Cat Electronic Technician 2020C v1.0 Product Status Report
4/15/2021 2:08 PM Product Status Report
Implement 300F
Logged Diagnostic Codes [Diagnostic Clock = 0 hours] - Implement 300F
Logged Event Codes [Diagnostic Clock = 0 hours] - Implement 300F
Active Diagnostic Codes - Implement 300F
Active Event Codes - Implement 300F
C4.4 312/314F (W7N20667)
Parameter ValueProduct ID DJE10115Equipment IDComments
Parameter ValueProduct IDEquipment ID UnavailableECM Part Number 4600132-05ECM Serial Number 0737F178VZSoftware Group Part Number 5258091-00Software Group Release Date Jan2017Software Group Description 300F HEX ATT CONTROL
Code Description Occ. First LastNo LoggedDiagnosticCodes
Code Description Occ. First LastNo LoggedEvent Codes
Code DescriptionNo ActiveDiagnosticCodes
Code DescriptionNo ActiveEvent Codes
Parameter ValueEquipment ID
Logged Diagnostic Codes [Diagnostic Clock = 2187 hours] - C4.4 312/314F (W7N20667)
Logged Event Codes [Diagnostic Clock = 2187 hours] - C4.4 312/314F (W7N20667)
Active Diagnostic Codes - C4.4 312/314F (W7N20667)
Active Event Codes - C4.4 312/314F (W7N20667)
System Communication Status - Active Problems - C4.4 312/314F (W7N20667)
System Communication Status - Inactive Problems - C4.4 312/314F (W7N20667)
Engine Serial Number W7N20667ECM Part Number 4620009-00ECM Serial Number 01077538VPSoftware Group Part Number 5944076-00Software Group Release Date MAY20Software Group Description 312_314F C4.4Calibration Identification Number AK439_23Operator Inducement Regulation Configuration Worldwide
Code Description Occ. First Last5856-14 SAE J1939 Data Link #3 : Special Instruction 1 2187 21875856- 9 SAE J1939 Data Link #3 : Abnormal Update Rate 17 2166 2186
Code Description Occ. First LastE931 (2) Low Aftertreatment #1 DEF Pressure #1 1 2155 2155E954 (1) Low Aftertreatment DEF Tank Level 2 2184 2185E954 (2) Low Aftertreatment DEF Tank Level 2 2184 2185E954 (3) Low Aftertreatment DEF Tank Level 2 2184 2185E1389 (1) Aftertreatment #1 SCR Operator Inducement 20 1938 2187E1389 (2) Aftertreatment #1 SCR Operator Inducement 3 2167 2185E1389 (3) Aftertreatment #1 SCR Operator Inducement 1 2167 2167
Code Description5856-14 SAE J1939 Data Link #3 : Special Instruction
Code DescriptionE1389 (1) Aftertreatment #1 SCR Operator Inducement
ECMs Detected Problem Data Link Diagnostic InformationDevice 1: C4.4312/314F (W7N20667)- Device 2:Aftertreatment #1 DEFTank Quality Sensor
Device #1 is notreceiving all expectedparameters fromDevice #2 on the datalink.
J1939 #3 Diagnostic Code: 5856-14 - Service HourMeter: 2187:26:38 -
ECMs Detected Problem Data Link Diagnostic InformationDevice 1: C4.4312/314F (W7N20667)- Device 2: MachineControl Module
Device #1 is unable tocommunicate withDevice #2 on the datalink.
J1939 #1 Diagnostic Code: 247-9 - Service Hour Meter:1820:21:06 -
Device 1: C4.4312/314F (W7N20667)- Device 2:Aftertreatment #1 DEFTank Quality Sensor
Device #1 is unable tocommunicate withDevice #2 on the datalink.
J1939 #3 Diagnostic Code: 5856-9 - Service Hour Meter:2186:53:21 -
Current Totals - C4.4 312/314F (W7N20667)
Configuration - C4.4 312/314F (W7N20667)
Description Value UnitTotal Idle Time 814:18 hoursTotal Fuel 4659 galTotal Engine #1 Fuel 4659 galTotal ARD Fuel 0.000 galTotal Idle Fuel 743 galTotal Max Fuel 11929 galAftertreatment #1 Total DEFUsed
78.9 gal
Engine Lifetime Hours 2186.5 hoursAverage Load Factor 35 %Engine Starts 3143Lifetime Total EngineRevolutions
176529992 rev
Total Operating Hours 2188 hoursOperator InducementEmergency Override TotalActivations
0
Operator InducementEmergency Override TotalResets
0
Total Engine Idle ShutdownCount
0
Total Engine Idle ShutdownOverrides Count
0
Total Delayed EngineShutdown Count
0
Total Delayed EngineShutdown Overrides Count
0
Starts/Hour 1.44Average RPM 1345.58 rpmPercentage Idle Time 37.23 %Average Fuel Rate 2.13 gal/hOverall Load Factor 39 %
Description Value UnitEquipment IDEngine Serial Number W7N20667ECM Serial Number 01077538VPSoftware Group Part Number 5944076-00Software Group Release Date MAY20Software Group Description 312_314F C4.4Ether Solenoid Configuration Not InstalledAftertreatment Ambient Air TemperatureSensor Installation Status
Not Installed
Engine Warm Up Elevated Idle FeatureEnable Status
Enabled
Engine Warm Up Elevated Idle Delay Time 10.0 min
Lifetime:Accumulated Time vs Intake Manifold Pressure - C4.4 312/314F (W7N20667)
Low System Battery Voltage Elevated Idle EnabledEngine Idle Shutdown Enable Status DisabledEngine Idle Shutdown Delay Time 5.0 minDelayed Engine Shutdown Enable Status DisabledDelayed Engine Shutdown Maximum Time 10.0 minEngine Fan Type Configuration Direct DriveEngine Cooling Fan Map UnavailableEngine Fan Purge Cycle Duration Unavailable secEngine Fan Purge Cycle Interval Unavailable secEngine Fan Suspend Purge UnavailableEngine Fan Manual Purge UnavailableFactory Installed Aftertreatment #1Identification Number
CGJ128439B
Operator Inducement ProgressConfiguration
Reduced Performance
Operator Inducement RegulationConfiguration
Worldwide
Operator Inducement Emergency OverrideEnable Status
Disabled
Operator Inducement Emergency OverrideActivation
Not Activated
Aftertreatment #1 DEF Tank Configuration CustomAftertreatment #1 DEF Quality SensorInstallation Status
Installed
System Operating Voltage Configuration 24 VoltFLS -2FTS -8CAN Communication Protocol WriteSecurity
Seed and Key Access
CAN Communication Protocol ReadSecurity
Seed and Key Access
Total Tattletale 4
Intake Manifold Pressure( psi ) hours %<11.603 31.10 22.3211.603-13.052 32.80 23.5413.053-14.503 44.30 31.7914.504-15.953 27.50 19.7315.954-17.404 3.60 2.5817.405-18.854 0.05 0.0418.855-20.304 0.00 0.0020.305-21.755 0.00 0.0021.756-23.205 0.00 0.0023.206-24.655 0.00 0.0024.656-26.106 0.00 0.0026.107-27.556 0.00 0.0027.557-29.007 0.00 0.0029.008-30.457 0.00 0.0030.458-31.907 0.00 0.00
Lifetime:Accumulated Time vs Engine Coolant Temperature - C4.4 312/314F (W7N20667)
31.908-33.358 0.00 0.0033.359-34.808 0.00 0.0034.809-36.258 0.00 0.0036.259-37.709 0.00 0.0037.710-39.159 0.00 0.0039.160-40.610 0.00 0.0040.611-42.060 0.00 0.0042.061-43.510 0.00 0.0043.511-44.961 0.00 0.0044.962-46.411 0.00 0.0046.412-47.861 0.00 0.0047.862-49.312 0.00 0.0049.313-50.762 0.00 0.0050.763-52.213 0.00 0.0052.214-53.663 0.00 0.0053.664-55.113 0.00 0.0055.114-56.564 0.00 0.0056.565-58.014 0.00 0.0058.015-59.464 0.00 0.0059.465-60.915 0.00 0.0060.916-62.365 0.00 0.0062.366-63.816 0.00 0.0063.817-65.266 0.00 0.0065.267-66.716 0.00 0.0066.717-68.167 0.00 0.0068.168-69.617 0.00 0.0069.618-71.067 0.00 0.0071.068-72.518 0.00 0.0072.519-73.968 0.00 0.0073.969-75.419 0.00 0.0075.420-76.869 0.00 0.0076.870-78.319 0.00 0.0078.320-79.770 0.00 0.0079.771-81.220 0.00 0.0081.221-82.670 0.00 0.0082.671-84.121 0.00 0.0084.122-85.571 0.00 0.0085.572-87.023 0.00 0.00>87.023 0.00 0.00
Engine Coolant Temperature(Deg F )
hours %
<32.00 0.30 0.0132.00-40.99 0.00 0.0041.00-49.99 0.05 0.0050.00-58.99 0.20 0.0159.00-67.99 1.00 0.05
Lifetime:Accumulated Occurrences vs Engine Speed - C4.4 312/314F (W7N20667)
Lifetime:Accumulated Time vs Engine Speed And Percent Engine Load at Current Engine Speed -C4.4 312/314F (W7N20667)
68.00-76.99 1.95 0.0977.00-85.99 3.40 0.1686.00-94.99 4.85 0.2395.00-103.99 6.90 0.32104.00-112.99 8.70 0.41113.00-121.99 10.80 0.51122.00-130.99 11.85 0.56131.00-139.99 14.95 0.70140.00-148.99 14.20 0.67149.00-157.99 17.95 0.84158.00-166.99 24.90 1.17167.00-175.99 1185.90 55.67176.00-184.99 628.55 29.50185.00-193.99 164.15 7.71194.00-202.99 28.20 1.32203.00-211.99 1.55 0.07212.00-220.99 0.00 0.00221.00-229.99 0.00 0.00230.00-238.99 0.00 0.00239.00-247.99 0.00 0.00248.00-256.99 0.00 0.00257.00-265.99 0.00 0.00266.00-274.99 0.00 0.00275.00-283.99 0.00 0.00284.00-292.99 0.00 0.00293.00-302.00 0.00 0.00>302.00 0.00 0.00
Engine Speed( rpm ) Count %<2600.0 0 0.002600.0-2699.9 0 0.002700.0-2799.9 0 0.002800.0-2899.9 0 0.002900.0-2999.9 0 0.003000.0-3099.9 0 0.003100.0-3199.9 0 0.003200.0-3299.9 0 0.003300.0-3400.0 0 0.00>3400.0 0 0.00
rpm <600.0 600.0-649.9
650.0-699.9
700.0-749.9
750.0-799.9
800.0-849.9
850.0-899.9
900.0-949.9
950.0-999.9
%<0.0 0.25 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.000.0-9.9 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
