Quick Start(V100R005 02)

Quidway S2300/S3300/S5300 Series EthernetSwitchesV100R005

Quick Start

Issue 02

Date 2010-12-01

HUAWEI TECHNOLOGIES CO., LTD.

Copyright © Huawei Technologies Co., Ltd. 2010. All rights reserved.No part of this document may be reproduced or transmitted in any form or by any means without prior writtenconsent of Huawei Technologies Co., Ltd. Trademarks and Permissions

and other Huawei trademarks are trademarks of Huawei Technologies Co., Ltd.All other trademarks and trade names mentioned in this document are the property of their respective holders. NoticeThe purchased products, services and features are stipulated by the contract made between Huawei and thecustomer. All or part of the products, services and features described in this document may not be within thepurchase scope or the usage scope. Unless otherwise specified in the contract, all statements, information,and recommendations in this document are provided "AS IS" without warranties, guarantees or representationsof any kind, either express or implied.

The information in this document is subject to change without notice. Every effort has been made in thepreparation of this document to ensure accuracy of the contents, but all statements, information, andrecommendations in this document do not constitute the warranty of any kind, express or implied.

Huawei Technologies Co., Ltd.Address: Huawei Industrial Base

Bantian, LonggangShenzhen 518129People's Republic of China

Website: http://www.huawei.com

Email: [email protected]

Issue 02 (2010-12-01) Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.

i

http://www.huawei.com

mailto:[email protected]

About This Document

Intended AudienceThe intended audiences of this document are:

l Installation engineers

l Commissioning engineers

l On-site maintenance engineers

l System maintenance engineers

Symbol ConventionsThe symbols that may be found in this document are defined as follows.

Symbol Description

DANGERIndicates a hazard with a high level of risk, which if notavoided, will result in death or serious injury.

WARNINGIndicates a hazard with a medium or low level of risk, whichif not avoided, could result in minor or moderate injury.

CAUTIONIndicates a potentially hazardous situation, which if notavoided, could result in equipment damage, data loss,performance degradation, or unexpected results.

TIP Indicates a tip that may help you solve a problem or savetime.

NOTE Provides additional information to emphasize or supplementimportant points of the main text.

Command ConventionsThe command conventions that may be found in this document are defined as follows.

Quidway S2300/S3300/S5300 Series Ethernet SwitchesQuick Start About This Document


iii

Convention Description

Boldface The keywords of a command line are in boldface.

Italic Command arguments are in italics.

[ ] Items (keywords or arguments) in brackets [ ] are optional.

{ x | y | ... } Optional items are grouped in braces and separated byvertical bars. One item is selected.

[ x | y | ... ] Optional items are grouped in brackets and separated byvertical bars. One item is selected or no item is selected.

{ x | y | ... }* Optional items are grouped in braces and separated byvertical bars. A minimum of one item or a maximum of allitems can be selected.

[ x | y | ... ]* Optional items are grouped in brackets and separated byvertical bars. Several items or no item can be selected.

&<1-n> The parameter before the & sign can be repeated 1 to n times.

# A line starting with the # sign is comments.

Change HistoryChanges between document issues are cumulative. Therefore, the latest document issue containsall changes made in previous issues.

Changes in Issue 02 (2010-12-01)Compared with issue 01, the changes of this version are as follows:l Step 1 and step 6 in 1.5.2 Example for Configuring to Manage the SwitchThrough

Telnet are optimized.

Changes in Issue 01 (2010-08-15)Initial commercial release.

About This DocumentQuidway S2300/S3300/S5300 Series Ethernet Switches

Quick Start

iv Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.

Issue 02 (2010-12-01)

Contents

About This Document...................................................................................................................iii

1 Quick Start...................................................................................................................................1-11.1 Overview.........................................................................................................................................................1-21.2 Product Hardware Introduction.......................................................................................................................1-2

1.2.1 S2300/S3300/S5300 Introduction..........................................................................................................1-31.2.2 S2300 Indicator Description...................................................................................................................1-41.2.3 S3300 Indicator Description...................................................................................................................1-91.2.4 S5300 Indicator Description.................................................................................................................1-15

1.3 Device Installation.........................................................................................................................................1-251.4 Powering on the Device................................................................................................................................1-25

1.4.1 Checking Before Power-on..................................................................................................................1-251.4.2 Powering on the Device.......................................................................................................................1-301.4.3 Checking After Power-on.....................................................................................................................1-30

1.5 Logging in to the Device...............................................................................................................................1-301.5.1 Logging In to the Switch Through the Console Interface....................................................................1-301.5.2 Example for Configuring to Manage the SwitchThrough Telnet.........................................................1-331.5.3 Logging In to the Web System Client..................................................................................................1-36

1.6 Service Deployment......................................................................................................................................1-371.7 Obtaining Documentation.............................................................................................................................1-37

