Section 2 COMBINATION SILL-THRESHOLDS, the “COMBO SILL”

Standard Sizes: 30”, 32”, 36”, 42”,48”, 60”, 64”, 72” (cut exact).

Other lengths are available.(Extra cost over 73”)Drop In Sills are cut to exact lengthordered.

Center holes are countersunk, 1 perdoor for routed nail-on sill; or,approximately 1 per 12” for drop-in sill.Sills can be ordered without centerholes, if desired.

Special fabrications to easeinstallation with orderinginformation are described onpage 18: Rout for nail-on jambs (3/8” - 1-1/4”) Mullion rout (MR) Rout for metal/mortised frame (RMF) Sill trim notch (SN) Nail-on rabbet

#10 phillips flathead screws areincluded, length per industry standard.

All Combo Sills can be packagedwith any door bottom to create apackaged set.

Sill Covers and Sill Risers are onpage 19.

Special anchors for concrete areavailable at extra cost, see page54.

End Holes are provided with sillsrouted for nail-on jambs.

SILL-THRESHOLD SELECTION GUIDE

COMBO ALUMINUM PRODUCTS, EL CAJON, CATel (619) 447-9200 (800) 457-7500 Fax (619) 442-45589

PROD#

NOTE: Each profile also available for continuous level floor.

WIDTH HEIGHT SLOPE JAMB

520� 5-5/8�� 1-3/8� 5�� 4-3/8 to 5-1/2522� 7-3/4�� 1-3/8� 5�� 6 to 7-1/8

550� 5� � 1-1/8� 9�� 3-5/8 to 4-7/8542� 4-9/16�� 1-1/8� 6�� 4-1/8 to 5650� 5-3/4�� 1-1/8� 9�� 4-3/8 to 5-1/2660� 6-11/16� 1-1/8� 6�� 5-1/2 to 6-1/2675� 6-3/4�� 1-1/8� 9�� 5 to 6-1/4

569� 5-5/8�� 1-1/4� 6�� 4-3/8 to 5-1/2775� 7-3/4�� 1-1/4� 9�� 6 to 7-1/8

580� 5� � 1-3/8� 9�� 3-5/8 to 4-7/8585� 5-1/8�� 1-3/8� 9�� 4 to 4-7/8652� 5-3/4�� 1-3/8� 9�� 4-3/8 to 5-1/2680� 6-13/16� 1-3/8� 9�� 5-1/2 to 6-1/2

542 4 9/16” 11/8” 6° 41/8 to 5550 5” 11/8” 9° 35/8 to 47/8 650 5¾” 11/8” 9° 43/8 to 5½660 6 11/16” 11/8” 6° 5½ to 6½675 6¾” 11/8” 9° 5 to 6¼

569 55/8” 1¼” 6° 43/8 to 5½775 7¾” 1¼” 9° 6 to 71/8

520 55/8” 13/8” 5° 43/8 to 5½522 7¾” 13/8” 5° 6 to 71/8580 5” 13/8” 9° 35/8 to 47/ 8

585 51/8” 13/8” 9° 4 to 47/ 8

652 5¾” 13/8” 9° 43/8 to 5½680 6 13/16” 13/8” 9° 5½ to 6½

SILL-THRESHOLD SELECTION GUIDE

PRODUCT #

NOTE: Each profile also available for continuous level floor.

WIDTH HEIGHT SLOPE JAMB WIDTH

16:

17.

51.

542 4 9/16” 11/8” 6° 41/8 to 5650 5¾” 11/8” 9° 43/8 to 5½

569 55/8” 1¼” 6° 43/8 to 5½775 7¾” 1¼” 9° 6 to 71/8

520 55/8” 13/8” 5° 43/8 to 5½522 7¾” 13/8” 5° 6 to 71/8

585 51/8” 13/8” 9° 4 to 47/ 8

680 6 13/16” 13/8” 9° 5½ to 6½

SILL-THRESHOLD SELECTION GUIDE

PRODUCT #

NOTE: Each profile also available for continuous level floor.

WIDTH HEIGHT SLOPE JAMB WIDTH

14:

15.

34.

continuedCombination Sill-Thresholds

7 3/4

1/2

1 3/8

5 5/8

1/2

1 3/8

522 A

520 A

Indicates location of standard fastener hole.

o 5 slope

o 5 slope

Thermal-Break Threshold for Modular Homes (#520 & #522). Heavy wall thickness for strengthand rigidity. Screw-bosses for attaching to frame (fasteners not included). End Seals available.

THIS DRAWING NOT TO SCALE.

COMBO ALUMINUM PRODUCTS, EL CAJON, CATel (619) 447-9200 (800) 457-7500 Fax (619) 442-4558

PRODUCTS ARE SHOWN ACTUAL SIZE(EXCEPT AS NOTED) 10

continuedCombination Sill-Thresholds

7 3/4

1/2

1 3/8

5 5/8

1/2

1 3/8

522 A

520 A

Indicates location of standard fastener hole.

o 5 slope

o 5 slope

Thermal-Break Threshold for Modular Homes (#520 & #522). Heavy wall thickness for strengthand rigidity. Screw-bosses for attaching to frame (fasteners not included). End Seals available.

THIS DRAWING NOT TO SCALE.

COMBO ALUMINUM PRODUCTS, EL CAJON, CATel (619) 447-9200 (800) 457-7500 Fax (619) 442-4558

PRODUCTS ARE SHOWN ACTUAL SIZE(EXCEPT AS NOTED) 10

continuedCombination Sill-Thresholds

7 3/4

1/2

1 3/8

5 5/8

1/2

1 3/8

522 A

520 A

Indicates location of standard fastener hole.

o 5 slope

o 5 slope

Thermal-Break Threshold for Modular Homes (#520 & #522). Heavy wall thickness for strengthand rigidity. Screw-bosses for attaching to frame (fasteners not included). End Seals available.

THIS DRAWING NOT TO SCALE.

COMBO ALUMINUM PRODUCTS, EL CAJON, CATel (619) 447-9200 (800) 457-7500 Fax (619) 442-4558

PRODUCTS ARE SHOWN ACTUAL SIZE(EXCEPT AS NOTED) 10

THERMAL-BREAK THRESHOLD

continuedCombination Sill-Thresholds

542 A, B

Full length composite insert for glue down or nail-on applications

1 1/ 8

4 9/16

For jambs:4-1/8” to 5” wide.For doors 1-3/4” and over .Will accept extenders834, 836, & 846shown on page 31.

INSERT SILL-THRESHOLDCOMPOSITE & WOOD SUBSTRATE AVAILABLE

Indicates location of standard fastener hole.

