Prisma MediaCenter Unified Management Agent (UMA) Installation Instructions Overview Introduction This document provides an overview of the Unified Management Agent (UMA) and lists the products that will support UMA. For users who already have Prisma® FiberLinX modules, this document also identifies the system requirements for upgrading to UMA and provides a brief overview of the upgrade process. This document is intended for authorized service personnel who have experience working with similar equipment. The service personnel should have appropriate background and knowledge to complete the procedures described in this document. Safe Operation for Software Controlling Optical Transmission Equipment If this manual discusses software, the software described is used to monitor and/or control ours and other vendors’ electrical and optical equipment designed to transmit video, voice, or data signals. Certain safety precautions must be observed when operating equipment of this nature. For equipment specific safety requirements, refer to the appropriate section of the equipment documentation. For safe operation of this software, refer to the following warnings. WARNING: Ensure that all optical connections are complete or terminated before using this equipment to remotely control a laser device. An optical or laser device can pose a hazard to remotely located personnel when operated without their knowledge. Allow only personnel trained in laser safety to operate this software. Otherwise, injuries to personnel may occur. Restrict access of this software to authorized personnel only. Install this software in equipment that is located in a restricted access area.
Introduction This document provides an overview of the Unified Management Agent (UMA) and lists the products that will support UMA. For users who already have Prisma® FiberLinX modules, this document also identifies the system requirements for upgrading to UMA and provides a brief overview of the upgrade process.
This document is intended for authorized service personnel who have experience working with similar equipment. The service personnel should have appropriate background and knowledge to complete the procedures described in this document.
Safe Operation for Software Controlling Optical Transmission Equipment If this manual discusses software, the software described is used to monitor and/or control ours and other vendors’ electrical and optical equipment designed to transmit video, voice, or data signals. Certain safety precautions must be observed when operating equipment of this nature.
For equipment specific safety requirements, refer to the appropriate section of the equipment documentation.
For safe operation of this software, refer to the following warnings.
WARNING:
Ensure that all optical connections are complete or terminated before using this equipment to remotely control a laser device. An optical or laser device can pose a hazard to remotely located personnel when operated without their knowledge.
Allow only personnel trained in laser safety to operate this software. Otherwise, injuries to personnel may occur.
Restrict access of this software to authorized personnel only.
Install this software in equipment that is located in a restricted access area.
2 4015100 Rev B
Overview
Qualified Personnel Only appropriately qualified and skilled service personnel should attempt to install, operate, maintain, and service this product.
WARNING:
Allow only qualified and skilled personnel to install, operate, maintain, and service this product. Otherwise, personal injury or equipment damage may occur.
4015100 Rev B 3
Products that Support UMA
Products that Support UMA The following product groups support UMA:
Prisma FiberLinX series (10/100 and Gigabit versions)
Future Prisma modules that have on-board SNMP management
Prisma MediaCenter series (6-slot and 20-slot models) with an SNMP management module
Each of the devices listed above has its own SNMP agent. FiberLinX modules have on-board intelligence, while Prisma MediaCenters use an SNMP module for management.
Notes:
UMA is not applicable to Prisma modules that do not have on-board SNMP management.
UMA is not available on previous models of SNMP-manageable chassis, such as the 2-slot and 8-slot Prisma MediaCenter chassis.
In this document, unless noted otherwise, “FiberLinX” and “Prisma FiberLinX” refer to both Prisma FiberLinx (10/100) and Prisma GigaFiberLinX (Gigabit).
For specific UMA usage requirements, see Requirements for Upgrading to UMA Compatibility (on page 6).
4 4015100 Rev B
UMA Overview
UMA Overview The Unified Management Agent allows users to manage all modules installed in a Prisma MediaCenter, including those with on-board intelligence, with a single IP address and from a central location. Using UMA requires only a single, dedicated management port. By not requiring separate SNMP connections for each device means, UMA conserves the usage of switch ports.
Although each FiberLinX has its own agent, UMA lets users manage any or all FiberLinX modules installed at the Central Office (CO). When deploying FiberLinx units in pairs between the CO and remote sites (CPE), each Host FiberLinX takes over the SNMP duties for itself and its Remote FiberLinX. Thus, UMA enables users to manage multiple FiberLinX units from the single IP address of the chassis at the CO.
