PRODUCT NEWS Product Discontinuation Issue Date March 1, 2018 Fiber Sensor No. OMSQ-C (03)178130- EU Discontinuation Notice of Digital Fiber Amplifier Unit E3X- DA-S Series. Product Discontinuation Recommended Replacement Digital Fiber Amplifier Unit Smart Fiber Amplifier Unit Model E3X-DA□AN-S Model E3X-DAH□-S Model E3X-DAB□-S Model E3X-DAG□-S Model E3X-DAH6-S-40 Model E3X-DAT6-S-□ Model E3NX-FA□AN Model E3NX-FAH□ Color-Mark Fiber Amplifier Model E3NX-CA Series Model E3NX-CA Series No recommended replacement No recommended replacement Final order entry date The end of March 2019 Date of The Last Shipping The end of June 2019 Caution on recommended replacement When going to use E3NX-FA Series. Please pay attention to the following。 1) The dimensions of sensor are different. Please refer to the dimensions for details. 2) The operation methods are different. Please refer to operation methods for details. 3) The characteristics are different. Please refer to characteristics and operation ratings for details. 4) Notice that the position of output indicator is different. 5) The Control output (Residual voltage) is different. Please refer to characteristics and operation ratings for details. 6) Counter function is not available for E3NX-FA series. 7) Instead of ATC function, DPC is available for E3NX-FA series as an upwardly compatible function. Please refer to characteristics and operation ratings for details. 8) Optical communication to E3X-DA-S series is not available for E3NX-FA. Notice that channel recognition and Mutual interference prevention is not available at communication status. 9) Mobile console E3X-MC11-SV2 is not available for E3NX-FA series. OMRON Corporation Industrial Automation Company No. OMSQ-C (03)178130- EU
Transcript
PRODUCTNEWS Product Discontinuation
Notices Issue DateMarch 1, 2018
Fiber Sensor No. OMSQ-C (03)178130-EU
Discontinuation Notice of Digital Fiber Amplifier Unit E3X-DA-S Series.
Product Discontinuation Recommended ReplacementDigital Fiber Amplifier Unit Smart Fiber Amplifier Unit
Model E3X-DA□AN-SModel E3X-DAH□-S
Model E3X-DAB□-SModel E3X-DAG□-SModel E3X-DAH6-S-40Model E3X-DAT6-S-□
Caution on recommended replacementWhen going to use E3NX-FA Series. Please pay attention to the following。1) The dimensions of sensor are different. Please refer to the dimensions for details.2) The operation methods are different. Please refer to operation methods for details.3) The characteristics are different. Please refer to characteristics and operation ratings for details.4) Notice that the position of output indicator is different.5) The Control output (Residual voltage) is different. Please refer to characteristics and operation
ratings for details.6) Counter function is not available for E3NX-FA series.7) Instead of ATC function, DPC is available for E3NX-FA series as an upwardly compatible function.
Please refer to characteristics and operation ratings for details.8) Optical communication to E3X-DA-S series is not available for E3NX-FA. Notice that channel
recognition and Mutual interference prevention is not available at communication status.9) Mobile console E3X-MC11-SV2 is not available for E3NX-FA series.10) The Communication Unit E3X-DRT21-S VER.3/E3X-CRT/E3X-ECT cannot be connected to E3NX-FA series. When going to use E3NX-CA Series. Please pay attention to the following。1)E3X-DAB(blue)、E3X-DAG(green) can distinguish power with contrast mode.2) When using to distinguish several objects. Please to check whether each object can be distinguished.*Because of the difference of RGB turning, when there are several kinds of color, maybe it will be unable to distinguish.
Difference from discontinued product
OMRON Corporation Industrial Automation Company No. OMSQ-C (03)178130-EU
Recommended replacement Model
Body Color
Dimen-sions
Wire connection
Mounting Dimensions
Charac-teristics
Operation ratings
Operation methods
Mode E3NX-FA Series * * ** ** * * *Mode E3NX-CA Series * * ** ** * * *
** : Compatible* : The change is a little/Almost compatible-- : Not compatible- : No corresponding specification
Product Discontinuation and recommended replacement
Recommendable replacementModel E3NX-CA SeriesModel E3NX-FA Series
Pre-wired Amplifiers
4
Wire-saving connector
5
Characteristics
Analog output models(E3X-DA□AN-S) Product discontinuation
Model E3X-DA□AN-SRecommendable replacement
Model E3NX-FA□ANLight source(wavelength) Red LED(635nm) Red, 4-element LED(625nm)Power supply voltage DC12～24V±10%,ripple(p-p)10% max. 10 to 30 VDC, including 10% ripple(p-p)Powerconsumption(Power supply voltage 24V)
Normal mode 1080mW max. 960mW max.Eco function ON - 770mW max.
