RELOCATION MUNICIPAL COURT @ BCCH FIRST FLOOR...@ bcch first floor municipal court courthouse bcch...

G1.1

MACON, GEORGIA

DULOHERY WEEKS

CONSULTING ENGINEERS

G1.1 COVER SHEET

RELOCATION

@ BCCH FIRST FLOOR

MUNICIPAL COURT COURTHOUSEBCCH

SITE LOCATION MAPNO SCALE

INDEX OF DRAWINGS

& LOCATION MAPINDEX OF DRAWINGSCOVER SHEET,

A8.1

A2.1

A1.1

EX1.1

SECOND ST. MACON, GEORGIA

CORNER MULBERRY &

XII

III

XI

XIXV

III

VIIVI

I

II

V

IV

G1.2 GENERAL INFORMATION

BIBB COUNTY COURTHOUSE

PLUMBING, MECHANICAL & ELECTRICAL

FIRST FLOOR REFLECTED CEILING PLAN

FINISH & MATERIALS SCHEDULE, DOOR TYPES & DETAILS

FIRST FLOOR PLAN & LEGEND

EXISTING FIRST FLOOR PLAN

ARCHITECTURAL-4GENERAL - 2 PLUMBING - 3 MECHANICAL - 3 ELECTRICAL - 6

P2.1

P1.1

P0.1

PLUMBING PLAN

DEMOLITION PLAN

LEGEND AND SCHEDULES

M2.1

M1.1

M0.1

MECHANICAL PLAN

DEMOLITION PLAN


E5.1

E4.1

E3.1

E2.1

E1.1

E0.1

ELECTRICAL DETAILS

SYSTEMS ROUGH IN PLAN

POWER PLAN

LIGHTING PLAN

DEMOLITION PLAN


TOTAL NUMBER OF SHEETS = 19

FIRE PROTECTION - 1

F1.1 FIRE PROTECTION PLAN

PLANNERSARCHITECTS

2/15/2019

F:\

PR

OJ

EC

TS\18-025

Municip

al Co

urt

Relo

catio

n -

BC

CH 1st

Flo

or\

Workin

g

Dra

win

gs\18-025

G1.1 Co

ver

Sheet.d

gn

ISSUANCES

LIABILITY OF THE USER.

SOLE RISK AND

DRAWING IS AT THE

INFORMATION ON THIS

ANY USE OF THE

ANY FUTURE USE.

PROFESSIONAL FOR

OF THE DESIGN

REVIEW AND APPROVAL

DRAWING IMPLIES ANY

THE USE OF THIS

TO INDICATE THAT

ETC. ARE EXACT OR

DIMENSIONS, DETAILS,

ANYONE THAT ALL

OR GUARANTEE TO

EXPRESS WARRANTY

TO PROVIDE ANY

NOT BE CONSTRUED

DRAWING SHOULD

THE DELIVERY OF THIS

© COPYRIGHT 2018 BTBB inc.

NOT FOR REPRODUCTION

www.btbbinc.com

478.742.1208

Macon, GA 31201

609 Cherry Street

18-025

RE

LO

CA

TIO

N

@ B

CC

H FIR

ST F

LO

OR

MU

NICIP

AL C

OU

RT

CO

RN

ER M

UL

BE

RR

Y & S

EC

ON

D S

T. M

AC

ON,

GE

OR

GIA

11/26/18 CHECK SET

2/8/19 BID DOCUMENTS

ST

A

TE OF GE

O

RGIA

W. BROWN

ROBERT

RE

GISTERED ARCHI

TE

CTR

E

GISTERED ARCHI

TE

CT

CER

TIFICATE N

o. 7

129

MIN.

MIN.

2'-0" PREFERRED

1'-6" MIN.

CLEARANCES AT DOORSSTANDARD ADA MANEUVERING

XPULL SIDE PUSH SIDE

MIN.

X

PULL SIDE PUSH SIDEMIN.

Y

FRONT APPROACHES - SWINGING DOORS

MIN.

Y

HINGE SIDE APPROACHES - SWINGING DOORS

PULL SIDEPUSH SIDE

LATCH SIDE APPROACHES - SWINGING DOORS

2'-0" MIN.

X

Y

MIN.

Y

MIN.

STAIR HANDRAIL EXTENSIONS

OF ONE TREAD THAT IS REQUIRED AT EACH BOTTOM RISER.

Y IS THE MIN. HANDRAIL EXTENSION OF 1'-0" PLUS THE WIDTH

AT EACH TOP RISER.

NOTE: X IS THE 1'-0" MIN. HANDRAIL EXTENSION REQUIRED

ADA NOTES :

HC. HC.

WATER CLOSETS

CLEARANCES

FOUNTAINS

DRINKING

CLEARANCES

LAVATORY

9"

HANDRAIL

BOTTOM OF RUN

EXTENSION AT

TOP OF RUN

EXTENSION AT

MIN.

15"

DISPENSER

TOILET TISSUE

MIRROR

WATER PIPES

AND EXPOSED HOT

INSULATE TRAP

MIRRORDISPENSER

PAPER TOWEL

DISPENSER

SOAP

URINAL

2 RAILS ARE NOT USED

34" AT ALL LOCATIONS WHERE

ADULT HANDRAIL HT. SHALL BE

* NOTE:

AT OUT SWINGING DOORS

1'-6" AT IN SWINGING DOORS

SIGN

HANDLE

DOOR

SIGNAGE FIRE EXTINGUISHER

TO WALL

ON HANDRAIL

RETURN END

TO WALL

ON HANDRAIL

RETURN END

X

34"

MA

X.

38"

30"

4'-

0"

W/WALL MOUNTED WC

W/FLR MOUNTED WC

SPACE

FLOOR

CLEAR

DOOR LOCATION

ALTERNATE

MAX.4"

CLEARANCE

6" MAX. TOE

CLEARANCE

MIN. KNEE

AREA

IN SHADED

PERMITTED

EQUIPMENT

CLEARANCE

6" MAX. TOE

CLEARANCE

MIN. KNEE

17" TO 19"

34"

MA

X.

27"

MIN.

CL

EA

R

MIN.

DEPTH

MIN.

19"

MIN.

AD

UL

T

CHIL

DR

EN

14"-19

"

GRAB BARGRAB BAR

WATER CLOSET

1 1/4" TO 1 1/2"

MIN.

1'-0"

1'-0" MIN.

10" MAX.

DOORWAY

CLEAR

MINIMUM

LATCH.

A CLOSER AND A

DOOR HAS BOTH

NOTE X = 1'-0" IF X = 3'-6" MIN. IF Y = 4'-6"

NOTE X = 3'-0" MIN. IF Y = 5'-0"

LATCH.

A CLOSER AND A

IF DOOR HAS BOTH

NOTE Y = 4'-0" MIN.

IF DOOR HAS CLOSER.

NOTE Y = 4'-6" MIN.

IF DOOR HAS CLOSER .

NOTE Y = 4'-0" MIN.

2'-0" MIN.

X

OF L

AV.

OR SIN

K

34" T

O RIM

16"-18

"

16"-18

"

STANDARD WHEELCHAIR ACCESSIBLE STALLS

1'-5"

MIN.

1'-7"

MA

X.

MIN.

MIN.

MIN.

1/4"

MA

X

1/4" T

O 1/2"

1

2

MA

X.

1'-5" T

O

STANDARD ADA CLEARANCES

1/2"

MA

X

THRESHOLD

CLEARANCES

LAVATORY

CLEARANCES

FOUNTAINS

DRINKING CHANGE IN LEVEL

ACCESSIBLE ROUTE

DOOR THRESHOLDS

ACCESSIBLE ROUTE

SPACE

FLOOR

CLEAR

SPACE

FLOOR

CLEAR

1'-

7"

MIN.42" MIN.

12" MAX

36"

MIN.

32"

32"

W/ WALL MTD. WC

W/ FLOOR MTD. WC

3'-6"

32"

17"-19

"

35"-37"

42" MIN. 60" MIN.

COMPARTMENTACCESSIBLE TOILET STANDARD AMBULATORY

MIN.

