25 Benson Rd, Nuffield Industrial Estate
Poole, Dorset. BH17 0GB
Tel: 01202 681190
Fax: 01202 677909
E-mail: [email protected]
PROLEC RATED CAPACITY INDICATOR.
PLEASE READ AND UNDERSTAND THE OPERATING
INSTRUCTIONS BEFORE USING THE EQUIPMENT
M/C Serial No.
M/C Plant No.
Compiled
IN
50 - 150mm
2.50 3.00 3.50 4.00 4.50 5.00 5.50 6.00 6.50 7.00 7.50 8.00
8.00 6.37
7.50 5.04 4.05
7.00 4.12 3.40
6.50 4.14 3.44 2.89
6.00 3.45 2.91 2.49
5.50 3.45 2.92 2.50
5.00 4.04a 3.43 2.91 2.50 2.17
4.50 3.91a 3.42 2.90 2.50 2.17
4.00 3.93a 3.39 2.88 2.48 2.16 1.90
3.50 3.60a 4.02 3.36 2.86 2.47 2.15 1.89
3.00 4.12a 3.97 3.32 2.83 2.45 2.14 1.89
2.50 4.80 3.92 3.29 2.81 2.43 2.13 1.88
2.00 4.73 3.87 3.25 2.78 2.41 2.12 1.87
1.50 4.66 3.82 3.21 2.75 2.39 2.10 1.87
1.00 4.60 3.78 3.18 2.73 2.38 2.09 1.86
0.50 5.75 4.56 3.75 3.16 2.71 2.36 2.08 1.86
(m) 0.00 7.63 5.71 4.53 3.72 3.14 2.70 2.36 2.08
-0.50 6.65a 7.61 5.69 4.51 3.71 3.13 2.69 2.35 2.09
-1.00 8.29a 7.61 5.69 4.50 3.70 3.13 2.69 2.36
-1.50 7.63 5.69 4.51 3.71 3.14 2.70
-2.00
-2.50
-3.00
-3.50
-4.00
NOTES Loads refer to the maximum SWL in TONNES for the designated operation without attachments fitted
and assume the load is suspended vertically below the bucket pin.
The weight of bucket, slings/auxillary devices must be deducted from the above loads.
Radius/height is given in METRES measured from slew centre/ground level respectively.
Loads marked 'b' boom and 'a' arm are limited by hydraulic capacity (87% of Maximum System Hydraulic
PAGE 1 of 23 Pressure).
H
e
i
g
h
t
03.12.2009 DPM
8485
CRR624
Colmar T7000Machine Type
Equipment
3AU
RCI Serial No
CANTED RAIL FRONT FLOATING
UNLOCKED
3m57 + 3m10 Tele Dipper
EXTENDED
± 10°
Radius (m)
Op Mode
Sector
Osc. Axle
Dipper Counterweight
25 Benson Rd, Nuffield Industrial Estate
Poole, Dorset. BH17 0GB
Tel: 01202 681190
Fax: 01202 677909
E-mail: [email protected]
PROLEC RATED CAPACITY INDICATOR.
PLEASE READ AND UNDERSTAND THE OPERATING
INSTRUCTIONS BEFORE USING THE EQUIPMENT
M/C Serial No.
M/C Plant No.
Compiled
IN
50 - 150mm
2.50 3.00 3.50 4.00 4.50 5.00 5.50 6.00 6.50 7.00 7.50 8.00
8.00 6.94a
7.50 6.06b 5.53a
7.00 5.52a 5.22a
6.50 5.05a 5.20a 4.83a
6.00 4.89a 5.00a 4.18a
5.50 4.62a 4.86a 4.47
5.00 4.04a 4.43a 4.74a 4.47 3.85
4.50 3.91a 4.34a 4.69a 4.46 3.86
4.00 3.93a 4.38a 4.73a 4.44 3.85 3.29a
3.50 3.60a 4.14a 4.58a 4.91a 4.42 3.83 3.36
3.00 4.12a 4.62a 4.98a 5.13 4.39 3.81 3.35
2.50 5.24a 5.49a 5.66a 5.09 4.36 3.79 3.34
2.00 7.52a 6.97a 5.99 5.05 4.33 3.77 3.33
1.50 9.12 7.22 5.94 5.01 4.31 3.75 3.31
1.00 9.02 7.16 5.89 4.98 4.28 3.74 3.31
0.50 9.99 8.95 7.11 5.85 4.95 4.26 3.73 3.31
(m) 0.00 9.99 9.99 8.90 7.07 5.83 4.93 4.25 3.72
-0.50 6.65a 9.99 9.99 8.87 7.04 5.81 4.92 4.25 3.73
-1.00 8.29a 9.99 9.99 8.86 7.04 5.81 4.92 4.26
-1.50 9.99 9.99 8.87 7.05 5.82 4.94
-2.00
-2.50
-3.00
-3.50
-4.00
NOTES Loads refer to the maximum SWL in TONNES for the designated operation without attachments fitted
and assume the load is suspended vertically below the bucket pin.
The weight of bucket, slings/auxillary devices must be deducted from the above loads.
Radius/height is given in METRES measured from slew centre/ground level respectively.
Loads marked 'b' boom and 'a' arm are limited by hydraulic capacity (87% of Maximum System Hydraulic
PAGE 2 of 23 Pressure).
H
e
i
g
h
t
03.12.2009 DPM
CANTED RAIL FRONT FLOATING END
LOCKED
Radius (m)
Op Mode
Sector ± 10°
Machine Type
Equipment
RCI Serial No
Dipper
3AL
Colmar T7000
Extended Counterweight
3m57 + 3m10 Tele Dipper
Osc. Axle
8485
CRR624
25 Benson Rd, Nuffield Industrial Estate
Poole, Dorset. BH17 0GB
Tel: 01202 681190
Fax: 01202 677909
E-mail: [email protected]
PROLEC RATED CAPACITY INDICATOR.
PLEASE READ AND UNDERSTAND THE OPERATING
INSTRUCTIONS BEFORE USING THE EQUIPMENT
M/C Serial No.
M/C Plant No.
Compiled
OUT
50 - 150mm
2.50 3.00 3.50 4.00 4.50 5.00 5.50 6.00 6.50 7.00 7.50 8.00
8.00 6.79
7.50 5.53 4.56
7.00 4.62 3.89
6.50 4.64 3.92 3.36
6.00 3.93 3.38 2.93
5.50 3.93 3.39 2.95
5.00 4.04a 3.92 3.38 2.95 2.59
4.50 3.91a 3.91 3.37 2.94 2.59
4.00 3.93a 3.88 3.35 2.93 2.59 2.30
3.50 3.60a 4.14a 3.85 3.33 2.92 2.58 2.30
3.00 4.12a 4.49 3.82 3.31 2.90 2.57 2.29
2.50 5.24a 4.44 3.79 3.28 2.88 2.55 2.28
2.00 5.25 4.39 3.75 3.26 2.86 2.54 2.27
1.50 5.19 4.35 3.72 3.23 2.84 2.53 2.27
1.00 5.14 4.31 3.69 3.21 2.83 2.52 2.26
0.50 6.25 5.10 4.28 3.67 3.19 2.82 2.51 2.27
(m) 0.00 7.97 6.22 5.07 4.26 3.65 3.18 2.81 2.51
-0.50 6.65a 7.95 6.20 5.06 4.24 3.64 3.18 2.81 2.51
-1.00 8.29a 7.95 6.20 5.05 4.24 3.64 3.18 2.81
-1.50 7.97 6.21 5.06 4.25 3.65 3.19
-2.00
-2.50
-3.00
-3.50
-4.00
NOTES Loads refer to the maximum SWL in TONNES for the designated operation without attachments fitted
and assume the load is suspended vertically below the bucket pin.
The weight of bucket, slings/auxillary devices must be deducted from the above loads.
Radius/height is given in METRES measured from slew centre/ground level respectively.
Loads marked 'b' boom and 'a' arm are limited by hydraulic capacity (87% of Maximum System Hydraulic
PAGE 3 of 23 Pressure).
