1 DTMTOI01EN - v2 AUTOMATIC DOOR WITH VISIO OPERATOR - MAINTENANCE MANUAL Maintenance Manual AUTOMATIC SLIDING DOOR with VISIO Op. TRANSLATED DOCUMENT Read this instruction manual before use. In this manual you will find all the necessary information for the correct maintenance of the product. Keep this manual in a safe place for later referral. 1. MAINTENANCE INTERVALS There are two types of maintenance intervals: 2.1.– By TIME LAPSED: T 2.2.– By NUMBER OF CYCLES: C 0 4 7 8 3 1.1 TIME INTERVALS T-1 EVERY 6 MONTHS Cleaning of trolleys and rollers: Use a cloth lightly dampened. Rollers test: The rollers should rotate freely. Check the tightness of the rollers, and readjust if necessary. This manual contains instructions for the maintenance of manusa automatic door Visio model: NOTES: – All maintenance operations, except funcional tests, should be carried out in “open door” mode and with the power supply disconnected. The outside key switch should not be handled in these operations, as the engine could be trigerred by the fail- safe battery mechanism. – If the power supply cable is damaged, it should be replaced by a special cable or kit supplied by the manufacturer or by the post-sale service. – The drive unit must be disconnected from the power supply before removing the batteries. The batteries must be destroyed safely. Detection elements test: Check there are no dead angles near the sliding leaves. Check that the detectors are correctly fixed. T1-A B T1 A T1 C T1
Transcript
1
DTMTOI01EN - v2 AUTOMATIC DOOR WITH VISIO OPERATOR - MAINTENANCE MANUAL
Maintenance Manual
AUTOMATIC SLIDING DOOR with VISIO Op.
TRANSLATED DOCUMENT
Read this instruction manual before use. In this manual you will find all the necessary information for the correct maintenance of the product. Keep this manual in a safe place for later referral.
1. MAINTENANCE INTERVALS
There are two types of maintenance intervals:
2.1.– By TIME LAPSED: T 2.2.– By NUMBER OF CYCLES: C 0 4 7 8 3
1.1 TIME INTERVALS
T-1 EVERY 6 MONTHS
Cleaning of trolleys and rollers: Use a cloth lightly dampened.
Rollers test: The rollers should rotate freely. Check the tightness of the rollers, and readjust if necessary.
This manual contains instructions for the maintenance of manusa automatic door Visio model:
NOTES: – All maintenance operations, except funcional tests, should be carried out in “open door” mode and with the power supply disconnected. The outside key switch should not be handled in these operations, as the engine could be trigerred by the fail-safe battery mechanism. – If the power supply cable is damaged, it should be replaced by a special cable or kit supplied by the manufacturer or by the post-sale service. – The drive unit must be disconnected from the power supply before removing the batteries. The batteries must be destroyed safely.
Detection elements test: Check there are no dead angles near the sliding leaves. Check that the detectors are correctly fixed.
T1-A
B T1
A T1
C T1
2
DTMTOI01EN - v2 AUTOMATIC DOOR WITH VISIO OPERATOR - MAINTENANCE MANUAL
Photoelectric barrier test:
Trolley hanger lock test:
Panic break-out system test: Disconnect power supply and check that the electrical or intrinsic mechanical power panic break-out system’s leaves open. With panic break-out leaves, check that the force needed for their release is under 220N.
1.2 NUMBER OF CYCLES INTERVALS
C-1 EVERY 500.000 CYCLES 0 4 7 8 3
Replace the panic break-out guides.
T-2 EVERY 24 MONTHS
Change the brush strips and central sealing gaskets:
Replace fail-safe batteries: Disconnect the device from the power supply before removing the batteries. The batteries must be destroyed following safety procedures.
D T1
E T1
F T1
A T2
B T2
A C1 Replace the CO-48 elastic.
B C1
3
DTMTOI01EN - v2 AUTOMATIC DOOR WITH VISIO OPERATOR - MAINTENANCE MANUAL
Replace the guides on leaf-types T20, D20, E30, I30, D35 y S40.
Dismantle the motor group.
Dismantle and replace the motor release pistons.
Replace the belts and dragging arms.
Replace the rollers.
0 4 7 8 3
Replace the rubber end stops in the trolleys and lock.
C-2 EVERY 1.000.000 CYCLES
0 4 7 8 3
A C2
B C2
C C2
D C2
E C2
F C2
0 4 7 8 3
4
DTMTOI01EN - v2 AUTOMATIC DOOR WITH VISIO OPERATOR - MAINTENANCE MANUAL
C-3 EVERY 2.000.000 CYCLES
Replace roller profiles.
A C3
HEAD OFFICE Avda. Vía Augusta, 85-87 6th 08174 Sant Cugat del Vallés Barcelona - Spain Tel. +34 902 321 400 Fax +34 902 321 450 www.manusa.com
NOTE: The features included in this document are giv-en for information purposes only, and are not binding.