TYPICAL ADA WHEELCHAIR REACH RANGES

GRAB BARS

BLOCKING FOR

PROVIDE SOLID

LIMITS: HIGH AND LOW

UNOBSTRUCTED FORWARD REACH

LIMITS: HIGH AND LOW

UNOBSTRUCTED SIDE REACH

GRAB BAR

18" VERTICAL

GRAB BAR

18" VERTICAL

AND BE SELF-CLOSING

DOOR MUST SWING-OUT

GRAB BAR

18" VERTICAL

CL

EA

R

MIN.

ONLY. OTHER APPROACHES = 4'-0" MIN.

MIN. LATCH APPROACH

DOOR

SELF-CLOSING

CLEAR

MIN.

CL

EA

R

MIN.

48"

MA

X

15"

48"

48"

1 1/

2"

Y

TREAD

38"

60

"

1'-0"

48"

17"

MA

X.

8"

9"

MIN.

8"

17"

40

"

MA

X.

AD

UL

T

29"

MIN.

27"

MIN.

40

"

MA

X.

34"

48"

2'-

10"

18"

MIN.

39"-4

1"

1'-0" 3'-6"

39"-41"

33"-36"

MAX.

18"42"

1'-0"2'-0"

17"-19

"

16"-18"

TOILET PARTITION

TO WALL OR

7" - 9"

60

"

MIN.

56" MIN.36"

59" MIN.

4'-

0"

2'-6"

2'-

0"

2'-6"

4'-

0"

3'-

6"

4'-

0"

4'-6"

3'-

6"

2'-8" MIN.

5'-

0"

60

"

MIN.

54" MIN.

56" MIN.

59" MIN.

42" MIN.

"AMERICANS WITH DISABILITIES ACT".

ALL HANDICAPPED ACCESSORIES AND FIXTURES SHALL CONFORM TO THE 1.

2.

4.13.9

4.13.10

MEASURED TO THE LEADING EDGE OF THE DOOR.

SECONDS TO MOVE TO A POINT 3 IN FROM THE LATCH,

POSITION OF 70 DEGREES, THE DOOR WILL TAKE AT LEAST 3

OF THE CLOSER SHALL BE ADJUSTED SO THAT FROM AN OPEN

DOOR CLOSER. IF A DOOR HAS A CLOSER, THEN THE SWEEP PERIOD

4.13.11

MAY HOLD THE DOOR IN A CLOSED POSITION.

RETRACT LATCH BOLTS OR DISENGAGE OTHER DEVICES THAT

THESE FORCES DO NOT APPLY TO THE FORCE REQUIRED TO

4.15.3

FRONT EDGE OF THE FOUNTAIN.

BE POSITIONED SO THE FLOW OF WATER IS WITHIN 3" OF THE

FOUNTAIN WITH A ROUND OR OVAL BOWL, THE SPOUT MUST

UNDER THE FLOW OF WATER. ON AN ACCESSIBLE DRINKING

HIGH SO AS TO ALLOW THE INSERTION OF A CUP OR GLASS

THE SPOUT SHALL PROVIDE A FLOW OF WATER AT LEAST 4"

PARALLEL OR NEARLY PARLLEL TO THE FRONT OF THE UNIT.

SHALL DIRECT THE WATER FLOW IN A TRAJECTORY THAT IS

WATER COOLERS SHALL BE AT THE FRONT OF THE UNIT AND

SPOUT LOCATION. THE SPOUTS OF DRINKING FOUNTAINS AND

4.16.6

DO NOT PERMIT CONTINUOUS PAPER FLOW SHALL NOT BE USED.

THIS SHEET. DISPENSERS THAT CONTROL DELIVERY, OR THAT

WITHIN REACH, AS SHOWN ON WATER CLOSET DRAWING

DISPENSERS. TOILET PAPER DISPENSERS SHALL BE INSTALLED

4.17.5

REDUCED TO A MINIMUM OF 3'-6"

DOOR SIDE OF THE STALL AND ANY OBSTRUCTION MAY BE

THE LATCH SIDE OF THE STALL DOOR, CLEARANCE BETWEEN THE

SHALL COMPLY WITH 4.13. IF TOILET STALL APPROACH IS FROM

DOORS. TOILET STALL DOORS, INCLUDING DOOR HARDWARE,

4.18.3

WITH 2'-5" CLEARANCE BETWEEN THEM.

THE FRONT EDGE OF THE URINAL RIM MAY BE PROVIDED

ACCESSIBLE ROUTE SHIELDS THAT DO NOT EXTEND BEYOND

APPROACH. THIS CLEAR SPACE SHALL JOIN OR OVERLAP AN

SHALL BE PROVIDED IN FRONT OF URINALS TO ALLOW FORWARD

CLEAR FLOOR SPACE. A CLEAR FLOOR SPACE 2'-6" BY 4'-0"

4.19.4

BE NO SHARP OR ABRASIVE SURFACES UNDER LAVATORIES.

CONFIGURED TO PROTECT AGAINST CONTACT. THERE SHALL

UNDER LAVATORIES SHALL BE INSULATED OR OTHERWISE

EXPOSED PIPES AND SURFACES. HOT WATER AND DRAIN PIPES

4.27.4

2 1/4"

THE FOLLOWING NOTES FROM THE ADA GUIDELINES SHALL BE USED

ABOVE FINISHED FLOOR.

DOOR PASSAGE SHALL BE MOUNTED NO HIGHER THAN 4'-0"

USABLE FROM BOTH SIDES. HARDWARE REQUIRED FOR ACCESSIBLE

FULLY OPEN, OPERATING HARDWARE SHALL BE EXPOSED AND

HANDLES ARE ACCEPTABLE DESIGNS. WHEN SLIDING DOORS ARE

OPERATED MECHANISMS, PUSH-TYPE MECHANISMS, AND U-SHAPED

TIGHT GRASPING OR TWISTING OF THE WRIST TO OPERATE. LEVER -

THAT IS EASY TO GRASP WITH ONE HAND AND DOES NOT REQUIRE

OPERATING DEVICES ON ACCESSIBLE DOORS SHALL HAVE A SHAPE

DOOR HARDWARE. HANDLES, PULLS, LATCHES, LOCKS AND OTHER

(C) SLIDING OR FOLDING DOORS: 5 LBS.

(B) INTERIOR HINGED DOORS: 5 LBS.

(A) EXTERIOR HINGED DOOR: (RESERVED).

(2) OTHER DOORS.

ALLOWABLE BY THE APPROPRIATE ADMINISTRATIVE AUTHORITY.

(1) FIRE DOORS SHALL HAVE THE MINIMUM OPENING FORCE

PULLING OPEN A DOOR SHALL BE AS FOLLOW:

DOOR OPENING FORCE. THE MAXIMUM FORCE FOR PUSHING AND

GREATER THAN 5 LBS.

FORCE REQUIRED TO ACTIVATE CONTROLS SHALL BE NO

GRASPING, PINCHING, OR TWISTING OF THE WRIST. THE

OPERABLE WITH ONE HAND AND SHALL NOT REQUIRE TIGHT

OPERATION. CONTROLS AND OPERATING MECHANISMS SHALL BE

INFORMATIONGENERAL

G1.2

PLANNERSARCHITECTS

2/15/2019

F:\

PR

OJ

EC

TS\18-025

Municip

al Co

urt

Relo

catio

n -

BC

CH 1st

Flo

or\

Workin

g

Dra

win

gs\18-025

G1.2

Ge

neral Inf

or

matio

n.d

gn

ISSUANCES


SOLE RISK AND

DRAWING IS AT THE

INFORMATION ON THIS

ANY USE OF THE

ANY FUTURE USE.

PROFESSIONAL FOR

OF THE DESIGN

REVIEW AND APPROVAL

DRAWING IMPLIES ANY

THE USE OF THIS

TO INDICATE THAT

ETC. ARE EXACT OR


ANYONE THAT ALL

OR GUARANTEE TO

EXPRESS WARRANTY

TO PROVIDE ANY

NOT BE CONSTRUED

DRAWING SHOULD




www.btbbinc.com

478.742.1208

Macon, GA 31201

609 Cherry Street

18-025

RE

LO

CA

TIO

N

@ B

CC

H FIR

ST F

LO

OR

MU

NICIP

AL C

OU

RT

CO

RN

ER M

UL

BE

RR

Y & S

EC

ON

D S

T. M

AC

ON,

GE

OR

GIA

11/26/18 CHECK SET


ST

A

TE OF GE

O

RGIA

W. BROWN

ROBERT

RE

GISTERED ARCHI

TE

CTR

E

GISTERED ARCHI

TE

CT

CER

TIFICATE N

o. 7

129

VAULT

BREAK

CORRIDOR

CORRIDOR

OFFICE

HV

AC

SNACK BAR

OFFICE

OFFICE

TL.

