QATAR INDUSTRIAL LABORATORIES W - qilqatar.comqilqatar.com/_doc/ias-cert-2017.pdf · This...

This is to attest that

QATAR INDUSTRIAL LABORATORIES W.LL INDUSTRIAL AREA, ST. NO. 43

GATE 127, P.O. BOX 10415 DOHA, QATAR

Testing Laboratory TL-528

has met the requirements of AC89, IAS Accreditation Criteria for Testing Laboratories, and has demonstrated compliance with ISO/IEC Standard 17025:2005, General requirements for the competence of testing and calibration laboratories. This organization is accredited to provide the services specified in the scope of accreditation maintained on the IAS website (www.iasonline.org).

This certificate is valid up to August 1, 2018.

This accreditation certificate supersedes any IAS accreditation bearing an earlier effective date. The certificate becomes invalid upon suspension, cancellation or revocation of accreditation. See www.iasonline.org for current accreditation information, or contact IAS at 562-364-8201.

C.P. Ramani, P.E., C.B.O President

International Accreditation Service, Inc. 3060 Saturn Street, Suite 100, Brea, California 92821 U.S.A

Telephone +1 562-364-8201 — [email protected] www.iasonline.org Page 1 of 31

IAS Accreditation Number TL-528 Company Name Qatar Industrial Laboratories W.LL Address Industrial Area, St. No. 43

Gate 127, P.O. Box 10415 Doha, Qatar

Contact Name Mr. Fasee Ahmed, Manager Mr. Shaikh Rafique, QA/QC Manager Mr. Kunhammad Ayakkandi, Senior Technician

Telephone +974 50726408 / 70186899 Effective Date of Scope July 27, 2017 Accreditation Standard ISO/IEC 17025:2005

CATEGORY STD. NO./

METHOD/ISSUE DATES

TITLE OF STD./METHOD USED AND IT’S RELEVANT

SECTION

LOCATION/ FACILITY

TEST EQUIPMENT/ INSTRUMENTATION

USED (NAME/ID NO.)

NAMES OF APPROVED

OPERATORS/ TECHNICIANS

Aggregate ASTM C136/C136M-15

Standard Test Method for Sieve Analysis of Fine and Coarse Aggregates

Doha Laboratory

1- Balance S/N: Q/BL/029 2- Sieves S/N: Q/SV/072, Q/SV/070, Q/SV/071, Q/SV/198, QSV/293, Q/SV/294 3- Oven S/N: 14E133

Shakul M-019 Rahoof-M-099

BS EN 933-1:2012 Tests for geometrical properties of aggregates. Determination of particle size distribution. Sieving method

Doha Laboratory

1- Balance S/N: Q/BL/029 2- Test sieves S/N: QIL/SV/024, Q/SV/106, Q/SV/026, Q/SV/027, Q/SV/013, Q/SV/029, Q/SV/030, Q/SV/207, Q/SV/006, Q/SV/033 3- Oven S/N: 14E133 4- Trays 5- Sieve shaker

Doss M-121 Sherin M-144

BS 812 - 109-1990 Testing aggregates. Methods for determination of moisture content

Doha Laboratory

1- Balance S/N: Q/BL/029 2- Container 3- Oven S/N: 14E133 4- Scoop 5- Thermometer S/N: 140501865

Shibi-M-065 Doss M-121

mailto:[email protected]

http://www.iasonline.org/

TL-528 Page 2 of 31 Qatar Industrial Laboratories, W.L.L.

CATEGORY STD. NO./

METHOD/ISSUE DATES


SECTION

LOCATION/ FACILITY


USED (NAME/ID NO.)

NAMES OF APPROVED


Aggregate ASTM C128-15 Standard Test Method for Relative Density (Specific Gravity) and Absorption of Fine Aggregate

Doha Laboratory

1- Balance S/N: Q/BL/029 and Q/BL/011 2- Oven S/N: 14E133 3- Wire basket 4- Air tight container 5- Sieves S/N: Q/SV/072, Q/SV/070, Q/SV/071, Q/SV/198, QSV/293, Q/SV/294 6- Buoyancy table

Doss M-121 Safihan M-146

ASTM C127-15 Determination of density, relative density and absorption of coarse aggregate

Doha Laboratory

1- Water tight container 2- Balance S/N: Q/BL/029 and Q/BL/011 3- Oven S/N: 14E133 4- Thermometer S/N: 140501865 5- Scoop 6- Glass plate 7- Gas jar 8- Pycnometer S/N: QIL/SG/C701 9- Vacuum desiccator


ASTM C142-10 Standard Test Method for Clay Lumps and Friable Particles in Aggregates

Doha Laboratory

1- Balance S/N: Q/BL/029 2- Container 3- Sieves 4- Oven S/N: 14E133

Sherin M-0144 Rahoof M-099

BS 812 - 112:1990 Testing aggregates. Method for determination of aggregate impact value (AIV)

Doha Laboratory

1- Impact test machine S/N: QIL/AGG/AIV/01 2- Sieves S/N: Q/SV/042, Q/SV/200, Q/SV/087 3- Balance S/N: Q/BL/029

Shibi M-065 Chinthaka M-198

ASTM C131/C 131M-14

Standard Test Method for Resistance to Degradation of Small-Size Coarse Aggregate by Abrasion and Impact in the Los Angeles Machine

Doha Laboratory

1- Los Angeles abrasion machine S/N: QIL/LOS/001 2- Sieves 3- Balance S/N: Q/BL/029 4- Charge


ASTM D75-14 Standard Practice for Sampling Aggregates

Doha Laboratory

1. Shovel 2. Bag

1. Naseer - M-255 2. Shibi Abdulsathar Habeebulla- M- 065

BS EN 1367-2:2009 Tests for thermal and weathering properties of aggregates. Magnesium sulfate test-Soundness test

Doha Laboratory

1. Balance Q-BL-029 2. Tray 3. Sieves 4. Oven Q-OV-011 5. Thermometer Q-TM- 180 6. Density Hydrometer QIL-MMS-01"

1. Shakul Ameeth - M-019 2. Rouf Vp - M- 099


CATEGORY STD. NO./

METHOD/ISSUE DATES


SECTION

LOCATION/ FACILITY


USED (NAME/ID NO.)

NAMES OF APPROVED


Aggregate BS EN 1097-2:2010 Tests for mechanical and physical properties of aggregates. Methods for the determination of resistance to fragmentation CL 5

Doha Laboratory

1. LAA machine QIL/STP/13 2. Sieves 3. Oven Q-QV-011 4. Balance Q-BL-029

1. Shibi Abdulsathar Habeebulla - M- 065 2. Arun Pandiya - M-182

ASTM D5821-13 Standard Test Method for Determining the Percentage of Fractured Particles in Coarse Aggregate

Doha Laboratory

1. Balance (Q-BL-029) 2. Sieves 3. Tray 4. Caliper (Q-VC-019)"

1. Shakul Ameeth - M-019 2. Athul Reddy - M-253

ASTM D546-10 Standard Test Method for Sieve Analysis of Mineral Filler for Bituminous Paving Mixtures

Doha laboratory

1. Sieves 2. Oven (Q-OV-011) 3. Balance (Q-BL-033)

1. Vishnu - M-274 2. Arun Pandiya - M-182

AASHTO T304-15 Standard Method of Test for Uncompacted Void Content of Fine Aggregate

Doha laboratory

1. Sieves 2. Oven (Q-OV-11) 3. Balance (Q-BL-33)

4. UVC Apparatus (Q- VOID-AGG-01)

1. Athul Reddy - M-253

2. Naseer - M-255

BS 812 - 103.1:1985

Testing aggregates. Method for determination of particle size distribution. Sieve tests- Clauses 7.2 & 7.3

Doha Laboratory

1- Sample divider Q/R/01 2- Oven 14E 133 3- Balance Q/BL/29 4- Test sieves 5- Mechanical shaker 6- Container

Rahoof-M-099 Shakul M-019

BS EN 932 - 1:1997

Tests for general properties of aggregates. Methods for sampling

Field Test 1- Shovel 2- Sample bags 3- Riffle box Q/R/01

Doss M-121 Rahoof M-099

BS 812-102:1989 Testing aggregates. Methods for sampling

Field Test 1- Scoop 2- Containers 3- Splitter Q/R/01

Doss M-121 Rahoof M-099

ASTM C117:2013 Standard Test Method for Materials Finer than 75-μm (No. 200) Sieve in Mineral Aggregates by Washing

Doha Laboratory

1- Balance Q/BL/29 2- Sieves 3- Container 4- Oven Q/OV/05

Doss M-121 Shakul M-019

BS 812 - 109:1990 Testing aggregates. Methods for determination of moisture content

Doha Laboratory

1- Balance 2- Container 3- Oven 4- Scoop 5- Thermometer

Shibi M-065 Doss M-121

BS 812 - 2:1995 Testing aggregates. Methods for determination of density- Clauses 5.3, 5.4 & 5.5

Doha Laboratory

1- Balance Q/BL/11 2- Oven Q/OV/005 3- Wire basket Q/WIR/SG/03 4- Air tight container 5- Sieves 6- Buoyancy table



CATEGORY STD. NO./

METHOD/ISSUE DATES


SECTION

LOCATION/ FACILITY


USED (NAME/ID NO.)

