Apex Companies, LLC 8854 Rixlew Lane Manassas, VA 20109 T 703.396.6730 F 703.396.6743 apexcos.com September 18, 2014 Ms. Jennifer Spindle Stafford County Public Schools Department of Planning and Construction 31 Stafford Avenue Stafford, Virginia 22554 Re: Report for Asbestos Reinspection Garrisonville Elementary School and Wright Middle School 100 Wood Drive Stafford, VA 22556 Dear Ms. Spindle: Apex Companies, LLC (Apex) was contracted to perform an asbestos inspection at Garrisonville Elementary School and Wright Middle School addressed at 100 Wood Drive in Stafford, Virginia. Apex visited the schools on August 25 and 26, 2014 to perform the inspection and collect samples per Apex’s proposal dated August 11, 2014. 1.0 ASBESTOS INSPECTION Materials that were considered suspect asbestos containing (ACM) were identified, and the number of samples to be collected were determined using AHERA (40 Code of Federal Regulations (CFR) Part 763) protocols. As defined by AHERA policy, suspect materials include the following building material types: 1. Surfacing materials - including spray-applied fire proofing or trowel-applied wall and/or ceiling plaster; 2. Thermal System Insulation (TSI) - including tank insulation, pipe insulation, and mudded pipe elbows; and 3. Miscellaneous materials - including ceiling tile, floor tiles and mastics, gaskets (if accessible), fire doors, drywall (gypsum board) and joint (spackling) compound. Suspect ACMs that are homogeneous in nature (i.e., uniform in color and texture) were identified and touched to determine friability (ability to be reduced to powder by hand pressure), sampled by removing a small piece that was placed in a labeled sample bag, and given a specific identifier for reference, e.g. B-01. For a given homogeneous area, one or more samples were collected in a randomly distributed manner in accordance with AHERA provisions as referenced in the OSHA asbestos in construction standard [29 CFR 1926.1101]. Every reasonable attempt was made to locate ACM. However, areas that are inaccessible can only be addressed through extrapolation of conditions in accessible building space and review of building plans, specifications, or other building documents provided to Apex. Inaccessible is defined as areas of the building that could not be tested (sampled) without destruction of the structure or a portion of the structure. Changes in the condition of the site may occur with time due to either natural processes or human activities. The findings presented in this report are based on site conditions existing at the time
Transcript
Apex Companies, LLC 8854 Rixlew Lane Manassas, VA 20109 T 703.396.6730 F 703.396.6743 apexcos.com
September 18, 2014 Ms. Jennifer Spindle
Stafford County Public Schools
Department of Planning and Construction
31 Stafford Avenue
Stafford, Virginia 22554
Re: Report for Asbestos Reinspection Garrisonville Elementary School and Wright Middle School 100 Wood Drive
Stafford, VA 22556
Dear Ms. Spindle:
Apex Companies, LLC (Apex) was contracted to perform an asbestos inspection at Garrisonville Elementary School and Wright Middle School addressed at 100 Wood Drive in Stafford, Virginia. Apex visited the schools on August 25 and 26, 2014 to perform the inspection and collect samples per Apex’s proposal dated August 11, 2014. 1.0 ASBESTOS INSPECTION
Materials that were considered suspect asbestos containing (ACM) were identified, and the number of samples to be collected were determined using AHERA (40 Code of Federal Regulations (CFR) Part 763) protocols. As defined by AHERA policy, suspect materials include the following building material types:
1. Surfacing materials - including spray-applied fire proofing or trowel-applied wall and/or ceiling plaster;
2. Thermal System Insulation (TSI) - including tank insulation, pipe insulation, and mudded pipe elbows; and
3. Miscellaneous materials - including ceiling tile, floor tiles and mastics, gaskets (if accessible), fire doors, drywall (gypsum board) and joint (spackling) compound.