Lifetime:Accumulated Time vs Engine Speed And Percent Engine Load at Current Engine Speed -C4.4 312/314F (W7N20667)
Lifetime:Accumulated Time vs Engine Speed And Percent Engine Load at Current Engine Speed -C4.4 312/314F (W7N20667)
10.0-19.9
0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 16.85
20.0-29.9
0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.15 29.60
30.0-39.9
0.00 0.00 0.00 0.00 0.00 0.00 0.05 0.10 1.20
40.0-49.9
0.00 0.00 0.00 0.00 0.00 0.00 0.10 0.30 0.80
50.0-59.9
0.00 0.00 0.00 0.00 0.00 0.00 0.10 0.10 0.40
60.0-69.9
0.00 0.00 0.00 0.00 0.00 0.00 0.05 0.05 0.05
70.0-79.9
0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
80.0-89.9
0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
90.0-100.0
0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
>100.0 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00Total 0.25 0.00 0.00 0.00 0.00 0.00 0.30 0.70 48.90
rpm 1000.0-1049.9
1050.0-1099.9
1100.0-1149.9
1150.0-1199.9
1200.0-1249.9
1250.0-1299.9
1300.0-1349.9
1350.0-1399.9
1400.0-1449.9
%<0.0 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.000.0-9.9 0.00 0.05 0.45 0.50 0.45 0.45 0.55 0.55 0.7510.0-19.9
21.45 128.95 148.95 0.90 1.00 2.00 2.60 3.10 7.65
20.0-29.9
31.60 137.85 137.95 0.80 1.20 3.95 5.70 7.70 21.60
30.0-39.9
1.05 0.30 0.25 1.85 2.40 2.55 3.70 4.45 15.70
40.0-49.9
0.60 0.30 0.35 0.40 1.00 2.50 3.05 3.50 12.80
50.0-59.9
0.20 0.25 0.10 0.45 1.20 2.50 2.95 3.20 10.65
60.0-69.9
0.05 0.00 0.10 0.60 0.60 2.40 3.40 3.75 10.25
70.0-79.9
0.00 0.05 0.15 0.15 0.80 3.25 4.65 4.25 10.05
80.0-89.9
0.00 0.15 0.30 0.25 1.10 2.40 1.65 2.90 12.95
90.0-100.0
0.00 0.00 0.05 0.10 0.30 0.20 0.80 4.95 21.35
>100.0 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00Total 54.95 267.90 288.65 6.00 10.05 22.20 29.05 38.35 123.75
rpm 1450.0-1499.9
1500.0-1549.9
1550.0-1599.9
1600.0-1649.9
1650.0-1699.9
1700.0-1749.9
1750.0-1799.9
1800.0-1849.9
1850.0-1899.9
Lifetime:Accumulated Time vs Engine Speed And Percent Engine Load at Current Engine Speed -C4.4 312/314F (W7N20667)
%<0.0 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.000.0-9.9 2.00 3.15 2.40 0.85 0.20 0.00 0.00 0.00 0.0010.0-19.9
30.85 27.30 5.35 1.10 0.10 0.00 0.00 0.00 0.00
20.0-29.9
81.70 61.65 7.15 1.50 0.10 0.00 0.00 0.00 0.00
30.0-39.9
60.40 48.70 6.50 2.70 0.10 0.00 0.20 0.45 0.00
40.0-49.9
50.55 45.60 10.05 5.30 0.20 0.00 0.20 0.25 0.00
50.0-59.9
49.65 62.65 12.40 8.15 0.25 0.00 0.00 0.00 0.00
60.0-69.9
69.65 82.65 15.45 9.55 0.35 0.00 0.00 0.00 0.00
70.0-79.9
54.05 51.90 18.15 10.25 0.70 0.00 0.00 0.00 0.00
80.0-89.9
42.30 50.90 20.00 14.50 0.95 0.00 0.00 0.00 0.00
90.0-100.0
61.15 25.60 16.95 6.85 0.00 0.00 0.00 0.00 0.00
>100.0 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00Total 502.30 460.10 114.40 60.75 2.95 0.00 0.40 0.70 0.00
rpm 1900.0-1949.9
1950.0-1999.9
2000.0-2049.9
2050.0-2099.9
2100.0-2149.9
2150.0-2199.9
2200.0-2249.9
2250.0-2299.9
2300.0-2349.9
%<0.0 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.000.0-9.9 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.0010.0-19.9
0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
20.0-29.9
0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
30.0-39.9
0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
40.0-49.9
0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
50.0-59.9
0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
60.0-69.9
0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
70.0-79.9
0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
80.0-89.9
0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
90.0-100.0
0.00 0.10 0.00 0.00 0.00 0.00 0.00 0.00 0.00
>100.0 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00Total 0.00 0.10 0.00 0.00 0.00 0.00 0.00 0.00 0.00
Lifetime:Accumulated Time vs Engine Speed And Percent Engine Load at Current Engine Speed -C4.4 312/314F (W7N20667)
Lifetime:Accumulated Time vs Intake Manifold Air Temperature - C4.4 312/314F (W7N20667)
rpm 2350.0-2400.0 >2400.0 Total%<0.0 0.00 0.00 0.250.0-9.9 0.00 0.00 12.3510.0-19.9 0.00 0.00 398.1520.0-29.9 0.00 0.00 530.2030.0-39.9 0.00 0.00 152.6540.0-49.9 0.00 0.00 137.8550.0-59.9 0.00 0.00 155.2060.0-69.9 0.00 0.00 198.9570.0-79.9 0.00 0.00 158.4080.0-89.9 0.00 0.00 150.3590.0-100.0 0.00 0.00 138.40>100.0 0.00 0.00 0.00Total 0.00 0.00 2032.75
Intake Manifold AirTemperature( Deg F )
hours %
<32.00 0.45 0.0232.00-40.99 2.45 0.1241.00-49.99 11.95 0.5650.00-58.99 22.45 1.0559.00-67.99 51.80 2.4368.00-76.99 98.35 4.6277.00-85.99 179.05 8.4086.00-94.99 273.90 12.8695.00-103.99 333.70 15.66104.00-112.99 396.40 18.61113.00-121.99 384.05 18.03122.00-130.99 231.90 10.89131.00-139.99 114.75 5.39140.00-148.99 28.40 1.33149.00-157.99 0.75 0.04158.00-166.99 0.00 0.00167.00-175.99 0.00 0.00176.00-184.99 0.00 0.00185.00-193.99 0.00 0.00194.00-202.99 0.00 0.00203.00-211.99 0.00 0.00212.00-220.99 0.00 0.00221.00-229.99 0.00 0.00230.00-238.99 0.00 0.00239.00-248.00 0.00 0.00>248.00 0.00 0.00
Lifetime:Accumulated Time vs Engine Speed - C4.4 312/314F (W7N20667) Engine Speed( rpm ) hours %<550.0 0.30 0.01550.0-599.9 0.00 0.00600.0-649.9 0.00 0.00650.0-699.9 0.00 0.00700.0-749.9 0.00 0.00750.0-799.9 0.00 0.00800.0-849.9 0.05 0.00850.0-899.9 0.35 0.02900.0-949.9 0.90 0.04950.0-999.9 63.05 2.961000.0-1049.9 71.15 3.341050.0-1099.9 282.60 13.271100.0-1149.9 304.95 14.311150.0-1199.9 6.90 0.321200.0-1249.9 11.35 0.531250.0-1299.9 24.30 1.141300.0-1349.9 31.30 1.471350.0-1399.9 40.10 1.881400.0-1449.9 126.45 5.941450.0-1499.9 509.65 23.921500.0-1549.9 466.70 21.911550.0-1599.9 120.35 5.651600.0-1649.9 65.40 3.071650.0-1699.9 3.15 0.151700.0-1749.9 0.10 0.001750.0-1799.9 0.40 0.021800.0-1849.9 0.70 0.031850.0-1899.9 0.00 0.001900.0-1949.9 0.00 0.001950.0-1999.9 0.10 0.002000.0-2049.9 0.05 0.002050.0-2099.9 0.00 0.002100.0-2149.9 0.00 0.002150.0-2199.9 0.00 0.002200.0-2249.9 0.00 0.002250.0-2299.9 0.00 0.002300.0-2349.9 0.00 0.002350.0-2399.9 0.00 0.002400.0-2449.9 0.00 0.002450.0-2499.9 0.00 0.002500.0-2549.9 0.00 0.002550.0-2599.9 0.00 0.002600.0-2649.9 0.00 0.002650.0-2699.9 0.00 0.002700.0-2749.9 0.00 0.00
Lifetime:Accumulated Time vs Air Inlet Temperature - C4.4 312/314F (W7N20667)
Monitoring System - C4.4 312/314F (W7N20667)
2750.0-2799.9 0.00 0.002800.0-2849.9 0.00 0.002850.0-2899.9 0.00 0.002900.0-2949.9 0.00 0.002950.0-2999.9 0.00 0.003000.0-3049.9 0.00 0.003050.0-3099.9 0.00 0.003100.0-3149.9 0.00 0.003150.0-3199.9 0.00 0.003200.0-3249.9 0.00 0.003250.0-3299.9 0.00 0.003300.0-3349.9 0.00 0.003350.0-3400.0 0.00 0.00>3400.0 0.00 0.00
Air Inlet Temperature( Deg F ) hours %<(-4.00) 0.30 0.01(-4.00)-4.99 0.00 0.005.00-13.99 0.00 0.0014.00-22.99 0.00 0.0023.00-31.99 1.40 0.0732.00-40.99 18.30 0.8641.00-49.99 96.60 4.5350.00-58.99 147.70 6.9359.00-67.99 228.40 10.7268.00-76.99 336.75 15.8177.00-85.99 407.85 19.1586.00-94.99 452.85 21.2695.00-103.99 326.15 15.31104.00-112.99 111.30 5.22113.00-121.99 2.60 0.12122.00-130.99 0.00 0.00131.00-139.99 0.00 0.00140.00-148.99 0.00 0.00149.00-157.99 0.00 0.00158.00-166.99 0.00 0.00167.00-176.00 0.00 0.00>176.00 0.00 0.00
Description State Trip Point Delay TimeEngine OverspeedLeast Severe (1) Always On 3000 rpm 0 secHigh Air Inlet #1Differential PressureLeast Severe (1) Always On 0.9 psi 0 secModerate Severity (2) Always On 0.9 psi 0 sec
Injector Codes Calibration - C4.4 312/314F (W7N20667)
Aftertreatment Abnormal Shutdown History - C4.4 312/314F (W7N20667)
Diesel Exhaust Fluid Controller #1
Configuration - Diesel Exhaust Fluid Controller #1
High Engine CoolantTemperatureLeast Severe (1) Always On 228 Deg F 10 secModerate Severity (2) Always On 232 Deg F 10 secMost Severe (3) Always On 237 Deg F 10 secHigh ExhaustTemperatureLeast Severe (1) Always On 388 Deg F 8 secModerate Severity (2) Always On 392 Deg F 8 secHigh Fuel/WaterSeparator Water LevelLeast Severe (1) Always On None 5 secModerate Severity (2) Always On None 1800 secHigh Intake ManifoldAir TemperatureLeast Severe (1) Always On 253.4 Deg F 8 secModerate Severity (2) Always On 257.0 Deg F 8 secLow Engine OilPressureLeast Severe (1) Always On None 0 secMost Severe (3) Always On None 0 sec
Injector CodeInjector 1 79F9FD000317451AF808250000FFABInjector 2 79EFF4E8F01361F5EA004A0000FFB0Injector 3 79EBF6EDEE033108E0FB250000FF24Injector 4 79F5FBF6F8031719F305230000FF57
History DataNo history data available.