Eco function LO - 870mW max.
Controloutput
ON/OFF output
Load power supply voltage: 26.4VDC; NPN/PNP open collector; load current: 50mA max.;Residual voltage: 1V max.
Load Power supply voltage: 30 VDC max., open-collector output (depends on the NPN/PNP output format) Load current: Groups of 1 to 3 Amplifier Units: 100 mA max., Groups of 4 to 30 Amplifier Units: 20 mA max.Residual voltage: At load current of less than 10 mA: 1 V max. At load current of 10 to 100 mA: 2 V max.OFF current: 0.1 mA max.
Analog output
Control outputVoltage output: 1 to 5 VDC (Connection load 10kΩ min.)Temperature Characteristics0.3%F.S./℃Response speed/repeat accuracySuper-high-speed mode:80μs/1.5%F.S.High-speed mode:250μs/1.5%F.S.Standard mode:1 ms/1%F.S.High-resolution mode:4ms/0.75%F.S.
Smart Tuning (2-point tuning, full auto tuning, position tuning, maximum sensitivity tuning, power tuning, or percentage tuning(-99% to 99%)) or manual adjustment
Functions Automatic power control(APC)
Always enabled Always enabled.
Dynamic power control(DPC) - Provided
Timer function
Select from OFF-delay, ON-delay, or oneshot timer.1 ms to 5s(1 to 20 ms set in 1-ms increments, 20 to 200 ms set in 10-ms increments,200 ms to 1 s set in 100-ms increments, and 1 to 5 s set in 1 s-increments)
Select from timer disabled, OFF-delay, ON-delay, one-shot, or ON-delay + OFF-delay timer: 1 to 9,999 ms
Zero-reset Negative values can be displayed. (Threshold value is shifted.)
Negative values can be displayed. (Threshold value is shifted.)
Setting reset Settings can be returned to defaults as required.
Select from initial reset (factory defaults) or user reset (saved settings).
Eco mode -Select from OFF (digital display lit), Eco ON (digital display not lit), and Eco LO (digital display dimmed).
Bank switching - Select from banks 1 to 4.
Power tuning Light emission power and reception gain, digital control method Select from ON or OFF
Output 1 - Select from normal detection mode or area detection mode.
Output 2 - Select from Analog scaling or Analog offset.
Hysteresis width - Select from standard setting or user setting. For a user setting, the hysteresis width can be set from 0 to 9,999.
6
No. of Units for mutual interference prevention
Possible for up to 10 unitsSuper-high-speed mode (SHS):0
7-segment displays (Sub digital display: green, Main digital display: white)Display direction: Switchable between normal and reversed.OUT indicator (orange), L/D indicator(orange),ST indicator(blue), DPC indicator (green), and OUT selection indicator( orange, only on models with 2 outputs)
Ambient illumination(Receiver side)
Incandescent lamp 10，000 lx max. 20，000 lx max.
Sunlight 20,000lx lx max. 30,000l lx max.
Ambient temperaturerange
Operating
Groups of 1 to 2 Amplifiers: -25 to ℃55℃Groups of 3 to 10 Amplifiers: -25 to ℃50℃Groups of 11 to 16 Amplifiers: -25 to ℃45℃
Groups of 1 to 2 Amplifiers: -25 to 55℃ ℃Groups of 3 to 10 Amplifiers: -25 to ℃50℃Groups of 11 to 16 Amplifiers: -25 to ℃45℃Groups of 17 to 30 Amplifiers: -25 to ℃40℃
Storage -30 to 70 (with no icing or ℃ ℃condensation)
-30 to 70 (with no icing or ℃ ℃condensation)
Weight(packed state)
Pre-wired model Approx.100g Approx.115gAmplifier unit connector model Approx.55g Approx.60g
Model E3NX-FAH□Light source(wavelength) Infrared LED(870nm) Infrared model(870nm)Power supply voltage DC12～24V±10%,ripple(p-p)10% max. 10 to 30 VDC, including 10% ripple(p-p)Power consumption(Powersupply 24V)
Normal mode 960mW max. 1080mW max.Eco function ON - 920mW max.