NAMES OF APPROVED


Aggregate BS EN 933 - 3:2012

Tests for geometrical properties of aggregates. Determination of particle shape. Flakiness index

Doha Laboratory

1- Test sieves 2- Corresponding bar sieves 3. Balance Q/BL/029


BS 812 - 105.1:1989

Testing aggregates. Methods for determination of particle shape. Flakiness index

Doha Laboratory

1- Riffle box Q/R/01,02 2- Balance Q/BL/029 3- Test sieve 4- Flakiness Gauge Q/FLK/01


BS 812 - 105.2:1990

Testing aggregates. Methods for determination of particle shape. Elongation index of coarse aggregate

Doha Laboratory

1- Riffle box Q/R/01 2- Balance Q/BL/029 3- Test sieve 4- Elongation gauge Q/ELG/01


BS EN 933-4:2008 Tests for geometrical properties of aggregates. Determination of particle shape. Shape index

Doha Laboratory

1-Proportional caliper -Q-S-VC-09 2- Balance - Q/BL/48 3- Sieves


ASTM D4791:2010 Flat particle, elongated particle, flat and elongated particle

Doha Laboratory

1- Riffle box Q/R/01 2- Balance Q/BL/029 3- Test sieve 4- Metal length gauge Q/ELG/ASTM/02


BS 812 - 121:1989 Testing aggregates. Method for determination of soundness

Doha Laboratory

1- Test sieves 2- Balance Q/BL/29 3- Container 4- Oven Q/OV/05 5- Density hydrometer 6- Desiccator 7- Thermometer Q/TM/180

Shibi M 065 Rahoof M-099

ASTM C88-13 Standard Test Method for Soundness of Aggregates by Use of Sodium Sulfate or Magnesium Sulfate

Doha Laboratory

1- Sieves 2- Container 3- Wire basket 4- Thermometer Q/TM/180 5- Balances Q/BL/029 6- Oven Q/OV/005 7- Hydrometer

Shibi M-065 Rahoof M-099

BS 812 - 111:1990 Testing aggregates. Methods for determination of ten per cent fines value (TFV)

Doha Laboratory

1- Steel cylinders 2- Tamping rod 3- Balance Q/BL/029 4- Test sieve 5- Compression testing machine Q/COM/01 6- Cylindrical metal measure QIL/AGG/TFV/01 7- Oven Q/OV/005 8- Metal tray 9- Drying cloth 10- Water tight container

Shakul M-019 Chinthaka M-198


CATEGORY STD. NO./

METHOD/ISSUE DATES


SECTION

LOCATION/ FACILITY


USED (NAME/ID NO.)

NAMES OF APPROVED


Aggregate ASTM C535:12 Standard Test Method for Resistance to Degradation of Large-Size Coarse Aggregate by Abrasion and Impact in the Los Angeles Machine

Doha Laboratory

1- Los Angeles abrasion machine QIL/LOS/01 2- Sieves 3- Balance Q/BL/029 4- Charge


BS EN 933 - 7:1988

Tests for geometrical properties of aggregates. Determination of shell content. Percentage of shells in coarse aggregates

Doha Laboratory

1- Balance Q/BC/029 2- Test sieve 3- Trays 4- Sieve shaker


BS 812 - 110:1990 Testing aggregates. Methods for determination of aggregate crushing value (ACV)

Doha Laboratory

1- Steel cylinder 2- Tamping rod 3- Balance Q/BL/029 4- Test sieves 5- Oven Q/OV/005 6- Compression machine 7- Cylindrical metal measure 8- Metal tray

Sherin M-0144 Chinthanka M-198

ASTM C123/C123M-14

Standard Test Method for Lightweight Particles in Aggregate

Doha Laboratory

1- Balance Q/BL/029 2- Container 3- Skimmer 4- Oven Q/OV/005 5- Sieves 6- Specific Gravity bottle


BS EN 1097-6:2013

Tests for mechanical and physical properties of aggregates. Determination of particle density and water absorption

Doha Laboratory

1- Oven Q/OV/05 2- Balance Q/BL/29 3- Water bath QIL/WB/01 4- Thermometer Q/TM/180 5- Sieves 6- Tray 7- Timer 8- Wire basket Q/WIR/SG/03 9- Water tank 10- Pycnometer Q/PYC/01 11- Metal mould 12- Tamper 13- Air dryer


Asphalt BSEN 12697-36:2003

Bituminous mixtures. Test methods for hot mix asphalt. Determination of the thickness of a bituminous pavement

Doha Laboratory

1- Vernier caliper S/N: C1201170552 2- Metal ruler or Tape S/N:Q/R/11

Samantha M-166 Nishanka M-222


CATEGORY STD. NO./

METHOD/ISSUE DATES


SECTION

LOCATION/ FACILITY


USED (NAME/ID NO.)

NAMES OF APPROVED


Asphalt ASTM D2726/D2726M-14

Standard Test Method for Bulk Specific Gravity and Density of Non-Absorptive Compacted Bituminous Mixtures

Doha Laboratory

1- Balance S/N: Q/BL/011 2- Water bath S/N: QIL/WB/01 3- Oven S/N: QIL-OV-009 4- Thermometer S/N: Q-TM-180

Samantha M-166 Ajith M-142

ASTM D70-09e1 Standard Test Method for Density of Semi- Solid Bituminous Materials (Pycnometer Method)

Doha Laboratory

1- Pycnometer S/N: QIL/PEN/02 2- Water bath S/N: QIL/WB/01 3- Thermometer S/N: Q-TM-180 4- Balance S/N: 711059003 5- Beaker

Mario-M-118 Ajith M-142

ASTM D2172/D2172M-11

Standard Test Methods for Quantitative Extraction of Bitumen From Bituminous Paving Mixtures

Doha Laboratory

1- Oven S/N: QIL-OV-009 2- Pan 3- Balances S/N: 711059003 4- Hotplate S/N: QIL/MUF/01 5- Graduated cylinders 6- Ignition dish 7- Desiccator 8- Extraction machine S/N: Q-ASPH-03


BS EN 12697-2:2015

Bituminous mixtures. Test methods. Determination of particle size distribution

Doha Laboratory

1- Sieves 2- Balance SN: 71105905 3- Drying Oven SN: QIL-OV-009

Jayantha M-113 Nishanka M-222

BS EN 1427:2015 Bitumen and bituminous binders. Determination of the softening point. Ring and Ball method

Doha Laboratory

1- Ring & ball apparatus/N:QIL/BIT/SOFT/01 2- Pouring plate 3- Ball centering guide 4- Thermometer S/N: Q/TM 180 5- Timing device /N: Q/STP/24 6- Hot plate S/N: Q/HTP/04

Mario-M-118 Ajith M-142


CATEGORY STD. NO./

METHOD/ISSUE DATES


SECTION

LOCATION/ FACILITY


USED (NAME/ID NO.)

NAMES OF APPROVED


Asphalt ASTM D 6927-15 Standard Test Method for Marshall Stability and Flow of Asphalt Mixtures

Doha Laboratory

1- Marshall testing apparatus S/N: Q/PVG/03 2- Flowmeter 3- Water bath S/N: QIL/WB/01 4- Oven S/N:Q-OV-014 5- Thermometer S/N: Q-TM-180 6- Steerer 7- Balance S/N: 711059003

Samantha M-166 Nishanka M-222 Ajith M-142

ASTM D6926-10 Standard Practice for Preparation of Bituminous Specimens Using Marshall Apparatus

Doha Laboratory

1- UoMld 2- Extractor 3- Marshall compactor Asset NO: Q/MCO/AUM/01 4- Containers 5- Oven; Asset No. Q/OV/09 6- Thermometer 7- Mixing tools 8- Balance; Asset No: Q/BL/11 9- Scoop

Samantha M 166 Nishanka M 222 Ajith M-142

ASTM E1703/E1703M-10

Standard Test Method for Measuring Rut- Depth of Pavement Surfaces Using a Straightedge

Field Test 1- Measuring device S/N: 2- Straight edge S/NTN 9037, Q/VC/13: TN6269

Saamantha M-166 Nishanka M-222 Ajith M-142

ASTM D2041/2041M-11

Standard Test Method for Theoretical Maximum Specific Gravity and Density of Bituminous Paving Mixtures

Doha Laboratory

1- Vacuum bowl 2- Flask 3- Balance S/N: Q/BL/011 4- Pump 5- Pressure monitor S/N: 5558 and VG-01 6- Thermometer S/N: Q/TM/180 7- Water bath S/N: QIL/WB/01 8- Oven 9- Agitator

Saamantha M-166 Nishanka M-222 Ajith M-142

BS EN 1426:2015 Bitumen and bituminous binders. Determination of needle penetration

Doha Laboratory

1- Penetrometer S/N: Q/ASP/PEN/02 2- Needle 3- Sample Container 4- Water bath S/N: QIL/WB/01 5- Transfer disk 6- Timing device 7- Thermometer S/N: Q/TM/180

Mario M-118 Ajith M-142


CATEGORY STD. NO./

METHOD/ISSUE DATES


SECTION

LOCATION/ FACILITY


USED (NAME/ID NO.)

