PUBLIC/NON-CONFIDENTIAL COPPER PIPE FITTINGS RR-2015-003 FOREIGN PRODUCERS' QUESTIONNAIRE INTRODUCTION The information requested in this questionnaire is for use by the Canadian International Trade Tribunal (the Tribunal) in connection with its expiry review respecting the dumping of solder joint pressure pipe fittings and solder joint drainage, waste and vent pipe fittings, made of cast copper alloy, wrought copper alloy or wrought copper, for use in heating, plumbing, air conditioning and refrigeration applications, restricted to the products enumerated in the "Products Covered" tab, originating in or exported from the United States of America (United States), the Republic of Korea (Korea) and the People’s Republic of China (China) and the subsidizing of copper pipe fittings originating in or exported from China. The information is requested pursuant to subsection 17(2) of the Canadian International Trade Tribunal Act and is for use by the Tribunal in connection with the expiry review it initiated under section 76.03(3) of the Special Import Measures Act . The requested information is needed to supplement data available from other sources. As a foreign producer of copper pipe fittings, you are required to complete this questionnaire. You may return your completed questionnaire using one of the following methods, no later than August 11, 2016: 1. digital media (e.g. CD or DVD or USB key) sent to the Registrar, Canadian International Trade Tribunal, 333 Laurier Ave W, 15th Floor, Ottawa, Ontario K1A 0G7; 2. in hard copy sent to the Registrar, Canadian International Trade Tribunal, 333 Laurier Ave W, 15th Floor, Ottawa Ontario K1A 0G7; 3. by secure e-filing service (please visit: https://apps.citt-tcce.gc.ca/sftapp/CITT/html/transfer_e.html); or 4. by electronic mail to [email protected] if you accept the associated risks and are filing information that belongs to your firm only. It is preferable to file an electronic version of your response to the questionnaire. Your completed questionnaire should be filed EITHER electronically OR in hard copy, but NOT BOTH. In conducting this expiry review, the Tribunal is required to gather the best possible evidence. It is in your interest to ensure that your response to this questionnaire is accurate, complete and to return it to the Tribunal by the due date. Information that is confidential in nature will be treated in accordance with sections 43 to 49 of the Canadian International Trade Tribunal Act , which require that such information shall not be made public in such a manner as to be available for the use of any business competitor or rival of the reporting person, firm or corporation. If your firm did NOT produce copper pipe fittings, as described in the yellow "Case Information" tab and listed in the yellow "Products Covered" tab, during the period of review (January 1, 2013, to March 31, 2016), please provide the information requested in the blue "Certification" tab. You do NOT need to respond to the rest of the questionnaire.
The information requested in this questionnaire is for use by the Canadian International Trade Tribunal (the Tribunal) in connection with itsexpiry review respecting the dumping of solder joint pressure pipe fittings and solder joint drainage, waste and vent pipe fittings, made ofcast copper alloy, wrought copper alloy or wrought copper, for use in heating, plumbing, air conditioning and refrigeration applications,restricted to the products enumerated in the "Products Covered" tab, originating in or exported from the United States of America (UnitedStates), the Republic of Korea (Korea) and the People’s Republic of China (China) and the subsidizing of copper pipe fittings originating in orexported from China.
The information is requested pursuant to subsection 17(2) of the Canadian International Trade Tribunal Act and is for use by the Tribunal inconnection with the expiry review it initiated under section 76.03(3) of the Special Import Measures Act . The requested information isneeded to supplement data available from other sources.
As a foreign producer of copper pipe fittings, you are required to complete this questionnaire. You may return your completed questionnaireusing one of the following methods, no later than August 11, 2016:
1. digital media (e.g. CD or DVD or USB key) sent to the Registrar, Canadian International Trade Tribunal, 333 Laurier Ave W, 15th Floor, Ottawa, Ontario K1A 0G7;
2. in hard copy sent to the Registrar, Canadian International Trade Tribunal, 333 Laurier Ave W, 15th Floor, Ottawa Ontario K1A 0G7;
3. by secure e-filing service (please visit: https://apps.citt-tcce.gc.ca/sftapp/CITT/html/transfer_e.html); or
4. by electronic mail to [email protected] if you accept the associated risks and are filing information that belongs to your firm only.
It is preferable to file an electronic version of your response to the questionnaire. Your completed questionnaire should be filed EITHER electronically OR in hard copy, but NOT BOTH.
In conducting this expiry review, the Tribunal is required to gather the best possible evidence. It is in your interest to ensure that yourresponse to this questionnaire is accurate, complete and to return it to the Tribunal by the due date.
Information that is confidential in nature will be treated in accordance with sections 43 to 49 of the Canadian International Trade TribunalAct , which require that such information shall not be made public in such a manner as to be available for the use of any business competitoror rival of the reporting person, firm or corporation.
If your firm did NOT produce copper pipe fittings, as described in the yellow "Case Information" tab and listed in the yellow "Products Covered" tab, during the period of review (January 1, 2013, to March 31, 2016), please provide the information requested in the blue "Certification" tab. You do NOT need to respond to the rest of the questionnaire.
Introduction Instructions on how to return questionnaire responses.
Index References to, and explanation of, different tabs in questionnaire.
General Instructions
Instructions regarding the composition of the questionnaire and completion guidance.
Case Information Information specific to this expiry review including product information, tariff classification, period of review, due date of completed questionnaire and contact information for trade remedies investigations officers assigned to this case.
Products Covered List of copper pipe fittings covered by the Tribunal’s orders made on February 17, 2012, in Expiry Review No. RR-2011-001, by product category and description.
Glossary Definition of terms used in this questionnaire.
Part I - Public/Non-confidential Information (Blue Tabs)
Certification Sign off sheet indicating your firm's activities during the period of review. This sheet, once completed, forms part of your firm's questionnaire response.
Public Information Public/non-confidential information to be provided by your firm.
Public Info. Comments
Should your firm wish to add any comments related to Public Information, you may do so in this tab.
Part II - Confidential Information (Green Tabs)
Confidential Information
Confidential Information to be provided by your firm.
CapProdImpSales Schedule 1 - Practical Plant Capacity, Inventories, Production, Imports and Sales of Copper Pipe Fittings Produced by Your Firm in Your Home Country
PART I - deals with information that is public or non-confidential in nature. Requests to treat any of this information as confidential must be fully justified in writing and be accompanied by a redacted public or non-confidential version. PART I deals with general firm, industry data and product-specific information.
PART II - deals with information that is confidential in nature.
2. If your firm has more than one location, facility or outlet, please ensure that you submit to the Tribunal a consolidated reply to thequestionnaire.
3. If the answer to any question is “none,” “not applicable” or “not available,” please indicate which of these situations applies ratherthan leave the space blank.
4. All information is requested on a calendar-year basis. Where adjustments are required to comply with the Tribunal’s request,please identify the adjustments and give a full explanation of how they were made.
5. Unless otherwise specified, all responses to volume questions should be expressed in "pieces" and all responses to valuequestions should be expressed in Canadian dollars (CAD$).
6. If the information requested is not readily available from your records in exactly the form requested, please furnish preparedestimates, with a full explanation of the methodology used to prepare these estimates.
7. Comments or explanations with respect to any question should be made in the space provided or in a separate file submitted withyour response to the questionnaire.