Suspect ACMs that are homogeneous in nature (i.e., uniform in color and texture) were identified and touched to determine friability (ability to be reduced to powder by hand pressure), sampled by removing a small piece that was placed in a labeled sample bag, and given a specific identifier for reference, e.g. B-01. For a given homogeneous area, one or more samples were collected in a randomly distributed manner in accordance with AHERA provisions as referenced in the OSHA asbestos in construction standard [29 CFR 1926.1101]. Every reasonable attempt was made to locate ACM. However, areas that are inaccessible can only be addressed through extrapolation of conditions in accessible building space and review of building plans, specifications, or other building documents provided to Apex. Inaccessible is defined as areas of the building that could not be tested (sampled) without destruction of the structure or a portion of the structure. Changes in the condition of the site may occur with time due to either natural processes or human activities. The findings presented in this report are based on site conditions existing at the time
Jennifer Spindle, Stafford County Public Schools September 18, 2014 Asbestos Inspection Report Page 2
of the inspection. Apex cannot be responsible for any errors or omissions in this assessment resulting from incomplete or inaccurate disclosures.
Apex collected a total of sixty three (63) samples from suspect ACM. All samples were sent to EMSL Analytical (EMSL), a National Voluntary Laboratory Accredited Program (NVLAP Certification No. 200293-0) accredited laboratory located in Beltsville, Maryland. A summary of the samples collected and laboratory results are presented in the table below. EMSL’s laboratory Certificate of Analysis and chain-of-custody documentation are presented in Appendix A. The standard for ACM is 1.0% by weight.
Table 1 – Summary of Suspect Asbestos Containing Materials Testing
Description of Material Type
Friable (Yes/No)
Location Sample
Numbers ACM
Estimated Quantity1,2
Miscellaneous Materials
FT-01, 12”x12”, White with gray streaks
No SRO B-01, B-03 NAD --
M-01, Mastic associated with FT-01
No SRO B-02, B-04 8%, 8%
Chrysotile 100 Sq. Ft.
FT-02, 12”x12”, Dark gray with streaks
No Bathroom in Main Office
B-05, B-07 NAD --
M-02, Mastic associated with FT-02
No Bathroom in Main Office
B-06, B-08 NAD --
FT-03, 12”x12”, Gray/blue with white
No
E28, E21, E20, E19, E18, E32,
E33, E4, 11A, F&CS,
B-09, B-11 NAD --
M-03, Mastic associated with FT-03
No
E28, E21, E20, E19, E18, E32,
E33, E4, 11A, F&CS,
B-10, B-12 NAD --
FT-04, 12”x12” gray with white streaks
No
Hallway from 11A- 14, Hallway
outside of Media Center
B-13, B-15 NAD --
M-04, Mastic associated with FT-04
No
Hallway from 11A- 14, Hallway
outside of Media Center
B-14, B-16 NAD --
FT-05, 12”x12”, Tan with brown
No
Storage closet adjacent to
11A, Hallway outside of
Media Center, S1, S3, F&CS closet, storage
closet in kitchen, E31, Gator dome
B-17, B-19 NAD --
Jennifer Spindle, Stafford County Public Schools September 18, 2014 Asbestos Inspection Report Page 3
Description of Material Type
Friable (Yes/No)
Location Sample
Numbers ACM
Estimated Quantity1,2
M-05, Mastic associated with FT-05
No
Storage closet adjacent to
11A, Hallway outside of
Media Center, S1, S3, F&CS closet, storage
closet in kitchen, E31, Gator dome
B-18, B-20 8%, 5%
Chrysotile 1000 Sq.
Ft.
FT-06, 12”x12”, Red with streaks
No Hallway
outside of Media Center
B-21, B-23 NAD --
M-06, Mastic associated with FT-06
No Hallway
outside of Media Center
B-22, B-24 NAD --
FT-07, 12”x12”, Blue with streaks
No
Computer room in Media
Center, hallway
outside of media center
computer room
B-25, B-27 NAD --
M-07, Mastic associated with FT-01
No
Computer room in Media
Center, hallway
outside of media center
computer room
B-26, B-28 NAD --
FT-08, 12”x12”, Yellow with streaks
No S5, S6, S7,
S8, hallway by S5-S8
B-29, B-31 NAD --
M-08, Mastic associated with FT-08
No S5, S6, S7,
S8, hallway by S5-S8
B-30, B-32 NAD --
FT-09, 12”x12”, Tan with streaks
No Office
adjacent to room 26
B-33, B-35 NAD --
M-09, Mastic associated with FT-01
No Office
adjacent to room 26
B-34, B-36 NAD --
FT-10, 12”x12”, White with blue
No
Storage closet 1 in Gym,
storage closet 2 in gym,
utility closet in gym,
throughout hallways in
Garrisonville ES
B-37, B-39 NAD --
Jennifer Spindle, Stafford County Public Schools September 18, 2014 Asbestos Inspection Report Page 4
Description of Material Type
Friable (Yes/No)
Location Sample
Numbers ACM
Estimated Quantity1,2
M-10, Mastic associated with FT-10
No
Storage closet 1 in Gym,
storage closet 2 in gym,
utility closet in gym,
throughout hallways in
Garrisonville ES
B-38, B-40 3%, 10%
CHrysotile 1000 Sq.