Parameter ValueAftertreatment #1 DEF Dosing System SerialNumber
1707423324
ECU Serial Number 30313137303430323532Software Group Part Number 4815824-00Software Group Release Date AUG2015
Description Value UnitAftertreatment #1 DEF Dosing SystemSerial Number
1707423324
ECU Serial Number 30313137303430323532Software Group Part Number 4815824-00Software Group Release Date AUG2015System Operating Voltage Configuration 24 Volt
Machine Control 312E/F (DJE10115)
Logged Diagnostic Codes [Diagnostic Clock = 2187 hours] - Machine Control 312E/F (DJE10115)
Logged Event Codes [Diagnostic Clock = 2187 hours] - Machine Control 312E/F (DJE10115)
Active Diagnostic Codes - Machine Control 312E/F (DJE10115)
Active Event Codes - Machine Control 312E/F (DJE10115)
Current Totals - Machine Control 312E/F (DJE10115)
Parameter ValueProduct ID DJE10115ECM Part Number 4600132-05ECM Serial Number 0737F213VZSoftware Group Part Number 5403985-00Software Group Release Date Jul2017Software Group Description 312F HEX CONTROL
Code Description Occ. First Last1956- 3 Bucket Cylinder Position Sensor : Voltage Above
Normal2 2186 2187
586-12 Engine Speed Dial Switch : Failure 15 2185 2185
Code Description Occ. First LastNo LoggedEvent Codes
Code DescriptionNo ActiveDiagnosticCodes
Code DescriptionNo ActiveEvent Codes
Description Value UnitTotal Operating Hours 2188 hoursEngine Maintenance Hours 2187 hoursEngine Oil Hours 274 hoursEngine Oil Filter Hours 274 hoursEngine Coolant Hours 2187 hoursFuel/ Water Separator Hours 274 hoursSecondary Fuel Filter Hours 274 hoursFuel Pump Screen Filter Hours 2187 hoursFuel Tank Cap Hours 839 hoursCrankcase Ventilation FilterHours
544 hours
Hydraulic Pump Hours 2187 hoursHydraulic Pilot Oil Filter Hours 839 hoursHydraulic Case Drain Oil FilterHours
839 hours
Return Hydraulic Oil FilterHours
2187 hours
Configuration - Machine Control 312E/F (DJE10115)
Aftertreatment DEF Filter Hours 544 hoursHydraulic Oil Hours 2187 hoursFinal Drive Oil Hours 2187 hoursSwing Motor Hours 682 hoursSwing Drive Oil Hours 839 hoursTravel Motor Hours 197 hoursTool #1 Hours 2 hoursTool #2 Hours 19 hoursTool #3 Hours 163 hoursTool #4 Hours 0 hoursTool #5 Hours 2 hoursTool #6 Hours 5 hoursTool #7 Hours 0 hoursTool #8 Hours 0 hoursTool #9 Hours 19 hoursTool #10 Hours 0 hoursReturn Hydraulic Oil FilterBypass Hours
69.8 hours
Return Hydraulic Oil FilterBypass at Cold TemperatureHours
22.1 hours
Hours of Operation at HighHydraulic Pressure
17.9 hours
Hours of Operation at ReliefHydraulic Pressure
0.6 hours
Description Value UnitProduct ID DJE10115Hydraulic Power Mode HighHydraulic Power High Mode SelectionDisplay Enable Status
Enabled
Hydraulic Power Standard Mode SelectionDisplay Enable Status
Disabled
On Demand Engine Power Enable Status DisabledLighting Shutdown Timer Duration 1 minTravel Alarm Installation Status InstalledQuick Coupler Installation Status Installed without Coupler AcceleratorQuick Coupler Constant EngagementPressure System Installation Status
Installed
Fine Swing System Installation Status InstalledSmart Boom Installation Status Not InstalledBoom Low Pressure Relief SystemInstallation Status
Not Installed
Attachment Hydraulic Oil Filter SwitchConfiguration
Not Installed
Machine Overload Pressure SensorInstallation
Not Installed
Fuel Tank Maximum Volume 57 galEngine Speed Management FeatureInstallation Status
Not Installed
Heavy Lift System Installation Status Not InstalledBlade Installation Status Not InstalledMachine Lockout System InstallationStatus
Not Installed
Monitoring System Configuration Code 0Implement Pump Configuration Code UnavailableMachine Application Configuration Multi-Proc - ElectricalAttachment Valve #1 Configuration One Way or Two Way - Pump #1Attachment Valve #2 Configuration One Way or Two Way - Pump #2Attachment Valve #3 Configuration Attachment Pump Valve - Two WayAttachment Valve #4 Configuration Not InstalledAttachment Valve #1 Control TypeConfiguration
Electrical
Attachment Valve #2 Control TypeConfiguration
Electrical
Attachment Valve #3 Control TypeConfiguration
Electrical
Attachment Valve #1 CombinerConfiguration
Valve #2 Combined with Valve #1
Variable Relief Valve #1 Configuration Installed on Valve #1 Extend portVariable Relief Valve #2 Configuration Installed on Valve #1 Retract portF2 Type Valve Load Sense Pres SensorInstallation
Not Installed
Tool Program Main Pump Flow LimitFunction Enable Status
Enabled
Boom Cylinder Retract Speed Limit SystemInstallation Status
Not Installed
Stick Cylinder Extend Speed Limit SystemInstallation Status
Not Installed
Stick Cylinder Retract Speed Limit SystemInstallation Status
Not Installed
Enhanced Multiple Operation AttachmentValve Limit Installation Status
Installed
Attachment Pedal #1 Pilot Pressure SensorInstallation Status
Not Installed
Attachment Pedal #2 Pilot Pressure SensorInstallation Status
Not Installed
Hammer Automatic Control FeatureInstallation Status
Not Installed
Joystick Handle Configuration Modulation HandleFoot Switch Installation Status Not InstalledLeft Attachment Pedal Installation Status InstalledRight Attachment Pedal Installation Status Not InstalledLeft Joystick Switch #1 Control Mode No valve controlledLeft Joystick Switch #2 Control Mode No valve controlledRight Joystick Switch #1 Control Mode Momentary - Valve #1 ExtendRight Joystick Switch #2 Control Mode No valve controlledLeft Joystick Thumbwheel Control Mode Attachment Valve #3Right Joystick Thumbwheel Control Mode Attachment Valve #1Left Attachment Pedal Forward ControlMode
Attachment Valve #1 Extend
Left Attachment Pedal Rearward ControlMode
Attachment Valve #1 Retract
Travel Speed Shift Low Delay 0.4 secTravel Speed Shift High Delay 0.4 secTravel Speed Shift Low Pres 2611 psiTravel Speed Shift High Pressure 4641 psiOne Touch Engine Speed Setting 1100 rpmAESC Setting 1100 rpmAESC Delay Time 5.0 secThrottle Dial Position 1 Engine Speed 1000 rpmThrottle Dial Position 2 Engine Speed 1100 rpmThrottle Dial Position 3 Engine Speed 1200 rpmThrottle Dial Position 4 Engine Speed 1250 rpmThrottle Dial Position 5 Engine Speed 1280 rpmThrottle Dial Position 6 Engine Speed 1320 rpmThrottle Dial Position 7 Engine Speed 1350 rpmThrottle Dial Position 8 Engine Speed 1400 rpmThrottle Dial Position 9 Engine Speed 1450 rpmThrottle Dial Position 10 Engine Speed 1500 rpmThrottle Dial Position 1 Hydraulic SystemTorque Percentage
20.0 %
Throttle Dial Position 2 Hydraulic SystemTorque Percentage
48.0 %
Throttle Dial Position 3 Hydraulic SystemTorque Percentage
62.0 %
Throttle Dial Position 4 Hydraulic SystemTorque Percentage
75.0 %
Throttle Dial Position 5 Hydraulic SystemTorque Percentage
84.0 %
Throttle Dial Position 6 Hydraulic SystemTorque Percentage
84.0 %
Throttle Dial Position 7 Hydraulic SystemTorque Percentage
84.0 %
Throttle Dial Position 8 Hydraulic SystemTorque Percentage
84.0 %
Throttle Dial Position 9 Hydraulic SystemTorque Percentage
90.0 %
Throttle Dial Position 10 Hydraulic SystemTorque Percentage
100.0 %
Engine Oil Recommended MaintenanceInterval
500 hours
Engine Oil Filter RecommendedMaintenance Interval
500 hours
Engine Coolant RecommendedMaintenance Interval
6000 hours
Fuel/ Water Separator RecommendedMaint Interval
500 hours
Secondary Fuel Filter RecommendedMaintenance Interval
500 hours
Fuel Pump Screen Filter RecommendedMaintenance Interval
3000 hours
Tertiary Fuel Filter RecommendedMaintenance Interval
0 hours
Fuel Tank Cap RecommendedMaintenance Interval
1000 hours
Crankcase Ventilation Filter RecommendedMaintenance Interval
1500 hours
Aftertreatment Spark Plug RecommendedMaintenance Interval
0 hours
Hydraulic Pilot Oil Filter RecommendedMaintenance Interval
1000 hours
Hydraulic Case Drain Oil FilterRecommended MI
1000 hours
Return Hyd Oil Filter Recommended MaintInterval
2000 hours
Attachment Hydraulic Oil FilterRecommended Maintenance Interval
0 hours
Aftertreatment DEF Filter RecommendedMaintenance Interval
1500 hours
Final Drive Oil RecommendedMaintenance Interval
2000 hours
Hydraulic Oil Recommended MaintenanceInterval