8. Financial working papers should be stored in separate electronic files if an electronic version of the completed questionnaire issent to the Tribunal. Further explanations to supplement your answers should be stored and sent to the Tribunal as indicated inthe yellow "Introduction" tab. If you are forwarding to the Tribunal a paper copy of the completed questionnaire, please also senda paper copy of the above-mentioned support documents. You must ensure that these documents are provided in a photocopy-ready format, unbound, in either English or French. Please note that ONLY the relevant pages that cover the goods in questionshould be submitted.
9. In order to assist respondents with the completion of the questionnaire, certain questions include pull down menus. These menus are activated by clicking in the cell and then clicking on the arrow in the bottom right-hand corner.
10. In order to preserve formatting, when copying information into an existing cell, double click into the destination cell then paste the text. PLEASE DO NOT EXCEED 1,000 CHARACTERS PER CELL. Should you need more space, please use the "Comments" sections.
The goods subject to this expiry review are defined as:
Solder joint pressure pipe fittings and solder joint drainage, waste and vent pipe fittings, made of cast copper alloy, wrought copperalloy or wrought copper, for use in heating, plumbing, air conditioning and refrigeration applications, restricted to the productsenumerated in the "Products Covered" tab, originating in or exported from the United States, Korea and China.
The following copper pipe fittings were excluded by the Tribunal in Inquiry No. NQ-2006-002, February 19, 2007, and are therefore not subject to this expiry review: "4 cast drainage lead 8 oz. closet flange" and "4 cast drainage 14 oz. lead closet flange".
ADDITIONAL PRODUCT INFORMATION
Copper pipe fittings are used to connect copper pipes, tubes or other fittings to one another. The methods of joining copper fittingsinclude soldering, silver brazing and epoxy or similar gluing techniques. The connections are made by fitting two pieces together andheating the ends of the tubing and fitting, and filling the gap between the two with melted solder which solidifies on cooling to form astrong, leak proof connection. The fittings can also be used to connect copper tubing to other metal systems by use of threadedfittings. However, at least one end of a fitting is always soldered. Finally, the connection can also be made using epoxy or similargluing methods.
Copper pipe pressure fittings may be used in conveying liquids (e.g. potable water), gases and air under pressure in residential,industrial, commercial and institutional buildings. Copper pipe pressure fittings are also used in a variety of air-conditioning andrefrigeration (ACR) applications. The types of fittings used in air conditioning applications are typically identified by reference to theiroutside diameters, whereas the same fittings used in non-air conditioning applications such as plumbing and heating are typicallyidentified by reference to their inside or “nominal” diameters. Apart from the reference to diameter, a fitting for an air conditioningapplication is the same as a fitting for a non-air conditioning application.
Copper pipe drainage, waste and vent (DWV) fittings are used primarily to convey waste from buildings to sewers and for ventingpurposes under low-pressure conditions.
Female and male adaptors are used to connect a copper tube to an iron pipe or a water heater. Other adapters include ferrules thatare used to join a copper tube to a cast-iron pipe in older installations. Bushings are used to reduce the diameter of other fittings.Couplings are used to join tubes of either the same size or two different sizes to make longer runs through buildings. Elbows are usedto change the direction of a copper tube. Flanges and unions are used to provide a connection that can be either unscrewed orunbolted for maintenance or repairs. Tees are used to allow a copper line to be split into two separate lines. There are pressure teesand drainage tees; TY’s (90°) and Y’s (45°). Traps are used to trap water to prevent sewer gases from coming back into a building.Cleanouts are used to provide access to drainage systems in case of blockage; and caps are removable plugs used to permit inspectionand access for the purpose of clearing an obstruction.