Quidway S2300/S3300/S5300 Series Ethernet SwitchesQuick Start Contents


v

Figures

Figure 1-1 Quick start contents............................................................................................................................1-2Figure 1-2 S2309TP-SI/EI indicators...................................................................................................................1-5Figure 1-3 S2326TP-PWR-EI indicators.............................................................................................................1-6Figure 1-4 Schematic diagram of S3328TP-SI/EI indicators...............................................................................1-9Figure 1-5 Schematic diagram of S3352P-PWR-EI indicators..........................................................................1-10Figure 1-6 Schematic diagram of S5324TP-SI indicators..................................................................................1-15Figure 1-7 Schematic diagram of S5328C-PWR-SI indicators..........................................................................1-20Figure 1-8 Setting up a connection.....................................................................................................................1-31Figure 1-9 Configuring the interface for connection..........................................................................................1-31Figure 1-10 Specifying parameters....................................................................................................................1-32Figure 1-11 Selecting the terminal type.............................................................................................................1-33Figure 1-12 Networking diagram of managing SwitchA through Telnet..........................................................1-34Figure 1-13 Login...............................................................................................................................................1-37

Quidway S2300/S3300/S5300 Series Ethernet SwitchesQuick Start Figures


vii

Tables

Table 1-1 S2300/S3300/S5300 models................................................................................................................ 1-3Table 1-2 Indicator description of Non-PoE S2300s............................................................................................1-5Table 1-3 Indicator description of PoE S2300s....................................................................................................1-6Table 1-4 Meanings represented by the statuses of interface indicators in different modes................................1-8Table 1-5 Indicator description of the S3300s not enabled with PoE..................................................................1-9Table 1-6 Indicator description of S3300s enabled with PoE............................................................................1-10Table 1-7 Meanings represented by the status of interface indicators in different display modes.....................1-14Table 1-8 Indicator description of devices with single power modules.............................................................1-15Table 1-9 Indicator description of devices with dual power modules................................................................1-17Table 1-10 Meanings represented by the status of interface indicators in different display modes...................1-19Table 1-11 Indicator description of S5300s enabled with PoE..........................................................................1-21Table 1-12 Meanings represented by the status of interface indicators in different display modes...................1-24Table 1-13 Device installation checklist............................................................................................................1-26Table 1-14 Cable installation checklist..............................................................................................................1-28Table 1-15 Cabinet cable checklist.....................................................................................................................1-29Table 1-16 Signal cable checklist.......................................................................................................................1-29Table 1-17 Parameters........................................................................................................................................1-32

Quidway S2300/S3300/S5300 Series Ethernet SwitchesQuick Start Tables


ix

1 Quick Start

About This Chapter

1.1 OverviewThis section provides an overview of quick start.

1.2 Product Hardware IntroductionThis section describes models and indicators of low-end switches.

1.3 Device InstallationThis section describes how to install the S2300/S3300/S5300.

1.4 Powering on the DeviceThis section describes the check items and the procedure for powering on and powering off thedevice.

1.5 Logging in to the DeviceThis section describes how to log in to the device.

1.6 Service DeploymentThis section describes service deployment.

1.7 Obtaining DocumentationCurrently, in addition to the documents delivered with the device, you can obtain thedocumentation in the following ways:

Quidway S2300/S3300/S5300 Series Ethernet SwitchesQuick Start 1 Quick Start


1-1

1.1 OverviewThis section provides an overview of quick start.

This document helps you quickly learn how to use the S2300/3300/5300. Figure 1-1 shows thequick start contents.

Figure 1-1 Quick start contents

Start

Product description

Describe indicators on low-end switches

Device installation

Describe how to log in to the low-end switch

Device power-on

Device login

Describe precautions on low-end switches before and after power-on

Describe device login

Service deployment

Describe how to rapidly deploy services on low-end switches

Document obtaining

Describe how to obtain the documentation

1.2 Product Hardware IntroductionThis section describes models and indicators of low-end switches.

1.2.1 S2300/S3300/S5300 IntroductionThis section describes S2300/S3300/S5300 models.

1.2.2 S2300 Indicator Description



1 Quick StartQuidway S2300/S3300/S5300 Series Ethernet Switches

Quick Start

1-2 Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.

Issue 02 (2010-12-01)

1.2.1 S2300/S3300/S5300 IntroductionThis section describes S2300/S3300/S5300 models.

Table 1-1 describes S2300/S3300/S5300 models.l P: indicates that uplink ports are SFP optical ports.l T: indicates that uplink ports are RJ45 electrical ports.l TP: indicates that uplink ports include both electrical ports and optical ports.l C: indicates that uplink ports can be configured as required.l AC: indicates that AC power supply is used.l DC: indicates that DC power supply is used.l S: indicates optical ports.l PWR: supports PoE.l SI: indicates the standard version, supporting basic features.l EI: indicates the enhanced version, supporting certain advanced features.

The number of uplink ports can be 8, 16, 24, or 48. The S2309TP-SI is configured with eightdownlink ports and one uplink port; The S3352P-EI-24S is configured with 48 downlink portsand four uplink ports. Among the downlink ports, there are 24 electrical ports and 24 opticalports.

