Product Selector GuideMetering Power Supply ICs
November 2016
2
Product Selector Guide
0 W 1 W 2 W 3 W 5 W 4 W 10 W 14 W 16 W 18 W 20 W 30 W 118 W 177 W
CV ±2%SSR
85-265 VAC
0 mA 80 mA 120 mA 240 mA 360 mA Output Current
CV ±5%PSR
CV ±5%
CV ±5%CC ±10%
PSR
LinearTransformer/
LooseCV/CC
PSR
LinkSwitch-3
LinkSwitch-4
LinkSwitch-CV
LinkSwitch-HP
LinkSwitch-LP
Non-Isolated Buck or Buck-Boost
Output Characteristics and Power
Primary-Side Regulation Flyback
Secondary-Side Regulation Flyback
™
PI-minimeteringchart-101316
LinkSwitch™-TN2
TinySwitch™-4
TOPSwitch™-JXLinkSwitch-XT
CV ±2%CC ±5%
SSR
Incorporates PrimaryMOSFET, Flyback and
Synchronous Rectification Driver
InnoSwitch™-EP
3
IC Product Tables
LinkSwitch-TN2 – Highly Energy Efficient Off-line Switcher IC with Integrated System Level Protection for Low Component-Count Power Supplies1
Product4
230 VAC ± 15% 85-265 VAC
MDCM2
(mA)CCM3
(mA)MDCM2
(mA)CCM3
(mA)
LNK3202P/G/D 63 80 63 80
LNK3204P/G/D 120 170 120 170
LNK3205P/G/D 175 270 175 270
LNK3206P/G/D 225 360 225 360
Additional Features:• 725 V internal MOSFET rating• Self-powered• ON/OFF control• Hysteretic thermal shutdown• Power limiting• Frequency jitter reduces EMI• EcoSmart™ low standby/no-load power consumption
Notes:1. Typical output current in a non-isolated buck converter with devices operating at default current limit and adequate heat sinking. Output
power capability depends on respective output voltage and thermal requirements. See Key Applications Considerations Section for complete description of assumptions, including fully discontinuous conduction mode (DCM) operation.
2. Mostly discontinuous conduction mode. 3. Continuous conduction mode. 4. Packages: P: PDIP-8C, G: SMD-8C, D: SO-8C.
LinkSwitch-CV / LP / XT – Very Low Power AC-DC Power Conversion
Product3,4
Continuous Output Power (W)
Continuous Output Power (W)
Open Frame2
Open Frame2
LinkSwitch-CV 230 VAC ± 15% 85-265 VAC
LNK623P/D 9 6
LNK624P/D 11 6.5
LNK625P/D 13.5 8
LNK626P/D 17 10
LinkSwitch-LP 230 VAC ± 15% 85-265 VAC
LNK562P/G/D 1.9 1.9
LNK563P/G/D 2.5 2.5
LNK564P/G/D 3 3
LinkSwitch-XT 230 VAC ± 15% 85-265 VAC
LNK362P/G/D 2.8 2.6
LNK363P/G/D 7.5 4.7
LNK364P/G/D 9 6
Additional Features:• 700 V internal MOSFET rating• Self-powered• ON/OFF control• Hysteretic over-temperature protection• Power limiting• Frequency jitter reduces EMI• EcoSmart low standby/no-load power consumption
Notes:1. Minimum continuous power in a typical non-ventilated enclosed
adapter measured at 50 °C ambient. 2. Minimum practical continuous power in an open frame design
with adequate heat sinking, measured at 50 °C ambient. 3. Packages: P: DIP-8B, G: SMD-8B, D: SO-8C.4. Packages: P: DIP-8C, G: SMD-8C, D: SO-8C.
