Protecting the Environment with Innovative Wastewater Treatment Solutions
2015 Product Catalog www.infiltratorwater.com
We Are an Environmentally Concerned CompanyInfiltrator products are an environmentally sustainable solution when compared to traditional construction materials due to the significant reduction in energy used to produce them and their high usage of recycled plastics.
ONE OF NORTH AMERICA’S TOP RECYCLERSEveryday, Champion Polymer, Infiltrator Water Technologies’ recycling division, purchases and processes plastic scrap for use in the production of Infiltrator products. As one of the top plastics recyclers in North America, we put millions of pounds of scrap polyolefin resins to use in our environmentally friendly products each year.
Recycled auto parts, carpeting, regrind and packaging materials.
Contact Infiltrator Water Technologies at 1-800-221-4436 for additional information. 3
About Infiltrator Water TechnologiesA proven leader with over 25 years of experience in the wastewater industry and an array of onsite water management products that allow for faster and more reli-able installations.
Quality, reliability and innovation are the cornerstones of our success. Infiltrator chamber systems, IM-Series tanks, cutting-edge Aquaworx products, and EZflow modular systems allow the Infiltrator customer one proven, reliable source for nearly all of their onsite wastewater needs.
A TESTED AND PROVEN SUCCESS RATE• Infiltrator is the leading manufacturer of onsite wastewater system products
in North America. • Over 2.5 million Infiltrator onsite wastewater leachfield systems have been
installed worldwide. • Nearly 50% of septic systems installed in the United States and Canada are
Infiltrator chamber or EZflow leachfields. • Beginning in 1987, Infiltrator products have stood the test-of-time
with an established history of performance and reliability.
PRODUCT AVAILABILITYWe have an extensive network of distributors throughout
North America. These knowledgeable professionals maintain local inventories of our products and also
provide contractors and installers with product delivery and installation support. Plus, Infiltrator has a dedicated, experienced team of sales, customer service, and technical assistance professionals who are focused on the septic industry.
RESPONSIVE SERVICE • Our technical staff and local sales representatives
maintain a strong presence where it counts–in the field.
• Installer, designer and engineer training and certification classes.
• Field demonstrations to help educate installers and regulators.
• Product brochures, installation manuals, and state- and province-specific design tools are available on our website or by calling our customer service team.
contents
Chamber Technology page 4
Quick4 Plus Chambers page 6
Quick4 Chambers page 8
EZflow Septic Systems page 12
EZflow Drainage Systems page 14
IM-Series Septic Tanks page 16
IM-Series Potable Water Tanks page 21
TW-Risers page 22
Aquaworx page 23
ONSITE WASTEWATER TREATMENT SYSTEMSInfiltrator Water Technologies offers a broad range of products that provide solutions for almost any onsite wastewater system, including:
Drainfields Septic Tanks Pump Tanks Holding Tanks Site Drainage Remediation Pump Control Panels
www.infiltratorwater.net
4 PRODUCT CATALOG www.infiltratorwater.com
Chamber TechnologySCIENCE PROVES THE ADVANTAGEInfiltrator chambers are typically installed in a smaller footprint with equal or better performance when compared to old-fashioned gravel and pipe drainfields. University research and large-scale field performance studies have verified a two and half times infiltrative efficiency advantage of the open infiltrative surface architecture provided by chamber systems over stone and pipe systems. The advantage lies in the absence of stones or stone fines that embed into, coat and clog the soil’s surface significantly reducing the infiltration of effluent.
An Infiltrator Chamber System is a direct replacement for old-fashioned stone and pipe leachfields. Infiltrator chambers give designers, installers and homeowners greater flexibility in the placement of the septic leachfield.
Compared With Stone and Pipe, Infiltrator Chambers Offer These Advantages• Cost Savings
Can be delivered to the site in a pickup truck and hand-carried into position.
For most jobs, two people can install a system in half-the-time it takes for a comparable stone and pipe leachfield.
No stone or geotextile is typically required, eliminating the need for heavy trucks used to transport stone.
• Less Site Disruption Chambers typically occupy a smaller total area than stone and pipe leachfields, so there is less site disturbance.
Elimination of stone means cleanup at the job site is much easier.
• Built To Last Chambers are chemical-resistant and UV-stable. Powerful arch-design supports axle loads of 16,000 lbs with 12” of compacted cover, equivalent to an AASHTO H-10 load rating.
All products carry a limited warranty and are certified by the International Association of Plumbing and Mechanical Officials (IAPMO).