TL.

TL.

TL.

OFFICE

OFFICE

OFFICE

ELEV. ELEV. ELEV.

ELEV.

MECHANICAL

CORRIDOR

CORRIDOR

VAULT

CIVIL COURT

SHERIFF OF

COURTROOM

CIVIL & MAGISTRATE

CLERK

COURT

MAGIST.

CIVIL &

CL.

RAMP DN.

RAMP UP

H/C H/C

OFFICE

JAN.

RECEPTION

GENERAL OFFICE

OFFICE

GENERAL

OFFICE

GENERAL

RECEPTION /

TOILET

TOILET

CLO.

BREAK

BREAK

HV

AC

STAIR

STAIR

EXISTING FIRST FLOOR PLAN

MAIL ROOM

EX1.1

EXISTING CONDITIONSFIRST FLOOR PLAN -

1/8"=1'-0"

UP

UP

UP

UP

UP

UP

DN.

UP

UP

UP

DN.

UP

UP

UP

DN.

PLANNERSARCHITECTS

2/15/2019

F:\

PR

OJ

EC

TS\18-025

Municip

al Co

urt

Relo

catio

n -

BC

CH 1st

Flo

or\

Workin

g

Dra

win

gs\18-025

EX1.1 Fir

st

Flo

or

Pla

n

Existin

g

Co

nditio

ns - Phase

1.dgn

ISSUANCES


SOLE RISK AND

DRAWING IS AT THE

INFORMATION ON THIS

ANY USE OF THE

ANY FUTURE USE.

PROFESSIONAL FOR

OF THE DESIGN

REVIEW AND APPROVAL

DRAWING IMPLIES ANY

THE USE OF THIS

TO INDICATE THAT

ETC. ARE EXACT OR


ANYONE THAT ALL

OR GUARANTEE TO

EXPRESS WARRANTY

TO PROVIDE ANY

NOT BE CONSTRUED

DRAWING SHOULD




www.btbbinc.com

478.742.1208

Macon, GA 31201

609 Cherry Street

18-025

RE

LO

CA

TIO

N

@ B

CC

H FIR

ST F

LO

OR

MU

NICIP

AL C

OU

RT

CO

RN

ER M

UL

BE

RR

Y & S

EC

ON

D S

T. M

AC

ON,

GE

OR

GIA

11/26/18 CHECK SET


ST

A

TE OF GE

O

RGIA

W. BROWN

ROBERT

RE

GISTERED ARCHI

TE

CTR

E

GISTERED ARCHI

TE

CT

CER

TIFICATE N

o. 7

129

3 5/8 "

5/8 "

3 5/8 "

1'-2 5/8 "

4'-7"

2 1/2 "

4'-7";

2 1/2 "

4'-7"

1'-1

1/2 "

2'-

4"

GRAPHIC SCALE IN FEET

0 10 201 / 8" = 1'-0"

VAULT

BREAK

HV

AC

SNACK BAR

TL.

TL.

ELEV.

MECHANICAL

VAULT

CL.

UPUP

ELEV.

UP

UP

UP

UP

UP

UP

UP

DN.

UP

UP

UP

UP

RAMP DN.RAMP DN.

RAMP DN.

RA

MP

DN.

UP

MECH.

ST

AIR

STAIR

STAIR STAIR

DN.

RAMP UP

TOIL.

UPRAMP DN.

RAMP UP

H/C H/C

ST

AIR

RA

MP

UP

JAN.

UP

TEL.

UP

DN.

UP

DIRECTOR

ASSISTANT

PROPERTIES

DIRECTOR

ASSISTANT

CUSTODIAL

ASSISTANT

ADMINISTRATOR

CUSTODIAL

STAIR

STAIR

HV

AC

CHIEF CLERK

FILES

FILES

SUPPLY

COPY/

STATIONS

WORK

TL.

CHAMBERS

JUDGE'S

CLERK

DEPUTY

BAILIFF

BREAK

CLERK

DEPUTY

AIDE

PROBATION

PROBATION

WAITING

MECH.

CORRIDORCORRIDOR

STAIR

TL.

TL.

CL.

LOBBY

ELEV.

PRISONER

ELEV. ELEV.ELEV.

MECH.

- PHASES 1 & 2FIRST FLOOR PLAN

CL.

JUDGE'S SUITE

CLERK &

COURT

MUNICIPAL

CLERK

DEPUTY

WINDOW

VIEW

COUNTER

HEIGHT

ADA

FIRST FLOOR PLAN - MUNICIPAL COURT

OFFICE

OFFICE

OFFICE

GENERAL

RECEPTION /

OFFICE

GENERAL

STOR.

ALCOVE

MAIL ROOM

A1.1

LEGEND:

EXISTING WALLS TO REMAIN.

EXISTING DOOR TO REMAIN

5/8" GYP. BD. BOTH SIDES.

SOUND ATTENUATING BLANKETS AND

NEW 3 5/8" STEEL STUDS @ 16" o/c. w/

NEW DOOR101

ARE NOT IN CONTRACT.

NOTE: FURNISHINGS AND WORK STATIONS

BUILT-IN AND FURNISHINGS IN CONTRACT.

B

EX

EXEX

EX

EX

EX

EX

EXEX

EX EX

EX

EX

EX

EX

EX

EX

EX

EX

EX

101A

102

EX

A

103B

104A

105A

EX101

104

105

106107

108

109

114

113

112

111

115

116

117

118

119

120

121

122123 102

5/8 "

3 5/8 "

1 5/8 "

3 5/8 "

13'-

11 1/

8 "

3 5/8 "

8'-

2 7/8 "

3 5/8 "

VW2

VW1

103VW2

MUNICIPAL COURTROOM

REF.

UNFINISHED SIDE

6

A2.1

TOILETWOMEN

TOILETMEN

DOOR

EXISTING

RESWING

6

A2.1

CL.

CLERK

M.

106A

IT

126

8'-

0 5/8 "

3 5/8 "

127

LOBBY

WALL @ WINDOWS

REMOVE FALSE

WALL @ WINDOWS

REMOVE FALSE

BENCH TO REMAIN

EXISTING JUDGES

TO REMAIN

EXISTING PEWS

FE 1

FE 1

CORNER TO CORNER

NOTE: PAINT EXISTING WALLS

FE 1 FIRE EXTINGUISHER TYPE 1

ROD

NOTE: NEW CLOSET

PLANNERSARCHITECTS

2/15/2019

F:\

PR

OJ

EC

TS\18-025

Municip

al Co

urt

Relo

catio

n -

BC

CH 1st

Flo

or\

Workin

g

Dra

win

gs\18-025

A1.1 Fir

st

Flo

or

Pla

n - Phase

1.dgn

ISSUANCES


SOLE RISK AND

DRAWING IS AT THE

INFORMATION ON THIS

ANY USE OF THE

ANY FUTURE USE.

PROFESSIONAL FOR

OF THE DESIGN

REVIEW AND APPROVAL

DRAWING IMPLIES ANY

THE USE OF THIS

TO INDICATE THAT

ETC. ARE EXACT OR


ANYONE THAT ALL

OR GUARANTEE TO

EXPRESS WARRANTY

TO PROVIDE ANY

NOT BE CONSTRUED

DRAWING SHOULD




www.btbbinc.com

478.742.1208

Macon, GA 31201

609 Cherry Street

18-025

RE

LO

CA

TIO

N

@ B

CC

H FIR

ST F

LO

OR

MU

NICIP

AL C

OU

RT

CO

RN

ER M

UL

BE

RR

Y & S

EC

ON

D S

T. M

AC

ON,

GE

OR

GIA

11/26/18 CHECK SET


ST

A

TE OF GE

O

RGIA

W. BROWN

ROBERT

RE

GISTERED ARCHI

TE

CTR

E

GISTERED ARCHI

TE

CT

CER

TIFICATE N

o. 7

129

3'-0"

2"

2'-8"

2"

3'-0"

2"

2'-8"

2"

3'-

0"

1'-2"

3'-

0"

1'-8"

1'-4"

4"

3" TYP.