Please be aware that the above tariff classification numbers may include a broad range of goods that are both subject to and not subject to this expiry review. As well, please be aware that subject goods may have been imported into Canada using tariff classification numbers other than those listed above.
PERIOD OF REVIEW
January 1, 2013, to March 31, 2016
DUE DATE
As a domestic producer of copper pipe fittings, you are required to complete this questionnaire and return the completed questionnaire no later than August 11, 2016.
INVESTIGATIONS OFFICERS ASSIGNED TO THIS CASE
Any questions relating to this questionnaire should be directed to:
WP: Wrought Pressure FTG: Fitting End (Street End)WD: Wrought Drainage LT: Long TurnCP: Cast Pressure MJ: Mechanical JointCD: Cast Drainage DE: Drop EarC: Copper Tube Cupped End or Sweat End DWV: Drainage Waste, VentM: Male NPT Thread TY: 90˚ Drainage TeeFE: Female NPT Thread Y: 45˚Drainage TeeSJ: Slip Joint End
The tables to this appendix list, by product category, the copper pipe fittings that are covered by the Tribunal’s orders. Where an asterisk (*) follows a specific copper pipe fitting description, it indicates that both wrought and cast copper pipe fittings are covered by the Tribunal’s orders.
Products Covered by the Tribunal’s Orders Made on February 17, 2012, in Expiry Review No. RR‑2011-001
Copper pipe fittings are identified in terms of imperial measurement, i.e. inches. However, the metric equivalents of the imperial measurement are also covered by the Tribunal’s orders. The term “metric equivalent” refers to those copper pipe fittings that are soft converted equivalents of the imperial-sized copper pipe fittings and does not include fittings that are made specifically in metric dimensions. Copper pipe fittings are also identified in terms of nominal size.
Copper pipe fittings are identified in the tables to this appendix using the following abbreviated terms:
1-1/2 X 1 CXFE CP ADAPTER* 1-1/2 X 2 CXFE CP ADAPTER*2 CXFE CP ADAPTER* 2-1/2 C X FE CP ADAPTER*3 CXFE CP ADAPTER* 1/2 CXFE CP DROP EAR ADAPTER 3/4 CXFE CP DROP EAR ADAPTER 1/2 CXFE CP HIGH EAR ADAPTER*4 CXFE CP ADAPTER* 5 C X FE CP ADAPTER*6 C X FE CP ADAPTER* 1-1/4 CXFE WD ADAPTER*1-1/4 X 1-1/2 CXFE WD ADAPTER* 1-1/4 FTGXFE WD ADAPTER*1-1/2 FTGXFE WD ADAPTER* 2 FTGXFE WD ADAPTER*1-1/2 CXFE WD ADAPTER* 1-1/2 X 1-1/4 CXFE WD ADAPTER*1-1/2 X 2 CXFE WD ADAPTER* 3 FTGXFE WD ADAPTER*2 C X FE WD ADAPTER* 2 X 1-1/2 CXFE WD ADAPTER*3 C X FE WD ADAPTER* 1/4 C X FE WP ADAPTER*3/8 C X FE WP ADAPTER* 3/8 X 1/4 CXFE WP ADAPTER*3/8 X 1/2 CXFE WP ADAPTER* 1/2 C X FE WP ADAPTER*1/2 X 1/4 CXFE WP ADAPTER* 1/2 X 3/8 CXFE WP ADAPTER*1/2 X 3/4 CXFE WP ADAPTER* 1/2 X 1 CXFE WP ADAPTER*5/8 X 1/2 CXFE WP ADAPTER* 5/8 X 3/4 CXFE WP ADAPTER*3/4 C X FE WP ADAPTER* 3/4 X 1/2 CXFE WP ADAPTER*3/4 X 1 CXFE WP ADAPTER* 3/4 X 1-1/4 CXFE WP ADAPTER*3/4 X 1-1/2 CXFE WP ADAPTER* 1 C X FE WP ADAPTER*1 X 1/2 CXFE WP ADAPTER* 1 X 3/4 CXFE WP ADAPTER*1 X 1-1/4 CXFE WP ADAPTER* 1 X 1-1/2 CXFE WP ADAPTER*1-1/4 C X FE WP ADAPTER* 1-1/4 C X 3/4 FE WP ADAPTER*1-1/4 X 1 CXFE WP ADAPTER* 1-1/4 X 1-1/2 CXFE WP ADAPTER*1-1/4 X 2 CXFE WP ADAPTER* 1/4 FTGXFE WP ADAPTER*3/8 FTGXFE WP ADAPTER* 3/8 X 1/4 FTGXFE WP ADAPTER*1/2 FTGXFE WP ADAPTER* 1/2 X 1/4 FTGXFE WP ADAPTER*1/2 X 3/8 FTG X FE ADAPTER* 1/2 FTG X 3/4 FE WP ADAPTER*3/4 FTGXFE WP ADAPTER* 3/4 FTG X 1/2 FE WP ADAPTER*1 FTGXFE WP ADAPTER* 1 FTG X 3/4 FE WP ADAPTER*1-1/4 FTGXFE WP ADAPTER* 1-1/2 FTGXFE WP ADAPTER*2 FTGXFE WP ADAPTER* 1-1/2 C X FE WP ADAPTER*2-1/2 FTGXFE WP ADAPTER* 1-1/2 C X 1 FE WP ADAPTER*1-1/2 X 1-1/4 CXFE WP ADAPTER* 1-1/2 X 2 CXFE WP ADAPTER*3 FTGXFE WP ADAPTER* 2 C X FE WP ADAPTER*2 X 1 C X FE WP ADAPTER* 2 X 1-1/4 CXFE WP ADAPTER*2 X 1-1/2 CXFE WP ADAPTER* 2-1/2 C X FE WP ADAPTER*3 C X FE WP ADAPTER*
1/2 X 3/8 FTGXM WP ADAPTER* 1/2 X 3/4 FTGXM WP ADAPTER*3/4 FTGXM WP ADAPTER* 3/4 X 1/2 FTGXM WP ADAPTER*1 FTGXM WP ADAPTER* 1 X 3/4 FTGXM WP ADAPTER*1-1/4 FTGXM WP ADAPTER* 1-1/2 FTGXM WP ADAPTER*2 FTGXM WP ADAPTER* 1-1/2 CXM WP ADAPTER*2-1/2 FTGXM WP ADAPTER* 1-1/2 X 1 CXM WP ADAPTER*1-1/2 X 1-1/4 CXM WP ADAPTER* 1-1/2 X 2 CXM WP ADAPTER*3 FTG X M WP ADAPTER* 2 CXM WP ADAPTER*2 X 1-1/4 CXM WP ADAPTER* 2 X 1-1/2 CXM WP ADAPTER*2 X 2-1/2 C X M WP ADAPTER* 2-1/2 CXM WP ADAPTER*2-1/2 X 2 CXM WP ADAPTER* 3 CXM WP ADAPTER*4 CXM WP ADAPTER* 1/2 X 3/4 C X HOSE WP ADAPTER*