Contact Infiltrator Water Technologies at 1-800-221-4436 for additional information. 5
Inspection port cutout
Louvered sidewall resists soil intrusion
Entire bottom of trenches open for unobstructed infiltration into soil
No stone or geotextile required
Large storage volume accommodates peak flows of effluent
Soil may intrude through unprotected surfaces
Geotextile required to prevent soil intrusion
4” perforated pipe does not provide even distribution
Soil compaction, stone embedment and fines reduce infiltration rate
Infiltrator Chamber System compared to a traditional stone and pipe system
Infiltrator Chamber FeaturesContour Swivel Connection™ allows the chamber to swivel up to 15°, right or left.
Higher long-term acceptance rate (LTAR) means you install a reliable top performing system.
Smaller footprint with equal or better performance allows less site disruption.
Fast, easy installation saves time and money.
Louvered sidewalls for maximum infiltration.
Low profile chambers for shallow placement applications.
Multiport endcaps allow for maximum flexbility.
Chamber system Stone and pipe system
Quick4 Plus Standard
Quick4 Standard
6 PRODUCT CATALOG www.infiltratorwater.com
Quick4 Plus Standard ChamberApplication: 36” wide trench, curved, straight or side by side in beds
Size: 34”W x 53”L x 12”H (864 mm x 1346 mm x 305 mm)
Effective Length: 48” (1219 mm)
Endcap: Quick4 Plus All-in-One 12
Quick4 Plus High Capacity ChamberApplication: 36” wide trench, curved, straight or side by side in beds
Size: 34”W x 53”L x 14”H (864 mm x 1346 mm x 356 mm)
Effective Length: 48” (1219 mm)
Endcap: Quick4 Plus All-in-One 12
Quick4 Plus All-in-One 12 EndcapApplication: Use at either end of a chamber row for an inlet/outlet or can be installed
mid-trench. Side, end or top inletting. Compatible with Quick4 Plus Standard and Quick4 Plus High Capacity Chambers.
Size: 34”W x 20.5”L x 13”H (864 mm x 520 mm x 330 mm)
Additional Length per Pair of Endcaps: 37” (940 mm) Additional Length
when used midline: 11.4” (290 mm)
Invert Height: 5.3”, 8” (134 mm, 203 mm) Optional Accessory: All-in-One Periscope
Quick4 Plus All-in-One PeriscopeApplication: Allows for raised, invert installations with 180° directional inletting.
All-in-One 8 Endcap: 9” raised invert. All-in-One 12 Endcap: 13” invert.
Size: 5”W x 9”L x 6”H (127 mm x 229 mm x 152 mm)
Invert Height: 9”, 13” (229 mm, 330 mm)
For Your InformationInterior Load-Bearing Support ColumnTop View
End View
Maximum Strength through center structural columns. • Quick4 Plus Standard • Quick4 Plus High Capacity
Contact Infiltrator Water Technologies at 1-800-221-4436 for additional information. 7
Quick4 Plus Standard Low Profile (LP) ChamberApplication Reduced height applications, 4” shorter than standard chambers.
36” wide trench, curved, straight or side by side in beds
Size 34”W x 53”L x 8”H (864 mm x 1346 mm x 203 mm)
Effective Length 48” (1219 mm)
Endcap Quick4 Plus All-in-One 8 or Quick4 Plus
Quick4 Plus Equalizer 36 Low Profile (LP) ChamberApplication Reduced height applications, 4” shorter than standard chambers.
24” wide trench, curved, straight or side by side in beds
Size 22”W x 53”L x 8”H (559 mm x 1346 mm x 203 mm)
Effective Length 48” (1219 mm)
Endcap Quick4 Plus All-in-One 8 or Quick4 Plus
Quick4 Plus All-in-One 8 EndcapApplication: Use at either end of a chamber row for an inlet/outlet or can be installed
mid-trench. Side, end or top inletting. Compatible with Quick4 Plus Low Profile Chambers.
Size: 18”W x 13”L x 8”H (457 mm x 330 mm x 203 mm)
Additional Length per Endcap:
10.4” (264 mm) Invert Height: 3.3” (84 mm) Optional Accessory: All-in-One Periscope
Quick4 Plus EndcapApplication: Simple, flat design that allows for a pipe installation at the end of the chamber row.
Piping drill points are set for gravity or pressure pipe. Compatible with Quick4 Plus Low Profile Chambers.
Size: 18”W x 7”L x 8”H (457 mm x 178 mm x 203 mm)
Additional Length per Endcap:
4.5” (114 mm) Invert Height: 3.3” (84 mm)
Maximum Strength through center structural columns. Low Profile for shallow applications.• Quick4 Plus Standard Low Profile• Quick4 Plus Equalizer 36 Low Profile
8"
34"
36" WIDE TRENCH
3.3"
Low Profile TrenchShallow Installation
8 PRODUCT CATALOG www.infiltratorwater.com
Quick4 Standard ChamberApplication: 36” wide trench, curved, straight or side by side in beds
Size: 34”W x 53”L x 12”H (864 mm x 1346 mm x 305 mm)
Effective Length: 48” (1219 mm)
Multiport Endcap with eight molded-in high and low inlets for maximum piping flexibility. Tear-out seals.