Ft.
FT-11, 12”x12”, Light green
No
Hallways throughout
Garrisonville ES.
B-41, B-43 NAD --
M-11, Mastic associated with FT-11
No
Hallways and classrooms Throughout Garrisonville
ES.
B-42, B-44 NAD --
FT-12, 12”x12”, Dark gray/blue
No
Hallways and classrooms throughout
Garrisonville ES.
B-45, B-47 NAD --
M-12, Mastic associated with FT-12
No
Hallways and classrooms throughout
Garrisonville ES.
B-46, B-48 NAD --
FT-13, 12”x12”, Pink
No
Hallways and classrooms Throughout Garrisonville
ES.
B-49, B-51 NAD --
M-13, Mastic associated with FT-13
No
Hallways and class rooms Throughout Garrisonville
ES.
B-50, B-52 NAD --
FT-14, 12”x12”, Dark green
No
Hallways and classrooms throughout
Garrisonville ES, Cafeteria
B-53, B-55 NAD --
M-14, Mastic associated with FT-14
No
Hallways and classrooms throughout
Garrisonville ES.
B-54, B-56 NAD --
Jennifer Spindle, Stafford County Public Schools September 18, 2014 Asbestos Inspection Report Page 5
Description of Material Type
Friable (Yes/No)
Location Sample
Numbers ACM
Estimated Quantity1,2
CT-01, 2’x2’, White, pinholes and channels, gray back
Yes
Main office, throughout A.G. Wright
MS and Garrisonville
ES classrooms
and hallways
B-57, B-58 NAD --
CT-02, 2’x2’, White, pinholes and pocks, gray back
Yes
Main office, throughout A.G. Wright
MS and Garrisonville
ES classrooms
and hallways
B-59, B-60 NAD --
CT-03, 4’x2’, White, pinholes and channels, gray back
Yes
Main office, throughout A.G. Wright
MS and Garrisonville
ES classrooms
and hallways
B-61, B-62 NAD --
CT-04, 4’x2’, White, pinholes, gray back
Yes
Main office, throughout A.G. Wright
MS and Garrisonville
ES classrooms
and hallways
B-63, B-64 NAD --
CB-01, Black cove base
No
Throughout hallways and classrooms of A.G. Wright
MS and Garrisonville
ES
B-65, B-67 NAD --
CBM-01, Cove base mastic
No
Throughout hallways and classrooms of A.G. Wright
MS and Garrisonville
ES
B-66, B-68 NAD --
CB-02, Gray cove base
No Media center,
offices in media center
B-69, B-71 NAD --
CBM-02, Cove base mastic
No Media center,
offices in media center
B-70, B-72 NAD --
CB-03, Tan cove base
No C1, C2, Media
Center, B-73, B-75 NAD --
CBM-03, Cove base mastic
No C1, C2, Media
Center, B-74, B-76 NAD --
Jennifer Spindle, Stafford County Public Schools September 18, 2014 Asbestos Inspection Report Page 6
Description of Material Type
Friable (Yes/No)
Location Sample
Numbers ACM
Estimated Quantity1,2
CB-04, Brown cove base
No In offices
adjacent to Tech Ed -1
B-77, B-79 NAD --
CBM-04, Cove base mastic
No In offices
adjacent to Tech Ed -1
B-78, B-80 NAD --
CM-01, Carpet mastic associated with blue carpet
No
Main office, Band Room
(A.G. Wright), E31, E17,
Media Center, Counseling hall rooms
1,2, computer lab
(Garrisonville)
B-81, B-82 NAD --
CM-02, Carpet mastic associated with red carpet
No Server room connected to main office
B-83, B-84 NAD --
CM-03, Carpet mastic associated with bright blue carpet
No
Principle Boatwright
office, closet connected to band room,
B-85, B-86 NAD --
CM-04, Carpet mastic associated with dark blue carpet
No
Rooms above main office, E7, E6, E3, conference
room (Garrisonville),
teacher’s lounge
(Garrisonville)
B-87, B-88 NAD --
CM-05, Carpet mastic associated with purple carpet
No Closet in room
across hall from 14
B-89, B-90 NAD --
CM-06, Carpet mastic associated with green carpet
No Room 22 B-91, B-92 NAD --
CM-07, Carpet mastic associated with burnt orange carpet
No Offices
connected to Tech Ed 2
B-93, B-94 NAD --
CM-08, Carpet mastic associated with gray carpet
No A.G. Wright Principal’s
Office B-95, B-96 NAD --
WC-01, Window caulk
No Throughout Buildings
B-97, B-98 NAD --
DW-01, Drywall Yes H1,
Counseling Hallway
B-99, B-100 NAD --
JC-01, Joint compound
No H1,
Counseling Hallway
B-101, B-102 NAD --
DM-01, Duct mastic No Rooms above
main office B-103, B-104 NAD --
Jennifer Spindle, Stafford County Public Schools September 18, 2014 Asbestos Inspection Report Page 7
Description of Material Type
Friable (Yes/No)
Location Sample
Numbers ACM
Estimated Quantity1,2
FD-01, Fire Doors Yes Throughout
school NA
Assumed Positive
20
Thermal System Insulation (TSI) Materials
F-01, Asbestos Pipe Fittings
Yes Piping
throughout the school
NA Assumed Positive
25
Surfacing Materials