775

7

1/41

3/4

A, B

1/41

7 3/4

THIS DRAWING NOT TO SCALE

THIS DRAWING NOT TO SCALE

oFor jambs: 6" to 7-1/8" wide. 9 slope. For doors 1-3/4" and over. 10 X 2" phillips flathead screws included.

oFor jambs: 6" to 7-1/8" wide. 9 slope. For doors 1-3/4" and over. 10 X 2" phillips flathead screws included.

o6 slope

COMBO ALUMINUM PRODUCTS, EL CAJON, CATel (619) 447-9200 (800) 457-7500 Fax (619) 442-4558

PRODUCTS ARE SHOWN ACTUAL SIZE(EXCEPT AS NOTED)17

776 A, B

continuedCombination Sill-Thresholds

7 3/4

1/2

1 3/8

5 5/8

1/2

1 3/8

522 A

520 A

Indicates location of standard fastener hole.

o 5 slope

o 5 slope

Thermal-Break Threshold for Modular Homes (#520 & #522). Heavy wall thickness for strengthand rigidity. Screw-bosses for attaching to frame (fasteners not included). End Seals available.

THIS DRAWING NOT TO SCALE.

COMBO ALUMINUM PRODUCTS, EL CAJON, CATel (619) 447-9200 (800) 457-7500 Fax (619) 442-4558

PRODUCTS ARE SHOWN ACTUAL SIZE(EXCEPT AS NOTED) 10

continuedCombination Sill-Thresholds

7 3/4

1/2

1 3/8

5 5/8

1/2

1 3/8

522 A

520 A

Indicates location of standard fastener hole.

o 5 slope

o 5 slope

Thermal-Break Threshold for Modular Homes (#520 & #522). Heavy wall thickness for strengthand rigidity. Screw-bosses for attaching to frame (fasteners not included). End Seals available.

THIS DRAWING NOT TO SCALE.

COMBO ALUMINUM PRODUCTS, EL CAJON, CATel (619) 447-9200 (800) 457-7500 Fax (619) 442-4558

PRODUCTS ARE SHOWN ACTUAL SIZE(EXCEPT AS NOTED) 10

continuedCombination Sill-Thresholds

7 3/4

1/2

1 3/8

5 5/8

1/2

1 3/8

522 A

520 A

Indicates location of standard fastener hole.

o 5 slope

o 5 slope

Thermal-Break Threshold for Modular Homes (#520 & #522). Heavy wall thickness for strengthand rigidity. Screw-bosses for attaching to frame (fasteners not included). End Seals available.

THIS DRAWING NOT TO SCALE.

COMBO ALUMINUM PRODUCTS, EL CAJON, CATel (619) 447-9200 (800) 457-7500 Fax (619) 442-4558

PRODUCTS ARE SHOWN ACTUAL SIZE(EXCEPT AS NOTED) 10

THERMAL-BREAK THRESHOLD

continuedCombination Sill-Thresholds

542 A, B

Full length composite insert for glue down or nail-on applications

1 1/ 8

4 9/16

For jambs:4-1/8” to 5” wide.For doors 1-3/4” and over .Will accept extenders834, 836, & 846shown on page 31.

INSERT SILL-THRESHOLDCOMPOSITE & WOOD SUBSTRATE AVAILABLE

Indicates location of standard fastener hole.

775

7

1/41

3/4

A, B

1/41

7 3/4

THIS DRAWING NOT TO SCALE

THIS DRAWING NOT TO SCALE

oFor jambs: 6" to 7-1/8" wide. 9 slope. For doors 1-3/4" and over. 10 X 2" phillips flathead screws included.

oFor jambs: 6" to 7-1/8" wide. 9 slope. For doors 1-3/4" and over. 10 X 2" phillips flathead screws included.

o6 slope

COMBO ALUMINUM PRODUCTS, EL CAJON, CATel (619) 447-9200 (800) 457-7500 Fax (619) 442-4558

PRODUCTS ARE SHOWN ACTUAL SIZE(EXCEPT AS NOTED)17

776 A, B

THERMAL-BREAK THRESHOLD

27.

Full length wood or composite insert for glue down or nail-on applications

834 and 836

5

1/81

551

For jambs:3-5/8” to 4-7/8” wide &continuous level floor.10 x 2" phillipsflathead screwsare included.

A, B, CH, PG, W

550

For jambs:3-5/8” to 4-7/8” wide.10 x 2” phillipsflathead screwsare included.

A, B, CH, PG, W1

5

The Original Combo-Sill

continuedCombination Sill-Thresholds

1/8

Indicates location of standard fastener hole.

o 9 slope

o 9 slope

COMBO ALUMINUM PRODUCTS, EL CAJON, CATel (619) 447-9200 (800) 457-7500 Fax (619) 442-4558PRODUCTS ARE SHOWN ACTUAL SIZE11

5

1/81

551

For jambs:3-5/8” to 4-7/8” wide &continuous level floor.10 x 2" phillipsflathead screwsare included.

A, B, CH, PG, W

550

For jambs:3-5/8” to 4-7/8” wide.10 x 2” phillipsflathead screwsare included.

A, B, CH, PG, W1

5

The Original Combo-Sill

continuedCombination Sill-Thresholds

1/8

Indicates location of standard fastener hole.

o 9 slope

o 9 slope

COMBO ALUMINUM PRODUCTS, EL CAJON, CATel (619) 447-9200 (800) 457-7500 Fax (619) 442-4558PRODUCTS ARE SHOWN ACTUAL SIZE11

5

1/81

551

For jambs:3-5/8” to 4-7/8” wide &continuous level floor.10 x 2" phillipsflathead screwsare included.

A, B, CH, PG, W

550

For jambs:3-5/8” to 4-7/8” wide.10 x 2” phillipsflathead screwsare included.

A, B, CH, PG, W1

5

The Original Combo-Sill

continuedCombination Sill-Thresholds

1/8

Indicates location of standard fastener hole.

o 9 slope

o 9 slope

COMBO ALUMINUM PRODUCTS, EL CAJON, CATel (619) 447-9200 (800) 457-7500 Fax (619) 442-4558PRODUCTS ARE SHOWN ACTUAL SIZE11

continuedCombination Sill-Thresholds

6 11/16

1 3/8

1 3/8

4 11/16

564 A

For jambs:4-1/8” to 5” wide.

566 A

For jambs:5-1/2” to 6-1/2” wide.

Indicates location of standard fastener hole.

o 5 slope

o 5 slope

COMBO ALUMINUM PRODUCTS, EL CAJON, CATel (619) 447-9200 (800) 457-7500 Fax (619) 442-4558 PRODUCTS ARE SHOWN ACTUAL SIZE 12

“COMBO SILLS”

5

1/81

551

For jambs:3-5/8” to 4-7/8” wide &continuous level floor.10 x 2" phillipsflathead screwsare included.