Table 1-1 S2300/S3300/S5300 models

Series Models

Quidway S2300 series Quidway S2300 series have the following modules:l S2309TP-SIl S2309TP-EIl S2318TP-SIl S2318TP-EIl S2326TP-SIl S2326TP-EIl S2352P-EIl S2309TP-PWR-EIl S2326TP-PWR-EI



1-3

Series Models

Quidway S3300 series Quidway S3300 series have the following modules:l S3328TP-SIl S3328TP-EIl S3328TP-EI-24Sl S3328TP-EI-MCl S3352P-EI-24Sl S3352P-EI-48Sl S3352P-SIl S3352P-EIl S3328TP-PWR-EIl S3352P-PWR-EI

Quidway S5300 series Quidway S5300 series have the following modules:l S5328C-EIl S5328C-EIl S5328C-EI-24Sl S5352C-EIl S5328C-PWR-EIl S5352C-PWR-EIl S5328C-SIl S5352C-SIl S5328C-PWR-SIl S5352C-PWR-SIl S5324TP-SIl S5348TP-SIl S5324TP-PWR-SIl S5348TP-PWR-SI


Indicator Description of Non-PoE S2300sThe following takes the S2309TP-SI/EI as an example to describe the indicators of Non-PoES2300s.


Quick Start


Issue 02 (2010-12-01)

Figure 1-2 S2309TP-SI/EI indicators

4

3 2

1

Table 1-2 Indicator description of Non-PoE S2300s

No. Indicator Identifier Status Description

1 Powerindicator

PWR Off The device is powered off.

On The power supply of thedevice is normal.

2 Systemrunningindicator

RUN Off The system is not running.

On The system runs abnormally oris being started.

Blinkinggreen

The system runs normally.

3 Interfaceindicator

LNK/ACT Off The interface is not connectedor is shut down.

4 On The interface is connected.

Blinkinggreen

The interface is sending orreceiving data.

Indicator Description of the S2326TP-PWR-EIThe following takes the S2326TP-PWR-EI as an example to describe the indicators of the S2300senabled with PoE.

NOTE

The S2309TP-PWR-EI has only one power module.



1-5

Figure 1-3 S2326TP-PWR-EI indicators

1

2

3

4

5

Table 1-3 Indicator description of PoE S2300s


1 Powerindicator

PWR1 Off The board power supply isabnormal if the powermodule is not installed or asingle power module isconfigured.

On The power supply isnormal.

Blinking red The possible causes are asfollows:l When the switch is

equipped with twopower modules, thepower modules arepowered off.

l Power modules arepowered off.

l The board powersupply and PoE powersupply are abnormal.

Blinkingorange

The PoE power module isabnormal when a singlepower module isconfigured. The boardpower supply or PoEpower supply is abnormalwhen dual power modulesare configured.


Quick Start


Issue 02 (2010-12-01)


2 Powerindicator

PWR2 Off The board power supply isabnormal if the powermodule is not installed or asingle power module isconfigured.

On The power supply isnormal.

Blinking red The possible causes are asfollows:l The power module is

installed but is poweredoff when dual powermodules areconfigured.

l The power module ispowered off.

l The board powersupply and PoE powersupply are abnormal.

Blinkingorange

The PoE power supply isabnormal when a singlepower module isconfigured; or the board orPoE power supply isabnormal when dual powermodules are configured.

3 Runningstatusindicator

SYS Off The system is not running.

On The system runsabnormally or is beingstarted.

Blinkingorange

The system performs self-check during startup.

Blinking green The system runs normally.

Blinking red After the device isregistered, the systemworks abnormally, or thealarm about the powermodule failure, the fanmodule failure, or theabnormal temperature isgenerated.



1-7


4 Modeindicator

- Off The service interfaceindicator is in defaultmode, that is, the interfaceis in STAT state.

On The service interfaceindicator indicates thespeed of the interface.After 30s, the serviceinterface indicatorautomatically restores tooff.

Blinkingorange

The service interfaceindicator indicates the PoEstatus temporarily. After30s, the service interfaceindicator automaticallyrestores to off.

As shown in Figure 1-3, 5 shows the mode switching button. On an S2300, you can press themode switching button to switch the display modes of interface indicators. The status of a modeindicator represents the display mode of the related interface indicator. Take the S2309TP-PWR-EI for example. When you press the mode switching button for the first time, the mode indicatorturns green and the related interface indicator enters the speed state. When you press the modeswitching button for the second time, the mode indicator turns orange and the related interfaceindicator displays the PoE information. When you press the mode switching button for the thirdtime, the mode indicator restores to the default state, that is, off. If you do not press the modeswitching button for 30s, the mode indicator automatically restores to off.

The following table describes the meanings represented by the statuses of interface indicatorsin different modes.

Table 1-4 Meanings represented by the statuses of interface indicators in different modes

Display Mode Status Description

STAT Off The interface is not connected oris shut down.

On The interface is connected.

Blinking green The interface is sending orreceiving data.

Speed Off The interface is not connected oris shut down.

On The interface runs at a speed lowerthan 10/100 Mbit/s.


Quick Start


Issue 02 (2010-12-01)

Display Mode Status Description

Blinking green The interface runs at a speed lowerthan 1000 Mbit/s.

PoE Off The interface is not poweredremotely.