3'-0"

3 EQ. DOORS

3'-0"

3 EQ. DOORS

20'-2";

18'-0"

EA. SIDE

5/8" GYP. BD. -

FRAME

HOLLOW METAL

EA. SIDE

5/8" GYP. BD. -

FRAME

HOLLOW METALJAMB ANCHORS

MTL. ANCHORS

HEAD

JAMB3A

3B

1 1 / 2' = 1'-0"

1 1 / 2' = 1'-0"

2 x 4 PLATE

BASE

MATCH EX.

1 1/2" = 1' - 0"

A2.1

A2.1

& PASS-THRU

SPEAK HOLE

A2.1

DBL. STUD JAMB

CAULK BOTH SIDES

@ 16" O/C.

STEEL STUDS

@ 16" O/C.

STEEL STUDS

CAULK BOTH SIDES

3 5/8"

2"

5 7/8"

2"

3B

3A

A2.1

A2.1

A

7'-

0"

2"

7'-

2"

2" 3'-0" 2"

3'-4"

1 / 4" = 1'-0"

DOOR & FRAME TYPES

VW1

A2.1

3'-

0"

4'-

2"

A2.1

1 / 4" = 1'-0"

SYSTEM ALUMINUM STOREFRONT

VIEW WINDOW TYPES

VW2

2"

3'-

10"

2"

2" 3'-8" 2"

4'-0"

SYSTEM STOREFRONT ALUMINUM

HEAD

RUNNER

TRACK

EACH SIDE

5/8" GYP. BD.

A2.1

3 5/8"

TYPICAL

JAMB

DOUBLE STUD

EACH SIDE

5/8" GYP. BD.

SIDE, TYPICAL

CAULK EACH

A2.1

SILL

RUNNER TRACK

GYP. BD. EA. SIDE" TYPE "X"8

5

SIDE, TYPICAL

CAULK EACH

A2.1

A2.1

A2.1

CBCB

CBCB

CBCB

WD. TRIM

W/ 3/4"x1 1/2"

2-3/4" PLYWD.

BRACKET-

8"

A2.1

4C

SIDE

CAULK EA.

@ 16" O/C

STEEL STUDS

3 5/8"

SOUND BATTS

SOUND BATTS

SPACER

HEADER W/

6" STEEL STUD

W/ SPACER

HEADER

STUD

6" STEEL

SIDES

BOARD BOTH

5/8" GYPSUM

<WALL

METAL FRAMEWOOD DOOR IN HOLLOW 1 3/4" THK. FLUSH SOLID CORE

PAINT

PAINT

CLEAN PAINTPAINTEXISTING EXISTING


PAINTEXISTING



PAINTEXISTING

CLEAN PAINTPAINTWOODNEW & EX. AC. TILE FAC.

PAINTPAINTWOODNEW & EX. AC. TILE FAC.

GYP. BD.NEW & EX.

GYP. BD.NEW & EX.

CLEAN PAINTPAINTWOODNEW & EX.

GYP. BD.NEW & EX.

CLEAN PAINTWOODNEW & EX.

PAINT AC. TILE FAC.GYP. BD.NEW & EX.

CLEAN PAINTWOODNEW & EX. AC. TILE FAC.

PAINT AC. TILE FAC.GYP. BD.NEW & EX.

PAINTEXISTING

PAINTEXISTING

PAINT

PAINT


RES. TILE

CLEANWOODNEW & EX.PAINT

GYP. BD.NEW & EX.

PAINT

GYP. BD.NEW & EX.

PAINT

GYP. BD.NEW & EX.

PAINT

RES. TILE

FAC.

RES. TILE FAC.

FAC.

FAC.

FINISH & MATERIAL SCHEDULE RM.

No.ROOM NAME

FLOOR

MATERIAL FINISH

BASE WALLS CHAIRRAIL CROWN PICTURE MOULD CEILINGREMARKS

MATERIAL FINISH MATERIAL FINISH MATERIAL FINISH HEIGHT MATERIAL FINISH MATERIAL FINISH MATERIAL FINISH HEIGHT

101 WAITING

102 TOILET

103

PROBATION104

PROBATION AID105

DEPUTY CLERK106

TOILET107

108

109

CLOSET110

CLOSET111

TOILET112

JUDGE'S CHAMBERS113

DEPUTY CLERK114

DEPUTY CLERK115

WORKSTATIONS116

117

COPY / SUPPLY118

CHIEF CLERK119

FILES120

FILES121

BREAK122

ALCOVE

EXISTING

EXISTING EXISTING

RES. TILE

RES. TILE FAC.

FAC.

RES. TILE FAC.

RES. TILE FAC.

RES. TILE FAC.GYP. BD.NEW & EX.

AC. TILE FAC.

AC. TILE FAC.

AC. TILE FAC.

2'-

10"

4'-

2"

2"

3B

A2.1

B

7'-

0"

2"

7'-

2"

6'-2"

2"

3'-0"

2"

2'-8"

2"

3'-

0"

2"

w/ 1/4" TEMPERED GLASSMETAL FRAME & VIEW WINDOWWOOD DOOR IN HOLLOW 1 3/4" THK. FLUSH SOLID CORE

OVER 3/4" PLYWOOD

PLASTIC LAMINATE

2 x 4's @ 16" o/c.

PLATE

3 5/8" STL. STUD

@ 16" O/C

3 5/8" STL. STUDS

16" o/c.

2 x 4's @

OVER 3/4" PLYWOOD

PLASTIC LAMINATE

1

2

A2.1

1

WD. TRIM

W/ 3/4"x1 1/2"

2-3/4" PLYWD.

BRACKET-

PASS THRU WINDOW S

TYPICAL DETAILS @

2 x 4 PLATE

BASE

MATCH EX.

1 1/2" = 1' - 0"

A2.1 @ PASS-THRU

COUNTER DETAIL

WD. TRIM

W/ 3/4"x1 1/2"

2-3/4" PLYWD.

BRACKET-

8"

SIDES

BOARD BOTH

5/8" GYPSUM

<WALL

OVER 3/4" PLYWOOD

PLASTIC LAMINATE

2 x 4's @ 16" o/c.

PLATE

3 5/8" STL. STUD

@ 16" O/C

3 5/8" STL. STUDS

16" o/c.

2 x 4's @

OVER 3/4" PLYWOOD

PLASTIC LAMINATE

2

WD. TRIM

W/ 3/4"x1 1/2"

2-3/4" PLYWD.

BRACKET-

3'-

4"

3'-

8"

2"

3'-

4"

6"

@ ADA PASS-THRU

COUNTER DETAIL

EA. SIDE

5/8" GYP. BD. -

FRAME

HOLLOW METAL

EA. SIDE

5/8" GYP. BD. -

FRAME

HOLLOW METALJAMB ANCHORS

MTL. ANCHORS

HEAD

JAMB

BLANKETS, TYPICAL

SOUND ATTENUATING

A2.1

A2.1

DBL. STUD JAMB

CAULK BOTH SIDES

@ 16" O/C.

STEEL STUDS

@ 16" O/C.

STEEL STUDS

CAULK BOTH SIDES

2"

2"

SPACER

HEADER W/

6" STEEL STUD

4C

4A

5 7/8"(4 SIDES )

MTL. STOPS

1/2" x 1/2"

BLANKETS, TYPICAL

SOUND ATTENUATING

VIEW WINDOW DETAILS1 1 / 2' = 1'-0"

A2.1

3

A2.1

4

A2.1

5

5A

5B

5C

GLASS

1/4" TEMPERED

GLASS

1/4" TEMPERED

3A

3B

A2.1

A2.1

4A

4C

BLANKETS

SOUND ATTENUATING

BLANKETS

SOUND ATTENUATING

CLERKDEPUTY

WORKSTATIONS

PAINTPAINTEXISTING EXISTINGCLOSET

123

FAC. FACTORY

AC. TILE ACOUSTICAL TILE

EX. EXISTING

GYP. BD. GYPSUM BOARD

ABBREVIATIONS

RES. TILE RESILIENT TILE& BACK

1/2" WOOD SIDES

P.T. 2 X BLKG.