LinkSwitch-3 – Energy-Efficient, Accurate Primary-Side Regulation CV/CC Switcher for Adapters and Chargers1,2,3,4
Product5
90-264 VAC
D (SO-8C) Package
Open Frame (W)
LNK6404D / LNK6424D 4.1
LNK6405D / LNK6415D / LNK6425D 5.1
LNK6406D / LNK6416D /LNK6426D / LNK6436D / LNK6446D
6.1
LNK6407D / LNK6417D / LNK6427D 7.5
Product5
E (eSIP-7C) and K (eSOP-12B) Packages
Open Frame (W)
LNK6407K / LNK6417K / LNK6427K 9
LNK6408K / LNK6418K / LNK6428K / LNK6448K 10
LNK6408E / LNK6418E /LNK6428E / LNK6448E 10
Additional Features:• Compensates for transformer inductance tolerances• Compensates for input line voltage variations• Compensates for cable voltage drop• Compensates for external component temperature variations• Very accurate IC parameter tolerances using proprietary trimming
technology • Frequency jittering greatly reduces EMI filter cost• Even tolerances achievable with external resistor selection/trimming• Programmable switching frequency up to 85 kHz to reduce
transformer size• Minimum operation frequency fixed to improve transient load
response
Notes: 1. Assumes minimum input DC voltage >90 VDC, KP ≥1 (Recommend KP
≥1.15 for accurate CC regulation), η >78%, DMAX <55%.2. Output power capability is reduced if a lower input voltage is used.3. Minimum continuous power with adequate heat sink measured at 50 °C
ambient with device junction below 110 °C.4. Assumes bias winding is used to supply BYPASS pin.5. Package: D: SO-8C, E: eSIP-7C, K: eSOP-12B.
4
IC Product Tables
TinySwitch-4 – Energy-Efficient, Off-Line Switcher with Line Compensated Overload Power
Product3
Peak or Open Frame2 (W)
Peak or Open Frame2 (W)
230 VAC ± 15% 85-265 VAC
TNY284P/D/K 11 8.5
TNY285P/D 15 11.5
TNY285K 15 11.5
TNY286P/D 19 15
TNY286K 19 15
TNY287P 23.5 18
TNY287D 23.5 18
TNY287K 23.5 18
TNY288P 28 21.5
TNY288D 26 19.5
TNY288K 28 21.5
TNY289P 32 25
TNY289K 32 25
TNY290P 36.5 28.5
TNY290K 36.5 28.5
Additional Features:• 725 V internal MOSFET rating• Self-powered• Hysteretic thermal shutdown protection• Frequency jitter reduces EMI• EcoSmart low standby/no-load power consumption• On-time extension• Latching output overvoltage protection• Line undervoltage lockout• Selectable current limit
Notes:1. Minimum continuous power in a typical non-ventilated enclosed
adapter measured at +50 °C ambient. Use of an external heat sink will increase power capability.
2. Minimum peak power capability in any design or minimum continuous power in an open frame design.
3. Packages: P: DIP-8C, D: SO-8C, K: eSOP-12B.