6000 hours
Swing Drive Oil RecommendedMaintenance Interval
1000 hours
Crane System Installation Status Not InstalledUndercarriage Length Configuration StandardExcavator Stick Configuration MediumMaximum Work Tool Width 0 mmGrade Control System Installation Status InstalledStick Maximum Extension Angle 27.90 DegStick Minimum Retraction Angle 152.00 DegBoom Maximum Extension Angle 67.80 DegBoom Minimum Retraction Angle -44.80 DegBucket Cylinder Maximum ExtensionLength
2331.0 mm
Bucket Cylinder Minimum RetractionLength
1392.0 mm
Boom to Center of Rotation Lateral Offset 140 mmBoom to Center of Rotation Reach Offset 120 mmGrade Control Switch Installation Status InstalledMachine Laser Sensor Installation Status InstalledDirectional Heading Sensor InstallationStatus
Not Installed
Grade Control System Light Bar InstallationStatus
Not Installed
Work Tool Elevation Focus Point CenterElevation On-Grade Tolerance 25 mmGrade Control Above Grade Audible AlarmConfiguration
Off
Grade Control On Grade Audible AlarmConfiguration
Off
Calibration Status - Machine Control 312E/F (DJE10115)
Grade Control Below Grade Audible AlarmConfiguration
Off
Grade Slope Units Configuration DegreesLinkage Ceiling Violation Warning EnableStatus
Disabled
Linkage Floor Violation Warning EnableStatus
Disabled
Boom Calibration Angle Value #1 Status UsedBoom Calibration Angle Value #1 -76.57 DegBoom Calibration Angle Value #2 Status UsedBoom Calibration Angle Value #2 -76.51 DegBoom Calibration Angle Value #3 Status UsedBoom Calibration Angle Value #3 -76.54 DegBoom Calibration Angle Value #4 Status Not UsedBoom Calibration Angle Value #4 0.00 DegBoom Calibration Angle Value #5 Status Not UsedBoom Calibration Angle Value #5 0.00 DegStick Calibration Angle Value #1 Status UsedStick Calibration Angle Value #1 -3.30 DegStick Calibration Angle Value #2 Status UsedStick Calibration Angle Value #2 -3.80 DegStick Calibration Angle Value #3 Status UsedStick Calibration Angle Value #3 -3.14 DegStick Calibration Angle Value #4 Status Not UsedStick Calibration Angle Value #4 0.00 DegStick Calibration Angle Value #5 Status Not UsedStick Calibration Angle Value #5 0.00 DegBucket Cylinder Calibration Length Value#1 Status
Used
Bucket Cylinder Calibration Length Value#2 Status
Not Used
Bucket Cylinder Calibration Length Value#3 Status
Not Used
Bucket Cylinder Calibration Length Value#4 Status
Not Used
Bucket Cylinder Calibration Length Value#5 Status
Not Used
Advanced Machine Security SystemInstallation Status
Not Installed
Total Tattletale Unavailable
Calibration Status Last Successful CompletionPRV - Variable Relief PressureCalibration Solenoid 2
Success 1.5 hours
PRV - Variable Relief PressureCalibration Solenoid 1
Success 1.4 hours
Tilt Bucket Angle SensorCalibration
Not Calibrated Never Successfully Calibrated
Stick Angle Calibration Success 3.3 hours
Boom Offset Left Pilot PressureLimit Solenoid Cal
Not Calibrated Never Successfully Calibrated
Boom Offset Right PilotPressure Limit Solenoid Cal
Not Calibrated Never Successfully Calibrated
Stick Cylinder Extend PilotPressure Limit Solenoid Cal
Not Calibrated Never Successfully Calibrated
Stick Cylinder Retract PilotPressure Limit Solenoid Cal
Not Calibrated Never Successfully Calibrated
Boom Cylinder Retract LimitSolenoid Calibration
Not Calibrated Never Successfully Calibrated
Boom Cylinder Extend PilotPressure Limit Solenoid Cal
Not Calibrated Never Successfully Calibrated
PRV - Power Shift PressureCalibration
Success 1.3 hours
Pump #2 Flow LimitationPressure Solenoid Calibration -Flow
Success 1.4 hours
Pump #1 Flow LimitationPressure Solenoid Calibration -Flow
Success 1.3 hours
Pump #2 Flow LimitationPressure Solenoid Calibration -Pres
Not Calibrated Never Successfully Calibrated
Pump #1 Flow LimitationPressure Solenoid Calibration -Pres
Failed 1.3 hours
Error: 0006 Aborted by user Error: 0009 Aborted by ECM
Grade Control Bucket MeasureUp Calibration
Unknown Never Successfully Calibrated
Right Attachment PedalCalibration
Not Calibrated Never Successfully Calibrated
Left Attachment PedalCalibration
Success 1.2 hours
Right Joystick ThumbwheelCalibration
Success 1.2 hours
Left Joystick ThumbwheelCalibration
Success 1.2 hours
Hoe Bucket Angle Calibration Not Calibrated Never Successfully CalibratedDirectional Heading SensorCalibration
Not Calibrated Never Successfully Calibrated
Chassis Angle SensorCalibration
Success 3.1 hours
Bypass Cutoff Valve #2Pressure Solenoid Calibration
Not Calibrated Never Successfully Calibrated
Bypass Cutoff Valve #1Pressure Solenoid Calibration
Not Calibrated Never Successfully Calibrated
Boom and Stick Angle SensorCalibration
Success 3.2 hours
Boom Down RegenerationValve Pressure Calibration
Success 1.3 hours
Boom Angle Calibration Success 3.3 hoursAttachment Valve #4 Retract Not Calibrated Never Successfully CalibratedAttachment Valve #4 Extend Not Calibrated Never Successfully Calibrated
Job:Accumulated Time vs Hydraulic Oil Temperature - Machine Control 312E/F (DJE10115)
Job:Accumulated Time vs Main Hydraulic Pump Oil Pressure - Machine Control 312E/F(DJE10115)
Tool Configuration - Machine Control 312E/F (DJE10115) Active Tool : None
Attachment Valve #3 Retract Success 1.4 hoursAttachment Valve #3 Extend Success 1.4 hoursAttachment Valve #2 Retract Success 1.4 hoursAttachment Valve #2 Extend Success 1.4 hoursAttachment Valve #1 Retract Success 1.4 hoursAttachment Valve #1 Extend Success 1.4 hours
Hydraulic Oil Temperature( DegF )
hours %
<68.0 70.00 3.2068.0-85.9 154.15 7.0586.0-103.9 372.25 17.02104.0-121.9 561.00 25.64122.0-139.9 653.40 29.87140.0-157.9 250.90 11.47158.0-175.9 96.15 4.40176.0-193.9 29.75 1.36194.0-211.9 0.10 0.00212.0-229.9 0.00 0.00230.0-248.0 0.00 0.00>248.0 0.00 0.00
Main Hydraulic Pump OilPressure( psi )
hours %
<2900.8 2109.20 96.412900.8-3190.7 31.20 1.433190.8-3480.8 15.75 0.723480.9-3770.9 10.90 0.503771.0-4061.0 7.80 0.364061.1-4351.0 8.20 0.374351.1-4641.1 4.35 0.204641.2-4931.2 0.30 0.014931.3-5221.3 0.05 0.005221.4-5511.3 0.00 0.005511.4-5801.5 0.00 0.00>5801.5 0.00 0.00
Description Value UnitTool Program Name H90CSTool Program Tool Type HammerMaximum Throttle Dial 10Minimum Throttle Dial Position 1
Fuel Economy Mode EnableStatus
Enabled
Tool Program Pump FlowControl Mode
Pump #2
Initial Tool Program MediumPressure Circuit Main PumpTorque Reduction
0 %
Total Tool Program MediumPressure Circuit Main PumpTorque Reduction
30 %
Variable Relief Valve #1Pressure
3046 psi
Variable Relief Valve #2Pressure
0 psi
Enhanced Multiple OperationAttachment Valve Limit EnableStatus
Disabled
Single Pump Mode MaximumExtend Pilot Pressure forAttachment Valve
580 psi
Single Pump Mode MaximumRetract Pilot Pressure forAttachment Valve
580 psi
Boom Down RegenerationValve Maximum Pilot Pressure
580 psi
Tool Program HydraulicTemperature High WarningEvent Threshold
176.0 Deg F
Attachment Valve #1 FlowSetting
36 gal/min
Attachment Valve #1 Multi-Operation Additional Flow
0 gal/min
Tool Program Attachment Valve#1 One Way/ Two Way ValveMode
One Way
Attachment Valve #1 MaximumExtend Pressure
580 psi
Multiple Operation MaximumExtend Pilot Pressure forAttachment Valve #1
580 psi
Attachment Valve #1 OpenTime
0.20 sec
Attachment Valve #1 CloseTime
0.20 sec
Attachment Valve #3 MaximumExtend Pressure
290 psi
Attachment Valve #3 MaximumRetract Pressure
290 psi
Attachment Valve #3 OpenTime
0.20 sec
Attachment Valve #3 CloseTime
0.20 sec
Attachment Valve #3 Tool FlowDirection
Normal
Description Value UnitTool Program Name H100STool Program Tool Type HammerMaximum Throttle Dial 10Minimum Throttle Dial Position 1Fuel Economy Mode EnableStatus
Enabled
Tool Program Pump FlowControl Mode
Combined Flow
Initial Tool Program MediumPressure Circuit Main PumpTorque Reduction
0 %
Total Tool Program MediumPressure Circuit Main PumpTorque Reduction
30 %
Variable Relief Valve #1Pressure
3046 psi
Variable Relief Valve #2Pressure
0 psi
Enhanced Multiple OperationAttachment Valve Limit EnableStatus
Disabled