Suppose that there are 20 FiberLinX modules installed in a Prisma MediaCenter/20 at the CO, each connected to a Remote FiberLinX. With this arrangement, UMA lets users manage all 41 devices (20 Host-FiberLinX and 20 Remote-FiberLinX, plus the chassis itself) with the single IP address assigned to the Prisma MediaCenter. Alternatively, users could assign separate IP addresses to each FiberLinX and manage them independently, if desired. UMA offers management flexibility.
Note: UMA is not applicable when using the FiberLinX only at the Customer Premises (CPE).
4015100 Rev B 5
How UMA Works
How UMA Works
With UMA When an SNMP request for a FiberLinX comes in, the Prisma MediaCenter passes the request to the SNMP agent in the desired module. The FiberLinX provides the SNMP response, which is then routed through the Prisma MediaCenter and supplied to PrismaView™ or another SNMP management application.
Without UMA When an SNMP request for a FiberLinX comes in, the Prisma MediaCenter cycles through each slot, checking for FiberLinX modules. The Prisma MediaCenter sees FiberLinX modules in the chassis, but does not manage them. Management for each FiberLinX requires a separate connection and a separate IP address. Although users can select each FiberLinX in the chassis, the Prisma MediaCenter cannot manage it directly.
Easy Upgrades With UMA UMA lets users easily upgrade any or all FiberLinX modules in a chassis with just a few mouse clicks. For additional information regarding File Management for upgrading firmware, refer to the Administration Tab in the iConfig Help file.
In addition, while upgrades are in process, all devices in the chassis are fully functional. When a firmware code upgrade is needed, the user initializes an upgrade task via PrismaView to update the Host FiberLinX firmware. The Host FiberLinX then sends a copy of the new firmware to the Remote FiberLinX. The Remote FiberLinX upgrades the new code via Upgrade Task.
6 4015100 Rev B
UMA Compatibility Upgrade Process
UMA Compatibility Upgrade Process Most FiberLinX modules in the field are upgradeable, but not all are upgradeable to work with UMA. A utility called the Batch Upgrader lets users easily determine whether a particular FiberLinX module is upgradeable. This section describes the process of using the Batch Upgrader utility.
Requirements for Upgrading to UMA Compatibility The hardware and software requirements for compatibility with the Unified Management Agent are as follows:
Software
- PrismaView 1.8 or higher
Device firmware (Flash PROM)
- Prisma MediaCenter firmware 953-00 B0 or higher
- Prisma FiberLinX firmware 511-01 C0 or higher
- Prisma Giga-FiberLinX firmware 860-00 B0 or higher
Additional Requirements
- Some FiberLinX units will require updates to hardware and firmware (not Flash PROM firmware) which are only upgradeable by an appointed technician. See Using the Batch Upgrader (on page 6) for details.
Note: iConfig can confirm the version of Flash PROM firmware. The Batch Upgrader can confirm if Prisma FiberLinX units are upgradeable for UMA compatibility.
Once all of the elements listed above are upgraded, UMA is available and is enabled for compatible products. However, users can still choose to manage FiberLinX units independently rather than use UMA functionality.
Batch Upgrader Utility Tool The Batch Upgrader utility software application allows users to upgrade the Flash PROM firmware of multiple devices. The Batch Upgrader can also assist in the initial transition to UMA compatibility. The Batch Upgrader can determine whether Prisma FiberLinX modules are capable of being upgraded to UMA compatibility, and will indicate the action(s) required for the upgrade.
Using the Batch Upgrader Following is a brief overview of the upgrade process. For detailed information on using the Batch Upgrader, see the Batch Upgrader Help file.
4015100 Rev B 7
UMA Compatibility Upgrade Process
1 Create the list of items to upgrade. The list can be created in the Batch Upgrader or imported from PrismaView, and can include devices of multiple types (i.e., Prisma MediaCenter, PrismaFiberLinX, PrismaGiga-FiberLinX, etc.). However, users can only Batch Upgrade devices that use the same flash PROM. A separate Batch Upgrade must be performed for each device (flash PROM) type.
2 Validate the list of items to upgrade. This checks the PROM name and date to confirm that the device can communicate with the Batch Upgrader before attempting an update. Each device must be validated before adding it to the upgrade list. We also recommend validating all Prisma FiberLinX devices for UMA compatibility. Once the validation process is complete, the Status field in the Batch Upgrader screen updates to show the results for each device. In the Status field:
The word Validated indicates that the device will communicate with the Batch Upgrader.