Notes:1. PCB heat sink with wave soldering. 2. Packages: E: eSIP-7C, K: eSOP-12B, V: eDIP-12B.
LinkSwitch-HP – Energy Efficient, High-Power Off-Line Switcher with Accurate Primary-Side Regulation (PSR)
Product2 HeatSink
230 VAC ±15% 85-265 VAC
Open Frame (W) Open Frame (W)
LNK6xx3K/V PCB-W1 25 15
LNK6xx3E Metal 35 27
LNK6xx4K/V PCB-W1 28 20
LNK6xx4E Metal 47 36
LNK6xx5K/V PCB-W1 30 22
LNK6xx5E Metal 593 45
LNK6xx6K/V PCB-W1 34 26
LNK6xx6E Metal 883 683
LNK6xx7K/V PCB-W1 41 30
LNK6xx7E Metal 117 90
LNK6xx8K/V PCB-W1 47 34
LNK6xx8E Metal 135 104
LNK6xx9K/V PCB-W1 54 39
LNK6xx9E Metal 153 118
Additional Features:• EcoSmart – energy efficient
• Multi-mode control maximizes efficiency• No-load consumption below 30 mW at
230 VAC (LNK67xx)• >75% efficiency with 1 W input at 230 VAC• >50% efficiency with 0.1 W input at 230 VAC
• High design flexibility for low system cost• Dramatically simplifies power supply designs
• Eliminates optocoupler and all secondary control circuitry• ±5% or better output voltage tolerance
• 132 kHz operation reduces transformer and power supply size• Accurate programmable current limit
• Compensation over line limits overload power• Frequency jittering reduces EMI filter cost
5
IC Product Tables
Additional Features:• A Highly Integrated, Compact Footprint
• Incorporates flyback controller, 725 V / 900 V MOSFET, secondary-side sensing and synchronous rectification driver
• FluxLink™ integrated, HIPOT-isolated, feedback link • Exceptional CV accuracy, independent of transformer design or
external components• Excellent multi-output cross regulation with weighted SSR feedback
and synch FETs• EcoSmart – Energy Efficient
• <10 mW no-load at 230 VAC when supplied by transformer bias winding
• Easily meets all global energy efficiency regulations• Advanced Protection / Safety Features• Primary sensed output OVP
• Secondary sensed output overshoot clamp• Secondary sensed output OCP to zero output voltage• Hysteretic thermal shutdown• Input voltage monitor with accurate brown-in/brown-out and
overvoltage protection• Full Safety and Regulatory Compliance
• 100% production HIPOT compliance testing equivalent to 6 kV DC/1 sec
• Reinforced insulation• Isolation voltage >3,500 VAC for INN26xx series, >4,000 VAC for
INN2904 series• UL1577 and TUV (EN60950) safety approved• EN61000-4-8 (100 A/m) and EN61000-4-9 (1000 A/m) compliant
• Green Package• Halogen free and RoHS compliant
• Applications• Appliance, industrial, and smart lighting