3/4" WD. TRIM

CAULK

METAL SLIDES

3/4" x 2 1/4" RAIL

1/4" PLYWD. BOTTOM

MEETING RAILWD. TRIM

3/4" X 1 1/2"

WD. TRIM

3/4" X 1 5/8"

1 1/2" = 1'- 0"

CABINET DETAIL

WALL & BASE

2'-1"

1'-1"

1 5/8"

4"

3"

3"

2'-0"

1'-4"

1'-0

"

WD. TRIM

3/4" X 2 1/2"

5/8" GYPSUM BOARD

2x4'S @ 16" O/C

BACK

1/4" PLYWD.

BACK

1/4" PLYWD.

SHOE MOULD

RB 127

A2.1

EDGEBAND

1/2" WD.

DRAWER W/

3/4" PLYWD.

EDGEBAND

1/2" WD.

DOOR W/

3/4" PLYWD.

EDGEBAND

1/2" WD.

SHELF W/

3/4" PLWD.

SIDES & ENDS

3/4" PLYWD. BOTTOM,

W/ 1/2" WD. EDGEBAND

3/4" PLYWOOD DOOR

SIDES & ENDS

3/4" PLYWOOD

EDGEBAND

1/2" WD.

SHELF W/

3/4" PLYWOOD

PLYWOOD

3/4"

7

3'-

0"

1'-2"

3'-

0"

N.I.C.

REF.

BREAK - SPACE No. 1221 / 4" = 1' - 0"

A2.1

7

A2.1

TYPES & DETAILSTYPES, VIEW WINDOWSCHEDULE, DOORFINISH & MATERIALS

RETURN @ WALL

EDGES & BACKSPLASH -

3/4" PLYWOOD TOP,

PLASTIC LAMINATE o/

MUNICIPAL COURTROOM

BASE

MATCH EX.

1 1/2" = 1' - 0"

2 x 4 PLATE

A2.1

LOW WALL DETAIL

3"

3"

@ 16" O/C

2x4 WD. STUDS

2

BOLT TO FLOOR

EACH STUD,

STEEL ANCHORS @

TRTD. 2X4 PLATE

A2.1

6

6MUNICIPAL COURTROOM SPACE No. 109

BOTH SIDES

5/8" GYP. BD. -

2 x 4 BETWEEN STUDS

2 x 4 BETWEEN STUDS

1 / 4" = 1' - 0"

FRAME

HOLLOW METAL

2"

GLASS

1/4" TEMPERED

JAMB

A2.1

4B

A2.1

4B

WD. TRIM

3/4" X 1 1/2"

PAINTWOOD BASE -

PAINTGYP. BD. -

PAINTGYP. BD. -

PAINTGYP. BD. -

PAINTGYP. BD. -

PAINTWOOD BASE -

PAINTGYP. BD. -

(4 SIDES )

MTL. STOPS

1/2" x 1/2"

(4 SIDES )

MTL. STOPS

1/2" x 1/2"

CLEAN

CLEAN

124 WOMEN TOILET EXISTING PAINTPAINTEXISTING EXISTING EXISTING

125 EXISTING PAINTPAINTEXISTING EXISTING EXISTINGMEN TOILET

CLEAN

CLEAN

PAINT

MATCH EXISTING -

WOOD BASE -

3 5/8"

CLERKCHIEF

COPY / SUPPLY

3A

A2.1MECHANICAL

CLERK

117CLERK

127LOBBY

117CLERK

127LOBBY

WOOD TRIM

o/ 3/4" x 2"

PLASTIC LAM.

WOOD TRIM

o/ 3/4" x 2"

PLASTIC LAM.

WOOD TRIM

o/ 3/4" x 2"

PLASTIC LAM.

PAINTPAINTRES. TILE FAC.WOODNEW & EX.

GYP. BD.NEW & EX.

AC. TILE FAC.126

PAINTLOBBYWOODNEW & EX.

GYP. BD.NEW & EX.127

IT

EXISTING CLEAN * *

4 SIDES

1/2" WOOD EDGEBAND -

3/4" PLYWOOD w/

- BOTH SIDES o/

PANEL MOULD

GATE - APPLIED

PAINTPAINTWOODNEW & EX.

GYP. BD.NEW & EX.

CLEAN

CL.

COURTROOM

CARPET 1

CARPET 2

CARPET 1

CARPET 1

CARPET 1

CARPET 1

CARPET 2

CARPET 1

RESILIENT FAC.

RESILIENT FAC

RESILIENT FAC

CARPET 1

RESILIENT FAC

RESILIENT FAC

RESILIENT FAC

RESILIENT FAC

RESILIENT FAC

CARPET 1

CARPET 1

CARPET 1

CARPET 1

CARPET 1

EXISTING REPLACE MISSING CEILING TILE

EXISTING

EXISTING

EXISTING

EXISTING

EXISTING

EXISTING

EXISTING

EXISTING REPAIR HOLES IN WALL

**

**

4B

EXISTING AS NOTED ON PLAN

- PAINT

- BOTH SIDES

PANEL MOULD

APPLIED

EXIS

TIN

G

MA

TC

H

MA

TC

H E

XIS

TIN

G

EXISTING

(STAIN ) - MATCH

NEW WOOD CAP

AC. TILE FAC.

AC. TILE FAC.

AC. TILE FAC.

AC. TILE FAC.

NOTE:

2'-

10"

6"

1'-2 1/2 "2'-2 1/2 "

1'-2 1/2 "2'-2 1/2 "

C.R. LAWRENCE # CRL ( ANODIZED )SPEAK HOLES EQUAL TOPASS THRU TRAY &

PASS THRU TRAY

PASS THRU TRAY

OPENING DETAILS

NEW DOOR

SIM. AT EXISTING WALL

PLANNERSARCHITECTS

2/15/2019

F:\

PR

OJ

EC

TS\18-025

Municip

al Co

urt

Relo

catio

n -

BC

CH 1st

Flo

or\

Workin

g

Dra

win

gs\18-025

A2.1 Finis

h

&

Materials

Sche

dule,

Do

or

Ty

pes

&

Details.d

gn

ISSUANCES


SOLE RISK AND

DRAWING IS AT THE

INFORMATION ON THIS

ANY USE OF THE

ANY FUTURE USE.

PROFESSIONAL FOR

OF THE DESIGN

REVIEW AND APPROVAL

DRAWING IMPLIES ANY

THE USE OF THIS

TO INDICATE THAT

ETC. ARE EXACT OR


ANYONE THAT ALL

OR GUARANTEE TO

EXPRESS WARRANTY

TO PROVIDE ANY

NOT BE CONSTRUED

DRAWING SHOULD




www.btbbinc.com

478.742.1208

Macon, GA 31201

609 Cherry Street

18-025

RE

LO

CA

TIO

N

@ B

CC

H FIR

ST F

LO

OR

MU

NICIP

AL C

OU

RT

CO

RN

ER M

UL

BE

RR

Y & S

EC

ON

D S

T. M

AC

ON,

GE

OR

GIA

11/26/18 CHECK SET


ST

A

TE OF GE

O

RGIA

W. BROWN

ROBERT

RE

GISTERED ARCHI

TE

CTR

E

GISTERED ARCHI

TE

CT

CER

TIFICATE N

o. 7

129

1 / 8" = 1'-0"

FIRST FLOOR REFLECTED CEILING PLAN - MUNICIPAL COURT

A8.1

PLANREFLECTED CEILINGFIRST FLOOR

NOTE:

AS IS.

GRID ARE TO REMAIN

NUMBERS WITHOUT CEILING

EXISTING SPACES WITH SPACE

GRAPHIC SCALE IN FEET

0 10 20

VAULT

BREAK

HV

AC

SNACK BAR

TL.

TL.

ELEV.

MECHANICAL

VAULT

CL.

UPUP

ELEV.

UP

UP

UP

UP

UP

UP

UP

DN.

UP

UP

UP

UP

RAMP DN.RAMP DN.

RAMP DN.

RA

MP

DN.

UP

MECH.

ST

AIR

STAIR

STAIR STAIR

DN.

RAMP UP

TOIL.

UPRAMP DN.

RAMP UP

ST

AIR

RA

MP

UP

JAN.