1-1/4 X 2 CXSP CD FERRULE* 1-1/2 X 2 CXSP CD FERRULE*1-1/2 X 3 CXSP CD FERRULE* 2 CXSP CD FERRULE*2 X 3 CXSP CD FERRULE* 2 X 4 CXSP CD FERRULE*3 CXSP CD FERRULE* 3 X 4 CXSP CD FERRULE*4 CXSP CD FERRULE* 3 X 4 CXSP CD ECCENTRIC FERRULE*1-1/4 X 2 CXMJ CD ADAPTER* 1-1/4 X 3 CXMJ CD ADAPTER*1-1/2 X 2 CXMJ CD ADAPTER* 1-1/2 X 3 CXMJ CD ADAPTER*1-1/2 X 4 CXMJ CD ADAPTER* 2 X 3 CXMJ CD ADAPTER*2 X 4 CXMJ CD ADAPTER* 3 CXMJ CD ADAPTER*3 X 4 CXMJ CD ADAPTER* 4 CXMJ CD ADAPTER*6 C X M J CD ADAPTER* 1-1/4 FTGXSJ CD ADAPTER*4 ACT(3S)X1-1/2C-30 CD ROOF ADAPTER* 4 ACT(3S) X 2C-30 CD ROOF ADAPTER*4 SOIL(5A)X 1-1/2 C CD ROOF ADAPTER* 4 SOIL(5A)X 2 C CD ROOF ADAPTER*5ACT 4SX 3C CD ROOF ADAPT CALGARY* 5S X 3C CD ROOF ADAPT REGINA*1-1/2 SJXODX3/4M/1/2FE CD CONDENSATE TEE 2 C X SJ CD ADAPTER*2 C X MJ WD ADAPTER* 1-1/4 FE X SJ WD ADAPTER*1-1/2 FE X SJ WD ADAPTER* 1-1/2 X1-1/4 FE X SJ WD ADAPTER*1-1/4 FTG X SJ WD ADAPTER* 1-1/2 FTG X SJ WD ADAPTER*1-1/2 X 1-1/4 FTG X SJ ADAPTER* 1-1/4 M X SJ WD ADAPTER*1-1/2 M X SJ WD ADAPTER* 1-1/2 X 1-1/4 M X SJ WD ADAPTER*1-1/4 C X SJ WD ADAPTER* 1-1/4 X 1-1/2 CXSJ WD ADAPTER*1-1/2 C X SJ WD ADAPTER* 1-1/2 X 1-1/4 CXSJ WD ADAPTER*2 C X SJ WD ADAPTER* 1/2 CXM WP FLUSH VALVE ADAPTER*3/4 CXM WP FLUSH VALVE ADAPTER*
1-1/4 CXC 11-1/4 CD ELBOW* 1-1/2 CXC 11-1/4 CD ELBOW*2 CXC 11-1/4 CD ELBOW* 3 CXC 11-1/4 CD ELBOW*4 C X C 11-1/4 CD ELBOW* 1-1/4 CXC 22-1/2 CD ELBOW*1-1/2 CXC 22-1/2 CD ELBOW* 2 CXC 22-1/2 CD ELBOW*3 CXC 22-1/2 CD ELBOW* 4 CXC 22-1/2 CD ELBOW*3 FTGXC 45 CD ELBOW* 4 FTGXC 45 CD ELBOW*2 CXM CD 45 ELBOW* 1-1/4 CXC 45 CD ELBOW*1-1/2 CXC 45 CD ELBOW* 2 CXC 45 CD ELBOW*3 CXC 45 CD ELBOW* 4 CXC 45 CD ELBOW*1-1/4 CXC 60 CD ELBOW* 1-1/2 CXC 60 CD ELBOW*2 CXC 60 CD ELBOW* 3 CXC 60 CD ELBOW*4 CXC 60 CD ELBOW* 1-1/4 CXC CD 90 ELBOW*1-1/4 FTGXC CD 90 ELBOW* 1-1/2 FTGXC CD 90 ELBOW*2 FTGXC CD 90 ELBOW* 1-1/2 CXC CD 90 ELBOW*1-1/2 X 1-1/4 CXC CD 90 ELBOW* 3 CD FTGXC 90 ELBOW*4 FTGXC CD 90 ELBOW* 2 CXC CD 90 ELBOW*2X 1-1/4 CXC CD 90 ELBOW* 2 X 1-1/2 CXC CD 90 ELBOW*1-1/2 CXFE CD 90 ELBOW* 2 CXFE CD 90 ELBOW*1-1/2 CXM CD 90 ELBOW 2 CXM CD 90 ELBOW 3 CXC CD 90 ELBOW 4 CXC CD 90 ELBOW 1-1/2 CXSJ CD 90 ELBOW 1/2 X 1 CXC CP CLOSE RETURN BEND 3/4 1-3/8 CXC CP CLOSE RETURN BEND 1 X 1-3/4 CXC CP CLOSE RETURN BEND 1/2 C X M CP 45 ELBOW 3/4 C X M CP 45 ELBOW 1-1/4 C X M CP 45 ELBOW 4 CXC CP 45 ELBOW 6 CXC CP 45 ELBOW 1/2 C X C CP 90 ELBOW 1-1/4 CXC CP 90 ELBOW 1-1/4 X 1/2 CXC CP 90 ELBOW 1-1/4 X 3/4 CP 90 ELBOW 1-1/4 X 1 CP 90 ELBOW 1-1/2 X 1/2 CP 90 ELBOW 1-1/2 X 3/4 CXC CP 90 ELBOW 1-1/2 X 1 CXC CP 90 ELBOW 1/4 C X FE CP 90 ELBOW 1/2 CXFE CP 90 ELBOW 1/2 X 3/8 CXFE CP 90 ELBOW 1/2 X 3/4 CXFE CP 90 ELBOW 1/2 X 1 CXFE CP 90 ELBOW 3/4 CXFE CP 90 ELBOW 3/4 X 1/2 CXFE CP 90 ELBOW 3/4 X 1 CXFE CP 90 ELBOW 1 CXFE CP 90 ELBOW 1 X 1/2 C X FE CP 90 ELBOW 1 X 3/4 CXFE CP 90 ELBOW 1-1/4 CXFE CP 90 ELBOW 1-1/4 X 1/2 CXFE CP 90 ELBOW 1-1/4 X 3/4 CXFE CP 90 ELBOW 1-1/4 X 1 CXFE CP 90 ELBOW 2 X 3/4 CXC CP 90 ELBOW 2 X 1 CXC CP 90 ELBOW 2 X 1-1/4 CXC CP 90 ELBOW 1-1/2 CXFE CP 90 ELBOW 1-1/2 X 1 C X FE CP 90 ELBOW 2 CXFE CP 90 ELBOW 3 C X FE CP 90 ELBOW 1/2 CXFE CP 90 DROP EAR ELBOW
1/2 CXCXC CP DROP EAR TEE 1/2 CXCXFE CP TEE 1/2 X 1/2 X 1/4 CXCXFE CP TEE 1/2C X 1/2C X 3/8FE CP TEE 1/2 X 1/2 X 3/4 CXCXFE CP TEE 3/4 CXCXFE CP TEE 3/4C X 1/2C X 1/2FE CP TEE 3/4 X 1/2 X 3/4 CXCXFE CP TEE 3/4 X 3/4 X 3/8 CCFE CP TEE 3/4C X 3/4C X 1/2FE CP TEE 3/4 X 3/4 X 1 CXCXFE CP TEE 1 CXCXFE CP CP TEE 1 X 1 X 1/2 CXCXFE CP TEE 1 X 1 X 3/4 CXCXFE CP TEE 1-1/4 CXCXFE CP TEE 1-1/4 X 1-1/4 X 1/2 CCFE CP TEE 1-1/4 X 1-1/4 X 3/4 CCFE CP TEE 1-1/4X1-1/4X1 CCFE CP TEE 1-1/2 CXCXFE CP TEE 1-1/2X1-1/2X1/2 CCFE CP TEE 1-1/2 X 1-1/2 X 3/4 CCFE CP TEE 1-1/2 X 1-1/2 X 1 CCFE CP TEE 1/2 CXFEXFE CP TEE 1/2C X 3/4FE X 1/2FE CP TEE 3/4 C X FE X FE CP TEE 3/4 C X 3/4 FE X 1/2 FE CP TEE 2 CXCXFE CP TEE 2 X 2 X 1/2 CXCXFE CP TEE 2 X 2 X 3/4 CXCXFE CP TEE 2 X 2 X 1 CXCXFE CP TEE 1/2 CXCXFE CP DROP EAR TEE 3/4 CXCXFE CP DROP EAR TEE 3/4C X 3/4C X 1/2FE CP DROP EAR TEE 3/8 C X FE X C CP TEE 1/2 CXFEXC CP TEE 1/2C X 1/2FE X 3/4C CP TEE 1/2C X 3/4FE X 1/2C CP TEE 3/4 CXFEXC CP TEE 3/4 X 1/2 X 1/2 CXFEXC CP TEE 3/4C X 1/2FE X 3/4C CP TEE 3/4C X 3/4FE X 1/2C CP TEE 1 CXFEXC CP TEE 1C X 1/2FE X 1C CP TEE 1 X 3/4 X 1 CXFEXC CP TEE 1-1/4 CXFEXC CP TEE 1-1/4 X 1/2 X 1-1/4 CXFEXC CP TEE 1-1/4 X 3/4 X 1-1/4 CXFEXC CP TEE 1-1/2 C X FE X C CP TEE 1-1/2X1/2X1-1/2 CXFEXC CP TEE 1-1/2X3/4X1-1/2 CXFEXC CP TEE 1/2 FEXFEXC CP TEE 3/4 FEXFEXC CP TEE 3/4FE X 1/2FE X 1/2C CP TEE 3/4FE X 1/2FE X 3/4C CP TEE 3/4FE X 3/4FE X 1/2C CP TEE 2 C X FE X C CP TEE 2 X 1/2 X 2 CXFEXC CP TEE 2 X 3/4 X 2 CXFEXC CP TEE
