Disclaimer: Information may be subject to changes without prior notification www.engenius-europe.com Package content - CPE - PoE injector - Power adapter - Quick start guide - Wall mount screw set - Pole Mounting Strap Minimum requirements Broadband Internet Service: Cable or DSL modem Internet browser: Internet Explorer, Safari, Firefox, Chrome Connecting the CPE 1. Remore the rear bottom panel. 2. Connect one end of the Ethernet cable into the LAN (PoE) port of the CPE and the other end to the PoE ethernet port on the PoE injector. 3. Connect the Power adapter to the DC-IN port of the CPE and plug the other end into an electrical outlet. 4. Connect the second end of the Ethernet cable into the LAN port of the PoE injector and the other end to the Ethernet port on the computer. 5. Place the panel removed from step 1 back into the device. Note: The CPE should ONLY be powered via Ethernet cable connected to the included PoE injector. EnStation2 | EnStation5
Transcript
Disclaimer: Information may be subject to changes without prior noti� cationwww.engenius-europe.com
Package content- CPE- PoE injector- Power adapter- Quick start guide- Wall mount screw set- Pole Mounting Strap
Minimum requirementsBroadband Internet Service: Cable or DSL modemInternet browser: Internet Explorer, Safari, Firefox, Chrome
Connecting the CPE1. Remore the rear bottom panel.2. Connect one end of the Ethernet cable into the LAN (PoE) port of the CPE and the other end to the PoE ethernet port on the PoE injector.3. Connect the Power adapter to the DC-IN port of the CPE and plug the other end into an electrical outlet.4. Connect the second end of the Ethernet cable into the LAN port of the PoE injector and the other end to the Ethernet port on the computer.5. Place the panel removed from step 1 back into the device.
Note: The CPE should ONLY be powered via Ethernet cable connected to the included PoE injector.
EnStation2 | EnStation5
Disclaimer: Information may be subject to changes without prior noti� cationwww.engenius-europe.com
IP Address con� guration1. Once your computer is on, ensure that your TCP/IP is set to On or Enabled. Open Network Connections and then click Local Area Connection. Select Internet Protocol Version 4 (TCP/IPv4).
2. If your computer is already on a network, ensure that you have set it to a Static IP Address on the interface. (Example: 192.168.1.10)
CPE setup1. To con� gure the CPE, open a web browser. In the address bar of the web browser, enter 192.168.1.1 and hit enter.
2. A login screen will appear. By default, the username of the CPE is admin and the password is admin. Enter the current username and password of the CPE and then click Login.
Switching modes1. The device can operate in the following modes: access point, client bridge, WDS and client router. 2. Click on the Operation mode link under the System properties.
EnStation2 | EnStation5
Wall mounting the CPE1. Plug the dynamic stick into the bracket � rstly.2. Combine the sealing nut and combined kit, as well as tighten it. 3. Put the nock washer on dynamic stick.4. Assemble the mounting kit with the CPE.5. Drill the holl to input the mounting screws.6. Use the included scrrews to input into the mounting screws.7. Let the hole of the bracket to aim at the screws on the wall and hang the device to � x it.
Poll mounting the CPE1. Plug the dynamic stick into the bracket � rstly.2. Combine the sealing nut and combined kit, as well as tighten it.3. Put the nock washer on dynamic stick.4. Assemble the mounting kit with the CPE.5. Thread the open end of the pole strap through the tabs on the bracket.6. Lock and tighten pole strap to secure bracket to the pole.
Disclaimer: Information may be subject to changes without prior noti� cationwww.engenius-europe.com