NAMES OF APPROVED


Asphalt ASTM D6925-15 Standard Test Method for Preparation and Determination of the Relative Density of Asphalt Mix Specimens by Means of the Super pave Gyratory Compactor

Doha Laboratory

1- Super pave gyratory compactor: Asset No. Q/SGC/O1 2- Balance; Asset No. Q/BL/11 3- Thermometer 4- Specimen mold

Nishanka M-222 Nilantha M-199 Samantha M-166

AASHTO T312-2014

Preparation and determination of relative density of Asphalt mix specimen using Super pave gyratory compactor

Doha Laboratory

1- Super pave gyratory compactor: Asset No. Q/SGC/O1 2- Balance; Asset No.. Q/BL/11 3- Thermometer 4- Specimen mold

Nishanka M-222 Nilantha M-199 Samantha M-166

ASTM D2950/D2950M-14

Standard Test Method for Density of Bituminous Concrete in Place by Nuclear Methods

Field Test 1- Nuclear Gauge: Asset No. H-1739

Jamal M-010 Murthy M-12 Rajeev M-016

ASTM D6-11 Standard Test Method for Loss on Heating of Oil and Asphaltic Compounds

Doha Laboratory

1. Loss on heating oven - Q-ASP-LOH-01 2. Cup 3. Balance Q-BL-045 4. Oven (Q-OV-114)

1. Ajith - M-142 2. Samantha - M- 166

BS EN 12697-27:2001

Bituminous mixtures. Test methods for hot mix asphalt. Sampling

Field Test 1- Shovel 2- Thermometers QTM-111 3- Scoop

Jayantha M-113 Ajith M-142

BSEN 12697-28:2001

Bituminous mixtures. Test methods for hot mix asphalt. Preparation of samples for determining binder content, water content and grading

Doha Laboratory

1- Splitter Q/R/06 2- Tray 3- Balance Q/BL/11 4- Oven Q/OV/014 5- Metal tray


ASTM D3549:2011 Determination of Core Thickness

Doha Laboratory

1- Vernier caliper Q/VC/13 2- Tape


BSEN 12697-36:2003

Bituminous mixtures. Test methods for hot mix asphalt. Determination of the thickness of a bituminous pavement

Doha Laboratory

1- Vernier caliper 2- Metal ruler or Tape


BS EN 12697-6:2012

Bituminous mixtures. Test methods for hot mix asphalt. Determination of bulk density of bituminous specimens

Doha Laboratory

1- Balance Q/BL/011 2- Wire basket 3- Vernier Caliper Q/VC/13

Samantha M 166 Ajith M-142


CATEGORY STD. NO./

METHOD/ISSUE DATES


SECTION

LOCATION/ FACILITY


USED (NAME/ID NO.)

NAMES OF APPROVED


Asphalt ASTM D5/DM-13 Standard Test Method for Penetration of Bituminous Materials

Doha Laboratory

1- Penetration apparatus Q/ASP/PEN/02 2- Container 3- Water bath QIL/WB/01 4- Transfer dish 5- Timing device Q/STP/24

Mario M-118 Samantha M-166

BS EN 12697-29:2002

Bituminous mixtures. Test methods for hot mix asphalt. Determination of the dimensions of a bituminous specimen

Doha Laboratory

1- Caliper gauge Q/VC/13


ASTM D36/D36M-14E1

Standard Test Method for Softening Point of Bitumen (Ring-and-Ball Apparatus)

Doha Laboratory

1- Ring & ball apparatus QIL/BIT/SOFT/01 2- Pouring plate 3- Ball centering guide 4- Thermometer Q/TM/180 5- Steerer 6- Hot plate Q/HPT/04

Mario M-118 Ajith M-142

BSEN 12697-34:2012

Bituminous mixtures. Test methods for hot mix asphalt. Marshall test

Doha Laboratory

1- Compression testing machine Q/MAD/02 2- Water bath QIL/WB/01 3- Thermometer Q/TM/180 4- Oven Q/OV/014 5- Flow gauge Q/OG/33

Samantha M-166 Nishanka M-10222 Ajith M-142

BSEN 12697-30:2012

Bituminous mixtures. Test methods for hot mix asphalt. Specimen preparation by impact compactor

Doha Laboratory

1- Compactor Q/MCO/AUM/02 2- Moulds 3- Oven Q/OV/014 4- Thermometer Q/TM/111 5- Hot plate 6- Extruder


BSEN 12697-8:2012

Bituminous mixtures. Test methods for hot mix asphalt. Determination of void characteristics of bituminous specimens

Doha Laboratory

<Calculaton> Samantha M-166 Nishanka M-222

ASTM D2995-14 Standard Practice for Estimating Application Rate and Residual Application Rate of Bituminous Distributors

Doha Laboratory

1- Balance Q/BL/111 2- Geotextile pad



CATEGORY STD. NO./

METHOD/ISSUE DATES


SECTION

LOCATION/ FACILITY


USED (NAME/ID NO.)

NAMES OF APPROVED


Asphalt ASTM D2042-15 Standard Test Method for Solubility of Asphalt Materials in Trichloroethylene

Doha Laboratory

1- Bitumen crucible 2- Filter pad 3- Filter flask 4- Reagent 5- Vacuum pump

Saamantha M-166 Ajith M-142

ASTM D113-07 Standard Test Method for Ductility of Bituminous Materials

Doha Laboratory

1- Mould 2- Water bath QIL/WB/01 3- Ductility machine Q/ASP/DUC/01 4- Thermometer Q/TM/180 5- Oven 6- Trimming tools


ASTM D92-12b Standard Test Method for Flash and Fire Points by Cleveland Open Cup Tester

Doha Laboratory

1- Cleveland open cup QIL/FLASH/01 2- Test flame 3- Heater 4- Thermometer Q/TM/02


QCS:2014 Section 6- Part 5; Surface Irregularity (Evenness test)

Field Test 1- Taper rolls 2- Travelling beamTN-3624 3- Fiber tips-pencil


BSEN 12697-1:2012

Bituminous mixtures. Test methods for hot mix asphalt Soluble binder content

Doha Laboratory

1- Centrifuge extractor Q/ASPH/03 2- Oven Q/OV/009 3- Volumetric flask 4- Desiccator 5- Filter ring 6- Sieves

Saamantha M-166 Nishanka M-222

BS EN 12697-13:2000

Bituminous mixtures. Test methods for hot mix asphalt. Temperature measurement

Field Test 1- Thermometer Q/OV/111

Ajith M-142 Nishanka M-222

BSEN 12697-5:2009

Bituminous mixtures. Test methods for hot mix asphalt. Determination of the maximum density

Doha Laboratory

1- Ventilator cabin 2- Spatula 3- Balance Q/BL/011 4- Thermometer Q/TM/180 5- Water bath Q/WB/01 6- Pycnometer 7- Vacuum system Q/PG/25-Q/PG/26 8- Agitator 9- Vacuum desiccator Q/GMM/0111

Saamantha M-166 Nishanka M-222

BS EN 13036-7:2003

Road and airfield surface characteristics. Test methods. Irregularity measurement of pavement courses. The straightedge test

Field Test 1- Straight edge TN-6269 2- Wedge 3- Vernier caliper Q/VC/13



CATEGORY STD. NO./

METHOD/ISSUE DATES


SECTION

LOCATION/ FACILITY


USED (NAME/ID NO.)

NAMES OF APPROVED


Asphalt ASTM D6307-10 Standard Test Method for Asphalt Content of Hot-Mix Asphalt by Ignition Method

Doha Laboratory

1- Ignition Oven Q/IGN/01 2- Balance Q/BL/011 3- Splitter Q/R/06


ASTM D7113 Standard Test Method for Density of Bituminous Paving Mixtures in Place by the Electromagnetic Surface Contact Methods

Street 43 Lab Non- nuclear guage Rahoof Prajeesh

Soil ASTM D4402-15 Standard Test Method for Viscosity Determination of Asphalt at Elevated Temperatures Using a Rotational Viscometer

Doha Laboratory

1. Rotational viscometer - (QIL- RVIS-01) 2. Balance (Q/BL/001) 3. Stop Watch TN13400) 4. Drying Oven (Q-OV- 114)

1. Ajith - M-142 2. Mario - M-118 3. Samantha

ASTM D979-15 CL 6.3.3

Standard Practice for Sampling Bituminous Paving Mixtures

Doha Laboratory

1. Shovel 2. Tray 3. Bags 4. Thermometer (Q- TM-207)

1. Ajith - M-142 2. Mario - M-118

ASTM E303-13 Standard Test Method for Measuring Surface Frictional Properties Using the British Pendulum Tester

Doha Laboratory

1. Skid resistance apparatus Model A113 (SN A113-HE-0037)

1. Shibi Abdulsathar Habeebulla - M- 065 2. Nihal - M-023

ASTM D5444-15 Standard Test Method for Mechanical Size Analysis of Extracted Aggregate

Doha Laboratory

1. Sieves 2. Balance (Q-BL-011) 3. Oven (Q-OV-009) 4. Container

1. Jayantha - M- 113 2. Nishanka - M- 222

ASTM D1557:2012 e1

Determination of Dry density /Moisture content/Correction of unit weight

Doha Laboratory

1- Moulds 2- Automatic compactor Q/MDD/AUM/01 3- Balance Q/BL/48 4- Oven Q/OV/11 5- Sieves 6- Scoop 7- Straight edge

Safihan M-146 Rahoof M-099

ASTM D4318:2010 Liquid Limit and plasticity index

Doha Laboratory

1- Liquid limit device QIL/CSG/01 2- Flat grooving tools 3- Gauge 4- Container 5- Mixing & storage container 6- Glass plate 7- Spatula 8- Oven Q/OV/005

Doss M-121 Chinthaka M-198


CATEGORY STD. NO./

METHOD/ISSUE DATES


SECTION

LOCATION/ FACILITY


USED (NAME/ID NO.)