1/2FE X 3/4M X 1/2C CP TEE 1/2 CXCXCXC CP CROSS*3/4 CXCXCXC CP CROSS* 1 CXCXCXC CP CROSS*1-1/2 CXCXCXC CP CROSSES* 2 CXCXCXC CP CROSS*3/4 CXFTGXC CP TEE* 2 X 2 X 3 CXCXC CP TEE*2-1/2 X 1/2 X 2-1/2 CP TEE* 2-1/2 X 1-1/2 X 1-1/2 CP TEE*5 CXCXC CP TEE* 5 X 5 X 3 CXCXC CP TEE*6 CXCXC CP TEE* 3/4FE X 1/8 FE X 3/4C WP BASEBOARD TEE*1/8 CXCXC WP TEE* 1/4 CXCXC WP TEE*3/8 CXCXC WP TEE* 1/2 CXCXC WP TEE*1/2 X 1/2 X 3/4 CXCXC WP TEE* 3/4 CXCXC WP TEE*3/4 X 1/2 X 1/2 CXCXC WP TEE* 3/4 X 1/2 X 3/4 CXCXC WP TEE*3/4 X 3/4 X 1/4 CXCXC WP TEE* 3/4C X 3/4C X 3/8C CXCXC WP TEE*3/4 X 3/4 X 1/2 CXCXC WP TEE* 1 CXCXC WP TEE*1 X 1/2 X 1/2 CXCXC WP TEE* 1 X 1/2 X 3/4 CXCXC WP TEE*1 X 1/2 X 1 CXCXC WP TEE* 1 X 3/4 X 1/2 CXCXC WP TEE*1 X 3/4 X 3/4 CXCXC WP TEE* 1 X 3/4 X 1 CXCXC WP TEE*1 X 1 X 3/8 CXCXC WP TEE* 1 X 1 X 1/2 CXCXC WP TEE*1 X 1 X 3/4 CXCXC WP TEE* 1-1/4 CXCXC WP TEE*1-1/4 X 1/2 X 1/2 CXCXC WP TEE* 1-1/4 X 1/2 X 3/4 CXCXC WP TEE*1-1/4 X 1/2 X 1 CXCXC WP TEE* 1-1/4 X 1/2 X 1-1/4 CXCXC WP TEE*1-1/4 X 3/4 X 1/2 CXCXC WP TEE* 1-1/4 X 3/4 X 3/4 CXCXC WP TEE*1-1/4 X 3/4 X 1 CXCXC WP TEE* 1-1/4 X 3/4 X 1-1/4 CXCXC WP TEE*1-1/4 X 1 X 1/2 CXCXC WP TEE* 1-1/4 X 1 X 3/4 CXCXC WP TEE*1-1/4 X 1 X 1 CXCXC WP TEE* 1-1/4 X 1 X 1-1/4 CXCXC WP TEE*1-1/4 X 1-1/4 X 1/2 CXCXC WP TEE* 1-1/4 X 1-1/4 X 3/4 CXCXC WP TEE*1-1/4C X 1-1/4C X 1C CXCXC WP TEE* 1-1/2 CXCXC CXCXC WP TEE*1-1/2 X 1/2 X 1/2 CXCXC WP TEE* 1-1/2 X 1/2 X 3/4 CXCXC WP TEE*1-1/2 X 1/2 X 1 CXCXC WP TEE* 1-1/2 X 1/2 X 1-1/4 CXCXC WP TEE*1-1/2 X 1/2 X 1-1/2 CXCXC WP TEE* 1-1/2 X 3/4 X 1/2 CXCXC WP TEE*1-1/2 X 3/4 X 3/4 CXCXC WP TEE* 1-1/2 X 3/4 X 1 CXCXC WP TEE*1-1/2 X 3/4 X 1-1/4 CXCXC WP TEE* 1-1/2 X 3/4 X 1-1/2 CXCXC WP TEE*1-1/2 X 1 X 1/2 CXCXC WP TEE* 1-1/2 X 1 X 3/4 CXCXC WP TEE*1-1/2 X 1 X 1 CXCXC WP TEE* 1-1/2 X 1 X 1-1/4 CXCXC WP TEE*1-1/2 X 1 X 1-1/2 CXCXC WP TEE* 1-1/2 X 1-1/4 X 1/2 CXCXC WP TEE*1-1/2 X 1-1/4 X 3/4 CXCXC WP TEE* 1-1/2 X 1-1/4 X 1 CXCXC WP TEE*1-1/2 X 1-1/4 X 1-1/4 CXCXC WP TEE* 1-1/2 X 1-1/4 X 1-1/2 CXCXC WP TEE*1-1/2 X 1-1/2 X 1/2 CXCXC WP TEE* 1-1/2 X 1-1/2 X 3/4 CXCXC WP TEE*1-1/2 X 1-1/2 X 1 CXCXC WP TEE* 1-1/2 X 1-1/2 X 1-1/4 CXCXC WP TEE*2 CXCXC CXCXC WP TEE* 2 X 1/2 X 2 CXCXC WP TEE*2 X 3/4 X 2 CXCXC WP TEE* 2 X 1 X 3/4 CXCXC WP TEE*2 X 1 X 1 CXCXC WP TEE* 2C X 1C X 1-1/4C CXCXC WP TEE*2 X 1 X 1-1/2 CXCXC WP TEE* 2 X 1 X 2 CXCXC WP TEE*
2 X 1-1/4 X 1/2 CXCXC WP TEE* 2 X 1-1/4 X 3/4 CXCXC WP TEE*2 X 1-1/4 X 1 CXCXC WP TEE* 2 X 1-1/4 X 1-1/4 CXCXC WP TEE*2 X 1-1/4 X 1-1/2 CXCXC WP TEE* 2 X 1-1/4 X 2 CXCXC WP TEE*2 X 1-1/2 X 1/2 CXCXC WP TEE* 2 X 1-1/2 X 3/4 CXCXC WP TEE*2 X 1-1/2 X 1 CXCXC WP TEE* 2 X 1-1/2 X 1-1/4 CXCXC WP TEE*2 X 1-1/2 X 1-1/2 CXCXC WP TEE* 2 X 1-1/2 X 2 CXCXC WP TEE*2 X 2 X 1/2 CXCXC WP TEE* 2 X 2 X 3/4 CXCXC WP TEE*2 X 2 X 1 CXCXC WP TEE* 2 X 2 X 1-1/4 CXCXC WP TEE*2 X 2 X 1-1/2 CXCXC WP TEE* 2-1/2 CXCXC WP TEE*2-1/2 X 1/2 X 2-1/2 CXCXC WP TEE* 2-1/2 X 3/4 X 1-1/2 CXCXC WP TEE*2-1/2 X 3/4 X 2-1/2 CXCXC WP TEE* 2-1/2 X 1 X 1-1/4 CXCXC WP TEE*2-1/2 X 1 X 1-1/2 CXCXC WP TEE* 2-1/2 X 1 X 2 CXCXC WP TEE*2-1/2 X 1 X 2-1/2 CXCXC WP TEE* 2-1/2 X 1-1/4 X 1-1/4CXCXC WP TEE*2-1/2 X 1-1/4 X 1-1/2 CXCXC WP TEE* 2-1/2 X 1-1/4 X 2 CXCXC WP TEE*2-1/2 X 1-1/4 X 2-1/2 CXCXC WP TEE* 2-1/2 X 1-1/2 X 1 CXCXC WP TEE*2-1/2 X 1-1/2 X 1-1/4 CXCXC WP TEE* 2-1/2 X 1-1/2 X 1-1/2 CXCXC WP TEE*2-1/2 X 1-1/2 X 2 CXCXC WP TEE* 2-1/2 X 1-1/2 X 2-1/2 CXCXC WP TEE*2-1/2 X 2 X 1/2 CXCXC WP TEE* 2-1/2 X 2 X 3/4 CXCXC WP TEE*2-1/2 X 2 X 1 CXCXC WP TEE* 2-1/2 X 2 X 1-1/4 CXCXC WP TEE*2-1/2 X 2 X 1-1/2 CXCXC WP TEE* 2-1/2 X 2 X 2 CXCXC WP TEE*2-1/2 X 2 X 2-1/2 CXCXC WP TEE* 2-1/2 X 2-1/2 X 1/2 CXCXC WP TEE*2-1/2 X 2-1/2 X 3/4 CXCXC WP TEE* 2-1/2 X 2-1/2 X 1 CXCXC WP TEE*2-1/2 X 2-1/2 X 1-1/4 CXCXC WP TEE* 2-1/2 X 2-1/2 X 1-1/2 CXCXC WP TEE*2-1/2 X 2-1/2 X 2 CXCXC WP TEE* 3 CXCXC WP TEE*3 X 3/4 X 3 CXCXC WP TEE* 3 X 1 X 3 CXCXC WP TEE*3 X 1-1/4 X 3 CXCXC WP TEE* 3 X 1-1/2 X 1-1/4 CXCXC WP TEE*3 X 1-1/2 X 1-1/2 CXCXC WP TEE* 3 X 1-1/2 X 2-1/2 CXCXC WP TEE*3 X 1-1/2 X 3 CXCXC WP TEE* 3 X 2 X 1/2 CXCXC WP TEE*3 X 2 X 1 CXCXC WP TEE* 3 X 2 X 1-1/4 CXCXC WP TEE*3 X 2 X 1-1/2 CXCXC WP TEE* 3 X 2 X 2 CXCXC WP TEE*3 X 2 X 2-1/2 CXCXC WP TEE* 3 X 2 X 3 CXCXC WP TEE*3 X 2-1/2 X 3/4 CXCXC WP TEE* 3 X 2-1/2 X 1 CXCXC WP TEE*3 X 2-1/2 X 1-1/4 CXCXC WP TEE* 3 X 2-1/2 X 1-1/2 CXCXC WP TEE*3 X 2-1/2 X 2 CXCXC WP TEE* 3 X 2-1/2 X 2-1/2 CXCXC WP TEE*3 X 2-1/2 X 3 CXCXC WP TEE* 3 X 3 X 1/2 CXCXC WP TEE*3 X 3 X 3/4 CXCXC WP TEE* 3 X 3 X 1 CXCXC WP TEE*3 X 3 X 1-1/4 CXCXC WP TEE* 3 X 3 X 1-1/2 CXCXC WP TEE*3 X 3 X 2 CXCXC WP TEE* 3 X 3 X 2-1/2 CXCXC WP TEE*4 CXCXC WP TEE* 4 X 1-1/2 X 3 CXCXC WP TEE*4 X 2 X 2 CXCXC WP TEE* 4 X 2 X 3 CXCXC WP TEE*4 X 2-1/2 X 2-1/2 CXCXC WP TEE* 4 X 2-1/2 X 3 CXCXC WP TEE*4 X 3 X 2 CXCXC WP TEE* 4 X 3 X 2-1/2 CXCXC WP TEE*