RCI Serial No
Radius (m)
Op Mode
Sector
Osc. Axle
Dipper
CANTED RAIL FRONT FLOATING END
UNLOCKED
3m57 + 3m10 Tele Dipper
EXTENDED Counterweight
± 10°
H
e
i
g
h
t
03.12.2009 DPM
8485
CRR624
Colmar T7000Machine Type
Equipment
3AUC
25 Benson Rd, Nuffield Industrial Estate
Poole, Dorset. BH17 0GB
Tel: 01202 681190
Fax: 01202 677909
E-mail: [email protected]
PROLEC RATED CAPACITY INDICATOR.
PLEASE READ AND UNDERSTAND THE OPERATING
INSTRUCTIONS BEFORE USING THE EQUIPMENT
M/C Serial No.
M/C Plant No.
Compiled
OUT
50 - 150mm
2.50 3.00 3.50 4.00 4.50 5.00 5.50 6.00 6.50 7.00 7.50 8.00
8.00 6.94a
7.50 6.06b 5.53a
7.00 5.52a 5.22a
6.50 5.05a 5.20a 4.83a
6.00 4.89a 5.00a 4.18a
5.50 4.62a 4.86a 4.79a
5.00 4.04a 4.43a 4.74a 4.86a 4.26a
4.50 3.91a 4.34a 4.69a 4.87a 4.68a
4.00 3.93a 4.38a 4.73a 4.94a 4.86a 3.29a
3.50 3.60a 4.14a 4.58a 4.91a 5.09a 4.87 4.15a
3.00 4.12a 4.62a 4.98a 5.23a 5.35a 4.85 4.34
2.50 5.24a 5.49a 5.66a 5.74a 5.46 4.84 4.33
2.00 7.52a 6.97a 6.68a 6.19 5.43 4.82 4.32
1.50 9.99 8.39 7.12 6.16 5.41 4.80 4.31
1.00 9.99 8.33 7.08 6.13 5.38 4.79 4.30
0.50 9.99 9.99 8.28 7.04 6.10 5.37 4.78 3.97a
(m) 0.00 9.99 9.99 9.96 8.25 7.02 6.09 5.36 4.77
-0.50 6.65a 9.99 9.99 9.94 8.23 7.01 6.08 5.35 4.78
-1.00 8.29a 9.99 9.99 9.93 8.23 7.00 6.08 5.36
-1.50 9.99 9.99 9.94 8.24 7.01 6.09
-2.00
-2.50
-3.00
-3.50
-4.00
NOTES Loads refer to the maximum SWL in TONNES for the designated operation without attachments fitted
and assume the load is suspended vertically below the bucket pin.
The weight of bucket, slings/auxillary devices must be deducted from the above loads.
Radius/height is given in METRES measured from slew centre/ground level respectively.
Loads marked 'b' boom and 'a' arm are limited by hydraulic capacity (87% of Maximum System Hydraulic
PAGE 4 of 23 Pressure).
Machine Type
Equipment
8485
CRR624
Colmar T7000
RCI Serial No
3m57 + 3m10 Tele Dipper
H
e
i
g
h
t
03.12.2009 DPM
LOCKED
Radius (m)
3ALC
± 10°
EXTENDED Counterweight
Op Mode
Sector
Osc. Axle
Dipper
CANTED RAIL FRONT FLOATING END
25 Benson Rd, Nuffield Industrial Estate
Poole, Dorset. BH17 0GB
Tel: 01202 681190
Fax: 01202 677909
E-mail: [email protected]
PROLEC RATED CAPACITY INDICATOR.
PLEASE READ AND UNDERSTAND THE OPERATING
INSTRUCTIONS BEFORE USING THE EQUIPMENT
M/C Serial No.
M/C Plant No.
Compiled
IN
50 - 150mm
2.50 3.00 3.50 4.00 4.50 5.00 5.50 6.00 6.50 7.00 7.50 8.00
8.00 2.92
7.50 2.38
7.00 2.43 1.95
6.50 1.98 1.62
6.00 1.99 1.64 1.36
5.50 1.99 1.64 1.36 1.13
5.00 1.97 1.63 1.36 1.14
4.50 1.95 1.62 1.35 1.14 0.96
4.00 2.37 1.93 1.60 1.34 1.13 0.96
3.50 2.92 2.32 1.89 1.57 1.32 1.12 0.95
3.00 2.84 2.27 1.86 1.54 1.30 1.10 0.94
2.50 2.21 1.81 1.51 1.28 1.09 0.93 0.81
2.00 2.16 1.77 1.48 1.26 1.07 0.92 0.80
1.50 2.61 2.10 1.74 1.46 1.24 1.06 0.91
1.00 2.55 2.06 1.70 1.43 1.22 1.05 0.91
0.50 2.50 2.03 1.68 1.41 1.20 1.04 0.90
(m) 0.00 3.17 2.47 2.00 1.66 1.40 1.20 1.03 0.91
-0.50 4.27 3.15 2.46 1.99 1.65 1.39 1.19 1.03
-1.00 6.45 4.28 3.14 2.45 1.98 1.64 1.39 1.19
-1.50 4.29 3.15 2.46 1.99 1.65 1.40
-2.00
-2.50
-3.00
-3.50
-4.00
NOTES Loads refer to the maximum SWL in TONNES for the designated operation without attachments fitted
and assume the load is suspended vertically below the bucket pin.
The weight of bucket, slings/auxillary devices must be deducted from the above loads.
Radius/height is given in METRES measured from slew centre/ground level respectively.
Loads marked 'b' boom and 'a' arm are limited by hydraulic capacity (87% of Maximum System Hydraulic
PAGE 5 of 23 Pressure).
Machine Type Colmar T7000 8485
RCI Serial No CRR624
Equipment 3m57 + 3m10 Tele Dipper 03.12.2009 DPM
3B Op Mode CANTED RAIL FRONT FLOATING END
Sector ± 10° - 45°
UNLOCKED
Dipper EXTENDED Counterweight
Radius (m)
H
e
i
g
h
t
U Osc. Axle
25 Benson Rd, Nuffield Industrial Estate
Poole, Dorset. BH17 0GB
Tel: 01202 681190
Fax: 01202 677909
E-mail: [email protected]
PROLEC RATED CAPACITY INDICATOR.
PLEASE READ AND UNDERSTAND THE OPERATING
INSTRUCTIONS BEFORE USING THE EQUIPMENT
M/C Serial No.
M/C Plant No.
Compiled
IN
50 - 150mm
2.50 3.00 3.50 4.00 4.50 5.00 5.50 6.00 6.50 7.00 7.50 8.00
8.00 5.33
7.50 4.18
7.00 4.26 3.36
6.50 3.40 2.75
6.00 3.42 2.77 2.28
5.50 3.41 2.78 2.29 1.90
5.00 3.39 2.76 2.29 1.91
4.50 3.36 2.74 2.28 1.91 1.61
4.00 3.71a 3.32 2.71 2.25 1.90 1.61
3.50 3.33a 3.92a 3.27 2.67 2.23 1.88 1.60
3.00 3.86a 4.01 3.21 2.63 2.20 1.86 1.58
2.50 3.92 3.14 2.59 2.16 1.83 1.57 1.35
2.00 3.83 3.08 2.54 2.13 1.81 1.55 1.35
1.50 4.80 3.74 3.02 2.50 2.10 1.79 1.54
1.00 4.70 3.67 2.97 2.46 2.07 1.77 1.53
0.50 4.63 3.62 2.93 2.43 2.05 1.76 1.52
(m) 0.00 6.19 4.58 3.58 2.90 2.41 2.04 1.75 1.53
-0.50 8.81a 6.16 4.55 3.55 2.88 2.40 2.03 1.75
-1.00 7.02a 9.24 6.15 4.54 3.55 2.88 2.40 2.04
-1.50 9.27 6.17 4.55 3.55 2.89 2.41
-2.00
-2.50
-3.00
-3.50
-4.00
NOTES Loads refer to the maximum SWL in TONNES for the designated operation without attachments fitted
and assume the load is suspended vertically below the bucket pin.