Single Pump Mode MaximumExtend Pilot Pressure forAttachment Valve
580 psi
Single Pump Mode MaximumRetract Pilot Pressure forAttachment Valve
580 psi
Boom Down RegenerationValve Maximum Pilot Pressure
580 psi
Tool Program HydraulicTemperature High WarningEvent Threshold
176.0 Deg F
Attachment Valve #1 FlowSetting
28 gal/min
Attachment Valve #1 Multi-Operation Additional Flow
0 gal/min
Tool Program Attachment Valve#1 One Way/ Two Way ValveMode
One Way
Attachment Valve #1 MaximumExtend Pressure
580 psi
Multiple Operation MaximumExtend Pilot Pressure forAttachment Valve #1
580 psi
Attachment Valve #1 OpenTime
0.20 sec
Attachment Valve #1 CloseTime
0.20 sec
Attachment Valve #2 MaximumExtend Pressure
580 psi
Multiple Operation MaximumExtend Pilot Pressure forAttachment Valve #2
580 psi
Attachment Valve #2 OpenTime
0.20 sec
Attachment Valve #2 CloseTime
0.20 sec
Attachment Valve #3 MaximumExtend Pressure
290 psi
Attachment Valve #3 MaximumRetract Pressure
290 psi
Attachment Valve #3 OpenTime
0.20 sec
Attachment Valve #3 CloseTime
0.20 sec
Attachment Valve #3 Tool FlowDirection
Normal
Description Value UnitTool Program Name H115STool Program Tool Type HammerMaximum Throttle Dial 10Minimum Throttle Dial Position 1Fuel Economy Mode EnableStatus
Enabled
Tool Program Pump FlowControl Mode
Combined Flow
Initial Tool Program MediumPressure Circuit Main PumpTorque Reduction
0 %
Total Tool Program MediumPressure Circuit Main PumpTorque Reduction
30 %
Variable Relief Valve #1Pressure
3046 psi
Variable Relief Valve #2Pressure
0 psi
Enhanced Multiple OperationAttachment Valve Limit EnableStatus
Disabled
Single Pump Mode MaximumExtend Pilot Pressure forAttachment Valve
580 psi
Single Pump Mode MaximumRetract Pilot Pressure forAttachment Valve
580 psi
Boom Down RegenerationValve Maximum Pilot Pressure
580 psi
Tool Program HydraulicTemperature High WarningEvent Threshold
176.0 Deg F
Attachment Valve #1 FlowSetting
30 gal/min
Attachment Valve #1 Multi-Operation Additional Flow
0 gal/min
Tool Program Attachment Valve#1 One Way/ Two Way ValveMode
One Way
Attachment Valve #1 MaximumExtend Pressure
580 psi
Multiple Operation MaximumExtend Pilot Pressure forAttachment Valve #1
580 psi
Attachment Valve #1 OpenTime
0.20 sec
Attachment Valve #1 CloseTime
0.20 sec
Attachment Valve #2 MaximumExtend Pressure
580 psi
Multiple Operation MaximumExtend Pilot Pressure forAttachment Valve #2
580 psi
Attachment Valve #2 OpenTime
0.20 sec
Attachment Valve #2 CloseTime
0.20 sec
Attachment Valve #3 MaximumExtend Pressure
290 psi
Attachment Valve #3 MaximumRetract Pressure
290 psi
Attachment Valve #3 OpenTime
0.20 sec
Attachment Valve #3 CloseTime
0.20 sec
Attachment Valve #3 Tool FlowDirection
Normal
Description Value UnitTool Program Name MP15/P315Tool Program Tool Type ShearMaximum Throttle Dial 10Minimum Throttle Dial Position 1Fuel Economy Mode EnableStatus
Enabled
Tool Program Pump FlowControl Mode
Combined Flow
Initial Tool Program MediumPressure Circuit Main PumpTorque Reduction
0 %
Total Tool Program MediumPressure Circuit Main PumpTorque Reduction
30 %
Variable Relief Valve #1Pressure
5802 psi
Variable Relief Valve #2Pressure
5802 psi
Enhanced Multiple OperationAttachment Valve Limit EnableStatus
Disabled
Single Pump Mode MaximumExtend Pilot Pressure forAttachment Valve
580 psi
Single Pump Mode MaximumRetract Pilot Pressure forAttachment Valve
580 psi
Boom Down RegenerationValve Maximum Pilot Pressure
580 psi
Tool Program HydraulicTemperature High WarningEvent Threshold
258.8 Deg F
Attachment Valve #1 FlowSetting
40 gal/min
Attachment Valve #1 Multi-Operation Additional Flow
13 gal/min
Tool Program Attachment Valve#1 One Way/ Two Way ValveMode
Two Way
Attachment Valve #1 MaximumExtend Pressure
580 psi
Attachment Valve #1 MaximumRetract Pressure
580 psi
Multiple Operation MaximumExtend Pilot Pressure forAttachment Valve #1
160 psi
Multiple Operation MaximumRetract Pilot Pressure forAttachment Valve #1
160 psi
Attachment Valve #1 OpenTime
0.20 sec
Attachment Valve #1 CloseTime
0.20 sec
Attachment Valve #1 Tool FlowDirection
Normal
Attachment Valve #2 MaximumExtend Pressure
580 psi
Attachment Valve #2 MaximumRetract Pressure
580 psi
Multiple Operation MaximumExtend Pilot Pressure forAttachment Valve #2
160 psi
Multiple Operation MaximumRetract Pilot Pressure forAttachment Valve #2
160 psi
Attachment Valve #2 OpenTime
0.20 sec
Attachment Valve #2 CloseTime
0.20 sec
Attachment Valve #3 MaximumExtend Pressure
290 psi
Attachment Valve #3 MaximumRetract Pressure
290 psi
Attachment Valve #3 OpenTime
0.20 sec
Attachment Valve #3 CloseTime
0.20 sec
Attachment Valve #3 Tool FlowDirection
Normal
Description Value UnitTool Program Name S320BTool Program Tool Type ShearMaximum Throttle Dial 10Minimum Throttle Dial Position 1Fuel Economy Mode EnableStatus
Enabled
Tool Program Pump FlowControl Mode
Combined Flow
Initial Tool Program MediumPressure Circuit Main PumpTorque Reduction
0 %
Total Tool Program MediumPressure Circuit Main PumpTorque Reduction
30 %
Variable Relief Valve #1Pressure
5802 psi
Variable Relief Valve #2Pressure
5802 psi
Enhanced Multiple OperationAttachment Valve Limit EnableStatus
Disabled
Single Pump Mode MaximumExtend Pilot Pressure forAttachment Valve
580 psi
Single Pump Mode MaximumRetract Pilot Pressure forAttachment Valve
580 psi
Boom Down RegenerationValve Maximum Pilot Pressure
580 psi
Tool Program HydraulicTemperature High WarningEvent Threshold
258.8 Deg F
Attachment Valve #1 FlowSetting
40 gal/min
Attachment Valve #1 Multi-Operation Additional Flow
13 gal/min
Tool Program Attachment Valve#1 One Way/ Two Way ValveMode
Two Way
Attachment Valve #1 MaximumExtend Pressure
580 psi
Attachment Valve #1 MaximumRetract Pressure
580 psi
Multiple Operation MaximumExtend Pilot Pressure forAttachment Valve #1
160 psi
Multiple Operation MaximumRetract Pilot Pressure forAttachment Valve #1
160 psi
Attachment Valve #1 OpenTime
0.20 sec
Attachment Valve #1 CloseTime
0.20 sec
Attachment Valve #1 Tool FlowDirection
Normal
Attachment Valve #2 MaximumExtend Pressure
580 psi
Attachment Valve #2 MaximumRetract Pressure
580 psi
Multiple Operation MaximumExtend Pilot Pressure forAttachment Valve #2
160 psi
Multiple Operation MaximumRetract Pilot Pressure forAttachment Valve #2
160 psi
Attachment Valve #2 OpenTime
0.20 sec
Attachment Valve #2 CloseTime
0.20 sec
Attachment Valve #3 MaximumExtend Pressure
290 psi
Attachment Valve #3 MaximumRetract Pressure
290 psi
Attachment Valve #3 OpenTime
0.20 sec
Attachment Valve #3 CloseTime
0.20 sec
Attachment Valve #3 Tool FlowDirection
Normal
Description Value UnitTool Program Name G310BTool Program Tool Type GrappleMaximum Throttle Dial 10Minimum Throttle Dial Position 1Fuel Economy Mode EnableStatus
Enabled
Tool Program Pump FlowControl Mode
Pump #2
Initial Tool Program MediumPressure Circuit Main PumpTorque Reduction
0 %
Total Tool Program MediumPressure Circuit Main PumpTorque Reduction
30 %
Variable Relief Valve #1Pressure
5802 psi
Variable Relief Valve #2Pressure
5802 psi
Enhanced Multiple OperationAttachment Valve Limit EnableStatus
Disabled
Single Pump Mode MaximumExtend Pilot Pressure forAttachment Valve
580 psi
Single Pump Mode MaximumRetract Pilot Pressure forAttachment Valve
580 psi
Boom Down RegenerationValve Maximum Pilot Pressure
580 psi
Tool Program HydraulicTemperature High WarningEvent Threshold
258.8 Deg F
Attachment Valve #1 FlowSetting
16 gal/min
Attachment Valve #1 Multi-Operation Additional Flow
0 gal/min
Tool Program Attachment Valve#1 One Way/ Two Way ValveMode
Two Way
Attachment Valve #1 MaximumExtend Pressure
580 psi
Attachment Valve #1 MaximumRetract Pressure
580 psi
Multiple Operation MaximumExtend Pilot Pressure forAttachment Valve #1
580 psi
Multiple Operation MaximumRetract Pilot Pressure forAttachment Valve #1
580 psi
Attachment Valve #1 OpenTime
0.20 sec
Attachment Valve #1 CloseTime
0.20 sec
Attachment Valve #1 Tool FlowDirection
Normal
Attachment Valve #3 MaximumExtend Pressure
290 psi
Attachment Valve #3 MaximumRetract Pressure
290 psi
Attachment Valve #3 OpenTime