NAMES OF APPROVED


Soil ASTM D6938:2010 In-situ Density Test (Nuclear Method)

Field Test 1-Nuclear machine Q/NUCR/01 2- Survey meter 3- Drive pin guide plate 4- Opener 5- Film badge 6- Safety barricade cover 7- Pouring cylinder

Jamal Yogimadathil M-010 Rajeev M-016

ASTM D1556:2015 Field Density (Sand Replacement)

Field Test 1-Sand cone density apparatus Q/SAND/ASTM/01 2- Base plate 3- Balance Q/BL/37 4- Calibrating containers 5- Oven Q/OV/005 6- Speedy moisture tester Q/MOI/03

Rajeev Manoj M-158 Tobi M1144

ASTM D2419-14 Standard Test Method for Sand Equivalent Value of Soils and Fine Aggregate

Doha Laboratory

1- Graduated Cylinders 2- Measuring Tin 3- Sieves 4- Funnel 5- Bottle 6- Shaker S/N: Q/SET/1 7- Stop Watch S/N: Q/STP/11, Q/STP/13, Q/STP/27 8- Oven S/N: Q/OV//005 9- Balance S/N: Q/BN/029

Safihan M-146 Abdulla M-233

BS 1377-1:1990 Soil Sampling Field Test 1- Shovel 2- Splitter Q/R/O1


BS 1377-2:1990 Methods of test for soils for civil engineering purposes. Classification tests Clause 5: plasticity index CL 4 Liquid Limit

Doha Laboratory

1- Balance S/N: 7111059003 2- Sieves 3- Oven S/N: Q-OV-005 4- Containers 5- Scoop 6- Riffle box 7- Spatulas 8- Glass plate 9- Wash bottle 10- Straight rod 11- Cone penetrometer S/N:QIL/PEN/02 12- Casacarande apparatus S/N: Q/VC/007 13- Desiccator 14- Linear shrinkage UoMld 15- Thermometer S/N: S/N: Q/TM/180

Doss M-121 Chinthaka M-198


CATEGORY STD. NO./

METHOD/ISSUE DATES


SECTION

LOCATION/ FACILITY


USED (NAME/ID NO.)

NAMES OF APPROVED


Soil BS 1377-2 Section 9:1990

Soil Sieve Analysis/Mat finer than 75 micron

Doha Laboratory

1-Balance Q/BL/029 2- Sieves 3- Oven Q/OV/11 4- Containers 5- Scoop

Arun Pandiyan M-182 Shibi M-065

BS 1377-9:1990 Methods for test for soils for civil engineering purposes. In-situ tests – Clause 2.5 In-situ Density Test(Nuclear Method)

Field Test 1- Nuclear machine S/N: 8550 2 -Survey meter 3- Drive pin guide plate 4- Opener 5- Film badge 6- Safety barricade cover 7- Pouring cylinder

Jamal Yogimadathil M-010 Rajeev M-016

BS 1377-9:1990 Methods for test for soils for civil engineering purposes. Clauses 2.1 & 2,2 - In-situ tests Field Density (Sand Replacement)

Field Test 1- Sand cone density apparatus S/N: Q/SAND/POUR/200/7 2- Base plate 3- Balance S/N:Q-BL-037 4- Calibrating containers 5- Oven S/N: Q-OV-005 6- Speedy moisture tester

Rajeev Manoj M-158 Tobi M-144

BS EN 933-8:2015 Sand Equivalent Value of soil and fine aggregates

Doha Laboratory

1- Graduated cylinders 2- Test plunger assembly 3- Sieves 4- 500 mm Rule 5- Shaker Q/SET/01 6- Stop watch Q/STP/13,27,11 7- Balance Q/BL/29


BS 1377-9:1990 Non Repetitive Plate load test

Field Test 1- Loading device 2- Hydraulic jack Q/PG/17 3- Load cell 4- Bearing plate 5- Deflection beam 6- Data acquisition system

Mr. Fadi G-04 Mr. Nishfar G-059

ASTM C702-11 Standard Practice for Reducing Samples of Aggregate to Testing Size

Doha Laboratory

1. Tray 2. Riffle box 3. Shovel 4. Scoop 5. Sieves

1. Shibi Abdulsathar Habeebulla - M-065 2. Naseer - M-255

ASTM D2216-10 Standard Test Methods for Laboratory Determination of Water (Moisture) Content of Soil and Rock by Mass

Doha Laboratory

1. Oven (Q-OV-11) 2. Balance (Q-BL-029) 3. Container 4. Desicator

1. Shakul Ameeth - M- 019 2. Ansari - M-260


CATEGORY STD. NO./

METHOD/ISSUE DATES


SECTION

LOCATION/ FACILITY


USED (NAME/ID NO.)

NAMES OF APPROVED


Soil ASTM D6913-09 Particle Size Distribution Doha Laboratory

1. Sieves 2. Balance (Q-BL-029) 3. Oven (Q-OV-011) 4.Tray

1. Shibi Abdulsathar Habeebulla - M-065 2. Rouf Vp - M-099

ASTM D1140-14 Standard Test Methods for Determining the Amount of Material Finer than 75-& mu;m (No. 200) Sieve in Soils by Washing

Doha Laboratory

1. 75um Sieves 2. 425 um Guard Sieve 3. Balance Q-BL-029 4. Oven Q-OV-011 5.Tray

1. Shibi Abdulsathar Habeebulla - M-065 2. Rouf Vp - M-099

ASTM D4718-15 Standard Practice for Correction of Unit Weight and Water Content for Soils Containing Oversize Particles

Doha Laboratory

1. Sieves 2. Balance Q-BL-029 3. Oven Q-OV-011 4.Tray

1. Athul Reddy - M- 253 2. Shakul Ameeth - M- 019

ASTM D4944-11 Standard Test Method for Field Determination of Water (Moisture) Content of Soil by the Calcium Carbide Gas Pressure Tester

Doha Laboratory

1. Speedy moisture apparatus (Q-MOI-05) 2. Balance (Q-BL-024) 3. Stop Watch Q-STP- 27

1. Ansari - M-260 2. Arun Pandia - M- 182

ASTM D4429-09 Standard Test Method for CBR (California Bearing Ratio) of Soils in Place

Field Test 1. Jack 2. Proving Ring (Q- PVG-06) 3. Plunger 4. Dial gauge (Q-DG- 92) 5. Balance (Q-BL-29) 6. Oven (Q-OV-11)

1. Sameer - G-043 2. Nishfar - G-059

BS 1924-2:1990 Method of Test for Cement Stabilized Materials CL 1.3.3, 1.3.7, 1.4.4, 1.4.5, 1.4.6, 2.1.4, 3.1 & 4.2

Doha Laboratory

1. Oven (Q-OV-11) 2. Balance (Q-BL-29) 3. Container 4. Scoop 5. Palette Knife 6. Cone penetrometer (QIL-PEN-02) 7. MDD Molds 8. Rammer (Q-RAM- 11) CBR/K)9. CBR Molds (BS/ 10. CBR Machine (Q- CBR-02) 11. Compression machine (Q-COM-06) 12. Nuclear gauge (H- 8449)

1. Shakul Ameeth - M-019 2. Rouf Vp - M-099


CATEGORY STD. NO./

METHOD/ISSUE DATES


SECTION

LOCATION/ FACILITY


USED (NAME/ID NO.)