The weight of bucket, slings/auxillary devices must be deducted from the above loads.
Radius/height is given in METRES measured from slew centre/ground level respectively.
Loads marked 'b' boom and 'a' arm are limited by hydraulic capacity (87% of Maximum System Hydraulic
PAGE 6 of 23 Pressure).
Machine Type Colmar T7000 8485
RCI Serial No CRR624
Equipment 3m57 + 3m10 Tele Dipper 03.12.2009 DPM
3B Op Mode CANTED RAIL FRONT FLOATING END
Sector ± 10° - 45°
LOCKED
Dipper EXTENDED Counterweight
Radius (m)
H
e
i
g
h
t
L Osc. Axle
25 Benson Rd, Nuffield Industrial Estate
Poole, Dorset. BH17 0GB
Tel: 01202 681190
Fax: 01202 677909
E-mail: [email protected]
PROLEC RATED CAPACITY INDICATOR.
PLEASE READ AND UNDERSTAND THE OPERATING
INSTRUCTIONS BEFORE USING THE EQUIPMENT
M/C Serial No.
M/C Plant No.
Compiled
OUT
50 - 150mm
2.50 3.00 3.50 4.00 4.50 5.00 5.50 6.00 6.50 7.00 7.50 8.00
8.00 3.44
7.50 2.87
7.00 2.91 2.42
6.50 2.44 2.05
6.00 2.45 2.07 1.76
5.50 2.45 2.07 1.77 1.51
5.00 2.43 2.06 1.77 1.52
4.50 2.42 2.05 1.76 1.52 1.31
4.00 2.86 2.39 2.03 1.74 1.51 1.31
3.50 3.33a 2.82 2.36 2.01 1.73 1.50 1.31
3.00 3.37 2.77 2.32 1.98 1.71 1.49 1.30
2.50 2.72 2.29 1.95 1.69 1.47 1.29 1.14
2.00 2.67 2.25 1.93 1.67 1.46 1.28 1.14
1.50 3.16 2.62 2.21 1.90 1.65 1.44 1.27
1.00 3.11 2.58 2.18 1.88 1.63 1.43 1.27
0.50 3.07 2.55 2.16 1.86 1.62 1.42 1.26
(m) 0.00 3.76 3.04 2.53 2.14 1.85 1.61 1.42 1.27
-0.50 4.85 3.75 3.02 2.51 2.13 1.84 1.60 1.42
-1.00 6.77 4.86 3.74 3.02 2.51 2.13 1.84 1.61
-1.50 4.87 3.75 3.02 2.51 2.13 1.84
-2.00
-2.50
-3.00
-3.50
-4.00
NOTES Loads refer to the maximum SWL in TONNES for the designated operation without attachments fitted
and assume the load is suspended vertically below the bucket pin.
The weight of bucket, slings/auxillary devices must be deducted from the above loads.
Radius/height is given in METRES measured from slew centre/ground level respectively.
Loads marked 'b' boom and 'a' arm are limited by hydraulic capacity (87% of Maximum System Hydraulic
PAGE 7 of 23 Pressure).
Machine Type Colmar T7000 8485
RCI Serial No CRR624
Equipment 3m57 + 3m10 Tele Dipper 03.12.2009 DPM
3B Op Mode CANTED RAIL FRONT FLOATING END
Sector ± 10° - 45°
UNLOCKED
Dipper EXTENDED Counterweight
Radius (m)
H
e
i
g
h
t
UC Osc. Axle
25 Benson Rd, Nuffield Industrial Estate
Poole, Dorset. BH17 0GB
Tel: 01202 681190
Fax: 01202 677909
E-mail: [email protected]
PROLEC RATED CAPACITY INDICATOR.
PLEASE READ AND UNDERSTAND THE OPERATING
INSTRUCTIONS BEFORE USING THE EQUIPMENT
M/C Serial No.
M/C Plant No.
Compiled
OUT
50 - 150mm
2.50 3.00 3.50 4.00 4.50 5.00 5.50 6.00 6.50 7.00 7.50 8.00
8.00 6.32a
7.50 5.73
7.00 5.49b 4.66
6.50 4.70 3.87
6.00 4.72 3.89 3.26
5.50 4.48a 3.90 3.28 2.78
5.00 4.26a 3.88 3.27 2.79
4.50 4.17a 3.86 3.26 2.79 2.40
4.00 3.71a 4.20a 3.83 3.24 2.77 2.40
3.50 3.33a 3.92a 4.40a 3.79 3.21 2.75 2.39
3.00 3.86a 4.42a 4.51 3.75 3.18 2.73 2.37
2.50 5.39a 4.45 3.71 3.15 2.71 2.36 2.07
2.00 5.38 4.38 3.66 3.11 2.69 2.34 2.07
1.50 6.72 5.29 4.32 3.62 3.08 2.67 2.33
1.00 6.62 5.22 4.27 3.58 3.06 2.65 2.32
0.50 6.55 5.17 4.23 3.55 3.04 2.63 2.32
(m) 0.00 8.71 6.50 5.13 4.20 3.53 3.02 2.63 2.32
-0.50 8.81a 8.68 6.47 5.11 4.18 3.52 3.02 2.63
-1.00 7.02a 9.99 8.67 6.46 5.10 4.18 3.52 3.02
-1.50 9.99 8.69 6.47 5.11 4.19 3.53
-2.00
-2.50
-3.00
-3.50
-4.00
NOTES Loads refer to the maximum SWL in TONNES for the designated operation without attachments fitted
and assume the load is suspended vertically below the bucket pin.
The weight of bucket, slings/auxillary devices must be deducted from the above loads.
Radius/height is given in METRES measured from slew centre/ground level respectively.
Loads marked 'b' boom and 'a' arm are limited by hydraulic capacity (87% of Maximum System Hydraulic
PAGE 8 of 23 Pressure).
Machine Type Colmar T7000 8485
RCI Serial No CRR624
Equipment 3m57 + 3m10 Tele Dipper 03.12.2009 DPM
3B Op Mode CANTED RAIL FRONT FLOATING END
Sector ± 10° - 45°
LOCKED
Dipper EXTENDED Counterweight
Radius (m)
H
e
i
g
h
t
LC Osc. Axle
25 Benson Rd, Nuffield Industrial Estate
Poole, Dorset. BH17 0GB
Tel: 01202 681190
Fax: 01202 677909
E-mail: [email protected]
PROLEC RATED CAPACITY INDICATOR.
PLEASE READ AND UNDERSTAND THE OPERATING
INSTRUCTIONS BEFORE USING THE EQUIPMENT
M/C Serial No.
M/C Plant No.
Compiled
IN
50 - 150mm
2.50 3.00 3.50 4.00 4.50 5.00 5.50 6.00 6.50 7.00 7.50 8.00
8.00 2.77
7.50 2.23
7.00 2.28 1.82
6.50 1.84 1.49
6.00 1.85 1.51 1.23
5.50 1.85 1.51 1.24 1.02
5.00 1.84 1.50 1.24 1.03
4.50 1.82 1.49 1.23 1.03 0.85
4.00 2.22 1.79 1.47 1.22 1.02 0.85
3.50 2.76 2.17 1.75 1.44 1.20 1.01 0.85
3.00 2.68 2.12 1.71 1.41 1.18 0.99 0.84
2.50 2.06 1.67 1.38 1.16 0.98 0.83 0.71
2.00 2.00 1.63 1.35 1.13 0.96 0.82 0.70
1.50 2.44 1.95 1.59 1.32 1.11 0.94 0.81
1.00 2.38 1.90 1.56 1.30 1.09 0.93 0.80
0.50 2.33 1.87 1.53 1.28 1.08 0.92 0.80
(m) 0.00 2.98 2.30 1.84 1.51 1.26 1.07 0.92 0.80
-0.50 4.10 2.96 2.28 1.83 1.50 1.26 1.07 0.92
-1.00 6.41 4.11 2.96 2.28 1.82 1.50 1.25 1.07
-1.50 4.13 2.97 2.28 1.83 1.50 1.26
-2.00
-2.50
-3.00
-3.50
-4.00
NOTES Loads refer to the maximum SWL in TONNES for the designated operation without attachments fitted
and assume the load is suspended vertically below the bucket pin.
