Width.
Page Width Selections You can select any page width from 0 to 1999, corresponding to 0.00 – 19.99 inches.
Note: Pressing the + or - key changes the value in steps of 0.01 inches. By holding down the key for a few seconds, the value changes more rapidly, first in steps of 0.10 inches, then in steps of 1.00 inches.
Custom Page Width (PAGEWIDTH) SPAGEWIDTH=850 *
AXIS HP MIO User’s Manual 25
Section 3: Configuration
System language Page lenght Emulation
Note: This selection will only appear if you have selected CUSTOM as Page Size.
The selected page length must match the length of the actual paper you are using in order to get correct printouts. The page length is displayed in units of 0.01 inches.
The default value is the page length for the last selected page size (if you changed from LETTER to CUSTOM, the default length is 1100, corresponding to 11.00 inches).
Select Custom Page Length
Page LengthSelections
You can select any page length from 0 to 1999, corresponding to 0.00 – 19.99 inches.
Note: Pressing the + or - key changes the value in steps of 0.01 inches. By holding down the key for a few seconds, the value changes more rapidly, first in steps of 0.10 inches, then in steps of 1.00 inches.
Custom Page Length (PAGELENGTH) SPAGELENGTH=1100 *
26 AXIS HP MIO User’s Manual
Section 3: Configuration
System language Page lenght Emulation
This selection activates the Print Parameter List function. The Parameter List contains all AXIS HP MIO configuration parameters, and the complete font definition table.
The default selection is N (No). Change this to Y (Yes) and press Enter if you want to print the Parameter List. The printout starts when you press the On-Line key.
Select/deselect Parameter List printout.
Print Parameter ListOptions
N: No. The Parameter List will not be printed.
Y: Yes. The Parameter List will be printed when you set the printer on line.
Notes: ❏ As soon as the Parameter List has been printed, the Print Parameter List selection will be automatically reset to N.
❏ If you only want to print the configuration parameters covered in this section, you can print the Self Test sheet instead. The Self Test is described in Section 2.
Print Parameter List SPrint Parlist=N*
AXIS HP MIO User’s Manual 27
Section 3: Configuration
System language Page lenght Emulation
This page is intentionally blank
28 AXIS HP MIO User’s Manual
Section 4: Advanced Functions
1001010100111 11010001001 010011101
Section 4 Advanced Functions
This section deals with some of the AXIS HP MIO functions that brings your HP printer beyond the normal IBM printer emulation. It is only intended as an overview – for a complete description of these functions, please refer to the AXIS HP MIO Technical Reference.
The functions covered in this manual are:
• Configuration from the System
This is an alternative method for changing the front panel configuration parameters, and for changing parameters not available from the front panel. You may send a file containing the configuration commands either from your IBM system, or from a local PC.
• Hex Transparency
This function allows you to use all the HP printer features in the IBM system environment.
• Font Selection
The font commands provides easy access to the printer resident PCL fonts from your IBM system documents.
Note: ❏ If you intend to use any of these functions, we strongly recommend that you order the AXIS HP MIO Technical Reference from your distributor. The Technical Reference also describes a wide range of additional functions to further enhance your printouts.
AXIS HP MIO User’s Manual 29
Section 4: Advanced Functions
1001010100111 11010001001 010011101
Configuration from the System
For printers without a front panel, you can configure the AXIS HP MIO by inserting configuration commands in your document. The example below shows a configuration sequence that sets all front panel parameters to their default values (US version; for the European version, substitute LETTER with A4):
Example:
Note that page orientation and size may be set individually for each input bin, while the front panel parameters affect all available bins simultaneously.