UP

TEL.

UP

DN.

UP

DIRECTOR

ASSISTANT

PROPERTIES

DIRECTOR

ASSISTANT

CUSTODIAL

ASSISTANT

ADMINISTRATOR

CUSTODIAL

STAIR

STAIR

HV

AC

CHIEF CLERK

FILES

FILES

SUPPLY

COPY/

STATIONS

WORK

TL.

CHAMBERS

JUDGE'S

CLERK

DEPUTY

BREAK

CLERK

DEPUTY

AIDE

PROBATION

PROBATION

WAITING

MECH.

CORRIDORCORRIDOR

STAIR

TL.

TL.

CL.

LOBBY

ELEV.

PRISONER

ELEV. ELEV.ELEV.

MECH.

CL.

JUDGE'S SUITE

CLERK &

COURT

MUNICIPAL

CLERK

DEPUTY

OFFICE

OFFICE

OFFICE

GENERAL

RECEPTION /

OFFICE

GENERAL

STOR.

ALCOVE

MAIL ROOM

A1.1

101

104

105

106107

108

109

114

113

112

111

115

116

117

118

119

120

121

122123 102

103

MUNICIPAL COURTROOM

REF.

TOILETWOMEN

TOILETMEN

CL.

CLERK

M.

IT

126

127

LOBBY

PLANNERSARCHITECTS

2/18/2019

F:\

PR

OJ

EC

TS\18-025

Municip

al Co

urt

Relo

catio

n -

BC

CH 1st

Flo

or\

Workin

g

Dra

win

gs\18-025

A8.1 Fir

st

Flo

or

Refle

cte

d

Ceilin

g

Pla

n - Phase

1.dgn

ISSUANCES


SOLE RISK AND

DRAWING IS AT THE

INFORMATION ON THIS

ANY USE OF THE

ANY FUTURE USE.

PROFESSIONAL FOR

OF THE DESIGN

REVIEW AND APPROVAL

DRAWING IMPLIES ANY

THE USE OF THIS

TO INDICATE THAT

ETC. ARE EXACT OR


ANYONE THAT ALL

OR GUARANTEE TO

EXPRESS WARRANTY

TO PROVIDE ANY

NOT BE CONSTRUED

DRAWING SHOULD




www.btbbinc.com

478.742.1208

Macon, GA 31201

609 Cherry Street

18-025

RE

LO

CA

TIO

N

@ B

CC

H FIR

ST F

LO

OR

MU

NICIP

AL C

OU

RT

CO

RN

ER M

UL

BE

RR

Y & S

EC

ON

D S

T. M

AC

ON,

GE

OR

GIA

11/26/18 CHECK SET


ST

A

TE OF GE

O

RGIA

W. BROWN

ROBERT

RE

GISTERED ARCHI

TE

CTR

E

GISTERED ARCHI

TE

CT

CER

TIFICATE N

o. 7

129

ABBREVIATION SYMBOL DESCRIPTION

HOT WATER RETURN PIPINGHWR

T

G

CA

HOT WATER PIPINGH

TEMPERED HOT WATER PIPINGT

COLD WATER PIPINGC

GAS PIPINGG

COMPRESSED AIR PIPINGCA

SOIL AND WASTE PIPINGS,W

VENT PIPINGV

SOLENOID VALVE

SHUT-OFF VALVE

SWING CHECK VALVE

FLOW CONTROL

CONNECT TO EXISTING

HOSE BIBB (WALL BOX) FREEZE PROOF

HOSE BIBB (WALL BOX) NON-FREEZE PROOFHB/B

HOSE BIBB (INTERIOR)HB/I

WALL CLEAN OUTWCO

ROOF DRAIN - TYPERD - ' '

FLOOR CLEAN OUTFCO

GRADE CLEAN OUT

FLOOR DRAIN - TYPE

WATER HAMMER ARRESTOR - SIZE

VENT THRU ROOF

PLUMBING LEGEND

HB/E

GCO

FD - ' '

HA - ' '

VTR

AFF

AFG

A/C

B/F

GPM

PSI

U/G

TYP.

T-P

H.C.

GPH

CONN.

ARCH.

PRESS.

W.C.

DWGS.

ABOVE FINISH FLOOR

ABOVE FINISH GRADE

ABOVE CEILING

BELOW FLOOR

GALLONS PER MINUTE

POUNDS PER SQUARE INCH

UNDER GROUND

TYPICAL

TRAP PRIMER

HANDICAP ACCESSIBLE

GALLONS PER HOUR

CONNECTION

ARCHITECTURAL

PRESSURE

WATER COLUMN

DRAWINGS

ST STORM DRAIN PIPING (BELOW GROUND)ST

OF OVERFLOW DRAIN PIPINGOF

ST STORM DRAIN PIPING (ABOVE GROUND)ST

VENT THRU SIDEWALLVTS

DOWNSPOUT NOZZLEDSN

ROOF HYDRANT NON-FREEZE PROOFHB/R

INSTANTANEOUS WATER HEATER SCHEDULE

ITEM FLOW RATETERMPERATURE

RISE POWERELECTRICAL

CHARACTERISTICS LOCATION REMARKS

IWH-1 1.5 GPM 38°F 8.3 kW SEE ELECTRICAL DWGS. UNDERLAVATORY

12" ±

FINISHED FLOOR

THREE WAY STOP

WALL FLANGE

3/4" COLD WATER SUPPLY (NOTE 1)

INSTANT WATER HEATER

1/2" COLD WATER TO SINK

1/2" HOT WATER TO SINK

---

1/2" COLD WATER TO HEATER

NOTES:

1. CONNECT 3/4" COLD WATER SUPPLY TO NEAREST COLD WATER PIPING SAME SIZE OR LARGER ABOVE CEILING.

RE

LO

CA

TIO

NM

UN

ICIP

AL

CO

UR

T

© COPYRIGHT 2018 BTBB inc.NOT FOR REPRODUCTION

609 Cherry StreetMacon, GA 31201 478.742.1208

www.btbbinc.com

THE DELIVERY OF THISDRAWING SHOULDNOT BE CONSTRUEDTO PROVIDE ANYEXPRESS WARRANTYOR GUARANTEE TOANYONE THAT ALLDIMENSIONS, DETAILS,ETC. ARE EXACT ORTO INDICATE THATTHE USE OF THISDRAWING IMPLIES ANYREVIEW AND APPROVALOF THE DESIGNPROFESSIONAL FORANY FUTURE USE.ANY USE OF THEINFORMATION ON THISDRAWING IS AT THESOLE RISK ANDLIABILITY OF THE USER.

ISSUANCES

18-025

PLANNERSARCH ITECTS

ARCHITECTS PLANNERS

CO

RN

ER

MU

LB

ER

RY

& S

EC

ON

D S

T.

MA

CO

N, G

EO

RG

IA@

BC

CH

FIR

ST

FLO

OR

P0.1

PLUMBING LEGEND& SCHEDULES

2.8.19 BID DOCUMENTS

GENERAL PLUMBING NOTES

1. ALL SITE UTILITIES ARE SHOWN IN APPROXIMATE LOCATIONS ONLY. VERIFYEXACT LOCATION AND INVERT ELEVATION IN FIELD BEFORE BEGINNING WORK.

2. ALL SUSPENDED PIPING SHALL BE SUPPORTED FROM FLOOR AND/OR ROOFSTRUCTURAL MEMBERS. IN NO CASE SHALL PIPING BE SUSPENDED FROMFLOOR OR ROOF DECK LESS THAN 4" THICK CONCRETE.

3. FIRE STOP ALL PENETRATIONS OF FIRE RATED ASSEMBLIES. REFER TOARCHITECTURAL DRAWINGS FOR ASSEMBLY RATINGS.

4. PIPING INSTALLED IN PLENUM SPACES SHALL MEET ASTM E-84, ASTM E-136 ANDUL 723 STANDARDS FOR FLAME SPREAD AND SMOKE GENERATION.COORDINATE PLENUM LOCATIONS WITH MECHANICAL CONTRACTOR.