The weight of bucket, slings/auxillary devices must be deducted from the above loads.
Radius/height is given in METRES measured from slew centre/ground level respectively.
Loads marked 'b' boom and 'a' arm are limited by hydraulic capacity (87% of Maximum System Hydraulic
PAGE 9 of 23 Pressure).
Machine Type Colmar T7000 8485
RCI Serial No CRR624
Equipment 3m57 + 3m10 Tele Dipper 03.12.2009 DPM
3C Op Mode CANTED RAIL
Sector ± 45° - 135° overside
UNLOCKED
Dipper EXTENDED Counterweight
Radius (m)
H
e
i
g
h
t
U Osc. Axle
25 Benson Rd, Nuffield Industrial Estate
Poole, Dorset. BH17 0GB
Tel: 01202 681190
Fax: 01202 677909
E-mail: [email protected]
PROLEC RATED CAPACITY INDICATOR.
PLEASE READ AND UNDERSTAND THE OPERATING
INSTRUCTIONS BEFORE USING THE EQUIPMENT
M/C Serial No.
M/C Plant No.
Compiled
IN
50 - 150mm
2.50 3.00 3.50 4.00 4.50 5.00 5.50 6.00 6.50 7.00 7.50 8.00
8.00 4.91
7.50 3.99
7.00 4.05 3.29
6.50 3.32 2.75
6.00 3.34 2.77 2.32
5.50 3.33 2.77 2.33 1.97
5.00 3.31 2.76 2.33 1.98
4.50 3.29 2.74 2.31 1.97 1.69
4.00 3.71a 3.25 2.71 2.29 1.96 1.68
3.50 3.33a 3.91 3.20 2.68 2.27 1.94 1.68
3.00 3.86a 3.83 3.15 2.64 2.24 1.92 1.66
2.50 3.75 3.09 2.60 2.21 1.90 1.65 1.44
2.00 3.68 3.04 2.56 2.18 1.88 1.64 1.44
1.50 4.47 3.60 2.99 2.52 2.15 1.86 1.62
1.00 4.38 3.54 2.94 2.48 2.13 1.85 1.61
0.50 4.32 3.50 2.90 2.46 2.11 1.83 1.61
(m) 0.00 5.49 4.27 3.46 2.88 2.44 2.10 1.83 1.61
-0.50 7.49 5.46 4.25 3.44 2.86 2.43 2.09 1.83
-1.00 7.02a 7.49 5.46 4.24 3.43 2.86 2.43 2.10
-1.50 7.52 5.47 4.25 3.44 2.86 2.44
-2.00
-2.50
-3.00
-3.50
-4.00
NOTES Loads refer to the maximum SWL in TONNES for the designated operation without attachments fitted
and assume the load is suspended vertically below the bucket pin.
The weight of bucket, slings/auxillary devices must be deducted from the above loads.
Radius/height is given in METRES measured from slew centre/ground level respectively.
Loads marked 'b' boom and 'a' arm are limited by hydraulic capacity (87% of Maximum System Hydraulic
PAGE 10 of 23 Pressure).
Machine Type Colmar T7000 8485
RCI Serial No CRR624
Equipment 3m57 + 3m10 Tele Dipper 03.12.2009 DPM
3C Op Mode CANTED RAIL
Sector ± 45° - 135° overside
LOCKED
Dipper EXTENDED Counterweight
Radius (m)
H
e
i
g
h
t
L Osc. Axle
25 Benson Rd, Nuffield Industrial Estate
Poole, Dorset. BH17 0GB
Tel: 01202 681190
Fax: 01202 677909
E-mail: [email protected]
PROLEC RATED CAPACITY INDICATOR.
PLEASE READ AND UNDERSTAND THE OPERATING
INSTRUCTIONS BEFORE USING THE EQUIPMENT
M/C Serial No.
M/C Plant No.
Compiled
OUT
50 - 150mm
2.50 3.00 3.50 4.00 4.50 5.00 5.50 6.00 6.50 7.00 7.50 8.00
8.00 5.99
7.50 4.89
7.00 4.95 4.06
6.50 4.09 3.42
6.00 4.11 3.44 2.92
5.50 4.10 3.44 2.93 2.51
5.00 4.09 3.43 2.93 2.52
4.50 4.06 3.41 2.91 2.51 2.18
4.00 3.71a 4.02 3.39 2.89 2.50 2.18
3.50 3.33a 3.92a 3.97 3.35 2.87 2.48 2.17
3.00 3.86a 4.42a 3.92 3.31 2.84 2.46 2.16
2.50 4.65 3.86 3.27 2.81 2.44 2.14 1.89
2.00 4.58 3.81 3.23 2.78 2.42 2.13 1.89
1.50 5.55 4.50 3.76 3.19 2.75 2.40 2.12
1.00 5.46 4.44 3.71 3.16 2.73 2.39 2.11
0.50 5.40 4.40 3.67 3.13 2.71 2.37 2.10
(m) 0.00 6.84 5.35 4.36 3.65 3.11 2.70 2.37 2.10
-0.50 8.81a 6.81 5.33 4.34 3.63 3.10 2.69 2.37
-1.00 7.02a 9.29 6.81 5.32 4.33 3.63 3.10 2.70
-1.50 9.32 6.82 5.33 4.34 3.64 3.11
-2.00
-2.50
-3.00
-3.50
-4.00
NOTES Loads refer to the maximum SWL in TONNES for the designated operation without attachments fitted
and assume the load is suspended vertically below the bucket pin.
The weight of bucket, slings/auxillary devices must be deducted from the above loads.
Radius/height is given in METRES measured from slew centre/ground level respectively.
Loads marked 'b' boom and 'a' arm are limited by hydraulic capacity (87% of Maximum System Hydraulic
PAGE 11 of 23 Pressure).
Machine Type Colmar T7000 8485
RCI Serial No CRR624
Equipment 3m57 + 3m10 Tele Dipper 03.12.2009 DPM
3C Op Mode CANTED RAIL
Sector ± 45° - 135° overside
LOCKED
Dipper EXTENDED Counterweight
Radius (m)
H
e
i
g
h
t
LC Osc. Axle
25 Benson Rd, Nuffield Industrial Estate
Poole, Dorset. BH17 0GB
Tel: 01202 681190
Fax: 01202 677909
E-mail: [email protected]
PROLEC RATED CAPACITY INDICATOR.
PLEASE READ AND UNDERSTAND THE OPERATING
INSTRUCTIONS BEFORE USING THE EQUIPMENT
M/C Serial No.
M/C Plant No.
Compiled
IN
50 - 150mm
2.50 3.00 3.50 4.00 4.50 5.00 5.50 6.00 6.50 7.00 7.50 8.00
8.00 3.70
7.50 3.16 2.67
7.00 2.72 2.34
6.50 2.73 2.36 2.05
6.00 2.37 2.07 1.80
5.50 2.37 2.07 1.82
5.00 2.73 2.36 2.06 1.82 1.60
4.50 2.71 2.35 2.05 1.81 1.61
4.00 2.68 2.33 2.04 1.80 1.60 1.42
3.50 3.09 2.65 2.31 2.02 1.79 1.59 1.42
3.00 3.05 2.62 2.28 2.00 1.78 1.58 1.42
2.50 3.00 2.58 2.25 1.98 1.76 1.57 1.41
2.00 2.95 2.55 2.22 1.96 1.74 1.56 1.40
1.50 2.90 2.51 2.20 1.94 1.73 1.55 1.40
1.00 2.86 2.48 2.18 1.93 1.72 1.54 1.40
0.50 3.32 2.83 2.46 2.16 1.91 1.71 1.54 1.40
(m) 0.00 3.94 3.29 2.81 2.44 2.14 1.90 1.70 1.53
-0.50 4.84 3.92 3.28 2.80 2.43 2.14 1.90 1.70 1.54
-1.00 4.84 3.92 3.28 2.80 2.43 2.14 1.90 1.70
-1.50 3.93 3.28 2.80 2.43 2.14 1.91
-2.00
-2.50
-3.00
-3.50
-4.00
NOTES Loads refer to the maximum SWL in TONNES for the designated operation without attachments fitted
and assume the load is suspended vertically below the bucket pin.