4 X 3 X 3 CXCXC WP TEE* 4 X 4 X 1/2 CXCXC WP TEE*4 X 4 X 3/4 CXCXC WP TEE* 4 X 4 X 1 CXCXC WP TEE*4 X 4 X 1-1/4 CXCXC WP TEE* 4 X 4 X 1-1/2 CXCXC WP TEE*4 X 4 X 2 CXCXC WP TEE* 4 X 4 X 2-1/2 CXCXC WP TEE*4 X 4 X 3 CXCXC WP TEE* 5 X 5 X 2 CXCXC WP TEE*
2-1/2 CXFE CP UNION* 2-1/2 CXC CP UNION*2 CXM CP UNION* 2-1/2 C X M CP UNION*3 CXC CP UNION* 3/4 CXM CP UNION ELBOW 3/4 CXC WP UNION* 1 CXC WP UNION*1-1/4 CXC WP UNION* 1-1/2 C X C WP UNION*1/2 C X FE WP UNION* 3/4 C X FE WP UNION*1 C X FE WP UNION* 2 CXC WP UNION*1-1/4 C X FE WP UNION* 1-1/2 C X FE WP UNION*2 C X FE WP UNION* 1/2 C X M WP UNION*3/4 C X M WP UNION* 1 C X M WP UNION*1-1/4 C X M WP UNION* 1-1/2 C X M WP UNION*2 C X M WP UNION*
1-1/4 CXC CD P-TRAP BODY N/CO 1-1/2 C X C CD P-TRAP BODY N/CO 2 C X C CD P-TRAP BODY N/CO 3 C X C CD P-TRAP BODY N/CO 1-1/4 CD P TRAP - N/CO 1-1/4 CD P TRAP-N/CO- ELBOW 1-1/2 P TRAP - N/CO- 1-1/2 CD P TRAP-N/CO-ELBOW 2 CD P TRAP - N/CO 2 CD P TRAP-N/CO-ELBOW 3 CD P TRAP - N/CO 3 CD P TRAPS-N/CO-ELBOW 1 1/4 CD S TRAP N/CO 1 1/2 CD S TRAP N/CO 1-1/4 CD S TRAP - W/CO 1-1/2 CD S TRAP - W/CO 2 CD S TRAP W/CO 1-1/2 C X C CD P-TRAP BODY - W/CO 2 C X C CD P-TRAP BODY - W/CO 1-1/4 CD P TRAP - W/CO 1-1/4 CD P TRAP-W/CO-ELBOW 1-1/2 CD P TRAP W/CO 1-1/2 CD P TRAP-W/CO-ELBOW 2 CD P TRAP - W/CO 2 CD P TRAP-W/CO-ELBOW 3 CD P TRAP - W/CO 3 CD P TRAP-W/CO-ELBOW 3 X 6 X 1-1/2 X 1-1/2 CD DRUM TRAP 1-1/2 CD P TRAP L/CO GROUND SWIVEL 1-1/2 CD P TRAP W/CO GROUND SWIVEL
1-1/4 CXCXCXC CD DOUBLE WASTE FTG 1-1/2 CXCXCXC CD DOUBLE WASTE FTG 1-1/2 1-1/4 1-1/4 1-1/4 CXCXCXC CD DOUBLE WASTE FTG 1-1/2 1-1/4 1-1/2 1-1/2 CXCXCXC CD DOUBLE WASTE FTG 1-1/2 1-1/2 1-1/4 1-1/4 CXCXCXC CD DOUBLE WASTE FTG 2 1-1/2-1-1/4-1-1/4 CXCXCXC CD DOUBLE WASTE FTG
2 1-1/2 1-1/2 1-1/2 CXCXCXC CD DOUBLE WASTE FTG 1-1/4 CXCXC CD TY*1-1/2 CXCXC CD TY* 1-1/2 X 1-1/4 X 1-1/4 CXCXC CD TY*1-1/2 X 1-1/4 X 1-1/2 CXCXC CD TY* 1-1/2 X 1-1/2 X 1-1/4 CXCXC CD TY*3 FTG X C X C CD TY* 3 X 3 X 1-1/4 FTGXCXC CD TY*3 X 3 X 1-1/2 FTGXCXC CD TY* 3 X 3 X 2 FTGXCXC CD TY*2 CXCXC CD TY* 2 X 1-1/4 X 1-1/4 CXCXC CD TY*2 X 1-1/4 X 1-1/2 CXCXC CD TY* 2 X 1-1/4 X 2 CXCXC CD TY*2 X 1-1/2 X 1-1/4 CXCXC CD TY* 2 X 1-1/2 X 1-1/2 CXCXC CD TY*2 X 1-1/2 X 2 CXCXC CD TY* 2 X 2 X 1-1/4 CXCXC CD TY*2 X 2 X 1-1/2 CXCXC CD TY* 1-1/2 CXCXFE CD TY*2 CXCXFE CD TY 2 X 1-1/2 X 1-1/2 CXCXF CD TY 3 CXCXC CD TY* 3 X 1-1/2 X 1-1/4 CXCXC CD TY*3 X 2 X 1-1/2 CXCXC CD TY* 3 X 3 X 1-1/4 CXCXC CD TY*3 X 3 X 1-1/2 CXCXC CD TY* 3 X 3 X 2 CXCXC CD TY*4 CXCXC CD TY* 4 X 4 X 1-1/2 CXCXC CD TY*4 X 4 X 2 CXCXC CD TY* 4 X 4 X 3 CXCXC CD TY*1-1/4 CXCXCXC CD DOUBLE TY 1-1/2 CXCXCXC CD DOUBLE TY 1-1/2 1-1/2 1-1/4 1-1/4 CXCXCXC CD DOUBLE TY 1-1/2 1-1/4 1-1/4 1-1/4 CXCXCXC CD DOUBLE TY 2 CXCXCXC CD DOUBLE TY 2 X 2 X 1-1/4 X 1-1/4 CXCXCXC CD DOUBLE TY 2 X 2 X 1-1/2 X 1-1/2 CXCXCXC CD DOUBLE TY 3 CXCXCXC CD DOUBLE TY 3 X 3 X 1-1/4 X 1-1/4 CXCXCXC CD DOUBLE TY 3 X 3 X 1-1/2 X 1-1/2 CXCXCXC CD DOUBLE TY 3 X 3 X 2 X 2 CXCXCXC CD DOUBLE TY 4 CXCXCXC CD DOUBLE TY 4 X 4 X 2 X 2 CXCXCXC CD DOUBLE TY 4 X 4X 3 X 3 CXCXCXC CD DOUBLE TY 1-1/4 CXCXCXC CD DOUBLE LONG TURN TY 1-1/2 CXCXCXC CD DOUBLE LONG TURN TY 1-1/2 1-1/2 1-1/4 1-1/4 CXCXCXC CD DLT TY 2 CXCXCXC CD DOUBLE LONG TURN TY 2 X 2 X 1-1/4 X 1-1/4 CXCXCXC CD DLT TY 2 X 2 X 1-1/2 X 1-1/2 CXCXCXC CD DLT TY 1-1/2 CXCXC LONG TURN CD TY 2 CXCXC LONG TURN CD TY 3X3X3X1-1/2 CXCXCXC SIDEOUT RH CD TY 3X3X3X1-1/2 CXCXCXC SIDEOUT LH CD TY