InnoSwitch-EP – Off-Line CV/CC Flyback Switcher IC with Integrated 725 V / 900 V MOSFET, Sync-Rect Feedback with Advanced Protection
Product3
Peak or Open Frame1,2 (W)
725 V MOSFET
230 VAC ±15% 85-265 VAC
INN2603K 24 15
INN2604K 27 20
INN2605K 35 25
Product3900 V MOSFET
230 VAC ±15% 85-484 VAC
INN2904K 29 20
Notes: 1. Minimum continuous power in a typical non-ventilated enclosed typical size adapter measured at 40 °C ambient. Max output power is dependent on the design. With
condition that package temperature must be < = 125 °C.2. Minimum peak power capability.3. Package: K: eSOP-R16B.
6
Design Examples
LinkSwitch-TN2 – Non-Isolated Output Buck (RDK-506)1.44 W, 12 V, 120 mA OUTPUT, 85 – 265 VAC INPUT, NON-ISOLATED BUCK APPLIANCE POWER SUPPLY
RTN
TP4
12 V,120 mA
TP3
L
TP1
N
TP2
85-265VAC
PI-8052-100716
FB BP/M
SD
LinkSwitch-TN2C14.7 µF400 V
C3100 nF50 V
D2GS1M-LTP
D1GS1M-LTP
D3ES1JE-TPU1
LNK3204D/G/P
D4DFLR1600-7
600 V
C5100 µF25 V
RF18.2 Ω2 W
R218.7 kΩ
1%1/8 W
R326.7 kΩ
1%1/8 W
R14.12 kΩ
1%1/8 W
L11000 µH
L21000 µH
C24.7 µF400 V
C410 µF35 V
R420 kΩ1%
1/8 W
LinkSwitch-TN2 – Non-Isolated Buck (DER-507)175 mW, 5 V, 35 mA OUTPUT, 85 – 265 VAC INPUT, NON-ISOLATED BUCK APPLIANCE POWER SUPPLY
RTN
TP4
5 V,35 mA
TP3
N
TP2
L
TP1
85-265VAC
PI-8132-100616
FB BP/M
SD
LinkSwitch-TN2
C21 µF35 V
D1S1ML
D2UFM15PL-TPLNK3202D
D3DFLR1600-7
600 V
C5100 µF10 V
R1220 Ω1/2 W
R2220 Ω1/2 W
RF18.2 Ω2 W
R42.94 kΩ
1%1/10 W
R32.00 kΩ
1%1/10 W
L13300 µH
C12.2 µF400 V
C410 µF16 V
R5680 Ω1/10 W
7
Design Examples
LinkSwitch-TN – Ultra Wide Input Range Power Supply (DI-124)3 W, 12 V, 250 mA OUTPUT, 57 – 580 VAC INPUT FLYBACK POWER SUPPLY
PI-4487-102210
D
S
FB
BP
R5 1 k
L1 1 mH
R13 475 kΩ 0.5 W R14
475 kΩ 0.5 W
R6 680 kΩ 0.5 W
R7 680 kΩ 0.5 W
R10 200 Ω
R12 1 kΩ
R11 330 Ω
R8 680 kΩ 0.5 W
R9 10 Ω
R16 475 kΩ 0.5 W R15
475 kΩ0.5 W
R1
10 Ω 1 W R2
10 Ω 1 W
R3
10 Ω 1 W
R4
10 Ω 1 W
C7 15 µF 450 V
C5 15 µF 450 V
C4 100 nF 50 V
U1LNK304PN
U2B PC817A
U2A PC817A
C6 15 µF 450 V
C8 15 µF 450 V
C1 2.2 nF
250 VAC
L2
Ferrite Bead
C9 5.6 nF 1 kV
C2 470 µF 16 V
T1
EEL16
C3 100 µF 16 V
D10 UF4004
NC 4
1
5
7 9
10
Q1 IRFBC20
D9 UF4007
D1 1N4007
D2 1N4007
D3 1N4007
D4 1N4007
D5 1N4007
D6 1N4007
D7 1N4007
D8 1N4007
VR1P6KE150A
VR5 P6KE150A
VR41N5245B
15 V
VR6 BZX79-C11
11 V
VR2P6KE150A
VR3P6KE150A
PH1
12 V, 250 mA
RTN
PH2
PH3
N
LinkSwitch-TN
LinkSwitch-XT – Tamper Proof Energy Meter Power Supply (DER-141)0.75 W, 5 V, 150 mA OUTPUT, 85 – 265 VAC INPUT FLYBACK POWER SUPPLY
R175 kΩ1/2 W
C51 nF 1 kV
R291 Ω1/8 W
R3100 Ω1/8 W
RF18.2 Ω2.5 W
C14.7 µF400V
C24.7 µF400V
C3470 µF
10V
C6680 pF
250 VAC