A, B, CH, PG, W

550

For jambs:3-5/8” to 4-7/8” wide.10 x 2” phillipsflathead screwsare included.

A, B, CH, PG, W1

5

The Original Combo-Sill

continuedCombination Sill-Thresholds

1/8

Indicates location of standard fastener hole.

o 9 slope

o 9 slope

COMBO ALUMINUM PRODUCTS, EL CAJON, CATel (619) 447-9200 (800) 457-7500 Fax (619) 442-4558PRODUCTS ARE SHOWN ACTUAL SIZE11

5

1/81

551

For jambs:3-5/8” to 4-7/8” wide &continuous level floor.10 x 2" phillipsflathead screwsare included.

A, B, CH, PG, W

550

For jambs:3-5/8” to 4-7/8” wide.10 x 2” phillipsflathead screwsare included.

A, B, CH, PG, W1

5

The Original Combo-Sill

continuedCombination Sill-Thresholds

1/8

Indicates location of standard fastener hole.

o 9 slope

o 9 slope

COMBO ALUMINUM PRODUCTS, EL CAJON, CATel (619) 447-9200 (800) 457-7500 Fax (619) 442-4558PRODUCTS ARE SHOWN ACTUAL SIZE11

5

1/81

551

For jambs:3-5/8” to 4-7/8” wide &continuous level floor.10 x 2" phillipsflathead screwsare included.

A, B, CH, PG, W

550

For jambs:3-5/8” to 4-7/8” wide.10 x 2” phillipsflathead screwsare included.

A, B, CH, PG, W1

5

The Original Combo-Sill

continuedCombination Sill-Thresholds

1/8

Indicates location of standard fastener hole.

o 9 slope

o 9 slope

COMBO ALUMINUM PRODUCTS, EL CAJON, CATel (619) 447-9200 (800) 457-7500 Fax (619) 442-4558PRODUCTS ARE SHOWN ACTUAL SIZE11

continuedCombination Sill-Thresholds

6 11/16

1 3/8

1 3/8

4 11/16

564 A

For jambs:4-1/8” to 5” wide.

566 A

For jambs:5-1/2” to 6-1/2” wide.

Indicates location of standard fastener hole.

o 5 slope

o 5 slope

COMBO ALUMINUM PRODUCTS, EL CAJON, CATel (619) 447-9200 (800) 457-7500 Fax (619) 442-4558 PRODUCTS ARE SHOWN ACTUAL SIZE 12

“COMBO SILLS”

5

1/81

551

For jambs:3-5/8” to 4-7/8” wide &continuous level floor.10 x 2" phillipsflathead screwsare included.

A, B, CH, PG, W

550

For jambs:3-5/8” to 4-7/8” wide.10 x 2” phillipsflathead screwsare included.

A, B, CH, PG, W1

5

The Original Combo-Sill

continuedCombination Sill-Thresholds

1/8

Indicates location of standard fastener hole.

o 9 slope

o 9 slope

COMBO ALUMINUM PRODUCTS, EL CAJON, CATel (619) 447-9200 (800) 457-7500 Fax (619) 442-4558PRODUCTS ARE SHOWN ACTUAL SIZE11

5

1/81

551

For jambs:3-5/8” to 4-7/8” wide &continuous level floor.10 x 2" phillipsflathead screwsare included.

A, B, CH, PG, W

550

For jambs:3-5/8” to 4-7/8” wide.10 x 2” phillipsflathead screwsare included.

A, B, CH, PG, W1

5

The Original Combo-Sill

continuedCombination Sill-Thresholds

1/8

Indicates location of standard fastener hole.

o 9 slope

o 9 slope

COMBO ALUMINUM PRODUCTS, EL CAJON, CATel (619) 447-9200 (800) 457-7500 Fax (619) 442-4558PRODUCTS ARE SHOWN ACTUAL SIZE11

5

1/81

551

For jambs:3-5/8” to 4-7/8” wide &continuous level floor.10 x 2" phillipsflathead screwsare included.

A, B, CH, PG, W

550

For jambs:3-5/8” to 4-7/8” wide.10 x 2” phillipsflathead screwsare included.

A, B, CH, PG, W1

5

The Original Combo-Sill

continuedCombination Sill-Thresholds

1/8

Indicates location of standard fastener hole.

o 9 slope

o 9 slope

COMBO ALUMINUM PRODUCTS, EL CAJON, CATel (619) 447-9200 (800) 457-7500 Fax (619) 442-4558PRODUCTS ARE SHOWN ACTUAL SIZE11

continuedCombination Sill-Thresholds

6 11/16

1 3/8

1 3/8

4 11/16

564 A

For jambs:4-1/8” to 5” wide.

566 A

For jambs:5-1/2” to 6-1/2” wide.

Indicates location of standard fastener hole.

o 5 slope

o 5 slope

COMBO ALUMINUM PRODUCTS, EL CAJON, CATel (619) 447-9200 (800) 457-7500 Fax (619) 442-4558 PRODUCTS ARE SHOWN ACTUAL SIZE 12

“COMBO SILLS”

continuedCombination Sill-Thresholds

6 11/16

1 3/8

1 3/8

4 11/16

564 A

For jambs:4-1/8” to 5” wide.

566 A

For jambs:5-1/2” to 6-1/2” wide.

Indicates location of standard fastener hole.

o 5 slope

o 5 slope

COMBO ALUMINUM PRODUCTS, EL CAJON, CATel (619) 447-9200 (800) 457-7500 Fax (619) 442-4558 PRODUCTS ARE SHOWN ACTUAL SIZE 12

continuedCombination Sill-Thresholds

For jambs:3-5/8” to 4-7/8” wide &continuous level floor.10 x 2-1/2” phillipsflathead screwsare included.

5

3/81

580For jambs:3-5/8” to 4-7/8” wide.10 x 2-1/2” phillipsflathead screwsare included.

A, B

581 A, B

1 3 /8

5

1 1/4

5 5/ 8

569 B

For jambs:4-3/8” to 5-1/2” wide.

Indicates location of standard fastener hole.

o 9 slope

o 9 slope

o 6 slope

COMBO ALUMINUM PRODUCTS, EL CAJON, CATel (619) 447-9200 (800) 457-7500 Fax (619) 442-4558PRODUCTS ARE SHOWN ACTUAL SIZE13

“COMBO SILLS”

continuedCombination Sill-Thresholds

For jambs:3-5/8” to 4-7/8” wide &continuous level floor.10 x 2-1/2” phillipsflathead screwsare included.