A common application is to print on pre-printed forms from the lower bin, while printing standard jobs from the upper bin. To do this, you may need to turn off the COR (Computer Output Reduction) function for the lower bin:
Example:
%AXIS+%CONFIG+SYSL = 37;PREMUL = 3816;MPL = 66;AUTORI = YES;BIN1 = COR,LETTER;BIN2 = COR,LETTER;BIN3 = COR,LETTER;BIN4 = COR,LETTER;BIN5 = COR,LETTER;SAVE;%CONFIG-
%AXIS+%CONFIG+BIN2 = PORT,LETTER;SAVE;%CONFIG-
30 AXIS HP MIO User’s Manual
Section 4: Advanced Functions
1001010100111 11010001001 010011101
Hex Transparency
The transparency function allows you to send ASCII data to the printer directly from the host application. The data may be of any language supported by the printer, e.g. PCL, HP-GL, or PostScript. This gives you access to all the HP printer features from within the IBM environment.
When the percent and less-than characters (%<) are received, the AXIS HP MIO will switch over to hex transparency mode. Following data (hexadecimal byte values or quoted text) are passed directly to the printer without any conversion. The hex transparency mode continues until the greater-than and percent characters (>%) are received.
Example:The example below shows how to embed ‘start underline’ (EC
&d0D) and ‘stop underline’ (EC &d@) commands in your documents:
Resulting printout:
The word %<1B26643044>%underline%<1B266440>% is underlined.You may use %<1B,"&d0D">%quoted text%<1B,"&d@">% as well.
The word underline is underlined.You may use quoted text as well.
AXIS HP MIO User’s Manual 31
Section 4: Advanced Functions
1001010100111 11010001001 010011101
This is a more advanced example, showing how to draw a rectangle using HP-GL commands:
This is what it does line-by-line: (1) – Start transparency (%<), reset printer (EC E), and enter HP-GL mode (EC %0B), (2) – Draw the rectangle, and (3) – Resume PCL mode (EC %0A), reset printer (EC E), and stop transparency (>%).
Please refer to your printer manual (Technical Reference) for a description of the HP-GL commands.
When experimenting with HP-GL or PostScript functions, don’t forget to resume PCL mode and reset the printer afterwards!
Font Selection
Fonts can be selected by the system in two ways: directly by font reference (FGID number), or indirectly by pitch selection (CPI). The FGID selection is only available in Twinax mode.
In order to gain full access to the PCL fonts in both Coax and Twinax mode, the AXIS HP MIO offers an alternative font selection command.
Font selection commands may be included anywhere in your documents. They begin with ‘percent-slash’ (%/) followed by the word FONT and the font (FGID) number. An optional point size value preceeded by a comma may be included. The command is ended with a semi-colon (;).
1:2:3:
%<1B,"E",1B,"%0B","IN;SP1;PA0,0;EA2500,1500;"1B,"%0A",1B,"E">%
32 AXIS HP MIO User’s Manual
Section 4: Advanced Functions
1001010100111 11010001001 010011101
Example:The following example shows how to select a 10 CPI (fixed pitch) italic font, and a scalable (proportional) font in 18 points.
• A font command starts with %/ and ends with ;.
• 18 and 6199 are the FGID (Font Global Identifier) numbers specifying the fonts. See Appendix C for a complete list of the supported FGIDs.
• 180 is a Point Size parameter used for scaling the font. The value is entered as ten times the desired point size.
Resulting printout:
Notes: ❏ If Point Size is omitted, 10 points will be used as default for all scalable fonts.
❏ Fixed pitch fonts are not scalable. If a Point Size is specified, it will be used to compress/expand the font. ( %/FONT 18,105; will compress the 10 CPI font to 10.5 CPI without changing the size of the characters).
❏ If a Point Size is specified for a PSM font (see Appendix C), only the inter-word spacing will be affected. The default space width equals a 12 CPI space.
%/FONT 18;This is 10 CPI Courier italic%/FONT 6199,180;This is 18 pt Palatino
AXIS HP MIO User’s Manual 33
Appendix A: The AXIS HP MIO Rear PanelHP MIO
Appendix A The AXIS HP MIO Rear Panel
The rear panel has two indicators (SYSTEM and PC SHARE), a rotary switch, a Coax/Twinax switch, and two connectors. The larger connector (PARALLEL) is used for local PC or LAN print server input, and smaller circular is used for Coax/Twinax input.