Size: 34”W x 16”L x 12”H (864 mm x 406 mm x 305 mm)
Additional Length per Pair of Endcaps:
26.4” (671 mm) Invert Height: 8” (203 mm)
• Quick4 Standard • Quick4 High Capacity
For Your InformationLouvered sidewalls provide maximum infiltration.
Quick4 High Capacity ChamberApplication: 36” wide trench, curved, straight or side by side in beds
Size: 34”W x 53”L x 16”H (864 mm x 1346 mm x 406 mm)
Effective Length: 48” (1219 mm)
Multiport Endcap with eight molded-in high and low inlets for maximum piping flexibility. Tear-out seals.
Size: 34”W x 19”L x 16”H (864 mm x 483 mm x 406 mm)
Additional Length per Pair of Endcaps:
28.8” (732 mm) Invert Height: 11.5” (292 mm)
*Length and number of trenches determined by design.
(36" WIDE TRENCH)34"
12" 8" INVERT
34"
COVER PER CODE
(36" WIDE TRENCH)SPACING PER CODE
NATIVE BACKFILLTOP SOIL
Typical Quick4 Standard Chamber Section View*
Contact Infiltrator Water Technologies at 1-800-221-4436 for additional information. 9
Specialty application chambers.• Quick4 Equalizer 36• Quick4 Equalizer 36 Straightlock• Quick4 Equalizer 24 and Equalizer 24 HD• Quick4 Equalizer 24 Low Profile
Quick4 Equalizer 36 Chamber Quick4 Equalizer 36 Straightlock ChamberApplication: 24” wide trench, curved, straight or
side by side in bedsApplication: Bed or straight trench
Size: 22”W x 53”L x 12”H (559 mm x 1346 mm x 305 mm)
Effective Length: 48” (1219 mm)
Multiport Endcap with six molded-in high and low inlets for maximum piping flexibility. Tear-out seals.
Size: 22”W x 16”L x 12”H (559 mm x 406 mm x 305 mm)
Additional Length per Pair of Endcaps:
25.2” (640 mm) Invert Height: 6” (152 mm)
Quick4 Equalizer 24 Chamber and Equalizer 24 Heavy Duty (HD) ChamberApplication: 18” or 24” wide trench, curved, straight or side by side in beds
Size: 16”W x 53”L x 11”H (406 mm x 1346 mm x 279 mm)
Effective Length: 48” (1219 mm)
Multiport Endcap with six molded-in high and low inlets for maximum piping flexibility. Tear-out seals.
Size: 16”W x 14”L x 12”H (406 mm x 356 mm x 305 mm)
Additional Length per Pair of Endcaps:
22.8” (579 mm) Invert Height: 6” (152 mm)
Quick4 Equalizer 24 Low Profile ChamberApplication: 18” or 24” wide trench, curved, straight or side by side in beds
Size: 16”W x 53”L x 8”H (406 mm x 1346 mm x 203 mm)
Effective Length: 48” (1219 mm)
Endcap offers a simple overlap design for easy installation.
Size: 14”W x 7”L x 8”H (356 mm x 178 mm x 203 mm)
Additional Length per Pair of Endcaps:
9” (229 mm) Invert Height: 2” (51 mm)
Shallow Trench Application18” Wide Trench
16"
8"
2"
10 PRODUCT CATALOG www.infiltratorwater.com
Septic Systems
GEOSYNTHETIC AGGREGATE TECHNOLOGYEZflow is an environmentally friendly replacement to old-fashioned stone and pipe in septic drainfields using an engineered geosynthetic aggregate modular design.
EZflow products are certified by IAPMO and the ICC-ES PMG Listing Program.
An EZflow system is designed to improve infiltrative performance by eliminating fines and reducing compaction and embedment associated with crushed stone. Pre-assembled units include a 4” perforated pipe surrounded by aggregate covered in geotextile and held in place with a durable high strength netting. Available in easy-to-contour 5’ and 10’ lengths in diameters of 7, 8, 9, 10, 12, 13, 14 or 18”.
Lightweight expanded polystyrene construction offers structural integrity and resists compaction. Engineered flow- channels increase void space creating improved water flow and greater storage.
Compared With Stone and Pipe, EZflow Bundles Offer These Advantages• Always clean and free of fines.• Bundles are quick to install, using simple
snap internal couplers, saving costs on heavy machinery and labor.
• Modular construction allows configurations to match trench dimensions for most system shapes and sizes.