5

3/81

580For jambs:3-5/8” to 4-7/8” wide.10 x 2-1/2” phillipsflathead screwsare included.

A, B

581 A, B

1 3 /8

5

1 1/4

5 5/ 8

569 B

For jambs:4-3/8” to 5-1/2” wide.

Indicates location of standard fastener hole.

o 9 slope

o 9 slope

o 6 slope

COMBO ALUMINUM PRODUCTS, EL CAJON, CATel (619) 447-9200 (800) 457-7500 Fax (619) 442-4558PRODUCTS ARE SHOWN ACTUAL SIZE13

Combination Sill-Thresholds

For jambs:4-3/8” to 5-1/2”wide. 10 X 2”phillips flatheadscrews areincluded.

5

1/81

3/4

5 3/4

continued

1/81For jambs:4-3/8” to 5-1/2” wide& continuous levelfloor. 10 X 2”phillips flatheadscrews are included.

585 A, B

3/81

1/85

For jambs:4” to 4-7/8” wide;For doors 1-3/4” andover. 10 x 2-1/2” phillipsflathead screwsare included.

586 A, B

650 A, B

651 A, B

3/81

1/85

For jambs:4” to 4-7/8” wide &continuous level floor.For doors 1-3/4” andover. 10 x 2-1/2” phillipsflathead screwsare included.

Indicates location of standard fastener hole.

o 9 slope

o 9 slope

o 9 slope

o 9 slope

COMBO ALUMINUM PRODUCTS, EL CAJON, CATel (619) 447-9200 (800) 457-7500 Fax (619) 442-4558 PRODUCTS ARE SHOWN ACTUAL SIZE 14

5

1/81

551

For jambs:3-5/8” to 4-7/8” wide &continuous level floor.10 x 2" phillipsflathead screwsare included.

A, B, CH, PG, W

550

For jambs:3-5/8” to 4-7/8” wide.10 x 2” phillipsflathead screwsare included.

A, B, CH, PG, W1

5

The Original Combo-Sill

continuedCombination Sill-Thresholds

1/8

Indicates location of standard fastener hole.

o 9 slope

o 9 slope

COMBO ALUMINUM PRODUCTS, EL CAJON, CATel (619) 447-9200 (800) 457-7500 Fax (619) 442-4558PRODUCTS ARE SHOWN ACTUAL SIZE11

5

1/81

551

For jambs:3-5/8” to 4-7/8” wide &continuous level floor.10 x 2" phillipsflathead screwsare included.

A, B, CH, PG, W

550

For jambs:3-5/8” to 4-7/8” wide.10 x 2” phillipsflathead screwsare included.

A, B, CH, PG, W1

5

The Original Combo-Sill

continuedCombination Sill-Thresholds

1/8

Indicates location of standard fastener hole.

o 9 slope

o 9 slope

COMBO ALUMINUM PRODUCTS, EL CAJON, CATel (619) 447-9200 (800) 457-7500 Fax (619) 442-4558PRODUCTS ARE SHOWN ACTUAL SIZE11

5

1/81

551

For jambs:3-5/8” to 4-7/8” wide &continuous level floor.10 x 2" phillipsflathead screwsare included.

A, B, CH, PG, W

550

For jambs:3-5/8” to 4-7/8” wide.10 x 2” phillipsflathead screwsare included.

A, B, CH, PG, W1

5

The Original Combo-Sill

continuedCombination Sill-Thresholds

1/8

Indicates location of standard fastener hole.

o 9 slope

o 9 slope

COMBO ALUMINUM PRODUCTS, EL CAJON, CATel (619) 447-9200 (800) 457-7500 Fax (619) 442-4558PRODUCTS ARE SHOWN ACTUAL SIZE11

continuedCombination Sill-Thresholds

6 11/16

1 3/8

1 3/8

4 11/16

564 A

For jambs:4-1/8” to 5” wide.

566 A

For jambs:5-1/2” to 6-1/2” wide.

Indicates location of standard fastener hole.

o 5 slope

o 5 slope

COMBO ALUMINUM PRODUCTS, EL CAJON, CATel (619) 447-9200 (800) 457-7500 Fax (619) 442-4558 PRODUCTS ARE SHOWN ACTUAL SIZE 12

“COMBO SILLS”

continuedCombination Sill-Thresholds

6 11/16

1 3/8

1 3/8

4 11/16

564 A

For jambs:4-1/8” to 5” wide.

566 A

For jambs:5-1/2” to 6-1/2” wide.

Indicates location of standard fastener hole.

o 5 slope

o 5 slope

COMBO ALUMINUM PRODUCTS, EL CAJON, CATel (619) 447-9200 (800) 457-7500 Fax (619) 442-4558 PRODUCTS ARE SHOWN ACTUAL SIZE 12

continuedCombination Sill-Thresholds

For jambs:3-5/8” to 4-7/8” wide &continuous level floor.10 x 2-1/2” phillipsflathead screwsare included.

5

3/81

580For jambs:3-5/8” to 4-7/8” wide.10 x 2-1/2” phillipsflathead screwsare included.

A, B

581 A, B

1 3 /8

5

1 1/4

5 5/ 8

569 B

For jambs:4-3/8” to 5-1/2” wide.

Indicates location of standard fastener hole.

o 9 slope

o 9 slope

o 6 slope

COMBO ALUMINUM PRODUCTS, EL CAJON, CATel (619) 447-9200 (800) 457-7500 Fax (619) 442-4558PRODUCTS ARE SHOWN ACTUAL SIZE13

continuedCombination Sill-Thresholds

For jambs:3-5/8” to 4-7/8” wide &continuous level floor.10 x 2-1/2” phillipsflathead screwsare included.

5

3/81

580For jambs:3-5/8” to 4-7/8” wide.10 x 2-1/2” phillipsflathead screwsare included.

A, B

581 A, B

1 3 /8

5

1 1/4

5 5/ 8

569 B

For jambs:4-3/8” to 5-1/2” wide.

Indicates location of standard fastener hole.

o 9 slope

o 9 slope

o 6 slope

COMBO ALUMINUM PRODUCTS, EL CAJON, CATel (619) 447-9200 (800) 457-7500 Fax (619) 442-4558PRODUCTS ARE SHOWN ACTUAL SIZE13

Combination Sill-Thresholds

For jambs:4-3/8” to 5-1/2”wide. 10 X 2”phillips flatheadscrews areincluded.

5

1/81

3/4

5 3/4

continued

1/81For jambs:4-3/8” to 5-1/2” wide& continuous levelfloor. 10 X 2”phillips flatheadscrews are included.