0.20 sec
Attachment Valve #3 CloseTime
0.20 sec
Attachment Valve #3 Tool FlowDirection
Normal
Description Value UnitTool Program Name NGTTool Program Tool Type Tilt BucketMaximum Throttle Dial 10Minimum Throttle Dial Position 1
Fuel Economy Mode EnableStatus
Enabled
Tool Program Pump FlowControl Mode
Pump #2
Initial Tool Program MediumPressure Circuit Main PumpTorque Reduction
0 %
Total Tool Program MediumPressure Circuit Main PumpTorque Reduction
30 %
Variable Relief Valve #1Pressure
4061 psi
Variable Relief Valve #2Pressure
4061 psi
Enhanced Multiple OperationAttachment Valve Limit EnableStatus
Disabled
Single Pump Mode MaximumExtend Pilot Pressure forAttachment Valve
580 psi
Single Pump Mode MaximumRetract Pilot Pressure forAttachment Valve
580 psi
Boom Down RegenerationValve Maximum Pilot Pressure
580 psi
Tool Program HydraulicTemperature High WarningEvent Threshold
258.8 Deg F
Attachment Valve #1 FlowSetting
13 gal/min
Attachment Valve #1 Multi-Operation Additional Flow
0 gal/min
Tool Program Attachment Valve#1 One Way/ Two Way ValveMode
Two Way
Attachment Valve #1 MaximumExtend Pressure
580 psi
Attachment Valve #1 MaximumRetract Pressure
580 psi
Multiple Operation MaximumExtend Pilot Pressure forAttachment Valve #1
580 psi
Multiple Operation MaximumRetract Pilot Pressure forAttachment Valve #1
580 psi
Attachment Valve #1 OpenTime
0.20 sec
Attachment Valve #1 CloseTime
0.20 sec
Attachment Valve #1 Tool FlowDirection
Normal
Attachment Valve #3 MaximumExtend Pressure
290 psi
Attachment Valve #3 MaximumRetract Pressure
290 psi
Attachment Valve #3 OpenTime
0.20 sec
Attachment Valve #3 CloseTime
0.20 sec
Attachment Valve #3 Tool FlowDirection
Normal
Description Value UnitTool Program Name CVP75Tool Program Tool Type CompactorMaximum Throttle Dial 10Minimum Throttle Dial Position 1Fuel Economy Mode EnableStatus
Enabled
Tool Program Pump FlowControl Mode
Combined Flow
Initial Tool Program MediumPressure Circuit Main PumpTorque Reduction
0 %
Total Tool Program MediumPressure Circuit Main PumpTorque Reduction
30 %
Variable Relief Valve #1Pressure
3191 psi
Variable Relief Valve #2Pressure
0 psi
Enhanced Multiple OperationAttachment Valve Limit EnableStatus
Disabled
Single Pump Mode MaximumExtend Pilot Pressure forAttachment Valve
580 psi
Single Pump Mode MaximumRetract Pilot Pressure forAttachment Valve
580 psi
Boom Down RegenerationValve Maximum Pilot Pressure
580 psi
Tool Program HydraulicTemperature High WarningEvent Threshold
258.8 Deg F
Attachment Valve #1 FlowSetting
32 gal/min
Attachment Valve #1 Multi-Operation Additional Flow
0 gal/min
Tool Program Attachment Valve#1 One Way/ Two Way ValveMode
One Way
Attachment Valve #1 MaximumExtend Pressure
580 psi
Multiple Operation MaximumExtend Pilot Pressure forAttachment Valve #1
580 psi
Attachment Valve #1 OpenTime
0.20 sec
Attachment Valve #1 CloseTime
0.20 sec
Attachment Valve #2 MaximumExtend Pressure
580 psi
Multiple Operation MaximumExtend Pilot Pressure forAttachment Valve #2
580 psi
Attachment Valve #2 OpenTime
0.20 sec
Attachment Valve #2 CloseTime
0.20 sec
Attachment Valve #3 MaximumExtend Pressure
290 psi
Attachment Valve #3 MaximumRetract Pressure
290 psi
Attachment Valve #3 OpenTime
0.20 sec
Attachment Valve #3 CloseTime
0.20 sec
Attachment Valve #3 Tool FlowDirection
Normal
Description Value UnitTool Program Name THUMB 1PTool Program Tool Type Bucket ThumbMaximum Throttle Dial 10Minimum Throttle Dial Position 1Fuel Economy Mode EnableStatus
Enabled
Tool Program Pump FlowControl Mode
Pump #2
Initial Tool Program MediumPressure Circuit Main PumpTorque Reduction
0 %
Total Tool Program MediumPressure Circuit Main PumpTorque Reduction
30 %
Variable Relief Valve #1Pressure
2799 psi
Variable Relief Valve #2Pressure
2799 psi
Enhanced Multiple OperationAttachment Valve Limit EnableStatus
Disabled
Single Pump Mode MaximumExtend Pilot Pressure forAttachment Valve
580 psi
Single Pump Mode MaximumRetract Pilot Pressure forAttachment Valve
580 psi
Boom Down RegenerationValve Maximum Pilot Pressure
580 psi
Tool Program HydraulicTemperature High WarningEvent Threshold
258.8 Deg F
Attachment Valve #1 FlowSetting
25 gal/min
Attachment Valve #1 Multi-Operation Additional Flow
0 gal/min
Tool Program Attachment Valve#1 One Way/ Two Way ValveMode
Two Way
Attachment Valve #1 MaximumExtend Pressure
580 psi
Attachment Valve #1 MaximumRetract Pressure
580 psi
Multiple Operation MaximumExtend Pilot Pressure forAttachment Valve #1
580 psi
Multiple Operation MaximumRetract Pilot Pressure forAttachment Valve #1
580 psi
Attachment Valve #1 OpenTime
0.20 sec
Attachment Valve #1 CloseTime
0.20 sec
Attachment Valve #1 Tool FlowDirection
Normal
Attachment Valve #3 MaximumExtend Pressure
290 psi
Attachment Valve #3 MaximumRetract Pressure
290 psi
Attachment Valve #3 OpenTime
0.20 sec
Attachment Valve #3 CloseTime
0.20 sec
Attachment Valve #3 Tool FlowDirection
Normal
Description Value UnitTool Program Name 0Tool Program Tool Type OtherMaximum Throttle Dial 10Minimum Throttle Dial Position 1Fuel Economy Mode EnableStatus
Enabled
Tool Program Pump FlowControl Mode
Pump #2
Initial Tool Program MediumPressure Circuit Main PumpTorque Reduction
0 %
Total Tool Program MediumPressure Circuit Main PumpTorque Reduction
30 %
Variable Relief Valve #1Pressure
5802 psi
Variable Relief Valve #2Pressure
5802 psi
Enhanced Multiple OperationAttachment Valve Limit EnableStatus
Disabled
Single Pump Mode MaximumExtend Pilot Pressure forAttachment Valve
580 psi
Single Pump Mode MaximumRetract Pilot Pressure forAttachment Valve
580 psi
Boom Down RegenerationValve Maximum Pilot Pressure
580 psi
Tool Program HydraulicTemperature High WarningEvent Threshold
258.8 Deg F
Attachment Valve #1 FlowSetting
0 gal/min
Attachment Valve #1 Multi-Operation Additional Flow
0 gal/min
Tool Program Attachment Valve#1 One Way/ Two Way ValveMode
Two Way
Attachment Valve #1 MaximumExtend Pressure
0 psi
Attachment Valve #1 MaximumRetract Pressure
0 psi
Multiple Operation MaximumExtend Pilot Pressure forAttachment Valve #1
580 psi
Multiple Operation MaximumRetract Pilot Pressure forAttachment Valve #1
580 psi
Attachment Valve #1 OpenTime
0.20 sec
Attachment Valve #1 CloseTime
0.20 sec
Attachment Valve #1 Tool FlowDirection
Normal
Attachment Valve #3 MaximumExtend Pressure
290 psi
Attachment Valve #3 MaximumRetract Pressure
290 psi
Attachment Valve #3 OpenTime
0.20 sec
Attachment Valve #3 CloseTime
0.20 sec
Attachment Valve #3 Tool FlowDirection
Normal
Description Value UnitTool Program Name 0Tool Program Tool Type BucketMaximum Throttle Dial 10
Minimum Throttle Dial Position 1Fuel Economy Mode EnableStatus
Enabled
Tool Program Pump FlowControl Mode
Pump #1
Initial Tool Program MediumPressure Circuit Main PumpTorque Reduction
0 %
Total Tool Program MediumPressure Circuit Main PumpTorque Reduction
30 %
Variable Relief Valve #1Pressure
5802 psi
Variable Relief Valve #2Pressure
5802 psi
Enhanced Multiple OperationAttachment Valve Limit EnableStatus
Disabled
Single Pump Mode MaximumExtend Pilot Pressure forAttachment Valve
580 psi
Single Pump Mode MaximumRetract Pilot Pressure forAttachment Valve
580 psi
Boom Down RegenerationValve Maximum Pilot Pressure
580 psi
Tool Program HydraulicTemperature High WarningEvent Threshold
258.8 Deg F
Attachment Valve #1 FlowSetting
0 gal/min
Attachment Valve #1 Multi-Operation Additional Flow
0 gal/min
Tool Program Attachment Valve#1 One Way/ Two Way ValveMode
Two Way
Attachment Valve #1 MaximumExtend Pressure
0 psi
Attachment Valve #1 MaximumRetract Pressure
0 psi
Multiple Operation MaximumExtend Pilot Pressure forAttachment Valve #1
580 psi
Multiple Operation MaximumRetract Pilot Pressure forAttachment Valve #1
580 psi
Attachment Valve #1 OpenTime
0.20 sec
Attachment Valve #1 CloseTime
0.20 sec
Attachment Valve #1 Tool FlowDirection
Normal
Attachment Valve #3 MaximumExtend Pressure
0 psi
Attachment Valve #3 MaximumRetract Pressure
0 psi
Attachment Valve #3 OpenTime
0.20 sec
Attachment Valve #3 CloseTime
0.20 sec
Attachment Valve #3 Tool FlowDirection
