1
Regd. Office: Plot No. A-40, Unit: A -301-302, 3rd Floor, I- Thum IT Tower, Sec 62, Noida E-mail: [email protected] www.trainingbasket.in 9015887887 9899080002 TRAINING BASKET QUALIFY FOR TOMORROW Geometry Ÿ Understanding STAAD Pro Way Ÿ What are Nodes, Beams and Plates? Ÿ How things are done in the Input file? Ÿ Geometry Creation ethods Ÿ Method 1: Using Structure Wizard Ÿ Things you can do in Structure Wizard Ÿ Method 2: Drafting the eometry using Snap/Grid Ÿ Viewing Ÿ Selecting Ÿ Using SelectingWhile Viewing 3D Geometry Ÿ Method 3: Using Copy/Cut with Paste Ÿ Method 4: Using Spreadsheet (Excel) Copy and Paste Ÿ Method 5: Using DXF importing file function Ÿ Workshop Ÿ Module Review Useful Function to omplete the Geometry Ÿ Introduction Ÿ Translational epeat Ÿ Circular Repeat Ÿ Mirror Ÿ Rotate Ÿ Move Ÿ Insert Node Ÿ Add Beam Between Mid-Points Ÿ Add Beam by Perpendicular Intersection Ÿ Connect Beams along an Axis Ÿ Intersect Selected Members Ÿ Cut Section Ÿ Renumber Ÿ Delete Ÿ Undo/Redo Ÿ Zooming/Panning Ÿ Dimensioning Ÿ Pointing to odes, Beams, and Plates Ÿ Global and Local Coordinate System Ÿ Workshop Ÿ Module Review Properties Ÿ Introduction Ÿ Property Types Ÿ Type 1: Prismatic Ÿ Viewing Cross-Section Ÿ Type 2: Built-In Steel Table Ÿ Type 3: Thickness Ÿ General Notes about Property Assigning Ÿ Workshop Ÿ Module Review Constants, Supports, and Specificaations Ÿ Introduction Ÿ Material Constants Ÿ Geometry Constant Ÿ Supports Ÿ How to Assign Supports Ÿ Editing upports Ÿ Specificaations Ÿ Workshop Ÿ Module Review Loading Ÿ Introduction Ÿ How to Create Primary Load Ÿ Individual Loads: Introduction Ÿ Individual Loads: Selfweight Ÿ Individual Loads: Members Loads Ÿ Individual Loads: Area Load Ÿ Individual Loads: Floor Load Ÿ Individual Loads: Plate Loads Ÿ Individual Loads: Node Load Ÿ Individual Loads: Viewing & Editing Ÿ How to Create Manual Combinations Ÿ How to Create Automatic ombinaations Ÿ Workshop Ÿ Module Review Analysis Ÿ Introduction Ÿ Perform Analysis Command Ÿ P-Delta Analysis Command Ÿ Non-Linear Analysis Command Ÿ The Execution ommand Ÿ Workshop Ÿ Module Review Post Processing Ÿ Introduction Ÿ First Step Ÿ Node Displacement Ÿ Node Reactions Ÿ Beam Forces Ÿ Beam Stresses Ÿ Beam Graphs Ÿ Plate Contour Ÿ Plate Results Along Line Ÿ Animation Ÿ Reports STAADpro
![0 h} 0...302.68329.89 ÿ h*_S0_0 _Sg } R)vÊ Ñ M ÿ Q ÿ ÿ ÿ ÿ 43.4645.83 o\W(h*_ ¿et_ ÿ h*_S0_0 _S g } R)vÊ Ñ M ÿ Q ÿ ÿ ÿ ÿ 40.1543.43 ê]ñ Çg,kÔs ÿ ÿ ÿ ÿ ÿ ÿ](https://static.documents.pub/doc/80x56/60ba50d9c1c28e561c44a1f7/0-h-0-3026832989-hs00-sg-rv-m-q-43464583.jpg)