585 A, B

3/81

1/85

For jambs:4” to 4-7/8” wide;For doors 1-3/4” andover. 10 x 2-1/2” phillipsflathead screwsare included.

586 A, B

650 A, B

651 A, B

3/81

1/85

For jambs:4” to 4-7/8” wide &continuous level floor.For doors 1-3/4” andover. 10 x 2-1/2” phillipsflathead screwsare included.

Indicates location of standard fastener hole.

o 9 slope

o 9 slope

o 9 slope

o 9 slope

COMBO ALUMINUM PRODUCTS, EL CAJON, CATel (619) 447-9200 (800) 457-7500 Fax (619) 442-4558 PRODUCTS ARE SHOWN ACTUAL SIZE 14

For jambs: 5 1/2" to 6-1/2" wide. 6 slope.For doors 1-3/4" and over. 10 X 2" phillipsflathead screws are included.

continuedCombination Sill-Thresholds

For jambs:4-3/8” to 5-1/2” wide.10 X 2-1/2” phillipsflathead screws areincluded.

652 A, B

1 3 /8

1 3 /8

5 3/4

For jambs:4-3/8” to 5-1/2” wide& continuous levelfloor. 10 X 2-1/2”phillips flatheadscrews are included.

653 A, B

660 A, B

5 3/4

6

1/81

11/16

o

For jambs: 5 1/2" to 6-1/2" wide. 6 slope.For doors 1-3/4" and over. 10 X 2" phillipsflathead screws are included.

o

6

1/81

11/16

Indicates location of standard fastener hole.

o 9 slope

o 9 slope

COMBO ALUMINUM PRODUCTS, EL CAJON, CATel (619) 447-9200 (800) 457-7500 Fax (619) 442-4558PRODUCTS ARE SHOWN ACTUAL SIZE15

661 A, B

continuedCombination Sill-Thresholds

6

1/81

3/4

675 A, B

o

6

1/81

3/4

6

3/81

13 /16

Indicates location of standard fastener hole.

For jambs: 5" to 6-1/4" wide. 9 slope.10 X 2" phillips flathead screws areincluded.

oFor jambs: 5" to 6-1/4" wide & continuouslevel floor. 9 slope. 10 X 2" phillipsflathead screws are included.

oFor jambs: 5-1/2" to 6-1/2" wide. 9 slope.For doors 1-3/4" and over. 10 X 2-1/2" phillipsflathead screws are included.

oFor jambs: 5-1/2" to 6-1/2" wide & continuouslevel floor. 9 slope. For doors 1-3/4" and over.10 X 2-1/2" phillips flathead screws are included.

6

3/81

13 /16

COMBO ALUMINUM PRODUCTS, EL CAJON, CATel (619) 447-9200 (800) 457-7500 Fax (619) 442-4558 PRODUCTS ARE SHOWN ACTUAL SIZE 16

676 A, B

680 A, B

681 A, B

continuedCombination Sill-Thresholds

542 A, B

Full length composite insert for glue down or nail-on applications

1 1/ 8

4 9/16

For jambs:4-1/8” to 5” wide.For doors 1-3/4” and over .Will accept extenders834, 836, & 846shown on page 31.

INSERT SILL-THRESHOLDCOMPOSITE & WOOD SUBSTRATE AVAILABLE

Indicates location of standard fastener hole.

775

7

1/41

3/4

A, B

1/41

7 3/4

THIS DRAWING NOT TO SCALE

THIS DRAWING NOT TO SCALE

oFor jambs: 6" to 7-1/8" wide. 9 slope. For doors 1-3/4" and over. 10 X 2" phillips flathead screws included.

oFor jambs: 6" to 7-1/8" wide. 9 slope. For doors 1-3/4" and over. 10 X 2" phillips flathead screws included.

o6 slope

COMBO ALUMINUM PRODUCTS, EL CAJON, CATel (619) 447-9200 (800) 457-7500 Fax (619) 442-4558

PRODUCTS ARE SHOWN ACTUAL SIZE(EXCEPT AS NOTED)17

776 A, B

continuedCombination Sill-Thresholds

542 A, B

Full length composite insert for glue down or nail-on applications

1 1/ 8

4 9/16

For jambs:4-1/8” to 5” wide.For doors 1-3/4” and over .Will accept extenders834, 836, & 846shown on page 31.

INSERT SILL-THRESHOLDCOMPOSITE & WOOD SUBSTRATE AVAILABLE

Indicates location of standard fastener hole.

775

7

1/41

3/4

A, B

1/41

7 3/4

THIS DRAWING NOT TO SCALE

THIS DRAWING NOT TO SCALE

oFor jambs: 6" to 7-1/8" wide. 9 slope. For doors 1-3/4" and over. 10 X 2" phillips flathead screws included.

oFor jambs: 6" to 7-1/8" wide. 9 slope. For doors 1-3/4" and over. 10 X 2" phillips flathead screws included.

o6 slope

COMBO ALUMINUM PRODUCTS, EL CAJON, CATel (619) 447-9200 (800) 457-7500 Fax (619) 442-4558

PRODUCTS ARE SHOWN ACTUAL SIZE(EXCEPT AS NOTED)17

776 A, B

Forjambs:6”to71/ 8”wideandcontinuouslevelfloor.9°slope.Fordoors1¾”andover.10x2”phillipsflatheadscrewsareincluded.

Forjambs:6”to71/ 8”wideandcontinuouslevelfloor.9°slope.Fordoors1¾”andover.10x2”phillipsflatheadscrewsareincluded.

continuedCombination Sill-Thresholds

For jambs:3-5/8” to 4-7/8” wide &continuous level floor.10 x 2-1/2” phillipsflathead screwsare included.

5

3/81

580For jambs:3-5/8” to 4-7/8” wide.10 x 2-1/2” phillipsflathead screwsare included.

A, B

581 A, B

1 3 /8

5

1 1/4

5 5/ 8

569 B

For jambs:4-3/8” to 5-1/2” wide.

Indicates location of standard fastener hole.

o 9 slope

o 9 slope

o 6 slope

COMBO ALUMINUM PRODUCTS, EL CAJON, CATel (619) 447-9200 (800) 457-7500 Fax (619) 442-4558PRODUCTS ARE SHOWN ACTUAL SIZE13

Combination Sill-Thresholds

For jambs:4-3/8” to 5-1/2”wide. 10 X 2”phillips flatheadscrews areincluded.

5

1/81

3/4

5 3/4

continued

1/81For jambs:4-3/8” to 5-1/2” wide& continuous levelfloor. 10 X 2”phillips flatheadscrews are included.