The weight of bucket, slings/auxillary devices must be deducted from the above loads.
Radius/height is given in METRES measured from slew centre/ground level respectively.
Loads marked 'b' boom and 'a' arm are limited by hydraulic capacity (87% of Maximum System Hydraulic
PAGE 12 of 23 Pressure).
Machine Type Colmar T7000 8485
RCI Serial No CRR624
Equipment 3m57 + 3m10 Tele Dipper 03.12.2009 DPM
3D Op Mode CANTED RAIL FIXED REAR END
Sector ± 135° - 150° over rear
UNLOCKED
Dipper EXTENDED Counterweight
Radius (m)
H
e
i
g
h
t
U Osc. Axle
25 Benson Rd, Nuffield Industrial Estate
Poole, Dorset. BH17 0GB
Tel: 01202 681190
Fax: 01202 677909
E-mail: [email protected]
PROLEC RATED CAPACITY INDICATOR.
PLEASE READ AND UNDERSTAND THE OPERATING
INSTRUCTIONS BEFORE USING THE EQUIPMENT
M/C Serial No.
M/C Plant No.
Compiled
IN
50 - 150mm
2.50 3.00 3.50 4.00 4.50 5.00 5.50 6.00 6.50 7.00 7.50 8.00
8.00 5.97
7.50 5.12 4.41
7.00 4.45 3.88
6.50 4.47 3.91 3.44
6.00 3.92 3.46 3.07
5.50 3.92 3.47 3.09
5.00 4.04a 3.91 3.46 3.09 2.77
4.50 3.91a 3.89 3.45 3.08 2.77
4.00 3.93a 3.87 3.43 3.07 2.76 2.49
3.50 3.60a 4.14a 3.85 3.41 3.06 2.75 2.49
3.00 4.12a 4.34 3.82 3.39 3.04 2.74 2.49
2.50 4.95 4.30 3.79 3.37 3.02 2.73 2.48
2.00 4.89 4.26 3.76 3.35 3.01 2.72 2.47
1.50 4.84 4.22 3.73 3.32 2.99 2.71 2.47
1.00 4.80 4.19 3.70 3.31 2.98 2.70 2.46
0.50 5.54 4.76 4.16 3.68 3.29 2.96 2.69 2.46
(m) 0.00 6.55 5.51 4.74 4.14 3.67 3.28 2.96 2.69
-0.50 6.65a 6.53 5.50 4.73 4.13 3.66 3.27 2.96 2.69
-1.00 8.01 6.53 5.50 4.72 4.13 3.66 3.27 2.96
-1.50 6.54 5.50 4.73 4.13 3.66 3.28
-2.00
-2.50
-3.00
-3.50
-4.00
NOTES Loads refer to the maximum SWL in TONNES for the designated operation without attachments fitted
and assume the load is suspended vertically below the bucket pin.
The weight of bucket, slings/auxillary devices must be deducted from the above loads.
Radius/height is given in METRES measured from slew centre/ground level respectively.
Loads marked 'b' boom and 'a' arm are limited by hydraulic capacity (87% of Maximum System Hydraulic
PAGE 13 of 23 Pressure).
Machine Type Colmar T7000 8485
RCI Serial No CRR624
Equipment 3m57 + 3m10 Tele Dipper 03.12.2009 DPM
3D Op Mode CANTED RAIL FIXED REAR END
Sector ± 135° - 150° over rear
LOCKED
Dipper EXTENDED Counterweight
Radius (m)
H
e
i
g
h
t
L Osc. Axle
25 Benson Rd, Nuffield Industrial Estate
Poole, Dorset. BH17 0GB
Tel: 01202 681190
Fax: 01202 677909
E-mail: [email protected]
PROLEC RATED CAPACITY INDICATOR.
PLEASE READ AND UNDERSTAND THE OPERATING
INSTRUCTIONS BEFORE USING THE EQUIPMENT
M/C Serial No.
M/C Plant No.
Compiled
OUT
50 - 150mm
2.50 3.00 3.50 4.00 4.50 5.00 5.50 6.00 6.50 7.00 7.50 8.00
8.00 4.09
7.50 3.50 2.98
7.00 3.02 2.61
6.50 3.04 2.63 2.30
6.00 2.64 2.31 2.03
5.50 2.64 2.32 2.04
5.00 3.03 2.63 2.31 2.04 1.81
4.50 3.01 2.62 2.30 2.04 1.81
4.00 2.99 2.60 2.29 2.03 1.81 1.62
3.50 3.43 2.96 2.58 2.27 2.02 1.80 1.62
3.00 3.39 2.92 2.55 2.25 2.00 1.79 1.61
2.50 3.34 2.89 2.53 2.23 1.99 1.78 1.60
2.00 3.29 2.85 2.50 2.21 1.97 1.77 1.60
1.50 3.24 2.82 2.47 2.19 1.96 1.76 1.59
1.00 3.21 2.79 2.45 2.17 1.94 1.75 1.59
0.50 3.71 3.18 2.76 2.43 2.16 1.93 1.75 1.59
(m) 0.00 4.40 3.69 3.16 2.75 2.42 2.15 1.93 1.74
-0.50 5.40 4.39 3.67 3.15 2.74 2.41 2.15 1.93 1.75
-1.00 5.40 4.39 3.67 3.14 2.73 2.41 2.15 1.93
-1.50 4.39 3.68 3.15 2.74 2.41 2.15
-2.00
-2.50
-3.00
-3.50
-4.00
NOTES Loads refer to the maximum SWL in TONNES for the designated operation without attachments fitted
and assume the load is suspended vertically below the bucket pin.
The weight of bucket, slings/auxillary devices must be deducted from the above loads.
Radius/height is given in METRES measured from slew centre/ground level respectively.
Loads marked 'b' boom and 'a' arm are limited by hydraulic capacity (87% of Maximum System Hydraulic
PAGE 14 of 23 Pressure).
Machine Type Colmar T7000 8485
RCI Serial No CRR624
Equipment 3m57 + 3m10 Tele Dipper 03.12.2009 DPM
3D Op Mode CANTED RAIL FIXED REAR END
Sector ± 135° - 150° over rear
UNLOCKED
Dipper EXTENDED Counterweight
Radius (m)
H
e
i
g
h
t
UC Osc. Axle
25 Benson Rd, Nuffield Industrial Estate
Poole, Dorset. BH17 0GB
Tel: 01202 681190
Fax: 01202 677909
E-mail: [email protected]
PROLEC RATED CAPACITY INDICATOR.
PLEASE READ AND UNDERSTAND THE OPERATING
INSTRUCTIONS BEFORE USING THE EQUIPMENT
M/C Serial No.
M/C Plant No.
Compiled
OUT
50 - 150mm
2.50 3.00 3.50 4.00 4.50 5.00 5.50 6.00 6.50 7.00 7.50 8.00
8.00 6.73
7.50 5.79 4.99
7.00 5.04 4.41
6.50 5.05a 4.44 3.92
6.00 4.45 3.94 3.51
5.50 4.45 3.94 3.52
5.00 4.04a 4.43a 3.94 3.52 3.17
4.50 3.91a 4.34a 3.93 3.52 3.17
4.00 3.93a 4.38a 3.91 3.51 3.17 2.87
3.50 3.60a 4.14a 4.38 3.89 3.49 3.16 2.87
3.00 4.12a 4.62a 4.35 3.87 3.48 3.15 2.86
2.50 5.24a 4.89 4.32 3.85 3.46 3.13 2.85
2.00 5.55 4.85 4.29 3.83 3.44 3.12 2.85
1.50 5.50 4.81 4.26 3.80 3.43 3.11 2.84
1.00 5.46 4.78 4.23 3.78 3.41 3.10 2.84
0.50 6.30 5.43 4.75 4.21 3.77 3.40 3.09 2.84
(m) 0.00 7.44 6.27 5.41 4.73 4.20 3.76 3.40 3.09
-0.50 6.65a 7.43 6.26 5.39 4.72 4.19 3.75 3.39 3.10
-1.00 8.29a 7.43 6.26 5.39 4.72 4.19 3.75 3.40
-1.50 7.44 6.26 5.39 4.72 4.19 3.76
-2.00
-2.50
-3.00
-3.50
-4.00
NOTES Loads refer to the maximum SWL in TONNES for the designated operation without attachments fitted
and assume the load is suspended vertically below the bucket pin.
