Lubrication Management
Product CatalogueLUBRICATION SYSTEM CONTROLLERS
quality industry solutions
Lubrication Management
Hose & Cable Management
Fire Suppression
Fuel & Fluid Management
Material Dispensing
A structured approach to Engineered Systems
JSG INDUSTRIAL SYSTEMS
Since its inception in 1968, JSG Industrial Systems has been
a proud supplier of quality industrial products, all of which
are designed to reduce maintenance costs and to improve the
management of assets. Our focus is to provide the best possible
technical support, field testing, technical analysis, and ongoing
product development. The reliability of our products is testament to
the structured approach we take to Engineered Industrial Systems.
A STRUCTURED APPROACH
Our portfolio is grouped into 5 key product platforms. This approach
enables us to group together complementary products & solutions,
required for various industrial sectors. Each of our platforms are
supported by a dedicated team of Product Specialists within our
Engineering Systems Technical Support division. These specialists are
available for onsite work, technical training sessions, and of course
after-sales support to our distribution network and end-user markets.
DISTRIBUTOR NETWORK
In each of the geographic areas we support, we have a network
of carefully-selected distributors. These qualified professionals
provide local area support to all of our valued end-user customers.
Each distributor has access to our online systems which gives them
24/7 visibility of service sheets & technical libraries that may be
required in the lifetime of your product. Once systems are installed
and commissioned, our distributors assist with ongoing training,
servicing, upgrades and maintenance.
CONTENTSLubrication Management
Lubrication is an important process
in the management of costs and
machinery. Done correctly, the life
expectancy of the related moving
parts on the machine is significantly
increased. This also has a positive
effect on reducing unplanned
downtime, by minimizing the likelihood
of pins failing and parts seizing.
The advantage of automatic lubrication
systems is that the lubrication is
applied while the machine is operating;
this means that when the equipment
is hot and actually in motion, grease is
being applied to the designated point.
JSG has a proven understanding of
the market needs for lubrication, with
nearly 40 years working in a range of
industries. We understand the needs
with small equipment, all the way
through to some of the largest mining
equipment on earth. JSG can develop a
solution to meet your needs.
JSG Lubrication Management Controller 4
JSG Lubrication Management Controller Data Acquisition 5
JSG “G1” Lubrication Controller 6
JSG “G2” Lubrication Controller 7
Lincoln Solid State 12-24 VDC Timer 8
SKF LMC 101 Controller 9
Lincoln LMC 2 Multi Controller 10
SKF IG502-2 External Controller 11
Single Line Parallel Progressive Dual line Wayside Chain
LUBRICATION SYSTEM TYPE
JSG Industrial Systems | Lubrication System Controllers04
LUBRICATION MANAGEMENT
JSG Lubrication Management Controller
The JSG Lubrication Management Controller is a universal lubrication management system capable of handling applications from simple run/pause systems to the more advanced progressive, single and dual line systems. Innovative algorithms and simple Lube-Logic setup procedure also gives new flexibility and greater control over traditional Single Line Parallel and Two Line systems.
Benefits
� Comprehensive adjustability for run and pause cycles. Variation between five seconds and 24 hours
� Reduce tampering problems with special programming access with lockout
� Powerful Monitoring capability to take sensor feedbacks for cycle monitoring and reservoir low level.
� Fault mode with diagnostic indicators � Data Acquisition for performance analysis through a direct PC
connection or Data Shuttle or Vehicle Modem Kit, refer page 5.