A code such as 09-03920-03-REMOTE indicates the degree of UMA compatibility.
In the example shown below, all three devices were able to communicate with the Batch Upgrader.
The Status Legend, accessible from the Batch Upgrader Help menu, identifies the meanings of the UMA compatibility codes in the Status field.
8 4015100 Rev B
UMA Compatibility Upgrade Process
For example, according to the Status Legend, the code 09-03920-03-HOST in the example above indicates that the tested device is not UMA compatible as a host.
Notes:
For PrismaFiberLinX units that are non-upgradeable (i.e. not UMA capable as host), we recommend removing them from the CO and installing at a CPE or reserving them for future CPE expansion.
Contact Technical Support if the FiberLinX units require the additional hardware and/or firmware updates. See Support Telephone Numbers (on page 11) for contact information.
3 Make sure the flash PROM file for the Upgrade is correct.
4 Upgrade, if desired. Select each device in the list to upgrade. All selected devices must use the same PROM. Once the upgrade is performed, the Status field in the Batch Upgrader will show whether each device was successfully upgraded.
Using UMA to Upgrade Flash PROM Firmware Once the devices are upgraded and are UMA compable, use UMA’s File Management functionality to easily upload and store new firmware versions for upgrading multiple devices installed in, or connected to, a Prisma MediaCenter.
Access UMA’s File Management functionality in the Adminstration tab of the iConfig utility of PrismaView.
General Information For more information on using UMA, please refer to the following Help files:
iConfig Help File
PrismaFiberLinX Help File
10 4015100 Rev B
UMA Compatibility Upgrade Process
PrismaGiga-FiberLinX Help File
Media Converter Help File (includes Prisma MediaCenter)
For more information on using the Batch Upgrader, please refer to the following Help file:
Batch Upgrader Help File
4015100 Rev B 11
For Information
For Information
Support Telephone Numbers This table lists the Technical Support and Customer Service numbers for your area.
Region Centers Telephone and Fax Numbers
North America Cisco Services
Atlanta, Georgia United States
For Technical Support, call: Toll-free: 1-800-722-2009 Local: 678-277-1120 (Press 2 at the prompt)
For Customer Service or to request an RMA number, call: Toll-free: 1-800-722-2009 Local: 678-277-1120 (Press 3 at the prompt) Fax: 770-236-5477 E-mail: [email protected]
Europe, Middle East, Africa
Belgium For Technical Support, call: Telephone: 32-56-445-197 or 32-56-445-155 Fax: 32-56-445-061
For Customer Service or to request an RMA number, call: Telephone: 32-56-445-444 Fax: 32-56-445-051 E-mail: [email protected]
Japan Japan Telephone: 81-3-5908-2153 or +81-3-5908-2154 Fax: 81-3-5908-2155 E-mail: [email protected]
Korea Korea Telephone: 82-2-3429-8800 Fax: 82-2-3452-9748 E-mail: [email protected]
China (mainland)
China Telephone: 86-21-2401-4433 Fax: 86-21-2401-4455 E-mail: [email protected]
All other Asia-Pacific countries & Australia
Hong Kong Telephone: 852-2588-4746 Fax: 852-2588-3139 E-mail: [email protected]
Brazil Brazil For Technical Support, call: Telephone: 55-11-3845-9154 ext 230 Fax: 55-11-3845-2514
For Customer Service or to request an RMA number, call: Telephone: 55-11-3845-9154, ext 109 Fax: 55-11-3845-2514 E-mail: [email protected]
12 4015100 Rev B
For Information
Region Centers Telephone and Fax Numbers
Mexico, Central America, Caribbean
Mexico For Technical Support, call: Telephone: 52-3515152599 Fax: 52-3515152599
For Customer Service or to request an RMA number, call: Telephone: 52-55-50-81-8425 Fax: 52-55-52-61-0893 E-mail: [email protected]
All other Latin America countries
Argentina For Technical Support, call: Telephone: 54-23-20-403340 ext 109 Fax: 54-23-20-403340 ext 103
For Customer Service or to request an RMA number, call: Telephone: 770-236-5662 Fax: 770-236-5888 E-mail: [email protected]
5030 Sugarloaf Parkway, Box 465447 Lawrenceville, GA 30044