The weight of bucket, slings/auxillary devices must be deducted from the above loads.
Radius/height is given in METRES measured from slew centre/ground level respectively.
Loads marked 'b' boom and 'a' arm are limited by hydraulic capacity (87% of Maximum System Hydraulic
PAGE 15 of 23 Pressure).
Machine Type Colmar T7000 8485
RCI Serial No CRR624
Equipment 3m57 + 3m10 Tele Dipper 03.12.2009 DPM
3D Op Mode CANTED RAIL FIXED REAR END
Sector ± 135° - 150° over rear
LOCKED
Dipper EXTENDED Counterweight
Radius (m)
H
e
i
g
h
t
LC Osc. Axle
25 Benson Rd, Nuffield Industrial Estate
Poole, Dorset. BH17 0GB
Tel: 01202 681190
Fax: 01202 677909
E-mail: [email protected]
PROLEC RATED CAPACITY INDICATOR.
PLEASE READ AND UNDERSTAND THE OPERATING
INSTRUCTIONS BEFORE USING THE EQUIPMENT
M/C Serial No.
M/C Plant No.
Compiled
IN
50 - 150mm
2.50 3.00 3.50 4.00 4.50 5.00 5.50 6.00 6.50 7.00 7.50 8.00
8.00 5.15
7.50 4.40 3.76
7.00 3.81 3.30
6.50 3.83 3.33 2.92
6.00 3.34 2.94 2.60
5.50 3.34 2.94 2.61
5.00 3.82 3.33 2.94 2.61 2.33
4.50 3.80 3.32 2.93 2.60 2.33
4.00 3.77 3.30 2.91 2.59 2.33 2.09
3.50 3.60a 3.74 3.27 2.89 2.58 2.32 2.09
3.00 4.12a 3.71 3.25 2.87 2.57 2.31 2.09
2.50 4.24 3.67 3.22 2.85 2.55 2.30 2.08
2.00 4.19 3.63 3.19 2.83 2.54 2.29 2.07
1.50 4.14 3.60 3.16 2.81 2.52 2.28 2.07
1.00 4.10 3.57 3.14 2.80 2.51 2.27 2.07
0.50 4.76 4.07 3.54 3.12 2.78 2.50 2.26 2.07
(m) 0.00 5.65 4.73 4.05 3.53 3.11 2.77 2.49 2.26
-0.50 6.65a 5.64 4.72 4.04 3.52 3.10 2.77 2.49 2.26
-1.00 6.97 5.64 4.71 4.03 3.51 3.10 2.77 2.50
-1.50 5.65 4.72 4.04 3.52 3.11 2.78
-2.00
-2.50
-3.00
-3.50
-4.00
NOTES Loads refer to the maximum SWL in TONNES for the designated operation without attachments fitted
and assume the load is suspended vertically below the bucket pin.
The weight of bucket, slings/auxillary devices must be deducted from the above loads.
Radius/height is given in METRES measured from slew centre/ground level respectively.
Loads marked 'b' boom and 'a' arm are limited by hydraulic capacity (87% of Maximum System Hydraulic
PAGE 16 of 23 Pressure).
Machine Type Colmar T7000 8485
RCI Serial No CRR624
Equipment 3m57 + 3m10 Tele Dipper 03.12.2009 DPM
3E Op Mode CANTED RAIL FIXED REAR END
Sector ± 150° - 160° over rear
Radius (m)
H
e
i
g
h
t
U Osc. Axle UNLOCKED
Dipper EXTENDED Counterweight
25 Benson Rd, Nuffield Industrial Estate
Poole, Dorset. BH17 0GB
Tel: 01202 681190
Fax: 01202 677909
E-mail: [email protected]
PROLEC RATED CAPACITY INDICATOR.
PLEASE READ AND UNDERSTAND THE OPERATING
INSTRUCTIONS BEFORE USING THE EQUIPMENT
M/C Serial No.
M/C Plant No.
Compiled
IN
50 - 150mm
2.50 3.00 3.50 4.00 4.50 5.00 5.50 6.00 6.50 7.00 7.50 8.00
8.00 6.94a
7.50 6.06b 5.53a
7.00 5.52a 5.22a
6.50 5.05a 5.20a 4.83a
6.00 4.89a 5.00a 4.18a
5.50 4.62a 4.86a 4.77
5.00 4.04a 4.43a 4.74a 4.77 4.26a
4.50 3.91a 4.34a 4.69a 4.76 4.30
4.00 3.93a 4.38a 4.73a 4.75 4.29 3.29a
3.50 3.60a 4.14a 4.58a 4.91a 4.73 4.28 3.89
3.00 4.12a 4.62a 4.98a 5.23a 4.71 4.27 3.88
2.50 5.24a 5.49a 5.66a 5.22 4.69 4.25 3.88
2.00 7.52a 6.59 5.82 5.19 4.67 4.24 3.87
1.50 7.49 6.54 5.78 5.16 4.65 4.22 3.86
1.00 7.44 6.50 5.75 5.14 4.64 4.21 3.85
0.50 8.61 7.40 6.47 5.73 5.12 4.62 4.20 3.86
(m) 0.00 9.99 8.58 7.37 6.44 5.71 5.11 4.61 4.20
-0.50 6.65a 9.99 8.56 7.36 6.43 5.70 5.10 4.61 4.21
-1.00 8.29a 9.99 8.56 7.35 6.43 5.69 5.10 4.62
-1.50 9.99 8.57 7.36 6.43 5.70 5.11
-2.00
-2.50
-3.00
-3.50
-4.00
NOTES Loads refer to the maximum SWL in TONNES for the designated operation without attachments fitted
and assume the load is suspended vertically below the bucket pin.
The weight of bucket, slings/auxillary devices must be deducted from the above loads.
Radius/height is given in METRES measured from slew centre/ground level respectively.
Loads marked 'b' boom and 'a' arm are limited by hydraulic capacity (87% of Maximum System Hydraulic
PAGE 17 of 23 Pressure).
Machine Type Colmar T7000 8485
RCI Serial No CRR624
Equipment 3m57 + 3m10 Tele Dipper 03.12.2009 DPM
3E Op Mode CANTED RAIL FIXED REAR END
Sector ± 150° - 160° over rear
Radius (m)
H
e
i
g
h
t
L Osc. Axle LOCKED
Dipper EXTENDED Counterweight
25 Benson Rd, Nuffield Industrial Estate
Poole, Dorset. BH17 0GB
Tel: 01202 681190
Fax: 01202 677909
E-mail: [email protected]
PROLEC RATED CAPACITY INDICATOR.
PLEASE READ AND UNDERSTAND THE OPERATING
INSTRUCTIONS BEFORE USING THE EQUIPMENT
M/C Serial No.
M/C Plant No.
