. . . presents presents

SERIES 800 MOMENT BALANCE

SYSTEM

SERIES 800 MOMENT BALANCE

SYSTEM

Nobody Knows Moment Weighing Like AWS

Unique System to Moment Weigh a SPHERE

Connecting RodsEngine Blades

FanTurbineRotorCompressor

Customers Depend on AWS

More Than 30 Years Experience in Moment Weighing

Systems That Were Installed in the 1970’s Are Still Operational

Low MaintenanceIncreased Productivity

GE Aircraft Engines Group

Proved the AWS Method is Most Accurate

AWS Equipment Specified For ALL FacilitiesEngine BladeEngine AssemblyEngine

Maintenance

So reliable is AWSequipment, that in 1982GE awarded a Class 0ne, Group One QC CodeRating; making AWS a self-certified vendor.

PRATT & WHITNEY AIRCRAFT

Engine Blades Manufactured by:HOWMET CorporationI.E.P.I.TURBO PRODUCTSNEW ENGLAND AIR FOIL

Approved for Use on all P&W Engines

U.S. Air ForceU.S. Air ForceUnits in

Service:

Kelly AFB (3) Travis AFB (2) Altus AFB Dover AFB

Engine Maintenance

& Overhaul

Total Time to Balance an Engine Reduced by More Than 30%

BLADE MOMENT BALANCE

BASE ASSEMBLY

Tubular Steel Construction

Sand Filled to Eliminate “Ringing”

Adjustable Feet for Leveling

Custom HOUSING

Eliminates Air Currents About the System

LEXAN and Aluminum Tube Construction

Sliding Doors Allow Full Access

Time Proven AWS Weigh Cell

Patented Mass Balance, Hydraulic Dampening

Readings Obtained in Less Than 150 Milli-seconds

Accuracy to 0.01% of Full Scale

Counterbalanced for Tooling and “Master” Load

SCALE Assembly

RANGE OPTIONSRANGE OPTIONS

GRAM / INCHES OUNCE / INCHESMODEL RANGE TOTAL

CAPACITYRANGE TOTAL

CAPACITY802 1,500 15,000 50.00 500.00803 2,000 20,000 80.00 800.00804 5,000 50,000 150.00 1,500.00806 10,000 100,000 300.00 3,000.00808 20,000 200,000 800.00 8,000.00

808/EX 20,000 300,000 800.00 12,000.00

RESOLUTION = 0.001% of TOTAL CAPACITY

CUSTOM Designed & Manufactured Blade

ToolingDesigned to Critically Hold Blade

as It Will Be InstalledActual Moment As If Installed In

Disk AssemblyMatched to Scale For Superior

Accuracy

CRADLE Assembly

Computer Configuration Pentium VI Compatible or Better MS/DOS 6.22 1 Serial Port

– 1 (9 Pin) for the Input From the Scale

2 Parallel Ports– 1 for the Label Printer– 1 for the Report Printer

Moment Software(version 2007)

Interactive Prompts for Each Operation

Part Data Entry/Modification in Less Than a Minute

All Settings Password Protected From Unauthorized Changes

Prompted Scale Set-Up and Calibration

Ease of Use

Minimal Time for Part Selection & Changeover

Four Screws to Remove & Replace The Cradle

Menu Selection to Change Software Part Specifications

Reference the “MASTER” for the New Part

Limited Operator Data Input Eliminates Transcription and Entry

ErrorsAUTOMATIC Data RecordingIndividual Piece Serial NumberingOperator IDMeasurement Result

Part Sorting and Data Retrieval

Sort to Groups Sort for Matched Pairs Sort Pairs to Matched Sets Absolute Sort of Complete

Assembly Data to Labels, Reports, and Files

THEORY OF OPERATION The MOMENT is Measured

From the Centerline of the Assembly, Rather Than Some Arbitrary Point .

Computes the “MOMENT” by Determining the Difference (plus or minus 10% of the Total) from the MASTER or OPTIMUM Blade Moment..

RESULT: The AWS Method Renders Results That Are At Least 10 Times More Accurate Than Other Methods Of Moment Determination.

MOMENT is a factor of the mass of the part, times the distance of the Center of Mass from the Centerline of the Scale Assembly

OPERATIONAfter the the System Setup, The

Operator Follows These Steps: Enters Individual Operator ID Selects the Part to be Measured Inserts a “MASTER” Blade into the

Cradle for Referencing Removes the “MASTER,” Inserts a

Part to be Measured

After Closing the Housing Doors, Allows the Scale to Settle, Pushes the

F5 Key, Enters the Part Serial Number and Press the ENTER Key

The Label is Printed and the Measurement Data is Saved to a File

The Operator Continues Inserting Parts Until a Sufficient Number for Accurate Classification Have Been Measured

The Entire Process of Loading a Part intothe Cradle, Closing the Housing Door, Measuring the Part, Removing It, and Affixing the Label; Takes Less Time ThanIt Is Taking Me to Tell You About It!

Cost BenefitsIncreased Productivity Up to 10 Parts Per Minute Limited Operator Data Entry Between

Parts One Scale Can Measure Several Parts More Than 35% Reduction in TOTAL Time

to Balance an Engine

Economical Operation 115 VAC/60Mhz Power

Minimum Operator Training Required

Advantages of the AWS System

Unmatched AccuracyMechanically Provable “In the Field”Ease of UseSelectable Part Sorting MethodsIncreased ProductivityEconomy of Operation

TO FIND OUT MORE, Contact:

Inside Sales: Advance Weight Systems, Inc.

409 North Main Street; P.O. Box 6

Grafton, OH 44044Telephone: (440) 926-3691FAX: (440) 926-2142

http://www.advancew8.com