NAMES OF APPROVED


Soil BS 1377:1990 Methods of tests for soils for civil engineering purposes: Compaction related tests- Section 3 Determination of Dry Density/Moisture Content/Correction of unit weight

Doha Laboratory

1- Test sieves 2- Balance Q/BL/48 3- Mould Q/M/BS/02 4- Rammer 2.5 kg, 4.5 kg 5- Containers 6- Trays 7- Straight edge 8- Spatula 9- Oven Q/OV/11 10- Desiccator

Safihan M-146 Rahoof M-099

BS 1377-4:1990 Methods of test for soils for civil engineering purposes. Compaction-related tests Section 7: California Bearing Ratio test

Doha Laboratory/Field

1- Soaking tank 2- CBR Machine QIL/CBR/01 3- Moulds BS/CBR/A8 4- Spacer disk 5- Sieves 6- Surcharge weight 7- Swell measurement device 8- Rammer 9- Oven Q/OV/005 10- Balance Q/BL/48


BS 1377-2:1990 Methods for test for soils for civil engineering purposes. In-situ tests – Clause 3 Moisture Content

Doha Laboratory

1- Drying oven S/L: Q-OV-005 2- Balance S/L: Q-BL-029 3- Container 4- Desiccator

Arun Pandiyan M-181 Shibi M-065

ASTM D1883-14 Standard Test Method for California Bearing Ratio (CBR) of Laboratory-Compacted Soils

Doha Laboratory

1- Soaking tank 2- CBR Machine QIL/CBR/01 3- Moulds Q/ASTM/CBR/01,02,03 4- Spacer disk 5- Sieves 6- Surcharge weight 7- Swell measurement device 8- Rammer 9- Oven Q/OV/005 10- Balance Q/BL/48 11- Dial gauge


ASTM D1196-12 Standard Test Method for Non-repetitive Static Plate Load Tests of Soils and Flexible Pavement Components, for Use in Evaluation and Design of Airport and Highway Pavements

Field Test 1- Loading device 2-Hydraulic jack Q/PG/17 3- Load cell 4- Bearing plate 5- Deflection beam 6- Data acquisition system



CATEGORY STD. NO./

METHOD/ISSUE DATES


SECTION

LOCATION/ FACILITY


USED (NAME/ID NO.)

NAMES OF APPROVED


Soil BS 1377-9:1990 Methods for test for soils for civil engineering purposes. In-situ tests : Clause 4.1 Plate load test

Field Test 1- Loading device 2-Hydraulic jack Q/PG/17 3- Load cell 4- Bearing plate 5- Deflection beam 6- Data acquisition system


BS 1377-2 Section 8:1990

Methods of test for soils for civil engineering purposes. Classification tests- Section 8 Particle density Test

Doha Laboratory

1- Electronic balance Q/BL/29 2- Sieves 3- Sample Splitters Q/R/01 4- Drying Oven Q/OV/05 5- Jar, Thermometer & Stopwatch Q/STP/11


BS 1377-9:1990 Methods for test for soils for civil engineering purposes. In-situ tests – Clause 4.3 Field CBR

Field Test 1-.Reaction load like truck 2- Diameter loading plunger 3- Extension rods 4- Jacks , proving ring, dial gauge Q/DG/050 5- Datum frame Q/PVG/4

Mr. Samir G-043 Mr. Nishfar G-059

Concrete BS EN 12390-3:2009

Testing hardened concrete. Compressive strength of test specimens

Doha Laboratory

1- Compression machine S/N: Q/COM/01

Danushka M-102 Naveen M-038

BS EN 12390-1:2012

Shape and dimensions for specimens

Doha Laboratory

1- Caliper 2- Straight edge 3- Feeler gauge 4- Try square


BS EN 12390-7:2009

Testing hardened concrete. Density of hardened concrete

Doha Laboratory

1- Weighing scale S/N: 8334320013


ASTM C138/C138M-14

Standard Test Method for Density (Unit Weight), Yield, and Air Content (Gravimetric) of Concrete

Doha Laboratory

1- Density pot S/N: 4130882746 2- Tamping rod S/N: QIL/CROD/04 3- Scoop 4- Glass plate 5- Balance S/N: QIL/BL/029

Lahiru M-131 Diluksha M-109

BS 1881-122:2011 Determination of water Absorption in Hardened concrete

Doha Laboratory

1- Drying oven S/N: QIL/OV/017 2- Curing tank 3- Balance S/N: Q-BL-029 4- Desiccator

Chandana M-036 Nihal M-23


CATEGORY STD. NO./

METHOD/ISSUE DATES


SECTION

LOCATION/ FACILITY


USED (NAME/ID NO.)

NAMES OF APPROVED


Concrete BS 6717-1:2001 Compressive Strength of paving blocks

Doha Laboratory

1- Compression machine S/N: Q/COM/01 2- Vernier caliper S/N: QIL/VC/010 3- Steel Ruler

Nihal M-023 Isuru M-117

BS EN 1338:2003 Concrete paving blocks. Requirements and test methods

Doha Laboratory

1- Compression machine S/N: Q/COM/01 2- Tensile Frame 3- Ruler


ASTM C231/C231M-14

Standard Test Method for Air Content of Freshly Mixed Concrete by the Pressure Method

Field Test/Lab

1- Air meter S/N: 4130882746 2- Spray tube 3- Trowel 4- Mallet 5- Tamping rod S7N: QIL/CROD/04 6- strike off plate

Naveen M-038 Chandana H. M-035

ASTM C1202-12 Standard Test Method for Electrical Indication of Concrete's Ability to Resist Chloride Ion Penetration

Doha Laboratory

1- RCP apparatus S/N: QIL/RCP/01 2- Vacuum desiccator 3- Vacuum pump S/N: Q-VAC-02

Nihal M-023 Chandana M-036

BS EN 12390-8:2009

Testing hardened concrete. Depth of penetration of water under pressure

Doha Laboratory

1- Water penetration apparatus DE-PI-0015, Q/VC/1

Chandana M-036 sriyantha M-210

BS EN 12504-4: 2004

Testing concrete. Part 4: Determination of ultrasonic pulse velocity

Field Test 1-.Ultrasonic Pulse Velocity Proceq -HW 83; SN>327400100

Ajay M-133 Lahiro M-131 Ropero M-027

BS EN 12350-1:2009

Testing fresh concrete. Sampling

Field Test 1- Sampling tray 2- Scoop 3- Showel

Diluksha M-109 Ruwantha M-125

BS EN 12390-2:2009

Testing fresh concrete. Slump-test

Doha Laboratory

1- Cube & cylinder moulds 2- Tamping bar QIL/CBAR/04 3- Trowel 4- Scoop 5- Rubber mallet Q/RHMR/01 6- Curing tanks


ASTM C31/C31M-15

Standard Practice for Making and Curing Concrete Test Specimens in the Field

Doha Laboratory

1- Cube & cylinder moulds 2- Tamping bar QIL/CROD/01 3- Trowel 4- Scoop 5- Rubber mallet Q/RHMR/01 6- Curing tanks



CATEGORY STD. NO./

METHOD/ISSUE DATES


SECTION

LOCATION/ FACILITY


USED (NAME/ID NO.)

NAMES OF APPROVED


Concrete BS EN 772-1:2015 Methods of test for masonry units. Determination of compressive strength

Doha Laboratory

1- Compression machine Q/COM/01 2- Balance Q/BL/043 3- Ruler QIL/R/08


ASTM C39:2015a Standard Test Method for Compressive Strength of Cylindrical Concrete Specimens

Doha Laboratory

1- Coring machine 2- Trimming machine 3- Compression machine Q/COM/01 4- Vernier caliper QIL/VC/010 5- Balance Q/BL/043


BS EN 12504-1:2009

Testing concrete in structures. Cored specimens. Taking, examining and testing in compression

Doha Laboratory

1- Coring Machine 2- Compression machine - Q/COM/01 3- Weighing balance - Q/BL/043

Chandana M-036 Nihal M-023 Dinesh M-48 Chandana M-035

ASTM C42/C42M-13

Standard Test Method for Obtaining and Testing Drilled Cores and Sawed Beams of Concrete

Doha Laboratory

1- Compression Machine -Q/COM/07 2- Flexural frame - Q/FLEX/01 3- Weighing scale - Q/BL/043


ASTM C78-15a Standard Test Method for Flexural Strength of Concrete (Using Simple Beam with Third- Point Loading)

Doha Laboratory

1- Flexural machine - Q/FLEX/01 2- Ruler QIL/R/08

Chandana M-036 Samantha M-130

ASTM C1064-12 Standard Test Method for Temperature of Freshly Mixed Hydraulic-Cement Concrete

Field Test 1- Thermometer Q/TM/106

Chandana M-036 Samantha M-130

BSEN 12350-2:2009

Testing fresh concrete. Slump-test

Field Test 1- Slump cone QIL/SLU/04 2- Scoop 3- Slump rod QIL/CROD/04 4- Base plate


BS 6717:2001 Precast, unreinforced concrete paving blocks. Requirements and test methods

Doha Laboratory

1- Compression Machine 2- Vernier Caliper 3- Ruler


BS 1881-208:1996 Testing concrete. Recommendations for the determination of the initial surface absorption of concrete

Doha Laboratory

1- ISAT apparatus QIL/ISAT/01


ASTM C140-15 Standard Test Methods for Sampling and Testing Concrete Masonry Units and Related Units

Field Test 1- Steel Scale QIL/R/08 2- Compression M achine Q/COM/01 3- Balance Q/BL/043 4- Flexural Machine

Chandana M-036 Nihal M-023 chandana H. M-035


CATEGORY STD. NO./

METHOD/ISSUE DATES


SECTION

LOCATION/ FACILITY


USED (NAME/ID NO.)