C4100 nF
50V
U2PC817A
VR1BZX79B3V9
3.9 V, 5%
T1E75-8
NC4
8
5
NC
U1LNK363DN
L11 mH
D11N4007
D31N4007
D61N4007GP
D51N5818
D21N4007
D41N4007
5 V, 150 mA
85 - 265VAC
RTN
PI-4665-041508
D
S
FB
BP
LinkSwitch-XT
1,2
8
Design Examples
LinkSwitch-XT – High Efficiency Constant Voltage Adapter (EPR-89)2 W, 6.2 V, 322 mA OUTPUT, 85 – 265 VAC INPUT, FLYBACK POWER SUPPLY
PI-4205-042613
D
S
FB
BP
D11N4005
D21N4005
D51N4934
D31N4005
D41N4005
RF18.2 kΩ2.5 W
R13.9 k1/8 W
R3390 Ω1/8 W
R21 k
1/8 W
6.2 V,322 mA
85 - 265VAC
J3-1
RTN
J3-2
J2
J1
L11 mH
L21 mH
C13.3 µF400 V
C23.3 µF400 V
C4*100 pF
250 VAC
C5330 µF16 V
VR1BZX79B5V1
5.1 V, 2%
*Optional component
T1EE164
5
3
9
8
NC NC
C3100 nF50 V
U2PC817A
U1LNK362PN
LinkSwitch-XT
LinkSwitch-CV – 2-Output Constant Voltage Power Supply (DER-213)3.8 W, 12 V, 0.25 A, and 5 V, 0.15 A DUAL OUTPUT, 85 – 265 VAC INPUT FLYBACK POWER SUPPLY
PI-5405-040309
D
S
FB
BP
U1LNK623PG
LinkSwitch-CV
R15.1 kΩ
L12200 µH
D11N4007
D21N4007
D31N4007
D41N4007
D51N4007GP
D6SB1100
D7SB140
L22200 µH
L33.3 uH
RF110 Ω2 W
R511 kΩ1%
R3330 kΩ
R66.65 kΩ
1%
R751 Ω
T1
EF16
NC
81
3 5
6,7
4
2
R25.1 kΩ
C31 nF1 kV
C14.7 µF400 V
C210 µF400 V
C41 µF25 V
C5220 µF10 V
C647 µF16 V
C7330 µF16 V
C8680 pF100 V
R4300 Ω
85 - 265VAC
12 V, 0.25 A
5 V, 0.15 A
RTN
9
Design Examples
LinkSwitch-3 – Low Power Constant Voltage, Constant Current Charger/Adapter (DER-403)10 W, 2 V, 1 A OUTPUT, 90 – 265 VAC INPUT FLYBACK POWER SUPPLY
PI-7209-020515
D
S
FB
BP
R11200 kΩ
R22.55 kΩ
1%
R3150 Ω
R644.2 kΩ
1%
R52.4 Ω
D3RS1ML
R82.37 kΩ
1%
R110 Ω
R104.7 kΩ
R710 kΩ1%
D2S1ML
D1SBR1045SP5-13
T1EPC17
5 FL1
FL2
4
3
6
C4680 µF10 V
C51 nF50 V
C3680 µF10 V
C110 µF400 V
C215 µF400 V
C71 µF50 V
C810 µF25 V
L21 mH
L1Ferrite Bead
(3.5 × 7.6 mm)
L3Ferrite Bead
(3.5 × 7.6 mm)
C6470 pF250 V
U1LNK6448K
LinkSwitch-3
BR1B10S-G1000 V
RT110 Ω
F11 A tO
90 - 265VAC
LTP1
NTP2
5 V, 2 A
J1-1
RTN
J1-4
LinkSwitch-4 – 3-Output, Isolated Flyback Power Supply (DER-479)6 W, 11 W PK, 3.3 V, 150 mA, 8 V, 500 mA and 12 V, 1 A OUTPUTS, 185 – 440 VAC INPUT, NON-ISOLATED FLYBACK POWER SUPPLY
PI-7628-051915
LinkSwitch-4U1
LNK4004D
GND
BD
ED
CS
VCC
SBD
FB
R2215 Ω
1 10
3
9
7
6
5
8
D5ES1B-LTP
Q1BUL216
R13330 kΩ
1W
R1247 Ω1/8 W
R939 Ω1%1 W
R3220 Ω1/8 W
185 - 440VAC
12 V,100 mA
8 V, 500 mA
4 V,150 mA
RTN
L
N
BR1B10S-G1000 V
R15100 Ω1%
1/8 W
R40.56 Ω
1%
D1RS1ML
D4ES1B-LTP
D3, 30BQ100PBF
R1127 MΩ
R26750 kΩ
R27750 kΩ
R28750 kΩ
Optional
R8580 kΩ
R6580 kΩ
R5580 kΩ
R7580 kΩ
R1027 MΩ
L11500 µH
C16680 pF200 V
R254.7 kΩ1/4 W
R1610 kΩ1/4 W
R2415 Ω
R2315 Ω
C15680 pF200 V
C12220 µF35 V