The picture below shows the rear panel with its indicators, switches, and connectors.
The AXIS HP MIO Rear Panel
The System Indicator
This indicator (green) is lit when the AXIS HP MIO is connected to the IBM system. It can also flash in the following cases:
• At power-up (for a few seconds).
• When Test Mode is entered, see below.
• During test function execution (rapid flash).
34 AXIS HP MIO User’s Manual
Appendix A: The AXIS HP MIO Rear PanelHP MIO
The PC SHARE Indicator
This indicator (yellow) is lit during a local PC or LAN printout. Host printouts will be held waiting until the PC/LAN printout is completed.
The Rotary Switch
The ten-position rotary switch is used for setting the AXIS HP MIO device address (this applies to 5250/Twinax mode only – the switch should always be in zero position in 3270/Coax mode).
The switch is also used for accessing Test Mode functions.
The Coax/Twinax Switch
This switch (CX/TX) configures the AXIS HP MIO hardware for Coax or Twinax mode operation. It should be set prior to the installation. Do not alter this switch when the printer is powered on or connected to the IBM system.
Test Mode
The Test Mode is used for accessing internal AXIS HP MIO functions. Entering Test Mode makes the AXIS HP MIO go off-line towards all connected input sources, so you do not have to disconnect any cables.
AXIS HP MIO User’s Manual 35
Appendix A: The AXIS HP MIO Rear PanelHP MIO
Set the rotary switch to position 9 to enter Test Mode. When the SYSTEM indicator starts to flash, select one of the following functions:
Caution 5250/Twinax Users: Don’t forget to set the rotary switch to the device address after exiting Test Mode.
Notes: ❏ To set factory default configuration, a two-step operation is required in order to avoid accidental activation and loss of configuration settings. When position 1 is selected, the yellow PC SHARE indicator begins to flash. To confirm this selection, switch to position 2 within two seconds.
❏ The Hex Dump modes are useful when analyzing incorrect printouts, but be careful – they can consume huge amounts of paper! Refer to the AXIS HP MIO Technical Reference for details.
❏ The Terminal Configuration Utility provides an easy-to-use method of customizing the AXIS HP MIO board using a directly attached IBM 5250/3270 display station. Refer to the AXIS HP MIO Technical Reference for details.
Position Test Mode Function
0 Reserved
1 Set Factory Defaults – abandon the current configuration
2 Confirm Factory Defaults – see note below
3 ASCII Hex Dump Mode – print the outgoing data stream as hexadecimal values
4 System Hex Dump Mode – print the incoming data stream as hexadecimal values
5 Reserved
6 Reserved
7 Terminal Configuration – run the Configuration Utility on an IBM display station
8 Print Parameter List – print the complete configuration
9 Exit Test Mode – resume normal print operation
36 AXIS HP MIO User’s Manual
Appendix B: System Configuration GuidelinesHP MIO
Appendix B System Configuration Guidelines
This appendix contains technical details for the system operator on how to configure the IBM system for the AXIS HP MIO board.
5250/Twinax Host Configuration
The AXIS HP MIO is, by default, set to emulate the IBM 3816 01S/01D printer with 5219 software. This setting is recommended for any 5250 system, as it makes the best use of the functionality of the HP printer.
5256 may be used when you need to guarantee that the AS/400 will not send format settings (CPI, LPI, etc.). This is useful when you use Hex Transparency to control printer behaviour.
AS/400 Configuration If you will configure for a number of AXIS HP MIO interfaces, or if you will use IBM 3812 emulation, manual configuration is recommended. Manual configuration is performed using CRTDEVPRT or WRKDEVD F6 (Create).