NAMES OF APPROVED


Concrete ASTM C143/C143M

Standard Test Method for Slump of Hydraulic-Cement Concrete

Field Test/Lab

1- Slump cone QIL/SLU/03 2- Slump rod QIL/CROD/03 3- Base Plate

Danushka M-102 lahiru M-131

ASTM C172-14a Standard Practice for Sampling Freshly Mixed Concrete

Field Test/Lab

1- Base Plate 2- Sieves 3- Shovels 4- Hand scoops 5- Trowels


ASTM C 183-15 Standard Practice for Sampling and the Amount of Testing of Hydraulic Cement

Field Test 1-Tube sampler Nihal M-023 Diluksha M-109

ASTM C187-11 e1 Standard Test Method for Amount of Water Required for Normal Consistency of Hydraulic Cement Paste

Doha Laboratory

1- Weights and Weighing Devices Q/BL/043 2- Glass Graduates 3- Vicat Apparatus


ASTM C191-13 Standard Test Methods for Time of Setting of Hydraulic Cement by Vicat Needle

Doha Laboratory

1- Weights and Weighing Devices Q/BL/043 2- Glass Graduates 3- Vicat Apparatus


ASTM C349-14 Standard Test Method for Compressive Strength of Hydraulic-Cement Mortars (Using Portions of Prisms Broken in Flexure)

Doha Laboratory

1- Compression M achine Q/COM/01 2- Aligning Device


ASTM C642-13 Standard Test Method for Density, Absorption, and Voids in Hardened Concrete

Doha Laboratory

1- Drying Oven QIL/OV/017 2- Balance Q/BL/028 3- Container 4- Hot Plate


ASTM C805-13a Standard Test Method for Rebound Number of Hardened Concrete

Field Test 1- Rebound Hammer Q/HAM/02

Isuru M-117 Chandana H. M-035

ASTM C900-15 Standard Test Method for Pullout Strength of Hardened Concrete

Field Test 1- Hi Force Hydraulic Jack with pump & gauge

Arunnath M-157 Ajay M-133

ASTM C989-14 Standard Specification for Slag Cement for Use in Concrete and Mortars

Doha Laboratory

1- Flow table 2- Balance Q/BL/043 3- Ruler Q/R/08 4- compression machine Q/COM/01 5- Containers 6- Curing tank


ASTM C1012/C1012M-15

Standard Test Method for Length Change of Hydraulic-Cement Mortars Exposed to a Sulfate Solution

Doha Laboratory

1- Mixer QIL/GMIX/01 2- Cube molds 3- Bar molds 4- Comparator 5- Containers 6- Curing tank



CATEGORY STD. NO./

METHOD/ISSUE DATES


SECTION

LOCATION/ FACILITY


USED (NAME/ID NO.)

NAMES OF APPROVED


Concrete ASTM C1240-15 Standard Specification for Silica Fume Used in Cementitious Mixtures

Doha Laboratory

1- Flow table 2- Balance Q/BL/043 3- Ruler Q/R/08 4- compression machine Q/COM/01 5- Containers


ASTM C1611-14 Standard Test Method for Slump Flow of Self-Consolidating Concrete

Doha Laboratory

1- Slump Cone QIL/SLU/04 2- Base plate 3- Strike off bar 4- Ruler Q/R/08


BS EN 196-1:2005 Methods of testing cement. Determination of strength

Doha Laboratory

1- Mixer QIL/GMIX/01 2- Moulds 3- Jolting apparatus 4- Jig for flexural and compressive strength

Nihal M-023 Diluksha M-109

BS EN 196-6:2010 Methods of testing cement. Determination of fineness

Doha Laboratory

1- Blaine permeability apparatus QIL/BLN/01 2- Balance Q/BL/028 3- Stop watch Q/STP/017

Nihal M-023 SrIyantha M-210

BS EN 196-3: 2005 + A1:2008

Methods of testing cement. Determination of setting times and soundness

Doha Laboratory

1- Vicat apparatus Nihal M-023 Chandana M-036

BS EN 196-7:2007 Methods of testing cement. Methods of taking and preparing samples of cement

Field Test 1- Tube sampler Nihal M-023 Diluksha M-109

BS EN 450-1:2012 Fly ash for concrete. Definition, specifications and conformity criteria

Doha Laboratory

1- Compression machine Q/COM/01 2- Le Chatlier apparatus QIL/SNA/01 3- Water bath 4- Caliper QIL/VC/10

Nihal M-023 SrIyantha M-210

BS EN 771-1:2011 Specification for masonry units. Clay masonry units(Compressive strength and water absorption)

Doha Laboratory

1- Compression machine Q/COM/01 2- Ruler Q/R/08 3- Weighing scale Q/BL/043 4- Drying Oven QIL/OV/017

Naveen M-038 Chandana M-036

BS EN 771-3:2011 Specification for masonry units. Aggregate concrete masonry units (dense and lightweight aggregates)

Doha Laboratory

1- Compression machine Q/COM/01 2- Ruler Q/R/08 3- Weighing scale Q/BL/043 4- Drying Oven QIL/OV/017

Naveen M-038 Chandana M-036

BS EN 12350-5:2009

Testing fresh concrete. Flow table test

Doha Laboratory

1- Flow table 2- Flow cone 3- Compacting bar 4- Ruler Q/R/08 5- Scoop

Samantha M-130 Ruwantha M-125


CATEGORY STD. NO./

METHOD/ISSUE DATES


SECTION

LOCATION/ FACILITY


USED (NAME/ID NO.)

NAMES OF APPROVED


Concrete BS EN 12504-2:2012

Testing concrete in structures. Non- destructive testing. Determination of rebound number

Doha Laboratory

1- Rebound hammer Q/HAM/02 2- Test anvil

Chandana H. M-036 Danushka M-102

BS EN 13791:2007

Assessment of in-situ compressive strength in structure and precast concrete

Doha Laboratory

Not a test only assessment


BS 6073-1:1981 Precast concrete masonry units. Specification for precast concrete masonry units

Doha Laboratory

1- Vernier Caliper QIL/VC/010 2- balance Q/BL/043 3- Compression machine Q/COM/01


BS EN 1340:2003 Concrete kerb units. Requirements and test methods: Appendix C Dimension: Appendix E Water absorption and Appendix F Transverse strength of kerbs

Doha Laboratory

1- Drying Oven 2- Straight edge 3- Feller gauge 4- Flexural frame

Chandana M-036 Sriyantha M-210

BS EN 1339:2003 Concrete paving flags. Requirements and test methods - Appendix E: Transverse strength Appendix F:Water absorption

Doha Laboratory

1- Flexural machine 2- Ruler Q/R/08 3- Oven QIL/OV/017 4- Balance Q/BL/043 5- Curing tank


BS 6073-2:2008 Precast concrete masonry units. Guide for specifying precast concrete masonry units

Doha Laboratory

Specification for requirements only


Steel ASTM A370-15 Standard Test Methods and Definitions for Mechanical Testing of Steel Products

Doha Laboratory

1- UTM -Q/MET/01 2- Balance 3- Measuring scale 4- Vernier caliper

Arun M-147 Ajay M-134

BS 4449:2005 +A2:2009

Testing of Carbon steel bars for tensile and Rebend test

Doha Laboratory

1- UTM -Q/MET/01 2- Balance 3- Measuring scale 4- Vernier caliper 5- Bending pins


ASTM A615:2014 Steel for the reinforcement of concrete. Weldable reinforcing steel. Bar, coil and decoiled product. Specification

Doha Laboratory

1- UTM-Q/MET/01 2- Balance 3- Measuring scale 4- Vernier caliper 5- Bending pins


NDT ASTM G62-14 Standard Test Methods for Holiday Detection in Pipeline Coatings

Field Test 1- Elcometer Ajay M-133 Shibi M-065


CATEGORY STD. NO./

METHOD/ISSUE DATES


SECTION

LOCATION/ FACILITY


USED (NAME/ID NO.)

