8
FTTH ACCESS SOLUTION QUICKDR @W ®
FTTH ACCESS SOLUTION
QUICKDR@W®
QUICKDR@W®
Creating a network that can manage future demands and take rollout problems in its stride can be a challenge. The Prysmian QUICKDR@W® by JCS Technologies has been specially designed for this, enabling low cost incremental installation of the final customer drop.
QUICKDR@W® is a fast and effective pre-connectorised system for FTTH connections in mid- and low-density areas.
QUICKDR@W® is a complete system for the last mile, FTTH and campus networks encompassing the pre-connectorised fibre cable lead-in assembly, connectorised lead-in joint, and installation equipment
With ruggedised cable leads, provided with connectors at each section end, the final connection to the customer is achieved by plugging directly into fibre management products within the external network and at the customer premises.
The “plug and play” approach means that the final connection to the customer is achieved without the need for highly skilled operators or expensive equipment.
The fastest, easiest solution for customer network connection
FEATURES • Direct fibre broadband connection
• Pre-connectorised bidirectional WDM link
• Easily installed through long ducts
2 QUICKDR@W® FTTH ACCESS SOLUTION | JCS TECHNOLOGIES | JCSTECH.COM.AU
QUICKDR@W® LEAD-IN ASSEMBLY (LIA) – MK3
The QUICKDR@W® Lead-in Assembly (LIA) MK3 is a pre-connectorised cable that provides the means of rapidly connecting a customer to the network. The assembly is for use with the QUICKDR@W® Customer Lead in Joint (CLJ) MK3. The assembly comprises a QUICKDR@W® Pulling Shroud, QUICKDR@W® Lead-in Seal and QUICKDR@W® cable for rapid installation of the customer connection.
The QUICKDR@W® Pulling Shroud is used to feed a cable through a length of duct. The shroud protects the fibre and connector during installation and provides easy assembly and quick access to the connector after the pulling operation. During this operation a swivel should be used between the LIA and the pulling rope.
The QUICKDR@W® Lead-in Seal is used to connect the LIA to the Connectorised Lead-in Joint (CLJ). A transport sleeve is used to protect the connector before installation into the CLJ.
Suitable for single-fibre applications, the QUICKDR@W® Lead-in Assembly MK3 comes with one SC/APC type connector at each end.
FEATURES • Ultra low friction nylon sheath
design
• Smooth, quick duct installation, even if already occupied
• Long hauling lengths to 300m
• Termite resistant
• Low cost connection by one semi-skilled installer
• ABS connector shroud prevents water and dust ingress to IP67
• Shroud cord attachment pulling eye
• Bend limiting rubber strain relief boot protects fibre during installation
• Easily dismantled unit allows quick post installation access
• High performance SC/APC terminations
QUICKDR@W® FTTH ACCESS SOLUTION | JCS TECHNOLOGIES | JCSTECH.COM.AU 3
The QUICKDR@W® Lead-In Assembly MK3 is supplied on a cardboard reel inside a cardboard box.
QUICKDR@W® LIA SPECIFICATIONS
QUICKDR@W® LIA LOGISTICS
Cable
Maximium Installation Tension 500 N
Maximum Cable Diameter 5 mm
Dynamic Bend Diameter 180 mm
Static Bend Diameter 120 mm
Fibre Number / Type 1 / Singlemode
Connector Type SC/APC
Operating Temperature Range -20 to +70°C (5 to 95% RH}
Material
Shroud Casing ABS
Connector Boot Rubber
Lead-in Seal Glass Filled Polypropylene
Transport Sleeve Glass Filled Polypropylene
Testing
Sealing IP67
Optical 1310, 1550 and 1625nm
Dry Heat BS EN 60068-2-2Test Bb
Damp Heat IEC 60068-2-3: 1969
Change of Temperature IEC 60068-2-14: 1984
Vibration IEC 60068-2-6: 1995
Shock IEC 60068-2-27: 1987
Packed Dimensions (mm) 400L x 400W x 100D
Packed Weight
Length (m) Weight (kg) Length (m) Weight (kg)
25 1.40 175 5.90
35 1.70 200 6.65
50 2.15 225 7.40
75 2.90 250 8.15
100 3.65 275 8.90
125 4.40 300 9.65
150 5.15
CABLE LENGTHCONNECTOR TYPE
025 – 25m035 – 35m050 – 50m075 – 75m100 – 100m125 – 125m150 – 150m
SCA – SC/APCLCA – LC/APC
175 – 175m200 – 200m225 – 225m250 – 250m275 – 275m300 – 300m
F C Q – L I A - X X X - 0 0 1 - X X X
QUICKDR@W® LIA ORDERING SHIPPING
4 QUICKDR@W® FTTH ACCESS SOLUTION | JCS TECHNOLOGIES | JCSTECH.COM.AU
QUICKDR@W® CONNECTORIZED LEAD-IN JOINT (CLJ) – MK3
The QUICKDR@W® CLJ MK 3 is a purpose built customer access termination that allows the rapid and incremental activation of customer services utilising simple practices. The CLJ allows the plug in connection of up to 8 individual customer lead-in cables at the time of service activation. The CLJ is designed to be cascaded on a single distribution cable for optimised network design and can be used in all types of PON and PTP network configurations.
