“PROTECTA” Door Barrier

MODEL NO: 320

w w w . i n f a - s e c u r e . c o m . a u

ASSEMBLY INSTRUCTIONS

INFA SECURE PTY LTD

P.O. Box 487, Emu Plains NSW 2750

SERVICE NUMBER:

(02) 4728 8090

INDEX

I. Parts list for Door Barrier P 1

II. Door Barrier assembly instructions P 1 - 2

III. Methods of installing wall cups P 3

IV. Operating instructions P 3

V. Extension assembly instructions P 4

VI. How to release tube inserts P 4

VII. Safety notes & warnings P 5

IMPORTANT NOTESREAD THIS CAREFULLY BEFORE INSTALLATION OF DOOR BARRIER

1 THE THREADED ROD (A) IS DESIGNED TO SLIDE FREELY INSIDE THE TUBE INSERTS (J). THE THREAD IS ONLY ACTIVE WHENADJUSTING WINDER KNOBS.

2 THE TWO MAIN FRAME UPRIGHTS (E) WILL ALSO HAVE ASLIGHT OUTWARDS POSITION BEFORE BEING PLACED INPOSITION. THIS IS DESIGNED TO GIVE REQUIRED TENSIONWHEN IN POSITION.

“PROTECTA” Door Barrier #320 & Extensions #321/322/323/324/325/327 Manual

I. PARTS LIST FOR DOOR BARRIER

A) Threaded Pressure Pad 4PCS/Set

B) Winder Knob 4PCS/Set

C) Second Lock 1PCS/Set

D) Lever Handle 1PCS/Set

E) Door Barrier Body 1PCS/Set J) Small Tube Insert 4PCS/Set

G) Cup 4PCS/Set

H) Screw (To assemble G) 4PCS/Set

A) Threaded Pressure Pad 4PCS/Set

I) Locking Support Panel (Combined with E)

II. DOOR BARRIER ASSEMBLY INSTRUCTIONS

Step 1: Take the Door Barrier out of the carton. Remove the plastic bag.Step 2: Insert 4 (J) into the ends of the tubes.: Step 3: Place the threaded pressure pads (A) into the hole on each corner of the Door Barrier

A

B

C

D I

E

FJ

J

GH

E

J

J

1.

Step 4: Before installing the door barrier, measure the distance between the two surfaces to ensure that the Door Barrier is the correct width for the opening.

Maximum measurement is 820mm

If you find the measurement exceeds 820mm then two options need to be considered.

A) Use a ‘Protecta’ extension kit as illustrated in this leaflet (80, 140, 280, 490, 980 or 1490mm). Refer to section “Method of Attaching Extensions” before proceeding to Step 5.

B) Securely fit a wooden spacer on the wall side to fill the void.

IMPORTANT: IT IS VERY IMPORTANT FOR YOUR BABY’S SAFETY THAT THE MEASUREMENT BETWEEN THE OUTSIDE FRAME AND THE SURFACE WHERE THE DOOR BARRIER IS BEING PLACED DOES NOT EXCEED 65 MM. CHECK EACH SIDE. REFER TO FIGURE 2

Figure 2

IMPORTANT NOTE: WALL CAPS (G) ARE ALWAYS RECOMMENDED TO BE USED FOR INCREASED SAFETY. ESPECIALLY WHEN THE WALL SURFACE HAS

A SMOOTH FINISH IE, METAL SURFACES, HIGH-GLOSS PAINT ETC.

See next page ‘Methods of Installing Wall Cups’.

Step 5:

Step 6:

65mm65mm

2.

Place the Door Barrier in decided location, using your fingers, slide out the bottom threaded pressure pads (A) until they touch the wall surface and then tighten with winder knob (B) so the rubber pressure pad is firmly against the wall surfaces on each side. Ensure even measurement on both sides.

NOTE: Refer to important note on Index page.

Proceed to the top of the Door Barrier and slide out the threaded pressure pads (as in Step 5). With the leaver handle down, ensure the top of the rectangular metal upright (J) is located in recessed section of the lever handle (D). The metal upright should be almost touching the back of the recessed section. Remove the binding straps (H).

Important Safety Checks

1).

2).

3).

CHECK THE DOOR BARRIER IS FIRM AND SECURELY FITTEDAGAINST THE WALL SURFACES. IF YOU FIND THE BARRIERMOVES ON THE SURFACES, THE PLASTIC CUPS (G) MUST BE USED.(AT THE TOP OF STAIRS OR IF USED ON AN EXTERIOR DOOR WERECOMMEND ONLY TO USE THE WALL CUPS).