You may, prior to configuration, use PRTDEVADR to get a chart showing free port and switch setting combinations. Device type (TYPE) and Device model (MODEL) must match the setting of AXIS HP MIO. The printers are listed in functionality order, with 5256 being the least functional (advanced) of the IBM printer emulations.
AXIS HP MIO printer emulation Device type Device model
IBM 5256 5256 1
IBM 5224 5224 1
IBM 5225 5225 1
IBM 4214 4214 2
IBM 4230 4214 2
IBM 3812 3812 1
IBM 3816 3812 1
AXIS HP MIO User’s Manual 37
Appendix B: System Configuration GuidelinesHP MIO
S/36 Configuration If you will configure for a number of AXIS HP MIO interfaces, manual configuration is recommended.
Manual configuration is performed using CNFIGSSP.
The device code must match the setting of AXIS HP MIO:
S/38 Configuration If you will configure for a number of AXIS HP MIO interfaces, manual configuration is recommended. Manual configuration is performed using CRTDEVD.
Device type (DEVTYPE) must match the setting of AXIS HP MIO:
AXIS HP MIO printer emulation Device code
IBM 5256 PB
IBM 5224 PC
IBM 5225 PC
IBM 4214 PG
IBM 4230 PG
IBM 3812 PD
IBM 3816 PD
AXIS HP MIO printer emulation Device type
IBM 5256 5256
IBM 5224 5224
IBM 5225 5225
IBM 4214 4214
IBM 4230 4214
IBM 3812 3812
IBM 3816 3812
38 AXIS HP MIO User’s Manual
Appendix B: System Configuration GuidelinesHP MIO
3270 Host Configuration
The AXIS HP MIO board supports non-SNA (LU-0) 3270 DSC, SNA LU-3 3270 DSE, and SNA LU-1 SCS data streams.
When printing in an SNA network, VTAM needs to be set up, depending on desired LU type. The following VTAM logon-mode entries apply to MVS, VM, and VSE.
The logon-mode entries are the same for all emulated IBM printers (selected by the AXIS HP MIO IBM Printer Emulation parameter)
SNA LU-1 SCS:
SNA LU-3 3270 DSE:
(Continuation characters in column 72 are not shown)
You also need to match the Printer Emulation setting in AXIS HP MIO with the setting of your 3270 printer driver software (JES/328x, VPS, CMA-Spool, RSCS, etc.).
If there is no selection for 4224, 4230, 3812, or 3816, you can instead select 3268.
SCS MODEENT LOGMODE=SCS,FMPROF=X'03',TSPROF=X'03',PRIPROT=X'B1', SECPROT=X'90',COMPROT=X'3080',RUSIZES=X'87C6', PSERVIC=X'01000000E100000000000000', PSNDPAC=X'01',SRCVPAC=X'01'
DSC4K MODEENT LOGMODE=DSC4K,FMPROF=X'03',TSPROF=X'03',PRIPROT=X'B1', SECPROT=X'90',COMPROT=X'3080',RUSIZES=X'8787', PSERVIC=X'03000000000018502B507F00'
AXIS HP MIO User’s Manual 39
Appendix C: Fonts
Appendix C Fonts
This appendix lists all the 130 IBM fonts supported by the AXIS HP MIO. Fonts are selected by FGID (Font Global Identifier) as outlined in Section 4. Each IBM font is mapped to a printer resident PCL font, selected to make a close match to the original IBM font. The IBM to PCL font mapping is controlled by the Font Definition Table. All entries in this table are fully editable, and you can also add new entries. Refer to the AXIS HP MIO Technical Reference for further information.