No surfacing materials sampled 1 SF: square feet. 2 LF: linear feet. ND: Non-Detect. Note: these quantities are estimates only and not to be relied upon for Contractor bidding or proposal purposes, or for Notification requirements, Prospective abatement Contractor’s are solely responsible for determining actual quantities of ACMs and site conditions for pricing removal and developing work plans for ACM removal.
2.0 LIMITATIONS Although Apex attempted to survey all areas of the property, Apex makes no guarantees that hidden or inaccessible areas do not contain ACM. If however, suspect ACM is identified during any renovation or demolition activities, Apex recommends collecting additional samples. This report is based on Apex’s investigation of the subject premises on August 25 and 26, 2014. Apex’s findings and recommendations are based only on the services performed at the time of our site inspections. 3.0 CONCLUSIONS/RECOMMENDATIONS The mastics associated with FT-01, FT-05 and FT-10 are positive for asbestos. The pipe fittings (F-01) and fire doors (FD-01) located throughout the school are positive for assumed positive for asbestos. Apex is pleased to have been of service and if you have any questions regarding this report, please do not hesitate to contact us at (703) 396-6730. Sincerely, APEX COMPANIES, LLC
Matt Huber Project Manager Attachments Appendix A – Asbestos Laboratory Data Sheets and Executed Chains of Custody Appendix B – Photolog
APPENDIX A Asbestos Laboratory Data Sheets and Executed Chains of Custody
EMSL maintains liability limited to cost of analysis. This report relates only to the samples reported and may not be reproduced, except in full, without written approval by EMSL. EMSL bears no responsibility for sample collection activities or analytical method limitations. Interpretation and use of test results are the responsibility of the client. This report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST or any agency of the federal government. Non-friable organically bound materials present a problem matrix and therefore EMSL recommends gravimetric reduction prior to analysis. Samples received in good condition unless otherwise noted. Estimated accuracy, precision and uncertainty data available upon request. Unless requested by the client, building materials manufactured with multiple layers (i.e. linoleum, wallboard, etc.) are reported as a single sample. Reporting limit is 1%
Samples analyzed by EMSL Analytical, Inc. Kernersville, NC NVLAP Lab Code 102104-0, CA ELAP 2689, Virginia 3333-000228, West Virginia LT000321
EMSL maintains liability limited to cost of analysis. This report relates only to the samples reported and may not be reproduced, except in full, without written approval by EMSL. EMSL bears no responsibility for sample collection activities or analytical method limitations. Interpretation and use of test results are the responsibility of the client. This report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST or any agency of the federal government. Non-friable organically bound materials present a problem matrix and therefore EMSL recommends gravimetric reduction prior to analysis. Samples received in good condition unless otherwise noted. Estimated accuracy, precision and uncertainty data available upon request. Unless requested by the client, building materials manufactured with multiple layers (i.e. linoleum, wallboard, etc.) are reported as a single sample. Reporting limit is 1%
Samples analyzed by EMSL Analytical, Inc. Kernersville, NC NVLAP Lab Code 102104-0, CA ELAP 2689, Virginia 3333-000228, West Virginia LT000321
EMSL maintains liability limited to cost of analysis. This report relates only to the samples reported and may not be reproduced, except in full, without written approval by EMSL. EMSL bears no responsibility for sample collection activities or analytical method limitations. Interpretation and use of test results are the responsibility of the client. This report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST or any agency of the federal government. Non-friable organically bound materials present a problem matrix and therefore EMSL recommends gravimetric reduction prior to analysis. Samples received in good condition unless otherwise noted. Estimated accuracy, precision and uncertainty data available upon request. Unless requested by the client, building materials manufactured with multiple layers (i.e. linoleum, wallboard, etc.) are reported as a single sample. Reporting limit is 1%
