Product information,Product information,Features & benefitsFeatures & benefits

EUROBLOC VT Main characteristics

Particularities- Minimum displacement of hook block

- Best C dimension of the market

- Best hook approach of the market

- Variable travelling speed (2 control modes, MS control in standard)

- Hook with handle

- Hoisting speed ratio is 1/6, between 1/4 and micro

speed for smooth startingSpeed Speed

Time Time

www.emmegiesse.comwww.emmegiesse.com

EUROBLOC VT Main characteristics

EUROBLOC VT Main characteristics

Particularities (part 2)- Hoisting brake setting for the hoist life (in normal use)

and with dust protection

- Cooling of the motor increased of 30% (tunnel effect)

- Rope guide for all types of environment (dusty, clean,…)

- High quality rope for long life service (flexibility, parallel lay)

- Automatic low hoisting speed at C approach.

- Phase fault safety hoisting limit switch

- Modular construction with the minimum of parts

- Easy maintenance

- Wide range of features

www.emmegiesse.comwww.emmegiesse.com

EUROBLOC VT Main Sales Arguments

Safety

Travelling. Variable travelling speed for precise positioning of loads.Wire rope. in galvanized steel as a standard, high safety factor (factor 4,6 -FEM2m).Electrical cubicle. The cover can be folded back so that you can store your toolsfor maintenance (the cover has two steel safety wires to prevent it from falling).MT2. Electronic control of the recording of hoist solicitation status.Electrical. Low voltage control for more safety.Traverse wheels. The 4 steering wheels are fully streamlined for improved safety.Hook and pulley block. Rotating hook and pulley block with safety latch.

www.emmegiesse.comwww.emmegiesse.com

EUROBLOC VT Main Sales Arguments

Easy maintenance

Hoisting motor. Motor cooling increased by 30 % (tunnel effect)Hoisting brake . The brake is tested for hoist longevity under normal use conditions.Steering motor-reducer. Steering reducer with one rail and a permanently lubricated connection.Drum. The drum has been completely covered for better protectionRope guide. Built “without spring” so that it can be more easily replaced during maintenance.Electrical cubicle. The wires go in and out by means of steel plugs that can be unbound and that are built into the caseMT2. Calculation of the SWP (Safe Working Period)Assembly is in modules, for easier management of spare parts for replacementSurface treatment. 2- component epoxy paint with 120 µ for greater protection

www.emmegiesse.comwww.emmegiesse.com

EUROBLOC VT Main Sales Arguments

Ergonomics

Hook and pulley block. Ergonomical hook (area to grab and hold).Push button box. Made with tinted polypropylene, grounded, with doubleinsulation, ergonomical (IP 65 protection). Optional load display availableElectrical cubicle. Located on the side of the hoist, easily accessible.The open / close system uses a quick closure method.

www.emmegiesse.comwww.emmegiesse.com

EUROBLOC VT Main Sales Arguments

High technology

Pulley block. Only a small shift of the pulley block for hoisting (lifting is almost perfectly centred).Rope guide. The guidance system does not get dirty, which allows for use in any type of environment.Drum. A very high wire rope / drum diameter ratio (twice as large as the standard one), which:• Increases the longevity of the wire rope.• Reduces the approach data of the hoist.• Reduces the “C” approach data of the hook.Electrical case. Quite large, it is equipped with the speed variation module as a standardLifting gearbox. Direct impulse gearbox unit, helicoid toothed gears, permanently lubricated,detector to prevent pressure overload.Optimal positioning of steering rollers. The 4 steering rollers equally share the load in

order to optimise your tracks

www.emmegiesse.comwww.emmegiesse.com

EUROBLOC VT Main Sales Arguments

Savings Hoisting motor. 60 % operating factor and tropicalised as a standard for greater longevityTravelling motor. Tropicalised as a standard for greater longevityPulley block. The best «C» dimension on the market for optimal use of the size of your buildings and optimal use of work areasTravelling. Variable travelling speed to reduce wear on steering rollersLoad limiter. As ordered by the directive on “Machines” (required equipment). All EUROBLOC VTs are equipped with a load limiter as a standard (safety measure in the event of hoist overload). For greater longevityHook and pulley block. Doesn’t take up much space, permanently lubricated rollers,pulleys are in GGG cast iron, very resistant. A high pulley / wire rope diameter ratio gives the wire rope greater longevity.

www.emmegiesse.comwww.emmegiesse.com

• Foot mounted version• Normal headroom trolley version• Short headroom trolley version • Double girder trolley version

EUROBLOC VT Version

www.emmegiesse.comwww.emmegiesse.com

EUROBLOC VT Special execution

EUROBLOC EXExplosion proof and / orspark proof version

www.emmegiesse.comwww.emmegiesse.com

EUROBLOC VT Trolley

FOOT MOUNTED (FIXED)The foot mounted hoist is fixed to the floor with 6 screws. The end point position, reversing pulley and big drum diameter allow to have a very small C dimension and a compact hoist. A fixed suspended hoist is available in option.

www.emmegiesse.comwww.emmegiesse.com

EUROBLOC VT TrolleyLOW HEADROOM TROLLEY The LHT construction with a medium end point position, a medium reversing pulley position and a big drum diameter allow to have a very small C dimension.On one side of the girder, there is the hoisting machinery and on the other side, There are the travelling machinery and the electric cubicle, so that allows to balance the weight to each side of the girder (only 1 or 2 small counter-weight) and the width of the hoist is smaller.The C-dimension (distance between the hook and the running surface of the girder) is according tothe girder width (B) and to the load.

www.emmegiesse.comwww.emmegiesse.com

EUROBLOC VT TrolleyPERPENDICULAR DOUBLE GIRDER TROLLEYThe DGT has a high, medium or low construction (hoist is between the end-truck). The hoist is fixed to only one box girder thanks to two plates with an articulation for the maintenance. The cubicle is fixed to the other side of the box girder on the travelling machinery side.

Smaller and bigger rail gauge are possible as different heights of box girder.

www.emmegiesse.comwww.emmegiesse.com

EUROBLOC VT General

• 2-year warranty • Product complies with CE regulations • Manufacturing is ISO9001 certified  • Each hoist is tested in VERLINDE facilities and delivered with individual test report  • All main components are manufactured by our group or under our quality surveillance. 

www.emmegiesse.comwww.emmegiesse.com