10 CPI Fonts
FGID IBM FONT NAME
3 OCR-B
5 Orator
11 Courier 10
12 Prestige Pica
13 Artisan 10
18 Courier Italic 10
19 OCR-A
20 Pica
30 Math Symbol 10
38 Orator Bold
39 Gothic Bold 10
40 Gothic Text 10
41 Roman Text 10
42 Serif Text 10
43 Serif Italic 10
46 Courier Bold 10
60 Prestige Bold 10
12 CPI Fonts
FGID IBM FONT NAME
66 Gothic Text 12
68 Gothic Italic 12
69 Gothic Bold 12
70 Serif Text 12
71 Serif Italic 12
72 Serif Bold 12
80 Math Symbol 12
84 Script
85 Courier 12
86 Prestige Elite
87 Letter Gothic 12
91 Light Italic 12
108 Courier Bold 12
110 Letter Gothic Bold
111 Prestige Elite Bold
112 Prestige Elite Italic
40 AXIS HP MIO User’s Manual
Appendix C: Fonts
AXIS HP MIO User’s Manual 41
Proportional PSM Fonts
FGID IBM FONT NAME
155 Boldface Italic
158 Modern
159 Boldface
160 Essay
162 Essay Italic
163 Essay Bold
173 Essay Light
175 Document
13.3 CPI Fonts
FGID IBM FONT NAME
204 Gothic Text 13
15 CPI Fonts
FGID IBM FONT NAME
221 Prestige 15
223 Courier 15
225 Math Symbol 15
229 Serif Text 15
230 Gothic Text 15
5 CPI Fonts
FGID IBM FONT NAME
244 Courier 5
245 Courier Bold 5
17 CPI Fonts
FGID IBM FONT NAME
252 Courier 17
253 Courier Bold 17
254 Courier 17 (sub/super)
18 CPI Fonts
FGID IBM FONT NAME
258 Courier 18
8 CPI Fonts
FGID IBM FONT NAME
266 Courier Bold 8
20 CPI Fonts
FGID IBM FONT NAME
281 Gothic Text 20
25 CPI Fonts
FGID IBM FONT NAME
289 Gothic Text 25
26.7 CPI Fonts
FGID IBM FONT NAME
290 Gothic Text 27
Proportional Typographic Fonts
(Fixed Point Size)
FGID IBM FONT NAME
751 Sonoran-Serif 8-pt Roman Medium
1051 Sonoran-Serif 10-pt Roman Medium
1053 Sonoran-Serif 10-pt Roman Bold
1056 Sonoran-Serif 10-pt Roman Italic Medium
1351 Sonoran-Serif 12-pt Roman Medium
1653 Sonoran-Serif 16-pt Roman Bold
2103 Sonoran-Serif 24-pt Roman Bold
Appendix C: Fonts
Proportional Typographic Fonts
(Scalable – User Defined FGIDs)
FGID PCL FONT NAME
3840 CG Times
3841 CG Times Bold
3842 CG Times Italic
3843 CG Times Bold Italic
3844 CG Omega
3845 CG Omega Bold
3846 CG Omega Italic
3847 CG Omega Bold Italic
3848 Coronet
3849 Clarendon Condensed
3850 Univers Medium
3851 Univers Bold
3852 Univers Medium Italic
3853 Univers Bold Italic
3854 Univers Medium Condensed
3855 Univers Bold Condensed
3856 Univers Medium Condensed Italic
3857 Univers Bold Condensed Italic
3858 Antique Olive
3859 Antique Olive Bold
3860 Antique Olive Italic
FGID PCL FONT NAME
3861 Garamond Antiqua
3862 Garamond Halbfett
3863 Garamond Kursiv
3864 Garamond Kursiv Halbfett
3865 Marigold
3866 Albertus Medium
3867 Albertus Extra Bold
3868 Arial
3869 Arial Bold
3870 Arial Italic
3871 Arial Bold Italic
3872 Times New
3873 Times New Bold
3874 Times New Italic
3875 Times New Bold Italic
3876 Symbol
3877 Wingdings
42 AXIS HP MIO User’s Manual
Appendix C: Fonts
Proportional Typographic Fonts
(Scalable Point Size)
FGID IBM FONT NAME
5687 Times Roman
5707 Times Roman Bold
5815 Times Roman Italic
5835 Times Roman Bold Italic
6199 Palatino
6219 Palatino Bold
6327 Palatino Italic
6347 Palatino Bold Italic
16951 Century Schoolbook
16971 Century Schoolbook Bold
17079 Century Schoolbook Italic