REFER TO SECTION “FITTING WALL CUPS” BELOW

ALWAYS CHECK THE 65mm MEASUREMENT IN “IMPORTANT” INSTEP 4 IS ADHERED TO.

CHECK THAT THE DOOR BARRIER IS SITTING FIRMLY AGAINST THE SURFACE (RIGHT DOWN AGAINST THE FLOOR).

III. METHODS OF INSTALLING WALL CUPS

IV. OPERATING INSTRUCTIONSOPEN:Step 1: Push the safety button in and lift the handle

in the direction shown as arrow (1) Step 2: Lift the gate as arrow (2)Step 3: Pull/push the door open

CLOSE:Step 1: Lift up the gate (D) and swing close. Once

the gate is aligned correctly over the frame,lower in position

Step 2: Push the lever handle (D) downward untilthe safety button locks into position.

2

SafetyButton1

3.

Reverse Step 5 and 6 on previous page and place cups (G) on the end of the rubber pressure pads. Wind the winder knobs until they push the cups against the wall surface. Trace around the cups then loosen the winder knobs and mark the center hole. Screws are provided to fix the cups to the wall. Screw the cups to the wall and repeat Steps 5 and 6.

V. EXTENSION ASSEMBLY INSTRUCTIONS

VI. HOW TO RELEASE TUBE INSERTS

Pull out threaded presure pads as shown in diagram

as shown in diagram.

4.

No. 321...80mm No. 322...140mm No. 323...280mm No. 324...490mm No. 325...980mm No. 327...1490mm

VII. SAFETY NOTES AND INSTRUCTIONS

Figure 6

5.

WARNINGS: FOR THE INCREASED SAFETY OF YOUR CHILD

REPAIR YOUR DOOR BARRIER IF BROKEN OR DAMAGED BY AUTHORISED REPAIR AGENT. DO NOT USE UNTIL REPAIRED.CHECK THE DOOR BARRIER CONSTANTLY FOR LOOSE OR WORN PARTS AND REPAIR OR REPLACE PARTS AS NEEDED.ENSURE THAT THE DOOR BARRIER IS PROPERLY TIGHTENED AT ALL TIMES.NEVER ALLOW OLDER CHILDREN TO CLIMB THE DOOR BARRIER AS SERIOUS INJURY MAY OCCUR. ALWAYS FOLLOW THE INSTALLATION INSTRUCTIONS CAREFULLY AS THIS IS A SAFETY PRODUCT.ALWAYS INSTRUCT APPROPRIATE PERSONS WITH THE USE OF THIS PRODUCT. ALWAYS ENSURE THE DOOR BARRIER IS SECURELY FASTENED IN TIME OF USE.TO PREVENT SERIOUS INJURY OR DEATH, SECURELY INSTALL GATE OR ENCLOSURE AND USE ACCORDING TO MANUFACTURER’S INSTRUCTIONS.NEVER USE WITH A CHILD ABLE TO CLIMB OVER OR DISLODGE THE GATE OR ENCLOSURE.NEVER LEAVE CHILD UNATTENDED.INSTALL WITH LOCKING MECHANISM ON ONE SIDE AWAY FROM CHILD.CHECK THAT THE DOOR BARRIER IS SITTING FIRMLY AGAINST THE SURFACE (RIGHT DOWN AGAINST THE FLOOR).

Suitable for use for babies and toddlers up to the age of 24 months.Check the size of opening is within recommended dimensions.Ensure that the walls are solid and rigid and have an even grease free surface. Partitions and plaster board walls may not be strong enough to support the gate without using wall cups. If so screw the wall cups in position with screws supplied so overtightening is not necessary.Always use under adult supervision.For extra security, especially at the top of stairs, we recommend the use of the wall cups supplied.When used on staircases, the gate should only be placed on the top or bottom stairs depending on the area that the child is being retained in. Install adjacent to that area.

www . i n f a - s e c u r e . c om . a u

INFA SECURE PTY LTDP.O. Box 487, EMU PLAINS NSW 2750 110-114 Old Bathurst Rd, EMU PLAINS NSW 2750Service No: 02 4728 8090 Fax: 02 4728 8040

Infa Inquiries and Service (02) 4728 8090ISSUE: A