• Engineered for optimal storage and absorption efficiencies.
• Ability to contour along sloped sites and around trees or landscaping.
• Lightweight, 5’ or 10’ lengths are perfect for repairs and tight job sites.
• Easier cleanup at job site with the elimination of stone.
• Manufactured from recycled materials rather than mined natural resources.
• Approved in most jurisdictions with an increased efficiency rating, reducing drainfield size.
• Backed by the leader in the onsite wastewater industry.
Contact Infiltrator Water Technologies at 1-800-221-4436 for additional information. 11
EZflow Bundle System compared to a traditional stone and pipe system
Soil may intrude through unprotected surfaces
Geotextile required to prevent soil intrusion
Soil compaction, stone embedment and fines reduce infiltration rate
Extended geotextile barrier eliminates intrusion through unprotected surfaces
Geosynthetic aggregate is free of fines
Plastic netting
Engineered geosynthetic aggregate eliminates compaction and fines
Perforated pipe
* One bundle contains a 3” or 4” (depending on bundle diameter) centered corrugated, polyethylene pipe surrounded by aggregate and covered with geotextile.
†Low pressure pipe is installed within the corrugated pipe.
EZflow Bundles for Septic Applications
Diameter
Polyethylene Pipe*
Single Bundle System
Horizontal Bundle System
Vertical Bundle System
Triangular Bundle System
Part # # of bundlesLPP
Option† Part # # of bundles Part # # of bundles Part # # of bundles
7” • 0701P-GE0 1 0705H-GEO 5
8” • 0801P-GE0 1
9” • 0904H-GEO 4
10”
• 1001P-GE0 1 • 1001LPP-GE0
1002H-GEO 1003H-GEO
2 3
1002V-GEO 1003V-GEO 1004V-GEO 1006V-GEO
2 3 4 6
1003T-GEO 3
12”
• 1201P-GEO 1 • 1201LPP-GE0
1202H-GEO 1203H-GEO 1206H-GEO
2 3 6
1202V-GEO 1203V-GEO 1204V-GEO 1206V-GEO
2 3 4 6
1203T-GEO 3
13” • 1 1303H-GEO 3 1303T-GEO 3
14” • 1401P-GEO 1 1402H-GEO 2 1402V-GEO 2 1403T-GEO 3
18” • 1801P-GEO 1 1802H-GEO 2NOTES: 1. Other systems include square and bed systems that use a variety of bundle diameters.
Trench width/depth and bed width will dictate the number of bundles.2. System dimensions are dependent upon bundle diameter and configuration.3. Distribution pipe and internal couplings meet the requirements of ASTM F405.4. Bundles are also available without geotextile between the netting and synthetic aggregate.
LIGHTWEIGHTEasily transported.
EZflow system Stone and pipe system
12 PRODUCT CATALOG www.infiltratorwater.com
Drainage Systems
GEOSYNTHETIC AGGREGATE TECHNOLOGYEZflow Drainage Systems are geosynthetic aggregate pipe systems for use in drainage applications. The gravel-less drainage system utilizes the time proven principle of gravel systems while eliminating the problems inherent with gravel.
EZflow products are certified by IAPMO and the ICC-ES PMG Listing Program.
Products provide maximum system life and performance, lower system costs and an environmentally friendly alternative.
Each EZflow drainage product is 10’ in length with a slotted pipe surrounded by polystyrene aggregate and enclosed in geotextile mesh. Configurations are available in 7” diameter bundles with or without a 3” pipe, 10” diameter bundles with or without a 4” pipe, and 15” diameter bundles with or without a 6” pipe. Accessories include 3” and 4” internal couplers, endcaps, internal tees and internal wyes.
EZflow Drainage Bundles Offer These Advantages• Convenient 10’ long sections are easy to
connect using internal couplers. • EZflow products are easily transported and
installed by a single worker dramatically reducing labor costs.
• Superior flow rate when compared to gravel due to lack of fines.
• EZflow drainage systems have high storage capacity created by the engineered flow channels in the aggregate.
• EZflow’s aggregate pipe combination and aggregate-only bundles can easily bend around corners and other obstacles to conform to your project’s needs.
• Using EZflow recycled polystyrene aggregate prevents millions of pounds of waste from entering landfills.
• EZflow drainage products are reliable, which means fewer call backs.