NAMES OF APPROVED


NDT ASTM D4541-09 e1

Standard Test Method for Pull-Off Strength of Coatings Using Portable Adhesion Testers

Field Test 1- Elcometer 106 Adhesion Tester

Jerry Seludo C-07 Marlon Camero C-03 Jinu Khan C-011 Shajahan Kasim C-13

ASTM D4945-12 Standard Test Method for High-Strain Dynamic Testing of Deep Foundations

Field Test 1- Pile driving Analyzer Michael G-05 Manuel M-008

ASTM D5882-13 Standard Test Method for Low Strain Impact Integrity Testing of Deep Foundations

Field Test 1- Pile integrity tester Michael G-05 Manuel M-008

ASTM D6760-14 Standard Test Method for Integrity Testing of Concrete Deep Foundations by Ultrasonic Cross hole Testing

Field Test 1- Cross hole analyzer Michael G-05 Manuel M-008

ASTM D6167-11 Standard Guide for Conducting Borehole Geophysical Logging: Mechanical Caliper

Field Test 1- Three arm caliper by Robertson geologging

Michael G-05 Manuel M-008

BS EN 124:1994 Gully tops and manhole tops for vehicular and pedestrian areas 0 Design requirements, type testing, marking, quality control

Lab Test 1- Manhole Cover Testing Machine (Ele); SN; AA80613 2- Caliper; Asset No. Q/VC/13

Ajay M-133 Arun Nath M-147

BS EN 12504-4:2004

Testing concrete. Determination of ultrasonic pulse velocity

Field Test 1- Proceq PL-200 Ajay M-133 Lahiro M-131 Ropero M-027

ASTM D6132-13 Standard Test Method for Nondestructive Measurement of Dry Film Thickness of Applied Organic Coatings Using an Ultrasonic Coating Thickness Gage

Field Test 1- Positector 200 Advance


ASME Section V:2007

Magnetic particle inspection

Doha Laboratory

1- Pie gauge 2- Electromagnet 3- MPI Ink 4- Permanent Magnet

Arun Nath M-147 Ajay M-133

ASME Section V:2007

Dye penetration test Doha Laboratory

1- Penetrant 2- Developer 3- Cleaner


ASTM E18 Standard Test Methods for Rockwell Hardness of Metallic Materials

Doha Laboratory

1- Hardness test machine -Equotip -3 2- Probe with cable 3- Block


ASTM E10:2003 Brinell hardness test Doha Laboratory

1- Hardness test machine -Equotip -3 2- Probe with cable 3- Block



CATEGORY STD. NO./

METHOD/ISSUE DATES


SECTION

LOCATION/ FACILITY


USED (NAME/ID NO.)

NAMES OF APPROVED


NDT ASME Section V:2007

Ultrasonic test -Welding Doha Laboratory

1- Ultrasonic flow detector 2- Calibration block 3- Probes


Microscope manual Crack width measurement using microscope

Field Test 1. Microscope (QIL- CRK-02)

1. Ajay Mohandas - M-133 2. Vineesh - M-243

BS 1881 Part 204:1988

Testing concrete. Recommendations on the use of electromagnetic covermeters

Doha l Laboratory

1. Cover meter (V/02) 1. Marlon Camero- C- 03 2. Shajahan Kasim - C-13

NT BUILD 492:1999

Chloride migration test Doha Laboratory

1. DC Power supply (QIL/CMT/04-04, /05, /06, /07, /08, /09) 2. Caliper (1483) 3. Multimeter (QIL- DMM-01) 4. Thermometer (QIL- TM-101)

1. Marlon Camero- C- 03 2. Shajahan Kasim - C-13

Geotechnical ASTM D7012-14 Standard Test Methods for Compressive Strength and Elastic Moduli of Intact Rock Core Specimens under Varying States of Stress and Temperature

Doha Laboratory

1- Compression machine 2- Oven

Mr. Sukhvinder G-081 Nishfar G-059

BS 5930:1999 + A2:2010

(Code of Practice for Site Investigation)Packer Test CL 25

Field Test 1- Packer Equipment (Single or Double) 2- Pressure pump with pressure gauge 3- Stop watch 4- Drilling Equipment 5- Dip meter 6- Measuring Tape

Mr. Ubaid G-026 Mr. Sameer G-043

BS 5930:1999+ A2:2010

Code of Practice for Site Investigation (Geotech Sampling & Description)

Field Test 1- Drilling Rig Mr. Fadi G-04 Mr. Ubaid G-026

ASTM D5731:2008 Determination of point load strength index of rock

Doha Laboratory

1- Point load apparatus 2- Digital Pressure Gauge (Model LEO 2 Mono200) 3- Stop watch


ASTM G57:2012 Standard Test Method for Field Measurement of Soil Resistivity Using the Wenner Four-Electrode Method

Field Test 1- Digital Earth Tester (DET5/4D) 2- Electrodes 3- Measuring Tape

Mr. Sukhvinder G-081 Mr.Anujan G-064


CATEGORY STD. NO./

METHOD/ISSUE DATES


SECTION

LOCATION/ FACILITY


USED (NAME/ID NO.)

NAMES OF APPROVED


Geotechnical ASTM D4543-08 Standard Practices for Preparing Rock Core as Cylindrical Test Specimens and Verifying Conformance to Dimensional and Shape Tolerances

Doha Laboratory

1- V blocks 2- Displacement Gage assembly 3- Dial or electronic displacement gage 4- Feeler gage 5- Surface grinder

Mr. Faddi G-04 Mr. Sukhvinder G-081

BS 5930:1999 + A2:2010

(Code of Practice for Site Investigation) Clause 27: Pumping Test

Field Test 1- Drilling Equipment 2- Stop watch 3- Dip meter 4- Measuring tape

Mr. UbaidG-026 Mr. Sameer G-043

BS 5930:1999 + A2:2010

(Code of Practice for Site Investigation) Permeability Test Clause 25: Constant Head+ Falling Head

Field Test 1- Drilling Equipment 2- Stop watch 3- Balance 4- Steel ruler 5- Caliper

Mr. Ubaid G-026 Mr. Sameer G-043 Mr. Anujan G-064

BS 1377-5:1990 Methods of test for soils for civil engineering purposes. Compressibility, permeability and durability tests - Clause 5: Determination of permeability by the constant-head method

Doha Laboratory

1- Permeameter 2- Stop watch 3- Dip meter 4- Measuring tape 5- Flow meter

Doss M-121 Shibi M-065

ASTM D5607-08 Standard Test Method for Performing Laboratory Direct Shear Strength Tests of Rock Specimens Under Constant Normal Force

Doha Laboratory

1- Shear box apparatus 2- Outer Container 3- Two porous plates 4- Two perforated spacer plates 5- Loading cap 6- Load Cell/ Force measuring device\ 7- Dial gauges/ Displacement sensors 8- Vernier 9- Stop watch 10- Balance

Mr. Doss M-121 Mr. Shakul M-019

BS 1377-7:1990 Methods of test for soils for civil engineering purposes. Shear strength tests (total stress) -Clause 4: Determination of shear strength by direct shear (small shear box apparatus)

Doha Laboratory

1- Shear box apparatus 2- Outer Container 3- Two porous plates 4- Two perforated spacer plates 5- Loading cap 6- Load Cell/ Force measuring device 7- Dial gauges/ Displacement sensors 8- Vernier 9- Stop watch 10- Balance

Mr. Doss M-121 Mr. Shakul M-019

BS 5930:1999+A2:2010

Section 4 Cl 25.7:Pressuremeter Test

Field Test 1- Elastmeter 2.0 2- Probe with calibration ring 3- Packer rubber tube



CATEGORY STD. NO./

METHOD/ISSUE DATES


SECTION

LOCATION/ FACILITY


USED (NAME/ID NO.)

NAMES OF APPROVED


Geotechnical BS 1377-9:1990 Methods for test for soils for civil engineering purposes. In-situ tests – Clause 3.3 Standard penetration test (SPT)

Field Test 1- SPT Hammer 2- SPT Sampler 3- Rod 4- Measuring tape

Mr. Ubaid G-026 Mr. Anujan G-064

ASTM D5334-14 Standard Test Method for Determination of Thermal Conductivity of Soil and Soft Rock by Thermal Needle Probe Procedure

Doha Laboratory

1- kd2 Thermal properties analyzer thermal grease


Chemical SMEWW 4500 H+ B

pH in water Doha Laboratory

1- pH Meter 2- Glasswares


SMEWW 4500-Cl G

Chlorine Residual Doha Laboratory

1- Spectrophotometer 2- Glasswares


SMEWW 4500-SO42 C

Sulphate Doha Laboratory

1- Laboratory Furnace/Oven 2- Glasswares


SMEWW 4500-P C Phosphorus Doha Laboratory

1- Spectrophotometer 2- Glasswares


SMEWW 2540 C Total Dissolved Solids /Total volatile dissolved solid

Doha Laboratory



SMEWW 2540 D Total Suspended Solids/Total volatile suspended solid

Doha Laboratory



SMEWW 2540 B Total Solids Doha Laboratory




CATEGORY STD. NO./

METHOD/ISSUE DATES


SECTION

LOCATION/ FACILITY


USED (NAME/ID NO.)

NAMES OF APPROVED


Chemical SMEWW 2540 F Settleable Solids Doha Laboratory

1- Glasswares Jerry Seludo C-07 Marlon Camero C-03 Jinu Khan C-011 Shajahan Kasim C-13

SMEWW 2130 B Turbidity Doha Laboratory

1- Turbidimeter 2- Glasswares


SMEWW 2320 B Alkalinity Doha Laboratory


SMEWW 5210 D Biological Oxygen Demand Doha Laboratory

1- BOD Respirometer 2- Glasswares 3- BOD Incubator


SMEWW 9223 B Fecal Coliforms Doha Laboratory

1- Glasswares 2- Incubator


BS 1377-3:1990 Methods of test for soils for civil engineering purposes. Chemical and electro-chemical tests – Clause 7.2: Water Soluble Chloride content in soil

Doha Laboratory

1- Glasswares 2- Balance


BS 1377-3:1990 Methods of test for soils for civil engineering purposes. Chemical and electro-chemical tests –Clause 5.3 Water Soluble Sulphate content in soil

Doha Laboratory

1- Glasswares 2- Balance 3- Laboratory Hotplate 4- Laboratory Furnace


BS EN 1744-1:2009 +A1:2012

Tests for chemical properties of aggregates. Chemical analysis - Clause 12: Acid soluble Sulphate Content

Doha Laboratory



BS 812-118:1988 Testing aggregates. Methods for determination of sulphate content - Clause 9: Acid-Sulphate Content

Doha Laboratory




CATEGORY STD. NO./

METHOD/ISSUE DATES


SECTION

LOCATION/ FACILITY


USED (NAME/ID NO.)