Eco function LO - 1020mW max.
Control outputLoad power supply voltage: 26.4VDC; NPN/PNP open collector; load current: 50mA max.; residual voltage: 1V max.
Load Power supply voltage: 30 VDC max., open-collector output (depends on the NPN/PNP output format) Load current: Groups of 1 to 3 Amplifier Units: 100 mA max., Groups of 4 to 30 Amplifier Units: 20 mA max.Residual voltage: At load current of less than 10 mA: 1 V max. At load current of 10 to 100 mA: 2 V max.OFF current: 0.1 mA max.
Smart Tuning (2-point tuning, full auto tuning, position tuning, maximum sensitivity tuning, power tuning, or percentage tuning(-99% to 99%)) or manual adjustment
Functions
Automatic power control(APC)
High-speed control method for emission current Always enabled.
Dynamic power control(DPC) - Provided
Timer function
Select from OFF-delay, ON-delay, or one-shot timer.1 mms to 5s(1 to 20 mms set in 1-ms increments, 20 to 200 mms set in 10-ms increments,200 mms to 1 s set in 100-ms increments, and 1 to 5 s set in 1 s-increments)
Select from timer disabled, OFF-delay, ON-delay, one-shot, or ON-delay + OFF-delay timer: 1 to 9,999 ms
Zero-reset Negative values can be displayed. (Threshold value is shifted.)
Negative values can be displayed. (Threshold value is shifted.)
Setting reset Settings can be returned to defaults as required.
Select from initial reset (factory defaults) or user reset (saved settings).
Eco mode -Select from OFF (digital display lit), Eco ON (digital display not lit), and Eco LO (digital display dimmed).
Bank switching - Select from banks 1 to 4.
Power tuning Light emission power and reception gain, digital control method Select from ON or OFF
Output 1 - Select from normal detection mode or area detection mode.
Hysteresis width -Select from standard setting or user setting. For a user setting, the hysteresis width can be set from 0 to 9,999.
7-segment displays (Sub digital display: green, Main digital display: white) Display direction: Switchable between
8
normal and reversed.OUT indicator (orange), L/D indicator(orange),ST indicator(blue), DPC indicator (green), and OUT selection indicator( orange, only on models with 2 outputs)
Ambientillumination(Receiver side
Incandescent lamp 10，000 lx max. 20，000 lx max.
Sunlight 20,000lx lx max. 30,000l lx max.
Ambienttemperaturerange
Operating
Groups of 1 to 2 Amplifiers: -25℃ to 55℃Groups of 3 to 10 Amplifiers: -25℃ to 50℃Groups of 11 to 16 Amplifiers: -25℃ to 45℃
Groups of 1 to 2 Amplifiers: -25℃ to 55℃Groups of 3 to 10 Amplifiers: -25℃ to 50℃Groups of 11 to 16 Amplifiers: -25℃ to 45℃Groups of 17 to 30 Amplifiers: -25℃ to 40℃
Storage -30℃ to 70℃(with no icing or condensation)
-30℃ to 70℃(with no icing or condensation)
Weight(packed state)
Pre-wired model Approx.100g Approx.105gAmplifier unit connector model Approx.55g Approx.60g
E3X-DAB□-SGreen LED (525 nm)E3X-DAG-□-SBlue LED (470 nm)
White LED(420～700nm)
Power consumption(Power supply voltage 24V) DC12～24V±10％ ripple (p-p)10% 10 to 30 VDC, including 10% ripple(p-p)
Power consumption(Power supply voltage 24V)
Normal mode 960mW max. 960mW max.Eco function ON - 720mW Max.
Eco function LO - 800mW max.
Control output
Load power supply voltage: 26.4 VDC; NPN/PNP open collector; load current: 50 mA max.; residual voltage: 1 V max.