Features
� 12/24 VDC operation with instant system status tests � Compact and lightweight: 300g, size 70mm x 145mm x
38mm deep including mounting plate � Monitors one or two pressure or proximity switches � Short-circuit/open circuit detection � Multiple cycles per lubrication event and cycle counting � Manual override button � External fault lamp output (flash or steady option) � Standard, IP54 for internal mounting or upgraded to IP67 with
special enclosure for external use � Alarm incorporates an LCD readout, integrated audible alarm
output and the ability to set the alarm to pulse or continuous mode
� Data downloading of lube events requires Data Shuttle or Vehicle modem
Specifications
Part No. Complete with Cable 13-002002
Part No. Controller Unit Only 13-002002-1
Part No. Cable Only 13-002002-2
Voltage 12/24 VDC
Dimensions 70 x 145 x 38mm
Weight 300g
Ingress Protection IP54
Lubrication System Type
Single Line Parallel
Progressive
Dual Line
JSG Industrial Systems | Lubrication System Controllers 05
LUBRICATION MANAGEMENT
JSG Lubrication Management Controller Data Acquisition
The programming and data features of the JSG Lubrication Management Controller include the possibility of programming manually or via computer. Software is available for computer programming and downloading operating history. The downloading process can be carried out via direct link, data shuttle or modem/GSM.
Via JSG Data Shuttle
The JSG Lube Management Controller has the capacity to store all critical faults up to 80 records. The Data Shuttle is a compact device that removes the need for a Laptop PC as it can retrieve the data from up to 99 different JSG Lube Management Controllers.
This information can then be downloaded from the Data Shuttle to your desktop PC to the JSG Lube Management program whereby all information can be scrutinized.
� Remote downloading of data without the need for a laptop
� Retrieve information from up to 100 different controllers
� The Data Shuttle is self-powered with solid state memory for data storage without the risk of loss
Via JSG GSM Vehicle Modem Kit
The JSG Vehicle Modem Kit is the ultimate tool for downloading data from the Lube Management Controller.
Connecting the JSG Vehicle Modem Kit to the JSG Lube Management Controller allows remote monitoring via the cellular network and therefore reducing inspection frequency and valuable technician time.
� The GSM modem needs to be installed together with the Lube Management Controller.
� Allows for central offsite location for where data from multiple remote sites can be gathered.
� Each modem has its identity and unique address.
Specifications
Part No. 13-003600
Voltage 12/24 VDC
Dimensions 70 x 145 x 38mm
Weight 300g
Ingress Protection IP54
Specifications
Part No. 13-004002
JSG Industrial Systems | Lubrication System Controllers06
LUBRICATION MANAGEMENT
JSG “G1” Lubrication Controller
The G1 provides the one control output functionality in a practical housing, simple wiring and clear programming make this the best no fuss controller available for Progressive, Centro-Matic and Dual Line applications.
Benefits
� Can fit almost anywhere. The compact proportions and weight of the G1 allows it to fit into most new and existing setups with minimal impact
� Simple Programming via the fascia controls results in almost effortless commissioning. No pin jumpers or dipswitches means the housing can stay shut
� Clear indication of status or faults through labelled LED indicators � Powerful monitoring capability through feedback sensors for
lubrication cycle and reservoir low level monitoring � Avoid tampering with special programming access
Features
� Run and Pause timing adjustable from 1 second to 50 hours � External fault lamp � Low level indicator light � Cycle counting � Test mode allows the user to verify an installation and diagnose
faults � Non-volatile memory � Simple connection with pre-made looms available � Built in fuse � Manual override button � Includes mounting bracket
Specifications
Part No. Complete with Cable 13-002100
Part No. Controller Unit Only 13-002100-1
Part No. Cable Only 13-002100-2
Voltage 12/24 VDC
Dimensions 62 x 94 x 38mm
Weight 150g
Ingress Protection IP54
Lubrication System Type
Single Line Parallel
Progressive
Dual Line
One Output
JSG Industrial Systems | Lubrication System Controllers 07
LUBRICATION MANAGEMENT
JSG “G2” Lubrication Controller
The economical model “G2” Pulse Lubrication Controller is suitable for Single Line Parallel injector lubrication systems. The G2 Controller has 2 outputs, one output specially designed to control motors that require a pulse signal to reciprocate, while the other output is used to keep the vent valve open during a lubrication cycle.