EZflow Bundles for Drainage Applications7” Bundles 10” Bundles 15” Bundles
Part # Description Part # Description Part # Description
701A-MESH
7” Diameter
1001A-MESH
10” Diameter
1501A-MESH
15” Diameter
701F-MESH
7” Diameter with 3” Pipe in Center
1001F-MESH
10” Diameter with 4” Pipe in Center
1501FC-MESH
15” Diameter with 6” Pipe in Center
1001FB-MESH
10” Diameter with 4” Pipe at Bottom
1501FB-MESH
15” Diameter with 6” Pipe at Bottom
10"
10"
10"
15"
15"
15"
7"
7"
Contact Infiltrator Water Technologies at 1-800-221-4436 for additional information. 13
EZflow Bundles for Drainage
Geotextile barrier
Geosynthetic aggregate is free of fines
Geotextile mesh
Slotted corrugated
pipe
DRAINAGE SYSTEMSFOUNDATION DRAINSInstall at the base of a foundation to divert water away from a house. Without foundation drainage, water can collect and permeate through a foundation, leading to basement flooding. EZflow units can be used individually or stacked as a foundation drain replacing stone and pipe.
FRENCH DRAINSEliminate excess water from low points and other areas prone to saturation on a property. Large french drains are often installed in a herringbone pattern, diverting water to a down-gradient outlet.
LANDSCAPE DRAINSIdeal for the prevention of excessive water in and around landscaped areas or gardens. Lightweight bundles can be installed quickly with limited site disruption compared to traditional stone systems which can be messy and destroy vegetation.
ROOF RUN-OFF DRAINSRainwater run-off can be collected from the roof by way of guttering and conveyed away from the house using an EZflow drainfield.
INTERCEPTOR OR CURTAIN DRAINSIntercept groundwater and redirect flow. EZflow is the perfect solution since interceptor drains are typically installed on sloping land, plus moving stone and materials close to a job site can be difficult.
RETAINING WALL DRAINSUse to relieve pressure that water can exert on a retaining wall. Reduce concerns associated with backfilling a wall with stone during construction, EZflow drainage systems can be placed at the base or stacked on the backside of a wall to direct the water away from the wall.
Lightweight expanded polystyrene construction offers structural integrity and resists compaction. Engineered flow-channels increase void space creating improved water flow and greater storage.
14 PRODUCT CATALOG www.infiltratorwater.com
IM-Series Septic Tanks: Redefining StrengthA REVOLUTIONARY ADVANCEMENT IN SEPTIC TANK DESIGNInjection molded IM-Series septic tanks offer exceptional long-term strength and are compatible with Infiltrator’s line of custom fit risers and heavy duty lids. Made from recycled materials, IM-Series septic tanks are environmentally-friendly products.The engineered mid-seam joint accepts a continuous loop EPDM gasket. Infiltrator’s EPDM gasket design utilizes technology and materials from the sanitary sewer pipe industry to deliver a reliable watertight seal. The two-piece tank body is permanently aligned and fastened using an integrated system of high-strength plastic alignment dowels and locking seam clips. The tank can be installed with 6” to 48” of soil cover, does not require water filling during installation and can be pumped dry during pump-outs. All IM-Series septic tanks are fully assembled and available through our network of certified Infiltrator distributors.
The IM-Series watertight septic tank design is offered with Infiltrator’s line of custom-fit risers and heavy-duty lids. Infiltrator injection molded tanks provide a revolutionary improvement in plastic tank design, offering long-term exceptional strength and watertightness.
Contact Infiltrator Water Technologies at 1-800-221-4436 for additional information. 15
IM-Series Septic Tanks Offer These Advantages
• Strong injection molded polypropylene construction.
• Lightweight plastic construction and inboard lifting lugs allow for easy delivery and handling.
• Integral heavy-duty green lids interconnect with TW™ risers and pipe riser solutions.
• Structurally reinforced access ports eliminate distortion during installation and pump-outs.
• Reinforced structural ribbing and fiberglass bulkheads offer additional strength.
• Can be installed with 6” to 48” of cover.
• Can be pumped dry during pump-outs (no need to refill with water).
• Suitable for use as a septic tank, pump tank, or rainwater (non-potable) tank.
• No special installation, backfill or water filling procedures are required.
Mid-seam Cutaway Reinforced watertight mid-seam gasketed connection
Partition baffle wall
Heavy Duty Lid CutawayReinforced 24” structural access port
Structural bulkheads
IM-1060 TANK CUTAWAY
Strong Injection Molded Polypropylene Construction
Infiltrator IM-Series Tanks
Tank
IM-540
IM-1060
IM-1530
Applications Suitable for use as a pump tank, trash-tank, rainwater
(non-potable) tank, or as the second compartment of an
in-series septic tank.
Suitable for use as a pump tank, septic tank or rainwater tank, shallow, multiple, and serial tank configurations.
Suitable for use as a pump tank, septic tank or rainwater tank, shallow, multiple, and serial tank configurations.