Load Power supply voltage: 30 VDC max., open-collector output (depends on the NPN/PNP output format) Load current: Groups of 1 to 3 Amplifier Units: 100 mA max., Groups of 4 to 30 Amplifier Units: 20 mA max.Residual voltage: At load current of less than 10 mA: 1 V max. At load current of 10 to 100 mA: 2 V max.OFF current: 0.1 mA max.
Sensitivity setting Teaching or manual methodSmart Tuning (2-point tuning, full auto tuning, or 1-point tuning (1% to 99%)) or manual adjustment
Functions
Automatic power control (APC) Always enabled -
Operation mode -
contrast Mode: NO(Light-ON) or NC (Dark-ON)Color Mode: NO(ON for match: ON for same color as registered color) or NC (ON for mismatch: ON for different color
9
from registered color)
Timer
Select from OFF-delay, ON-delay, or oneshot timer. 1 ms to 5s(1 to 20 ms set in 1-ms increments, 20 to 200 ms set in 10-ms increments,200 ms to 1 s set in 100-ms increments, and 1 to 5 s set in 1 s-increments)
Select from timer disabled, OFF-delay, ON-delay, one-shot, or ON-delay + OFF-delay timer (Counted by 0.1s in a range of 0.1 to 0.5ms, by 0.5ms for 0.5 to 5 ms, and by 1 ms for 5 to 9999 ms. Default: 10 ms, Error: 0.1 ms)
Zero reset Negative values can be displayed. (Threshold value is shifted.)
Contrast Mode onlyNegative values can be displayed. (Threshold level is shifted.)
Resetting settings Settings can be returned to defaults as required.
Select from initial reset (factory defaults), user reset (saved settings), or bank reset.
Eco mode -Select from OFF (digital display lit), Eco ON (digital display not lit), and Eco LO (digital display dimmed).
Bank switching - Select from banks 1 to 8.
Power tuning level Light emission power and reception gain, digital control method
Set from 100 to 9,999. (The RGB maximum incident level at Smart Tuning is adjusted to the power tuning level.)
Changing the displays -
Threshold level and incident level, channel number and incident level, RGB display and incident level, or bank display and incident level
No. of Units for mutual interference prevention
Possible for up to 10 unitsSuper-high-speed mode (SHS) : 0
7-segment displays (Sub digital display: green, Main digital display: white)Display direction: Switchable between normal and reversed.OUT indicator (orange), NO/NC indicator(orange), Smart Tuning indicator(blue), and OUT selection indicator (orange, only on models with 2 outputs)
Ambient illumination(Receiver side
Incandescent lamp 10，000 lx max. 20，000 lx max.
Sunlight 20,000lx lx max. 30,000l lx max.
Ambient temperature range
Operating
Groups of 1 to 2 Amplifiers: -25 to ℃55℃Groups of 3 to 10 Amplifiers: -25 to ℃50℃Groups of 11 to 16 Amplifiers: -25 to ℃45℃
Groups of 1 to 2 Amplifiers: -25 to ℃55℃Groups of 3 to 10 Amplifiers: -25 to ℃50℃Groups of 11 to 16 Amplifiers: -25 to ℃45℃Groups of 17 to 30 Amplifiers: -25 to ℃40℃
Storage -30℃ to 70℃(with no icing or condensation)
-30℃ to 70℃(with no icing or condensation)
Weight(packed state)
Pre-wired model Approx.100g Approx. 115gAmplifier unit connector model Approx.55g Approx. 20g
Operation ratingsProduct discontinuationModel E3X-DA-S Series
Recommendable replacementModel E3NX-CA SeriesModel E3NX-FA Series
Sensing distance Sensing distance
Operation methodsProduct discontinuationModel E3X-DA-S Series
Recommendable replacementModel E3NX-CA SeriesModel E3NX-FA Series
E3X-DA□AN-S
E3X-DA□-S
E3NX-FA Series
E3NX-CA Series
Specifications and prices in this product news are as of the issue date and are subject to change without notice.Only main changes in specifications are described in this document. Please be sure to read the relevant catalogs, datasheets, product specifications, instructions, and manuals for precautions and necessary information when using products.