The customer lead-in cables are supplied for a single fibre connection with SC/APC connector fitted at both ends of the lead-in cable assembly.
FEATURES • Up to 8 pre-connectorised
QUICKDR@W LIAs can be installed into the lead-in seal ports
• Incremental customer connection enables deferred installation cost
• Following distribution phase CLJ installation by skilled installers, subsequent LIA connections need minimal training
• CLJ is supplied with SC adapters and pigtails preinstalled for single fibre applications
• CLJ can also be supplied with pre-installed connectorised passive splitters (1x4 or 1x8)
• Dedicated loose tube cable element storage area within the at the front of the closure
• Positive fibre management to 30mm bend radius
• Closure base contains one oval port, eight lead-in seal ports and two circular ports for spurs from the main cable loop
• Closure sealed to IP68
QUICKDR@W® FTTH ACCESS SOLUTION | JCS TECHNOLOGIES | JCSTECH.COM.AU 5
QUICKDR@W® CLJ SPECIFICATIONS
General
Number of Cable Ports 8 (Lead-in Seal), 1 (Oval), 2 (Circular)
Maximum Cable Diameter (mm) 7 (Lead-in Seal), 21 (Oval), 12 (Circular)
Maximum Splice Tray Capacity 1 (16 Fibres), 1 upgrade (additional 24)
Maximum Capacity 8 customer connection cables
Maximum Loop Capacity 48 (4 x 12 fibre elements)
Required Space Envelope (mm ) L300 x W 231 x D 164 (L 410 with heat shrink)
Operating Temperature Range -20 to +70 °C (5 to 95% RH)
Sealing IP68
Material
Cap Glass Filled Polypropylene
Base Glass Filled Polypropylene
Splice Tray FR HIPS
Testing
Closure Sealing IP68-AS60529-2004 IEC 60529 Ed 2.12001
Optical 1310, 1383, 1550 and 1625nm
Dry Heat BS EN 60068-2-2 Test Bb
Damp Heat IEC 60068-2-3:1969
Change of Temperature IEC 60068-2-14: 1984
Vibration IEC 60068-2-6: 1995
Shock IEC 60068-2-27: 1987
QUICKDR@W® CLJ LOGISTICS
Packing dimensions Packed Weight (kg) Net Weight (kg)
L 480 x W 250 x D 210 mm 2.4 1.9
F C Q - C L J - S C A - 0 0 1 - X X X
QUICKDR@W® CLJ ORDERING
The QUICKDR@W® Connectorised Lead-in Joint MK3 is supplied with a splice tray, connector patch panel, pigtails, oval port installation kit, splice protectors and a wall mounting bracket. Optional pre-installed 1x8 or 1x16 splitters are also available.
KIT CONTENTS
CONNECTOR TYPE CONFIGURATION
SCA – SC/APCLCA – LC/APC
008 – 8 Port1x4 – 1x4 Splitter1x8 – 1x8 Splitter
6 QUICKDR@W® FTTH ACCESS SOLUTION | JCS TECHNOLOGIES | JCSTECH.COM.AU
QUICKDR@W® ADDITIONAL ITEMS
The Compact Joint Support Tool allows the user to support a Compact Joint or CLJ within a portable workbench. The bracket is designed to fit most commercially available workbenches. It is dimensioned to enable a splicing machine to be placed on the workbench for close access to the splicing trays.
The CLJ MK3 Secondary splice tray can be used to upgrade the splicing capacity of the CLJ MK3. The splice tray can accommodate 24 fibre splices and is used in applications where a spur cable is required to be dropped from the primary looped cable.
The CLJ Cable Entry Kit is used to install an additional cable into one of the two circular ports. The kit comprises of a cable heat shrink, aluminium foil and a alcohol wipe.
SUPPORT TOOL
SECONDARY SPLICE TRAY
CLJ CABLE ENTRY KIT
JCS PART NO. – FCQ-CLJ-001-CST
JCS PART NO. – FCQ-CLJ-001-SST
JCS PART NO. – FCQ-CLJ-001-CEK
QUICKDR@W® FTTH ACCESS SOLUTION | JCS TECHNOLOGIES | JCSTECH.COM.AU 7
JCS TECHNOLOGIES PTY LTD | www.jcstech.com.au | U1, 5-11 Mellor Street, West Ryde NSW 2114T: +61 2 8878 6600 | F: +61 2 9808 2622 | E: [email protected]
00
76-0
62
016
LOCAL MANUFACTURE, SERVICE AND SUPPORT