1-1/4 CXCXC CD 45 Y* 1-1/2 CXCXC CD 45 Y*1-1/2CX 1-1/4CX 1-1/4C CD 45 Y* 1-1/2CX 1-1/4CX 1-1/2C CD 45 Y*1-1/2CX 1-1/2CX 1-1/4C CD 45 Y* 2 CXCXC 45 CD Y*2CX 1-1/4CX 1-1/4C CD 45 Y* 2CX 1-1/4CX 1-1/2C CD 45 Y*2CX 1-1/4CX 2C CD 45 Y* 2CX 1-1/2CX 1-1/4C CD 45 Y*2CX 1-1/2CX 1-1/2C CD 45 Y* 2CX 1-1/2CX 2C CD 45 Y*2CX 2CX 1-1/4C CD 45 Y* 2CX 2CX 1-1/2C CD 45 Y*3 CXCXC CD 45 Y* 3C X 2C X 2C CD 45 Y*3CX 3CX 1-1/4C CD 45 Y* 3CX 3CX 1-1/2C CD 45 Y*3CX 3CX 2C CD 45 Y* 4 CXCXC CD 45 Y*4CX 4CX 2C CD 45 Y* 4CX 4CX 3C CD 45 Y*1-1/4 CXCXCXC CD 45 DOUBLE Y 1-1/2 CXCXCXC CD 45 DOUBLE Y 1-1/2 1-1/2 1-1/4 1-1/4 CXCXCXC CD DOUBLE Y 2 CXCXCXC CD 45 DOUBLE Y 2 X 2 X 1-1/4 X 1-1/4 CXCXCXC CD DOUBLE Y 2 X 2 X 1-1/2 X 1-1/2 CXCXCXC CD DOUBLE Y 3 CXCXCXC CD 45 DOUBLE Y 3 X 3 X 1-1/2 X 1-1/2 CXCXCXC CD DOUBLE Y
5 CP TUBE END CAP* 6 CP TUBE END CAP*1-1/2 CXC/O CD TUBE END CLEANOUT* 3 CD CXC/O TUBE END CLEANOUT*3 FTGXC/O CD CLEANOUT - FLUSH TYPE* 4 FTGXC/O CD CLEANOUT - FLUSH TYPE*1-1/4 FTGXC/O CD CLEANOUT - FULL PLUG* 1-1/2 FTGXC/O CD CLEANOUT - FULL PLUG*2 FTGXC/O CD CLEANOUT - FULL PLUG* 3 FTGXC/O CD CLEANOUT - FULL PLUG*4 FTGXC/O CD CLEANOUT - FULL PLUG* 1-1/4 CXCXCO CD LINE CLEANOUT 1-1/2 CXCXCO CD LINE CLEANOUT 2 CXCXCO CD LINE CLEANOUT 3 CXCXCO CD LINE CLEANOUT 4 CXCXCO CD LINE CLEANOUT 1-1/2 CXCXCO CLEANOUT-FULL PLUG 2 CXCXCO CD CLEANOUT - FULL PLUG 3 CXCXCO CD CLEANOUT - FULL PLUG 1-1/4 CXCO WD TUBE END CLEANOUT*1-1/2 CXCO WD TUBE END CLEANOUT* 2 CXCO WD TUBE END CLEANOUT*3 CXCO WD TUBE END CLEANOUT* 1-1/4 WD FLUSH FTGXCO CLEANOUT*1-1/2 FTGXCO WD CLEANOUT-FLUSH TYPE* 1-1/2 X 1 FTGXCO WD CLEANOUT - FLUSH*2 FTGXCO WD CLEANOUT-FLUSH TYPE* 1-1/4 FTGXCO WD CLEANOUT FULL PLUG*1-1/2 FTGXCO WD CLEANOUT FULL PLUG* 2 FTGXCO WD CLEANOUT FULL PLUG*
Associated Firms: Firms that are related to each other in any manner other than through an arm’s length (independent)customer/supplier relationship. For example, firms are associated or related if an officer or director ofone firm is an officer or director of the other, if a firm directly or indirectly owns, holds or controlsshares of the other firm, or if a firm is the exclusive distributor for another firm.
Delivery Costs: The average delivery costs (freight, handling and insurance) from the point of direct shipment inCanada to your customers, whether included in the selling value or incurred separately by yourcustomers, expressed as a percentage of the net delivered purchase or selling value. If the goods aresold on an FOB basis (ex-factory), please provide your best estimate of the delivery costs incurred byyour customers.
Period of Review: This expiry review covers the period from January 1, 2013, to March 31, 2016.
Practical Plant Capacity: This is the greatest level of output from the machinery and equipment used in the production of steelgrating that your plants can achieve on a continuous basis within the framework of a realistic workpattern. Consideration should be given to the typical product mix, number of shifts per day, annualoperating days, etc., over the past five years.
If yes, please complete this page and all parts of this questionnaire. If no, please return only this completed page as per the directives provided in the yellow "Introduction" tab.
Firm Name: (in English and French, if applicable)Firm Address:
Telephone Number:Fax Number:
E-mail Address:Web Site Address:
Signature of Authorized Official
Name of Authorized Official
Title of Authorized Official
E-mail Address Web Site Address
CERTIFICATION
During the period of review (January 1, 2013, to March 31, 2016), did your firm produce or export copper pipe fittings? Please select one response from the pull down menu.
The undersigned certifies that the information herein supplied is complete and correct to the best of his/her knowledge and belief.
i) Firm Name:Firm Address:Percent Share of Ownership:
ii) Firm Name:Firm Address:Percent Share of Ownership:
iii) Firm Name:Firm Address:Percent Share of Ownership:
P2.
i) Firm Name:Firm Address:Percent Share of Ownership:
ii) Firm Name:Firm Address:Percent Share of Ownership:
iii) Firm Name:Firm Address:Percent Share of Ownership:
P3.
i) Plant No. 1: Plant Location:Product Lines:Plant Produces copper pipe fittings for the Canadian Market:Plant is Capable of Producing copper pipe fittings for the Canadian Market:
ii) Plant No. 2: Plant Location:Product Lines:Plant Produces copper pipe fittings for the Canadian Market:Plant is Capable of Producing copper pipe fittings for the Canadian Market:
iii) Plant No. 3: Plant Location:Product Lines:Plant Produces copper pipe fittings for the Canadian Market:Plant is Capable of Producing copper pipe fittings for the Canadian Market:
Please provide the following information associated with your firm's production capabilities, by facility.