Benefits
� Can fit almost anywhere. The compact proportions and weight of the G2 allows it to fit into most new and existing setups with minimal impact
� Simple Programming via the fascia controls results in almost effortless commissioning. No pin jumpers or dipswitches means the housing can stay shut
� Clear indication of status or faults through labelled LED indicators � Powerful monitoring capability through feedback sensors for
lubrication cycle and reservoir low level monitoring � Avoid tampering with special programming access
Features
� Pause time: 1 second to 50 hours � Max run time/over pressure monitor: 1 second to 50 minutes � Pump run pressure timeout range: 1 to 50 minutes � Solenoid valve cycle time: 1 to 50 seconds � External fault lamp output � Low level indicator light � Test mode allows the user to verify an installation and diagnose
faults � Non-volatile memory � Simple connection with pre-made looms available � Built in fuse � Manual override button � Monitors pressure cycles via timeout alarm � Includes mounting bracket
Specifications
Part No. Complete with Cable 13-002500
Part No. Controller Unit Only 13-002500-1
Part No. Cable Only 13-002500-2
Voltage 12/24 VDC
Dimensions 62 x 94 x 38mm
Weight 150g
Ingress Protection IP54
Lubrication System Type
Single Line Parallel*
Note: *Use with reciprocating pumps requiring pulse signal only.
Two Outputs
JSG Industrial Systems | Lubrication System Controllers08
LUBRICATION MANAGEMENT
Lincoln Solid State 12-24 VDC Timer
The Lincoln Solid State microprocessor-based controller is designed for use with systems installed on mobile machinery, such as earth moving equipment and off highway type and construction vehicles utilizing the storage battery for power. The timer is of solid state design with isolating output relay and external connections with positive or negative ground battery connections.
Benefits
� Rugged construction with liquid and dust-tight enclosure � Reliable solid state memory for controlling the pump � Simple programming allows for ease of use
Features
� Pause time: 2.5 to 80 minutes � Run Time: 75 seconds fixed � Switching Capacity: 5 Amps � Rugged construction � Simple timer adjustment � Includes manual remote push-button
Specifications
Part No. 01-084015
Voltage 10/30 VDC, 25 A
Dimensions 133 x 79 x 76mm
Weight 763g
Ingress Protection NEMA 12
Operating Temperature 18 to 55°C
Lubrication System Type
Single Line Parallel
JSG Industrial Systems | Lubrication System Controllers 09
LUBRICATION MANAGEMENT
SKF LMC 101 Controller
The versatile SKF LMC 101 controller operates as a timer or controller on Single Line Parallel or Progressive lubrication systems. Developed for use on off-road and mobile equipment, the LMC 101 also is suitable for many low voltage industrial lubrication applications, such as those found in food and beverage, pulp and paper and steel markets.
Benefits
� Reduce tampering problems; settings can only be modified by a technician with PC software connected to the controller
� Powerful Monitoring capability to take sensor feedbacks for cycle monitoring and reservoir low level
� Direct control to FlowMaster or high current pump. The LMC 101 Controller integrated with high current switching relay
� Records history of system operation for performance and fault analysis by a technician when PC software is connected to the controller
Features
� Pause time: 15 seconds to 99 hours � Run Time: 15 seconds to 99 minutes � Can operate with 12 or 24 VDC power supply. � Configured using PC software and USB connection � Functions as a timer or controller � Records history of system operation and fault codes � Uses pressure switch or pressure transducers (1-6 VDC; or 4-20 mA)
in controller mode � LED indicators show power, pump function, low-level fault and
system faults � Manual lubrication cycle activation button � Data logging includes date and time of alarms, power ups,
configuration changes, lubrication cycles and totals lubrication count, manual lubrication count, pressure alarm, low levels and pump on-time information
� Four inputs: – Two pressure switches, pressure transducers or piston detectors – Remote manual lubrication switch – Low-level switch
� Four outputs: – Pump – Low-level alarm relay – System fault relay – Vent solenoid
Specifications
Part No. 01-086535
Voltage 12/24 VDC
Dimensions 150 x 118 x 60mm
Weight 400g
Ingress Protection NEMA 12
Operating Temperature -40 to 66°C
PC Software 01-086535
Lubrication System Type
Single Line Parallel
Progressive
NEW
JSG Industrial Systems | Lubrication System Controllers10
LUBRICATION MANAGEMENT
Lincoln LMC 2 Multi Controller
The LMC-2 is Lincoln’s Flagship lubrication controller. It can be used to control, monitor and manage any type of lubrication system from Progressive, Dual Line and Single Line systems; to highly specialised lubrication systems such as PMA, ORSCO and COBRA 1X chain systems.