585 A, B

3/81

1/85

For jambs:4” to 4-7/8” wide;For doors 1-3/4” andover. 10 x 2-1/2” phillipsflathead screwsare included.

586 A, B

650 A, B

651 A, B

3/81

1/85

For jambs:4” to 4-7/8” wide &continuous level floor.For doors 1-3/4” andover. 10 x 2-1/2” phillipsflathead screwsare included.

Indicates location of standard fastener hole.

o 9 slope

o 9 slope

o 9 slope

o 9 slope

COMBO ALUMINUM PRODUCTS, EL CAJON, CATel (619) 447-9200 (800) 457-7500 Fax (619) 442-4558 PRODUCTS ARE SHOWN ACTUAL SIZE 14

For jambs: 5 1/2" to 6-1/2" wide. 6 slope.For doors 1-3/4" and over. 10 X 2" phillipsflathead screws are included.

continuedCombination Sill-Thresholds

For jambs:4-3/8” to 5-1/2” wide.10 X 2-1/2” phillipsflathead screws areincluded.

652 A, B

1 3 /8

1 3 /8

5 3/4

For jambs:4-3/8” to 5-1/2” wide& continuous levelfloor. 10 X 2-1/2”phillips flatheadscrews are included.

653 A, B

660 A, B

5 3/4

6

1/81

11/16

o

For jambs: 5 1/2" to 6-1/2" wide. 6 slope.For doors 1-3/4" and over. 10 X 2" phillipsflathead screws are included.

o

6

1/81

11/16

Indicates location of standard fastener hole.

o 9 slope

o 9 slope

COMBO ALUMINUM PRODUCTS, EL CAJON, CATel (619) 447-9200 (800) 457-7500 Fax (619) 442-4558PRODUCTS ARE SHOWN ACTUAL SIZE15

661 A, B

continuedCombination Sill-Thresholds

6

1/81

3/4

675 A, B

o

6

1/81

3/4

6

3/81

13 /16

Indicates location of standard fastener hole.

For jambs: 5" to 6-1/4" wide. 9 slope.10 X 2" phillips flathead screws areincluded.

oFor jambs: 5" to 6-1/4" wide & continuouslevel floor. 9 slope. 10 X 2" phillipsflathead screws are included.

oFor jambs: 5-1/2" to 6-1/2" wide. 9 slope.For doors 1-3/4" and over. 10 X 2-1/2" phillipsflathead screws are included.

oFor jambs: 5-1/2" to 6-1/2" wide & continuouslevel floor. 9 slope. For doors 1-3/4" and over.10 X 2-1/2" phillips flathead screws are included.

6

3/81

13 /16

COMBO ALUMINUM PRODUCTS, EL CAJON, CATel (619) 447-9200 (800) 457-7500 Fax (619) 442-4558 PRODUCTS ARE SHOWN ACTUAL SIZE 16

676 A, B

680 A, B

681 A, B

continuedCombination Sill-Thresholds

542 A, B

Full length composite insert for glue down or nail-on applications

1 1/ 8

4 9/16

For jambs:4-1/8” to 5” wide.For doors 1-3/4” and over .Will accept extenders834, 836, & 846shown on page 31.

INSERT SILL-THRESHOLDCOMPOSITE & WOOD SUBSTRATE AVAILABLE

Indicates location of standard fastener hole.

775

7

1/41

3/4

A, B

1/41

7 3/4

THIS DRAWING NOT TO SCALE

THIS DRAWING NOT TO SCALE

oFor jambs: 6" to 7-1/8" wide. 9 slope. For doors 1-3/4" and over. 10 X 2" phillips flathead screws included.

oFor jambs: 6" to 7-1/8" wide. 9 slope. For doors 1-3/4" and over. 10 X 2" phillips flathead screws included.

o6 slope

COMBO ALUMINUM PRODUCTS, EL CAJON, CATel (619) 447-9200 (800) 457-7500 Fax (619) 442-4558

PRODUCTS ARE SHOWN ACTUAL SIZE(EXCEPT AS NOTED)17

776 A, B

continuedCombination Sill-Thresholds

542 A, B

Full length composite insert for glue down or nail-on applications

1 1/ 8

4 9/16

For jambs:4-1/8” to 5” wide.For doors 1-3/4” and over .Will accept extenders834, 836, & 846shown on page 31.

INSERT SILL-THRESHOLDCOMPOSITE & WOOD SUBSTRATE AVAILABLE

Indicates location of standard fastener hole.

775

7

1/41

3/4

A, B

1/41

7 3/4

THIS DRAWING NOT TO SCALE

THIS DRAWING NOT TO SCALE

oFor jambs: 6" to 7-1/8" wide. 9 slope. For doors 1-3/4" and over. 10 X 2" phillips flathead screws included.

oFor jambs: 6" to 7-1/8" wide. 9 slope. For doors 1-3/4" and over. 10 X 2" phillips flathead screws included.

o6 slope

COMBO ALUMINUM PRODUCTS, EL CAJON, CATel (619) 447-9200 (800) 457-7500 Fax (619) 442-4558

PRODUCTS ARE SHOWN ACTUAL SIZE(EXCEPT AS NOTED)17

776 A, B

Forjambs:6”to71/ 8”wideandcontinuouslevelfloor.9°slope.Fordoors1¾”andover.10x2”phillipsflatheadscrewsareincluded.

Forjambs:6”to71/ 8”wideandcontinuouslevelfloor.9°slope.Fordoors1¾”andover.10x2”phillipsflatheadscrewsareincluded.

For jambs: 5 1/2" to 6-1/2" wide. 6 slope.For doors 1-3/4" and over. 10 X 2" phillipsflathead screws are included.

continuedCombination Sill-Thresholds

For jambs:4-3/8” to 5-1/2” wide.10 X 2-1/2” phillipsflathead screws areincluded.

652 A, B

1 3 /8

1 3 /8

5 3/4

For jambs:4-3/8” to 5-1/2” wide& continuous levelfloor. 10 X 2-1/2”phillips flatheadscrews are included.

653 A, B

660 A, B

5 3/4

6

1/81

11/16

o

For jambs: 5 1/2" to 6-1/2" wide. 6 slope.For doors 1-3/4" and over. 10 X 2" phillipsflathead screws are included.

o

6

1/81

11/16

Indicates location of standard fastener hole.

o 9 slope

o 9 slope

COMBO ALUMINUM PRODUCTS, EL CAJON, CATel (619) 447-9200 (800) 457-7500 Fax (619) 442-4558PRODUCTS ARE SHOWN ACTUAL SIZE15

661 A, B

continuedCombination Sill-Thresholds

6

1/81

3/4

675 A, B

o

6

1/81

3/4

6

3/81

13 /16

Indicates location of standard fastener hole.