PART I - PUBLIC INFORMATION
Information requested in this part is public or non-confidential. If the response to any question would divulge confidential business information, provide a redacted version for the public/non-confidential record and a complete version that will be placed on the confidential record.
If your firm is wholly or partly owned by other firms involved in any manner with copper pipe fittings, whether upstream or downstream, please list the names and addresses of these firms, and indicate the percent share of ownership or interest that they hold.
If your firm wholly or partly owns other firms involved in any manner with copper pipe fittings, whether upstream or downstream, please list their names and addresses, and indicate the extent of your firm’s ownership or interest in those firms.
P4. Please indicate whether any of your firm's plants that are not currently capable of producing copper pipe fittings for the Canadian market could be converted to do so. If so, what modifications would be necessary?
P5. If your firm permanently closed, shut down or otherwise disposed of any plants or product lines, discontinued any processes affecting its production of copper pipe fittings or made any significant asset disposals since January 1, 2013, please indicate the action taken and the date, location and reasons for such action.
P6. Please describe your firm's marketing practices with regard to its export sales of copper pipe fittings.
P7. If your firm published an annual report to shareholders in each year since 2013, please provide either a photocopy-ready copy or an electronic copy of each one.
Information requested in this part is public. If the response to any question would divulge confidential business information, provide a redacted version and a complete version to be placed on the confidential record.
Should your firm wish to add any comments related to the Public Information questions, you may do so below. Please be sure to indicate the question being commented on.
CONFIDENTIAL COPPER PIPE FITTINGSRR-2015-003
FOREIGN PRODUCERS' QUESTIONNAIRE
copper pipe fittings
C1. Please provide your firm's practical plant capacity, inventories, production, imports and sales of copper pipe fittings produced in its home country.
Please answer this question by completing Schedule 1 in the green "CapProdImpSales" tab.
C2. Please provide the following estimations:
Your firm's sales volume of copper pipe fittings as a percentage of its total sales volume in 2015
placeholder
Your firm's sales value of copper pipe fittings as a percentage of its total sales value in 2015
placeholder
C3. Please provide the following estimation:
Your firm's percentage share of its home country's total production of copper pipe fittings in 2015
placeholder
C4. Please provide the following estimation:
Your firm's percentage share of its home country's total volume of exports of copper pipe fittings in 2015
placeholder
C5. Does your firm have any plans to expand, curtail or shut down its practical plant capacity and/or production of copper pipe fittings in 2016 or 2017?
If so, please describe those plans, including target dates and capacity/production quantities, list the plants involved and give the reasons for the change.
C6.
Firm Name:Firm Address:
Firm Name:Firm Address:
Firm Name:Firm Address:
Firm Name:Firm Address:
Firm Name:Firm Address:
Firm Name:Firm Address:
PART II - CONFIDENTIAL INFORMATION
Information requested in this part is considered to be confidential in nature and will be treated as such, in accordance with sections 43 to 49 of the Canadian International Trade Tribunal Act .
Please provide the names and addresses of the Canadian importers of your firm's copper pipe fittings in each calendar year from 2013 to 2015.
CONFIDENTIAL COPPER PIPE FITTINGSRR-2015-003
FOREIGN PRODUCERS' QUESTIONNAIRE
C7. Please identify your firm's principal export markets, other than Canada, for copper pipe fittings from 2013 to 2015, inclusive.
C8. Please report your firm's volumes and values of finished inventories of copper pipe fittings produced for the Canadian market for the years requested.
Please answer this question by completing Schedule 2 in the green "Inventories" tab.
C9. Has your firm maintained any inventories of copper pipe fittings in Canada since 2013?
If so, please answer this question by completing Schedule 3 in the green "Inventories" tab.
C10.
· production,· purchases from other sources and from importers,· imports,· home market sales from production, · market size and growth, · market share, · price levels, · financial performance, · export sales,
· capacity and utilization levels, and · investments.
C11. Please explain how freight costs are established by your firm. Please include the methodology behind pricing, terms of billing, payment, delivery mode and schedule, etc. Include any information that would be relevant to how freight is treated by your firm (including calculation).
FREIGHT COSTS
In a separate file, please provide the rationale and assumptions underlying any plans and forecasts, and indicate whether the plans and forecast were prepared internally or by an outside consultant.
Note: These specific plans and forecasts may already be in the form of business plans or equivalent documents used by your firm. If these types of documents are readily available, you may submit them in lieu of the above. However, if no formal forecast documents exist, provide your firm’s best estimates with regard to the above-mentioned factors.You are not required to provide your firm’s plans and forecasts dealing with products or activities other than copper pipe fittings.
Please provide any documents, plans, forecasts, market analyses or other information setting out your firm’s strategies and objectives, for the years 2016 and 2017, concerning copper pipe fittings it produces and other products it makes on the same equipment, with respect to the following factors:
· any change in product mix of production, and home market and export sales,
CONFIDENTIAL COPPER PIPE FITTINGSRR-2015-003
FOREIGN PRODUCERS' QUESTIONNAIRE
Jan. 1 - Mar. 31, Jan. 1 - Mar. 31,2013 2014 2015 2015 2016
Practical Plant CapacityBeginning Inventory of Copper Pipe Fittings - - - - Total Production of Copper Pipe FittingsTotal Production of Other Products produced on the same equipment
Imports/Domestic Purchases of Copper Pipe FittingsHome Market Sales of Copper Pipe FittingsExport Sales to: Canada United States Other Countries
Country 1: Please specify Country 2: Please specify Country 3: Please specify All Other Countries
Total Exports of Copper Pipe Fittings - - - - - Total Sales of Copper Pipe Fittings - - - - - Ending Inventory of Copper Pipe Fittings
(*) If your firm's actual ending inventory that you provided at line 28 differs from the calculated ending inventory at line 30 (calculated using the formula "ending inventory = beginning inventory + imports - domestic sales - export sales") please explain the reasons for the difference.
Schedule 1 (Question C1) - Practical Plant Capacity, Inventories, Production, Imports and Sales of Copper Pipe Fittings Produced by Your Firm in Your Home Country
(Volume in Pieces)
CONFIDENTIAL COPPER PIPE FITTINGSRR-2015-003
FOREIGN PRODUCERS' QUESTIONNAIRE
Schedule 2 (Questions C8) - Finished Inventories Produced for the Canadian Market
Finished Inventories Produced for the Canadian Market
Volume (Pieces) Value (CAD$)Average Unit Value
(CAD$/Piece)
2013 - 2014 - 2015 - 2016 -
Schedule 3 (Question C9) - Finished Inventories Maintained in Canada
Finished Inventories Maintained in Canada
Volume (Pieces)201420152016
CONFIDENTIAL COPPER PIPE FITTINGSRR-2015-003
FOREIGN PRODUCERS' QUESTIONNAIRE
Question number:
Question number:
Question number:
Question number:
CONFIDENTIAL INFORMATION COMMENTS
Information requested in this part is considered to be confidential in nature and will be treated as such, in accordance with sections 43 to 49 of the Canadian International Trade Tribunal Act .
Should your firm wish to add any comments related to the Confidential Information questions, you may do so below. Please be sure to indicate the question being coimented on.