Samples analyzed by EMSL Analytical, Inc. Kernersville, NC NVLAP Lab Code 102104-0, CA ELAP 2689, Virginia 3333-000228, West Virginia LT000321
EMSL maintains liability limited to cost of analysis. This report relates only to the samples reported and may not be reproduced, except in full, without written approval by EMSL. EMSL bears no responsibility for sample collection activities or analytical method limitations. Interpretation and use of test results are the responsibility of the client. This report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST or any agency of the federal government. Non-friable organically bound materials present a problem matrix and therefore EMSL recommends gravimetric reduction prior to analysis. Samples received in good condition unless otherwise noted. Estimated accuracy, precision and uncertainty data available upon request. Unless requested by the client, building materials manufactured with multiple layers (i.e. linoleum, wallboard, etc.) are reported as a single sample. Reporting limit is 1%
Samples analyzed by EMSL Analytical, Inc. Kernersville, NC NVLAP Lab Code 102104-0, CA ELAP 2689, Virginia 3333-000228, West Virginia LT000321
EMSL maintains liability limited to cost of analysis. This report relates only to the samples reported and may not be reproduced, except in full, without written approval by EMSL. EMSL bears no responsibility for sample collection activities or analytical method limitations. Interpretation and use of test results are the responsibility of the client. This report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST or any agency of the federal government. Non-friable organically bound materials present a problem matrix and therefore EMSL recommends gravimetric reduction prior to analysis. Samples received in good condition unless otherwise noted. Estimated accuracy, precision and uncertainty data available upon request. Unless requested by the client, building materials manufactured with multiple layers (i.e. linoleum, wallboard, etc.) are reported as a single sample. Reporting limit is 1%
Samples analyzed by EMSL Analytical, Inc. Kernersville, NC NVLAP Lab Code 102104-0, CA ELAP 2689, Virginia 3333-000228, West Virginia LT000321
EMSL maintains liability limited to cost of analysis. This report relates only to the samples reported and may not be reproduced, except in full, without written approval by EMSL. EMSL bears no responsibility for sample collection activities or analytical method limitations. Interpretation and use of test results are the responsibility of the client. This report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST or any agency of the federal government. Non-friable organically bound materials present a problem matrix and therefore EMSL recommends gravimetric reduction prior to analysis. Samples received in good condition unless otherwise noted. Estimated accuracy, precision and uncertainty data available upon request. Unless requested by the client, building materials manufactured with multiple layers (i.e. linoleum, wallboard, etc.) are reported as a single sample. Reporting limit is 1%
Samples analyzed by EMSL Analytical, Inc. Kernersville, NC NVLAP Lab Code 102104-0, CA ELAP 2689, Virginia 3333-000228, West Virginia LT000321
EMSL maintains liability limited to cost of analysis. This report relates only to the samples reported and may not be reproduced, except in full, without written approval by EMSL. EMSL bears no responsibility for sample collection activities or analytical method limitations. Interpretation and use of test results are the responsibility of the client. This report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST or any agency of the federal government. Non-friable organically bound materials present a problem matrix and therefore EMSL recommends gravimetric reduction prior to analysis. Samples received in good condition unless otherwise noted. Estimated accuracy, precision and uncertainty data available upon request. Unless requested by the client, building materials manufactured with multiple layers (i.e. linoleum, wallboard, etc.) are reported as a single sample. Reporting limit is 1%
