Radio Remote Controls
K-Series Radio Remote ControlsThe K-Series Radio Remote Controls are suitable for most standard overhead travelling crane applications. Phase Lock Loop (PPL) system creates distinct narrow band
operating frequencies, set by software. Units are C-Tick approved by the Australian Communications and Media Authority with 70 non-licensed operating channels
available on the 433-434MHz band. Units are also fully compliant with the requirements of AS1418.1-2002.
- Emergency Stop (EMS) is independently certifi ed EN-ISO 13849-1
Category 4 Safety of Machinery: Safety-related parts of control systems
- Transmitter EMS mushroom features 2 × N/C switches
- Receiver features dual independent CPUs (microcontrollers) which
monitor each other and will execute emergency stop if one CPU fails
- Receiver features dual series-connected main relays, each controlled
separately by 2 × different CPUs and will execute emergency stop‚
if one main relay fails
- Current sensing “jammed relay” detection on function relays
Extensive Safety Features
- 2-speed buttons with distinctive position detents
- Large mushroom E-Stop button (twist to reset)
- Integrated internal antenna
- Removable waterproof key
- 3 stage low power indicator (visual and audible)
- 4 × standard alkaline or rechargeable AA batteries
Transmitter Features
- Integrated horn / alarm built into receiver
- Visible external power indicator
- F-Type antenna for easy antenna extension
- Pre-wired with 2m loom multi-core cable
- Vibration dampening rubber bushing mounts
- 48 / 240 / 415V AC or 24V DC power supply
Receiver Features
Dual Frequencies: At start-up the radio control automatically selects frequency less likely to suffer interference
Adjustable Emission Power: Transmitter power can be adjusted (ie, lowered) as required for different applications and industry types (8 settings possible)
Remote Pairing: New transmitters (without data fi le) can be paired to an existing receiver without accessing the receiver installed on the crane
“Power On” Switch / Key: Non-contacting reed switch is also a removable key to disable transmitter
Temperature Stabilization: Temperature Control Crystal Oscillator (TXCO) prevents frequency deviation due to temperature changes
Changing Functions: Pushbutton functions and system settings are changed via PC software
Programmable Functions: Numerous possible non-standard functions include inching, acceleration delay, interlock delay, magnet control, etc.
Other Features of K-Series
K-Series Specifi cations
Operating Range: Minimum 100m
Frequency Range: 433.05 – 434.775MHz
70 channels with 25kHz channel spacing
Emission Power: Less than 10mW (adjustable, 8 levels)
ID Code: Over 1 million sets
Hamming Distance: ≥ 4
Enclosures: Glass fi bre reinforced nylon, IP65
EMS Stop EN-ISO 13849-1 Cat. 4
K2 Receiver Wiring Diagram
K2 Series
(1) AC-1
(2) AC-2
(3) MAIN-IN
(4) MAIN-OUT
(5) COM 1
(6) UP 1S
(7) UP 2S
(8) DOWN 1S
(9) DOWN 2S
COM 2 (10)
EAST 1S (11)
WEST 1S (12)
E/W 2S (13)
COM 3 (14)
SOUTH 1S (15)
NORTH 1S (16)
S/N 2S (17)
COM 4 (18)
AUX 1 (19)
AUX 2 (20)
AUX 2S (21)
COM 5 (22)
ALARM (23)
6.3A (F4)
6.3A (F5)
0.5A (F1)
6.3A (F2)
DB1
DB2
6.3A (F3)
RED
8-Button, 2-Speed with E-Stop
Kit Part Numbers:
- SAGA1-K2
AC Supply: 48 / 240 / 415V AC
- SAGA1-K2-24V DC
DC Supply: 24V DC
Kit consists of:
- 2 × Transmitters + 1 × Receiver
- 2 × Protective Pouches
- 8 × AA Alkaline Batteries
- Installation Manual
Transmitter Receiver
Part No. SAGA1-K2TX SAGA1-K2RX
Dimensions 167 × 48 × 55mm 167 × 154 × 88mm
Weight 210g 2100g
Power 4 × AA Batteries AC or DC supply
K4 Series
K4 Receiver Wiring Diagram
(1) AC-1
(2) AC-2
(3) MAIN-IN
(4) MAIN-OUT
(5) COM 1
(6) UP 1S
(7) UP 2S
(8) DOWN 1S
(9) DOWN 2S
(10) COM 2
(11) EAST 1S
(12) WEST 1S
(13) E/W 2S
COM 3 (14)
SOUTH 1S (15)
NORTH 1S (16)
S/N 2S (17)
COM 4 (18)
R1 (19)
R2 (20)
R1/2 2S (21)
R3 (22)
R4 (23)
R3/4 2S (24)
AUX 1 (25)
AUX 2 (26)
AUX 2S (27)
COM 5 (28)
SW A (29)
SW B (30)
0.5A (F1)
6.3A (F2)
6.3A (F3)
6.3A (F4)
RED
6.3A (F5)
12-Button, 2-Channel, 2-Speed with E-Stop
Kit Part Number:
- SAGA1-K4
AC Supply: 48 / 240 / 415V AC
Kit consists of:
- 2 × Transmitters + 1 × Receiver
- 8 × AA Alkaline Batteries
- Installation Manual
Transmitter Receiver
Part No. SAGA1-K4TX SAGA1-K4RX
Dimensions 274 × 77 × 42mm 310 × 160 × 95mm
Weight 385g 2900g
Power 4 × AA Batteries AC supply
K-Series Radio Remote Controls
The Protean-HT Radio Remote Control is ideal for controlling monorail hoists. Quartz crystals create distinct stable operating frequency. Unit is C-Tick approved by the
Australian Communications and Media Authority with 7 non-licensed operating channels on the 433-434MHz band.