For jambs: 5" to 6-1/4" wide. 9 slope.10 X 2" phillips flathead screws areincluded.

oFor jambs: 5" to 6-1/4" wide & continuouslevel floor. 9 slope. 10 X 2" phillipsflathead screws are included.

oFor jambs: 5-1/2" to 6-1/2" wide. 9 slope.For doors 1-3/4" and over. 10 X 2-1/2" phillipsflathead screws are included.

oFor jambs: 5-1/2" to 6-1/2" wide & continuouslevel floor. 9 slope. For doors 1-3/4" and over.10 X 2-1/2" phillips flathead screws are included.

6

3/81

13 /16

COMBO ALUMINUM PRODUCTS, EL CAJON, CATel (619) 447-9200 (800) 457-7500 Fax (619) 442-4558 PRODUCTS ARE SHOWN ACTUAL SIZE 16

676 A, B

680 A, B

681 A, B

continuedCombination Sill-Thresholds

542 A, B

Full length composite insert for glue down or nail-on applications

1 1/ 8

4 9/16

For jambs:4-1/8” to 5” wide.For doors 1-3/4” and over .Will accept extenders834, 836, & 846shown on page 31.

INSERT SILL-THRESHOLDCOMPOSITE & WOOD SUBSTRATE AVAILABLE

Indicates location of standard fastener hole.

775

7

1/41

3/4

A, B

1/41

7 3/4

THIS DRAWING NOT TO SCALE

THIS DRAWING NOT TO SCALE

oFor jambs: 6" to 7-1/8" wide. 9 slope. For doors 1-3/4" and over. 10 X 2" phillips flathead screws included.

oFor jambs: 6" to 7-1/8" wide. 9 slope. For doors 1-3/4" and over. 10 X 2" phillips flathead screws included.

o6 slope

COMBO ALUMINUM PRODUCTS, EL CAJON, CATel (619) 447-9200 (800) 457-7500 Fax (619) 442-4558

PRODUCTS ARE SHOWN ACTUAL SIZE(EXCEPT AS NOTED)17

776 A, B

continuedCombination Sill-Thresholds

542 A, B

Full length composite insert for glue down or nail-on applications

1 1/ 8

4 9/16

For jambs:4-1/8” to 5” wide.For doors 1-3/4” and over .Will accept extenders834, 836, & 846shown on page 31.

INSERT SILL-THRESHOLDCOMPOSITE & WOOD SUBSTRATE AVAILABLE

Indicates location of standard fastener hole.

775

7

1/41

3/4

A, B

1/41

7 3/4

THIS DRAWING NOT TO SCALE

THIS DRAWING NOT TO SCALE

oFor jambs: 6" to 7-1/8" wide. 9 slope. For doors 1-3/4" and over. 10 X 2" phillips flathead screws included.

oFor jambs: 6" to 7-1/8" wide. 9 slope. For doors 1-3/4" and over. 10 X 2" phillips flathead screws included.

o6 slope

COMBO ALUMINUM PRODUCTS, EL CAJON, CATel (619) 447-9200 (800) 457-7500 Fax (619) 442-4558

PRODUCTS ARE SHOWN ACTUAL SIZE(EXCEPT AS NOTED)17

776 A, B

Forjambs:6”to71/ 8”wideandcontinuouslevelfloor.9°slope.Fordoors1¾”andover.10x2”phillipsflatheadscrewsareincluded.

Forjambs:6”to71/ 8”wideandcontinuouslevelfloor.9°slope.Fordoors1¾”andover.10x2”phillipsflatheadscrewsareincluded.

For jambs: 5 1/2" to 6-1/2" wide. 6 slope.For doors 1-3/4" and over. 10 X 2" phillipsflathead screws are included.

continuedCombination Sill-Thresholds

For jambs:4-3/8” to 5-1/2” wide.10 X 2-1/2” phillipsflathead screws areincluded.

652 A, B

1 3 /8

1 3 /8

5 3/4

For jambs:4-3/8” to 5-1/2” wide& continuous levelfloor. 10 X 2-1/2”phillips flatheadscrews are included.

653 A, B

660 A, B

5 3/4

6

1/81

11/16

o

For jambs: 5 1/2" to 6-1/2" wide. 6 slope.For doors 1-3/4" and over. 10 X 2" phillipsflathead screws are included.

o

6

1/81

11/16

Indicates location of standard fastener hole.

o 9 slope

o 9 slope

COMBO ALUMINUM PRODUCTS, EL CAJON, CATel (619) 447-9200 (800) 457-7500 Fax (619) 442-4558PRODUCTS ARE SHOWN ACTUAL SIZE15

661 A, B

continuedCombination Sill-Thresholds

6

1/81

3/4

675 A, B

o

6

1/81

3/4

6

3/81

13 /16

Indicates location of standard fastener hole.

For jambs: 5" to 6-1/4" wide. 9 slope.10 X 2" phillips flathead screws areincluded.

oFor jambs: 5" to 6-1/4" wide & continuouslevel floor. 9 slope. 10 X 2" phillipsflathead screws are included.

oFor jambs: 5-1/2" to 6-1/2" wide. 9 slope.For doors 1-3/4" and over. 10 X 2-1/2" phillipsflathead screws are included.

oFor jambs: 5-1/2" to 6-1/2" wide & continuouslevel floor. 9 slope. For doors 1-3/4" and over.10 X 2-1/2" phillips flathead screws are included.

6

3/81

13 /16

COMBO ALUMINUM PRODUCTS, EL CAJON, CATel (619) 447-9200 (800) 457-7500 Fax (619) 442-4558 PRODUCTS ARE SHOWN ACTUAL SIZE 16

676 A, B

680 A, B

681 A, B

continuedCombination Sill-Thresholds

542 A, B

Full length composite insert for glue down or nail-on applications

1 1/ 8

4 9/16

For jambs:4-1/8” to 5” wide.For doors 1-3/4” and over .Will accept extenders834, 836, & 846shown on page 31.

INSERT SILL-THRESHOLDCOMPOSITE & WOOD SUBSTRATE AVAILABLE

Indicates location of standard fastener hole.