Samples analyzed by EMSL Analytical, Inc. Kernersville, NC NVLAP Lab Code 102104-0, CA ELAP 2689, Virginia 3333-000228, West Virginia LT000321
EMSL maintains liability limited to cost of analysis. This report relates only to the samples reported and may not be reproduced, except in full, without written approval by EMSL. EMSL bears no responsibility for sample collection activities or analytical method limitations. Interpretation and use of test results are the responsibility of the client. This report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST or any agency of the federal government. Non-friable organically bound materials present a problem matrix and therefore EMSL recommends gravimetric reduction prior to analysis. Samples received in good condition unless otherwise noted. Estimated accuracy, precision and uncertainty data available upon request. Unless requested by the client, building materials manufactured with multiple layers (i.e. linoleum, wallboard, etc.) are reported as a single sample. Reporting limit is 1%
Samples analyzed by EMSL Analytical, Inc. Kernersville, NC NVLAP Lab Code 102104-0, CA ELAP 2689, Virginia 3333-000228, West Virginia LT000321
EMSL maintains liability limited to cost of analysis. This report relates only to the samples reported and may not be reproduced, except in full, without written approval by EMSL. EMSL bears no responsibility for sample collection activities or analytical method limitations. Interpretation and use of test results are the responsibility of the client. This report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST or any agency of the federal government. Non-friable organically bound materials present a problem matrix and therefore EMSL recommends gravimetric reduction prior to analysis. Samples received in good condition unless otherwise noted. Estimated accuracy, precision and uncertainty data available upon request. Unless requested by the client, building materials manufactured with multiple layers (i.e. linoleum, wallboard, etc.) are reported as a single sample. Reporting limit is 1%
Samples analyzed by EMSL Analytical, Inc. Kernersville, NC NVLAP Lab Code 102104-0, CA ELAP 2689, Virginia 3333-000228, West Virginia LT000321
EMSL maintains liability limited to cost of analysis. This report relates only to the samples reported and may not be reproduced, except in full, without written approval by EMSL. EMSL bears no responsibility for sample collection activities or analytical method limitations. Interpretation and use of test results are the responsibility of the client. This report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST or any agency of the federal government. Non-friable organically bound materials present a problem matrix and therefore EMSL recommends gravimetric reduction prior to analysis. Samples received in good condition unless otherwise noted. Estimated accuracy, precision and uncertainty data available upon request. Unless requested by the client, building materials manufactured with multiple layers (i.e. linoleum, wallboard, etc.) are reported as a single sample. Reporting limit is 1%
Samples analyzed by EMSL Analytical, Inc. Kernersville, NC NVLAP Lab Code 102104-0, CA ELAP 2689, Virginia 3333-000228, West Virginia LT000321
EMSL maintains liability limited to cost of analysis. This report relates only to the samples reported and may not be reproduced, except in full, without written approval by EMSL. EMSL bears no responsibility for sample collection activities or analytical method limitations. Interpretation and use of test results are the responsibility of the client. This report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST or any agency of the federal government. Non-friable organically bound materials present a problem matrix and therefore EMSL recommends gravimetric reduction prior to analysis. Samples received in good condition unless otherwise noted. Estimated accuracy, precision and uncertainty data available upon request. Unless requested by the client, building materials manufactured with multiple layers (i.e. linoleum, wallboard, etc.) are reported as a single sample. Reporting limit is 1%
Samples analyzed by EMSL Analytical, Inc. Kernersville, NC NVLAP Lab Code 102104-0, CA ELAP 2689, Virginia 3333-000228, West Virginia LT000321