Protean HT Radio Remote Controls
Protean HT
0.5 A
10 A
B
POWER 1WIRE COLOUR
BLACK
POWER 2 BROWN
COM (MAIN) RED
MAIN (COM) ORANGE
UP YELLOW
DOWN GREEN
EAST BLUE
WEST VIOLET
U/D 2S GREY
E/W 2S WHITE
RO/START PINK
Protean HT Wiring Diagram
4-Button, 2-Speed with E-Stop
Kit Part Numbers :
- 700PRO6DHT
AC Supply: 24 / 48V or 240 / 415V
- 700PRO6DHT-24VDC
DC Supply: 12 ~ 24V DC
Transmitter Receiver
Part No. 701PROL6B-TX 701PROL6B-RX
Dimensions 167 × 48 × 55mm 161 × 74 × 52mm
Weight 210g 2100g
Power 2 × AA Batteries AC or DC supply
Kit consists of:
- 2 × Transmitters + 1 × Receiver
- 2 × Protective Pouches
- 4 × AA Alkaline Batteries
- Installation Manual
Optional Accessories
Passive Antenna Protective Covers
© C
ondu
ctix
-Wam
pfl e
r | 2009 | s
ubje
ct t
o te
chni
cal m
odifi
catio
ns w
ithou
t pr
ior
notic
e Victoria (Head Offi ce)
14 England Street
Dandenong VIC 3175
Phone: +61 3 9706 8844
Fax: +61 3 9794 9298
New South Wales
4/77 Newton Road
Wetherill Park NSW 2164
Phone: +61 2 9604 9800
Fax: +61 2 9604 9844
Queensland
2/9 Archimedes Place
Murarrie QLD 4172
Phone: +61 7 3902 6000
Fax: +61 7 3902 6001
Western Australia
6/133 Kelvin Road
Maddington WA 6109
Phone: +61 8 9452 1986
Fax: +61 8 9459 0503
www.conductix.com
www.conductix.com
PUSH BUTTONPENDANTS ANDACCESSORIES
For the control of:
• Cranes
• Hoists
• Material handling
equipment
• Lift tables
• Transfer carswww.conductix.com.au
• Supplied fully assembled or in component form.
• Wide variety for easy customisation.
• Two to twelve buttons or up to twenty four
buttons in a duplex configuration.
• Compact safety yellow enclosure.
• High impact LEXAN polycarbonate or chemical
resistant XYLON enclosures.
• One, two and three speed switches.
• Neoprene booted buttons.
• Two-piece enclosure simplifies field wiring.
• Easy force and positive detent
switches/buttons.
Buttons:Neoprene booted buttons seal
out dirt and moisture. Available
in red, green and black.
Jumpers:Included with all
pre-assembled
pendants.
COB81P & COB81.5Ppistol grip pendants
Button legends:Standard button legends are included.
Vertical, selector and mushroom
legends are also available.
Fasteners:Self-captive stainless steel hardware
and threaded inserts in housing to
prevent thread stripping.
Cable bushings:Available in 8 sizes from
7.5mm to 29.5mm.
Bushing collar:Two sizes for cable
diameters from 7.5mm
to 29.5mm.
Hanger ring:For external strain relief
connection. ‘S’ hook is
available for strain relief
cable connection.