Compiled
OUT
50 - 150mm
2.50 3.00 3.50 4.00 4.50 5.00 5.50 6.00 6.50 7.00 7.50 8.00
8.00 5.70
7.50 4.88 4.19
7.00 4.23 3.68
6.50 4.25 3.71 3.26
6.00 3.72 3.28 2.91
5.50 3.72 3.28 2.92
5.00 4.04a 3.71 3.28 2.92 2.62
4.50 3.91a 3.70 3.27 2.92 2.62
4.00 3.93a 3.68 3.26 2.91 2.62 2.36
3.50 3.60a 4.14a 3.65 3.24 2.90 2.61 2.36
3.00 4.12a 4.13 3.63 3.22 2.88 2.60 2.36
2.50 4.72 4.09 3.60 3.20 2.87 2.59 2.35
2.00 4.67 4.05 3.57 3.18 2.85 2.58 2.34
1.50 4.62 4.02 3.54 3.16 2.84 2.57 2.34
1.00 4.58 3.99 3.52 3.14 2.82 2.56 2.33
0.50 5.31 4.55 3.97 3.50 3.13 2.81 2.55 2.33
(m) 0.00 6.30 5.28 4.53 3.95 3.49 3.12 2.81 2.55
-0.50 6.65a 6.29 5.27 4.52 3.94 3.48 3.11 2.80 2.55
-1.00 7.77 6.29 5.27 4.51 3.94 3.48 3.11 2.81
-1.50 6.30 5.27 4.52 3.94 3.48 3.12
-2.00
-2.50
-3.00
-3.50
-4.00
NOTES Loads refer to the maximum SWL in TONNES for the designated operation without attachments fitted
and assume the load is suspended vertically below the bucket pin.
The weight of bucket, slings/auxillary devices must be deducted from the above loads.
Radius/height is given in METRES measured from slew centre/ground level respectively.
Loads marked 'b' boom and 'a' arm are limited by hydraulic capacity (87% of Maximum System Hydraulic
PAGE 18 of 23 Pressure).
Machine Type Colmar T7000 8485
RCI Serial No CRR624
Equipment 3m57 + 3m10 Tele Dipper 03.12.2009 DPM
3E Op Mode CANTED RAIL FIXED REAR END
Sector ± 150° - 160° over rear
Radius (m)
H
e
i
g
h
t
UC Osc. Axle UNLOCKED
Dipper EXTENDED Counterweight
25 Benson Rd, Nuffield Industrial Estate
Poole, Dorset. BH17 0GB
Tel: 01202 681190
Fax: 01202 677909
E-mail: [email protected]
PROLEC RATED CAPACITY INDICATOR.
PLEASE READ AND UNDERSTAND THE OPERATING
INSTRUCTIONS BEFORE USING THE EQUIPMENT
M/C Serial No.
M/C Plant No.
Compiled
OUT
50 - 150mm
2.50 3.00 3.50 4.00 4.50 5.00 5.50 6.00 6.50 7.00 7.50 8.00
8.00 6.94a
7.50 6.06b 5.53a
7.00 5.52a 5.22a
6.50 5.05a 5.20a 4.83a
6.00 4.89a 5.00a 4.18a
5.50 4.62a 4.86a 4.79a
5.00 4.04a 4.43a 4.74a 4.86a 4.26a
4.50 3.91a 4.34a 4.69a 4.87a 4.49
4.00 3.93a 4.38a 4.73a 4.94a 4.49 3.29a
3.50 3.60a 4.14a 4.58a 4.91a 4.95 4.47 4.07
3.00 4.12a 4.62a 4.98a 5.23a 4.93 4.46 4.06
2.50 5.24a 5.49a 5.66a 5.45 4.90 4.45 4.06
2.00 7.52a 6.87 6.07 5.42 4.88 4.43 4.05
1.50 7.82 6.82 6.04 5.39 4.86 4.42 4.04
1.00 7.76 6.78 6.00 5.37 4.85 4.41 4.03
0.50 8.98 7.72 6.75 5.98 5.35 4.83 4.40 3.97a
(m) 0.00 9.99 8.95 7.70 6.73 5.96 5.34 4.83 4.40
-0.50 6.65a 9.99 8.93 7.68 6.71 5.95 5.33 4.82 4.40
-1.00 8.29a 9.99 8.93 7.67 6.71 5.95 5.33 4.83
-1.50 9.99 8.94 7.68 6.72 5.96 5.34
-2.00
-2.50
-3.00
-3.50
-4.00
NOTES Loads refer to the maximum SWL in TONNES for the designated operation without attachments fitted
and assume the load is suspended vertically below the bucket pin.
The weight of bucket, slings/auxillary devices must be deducted from the above loads.
Radius/height is given in METRES measured from slew centre/ground level respectively.
Loads marked 'b' boom and 'a' arm are limited by hydraulic capacity (87% of Maximum System Hydraulic
PAGE 19 of 23 Pressure).
Machine Type Colmar T7000 8485
RCI Serial No CRR624
Equipment 3m57 + 3m10 Tele Dipper 03.12.2009 DPM
3E Op Mode CANTED RAIL FIXED REAR END
Sector ± 150° - 160° over rear
Radius (m)
H
e
i
g
h
t
LC Osc. Axle LOCKED
Dipper EXTENDED Counterweight
25 Benson Rd, Nuffield Industrial Estate
Poole, Dorset. BH17 0GB
Tel: 01202 681190
Fax: 01202 677909
E-mail: [email protected]
PROLEC RATED CAPACITY INDICATOR.
PLEASE READ AND UNDERSTAND THE OPERATING
INSTRUCTIONS BEFORE USING THE EQUIPMENT
M/C Serial No.
M/C Plant No.
Compiled
IN
50 - 150mm
2.50 3.00 3.50 4.00 4.50 5.00 5.50 6.00 6.50 7.00 7.50 8.00
8.00 6.94a
7.50 6.06b 5.53a
7.00 5.52a 5.22a
6.50 5.05a 5.20a 4.83a
6.00 4.89a 5.00a 4.18a
5.50 4.62a 4.86a 4.79a
5.00 4.04a 4.43a 4.74a 4.86a 4.26a
4.50 3.91a 4.34a 4.69a 4.87a 4.43
4.00 3.93a 4.38a 4.73a 4.87 4.42 3.29a
3.50 3.60a 4.14a 4.58a 4.91a 4.86 4.42 4.04
3.00 4.12a 4.62a 4.98a 5.23a 4.85 4.41 4.03
2.50 5.24a 5.49a 5.66a 5.35 4.83 4.39 4.02
2.00 7.52a 6.70 5.94 5.33 4.81 4.38 4.02
1.50 7.62 6.67 5.92 5.31 4.80 4.37 4.01
1.00 7.58 6.64 5.89 5.29 4.79 4.36 4.01
0.50 8.76 7.55 6.62 5.88 5.27 4.78 4.36 3.97a
(m) 0.00 9.99 8.73 7.53 6.60 5.86 5.26 4.77 4.36
-0.50 6.65a 9.99 8.72 7.51 6.59 5.85 5.26 4.77 4.36
-1.00 8.29a 9.99 8.72 7.51 6.58 5.85 5.26 4.77
-1.50 9.99 8.72 7.51 6.59 5.86 5.27
-2.00
-2.50
-3.00
-3.50
-4.00
NOTES Loads refer to the maximum SWL in TONNES for the designated operation without attachments fitted
and assume the load is suspended vertically below the bucket pin.
The weight of bucket, slings/auxillary devices must be deducted from the above loads.
Radius/height is given in METRES measured from slew centre/ground level respectively.
Loads marked 'b' boom and 'a' arm are limited by hydraulic capacity (87% of Maximum System Hydraulic
PAGE 20 of 23 Pressure).
Machine Type Colmar T7000 8485
RCI Serial No CRR624
Equipment 3m57 + 3m10 Tele Dipper 03.12.2009 DPM
3F Op Mode CANTED RAIL FIXED REAR END
Sector ± 160° - 180° over rear
Radius (m)
H
e
i
g
h
t
U Osc. Axle UNLOCKED
Dipper EXTENDED Counterweight
25 Benson Rd, Nuffield Industrial Estate
Poole, Dorset. BH17 0GB
Tel: 01202 681190
Fax: 01202 677909
E-mail: [email protected]
PROLEC RATED CAPACITY INDICATOR.
PLEASE READ AND UNDERSTAND THE OPERATING
INSTRUCTIONS BEFORE USING THE EQUIPMENT
M/C Serial No.
M/C Plant No.