17099 Century Schoolbook Bold Italic
33335 Optima
33355 Optima Bold
33463 Optima Italic
33483 Optima Bold Italic
33591 Futura Book
33601 Futura Heavy
33719 Futura Book Italic
33729 Futura Heavy Italic
34103 Helvetica
34123 Helvetica Bold
34231 Helvetica Italic
34251 Helvetica Bold Italic
41783 Cursive
41803 Cursive Bold
41911 Cursive Italic
41931 Cursive Bold Italic
AXIS HP MIO User’s Manual 43
Appendix D: Technical SpecificationsHP MIO
Appendix D Technical Specifications
IBM 5250 Features
Host Environments IBM System/34, IBM System/36, IBM System/38, IBM AS/400
Attachments IBM 5259 Migration Data Link, IBM 5294 Control Unit, IBM 5394 Control Unit, IBM 5494 Control Unit, IBM 5251 model 12 Control Unit, IBM 5299 Terminal Multiconnector
Printer Emulations IBM 3812 models 1 and 2 with 5219 software, IBM 3816 models 01S and 01D with 5219 software, IBM 4214 model 2, IBM 5224 models 1 and 2, IBM 5225 models 1 - 4, IBM 5256 models 1 - 3, IBM 4230 model 101
System Features SCS and FFT data streams, Virtual Printer PC/Support, Multiple Bin Support, 19 National Languages, Page Presentation Media, Computer Output Reduction, Duplex, Page Rotation in four orientations, FGID Font Selection, Fixed-pitch, Proportional, and Typographic Fonts, Scalable font support
IBM 3270 Features
Host Environments IBM S/370, S/390, IBM 303x, 308x, 309x, IBM 81xx, IBM 47xx, IBM 43xx, IBM 937x
Attachments IBM 3174 Control Unit, IBM 3274 type A Control Unit, IBM 3276 Control Unit Display System, IBM 4701/4702 Device Cluster Adapter, IBM 4300 Printer Adapter, IBM 9370 Subsystem Control Unit, IBM 3299 Multiplexor
Printer Emulations IBM 3812 model 1, IBM 3816 model 01S and 01D, IBM 3287 model 2C, IBM 3268 models 3 and 13, IBM 4214 model 1, IBM 4224 model 2 (non-IPDS), IBM 4230 model 201
System Features SNA SCS (LU-1), SNA DSE (LU-3), and BSC, 3270/DSC data streams, APL2/Text Feature, LU-1 FM Headers Subset 1, SCS Local/Remote Save/Restore Formats, Extended Attribute Buffer (EAB), 3270/DSC/DSE Query Reply and LU-1 Query List, IBM RPQs, Load Translate Table, Country Extended Code Pages (CECP), Page Presentation Media, Computer Output Reduction, Scalable font support
44 AXIS HP MIO User’s Manual
Appendix D: Technical SpecificationsHP MIO
Additional Features • Configuration from the front panel, IBM system, local PC, or IBM Display Station
• Fully editable character translation tables• Programmable Hex Transparency function• 255 User Definable Strings• 127 programmable string substitutions• 130 predefined fonts• Scalable font selection through FGID and Point Size• Automatic printer sharing functions• System and ASCII hex dump modes• Bar Codes
Supported Printers • HP LaserJet 5Si• HP LaserJet 4(+), HP LaserJet 4V, HP LaserJet 4Si• HP LaserJet IIISi• HP DesignJet 600/650C, HP DeskJet 1200C/1600C• HP PaintJet XL300, HP Color LaserJet• Any HP or compatible with MIO expansion slot
Dimensions 50 x 30 x 130 mm / 6.0 x 1.2 x 5.1 inches
Weight 0.22 kg / 0.48 lb
Power Max. 150 mA @ 5V DC (supplied from the printer)
Approvals
EMI EN 55022/1987, EN50082-1/1992. FCC Class A.