EMSL maintains liability limited to cost of analysis. This report relates only to the samples reported and may not be reproduced, except in full, without written approval by EMSL. EMSL bears no responsibility for sample collection activities or analytical method limitations. Interpretation and use of test results are the responsibility of the client. This report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST or any agency of the federal government. Non-friable organically bound materials present a problem matrix and therefore EMSL recommends gravimetric reduction prior to analysis. Samples received in good condition unless otherwise noted. Estimated accuracy, precision and uncertainty data available upon request. Unless requested by the client, building materials manufactured with multiple layers (i.e. linoleum, wallboard, etc.) are reported as a single sample. Reporting limit is 1%
Samples analyzed by EMSL Analytical, Inc. Kernersville, NC NVLAP Lab Code 102104-0, CA ELAP 2689, Virginia 3333-000228, West Virginia LT000321
EMSL maintains liability limited to cost of analysis. This report relates only to the samples reported and may not be reproduced, except in full, without written approval by EMSL. EMSL bears no responsibility for sample collection activities or analytical method limitations. Interpretation and use of test results are the responsibility of the client. This report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST or any agency of the federal government. Non-friable organically bound materials present a problem matrix and therefore EMSL recommends gravimetric reduction prior to analysis. Samples received in good condition unless otherwise noted. Estimated accuracy, precision and uncertainty data available upon request. Unless requested by the client, building materials manufactured with multiple layers (i.e. linoleum, wallboard, etc.) are reported as a single sample. Reporting limit is 1%
Samples analyzed by EMSL Analytical, Inc. Kernersville, NC NVLAP Lab Code 102104-0, CA ELAP 2689, Virginia 3333-000228, West Virginia LT000321
Test Report: Asbestos Analysis of Bulk Materials via EPA 600/R-93/116 Method using
Polarized Light Microscopy
B-98
021404833-0098
WC-01 White None Detected
Non-Fibrous
Homogeneous
Cellulose<1% Non-fibrous (other)100%
B-99
021404833-0099
DW-01, Drywall Beige None Detected
Fibrous
Homogeneous
Cellulose2%
Glass2%
Non-fibrous (other)96%
B-100
021404833-0100
DW-01 Gray None Detected
Non-Fibrous
Homogeneous
Cellulose2%
Glass1%
Non-fibrous (other)97%
B-101
021404833-0101
JC-01, Joint
Compound
White None Detected
Non-Fibrous
Homogeneous
Cellulose<1% Ca Carbonate20%
Non-fibrous (other)80%
B-102
021404833-0102
JC-01 White None Detected
Non-Fibrous
Homogeneous
Ca Carbonate20%
Non-fibrous (other)80%
B-103
021404833-0103
DM-01, Duct
Mastic
Beige None Detected
Non-Fibrous
Homogeneous
Cellulose<1%
Synthetic<1%
Glass<1%
Non-fibrous (other)100%
B-104
021404833-0104
DM-01 White None Detected
Non-Fibrous
Homogeneous
Cellulose<1%
Synthetic<1%
Non-fibrous (other)100%
14THIS IS THE LAST PAGE OF THE REPORT.Test Report PLM-7.28.9 Printed: 8/29/2014 5:27:08 PM
Stephen Bennett, Laboratory Manager
or other approved signatory
Analyst(s)
EMSL maintains liability limited to cost of analysis. This report relates only to the samples reported and may not be reproduced, except in full, without written approval by EMSL. EMSL bears no responsibility for sample collection activities or analytical method limitations. Interpretation and use of test results are the responsibility of the client. This report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST or any agency of the federal government. Non-friable organically bound materials present a problem matrix and therefore EMSL recommends gravimetric reduction prior to analysis. Samples received in good condition unless otherwise noted. Estimated accuracy, precision and uncertainty data available upon request. Unless requested by the client, building materials manufactured with multiple layers (i.e. linoleum, wallboard, etc.) are reported as a single sample. Reporting limit is 1%
Samples analyzed by EMSL Analytical, Inc. Kernersville, NC NVLAP Lab Code 102104-0, CA ELAP 2689, Virginia 3333-000228, West Virginia LT000321