Working Capacity 475 gal (1798 L) 1094 gal (4141 L) 1537 gal (5818 L)
Total Capacity 552 gal (2090 L) 1287 gal (4872 L) 1787 gal (6764 L)
16 PRODUCT CATALOG www.infiltratorwater.com
• IM-540
For Your InformationLong-term exceptional strength and watertightnessSuitable for use as a septic/pump tank, trash-tank, rainwater (non-potable) tank, or as the second compartment of an in-series septic tank.
24” diameter access opening with locking lid.
OPTIMAL FOR USE IN-SERIES WITH OTHER TANKS
APPLICATIONSRETROFIT: The IM-540 can increase the volume of an existing septic tank.NEW: Use the IM-540 in new in-series installations with another tank. TRASH/PUMP-TANK: Ideally-sized for use as a trash-tank or pump tank.
IM-540
Infiltrator IM-540 TankApplication: Septic/pump tank, trash-tank,
rainwater (non-potable) tank, or as the second compartment of an in-series septic tank
Working Capacity: 475 gal (1798 L)
Total Capacity: 552 gal (2090 L)
Size: 61.7”W x 54.6”H x 64.9”L (1567 mm x 1387 mm x 1648 mm)
Liquid Level: 44.0” (1118 mm)
Invert Drop: 3” (76 mm)
Maximum Pipe Diameter: 4” (102 mm)
Infiltrator IM-1060 TankApplication: Septic tank, pump tank
or rainwater (non-potable) tank
Working Capacity: 1094 gal (4141 L)
Total Capacity: 1287 gal (4872 L)
Size: 62.2”W x 54.7”H x 127”L (1580 mm x 1389 mm x 3226 mm)
Length-to-Width Ratio: 2.3 to 1
Liquid Level: 44.0” (1118 mm)
Invert Drop: 3” (76 mm)
Fiberglass Supports: 2
Compartments: 1 or 2
Maximum Pipe Diameter: 6” (152 mm)
• IM-1060
For Your InformationIM-Series tanks: The quickest installation in the onsite industryCan be installed with 6” to 48” of cover.
IM-1060
Contact Infiltrator Water Technologies at 1-800-221-4436 for additional information. 17
Infiltrator’s chambers, IM-Series septic tanks and EZflow leachfield products are manufactured from 95% recycled plastics.
For A Greener Tomorrow
Infiltrator IM-1530 TankApplication: Septic tank, pump tank
or rainwater (non-potable) tank
Working Capacity: 1537 gal (5818 L)
Total Capacity: 1787 gal (6764 L)
Size: 61.7”W x 54.5”H x 175.6”L (1567 mm x 1384 mm x 4460 mm)
Length-to-Width Ratio: 2.8 to 1
Liquid Level: 44” (1118 mm)
Invert Drop: 3” (76 mm)
Fiberglass Supports: 4
Compartments: 1 or 2
Maximum Pipe Diameter: 4” (102 mm)
For Your Information
The two-piece design is permanently fastened using a series of non-corrosive plastic alignment dowels and locking seam clips.
The IM-1530 is an injection molded two piece mid-seam plastic tank. The IM-1530 injection molded plastic designallows for a mid-seam jointthat has precise dimensionsfor accepting an engineeredEPDM gasket. Infiltrator’sgasket design utilizestechnology from the waterindustry to deliver proven means of maintaining a watertight seal.
PERCODE
PERCODE
44.0[1,118]LIQUIDDEPTH
3.0[76]
10.1 [257] FREEBOARD
175.6 [4,460] EXTERIOR LENGTH
61.7[1,567]
EXTERIORWIDTH
54.5[1,384]
EXTERIORHEIGHT
ISOMETRICVIEW
SIDE INLET/OUTLET (TYP.)
Ø 4 [102]PVC OR ABSINLET TEE
Ø 24.0 [610] ACCESS PORTWITH LOCKING LID (3)
INLETOUTLET
Ø 4 [102]PVC OR ABSOUTLET TEE
TANKINTERIOR
INLETTEE
LIDCONTINUOUSELASTOMERIC
GASKET
1.5 [38]
ALIGNMENTDOWEL
TANKINTERIOR
CONTINUOUS
ELASTOMERIC
GASKET
SEAM CLIP
TANK BOTTOM HALF
TANK TOP HALF
SECTION B - B'END VIEW
FIBERGLASSSUPPORT
2 [51] X 2 [51]FIBERGLASSSUPPORT (4)(TYP.)
16.9% AIR SPACE
SEAM CLIP(TYP.)
LIFTING STRAP(TYP.)
RISER CONNECTION (TYP.)LIFTING STRAP (TYP.)
LIFTING LUG (TYP.)
ACCESS PORT RIM
0.2 [5] WALLTHICKNESS
OUTLET TEE(TYP.)