C17220 µF35 V
C10220 µF35 V
C18680 pF200 V C19
10 µF16 V
C215 µF400 V
C415 µF400 V
C315 µF400 V
C515 µF400 V
R174.7 kΩ
C14470 pF1000 V
C6330 nF600 V
T1EF20
4 D2
BAV2
1WS-
7-F
R219.76 kΩ
1%1/16 W
R203.01 kΩ
1%1/16 W
R143.3 Ω1/8 W
C82.2 µF25 V
10
Design Examples
TinySwitch-4 – Universal Input Adapter (RDK-399)12 W, 12 V, 1 A OUTPUT, 85 – 265 VAC INPUT FLYBACK POWER SUPPLY
LinkSwitch-HP – 2-Output, Constant Voltage Power Supply (RDK-321)17 W, 5 V, 1 A and 18 V, 670 mA OUTPUT, 90 – 265 VAC INPUT FLYBACK POWER SUPPLY
D
S
BP/M
EN/UV
L11 mH
D11N4007
RV1275 VAC
F11 A
D21N4007
C16.8 µF400 V
C622 µF50 V
C8*1 µF50 V
C9*10 µF50 V
C222 µF400 V
C101000 µF
25 V
C52.2 nF
250 VAC
C11100 µF25 V
12 V, 1 A
J3
J1
J2
85 - 265VAC
RTN
J4
C7100 nF50 V
U1TNY288PG
C410 nF1 kV
VR1P6KE150A NC 8
6
4
T1EE25
5
1
3
D51N4007GP D6
UF4003
D7SB3100-T
U2PC2501
VR21N5245B
15 V
VR3BZX55-C11
11 V
*R5, R8, C8 and C9 are optional components
R5*3.6 MΩ
R347 Ω1/8 W
R42 kΩ1/8 W
R6390 Ω1/8 W
R72.2 Ω
R8*6.8 kΩ
1%
R11 kΩ
R2100 Ω
D31N4007
D41N4007
L2Ferrite Bead
3.5 × 7.6 mm
PI-7268-041214
TinySwitch-4
PI-6861-032714
C92.2 nF
250 VAC
VR11SMB59BT3G
120 V
L122 mH
BR1DF06M600 V
C247 µF400 V
D2BAV21WS-
7-FD1DL4937
C622 µF25 V
C8100 pF50 V
C1610 pF50 V
C7100 nF25 V
C310 nF630 V
C12220 µF35 V
C10470 pF200 V
D4B340LB-13-F
D330BQ100PBF
C15470 pF200 V
C11220 µF35 V
C14820 µF6.3 V
T1EF25
C13820 µF6.3 V
C54.7 µF10 V
L2Ferrite Bead
(3.5 × 4.45 mm)
3
9,10
7,8
126
5 1
C1100 nF
310 VAC
RT15 Ω
F12 A tO
90 - 265VAC
18 V, 0.67 A
J2-6
5 V, 1A
J2-1
J1-3 J1-1
RTN
J2-4
LinkSwitch-HP
D
S
FB
BP
CPPD
CONTROLU1
LNK6774V
R846.4 kΩ
1%1/16 W
R623.2 kΩ
1%1/16 W
R7100 kΩ
5%1/16 W
R57.5 kΩ
5%1/8 W
R1010 Ω5%
1/8 W
R420 Ω5%
R3100 Ω5%
R2100 Ω5%
R13 kΩ R12
10 Ω5%
1/8 W
R1136 kΩ1/8 W
R910.5 kΩ
1%1/16 W
C4100 pF50 V
11
Design Examples
PI-7885-041316
C71000 pF630 V
C133 µF400 V
RT120 Ω
L116.6 mH
C1747 µF400 V
C233 µF400 V
C1847 µF400 V
C622 µF50 V
C81 µF25 V
C19150 pF
440 VAC
C11330 pF50 V
C21470 µF16 V
C2547 µF16 V
C141 µF50 V
C231 µF50 V
C2647 µF16 V
VR11N4738A-T
8.2 V
C12470 µF16 V
C92.2 µF25 V
L23.3 µH
L33.3 µH
FL3
32
41
2
FL1
FL2
T1RM8
NC
FL4
FL5
12 V, 1.25 A
TP3
5 V, 500 mA
TP4
RTN
TP5, TP6
R32.40 MΩ
1%
R42.40 MΩ
1%
R1215 Ω
R52.40 MΩ
1%R10
2.40 MΩ1%
R1347 Ω
1/10 W
D1DL4007
D2
DFL
R120
0-7
200
V
VR2
MM
SZ52
03B-
7-F
R92.7 kΩ1/10 W
R2822 Ω1/8 W
R8620 kΩ
11
10
D V
S IS
GN
D
SR/P
VO
FWD
FB
InnoSwitch-EP
CONTROL
R254.3 Ω
1/10 W
C241000 pF100 V
R144.3 Ω
1/10 W
C101000 pF100 V
R200.02 Ω
1%
R210.12 Ω
R1632.4 kΩ
1%1/16 W
R171 kΩ1%
1/8 W
R11360 kΩ
C151000 pF100 V