Benefits
� Comprehensive range of integrated lubrication programs for controlling any type of lubrication system
� Wide range of status monitoring capabilities with 8 inputs/5 outputs
� Intuitive step-by-step instructions and visual display results in straight forward controller programming
� Flexibility of fully programmable controllers with the cost effectiveness of pre-programmed controllers
� Simple and powerful interfacing with common field-bus systems
Features
� All settings and count values are saved every 30 minutes in the LMC2 EEPROM, even if the mains supply fails
� Time dependent intervals and integrated counter for facilitating cycle-dependent control of the lubrication intervals
� Complete range of status indicator LED lamps and 44x7 segment display
� Up to 8 digital inputs � Up to 4 relay outputs and 1 electronic output � Typical monitoring capabilities for operation/fault, pump on, low-
level � Field bus and program interfacing
Specifications
Part No. 02-236-10567-6 02-236-10567-5
Voltage 240 VAC 50/60 Hz 24 VDC
Dimensions 200 x 120 x 90mm 200 x 120 x 90mm
Weight 1kg 0.7kg
Ingress Protection
IP54 IP54
Operating Temp
-10 to 70°C -10 to 70°C
Lubrication System Type
Single Line Parallel
Progressive
Dual Line
Wayside
Chain
JSG Industrial Systems | Lubrication System Controllers 11
LUBRICATION MANAGEMENT
SKF IG502-2 External Controller
The IG502-2 controller was designed by SKF as an external controller for the SKF KFG progressive pumps and systems. However, it can be used to run typical progressive type lubrication systems or single line applications making it a versatile and economic controller solution.
Benefits
� Dual integrated programs provide a powerful yet flexible controller solution for typical progressive or single line lubrication systems
� Fault and status monitoring capability through the use of pressure switch; cycle monitor and low level feedback sensors
� Clear Status indication through LCD display and warning indicator lamps
Features
� Pause time: 0.1 to 99.9 hours � Run time: 0.1 to 99.9 minutes � Suitable for mobile and industrial plant applications � Can be programmed to run off external pulse input, EG from
machine movement � Records periods of faults for data analysis � Fault and stoppage hour recording which can be viewed by LCD
display � Monitoring- reservoir low level, pump run time, pressure switch
(single line) or block cycle monitoring
Specifications
Part No. VGEEIG502-2-E+912
VGEEIG502-2-E+924
Voltage 12 VDC 24 VDC
Dimensions 138 x 65 x 40mm 138 x 65 x 40mm
Weight 0.175kg 0.175kg
Ingress Protection
IP20 IP20
Operating Temp
-25 to 75°C -25 to 75°C
Assoc. Cable Harness
VGKP997-000-373 (KFU Pumps)
VGKP997-000-373 (KFU Pumps)
Lubrication System Type
Single Line Parallel
Progressive
Every effort has been made to ensure all information and photographs contained in this publication were correct and accurate at time of printing, however no warranty is given in respect of this publication and JSG Industrial Systems Pty Ltd (JSG) shall not be liable for any error therein. Technical information, specifications and products shown may be subject to change without prior notice. Pictures shown are for illustration purposes only. WARNING: For sale and proper use consult instructions, the supplier or JSG. Contact your nearest JSG Distributor for latest information.
© 2015 JSG Industrial Systems Pty Ltd., All rights reserved. LC0615
www.jsgindustrial.com
HEAD OFFICE
Unit 1, 21 Amour St Revesby NSW 2212
PO Box 333 Milperra NSW 2214
Ph: (02) 9914 8720 Fax: (02) 9914 8798
Email: [email protected]
Sydney | Melbourne | Perth | Brisbane | Adelaide | Townsville | Mackay | Indonesia