18 PRODUCT CATALOG www.infiltratorwater.com
• IM-1530
IM Series – Potable Water TanksRELIABLE PERFORMANCE The Infiltrator IM-Series Potable Water tanks are lightweight, strong and durable. These potable, watertight tank designs are offered with Infiltrator’s potable heavy-duty lids. Infiltrator injection-molded tanks provide a revolutionary improvement in plastic tank design, offering long-term exceptional strength and watertightness.
• IM-550C • IM-1280C • IM-1760C
Contact Infiltrator Water Technologies at 1-800-221-4436 for additional information. 19
Infiltrator IM-Potable Water Tank SeriesParameter IM-550C IM-1280C IM-1760C
Total Capacity (gal) 552 1287 1787
Length (in) 65 127 176
Width (in) 62 62 62
Height (in) 55 55 55
Fiberglass Supports - 0 2 4
Max Burial Depth (in) 48 48 48
Minimum Burial Depth (in) 6 6 6
Maximum Pipe Diameter (in) 4 6 4
Weight (lb) 191 346 501
For Your InformationInfiltrator’s IM-Series Potable water tanks are available in 552-gallon, 1287-gallon and 1787-gallon capacities and are certified to NSF/ANSI 61 for potable uses.
• Strong injection-molded polypropylene construction• Lightweight plastic construction and inboard lifting lugs allow for
easy delivery and handling • Structurally reinforced access ports eliminate distortion
during installation and pump-outs • Reinforced structural ribbing
and fiberglass bulkheads offer additional strength • Can be installed with 6” to 48” of cover • Can be pumped dry • No special installation, backfill or water filling procedures are required
Suitable for use as a potable pump tank, rainwater harvesting
tank or water storage tank
IM-Series Potable Water Tanks Offer These Advantages
• Riser sections, lids and flanges
For Your InformationLightweight polypropylene makes TW-Risers very easy to install.TW-Risers are resistant to chemical and soil corrosion. They are also thoroughly sealed and will prevent gases from escaping the system.
TW-Risers include a set of indexing structural ribs which lock riser pieces in place to further ensure a watertight seal.
Concrete risers are very heavy and therefore more time consuming to install.
Strength and DurabilityTW-Risers by Infiltrator are made from glass-reinforced polypropylene, providing superior strength and durability. Available in green or black with a 24” diameter, TW-Risers are ideal for use with any concrete or plastic tank. Lids are fastened using stainless steel screws and are further secured by indexing structural ribs, which lock the riser into place.
Lid Systems Offer These Advantages• Made from virgin polypropylene, providing
strength and increased impact resistance. • Improved urethane gasket creates
a built-in watertight seal.
• Slip-resistant lids come with an indexing mechanism locking them into place and can withstand a wheel load comparable to that of a full size pick-up truck.
20 PRODUCT CATALOG www.infiltratorwater.com
TW-Series tank lid
6” height riser section
12” height riser section
18” height riser section
24” adapter flange
TW-Risers 24” Riser SystemIncluded Components:
24” x 6” Risers24” x 12” Risers24” x 18” Risers24” Lids
Available Accessories:
Adhesive SealantSafety Lid System24” Adapter FlangeBulkhead FittingsPipe Adapter Ring
Creates a watertight connection when using HDPE, IPEX or Ultra Rib pipe with a IM-Series Tank.
TW-Risers View our website video
series and learn how to quickly and easily
install a watertight riser.
EZset™ Riser Systems also available in 20”, 24”, and 30” diameter products. Contact Infiltrator for more information.
• Remediator
For Your InformationA proven track record.More than 4,000 failing septic systems have been restored to normal operation with this bioremediation technology.
The Aquaworx Remediator is a technology that is accepted or approved as a septic system repair by numerous regulatory agencies.
Contact Infiltrator Water Technologies at 1-800-221-4436 for additional information. 21
Rejuvenate a Failing LeachfieldThe Aquaworx Remediator is a simple, easy-to-install septic system remediation technology that rejuvenates a failing leachfield with minimal landscape disruption. The unique system is inserted into an existing septic tank of a malfunctioning system and reverses the drainfield clogging process.
Aquaworx Remediator Offers These Advantages Aquaworx RemediatorColumn Diameter at Top: 12” (305 mm)
Column Diameter at Base: 15” (381 mm)
Total Height: 30” (762 mm)
Weight: 38 lbs (17 kg)
Flow Rate: 600 gal/day for a 4 bedroom house
Air Pump Weight: 13 lbs (6 kg)
Air Pump Dimensions:
6.8”W x 8.2”L x 7.5”H (173 mm x 208 mm x 191 mm)
Easy installation. Natural process. Minimal landscape disruption.
• Eliminate the need for a complete drainfield
replacement and the resulting landscape damage caused by heavy equipment.
