FrontLeft
SurroundLeft
SurroundBackLeft
SurroundBackRight
SurroundRightListener
TV
Su
bw
oo
fer
FrontRight
Center
FrontLeft
SurroundLeft
SurroundBackLeft
SurroundBackRight
SurroundRightListener
TV
FrontRight
CenterSu
bw
oo
fer
5/8''(15mm)
Surround rightspeaker
Surround backright speaker
Surround backleft speaker
Surroundleft speaker
Poweredsubwoofer
Front leftspeaker
Front rightspeaker
Centerspeaker
SN 29344740(C) Copyright 2008 ONKYO CORPORATION Japan. All rights reserved.
See the other side of this sheet for the AV component hookup.
Speaker Hookup
Thank you for purchasing this product.This quick setup sheet shows the typical hookup method for connectingspeakers and AV components (DVD player, TV, cable/satellite receiver).For more detailed hookup information and operating instructions,please see the Instruction Manual.
QUICK SETUPModel : TX-SR806/TX-SA806
Speaker Layout (Main Room)
* 2 9 3 4 4 7 4 0 *
DVD player
TV
HDMIIN
TVVIDEO 1
IN
HDMIOUT Antenna input
(e.g., RF IN)
Cable/satelliteCable/satellite VIDEO
OUTAUDIOOUT
L
R
DIGITALOUT
COAXIAL
Antenna input(e.g..RF IN)
DVD playerVIDEOOUT
AUDIOOUT
DIGITALOUT
COAXIAL L
R
HDMIOUT
AV Component Hookup
IF NO HDMI
See the other side of this sheet for the Speaker hookup.
With an HDMI cable you can send both audio and video with a single cable, making connecting simple and keeping wires neat.If you have an HDMI-compatible TV and players, you can connect themto the AV receiver/AV amplifier with HDMI cables. Digital audio signals received at HDMI IN input are output by the speakers and headphones connected to the AV receiver/AV amplifier.
If your TV or player doesn’t support HDMI, use the analog or digitalconnections shown below.
Please ensure the monitor input (VIDEO 1, VIDEO 2, VIDEO 3, etc.) selected corresponds to actual connection used.
Coaxial feed from TV antennaIf you are not usingCable/satellite box,please refer to theinstruction manual.
Coaxial feed from TV antennaIf you are not usingCable/satellite box,please refer to theinstruction manual.
Using the Digital InputsIf there’s no sound, you’ll need to assign the digital inputs as necessary using the onscreen setup menus.If you connect your DVD player to the AV receiver/AV amplifier’s DIGITAL COAXIAL IN 1, and your cable/satellite receiver to the DIGITAL COAXIAL IN 3, as shown, it’s not necessary to assign the digital input.
Using the HDMI InputsIf there’s no picture on your TV, you’ll need to assign the HDMI inputs as necessary using theonscreen setup menus.If you connect your DVD player to the AV receiver/AV amplifier’s HDMI IN 1, and connect your cable or satellite receiver to HDMI IN 3, as shown above, it’s not necessary to change the default assignments.
1–1. HDMI InputDVDVCR/DVRCBL/SATGAME/TVAUX
HDMI 1HDMI 2HDMI 3HDMI 4- - - - -
MENU1. Input Assign2. Speaker Setup3. Audio Adjust4. Source Setup5. Listening Mode Preset6. Miscellaneous7. Hardware Setup8. Lock Setup
1. Input Assign1. HDMI Input2. Component Video Input3. Digital Audio Input
MENU1. Input Assign2. Speaker Setup3. Audio Adjust4. Source Setup5. Listening Mode Preset6. Miscellaneous7. Hardware Setup8. Lock Setup
1. Input Assign1. HDMI Input2. Component Video Input3. Digital Audio Input
1–3. Digital Audio InputDVDVCR/DVRCBL/SATGAME/TVAUX
COAX 1COAX 2COAX 3
OPT 1FRONT
On the front panel On the front panel
In addition, you must set the “Monitor Out” setting to “Analog” by pressing the [HDMI OUT] button first.