On The interface is not poweredremotely.

Blinking green The possible cause is as follows:l The power of the PD exceeds

the power supply capability ofthe interface or the threshold.


Indicator Description of the S3300s Not Enabled with PoE

The following takes the S3328TP-SI/EI as an example to describe the indicators of theS3300s not enabled with PoE.

Figure 1-4 Schematic diagram of S3328TP-SI/EI indicators

3 21

Table 1-5 Indicator description of the S3300s not enabled with PoE


1 Powerindicator

PWR Off The device is powered off.

Green The power supply of thedevice is normal.

2 Systemoperatingstatusindicator

RUN Off The system is not running.

Green The system runs abnormally oris being started.



1-9


Blinkinggreen

The system runs normally.

3 interfaceindicators

LNK/ACT Off The interface has noconnection or is shut down.

Green The interface has connections.

Blinkinggreen

The interface is sending orreceiving data.

Indicator Description of the S3300s Enabled with PoEThe following takes the S3352P-PWR-EI as an example to describe the indicators of the S3300senabled with PoE.

Figure 1-5 Schematic diagram of S3352P-PWR-EI indicators

1

2

3

4

5

Table 1-6 Indicator description of S3300s enabled with PoE


1 Powerindicator

PWR1 Off The power supplymodule is not inposition or the boardpower supply isabnormal during theconfiguration of thesingle power module.

Green The power supply isnormal.


Quick Start


Issue 02 (2010-12-01)


Red The possible causesare as follows:l The power

module is inposition but thepower switch isturned off duringthe configurationof dual powermodules.

l The device is notconnected to thepower module.

l The board powersupply and PoEpower supply arefaulty.

Amber The PoE powersupply is abnormalduring theconfiguration of thesingle power module;or the board or PoEpower supply isabnormal during theconfiguration of dualpower modules.

2 Powerindicator

PWR2 Off The power supplymodule is not inposition or the boardpower supply isabnormal during theconfiguration of thesingle power module.




1-11








SYS Off The system is notrunning.

Green The system runsabnormally or isbeing started.

Amber The indicatorperforms self-checkat startup.

Blinking green The system runsnormally.

Red The system runsabnormally after thedevice is registered;or abnormalityalarms about thepower supply, fan, ortemperature aregenerated.


Quick Start


Issue 02 (2010-12-01)


4 Mode switchindicator

- Off The interfaceindicators are in thedefault mode,indicating the STATstatus of interfaces.

Green The interfaceindicatorstemporarily indicatethe Speed status ofinterfaces. Theinterface indicatorsrestore the defaultmode (off) in 30s.

Amber The interfaceindicatorstemporarily indicatethe PoE status ofinterfaces. Theinterface indicatorsrestore the defaultmode (off) in 30s.

Red The interfaceindicatorstemporarily indicatethe Stack status ofinterfaces. Theinterface indicatorsrestore the defaultstatus (off) in 30s.

As shown in Figure 1-5, No.5 shows the mode switch button. On an S3300, you can press themode switch button to switch the display modes of interface indicators. The status of the modeindicator represents the display mode of interface indicators. Take the S3352P-PWR-EI forexample. By default, the mode indicator is off and the interfaces are in the STAT status. Whenyou press the mode switch button for the first time, the mode indicator turns green and theinterface indicators indicate the Speed status of interfaces. When you press the mode switchbutton for the second time, the mode indicator turns amber and the interface indicators indicatethe PoE status of interfaces. When you press the mode switch button for the third time, the modeindicator turns red and the interface indicators indicate the Stack status of interfaces. When youpress the mode switch button for the fourth time, the mode indicator restores the default status,that is, Off. If you do not press the mode switch button for 30s, the mode indicator turns off.

The following table shows the meanings represented by the status of interface indicators indifferent display modes.



1-13

Table 1-7 Meanings represented by the status of interface indicators in different display modes

Display Mode Status Meaning

STAT Off The interface has no connection oris shut down.



Speed Off The interface has no connection oris shut down.

Green The interface runs at a speed of 10Mbit/s or 100 Mbit/s.

Blinking green The interface runs at a speed of1000 Mbit/s.

PoE Off The interface has no remote powersupply.

Green The interface has remote powersupply.

Blinking green The possible causes are asfollows:l The power of the power-

receiving device exceeds theset threshold or the powersupply capacity of theinterface.

Stack Off The stacking ID of the memberswitch is not the number of theinterface in the Off state.

Green The device is not a Master switch:l If the indicator of a certain

interface is solid green, itindicates that the number ofthe interface is the stacking IDof the device and the device isnot a Master switch.

l If the first nine interfaceindicators of the device aresolid green, it indicates that thestacking ID of the device is 0and the device is not a Masterswitch.


Quick Start


Issue 02 (2010-12-01)


Blinking green The device is a Master switch:l If the indicator of a certain

interface is blinking green, itindicates that the number ofthe interface is the stacking IDof the device and the device isa Master switch.

l If the first nine interfaceindicators of the device areblinking green, it indicates thatthe stacking ID of the device is0 and the device is a Masterswitch.