• Problems associated with a failing septic system such as odors and wet areas in the yard are eliminated in as little as 2 weeks.
• Environmental solution that strengthens the natural process of wastewater treatment and groundwater recharge.
• Easy installation with no heavy equipment allows for minimal disruption and quick return on investment.
• Permanent, noninvasive solution that requires minimal cost to operate and maintain.
22 PRODUCT CATALOG www.infiltratorwater.com
Cost-Effective SolutionPowered by an embedded microprocessor in the pump controller and a floatless pressure transducer in the pump chamber, the IPC Panel monitors liquid levels, controls pumping time intervals and logs events in real-time. Using the MARC™ as the user interface, the IPC Panel offers a cost-effective solution with expanded capabilities.
• Intelligent Pump Control Panel (IPC)
Aquaworx Control Panels Offer These Advantages• Simplified wiring for easy installation.• Unique user interface with Mountable
and Removable Controller (MARC™).• Data logging provides easy access to historical data.• Accurate timings eliminates need for a stopwatch.• Liquid level displayed for draw-downs means
no tape measure required. • Veto level override function allows
different timing at different loads. Simplex IPC Panel shown.
For Your InformationA Single Transducer.The Transducer continuously updates the liquid level to the panel.
• The Original Floatless Pump Control Technology US Patent No. 6,632,072
Aquaworx Control PanelsModel Features
Simplex IPC Panel Time controls a single pump. Panel comes with a removable MARC™
120 VAC, 20 FLA, 1HP Max. or 220 VAC, 20 FLA, 2HP Max.
UL/cUL ListedVisual alarm
NEMA 4X enclosure Automatic reset panel and alarm
Manual/Off/Auto operation Audible alarm with push to silence
Built-in dose counter and pump run time meter
Floatless pressure transducer in the pump chamberVisual heartbeat indicator
Programmable on and off timerReal time clock with battery back-up
Programmable start, stop and alarm levelExclusive VETO feature
Date / time stamped event log
Duplex IPC Panel Controls two pumps in an alternating design with independent timing. Panel comes with a removable MARC™
Sandfilter IPC Panel Time controls two individual pumps having independent level sensors. Allows for a design which will simultaneously time dose a treatment system and drainfield. Panel comes with a removable MARC™
Available Options
Circuit breakers Remote alarm panel Intrinsically safe barrier (Class I, Division I)Lockable latch Panel heater
The MARC™
Data logging capabilities of the IPC Panel enable monitoring of multiple types of system events, enhancing operational assessment, troubleshooting and maintenance of the system. The IPC Panel utilizes the MARC™ to collect system data and transfer it to PC-based applications using an SD card. Since it can be moved from job site to job site, the MARC™ enables the contractor or designer to have full control over the system and limits the ability of the homeowner to adjust system settings themselves.
The Transducer
Currently systems with floats, timers and motor contactors are used to control most timed septic pump systems. The Aquaworx Transducer Assembly connects to the panel with a 3-wire cable, making it easier to wire and more cost effective than a float system. With most mechanical systems, floats trigger the timer and alarms at specific liquid levels. For each level, a function and float are required, and typically 3 to 5 floats are installed. Aquaworx utilizes a Transducer Assembly that continuously updates the liquid level to the panel. A single transducer is all that is required for multiple functions, and it provides all of the data the controller needs to perform system functions. The durable construction of the transducer protects it from corrosion and harsh environments, allowing for a long and reliable life.
The MARC™ collects system data.
24 PRODUCT CATALOG www.infiltratorwater.com
ISO 9001 Registered.U.S. Patents: 4,759,661; 5,017,041; 5,156,488; 5,336,017; 5,401,116; 5,401,459; 5,511,903; 5,716,163; 5,588,778; 5,839,844 Canadian Patents: 1,329,959; 2,004,564. Other patents pending.Infiltrator, Equalizer, Quick4 and SideWinder are registered trademarks of Infiltrator Water Technologies, LLC. Infiltrator is a registered trademark in France. Infiltrator Water Technologies is a registered trademark in Mexico.Contour, MicroLeaching, PolyTuff, MultiPort, SnapLock, StraightLock, ChamberSpacer, PosiLock, QuickCut and QuickPlay are trademarks of Infiltrator Water Technologies © 2015 Infiltrator Water Technologies, LLC Printed in U.S.A. L01 0514 Not responsible for any typographic errors.
Distributed By:
PO Box 768 • Old Saybrook, CT 06475Phone 1-800-221-4436Fax 860-577-7001www.infiltratorwater.com
®
www.facebook.com/infiltratorwaterwww.youtube.com/infiltratorwaterwww.linkedin.com/company/infiltratorwater