775

7

1/41

3/4

A, B

1/41

7 3/4

THIS DRAWING NOT TO SCALE

THIS DRAWING NOT TO SCALE

oFor jambs: 6" to 7-1/8" wide. 9 slope. For doors 1-3/4" and over. 10 X 2" phillips flathead screws included.

oFor jambs: 6" to 7-1/8" wide. 9 slope. For doors 1-3/4" and over. 10 X 2" phillips flathead screws included.

o6 slope

COMBO ALUMINUM PRODUCTS, EL CAJON, CATel (619) 447-9200 (800) 457-7500 Fax (619) 442-4558

PRODUCTS ARE SHOWN ACTUAL SIZE(EXCEPT AS NOTED)17

776 A, B

continuedCombination Sill-Thresholds

542 A, B

Full length composite insert for glue down or nail-on applications

1 1/ 8

4 9/16

For jambs:4-1/8” to 5” wide.For doors 1-3/4” and over .Will accept extenders834, 836, & 846shown on page 31.

INSERT SILL-THRESHOLDCOMPOSITE & WOOD SUBSTRATE AVAILABLE

Indicates location of standard fastener hole.

775

7

1/41

3/4

A, B

1/41

7 3/4

THIS DRAWING NOT TO SCALE

THIS DRAWING NOT TO SCALE

oFor jambs: 6" to 7-1/8" wide. 9 slope. For doors 1-3/4" and over. 10 X 2" phillips flathead screws included.

oFor jambs: 6" to 7-1/8" wide. 9 slope. For doors 1-3/4" and over. 10 X 2" phillips flathead screws included.

o6 slope

COMBO ALUMINUM PRODUCTS, EL CAJON, CATel (619) 447-9200 (800) 457-7500 Fax (619) 442-4558

PRODUCTS ARE SHOWN ACTUAL SIZE(EXCEPT AS NOTED)17

776 A, B

Forjambs:6”to71/ 8”wideandcontinuouslevelfloor.9°slope.Fordoors1¾”andover.10x2”phillipsflatheadscrewsareincluded.

Forjambs:6”to71/ 8”wideandcontinuouslevelfloor.9°slope.Fordoors1¾”andover.10x2”phillipsflatheadscrewsareincluded.

For jambs: 5 1/2" to 6-1/2" wide. 6 slope.For doors 1-3/4" and over. 10 X 2" phillipsflathead screws are included.

continuedCombination Sill-Thresholds

For jambs:4-3/8” to 5-1/2” wide.10 X 2-1/2” phillipsflathead screws areincluded.

652 A, B

1 3 /8

1 3 /8

5 3/4

For jambs:4-3/8” to 5-1/2” wide& continuous levelfloor. 10 X 2-1/2”phillips flatheadscrews are included.

653 A, B

660 A, B

5 3/4

6

1/81

11/16

o

For jambs: 5 1/2" to 6-1/2" wide. 6 slope.For doors 1-3/4" and over. 10 X 2" phillipsflathead screws are included.

o

6

1/81

11/16

Indicates location of standard fastener hole.

o 9 slope

o 9 slope

COMBO ALUMINUM PRODUCTS, EL CAJON, CATel (619) 447-9200 (800) 457-7500 Fax (619) 442-4558PRODUCTS ARE SHOWN ACTUAL SIZE15

661 A, B

continuedCombination Sill-Thresholds

6

1/81

3/4

675 A, B

o

6

1/81

3/4

6

3/81

13 /16

Indicates location of standard fastener hole.

For jambs: 5" to 6-1/4" wide. 9 slope.10 X 2" phillips flathead screws areincluded.

oFor jambs: 5" to 6-1/4" wide & continuouslevel floor. 9 slope. 10 X 2" phillipsflathead screws are included.

oFor jambs: 5-1/2" to 6-1/2" wide. 9 slope.For doors 1-3/4" and over. 10 X 2-1/2" phillipsflathead screws are included.

oFor jambs: 5-1/2" to 6-1/2" wide & continuouslevel floor. 9 slope. For doors 1-3/4" and over.10 X 2-1/2" phillips flathead screws are included.

6

3/81

13 /16

COMBO ALUMINUM PRODUCTS, EL CAJON, CATel (619) 447-9200 (800) 457-7500 Fax (619) 442-4558 PRODUCTS ARE SHOWN ACTUAL SIZE 16

676 A, B

680 A, B

681 A, B

continuedCombination Sill-Thresholds

542 A, B

Full length composite insert for glue down or nail-on applications

1 1/ 8

4 9/16

For jambs:4-1/8” to 5” wide.For doors 1-3/4” and over .Will accept extenders834, 836, & 846shown on page 31.

INSERT SILL-THRESHOLDCOMPOSITE & WOOD SUBSTRATE AVAILABLE

Indicates location of standard fastener hole.

775

7

1/41

3/4

A, B

1/41

7 3/4

THIS DRAWING NOT TO SCALE

THIS DRAWING NOT TO SCALE

oFor jambs: 6" to 7-1/8" wide. 9 slope. For doors 1-3/4" and over. 10 X 2" phillips flathead screws included.

oFor jambs: 6" to 7-1/8" wide. 9 slope. For doors 1-3/4" and over. 10 X 2" phillips flathead screws included.

o6 slope

COMBO ALUMINUM PRODUCTS, EL CAJON, CATel (619) 447-9200 (800) 457-7500 Fax (619) 442-4558

PRODUCTS ARE SHOWN ACTUAL SIZE(EXCEPT AS NOTED)17

776 A, B

continuedCombination Sill-Thresholds

542 A, B

Full length composite insert for glue down or nail-on applications

1 1/ 8

4 9/16

For jambs:4-1/8” to 5” wide.For doors 1-3/4” and over .Will accept extenders834, 836, & 846shown on page 31.

INSERT SILL-THRESHOLDCOMPOSITE & WOOD SUBSTRATE AVAILABLE

Indicates location of standard fastener hole.

775

7

1/41

3/4

A, B

1/41

7 3/4

THIS DRAWING NOT TO SCALE

THIS DRAWING NOT TO SCALE

oFor jambs: 6" to 7-1/8" wide. 9 slope. For doors 1-3/4" and over. 10 X 2" phillips flathead screws included.

oFor jambs: 6" to 7-1/8" wide. 9 slope. For doors 1-3/4" and over. 10 X 2" phillips flathead screws included.

o6 slope

COMBO ALUMINUM PRODUCTS, EL CAJON, CATel (619) 447-9200 (800) 457-7500 Fax (619) 442-4558

PRODUCTS ARE SHOWN ACTUAL SIZE(EXCEPT AS NOTED)17

776 A, B

Forjambs:6”to71/ 8”wideandcontinuouslevelfloor.9°slope.Fordoors1¾”andover.10x2”phillipsflatheadscrewsareincluded.

Forjambs:6”to71/ 8”wideandcontinuouslevelfloor.9°slope.Fordoors1¾”andover.10x2”phillipsflatheadscrewsareincluded.