Compiled
IN
50 - 150mm
2.50 3.00 3.50 4.00 4.50 5.00 5.50 6.00 6.50 7.00 7.50 8.00
8.00 6.94a
7.50 6.06b 5.53a
7.00 5.52a 5.22a
6.50 5.05a 5.20a 4.83a
6.00 4.89a 5.00a 4.18a
5.50 4.62a 4.86a 4.79a
5.00 4.04a 4.43a 4.74a 4.86a 4.26a
4.50 3.91a 4.34a 4.69a 4.87a 4.68a
4.00 3.93a 4.38a 4.73a 4.94a 4.86a 3.29a
3.50 3.60a 4.14a 4.58a 4.91a 5.09a 5.03 4.15a
3.00 4.12a 4.62a 4.98a 5.23a 5.35a 5.01 4.50a
2.50 5.24a 5.49a 5.66a 5.74a 5.58 4.99 4.51
2.00 7.52a 6.97a 6.68a 6.27 5.56 4.98 4.50
1.50 9.72 8.23 7.11 6.23 5.53 4.96 4.49
1.00 9.65 8.18 7.07 6.21 5.51 4.95 4.48
0.50 9.99 9.60 8.14 7.04 6.18 5.50 4.94 3.97a
(m) 0.00 9.99 9.99 9.57 8.11 7.02 6.17 5.49 4.94
-0.50 6.65a 9.99 9.99 9.55 8.10 7.01 6.16 5.49 4.94
-1.00 8.29a 9.99 9.99 9.54 8.09 7.00 6.16 5.49
-1.50 9.99 9.99 9.55 8.10 7.01 6.17
-2.00
-2.50
-3.00
-3.50
-4.00
NOTES Loads refer to the maximum SWL in TONNES for the designated operation without attachments fitted
and assume the load is suspended vertically below the bucket pin.
The weight of bucket, slings/auxillary devices must be deducted from the above loads.
Radius/height is given in METRES measured from slew centre/ground level respectively.
Loads marked 'b' boom and 'a' arm are limited by hydraulic capacity (87% of Maximum System Hydraulic
PAGE 21 of 23 Pressure).
Machine Type Colmar T7000 8485
RCI Serial No CRR624
Equipment 3m57 + 3m10 Tele Dipper 03.12.2009 DPM
3F Op Mode CANTED RAIL FIXED REAR END
Sector ± 160° - 180° over rear
Radius (m)
H
e
i
g
h
t
L Osc. Axle LOCKED
Dipper EXTENDED Counterweight
25 Benson Rd, Nuffield Industrial Estate
Poole, Dorset. BH17 0GB
Tel: 01202 681190
Fax: 01202 677909
E-mail: [email protected]
PROLEC RATED CAPACITY INDICATOR.
PLEASE READ AND UNDERSTAND THE OPERATING
INSTRUCTIONS BEFORE USING THE EQUIPMENT
M/C Serial No.
M/C Plant No.
Compiled
OUT
50 - 150mm
2.50 3.00 3.50 4.00 4.50 5.00 5.50 6.00 6.50 7.00 7.50 8.00
8.00 6.94a
7.50 6.06b 5.53a
7.00 5.52a 5.22a
6.50 5.05a 5.20a 4.83a
6.00 4.89a 5.00a 4.18a
5.50 4.62a 4.86a 4.79a
5.00 4.04a 4.43a 4.74a 4.86a 4.26a
4.50 3.91a 4.34a 4.69a 4.87a 4.43
4.00 3.93a 4.38a 4.73a 4.87 4.42 3.29a
3.50 3.60a 4.14a 4.58a 4.91a 4.86 4.42 4.04
3.00 4.12a 4.62a 4.98a 5.23a 4.85 4.41 4.03
2.50 5.24a 5.49a 5.66a 5.35 4.83 4.39 4.02
2.00 7.52a 6.70 5.94 5.33 4.81 4.38 4.02
1.50 7.62 6.67 5.92 5.31 4.80 4.37 4.01
1.00 7.58 6.64 5.89 5.29 4.79 4.36 4.01
0.50 8.76 7.55 6.62 5.88 5.27 4.78 4.36 3.97a
(m) 0.00 9.99 8.73 7.53 6.60 5.86 5.26 4.77 4.36
-0.50 6.65a 9.99 8.72 7.51 6.59 5.85 5.26 4.77 4.36
-1.00 8.29a 9.99 8.72 7.51 6.58 5.85 5.26 4.77
-1.50 9.99 8.72 7.51 6.59 5.86 5.27
-2.00
-2.50
-3.00
-3.50
-4.00
NOTES Loads refer to the maximum SWL in TONNES for the designated operation without attachments fitted
and assume the load is suspended vertically below the bucket pin.
The weight of bucket, slings/auxillary devices must be deducted from the above loads.
Radius/height is given in METRES measured from slew centre/ground level respectively.
Loads marked 'b' boom and 'a' arm are limited by hydraulic capacity (87% of Maximum System Hydraulic
PAGE 22 of 23 Pressure).
Machine Type Colmar T7000 8485
RCI Serial No CRR624
Equipment 3m57 + 3m10 Tele Dipper 03.12.2009 DPM
3F Op Mode CANTED RAIL FIXED REAR END
Sector ± 160° - 180° over rear
Radius (m)
H
e
i
g
h
t
UC Osc. Axle UNLOCKED
Dipper EXTENDED Counterweight
25 Benson Rd, Nuffield Industrial Estate
Poole, Dorset. BH17 0GB
Tel: 01202 681190
Fax: 01202 677909
E-mail: [email protected]
PROLEC RATED CAPACITY INDICATOR.
PLEASE READ AND UNDERSTAND THE OPERATING
INSTRUCTIONS BEFORE USING THE EQUIPMENT
M/C Serial No.
M/C Plant No.
Compiled
OUT
50 - 150mm
2.50 3.00 3.50 4.00 4.50 5.00 5.50 6.00 6.50 7.00 7.50 8.00
8.00 6.94a
7.50 6.06b 5.53a
7.00 5.52a 5.22a
6.50 5.05a 5.20a 4.83a
6.00 4.89a 5.00a 4.18a
5.50 4.62a 4.86a 4.79a
5.00 4.04a 4.43a 4.74a 4.86a 4.26a
4.50 3.91a 4.34a 4.69a 4.87a 4.68a
4.00 3.93a 4.38a 4.73a 4.94a 4.86a 3.29a
3.50 3.60a 4.14a 4.58a 4.91a 5.09a 5.03 4.15a
3.00 4.12a 4.62a 4.98a 5.23a 5.35a 5.01 4.50a
2.50 5.24a 5.49a 5.66a 5.74a 5.58 4.99 4.51
2.00 7.52a 6.97a 6.68a 6.27 5.56 4.98 4.50
1.50 9.72 8.23 7.11 6.23 5.53 4.96 4.49
1.00 9.65 8.18 7.07 6.21 5.51 4.95 4.48
0.50 9.99 9.60 8.14 7.04 6.18 5.50 4.94 3.97a
(m) 0.00 9.99 9.99 9.57 8.11 7.02 6.17 5.49 4.94
-0.50 6.65a 9.99 9.99 9.55 8.10 7.01 6.16 5.49 4.94
-1.00 8.29a 9.99 9.99 9.54 8.09 7.00 6.16 5.49
-1.50 9.99 9.99 9.55 8.10 7.01 6.17
-2.00
-2.50
-3.00
-3.50
-4.00
NOTES Loads refer to the maximum SWL in TONNES for the designated operation without attachments fitted
and assume the load is suspended vertically below the bucket pin.
The weight of bucket, slings/auxillary devices must be deducted from the above loads.
Radius/height is given in METRES measured from slew centre/ground level respectively.
Loads marked 'b' boom and 'a' arm are limited by hydraulic capacity (87% of Maximum System Hydraulic
PAGE 23 of 23 Pressure).
Machine Type Colmar T7000 8485
RCI Serial No CRR624
Equipment 3m57 + 3m10 Tele Dipper 03.12.2009 DPM
3F Op Mode CANTED RAIL FIXED REAR END
Sector ± 160° - 180° over rear
Radius (m)
H
e
i
g
h
t
LC Osc. Axle LOCKED
Dipper EXTENDED Counterweight