5. COORDINATE ALL WORK WITH OTHER TRADES.

6. PROVIDE DRAIN VALVES AT ALL LOW POINTS IN ALL WATER PIPING SYSTEMS.

7. ALL WATER AND VENT PIPING SHALL BE INSTALLED ABOVE THE CEILINGUNLESS NOTED OTHERWISE.

8. ALL WASTE PIPING SHALL BE INSTALLED BELOW THE FLOOR UNLESS NOTEDOTHERWISE.

9. LOCATE ALL DRAINAGE PIPING AND CLEANOUTS CENTERED IN CORRIDORSUNLESS NOTED OTHERWISE. COORDINATE THE LOCATIONS OF CLEANOUTSWITH FLOOR PATTERN. ALL CLEANOUTS AT THE EXIT OF CORRIDORS SHALL BETWO-WAY CLEANOUTS.

10. ALL VENT TERMINALS SHALL BE LOCATED A MINIMUM OF 10 FEET FROM ANYDOOR, OPERABLE WINDOW, OR FRESH AIR INTAKE.

11. WHERE MOUNTING HEIGHTS OF FIXTURES CONFLICT WITH THE FIXTUREHEIGHTS ON THE ARCHITECTURAL DRAWINGS, THE HEIGHTS SHOWN ON THEARCHITECTURAL DRAWINGS SHALL TAKE PRECEDENCE.

PLUMBING FIXTURE SCHEDULE

ITEM DESCRIPTION

MINIMUM CONNECTION SIZE (INCHES)MOUNTING HEIGHT REMARKS

(ABOVE FLOOR)HOTWATER

COLDWATER

WASTE VENT

P-4 WORK SINK - H.C. 1/2" 1/2" 1-1/2" 1-1/2" COUNTERTOP

NOT TO SCALEP0.1

1 INSTANTANEOUS WATER HEATER DETAIL

T

PROFESSIONAL

NEER

IGNE

SIGER

ERED

No. 36592

IGROEG

A

E

A

A.BSA

MOH

T

L

NOTE 1

NOTE 1

NOTE 1

NOTE 1

DEMOLITION NOTES:

1. EXISTING PLUMBING FIXTURES SHALL REMAIN AND SHALL BE CLEANED / REFURBISHED AS PART OF NEW CONSTRUCTION WORK. CLEANING / REFURBISHMENT TO INCLUDE THE EXISTING FIXTURES AND ALL ASSOCIATED EXPOSED PIPING, FITTINGS, AND ACCESSORIES. DEFECTIVE FIXTURES, PIPES, FITTINGS, OR ACCESSORIES SHALL BE REPLACED TO MATCH THE EXISTING CONSTRUCTION AS NEEDED.

2. DEMOLISH ALL PLUMBING FIXTURES AND PIPING IN THE HATCHED REGION. CAP WATER, DRAINAGE AND VENT PIPING BELOW FLOOR, IN WALL OR ABOVE CEILING AS NEEDED FOR RENOVATION AND ABANDON.

3. NO RENOVATION WORK IN THIS AREA.

NOTE 2

NOTE 2

NOTE 3

NOTE 3

NOTE 3

RE

LO

CA

TIO

NM

UN

ICIP

AL

CO

UR

T



www.btbbinc.com


ISSUANCES

18-025

PLANNERSARCH ITECTS

ARCHITECTS PLANNERS

CO

RN

ER

MU

LB

ER

RY

& S

EC

ON

D S

T.

MA

CO

N, G

EO

RG

IA@

BC

CH

FIR

ST

FLO

OR

P1.1

PLUMBINGDEMOLITION PLAN


SCALE: 1/8" = 1'-0"P1.1

1 PLUMBING DEMO PLAN

T

PROFESSIONAL

NEER

IGNE

SIGER

ERED

No. 36592

IGROEG

A

E

A

A.BSA

MOH

T

L

DD

D

RAMP DN.

RAMP UP

K-2032GREENW

ICHLAVATO

RYVITREO

US CHINA

K-2032GREENWICH LAVATORY VITREOUS CHINA

DEPUTY CLERK

114

CL.

110

TL.

112

CL.

111

JUDGE'S CHAMBERS

113

CL.

108

TL.

107

PROBATION AIDE

105

PROBATION

104

DEPUTY CLERK

106

WAITING

101

CL.

103

TL.

102

MUNICIPALCOURTROOM

109

DEPUTY CLERK

115

WORK STATIONS

116

FRONT COUNTER

117

BREAK

122

FILES

121

FILES

120

CHIEF CLERK

119

COPY/SUPPLY

118

ALCOVE

123

SHEET NOTES:

1. EXISTING PLUMBING FIXTURES SHALL REMAIN AND SHALL BE CLEANED / REFURBISHED AS PART OF NEW CONSTRUCTION WORK. CLEANING / REFURBISHMENT TO INCLUDE THE EXISTING FIXTURES AND ALL ASSOCIATED EXPOSED PIPING, FITTINGS, AND ACCESSORIES. DEFECTIVE FIXTURES, PIPES, FITTINGS, OR ACCESSORIES SHALL BE REPLACED TO MATCH THE EXISTING CONSTRUCTION AS NEEDED.

2. 2"W, 1-1/2"V, 3/4"C. CONNECT TO NEAREST WASTE, VENT, AND DOMESTIC COLD WATER PIPING EQUAL TO OR LARGER IN SIZE.

3. NO RENOVATION WORK IN THIS AREA.

P-4

IWH-1/SEE 1 P0.1

NOTE 2

NOTE 3

NOTE 3

NOTE 3

NOTE 1

NOTE 1

NOTE 1NOTE 1

THIS ENCLOSED REGION IS TO INDICATE THE SCOPE OF THE RENOVATION WORK. ALL AREAS OUTSIDE OF THIS REGION SHALL REMAIN AS IS.

RE

LO

CA

TIO

NM

UN

ICIP

AL

CO

UR

T



www.btbbinc.com


ISSUANCES

18-025

PLANNERSARCH ITECTS

ARCHITECTS PLANNERS

CO

RN

ER

MU

LB

ER

RY

& S

EC

ON

D S

T.

MA

CO

N, G

EO

RG

IA@

BC

CH

FIR

ST

FLO

OR

P2.1

PLUMBING PLAN


SCALE: 1/8" = 1'-0"P2.1

1 PLUMBING PLAN

T

PROFESSIONAL

NEER

IGNE

SIGER

ERED

No. 36592

IGROEG

A

E

A

A.BSA

MOH

T

L

SUPPLY AIR DUCT

C1

ERV

AD

TD

DIA

OA

UG

W/

AFF

MECHANICAL LEGEND

T

Ø

RETURN AIR DUCT OR EXHAUST DUCT

DUCT TRANSITION

X=DIFFUSER TYPE / Y=THROW

Z=AIRFLOW, CFM

MANUAL DAMPER

FIRE DAMPER

SMOKE DAMPER

TURNING VANES

FLEXIBLE DUCT CONNECTION

THERMOSTAT/TEMPERATURE SENSOR

SPLIT SYSTEM AIR HANDLER

ENERGY RECOVERY VENTILATION UNIT

ACCESS DOOR

TRANSFER DUCT

DIAMETER

OUTSIDE AIR

UNDERGROUND

WITH

ABOVE FINISH FLOOR

XY

Z

SD

FD

MD

VARIABLE AIR VOLUME DAMPERVAVD

M

MOTORIZED DAMPER

M

CONNECT TO EXISTING

EXISTING NYLON CLAMPS (TYP)

EXISTING MANUAL DAMPERW/ 2" STANDOFF

EXISTING SUPPLY DUCTEXISTING EXHAUST DUCT

EXISTING NYLON CLAMPS(TYP)

PAINT INTERIORFLAT BLACK

EGGCRATE GRILLEMINIMUM6" HIGH PLENUM

PREINSULATEDFLEX. DUCT5 FT. MAX. LENGTH


EXISTING 45° DUCT TAKEOFF FITTING

EXISTING 45° DUCT TAKEOFF FITTING

DIFFUSER

EXISTING ROUND METAL DUCT

DUCT WRAP(TYP)

ROUND NECK EXTENSION

SHEET METAL 90° ELBOW

GLASSFAB AND MASTIC JOINT AROUND THROAT OF DIFFUSER

NOTES:1. INSTALL NYLON CLAMP ON FLEX DUCT INNER LINER AND ALSO ON OUTER JACKET.2. SEAL DUCT CONNECTIONS PER DUCT MANUFACTURER'S INSTALLATION INSTRUCTIONS.3. DIFFUSER INSULATION SHALL BE FULL SIZE OF GRID WITH SQUARE CORNERS, DO NOT COMPRESS INSULATION OR ALLOW AIR GAPS

BETWEEN INSULATION AND DIFFUSER. DO NOT TAPE INSULATION TO GRID. 4. USE FSK TAPE TO SECURE INSULATION AND BOTTOM EDGE OF DIFFUSER TO CEILING GRID. TRIM TAPE ON FACE OF DIFFUSER. TAPE

SHALL NOT BE EXPOSED AT CEILING GRID.5. WHERE ELBOW CONNECTION IS NOT POSSIBLE, PROVIDE ACCESSORY DIFFUSER ELBOW SUPPORT FOR FLEX DUCT CONNECTION AS

SPECIFIED.