Indicator Description of the S5300s Not Enabled with PoE

The following takes the S5324TP-SI as an example to describe the indicators of the S5300s withsingle power modules and not enabled with PoE.

NOTE

Among all S5300s, only the S5348TP-SI and S5324TP-SI have RPS indicators at present.

Figure 1-6 Schematic diagram of S5324TP-SI indicators

2

1

3

4

5

Table 1-8 Indicator description of devices with single power modules


1 Powerindicator

PWR Off The device is poweredoff.

Green The primary powersupply of the device isnormal.



1-15


Amber The device is poweredby the RPS powermodule. The main powersupply is faulty.

2 RPUindicator

RPS Off The device is notconnected to the RPSpower module or theRPS power module isfaulty.

Green The device is connectedto the RPS powermodule.



Green The system runsabnormally or is beingstarted.

Amber The indicator performsself-check at startup.


Red The system runsabnormally after thedevice is registered; orabnormality alarmsabout the power supply,fan, or temperature aregenerated.

4 Mode switchindicator

- Off The interface indicatorsare in the default mode,indicating the STATstatus of interfaces.

Green The interface indicatorstemporarily indicate theSpeed status ofinterfaces. The interfaceindicators restore thedefault mode (off) in 30s.


Quick Start


Issue 02 (2010-12-01)


Red The interface indicatorstemporarily indicate thestacking ID of thedevice. The interfaceindicators restore thedefault status (off) in30s.

As shown in Figure 1-6, No.5 shows the mode switch button. When you press the mode switchbutton for the first time, the mode indicator turns green and the interface indicators indicate theSpeed status of interfaces. When you press the mode switch button for the second time, the modeindicator turns red and the interface indicators indicate the Stack status of interfaces. When youpress the mode switch button for the third time, the mode indicator restores the default status,that is, Off. If you do not press the mode switch button for 30s, the mode indicator turns off.

Table 1-9 Indicator description of devices with dual power modules

Indicator Identifier Status Description

Power indicator PWR1 Off The power module is not inposition or the powersupply is abnormal duringthe configuration of thesingle power module.


Red The possible causes are asfollows:l The power module is in

position but the powerswitch is turned offduring theconfiguration of dualpower modules.

l The device is notconnected to the powermodule.

l The power module isfaulty.



1-17


Power indicator PWR2 Off The power supply moduleis not in position or thepower supply of the boardis abnormal during theconfiguration of the singlepower module on thedevice.


Red The possible causes are asfollows:l The power module is in

position but the powerswitch is turned offduring theconfiguration of dualpower modules.

l The device is notconnected to the powermodule.

l The power module isfaulty.

System operatingstatus indicator

SYS Off The system is not running.

Green The system runsabnormally or is beingstarted.

Amber The indicator performsself-check at startup.

Blinking green The system runs normally.

Red The system runsabnormally after the deviceis registered; orabnormality alarms aboutthe power supply, fan, ortemperature are generated.

Mode switchindicator

- Off The interface indicators arein the default mode,indicating the STAT statusof interfaces.


Quick Start


Issue 02 (2010-12-01)


Green The interface indicatorstemporarily indicate theSpeed status of interfaces.The interface indicatorsrestore the default mode(off) in 30s.

Red The interface indicatorstemporarily indicate thestacking ID of the device.The interface indicatorsrestore the default status(off) in 30s.












1-19


Green The device is a not a Masterswitch:l If the indicator of a certain

interface is solid green, itindicates that the number of theinterface is the stacking ID ofthe device and the device is nota Master switch.



interface is blinking green, itindicates that the number of theinterface is the stacking ID ofthe device and the device is aMaster switch.


Indicator Description of the S5300s Enabled with PoEThe following takes the S5328C-PWR-SI as an example to describe the indicators of the S5300senabled with PoE.

Figure 1-7 Schematic diagram of S5328C-PWR-SI indicators

1

35

2

4


Quick Start


Issue 02 (2010-12-01)

Table 1-11 Indicator description of S5300s enabled with PoE


1 Powerindicator

PWR1 Off The power module isnot in position or theboard power supply isabnormal during theconfiguration of thesingle power module.



module is inposition or but thepower switch isturned off duringthe configurationof dual powermodules.




2 Powerindicator

PWR2 Off The power module isnot in position or theboard power supply isabnormal during theconfiguration of thesingle power module.




1-21









Green The system runsabnormally or isbeing started.

Amber The indicatorperforms self-checkat startup.


Red The system runsabnormally after thedevice is registered;or abnormalityalarms about thepower supply, fan, ortemperature aregenerated.


Quick Start


Issue 02 (2010-12-01)


4 Modeindicator

- Off The interfaceindicators are in thedefault mode,indicating the STATstatus of interfaces.

Green The interfaceindicatorstemporarily indicatethe Speed status ofinterfaces. Theinterface indicatorsrestore the defaultmode (off) in 30s.

Amber The interfaceindicatorstemporarily indicatethe PoE status ofinterfaces. Theinterface indicatorsrestore the defaultmode (off) in 30s.