Normal
Description Value UnitTool Program Name 0Tool Program Tool Type BucketMaximum Throttle Dial 10Minimum Throttle Dial Position 1Fuel Economy Mode EnableStatus
Enabled
Tool Program Pump FlowControl Mode
Pump #1
Initial Tool Program MediumPressure Circuit Main PumpTorque Reduction
0 %
Total Tool Program MediumPressure Circuit Main PumpTorque Reduction
30 %
Variable Relief Valve #1Pressure
5802 psi
Variable Relief Valve #2Pressure
5802 psi
Enhanced Multiple OperationAttachment Valve Limit EnableStatus
Disabled
Single Pump Mode MaximumExtend Pilot Pressure forAttachment Valve
580 psi
Single Pump Mode MaximumRetract Pilot Pressure forAttachment Valve
580 psi
Boom Down RegenerationValve Maximum Pilot Pressure
580 psi
Tool Program HydraulicTemperature High WarningEvent Threshold
258.8 Deg F
Attachment Valve #1 FlowSetting
0 gal/min
Attachment Valve #1 Multi-Operation Additional Flow
0 gal/min
Tool Program Attachment Valve#1 One Way/ Two Way ValveMode
Two Way
Attachment Valve #1 MaximumExtend Pressure
0 psi
Attachment Valve #1 MaximumRetract Pressure
0 psi
Multiple Operation MaximumExtend Pilot Pressure forAttachment Valve #1
580 psi
Multiple Operation MaximumRetract Pilot Pressure forAttachment Valve #1
580 psi
Attachment Valve #1 OpenTime
0.20 sec
Attachment Valve #1 CloseTime
0.20 sec
Attachment Valve #1 Tool FlowDirection
Normal
Attachment Valve #3 MaximumExtend Pressure
0 psi
Attachment Valve #3 MaximumRetract Pressure
0 psi
Attachment Valve #3 OpenTime
0.20 sec
Attachment Valve #3 CloseTime
0.20 sec
Attachment Valve #3 Tool FlowDirection
Normal
Description Value UnitTool Program Name 0Tool Program Tool Type BucketMaximum Throttle Dial 10Minimum Throttle Dial Position 1Fuel Economy Mode EnableStatus
Enabled
Tool Program Pump FlowControl Mode
Pump #1
Initial Tool Program MediumPressure Circuit Main PumpTorque Reduction
0 %
Total Tool Program MediumPressure Circuit Main PumpTorque Reduction
30 %
Variable Relief Valve #1Pressure
5802 psi
Variable Relief Valve #2Pressure
5802 psi
Enhanced Multiple OperationAttachment Valve Limit EnableStatus
Disabled
Single Pump Mode MaximumExtend Pilot Pressure forAttachment Valve
580 psi
Single Pump Mode MaximumRetract Pilot Pressure forAttachment Valve
580 psi
Boom Down RegenerationValve Maximum Pilot Pressure
580 psi
Tool Program HydraulicTemperature High WarningEvent Threshold
258.8 Deg F
Attachment Valve #1 FlowSetting
0 gal/min
Attachment Valve #1 Multi-Operation Additional Flow
0 gal/min
Tool Program Attachment Valve#1 One Way/ Two Way ValveMode
Two Way
Attachment Valve #1 MaximumExtend Pressure
0 psi
Attachment Valve #1 MaximumRetract Pressure
0 psi
Multiple Operation MaximumExtend Pilot Pressure forAttachment Valve #1
580 psi
Multiple Operation MaximumRetract Pilot Pressure forAttachment Valve #1
580 psi
Attachment Valve #1 OpenTime
0.20 sec
Attachment Valve #1 CloseTime
0.20 sec
Attachment Valve #1 Tool FlowDirection
Normal
Attachment Valve #3 MaximumExtend Pressure
0 psi
Attachment Valve #3 MaximumRetract Pressure
0 psi
Attachment Valve #3 OpenTime
0.20 sec
Attachment Valve #3 CloseTime
0.20 sec
Attachment Valve #3 Tool FlowDirection
Normal
Description Value UnitTool Program Name 0Tool Program Tool Type BucketMaximum Throttle Dial 10Minimum Throttle Dial Position 1Fuel Economy Mode EnableStatus
Enabled
Tool Program Pump FlowControl Mode
Pump #1
Initial Tool Program MediumPressure Circuit Main PumpTorque Reduction
0 %
Total Tool Program MediumPressure Circuit Main PumpTorque Reduction
30 %
Variable Relief Valve #1Pressure
5802 psi
Variable Relief Valve #2Pressure
5802 psi
Enhanced Multiple OperationAttachment Valve Limit EnableStatus
Disabled
Single Pump Mode MaximumExtend Pilot Pressure forAttachment Valve
580 psi
Single Pump Mode MaximumRetract Pilot Pressure forAttachment Valve
580 psi
Boom Down RegenerationValve Maximum Pilot Pressure
580 psi
Tool Program HydraulicTemperature High WarningEvent Threshold
258.8 Deg F
Attachment Valve #1 FlowSetting
0 gal/min
Attachment Valve #1 Multi-Operation Additional Flow
0 gal/min
Tool Program Attachment Valve#1 One Way/ Two Way ValveMode
Two Way
Attachment Valve #1 MaximumExtend Pressure
0 psi
Attachment Valve #1 MaximumRetract Pressure
0 psi
Multiple Operation MaximumExtend Pilot Pressure forAttachment Valve #1
580 psi
Multiple Operation MaximumRetract Pilot Pressure forAttachment Valve #1
580 psi
Attachment Valve #1 OpenTime
0.20 sec
Attachment Valve #1 CloseTime
0.20 sec
Attachment Valve #1 Tool FlowDirection
Normal
Attachment Valve #3 MaximumExtend Pressure
0 psi
Attachment Valve #3 MaximumRetract Pressure
0 psi
Attachment Valve #3 OpenTime
0.20 sec
Attachment Valve #3 CloseTime
0.20 sec
Attachment Valve #3 Tool FlowDirection
Normal
Description Value UnitTool Program Name 0Tool Program Tool Type BucketMaximum Throttle Dial 10Minimum Throttle Dial Position 1
Fuel Economy Mode EnableStatus
Enabled
Tool Program Pump FlowControl Mode
Pump #1
Initial Tool Program MediumPressure Circuit Main PumpTorque Reduction
0 %
Total Tool Program MediumPressure Circuit Main PumpTorque Reduction
30 %
Variable Relief Valve #1Pressure
5802 psi
Variable Relief Valve #2Pressure
5802 psi
Enhanced Multiple OperationAttachment Valve Limit EnableStatus
Disabled
Single Pump Mode MaximumExtend Pilot Pressure forAttachment Valve
580 psi
Single Pump Mode MaximumRetract Pilot Pressure forAttachment Valve
580 psi
Boom Down RegenerationValve Maximum Pilot Pressure
580 psi
Tool Program HydraulicTemperature High WarningEvent Threshold
258.8 Deg F
Attachment Valve #1 FlowSetting
0 gal/min
Attachment Valve #1 Multi-Operation Additional Flow
0 gal/min
Tool Program Attachment Valve#1 One Way/ Two Way ValveMode
Two Way
Attachment Valve #1 MaximumExtend Pressure
0 psi
Attachment Valve #1 MaximumRetract Pressure
0 psi
Multiple Operation MaximumExtend Pilot Pressure forAttachment Valve #1
580 psi
Multiple Operation MaximumRetract Pilot Pressure forAttachment Valve #1
580 psi
Attachment Valve #1 OpenTime
0.20 sec
Attachment Valve #1 CloseTime
0.20 sec
Attachment Valve #1 Tool FlowDirection
Normal
Attachment Valve #3 MaximumExtend Pressure
0 psi
Attachment Valve #3 MaximumRetract Pressure
0 psi
Attachment Valve #3 OpenTime
0.20 sec
Attachment Valve #3 CloseTime
0.20 sec
Attachment Valve #3 Tool FlowDirection
Normal
Description Value UnitTool Program Name 0Tool Program Tool Type BucketMaximum Throttle Dial 10Minimum Throttle Dial Position 1Fuel Economy Mode EnableStatus
Enabled
Tool Program Pump FlowControl Mode
Pump #1
Initial Tool Program MediumPressure Circuit Main PumpTorque Reduction
0 %
Total Tool Program MediumPressure Circuit Main PumpTorque Reduction
30 %
Variable Relief Valve #1Pressure
5802 psi
Variable Relief Valve #2Pressure
5802 psi
Enhanced Multiple OperationAttachment Valve Limit EnableStatus
Disabled
Single Pump Mode MaximumExtend Pilot Pressure forAttachment Valve
580 psi
Single Pump Mode MaximumRetract Pilot Pressure forAttachment Valve
580 psi
Boom Down RegenerationValve Maximum Pilot Pressure
580 psi
Tool Program HydraulicTemperature High WarningEvent Threshold
258.8 Deg F
Attachment Valve #1 FlowSetting
0 gal/min
Attachment Valve #1 Multi-Operation Additional Flow
0 gal/min
Tool Program Attachment Valve#1 One Way/ Two Way ValveMode
Two Way
Attachment Valve #1 MaximumExtend Pressure
0 psi
Attachment Valve #1 MaximumRetract Pressure
0 psi
Multiple Operation MaximumExtend Pilot Pressure forAttachment Valve #1
580 psi
Multiple Operation MaximumRetract Pilot Pressure forAttachment Valve #1
580 psi
Attachment Valve #1 OpenTime
0.20 sec
Attachment Valve #1 CloseTime
0.20 sec
Attachment Valve #1 Tool FlowDirection
Normal
Attachment Valve #3 MaximumExtend Pressure
0 psi
Attachment Valve #3 MaximumRetract Pressure
0 psi
Attachment Valve #3 OpenTime
0.20 sec
Attachment Valve #3 CloseTime
0.20 sec
Attachment Valve #3 Tool FlowDirection
Normal
Description Value UnitTool Program Name 0Tool Program Tool Type BucketMaximum Throttle Dial 10Minimum Throttle Dial Position 1Fuel Economy Mode EnableStatus
