MOUNTING INSTRUCTIONS

RAY

MOUNTING

RAY Series fixtures ship with your choice of hanging hardware. To mount your RAY fixture, start

by identifying a suitable support structure to hang your fixture from. RAY22 weighs 1lb 4oz,

RAY44 weighs 2lb 3oz, and RAY66 weighs 3lbs 2oz. The power supply for all three RAY fixtures

weighs 2lbs 2oz. Common support structures used to hang RAY fixtures include Unistrut, trusses,

pipes and structural channel.

RAY STANDARD MOUNTING BRACKETS

Standard mounting brackets are designed to provide two points

of contact to hang from or hard mount to a support structure.

1 Start by installing the two

screws into the threaded holes

in the brackets

2 Insert the brackets into the channel windows on either end of the RAY fixture. Please

ensure the screw-heads remain above the channel when inserting brackets.

RAY SUSPENSION KIT

The RAY Suspension Kit allows you to suspend RAY up to 5’ below a suitable support structure and

control the angle at which the RAY fixture shines on your canopy.

1 Begin by threading the larger screws

through the holes on the long end of

the L-brackets.

2 Align L-brackets with the crimp-

brackets as show in the drawing

on the right and connect the two

brackets using the smaller screws.

Hand tighten screw to allow for

adjustments later.

3 Slide brackets into desired

position based on the support

structure you are mounting to

or hanging from. Ideal spacing

should equal the distance

from the center of the RAY

fixture. When bracket is in

desired position, hand-tighten

the screws on each bracket to

pin it in place.

4 Suspend your RAY fixture using the side-facing holes in the brackets, or hard-mount to a support

structure over your canopy. Bracket spacing can be easily adjusted after installation.

3

4

5

Insert the long end of the L-brackets into the channel windows on either end of the RAY fixture.

Ensure the screw-heads remains above the channels when inserting bracket. Once L-brackets are

inserted, hand tighten the screws above the channel to pin the bracket to the fixture.

Install the included suspension cables over a suitable support structure using the loops at the end

of each wire. Position loops the same distance apart as your fixture length to ensure stability, and

then attach carabiners to the end of each cable.

Insert the ferruled end of the included 8” crimping cable into the crimping bracket as pictured below.

6 Using a pair of pliers, crimp the sides of

the crimping bracket inward to trap the

crimping cable.

7 After both crimping cables have been

secured to the crimping brackets, suspend

your RAY fixture from your suspension

cables using the carabiners and the

looped end of the crimping cable.

8 Adjustments can be made to the deployment

angle at any time after install. To change

deployment angle, simply loosen the smaller

screw that binds the brackets together,

adjust the RAY deployment angle, and re-

tighten the small screw to lock fixture into

desired angle.

SUSPENSION EXTENSION KIT

Each RAY Suspension Extension Kit allow you to add one more RAY fixture to your RAY Suspension Kit.

Please note that a fully assembled RAY Suspension Kit is required for the Suspension Extension Kit to work.

1 Begin by threading the larger screws

through the holes on the long end of

the L-brackets.

2 Align L-brackets with the crimp-

brackets as show in the drawing

on the right and connect the two

brackets using the smaller screws.

Hand tighten screw to allow for

adjustments later.

3 Insert the long end of the L-brackets into the channel windows on either end of the RAY fixture.

Please ensure the screw-heads remains above the channels when inserting bracket. Once L-brackets

are inserted, hand tighten the screws above the channel to pin the bracket to the fixture.

4

5

6

When the brackets are fully assembled and attached to your RAY fixture, insert either end of the

double-crimp cable into the crimping bracket slot and pinch with a pair of pliers.

Insert the other end of the double-crimping

cable into the bottom slot of the crimping

bracket from your original RAY Suspension

Kit. Pinch to bottom of the crimping

bracket to lock and lower cable into place.

Adjustments can be made to the deployment angle at any time after install. To change

deployment angle, simply loosen the smaller screws that binds the brackets together, adjust

deployment angle, and re-tighten the small screws to lock fixture into desired orientation.

Minor adjustments may need to be made to the crimping brackets to ensure both fixtures are

deployed at the same angle.

512.212.4544 • fluence.science© Copyright 2018. Fluence Bioengineering, Inc.

Version 1.2 • 7.2018 • 70682A

Review our products, share your grow and stay abreast of the latest Fluence news and product releases through the channels below:

HOW TO APPLY YOUR VINYL-CUT FLUENCE STICKER

Clean and dry the surface where the sticker will be applied.

Remove backing sheet to expose adhesive and apply sticker to desired surface.

Starting from the center and working outward, squeegee pre-masked surface

with a credit card to remove air bubbles.

Allow adhesive to bond approximately 15 minutes before removing the back of the

sticker at a 45° angle, keeping it as close to the sticker as possible. If lettering is

coming up with back, re-squeegee before attempting to remove.

Last, and most important, please recycle all packaging material.

Future generations will thank you.

4

1

2

3