Red The interfaceindicatorstemporarily indicatethe Stack status ofinterfaces. Theinterface indicatorsrestore the defaultstatus (off) in 30s.

As shown in Figure 1-7, No.5 shows the mode switch button. On an S5300, you can press themode switching button to switch the display modes of interface indicators. The status of themode indicator represents the display mode of interface indicators. Take the S5328C-PWR-SIfor example. By default, the mode indicator is off and the interfaces are in the STAT status.When you press the mode switching button for the first time, the mode indicator turns green andthe interface indicators indicate the Speed status of interfaces. When you press the modeswitching button for the second time, the mode indicator turns amber and the interface indicatorsindicate the PoE status of interfaces. When you press the mode switching button for the thirdtime, the mode indicator turns red and the interface indicators indicates the Stack status ofinterfaces. When you press the mode switching button for the fourth time, the mode indicatorrestores the default status, that is, Off. If you do not press the mode switching button for 30s,the mode indicator turns off.

The following table shows the meanings represented by the status of interface indicators indifferent display modes.



1-23









PoE Off The interface has no remote powersupply.

Green The interface has remote powersupply.

Blinking green The possible causes are asfollows:l The power of the power-

receiving device exceeds theset threshold or the powersupply capacity of theinterface.


Green The device is a not a Masterswitch:l If the indicator of a certain

interface is solid green, itindicates that the number of theinterface is the stacking ID ofthe device and the device is nota Master switch.



Quick Start


Issue 02 (2010-12-01)



interface is blinking green, itindicates that the number of theinterface is the stacking ID ofthe device and the device is aMaster switch.


1.3 Device InstallationThis section describes how to install the S2300/S3300/S5300.

For details on device installation, see the S2300&3300&5300 Installation Quick Start.NOTE

You can obtain the paper documentation of the quick start from delivered accessories. To obtain the electronicdocumentation of the quick start, see 1.7 Obtaining Documentation.

1.4 Powering on the DeviceThis section describes the check items and the procedure for powering on and powering off thedevice.

1.4.1 Checking Before Power-onAfter hardware installation is complete, you need to check the device installation and cableinstallation.

1.4.2 Powering on the Device

1.4.3 Checking After Power-on

1.4.1 Checking Before Power-onAfter hardware installation is complete, you need to check the device installation and cableinstallation.

NOTE

Before power-on, you need to check the device cabinet, cables, connectors, sockets, labels, and on-siteenvironment.



1-25

Device Installation Checklist

CAUTIONBefore power-on, all the power distribution cabinets and power distribution frames must be off.

Table 1-13 describes the device installation checklist.

Table 1-13 Device installation checklist

No. Item Method

1 The cabinet is installed according to thedimensions on the design paper.

Check the cabinet according to theproject design document.

2 The expansion bolts for fixing thecabinet or base (support) to the groundare fastened. The plain washer, springwasher, and nut (bolt) are installedcorrectly.

-

3 The installation holes on the support andthe expansion bolts adapt to each otherto ensure insulation between the supportand the ground and between the floorbracket and the guide rail.

Use the multimeter to measure theresistance between the bolt and thegrounding bolt of the rack. Theresistance must be more than five megaohms.

4 The surfaces of the cabinets in the samerow should be on the same plane. Thecabinets are arranged closely and tidily.The cabinets on the sides of the mainpath are aligned. The position errorshould be less than 5 mm.

-


Quick Start


Issue 02 (2010-12-01)

No. Item Method

5 The accessories of the front and reardoors are completely installed and theconnection board is installed forcombining cabinets.

-

6 The front door of a cabinet can beopened and closed easily.

Open the door lock.

Close the door lock.

7 The card is installed and removedeasily. The screws on the panel shouldbe appropriately tightened and easilydisassembled. The spring wire is intact.

-

8 The cabinet surface must be tidy andclean; the components of the cabinetcannot be distorted; all identifiers arecorrect, clear, and complete.

-

9 The cabinet is kept clean and there areno excessive binding straps and otherarticles in the cabinet.

-

10 The ESD wrist straps are connected theESD jack in the chassis.



1-27

No. Item Method

11 Blank panels are installed in all emptyslots.

-

Cable Installation ChecklistTable 1-14 describes the cable installation checklist.

Table 1-14 Cable installation checklist

No. Item Method

1 The power cables and ground cables mustbe the copper wires and have no splice.The cables are safely connectedcomplying with standards.

-

2 The power cables and ground cables areconnected safely. The spring washer ofthe ground cable terminal is on the flatwasher.

-

3 The lugs of the power cables and groundcables are soldered or crimped tightly.

-

4 The power cables and ground cables arenot crossed and are separated from othercables.

5 The redundant part of the power cablesand ground cables should be cut. Thecables cannot be circled.

-

6 The ground cables must be tightlyconnected to the doors of the cabinet.

-

7 Labels are filled and attached to powercables and PGND cables; power cablesand PGND cables including powerdistribution switches are labeled correctlyand clearly. Labels are attached 20 mmfrom the connector.

-


Quick Start


Issue 02 (2010-12-01)

No. Item Method

8 The clearance between the power cable,PGND cable, and signal cable must bemore than 30 mm.

-

Table 1-15 describes the cabinet cable checklist.