Enabled
Tool Program Pump FlowControl Mode
Pump #1
Initial Tool Program MediumPressure Circuit Main PumpTorque Reduction
0 %
Total Tool Program MediumPressure Circuit Main PumpTorque Reduction
30 %
Variable Relief Valve #1Pressure
5802 psi
Variable Relief Valve #2Pressure
5802 psi
Enhanced Multiple OperationAttachment Valve Limit EnableStatus
Disabled
Single Pump Mode MaximumExtend Pilot Pressure forAttachment Valve
580 psi
Single Pump Mode MaximumRetract Pilot Pressure forAttachment Valve
580 psi
Boom Down RegenerationValve Maximum Pilot Pressure
580 psi
Tool Program HydraulicTemperature High WarningEvent Threshold
258.8 Deg F
Attachment Valve #1 FlowSetting
0 gal/min
Attachment Valve #1 Multi-Operation Additional Flow
0 gal/min
Tool Program Attachment Valve#1 One Way/ Two Way ValveMode
Two Way
Attachment Valve #1 MaximumExtend Pressure
0 psi
Attachment Valve #1 MaximumRetract Pressure
0 psi
Multiple Operation MaximumExtend Pilot Pressure forAttachment Valve #1
580 psi
Multiple Operation MaximumRetract Pilot Pressure forAttachment Valve #1
580 psi
Attachment Valve #1 OpenTime
0.20 sec
Attachment Valve #1 CloseTime
0.20 sec
Attachment Valve #1 Tool FlowDirection
Normal
Attachment Valve #3 MaximumExtend Pressure
0 psi
Attachment Valve #3 MaximumRetract Pressure
0 psi
Attachment Valve #3 OpenTime
0.20 sec
Attachment Valve #3 CloseTime
0.20 sec
Attachment Valve #3 Tool FlowDirection
Normal
Description Value UnitTool Program Name 0Tool Program Tool Type BucketMaximum Throttle Dial 10Minimum Throttle Dial Position 1Fuel Economy Mode EnableStatus
Enabled
Tool Program Pump FlowControl Mode
Pump #1
Initial Tool Program MediumPressure Circuit Main PumpTorque Reduction
0 %
Total Tool Program MediumPressure Circuit Main PumpTorque Reduction
30 %
Variable Relief Valve #1Pressure
5802 psi
Variable Relief Valve #2Pressure
5802 psi
Enhanced Multiple OperationAttachment Valve Limit EnableStatus
Disabled
Single Pump Mode MaximumExtend Pilot Pressure forAttachment Valve
580 psi
Single Pump Mode MaximumRetract Pilot Pressure forAttachment Valve
580 psi
Boom Down RegenerationValve Maximum Pilot Pressure
580 psi
Tool Program HydraulicTemperature High WarningEvent Threshold
258.8 Deg F
Attachment Valve #1 FlowSetting
0 gal/min
Attachment Valve #1 Multi-Operation Additional Flow
0 gal/min
Tool Program Attachment Valve#1 One Way/ Two Way ValveMode
Two Way
Attachment Valve #1 MaximumExtend Pressure
0 psi
Attachment Valve #1 MaximumRetract Pressure
0 psi
Multiple Operation MaximumExtend Pilot Pressure forAttachment Valve #1
580 psi
Multiple Operation MaximumRetract Pilot Pressure forAttachment Valve #1
580 psi
Attachment Valve #1 OpenTime
0.20 sec
Attachment Valve #1 CloseTime
0.20 sec
Attachment Valve #1 Tool FlowDirection
Normal
Attachment Valve #3 MaximumExtend Pressure
0 psi
Attachment Valve #3 MaximumRetract Pressure
0 psi
Attachment Valve #3 OpenTime
0.20 sec
Attachment Valve #3 CloseTime
0.20 sec
Attachment Valve #3 Tool FlowDirection
Normal
Description Value UnitTool Program Name 0Tool Program Tool Type BucketMaximum Throttle Dial 10Minimum Throttle Dial Position 1
Fuel Economy Mode EnableStatus
Enabled
Tool Program Pump FlowControl Mode
Pump #1
Initial Tool Program MediumPressure Circuit Main PumpTorque Reduction
0 %
Total Tool Program MediumPressure Circuit Main PumpTorque Reduction
30 %
Variable Relief Valve #1Pressure
5802 psi
Variable Relief Valve #2Pressure
5802 psi
Enhanced Multiple OperationAttachment Valve Limit EnableStatus
Disabled
Single Pump Mode MaximumExtend Pilot Pressure forAttachment Valve
580 psi
Single Pump Mode MaximumRetract Pilot Pressure forAttachment Valve
580 psi
Boom Down RegenerationValve Maximum Pilot Pressure
580 psi
Tool Program HydraulicTemperature High WarningEvent Threshold
258.8 Deg F
Attachment Valve #1 FlowSetting
0 gal/min
Attachment Valve #1 Multi-Operation Additional Flow
0 gal/min
Tool Program Attachment Valve#1 One Way/ Two Way ValveMode
Two Way
Attachment Valve #1 MaximumExtend Pressure
0 psi
Attachment Valve #1 MaximumRetract Pressure
0 psi
Multiple Operation MaximumExtend Pilot Pressure forAttachment Valve #1
580 psi
Multiple Operation MaximumRetract Pilot Pressure forAttachment Valve #1
580 psi
Attachment Valve #1 OpenTime
0.20 sec
Attachment Valve #1 CloseTime
0.20 sec
Attachment Valve #1 Tool FlowDirection
Normal
Attachment Valve #3 MaximumExtend Pressure
0 psi
Attachment Valve #3 MaximumRetract Pressure
0 psi
Attachment Valve #3 OpenTime
0.20 sec
Attachment Valve #3 CloseTime
0.20 sec
Attachment Valve #3 Tool FlowDirection
Normal
Description Value UnitTool Program Name 0Tool Program Tool Type BucketMaximum Throttle Dial 10Minimum Throttle Dial Position 1Fuel Economy Mode EnableStatus
Enabled
Tool Program Pump FlowControl Mode
Pump #1
Initial Tool Program MediumPressure Circuit Main PumpTorque Reduction
0 %
Total Tool Program MediumPressure Circuit Main PumpTorque Reduction
30 %
Variable Relief Valve #1Pressure
5802 psi
Variable Relief Valve #2Pressure
5802 psi
Enhanced Multiple OperationAttachment Valve Limit EnableStatus
Disabled
Single Pump Mode MaximumExtend Pilot Pressure forAttachment Valve
580 psi
Single Pump Mode MaximumRetract Pilot Pressure forAttachment Valve
580 psi
Boom Down RegenerationValve Maximum Pilot Pressure
580 psi
Tool Program HydraulicTemperature High WarningEvent Threshold
258.8 Deg F
Attachment Valve #1 FlowSetting
0 gal/min
Attachment Valve #1 Multi-Operation Additional Flow
0 gal/min
Tool Program Attachment Valve#1 One Way/ Two Way ValveMode
Two Way
Attachment Valve #1 MaximumExtend Pressure
0 psi
Attachment Valve #1 MaximumRetract Pressure
0 psi
Multiple Operation MaximumExtend Pilot Pressure forAttachment Valve #1
580 psi
Linkage Configuration - Machine Control 312E/F (DJE10115) Bucket - DISABLE
Boom Linkage - 381-1336
Stick Linkage - 394-7646
Multiple Operation MaximumRetract Pilot Pressure forAttachment Valve #1
580 psi
Attachment Valve #1 OpenTime
0.20 sec
Attachment Valve #1 CloseTime
0.20 sec
Attachment Valve #1 Tool FlowDirection
Normal
Attachment Valve #3 MaximumExtend Pressure
0 psi
Attachment Valve #3 MaximumRetract Pressure
0 psi
Attachment Valve #3 OpenTime
0.20 sec
Attachment Valve #3 CloseTime
0.20 sec
Attachment Valve #3 Tool FlowDirection
Normal
From To DistanceG H 0.0 mmG J 0.0 mmG Q 0.0 mmJ Q 0.0 mmJ J1 0.0 mm
From To DistanceA B 4650.0 mmA T 2155.0 mmA R 2824.0 mmB T 3101.0 mmB R 2281.0 mm
From To DistanceB C 916.0 mmB D 2620.0 mmB G 3000.0 mmB S 692.0 mmC D 1869.0 mmC G 2245.0 mmC S 1457.0 mmD G 381.0 mmB L 1460.0 mmL M 113.0 mm
Idler Link - 383-2513
Power Link - 383-2513
Monitor System
Product Link Pro (DJE10115)
Logged Diagnostic Codes [Total Operating Hours = 2187 hours] - Product Link Pro (DJE10115)
Logged Event Codes [Total Operating Hours = 2187 hours] - Product Link Pro (DJE10115)
Active Diagnostic Codes - Product Link Pro (DJE10115)
Active Event Codes - Product Link Pro (DJE10115)
Current Totals - Product Link Pro (DJE10115)
From To DistanceF D 528.0 mm
From To DistanceF H 508.0 mm
Parameter ValueECM Part Number 3095711-07Software Group Part Number 5251722-00Software Group Release Date NOV2016Software Group Description E HEX MONITOR Application
Parameter ValueProduct ID DJE10115Machine Serial NumberEquipment IDECM Part Number 4402105-14ECM Serial Number 3226S323YDSoftware Group Part Number 6045666-00Software Group Release Date Nov2020Software Group Description PL641_2020_11_07Application Software Part Number
Code Description Occ. First Last1888- 4 Local GPS Antenna : Voltage Below Normal 2 1808 1809
Code Description Occ. First LastNo LoggedEvent Codes
Code DescriptionNo ActiveDiagnosticCodes
Code DescriptionNo ActiveEvent Codes
Description Value Unit
Configuration - Product Link Pro (DJE10115)
Total Operating Hours 2187.7 hoursTotal Distance 15.16 Miles
Description Value UnitProduct ID DJE10115Equipment IDMachine Serial NumberMaintenance Mode OffSecurity System Machine NormalOperation Restore
Disabled or Not Installed
Security System Tamper ResistantConfiguration
Not Installed