Enclosure:Ergonomic design, visible
safety yellow, shock and
vibration resistant, rugged
LEXAN polycarbonate or
XYLON. 2 through 12 button.
Regular or deep style.
Two-piece enclosure
simplifies field wiring.
Cable packing gland:Furnished with bushing and available
in 16 sizes. Insures water-tight seal.
Lamp and horn switch:Knock-out holes in 12mm dia.
and 19mm dia. are available for a
lamp and horn switch on 6
through 12 button enclosures.
• -15OC to 70O operation.
• UL listed and CSA approved.
• Contacts rated 5A at 120VAC & 3A at 240VAC.
• NEMA 4X (IP 56) enclosure rating.
• 100g shock resistance.
• Double insulated 2500V withstand voltage.
• Indoor or outdoor use.
FEATURES
Operation Appearance Wires✱✱ Part number(s) Contact arrangement
Pilot light small12mm. dia. hole
Colour: Red
(Voltage in parentheses)
1
35293 - (110VAC)36082 - (220VAC)36087 - (12VDC)34315 - (24VDC)
LED light ✱
Pilot light large19mm. dia. hole
Colour: Red
(Voltage in parentheses)
1
34316 - (110VAC)36083 - (220VAC)36088 - (12VDC)36081 - (24VDC)
Neon light ✱
Momentary push button
switch for horn 19mm. dia. hole
1 34312Resistive load ✱
125VAC 6A250VAC 3A
Pilot light
(Takes up onebutton space)
1
36042 - (24VDC)35181 - (12VDC)34303 - (110VAC)37581 - (220VAC)
Specify Light Colour= Red
G = GreenW = WhiteA = AmberB = Blue (DC only)
MaintainedON/OFF
1 3429234293
Momentary non-interlocking
2343083430934310
Dual pole momentary with
mechanical interlock
43432134322
Momentary single-speed
with mechanical interlock
2 3429434295
Momentary single button
1 3430534306
2343073711437199
✱ For use in6, 8, 10 and12 buttonenclosures
34292 34293
ON(Green)
OFF(Red)
ON(Green)
OFF(Red)
34308 34309 34310
34321 34322
34294 34295
34306
34307
37114
3719934305
Momentary 3 speed withmechanical & electrical
interlock
4 34323
✱✱ For reference only, quantity may vary depending on wiring method used.
SWITCHES
Operation Appearance Wires✱✱ Part number(s) Contact arrangement
2 positionkey switch
13711237115
2371163711737118
3 position key switch
2371193712037121
Variableposition resistor
2
34314B - (1K)34314D - (2K)34314 - (5K)
34314C - (10K)
Blank plate
0 34304 Blind rubber gasket with metal plate
37115 37116
37117 37118
37112
37119 37120
37121
Momentary 2 speed withmechanical
interlock
3342963429734298
34297
34298 – Same as 34297 but with delayed opening of contacts 7 & 8“Break- Before - Make” Contact Arrangement
34296
Maintained multi-position
selector switch (2 position and
3 position)
1 3710737108
2
343173431834319343203710937110
34317 34318 34319 34320
37107 37108 37109 37110
Push lock twist-releasemushroom
switch
13431337122
2371233712437125
34313 37123
37124
37125
37122
✱✱ For reference only, quantity may vary depending on wiring method used.
SWITCHES
Pendant cables:
Supplied with two
outer steel support
wires as required
by crane code
AS1418.1.
Pre-assembled festoon systems:
Choose a Conductix C-track, square track or beam festoon system and have
it completely pre-assembled and pre-wired with a pushbutton pendant.
Radio remote controls:
For the wireless control of
electrical equipment.
RELATED PRODUCTS
VICTORIA Head Office14 England Street, Dandenong, Victoria 3175, AustraliaTel: 61 3 9706 8844 Fax: 61 3 9794 9298 Email: [email protected]
NEW SOUTH WALES
4 / 77 Newton Road, Wetherill Park,New South Wales 2164, AustraliaTel: 61 2 9604 9800 Fax: 61 2 9604 9844 Email: [email protected]
QUEENSLAND
52 Lysaght Street, PO Box 6211, Acacia Ridge, Queensland 4110, Aust.Tel: 61 7 3219 6911 Fax: 61 7 3344 5377 Email: [email protected]
WESTERN AUSTRALIA
592 Albany Highway, Victoria Park,Western Australia 6100, AustraliaTel: 61 8 9355 2077 Fax: 61 8 9355 2088Email: [email protected]
TELFORD 1417