Table 1-15 Cabinet cable checklist

No. Item Method

1 Cables are correctly connected. -

2 Cable ties are not overlapped andconnectors are smooth.

-

Table 1-16 describes the signal cable checklist.

Table 1-16 Signal cable checklist

No. Item Method

1 All the signal cables to be deployed passthe continuity check.

-

2 No signal cable is placed on the heatdissipation holes of the cabinet.

-

3 The bent part of a signal cable cannot betoo tight.

4 The cables in the cabinet cannot becrossed and the cables outside the cabinetare bound.

-



1-29

No. Item Method

5 The two ends of a signal cable are clearlyidentified by labels and the texts on thelabels are in the same direction.

-

6 The bolts that fix the cables are tightened. -

1.4.2 Powering on the Device

Turn on the power module of the device.

1.4.3 Checking After Power-on

Check the following items after the device is powered on:

l The sound of fan rotating can be heard and that the air exhaust from the air vents can befelt.

l The indicators of the power modules run normally. Normally, the INPUT and OUTPUTindicators are on.

l The indicators of the fan modules run normally. Normally, the STATUS indicator is onand the ALM indicator is off.

l Normally, the RUN indicator blinks and the ALM indicator is off.

1.5 Logging in to the DeviceThis section describes how to log in to the device.

1.5.1 Logging In to the Switch Through the Console Interface

1.5.2 Example for Configuring to Manage the SwitchThrough Telnet

1.5.3 Logging In to the Web System ClientBefore configuring the switch, you must log in to the Web system client.

1.5.1 Logging In to the Switch Through the Console Interface

ContextWhen establishing the configuration environment through the console interface, you can log into the S2300 through the HyperTerminal in Windows.

Procedure

Step 1 Start the HyperTerminal.

Choose Start > All Program > Accessories > Communications > HyperTerminal to start theHyperTerminal in Windows XP.


Quick Start


Issue 02 (2010-12-01)

Step 2 Set up a connection.

See Figure 1-8. Enter the name of the new connection in the Name text box and then chooseone icon. Then, click OK.

Figure 1-8 Setting up a connection

Step 3 Configure an interface for connection.

In the Connect To dialog box, as shown in Figure 1-9, select an interface from the drop-downlist box according to the actual interface on the PC or terminal. Next, click OK.

Figure 1-9 Configuring the interface for connection



1-31

Step 4 Set communication parameters.

When the COM1 Properties dialog box is displayed as shown in Figure 1-10, specify theparameters listed in Table 1-17.

NOTE

In other Windows operating systems, bits per second may be described as baud rate and data stream controlmay be described as traffic control.

Figure 1-10 Specifying parameters

Table 1-17 Parameters

Parameter Value

Bit per second (baud rate) 9600

Data bit 8

Parity check None

Stop bit 1

Flow control (traffic control) None


Quick Start


Issue 02 (2010-12-01)

Step 5 After the HyperTerminal starts, choose FileAttributes to display the COMM1 Propertiesdialog box, as shown in Figure 1-11. On the Setting tab, select VT100 in the Emulation drop-down list box. Click OK to complete the setting.

Figure 1-11 Selecting the terminal type

----End

Follow-up ProcedureAfter the preceding configurations are complete, press Enter. If the prompt <Quidway> isdisplayed on the screen, it indicates that the Command Line Interface (CLI) is displayed. In thiscase, you can enter commands to configure or manage the S2300. For details on configurationprocedures, see the following sections.

1.5.2 Example for Configuring to Manage the SwitchThroughTelnet

Networking RequirementsAs shown in Figure 1-12, SwitchA is newly added to the network. SwitchA and SwitchB areconnected through a trunk link. To enable the network administrator to manage SwitchAremotely, you need to configure the Telnet service and set the device name on SwitchA.



1-33

Figure 1-12 Networking diagram of managing SwitchA through Telnet

RS-232

Console cable

Console port

PC Switch A

serial port

Ethernetadministrator

Switch B

GE 0/0/1

GE 0/0/1

Configuration RoadmapThe configuration roadmap is as follows:l Log in to SwitchA through the console interface.l Set the device name.l Configure a management VLAN.l On SwitchA, set the type of the interface that connects SwitchA and SwitchB to trunk. Add

the interface to the management VLAN in trunk mode.l Configure the management IP address of SwitchA.l Configure the Telnet service.

Data PreparationTo complete the configuration, you need the following data:

l ID of the management VLANl Management IP address of SwitchAl Number of the interface that connects SwitchA and SwitchB on SwitchAl Authentication mode, user name, and password

Configuration Procedure1. Log in to SwitchA through the console port. For details, see Logging In to the Switch

Through the Console Interface.