Safety All safety regulations according to HP printer specifications
Environmental
Temperature 5 - 40 °C / 40 - 105 °F
Humidity 20 - 80% non-condensing
All specifications are subject to change without prior notice
AXIS HP MIO User’s Manual 45
Appendix E: How To Contact AxisHP MIO
Appendix E How To Contact Axis
Technical Support If you need technical support, please contact your dealer. If they can’t help you, they will forward your request to us.
Axis on-line service
Use the Axis on-line service at any time to retrieve electronically distributed items. The material available includes the HP MIO Technical Reference, the Adobe Acrobat Reader (required for all Axis on-line documentation), company and product presentations, etc. All items are available on Internet by a WWW browser or FTP file transfer, and on the Axis Bulletin Board.
Internet andWorld Wide Web
If you are connected to Internet, have a look at the Axis WWW Home Page at http://www.axis.se/or http://www.axisinc.com/. Where you will find information about the company and our products. You can also down-load on-line manuals and tools such as the Acrobat Reader for different platforms. You can also get files and information through anonymous ftp: log in to ftp.axis.se or ftp.axisinc.com and go to the /pub/axis directory, or enter ftp://ftp.axis.se/pub/axis or ftp://ftp.axisinc.com/pub/axis in your WWW browser.
The Axis BulletinBoard System
Another way to access the Axis archive is the Axis BBS. You will need a high-speed modem, a VT100 or VT220 terminal emulator, and a Kermit or ZModem compatible software. Dial +46 46 12 06 32 or +46 46 211 94 53 and log in as guest (no password required).
46 AXIS HP MIO User’s Manual
Appendix E: How To Contact AxisHP MIO
The Axis Offices To contact an Axis office, choose the one nearest to your region:
Europe, Middle East,South America,Africa, Australia
Axis Communications ABScheelevägen 16S-223 70 Lund, SwedenPhone: +46 46 270 18 00Fax: +46 46 13 61 30Email: [email protected]
North & CentralAmerica
Axis Communications Inc.4 Constitution Way, Suite G, Woburn, MA 01801-1030, USAPhone: 1-800-444-AXIS, (617) 938-1188Fax: (617) 938-6161Email: [email protected]
Japan Axis Communications K.K.8th Center Plaza 5F, 1-10-16 Nihombashi Horidome-cho,Chuo-ku, Tokyo 103, JapanPhone: +81 3 3663 8801Fax: +81 3 3663 8802Email: [email protected]
Hong Kong, Asia(except Japan &
Middle East)
Axis Communications Ltd.Room 602, Asian House, Hennessy Road, Wanchai, Hong KongPhone: +852 2836 0813Fax: +852 2573 5935Email: [email protected]
AXIS HP MIO User’s Manual 47
Appendix F: Related Documentation
48 AXIS HP MIO User’s Manual
HP MIO
Appendix F Related Documentation
TITLE PART NO.
AXIS HP MIO Technical Reference 13364
AXIS Support Reference Manual 13083
IBM System/36 Functions Reference Guide SA21-9436
IBM System/38 Service Guide SY31-0523
IBM AS/400 Programming: Guide to Programming for Printing SC21-8194
IBM AS/400 Printing GG24-3452
IBM AS/400 Device Configuration Guide SC41-8106
IBM 3274 Control Unit Customizing Guide GA23-0065
IBM 3174 Subsystem Control Unit Customizing Guide GA23-0214
IBM 3174 Character Set Reference GA27-3831
IBM 3816 Page Printer Reference for AS/400, S/36, or S/38 GA34-2084
IBM 3812 and 3816 Page Printers Programming Reference for 3270 Information Display System Attachment
GA34-2081
IBM 3812 and 3816 Page Printers Font Reference GA34-2111
VTAM Customisation SC23-0112