Q2AON7254
Q1AOTF2210L
R241 kΩ 1%
1/8 W
R1620 kΩ1/2 W
R18390 kΩ
1 W
R2620 kΩ1/2 W
R19390 kΩ
1 W
C201000 pF100 V
R151 MΩ1%
1/16 WR23
137 kΩ1%
1/16 W
BPPB
PS
U1INN2904K
BR1B10S-G1000 V
RV1625 VAC
F12 A
85 - 484VAC
LTP1
NTP2
InnoSwitch-EP – 2-Output, Isolated, Universal Input Flyback Power Supply with 900 V MOSFET (RDK-531)17.5 W, 12 V, 1.25 A and 5 V, 500 mA OUTPUTS, 85 – 484 VAC INPUT FLYBACK POWER SUPPLY
Worldwide Sales Support Locations
World Headquarters5245 Hellyer AvenueSan Jose, CA 95138, USAMain: +1 408-414-9200Customer Service Phone: +1-408-414-9665Fax: +1-408-414-9765Email: [email protected] [email protected]
On the Webwww.power.com
China (Shanghai)Rm 2410, Charity Plaza, No. 88North Caoxi RoadShanghai, PRC 200030Phone: +86-21-6354-6323Fax: +86-21-6354-6325e-mail: [email protected]
China (Shenzhen)17/F, HIVAC Building, No. 2, Keji Nan 8th Road, Nanshan District, Shenzhen, China, 518057Phone: +86-755-8672-8689Fax: +86-755-8672-8690e-mail: [email protected]
GermanyLindwurmstrasse 11480337 Munich, GermanyPhone: +49-895-527-39110Fax: +49-895-527-39200Email: [email protected]
India#1, 14th Main RoadVasanthanagarBangalore-560052, India Phone: +91-80-4113-8020Fax: +91-80-4113-8023Email: [email protected]
ItalyVia Milanese 20, 3rd. Fl., 20099 Sesto San Giovanni (MI), ItalyPhone: +39-024-550-8701Fax: +39-028-928-6009Email: [email protected]
JapanKosei Dai-3 Building2-12-11, Shin-Yokohama, Kohoku-ku,Yokohama-shi, Kanagawa 222-0033 JapanPhone: +81-45-471-1021Fax: +81-45-471-3717Email: [email protected]
KoreaRM 602, 6FLKorea City Air Terminal B/D, 159-6Samsung-Dong, Kangnam-GuSeoul, 135-728, KoreaPhone: +82-2-2016-6610Fax: +82-2-2016-6630Email: [email protected] Singapore 51 Newton Road#19-01/05 Goldhill PlazaSingapore, 308900Phone: +65-6358-2160Fax: +65-6358-2015Email: [email protected]
Taiwan5F, No. 318, Nei Hu Road, Sec. 1Taipei 11493, Taiwan R.O.C.Phone: +886-2-2659-4570Fax: +886-2-2659-4550Email: [email protected]
United KingdomCambridge Semiconductor,a Power Integrations companyWestbrook Centre, Block 5, 2nd FloorMilton RoadCambridge CB4 1YGPhone: +44 (0) 1223-446483e-mail: [email protected]
©2016 Power Integrations. Power Integrations, TOPSwitch, TinySwitch, LinkSwitch, LYTSwitch, InnoSwitch, DPA-Switch, PeakSwitch, CAPZero, SENZero, LinkZero, HiperPFS, HiperTFS, HiperLCS, Qspeed, EcoSmart, Clampless, E-Shield, Filterfuse, FluxLink, StakFET, PI Expert and PI FACTS and the Power Integrations logo are trademarks or registered trademarks of Power Integrations, Inc. All rights reserved.