2. Set the device name of SwitchA.<Quidway> system-view[Quidway] sysname SwitchA

3. Configure a management VLAN.[SwitchA] vlan 1


Quick Start


Issue 02 (2010-12-01)

[SwitchA-vlan1] description admin_VLAN

4. On SwitchA, set the type of the interface that connects SwitchA and SwitchB to trunk. Addthe interface to the management VLAN in trunk mode.[SwitchA] interface Gigabitethernet 0/0/1[SwitchA-GigabitEthernet0/0/1] undo port default vlan[SwitchA-GigabitEthernet0/0/1] port link-type trunk[SwitchA-GigabitEthernet0/0/1] port trunk allow-pass vlan 1[SwitchA-GigabitEthernet0/0/1] quit

5. Configure the management IP address of SwitchA.[SwitchA] interface vlanif 1[SwitchA-Vlanif1] ip address 10.10.10.10 255.255.255.0[SwitchA-Vlanif1] quit

6. Configure the Telnet service on SwitchA:l Set the authentication method to AAA, user name to huawei, and password to huawei.l Set the service type to telnet and user level to 15.l Configure AAA authentication for the users at the vty 0 to vty 4 levels.[SwitchA] aaa[SwitchA-aaa] local-user huawei password simple huawei[SwitchA-aaa] local-user huawei service-type telnet[SwitchA-aaa] local-user huawei level 15[SwitchA-aaa] quit[SwitchA] user-interface vty 0 4[SwitchA-ui-vty0-4] authentication-mode aaa [SwitchA-ui-vty0-4] return<SwitchA>

7. Verify the configuration.

NOTE

When the administrator logs in to SwitchA through Telnet, ensure that the PC of the administratorand SwitchA are reachable at the network layer.

<SwitchA> telnet 127.0.0.1Trying 127.0.0.1 ...Press CTRL+T to abortConnected to 127.0.0.1 ...************************************************************ All rights reserved (2005-2007) ** Without the owner's prior written consent, ** no decompiling or reverse-engineering shall be allowed. ** Notice: ** This is a private communication system. ** Unauthorized access or use may lead to prosecution. ************************************************************

Login authentication

Username:huaweiPassword:Note: The max number of VTY users is 15, and the current number of VTY users on line is 3. <SwitchA>

Configuration Filesl SwitchA

#sysname SwitchA#vlan batch 1



1-35

# vlan 1description admin_VLAN #interface Vlanif1ip address 10.10.10.10 255.255.255.0#interface GigabitEthernet0/0/1port link-type trunkport trunk allow-pass vlan 1#aaalocal-user huawei password simple huawei local-user huawei service-type telnet local-user huawei level 15 authentication-scheme default # authorization-scheme default # accounting-scheme default # domain default #user-interface con 0user-interface vty 0 4 authentication-mode aaa #return

1.5.3 Logging In to the Web System ClientBefore configuring the switch, you must log in to the Web system client.

Contextl Before logging in to the Web system client, ensure that the switch has been commissioned

and the Web system server is enabled.

NOTE

For operation procedures of enabling Web system server, refer to "Starting Web System" in theQuidway S2300 Series Ethernet Switches Configuration Guide - Basic Configuration.

l The Web system client connects to the switch through HTTP; therefore, you must log into the Web system client through HTTP.

l The Web system client supports the Microsoft Internet Explorer 6 (IE6) and Firefox 3.0,or later versions. The Web system client described in this document uses the IE6.

Procedure

Step 1 Open IE6.

Step 2 Enter the universal resource locator (URL) of the Web system client in the address bar and pressEnter. The User Login dialog box is displayed, as shown in Figure 1-13.

The URL is in the format http://IP/view/login.html, for example, http://10.164.19.131/view/login.html.


Quick Start


Issue 02 (2010-12-01)

Figure 1-13 Login

Step 3 Enter values in User Name, Password, and Verify Code.l The local switch provides a default account. The user name and password of the account are

admin.l To create, change, or delete user names and passwords, choose Security > AAA > User.l If your user level is 0, you can view only the Ping and Tracert pages after logging in to the

client.

Step 4 Choose a language, for example, English.l The Web system client of the current version supports Chinese and English.l After logging in to the client, you can select another language from the Language drop-down

list on the top right corner of the page.

Step 5 Click Login.

NOTE

If you select Save my password before clicking Login, you do not need to enter the password at nextlogin.

After you log in to the Web system, the main page is displayed. For details about the main page,see Window Layout.

----End

1.6 Service DeploymentThis section describes service deployment.

For details on service deployment, see the corresponding configuration guides.

1.7 Obtaining DocumentationCurrently, in addition to the documents delivered with the device, you can obtain thedocumentation in the following ways:



1-37

Methods of Obtaining Documentationl Logging in to the website http://support.huawei.com to retrieve and download the electronic

documentation, (recommended)l Contacting the local Huawei office to apply for the electronic documentation

Ways of Downloading DocumentationTo obtain the documents from the website http://support.huawei.com, you need to register onthe website and apply for the user name and password. Then, log in to the website by enteringthe user name and password applied, and click Documentation > Data Communication >Product > Ethernet Lanswitch > S23&33&53&CX200D Series to search, browse, anddownload the documents.


Quick Start


Issue 02 (2010-12-01)

Date post:	18-Apr-2015
Category:	Documents
Upload:	enggali
View:	296 times
Download:	0 times

Quick Start(V100R005 02)

Documents