NAMES OF APPROVED


Chemical BS 812-117:2006/1988

Testing aggregates. Method for determination of water-soluble chloride salts Appendix C: Acid soluble Chloride content-Aggregate

Doha Laboratory

1- Glasswares 2- Balance 3- Laboratory Hotplate


BS EN 1744-5:2006

Tests for chemical properties of aggregates. Determination of acid soluble chloride salts -Clause 9: Acid soluble Chloride content-Aggregate

Doha Laboratory



BS EN 1744-1:2009+A12012

Tests for chemical properties of aggregates. Chemical analysis-Clause 7: Water soluble Chloride content-

Doha Laboratory



BS 812-117:2009+A1:2012

Testing aggregates. Method for determination of water-soluble chloride salts: Clause 9: Water soluble chloride content

Doha Laboratory



BSEN 1744-1:2009+A1:2012

Tests for chemical properties of aggregates. Chemical analysis- Clause 10: Water soluble Sulphate content-

Doha Laboratory



BS 1881-124:1988 Testing concrete. Methods for analysis of hardened concrete - Clause 10.3: Sulfate

Doha Laboratory



BS 1881-124:1988 Testing concrete. Methods for analysis of hardened concrete Clause 10.2:- Chloride

Doha Laboratory



BS 1377 -3 Section 9:1990

pH in soil/groundwater Doha Laboratory

1- pH Meter 2- Balance 3- Glasswares


SMEWW 4500-Cl- B:2005

Chloride Doha Laboratory



CATEGORY STD. NO./

METHOD/ISSUE DATES


SECTION

LOCATION/ FACILITY


USED (NAME/ID NO.)

NAMES OF APPROVED


Chemical SMEWW 2510 B:2005

Conductivity Doha Laboratory

1- Conductivity Meter 2- Glasswares


BS 1377 -3 Section 8:1990

Total Dissolved Solids Doha Laboratory



BS 6068-2.51:2005 Alkalinity Doha Laboratory


SMEWW 2340 C:2005

Total Hardness Doha Laboratory


SMEWW 3500 Ca B:2005

Calcium Doha Laboratory


SMEWW 3500 Mg B:2005

Magnesium Doha Laboratory


SMEWW 5220 D:2005

Chemical Oxygen Demand Doha Laboratory

1- COD Reactor 2- Spectrophotometer 3- Glasswares


SMEWW 9223 B:2005

Total Coliforms Doha Laboratory



SMEWW 9223 B:2005

E.Coli Doha Laboratory




CATEGORY STD. NO./

METHOD/ISSUE DATES


SECTION

LOCATION/ FACILITY


USED (NAME/ID NO.)

NAMES OF APPROVED


Chemical BS 1377 - 3 Section 3:1990

Organic Matter Content in Soil

Doha Laboratory



BS 1377 - 3 Section 7.3:1990

Acid Soluble Chloride content in soil

Doha Laboratory



BS 1377 - 3 Section 5.2:1990

Acid Soluble Sulphate content in soil

Doha Laboratory



ASTM C40:2011 Organic Impurities in Aggregates

Doha Laboratory



BS EN 196-2 Cl 5:2013

Cl 5 Chemical analysis of cement- National Annex D (SiO2 ,Al2O3, Fe2o, CaO, MgO, SO3, K2O )

Doha Laboratory

1. ED-XRF Equipment (Q-CHE-XRF-01)

1. Jinu Khan - C-011 2. Marlon Camero- C-03

BS EN 196-2 Cl 4.4.1:2013

Cl 4.4.1 Loss on Ignition Doha Laboratory

1. Furnace (QIL/MUF/01) 2. Analytical Balance (QIL-BAL-14)

1. Jinu Khan - C-011 2. Marlon Camero-C-03

Geotextiles ASTM D 5199 Standard Test Method for Measuring the Nominal Thickness of Geosynthetics1

Doha Laboratory

Caliper Q-VC-18 Mould UTM Q-GTX-01

Doss Vishnu Prajeesh

ASTM D 792 Standard Test Method for Density and Specific Gravity(Relative Density) of Plastics by Displacement

Doha Laboratory

Balance Q-BL-68 Water Bath QIL-WB-04 Oven Q-OV-11 Thermometer Q-TM-158

Rouf Vishnu Naseer

ASTM D 638 Standard Test Method for Tensile Properties of Plastics

Doha Laboratory

Die Mould UTM Q-GTX-01

Prajees Doss Ajay

ASTM D 570 Standard Test Method for Water Absorption of Plastics

Doha Laboratory


Rouf Vishnu Doss

ASTM D 1004 Standard Test Method for Tear Resistance of Plastic Film and Sheeting

Doha Laboratory


Naseer Prajeesh Vishnu

ASTM E 154 -08a (Cl 10 )

Standard Test Method for Resistance to Puncture

Doha Laboratory

UTM Q-GTX-01 Mould

Naseer Ajay Prajeesh


CATEGORY STD. NO./

METHOD/ISSUE DATES


SECTION

LOCATION/ FACILITY


USED (NAME/ID NO.)

NAMES OF APPROVED


Geotextiles ASTM D 882 Standard Test Method for Tensile Properties of Thin Plastic Sheeting1

Doha Laboratory


Rouf Ajay Doss

ASTM D 1622 Standard Test Method for Apparent Density of Rigid Cellular Plastics

Doha Laboratory


Doss Rouf Naseer

ASTM C 203-05a Standard Test Methods for Breaking Load and Flexural Properties of Block-Type Thermal Insulation

Doha Laboratory

Compression machine Q-CBR-02 Steel Balls

Doss Naseer Rouf

ASTM D 1621 Standard Test Method for Compressive Properties of Rigid Cellular Plastics

Doha Laboratory

Compression machine Q-CBR-02 Steel Plates

Naseer Vishnu Prajeesh

ASTM D 2842 Standard Test Method for Water Absorption of Rigid Cellular Plastics

Doha Laboratory


Doss Rouf Prajeesh

ASTM D 1751 Sections 5.2-5.4

Standard Specification for Preformed Expansion Joint Filler for Concrete Paving and Structural Construction (Nonextruding and Resilient Bituminous Types)

Doha Laboratory

Compression machine Q-CBR-02

Ajay Prajeesh Vishnu

ASTM D 5034 Standard Test Method for Breaking Strength and Elongation of Textile Fabrics

Doha Laboratory

Die Mold UTM Q-GTX-01

Ajay Naseer Prajeesh

ASTM D 4595 Standard Test Method for Tensile Properties of Geotextiles by the Wide-Width Strip Method

Doha Laboratory

UTM Q-GTX-01 Mould

Prajeesh Doss Vishnu

ASTM D412 Clause 16

Standard Test Methods for Vulcanized Rubber and Thermoplastic Elastomers— Tension

Doha Laboratory


Doss Ajay Prajeesh

ASTM D751 Textile Puncture Resistance Street 43 Lab UTM Q-GTX-01 Mould Q-GXT-CBR Mould-01"

Naseer Ajay Prajeesh

ASTM D4533 Trapezoid Tearing Strength of Geotextiles

Street 43 Lab Scissors ASTM Ruler QR-09 Caliper - Q-VC-018 UTM Q-GTX-01 Grip Q-GXT-Grip-02"


ASTM D5035 Breaking Force and Elongation of Textile Fabrics (Strip Method)

Street 43 Lab Scissors Ruler UTM Q-GTX-01


BS EN ISO 527 Part-3

Determination of tensile properties

Street 43 Lab Grip Q-GTX-GRIP-02 UTM Q-GTX-01 Die Q-GTX-DIE-04

Prajees Doss Ajay


CATEGORY STD. NO./

METHOD/ISSUE DATES


SECTION

LOCATION/ FACILITY


USED (NAME/ID NO.)

NAMES OF APPROVED


Geotextiles BS EN ISO 9864 Test method for the determination of mass per unit area of geotextiles and geotextile-related products

Street 43 Lab Balance Q-BL-68 Water Bath QIL-WB-04 Oven Q-OV-11 Thermometer Q-TM-158

Rahoof Vishnu Naseer

BS EN ISO 10319 Wide-width tensile test Street 43 Lab UTM Q-GTX-01 Grip Q-GTX -GRIP-04 Caliper Q-VC-018


Date post:	09-Sep-2018
Category:	Documents
Upload:	trinhnguyet
View:	237 times
Download:	1 times

QATAR INDUSTRIAL LABORATORIES W - qilqatar.comqilqatar.com/_doc/ias-cert-2017.pdf · This...

Documents