1/2''-5/8'' (12-15mm)3/8''-1/2'' (10-12mm)

Front Left

Surround Left

Surround Back Left

Surround Back Right

Surround RightListener

TV

Su

bw

oo

fer

Front Right

Center

Front Left

Surround Left

Surround Back Left

Surround Back Right

Surround RightListener

Front Right

CenterSu

bw

oo

fer

TV

Front HighLeft

Front HighRight

*1 *1

*1 The same signal is output from each jack.

Surroundback right speaker

Surroundright

speaker

Surroundleft

speaker

Surroundback left speaker

Powered subwoofer

Front high leftspeaker

Front left

speaker

Front high right speaker

Front right

speaker

Centerspeaker

Surroundback right speaker

Surroundright

speaker

Surroundleft

speaker

Surroundback left speaker

Powered subwoofer

Front high leftspeaker

Front left

speaker

Front high right speaker

Front right

speaker

Centerspeaker

SN 29344959 (C) Copyright 2009 ONKYO CORPORATION Japan. All rights reserved.

See the other side of this sheet for the AV component hookup.

Speaker Hookup

Thank you for purchasing this product. This quick setup sheet shows the typical hookup method for connecting speakers and AV components (DVD player, TV, cable/satellite receiver). For more detailed hookup information and operating instructions, please see the Instruction Manual.

< North American / Taiwan models >

QUICK SETUP

Speaker Layout (Main Room)

* 2 9 3 4 4 9 5 9 *

< Other models >

Model : TX-SR607

TV

HDMI IN

TVVIDEO 1

IN

HDMIOUT Antenna input

(e.g., RF IN)

Cable/satellitereceiver

Cable/satellitereceiver VIDEO

OUTAUDIO OUT

L

R

DIGITAL OUT

COAXIAL

Antenna input (e.g..RF IN)

DVD player VIDEOOUT

AUDIO OUT

DIGITAL OUT

COAXIAL L

R

HDMIOUT DVD/BD player

AV Component Hookup

IF NO HDMI

Please ensure the monitor input(VIDEO 1, VIDEO 2, VIDEO 3, etc.) selected corresponds to actualconnection used.

See the other side of this sheet for the Speaker hookup.

With an HDMI cable you can send both audio and video with a single cable, making connecting simple and keeping wires neat. If you have an HDMI-compatible TV and players, you can connect them to the AV receiver with HDMI cables. Digital audio signals received at HDMI IN input are output by the speakers and headphones connected to the AV receiver.

Coaxial feed from TV antennaIf you are not usingcable/satellite receiver,please refer to theinstruction manual.

Coaxial feed from TV antennaIf you are not usingcable/satellite receiver,please refer to theinstruction manual.

If your TV or player doesn ’t support HDMI, use the analog or digital connections shown below.

Using the HDMI InputsIf there’s no picture on your TV, you’ll need to assign the HDMI inputs as necessary using theonscreen setup menus.If you connect your DVD/BD player to the AV receiver’s HDMI IN 1, and connect your cable/satellite receiver to HDMI IN 3, as shown above, it’s not necessary to change the default assignments.

Using the Digital InputsIf there’s no sound, you’ll need to assign the digital inputs as necessary using the setup menus on the AV receiver’s display.If you connect your DVD player to the AV receiver’s DIGITAL IN COAXIAL 1, and your cable/satellite receiver to the DIGITAL IN COAXIAL 2, as shown, it’s not necessary to assign the digital input.

The onscreen setup menus appear only on a TV that is connected to the HDMI OUT. If your TV is connected to the MONITOR OUT or the COMPONENT VIDEO OUT, use the AV receiver’s display when changing settings.

On the front panel On the front panel

1–1. HDMI Input DVD/BDVCR/DVRCBL/SATGAMEAUX

HDMI 1HDMI 2HDMI 3HDMI 4FRONT

1. Input Assign 1. HDMI Input2. Component Video Input3. Digital Audio Input

Menu 1. Input Assign 2. Speaker Setup3. Audio Adjust4. Source Setup5. Listening Mode Preset6. Miscellaneous7. Hardware Setup8. Remote Controller Setup9. Lock Setup