RecoverPoint Specialist for Storage Administrators

EMC E20-575

Version Demo

Total Demo Questions: 10

Total Premium Questions: 66

Buy Premium PDF

https://dumpsboss.com

support@dumpsboss.com

DumpsBoss - Pass Your Next Certification Exam Fast!dumpsboss.com

QUESTION NO: 1

A RecoverPoint system has been deployed with XtremIO at production and disaster recovery sites. What is an accurate statement, if the replication mode for a Consistency Group has been set as “Continuous”?

A. Effective RPO will be 0 seconds

B. Set customized time between cycles

C. Effective RPO can be <60 seconds

D. Set minimum time between cycles

ANSWER: D

QUESTION NO: 2

In Unisphere for RecoverPoint, which wizard will allow an administrator to manage and monitor all correctly accessed copies undergoing testing, failover, and production recovery?

A. Protect Volumes

B. Test a Copy

C. Manage Protection

D. Manage Recovery

ANSWER: B

QUESTION NO: 3

A storage administrator is unable to perform Direct Access to a copy in their RecoverPoint environment. Which array type has this limitation with regards to RecoverPoint copies?

A. XtremIO

B. VMAX

C. VNX

D. VPLEX

ANSWER: A

DumpsBoss - Pass Your Next Certification Exam Fast!dumpsboss.com

QUESTION NO: 4

Which command can be used to reduce the impact of the initial volume synchronization on production applications?

A. config_io_throttling throttling=high

B. config_link_policy group= cgname copy_1=prod_copy copy_2= dr_copy regulate_application=yes

C. config_link_policy group= cgname copy_1=prod_copy copy_2= dr_copy regulate_application=no

D. config_io_throttling throttling=none

ANSWER: B

QUESTION NO: 5

When attempting to protect new XtremIO LUNs, the administrator is unable to add an XtremIO source LUN to the Consistency Group.

What is a possible reason for this issue?

A. XtremIO array was not licensed in RecoverPoint

B. RecoverPoint/EX only allows the protection of VNX arrays

C. XtremIO LUN was created with a 512-byte block size

D. XtremIO arrays are only protected with RecoverPoint for VMs.

ANSWER: A

QUESTION NO: 6

What describes RecoverPoint asynchronous replication write operations to the Journal volumes?

A. Journal is written to at three times the rate of the production volumes

B. Volumes of the same capacities will be concatenated and not striped

C. Writes to the Journal volume are typically small sequential writes

D. Writes to the Journal volume are typically large sequential writes

ANSWER: D

QUESTION NO: 7

Which RPA interface is used for management?

DumpsBoss - Pass Your Next Certification Exam Fast!dumpsboss.com

A. eth1

B. eth0

C. iSCSI-1

D. iSCSI-2

ANSWER: A

QUESTION NO: 8

In order to automatically provision Journal volumes, what does RecoverPoint require when this feature is sued?

A. Dedicated Resource Pools

B. Dedicated RecoverPoint Appliance

C. Consistency Group for each Journal volume

D. Total volume count must be less than 8, 000

ANSWER: A

QUESTION NO: 9

Which tools are listed under “System Analysis and Tools” selection of Unisphere for RecoverPoint?

A. Users and Security, Configure System Reports and Alerts, Collect System Information

B. Detect Bottlenecks, Balance Load, Configure System Reports and Alerts

C. Users and Security, Configure System Reports and Alerts, Change Security Level

D. Detect Bottlenecks, Balance Load, Collect System Information

ANSWER: D

QUESTION NO: 10

Which RecoverPoint CLI command can be used to show a summarization of the errors and warnings for either one site or the entire RecoverPoint system?

A. get_rpa_states

B. get_events_log

C. get_system_status

DumpsBoss - Pass Your Next Certification Exam Fast!dumpsboss.com

D. get_clusters_topology

ANSWER: B