MOLDED BACKPANINSULATION

PREINSULATED FLEX DUCT 5 FT MAX LENGTH


PAINT INTERIORFLAT BLACK

EGGCRATE GRILLEMINIMUM6" HIGH PLENUM

PREINSULATEDFLEX DUCT5 FT. MAX. LENGTH

EXISTING EXHAUST DUCT

DIFFUSER

PREINSULATEDFLEX. DUCT5 FT. MAX. LENGTH


EXISTING ROUND METAL DUCT


EXISTING SUPPLY DUCT

DUCT WRAP(TYP)

NOTES:1. INSTALL NYLON CLAMP ON FLEX DUCT INNER LINER AND ALSO ON OUTER JACKET.2. SEAL DUCT CONNECTIONS PER DUCT MANUFACTURER'S INSTALLATION INSTRUCTIONS.3. DIFFUSER INSULATION SHALL BE FULL SIZE OF GRID WITH SQUARE CORNERS, DO NOT COMPRESS INSULATION OR

ALLOW AIR GAPS BETWEEN INSULATION AND DIFFUSER. DO NOT TAPE INSULATION TO GRID. 4. USE FSK TAPE TO SECURE INSULATION AND BOTTOM EDGE OF DIFFUSER TO CEILING GRID. TRIM TAPE ON FACE OF

DIFFUSER. TAPE SHALL NOT BE EXPOSED AT CEILING GRID.5. WHERE ELBOW CONNECTION IS NOT POSSIBLE, PROVIDE ACCESSORY DIFFUSER ELBOW SUPPORT FOR FLEX DUCT

CONNECTION AS SPECIFIED.


EXISTING 90° SHOE TAP SADDLE DUCT FITTING

EXISTING 90° SHOE TAP SADDLE DUCT FITTING

ROUND NECK EXTENSION

SHEET METAL 90° ELBOW

GLASSFAB AND MASTIC JOINT AROUND THROAT OF DIFFUSER

MOLDED BACKPANINSULATION

DOORWAY

FLOOR

4' - 0" AFF UNLESS INDICATED OTHERWISE.

COORDINATE LOCATION WITH LIGHT SWITCHES, ETC. FOR SYMMETRY.

THERMOSTAT

AIR

FLO

W

SU

PP

LY

AIR

FLO

W

EX

HA

US

T / R

ET

UR

N

45°

L=1/4 W (6" MIN)

AIR FLOW

SUPPLY

AIR FLOW

EXHAUST / RETURN

RE

LO

CA

TIO

NM

UN

ICIP

AL

CO

UR

T



www.btbbinc.com


ISSUANCES

18-025

PLANNERSARCH ITECTS

ARCHITECTS PLANNERS

CO

RN

ER

MU

LB

ER

RY

& S

EC

ON

D S

T.

MA

CO

N, G

EO

RG

IA@

BC

CH

FIR

ST

FLO

OR

M0.1

MECHANICALLEGEND &SCHEDULES


GENERAL MECHANICAL NOTES

1. THE DRAWINGS SHOW THE GENERAL ARRANGEMENT AND LOCATIONS OF THE MECHANICALWORK. THE CONTRACTOR SHALL COORDINATE THE MECHANICAL INSTALLATION WITH THESTRUCTURE AND ALL OTHER TRADES. PERFORM ALL WORK IN ACCORDANCE WITH 2012INTERNATIONAL MECHANICAL CODE (IMC).

2. REFER TO THE ARCHITECTURAL REFLECTED CEILING PLANS FOR EXACT LOCATIONS OFTHE CEILING MOUNTED DEVICES.

3. DUCTWORK SHOWN ON THE PLANS IS SIZED AND ROUTED BASED ON INFORMATIONAVAILABLE DURING DESIGN PHASE FOR CEILING HEIGHTS, STRUCTURAL MEMBERS, ETC.ALL DUCT SIZES AND ROUTINGS MUST BE CONFIRMED IN THE FIELD BY THE CONTRACTORPRIOR TO FABRICATION AND INSTALLATION. WHERE CONFLICTS ARISE, REFER TO THEENGINEER.

4. REFER TO SENSOR MOUNTING DETAIL FOR MOUNTING HEIGHT.

5. ALL SUPPLY AIR DUCTWORK SHALL HAVE ONE LAYER OF TYPE 'A' DUCT WRAP. GENERALEXHAUST AIR DUCTWORK SHALL NOT BE INSULATED. (SEE SECTION 15840).

6. DEVICES REQUIRED TO BE ACCESSIBLE SHALL NOT BE INSTALLED ABOVE DRYWALLCEILINGS. REFER TO ARCHITECTURAL REFLECTED CEILING PLANS FOR LOCATIONS OFHARD CEILINGS.

7. TESTING, BALANCING AND ADJUSTING SHALL BE PERFORMED BY A NEBB OR AABCCERTIFIED TESTING, BALANCING, AND ADJUSTING COMPANY. SUBMIT COMPANYQUALIFICATIONS, INSTRUMENT CALIBRATION REPORTS AND SAMPLE FORMS FOR REVIEWPRIOR TO COMMENCING WORK. BALANCE THE SYSTEMS TO PROVIDE AIRFLOWS REQUIREDON THE DRAWINGS. TO THE GREATEST EXTENT POSSIBLE, BALANCE THE SYSTEM USINGDAMPERS LOCATED IN THE DUCTWORK TO +/- 10%. AIRFLOWS SHOWN ON THE DRAWINGSARE PROVIDED AS A GUIDE TO ACHIEVE UNIFORM ROOM TEMPERATURES THROUGHOUTTHE BUILDING. THE ARCHITECT SHALL BE NOTIFIED FIVE DAYS IN ADVANCE OF THE TIMEWHEN BALANCING READINGS WILL BE TAKEN SO THAT HE MAY OBSERVE THE READINGS IFHE SO DESIRES. AFTER BALANCING IS COMPLETE, SUBMIT A TYPED REPORT INDICATINGTHE FOLLOWING:

1. OUTDOOR AIR TEMPERATURES AT TIME OF TAB PROCEDURES

2. ENTERING AND LEAVING AIR TEMPERATURES FOR ALL COOLING COILS

3. ENTERING AND LEAVING AIR TEMPERATURES FOR ALL HEATING COILS

4. CALCULATED COIL CAPACITIES (COOLING AND HEATING)

5. CFM FOR ALL DIFFUSERS AND GRILLES

PATCH HOLES IN INSULATION , DUCTWORK AND HOUSING, WHICH HAVE BEEN CUT ORDRILLED FOR TEST PURPOSES, IN A MANNER RECOMMENDED BY THE ORIGINAL INSTALLER.

MARK EQUIPMENT SETTINGS, INCLUDING MANUAL DAMPER CONTROL POSITIONS, ANDSIMILAR CONTROLS AND DEVICES, TO SHOW FINAL SETTINGS AT COMPLETION OF TABWORK. PROVIDE MARKING WITH PAINT OR OTHER SUITABLE PERMANENT IDENTIFICATIONMATERIALS.

DEMOLITION NOTES:

1. THE DRAWINGS SHOW THE GENERAL ARRANGEMENT AND LOCATIONS OF EXISTINGMECHANICAL WORK. THE CONTRACTOR SHALL FIELD-VERIFY LOCATIONS PRIOR TOPERFORMING DEMOLITION WORK AND SHALL NOTIFY THE ENGINEER OF ANY CONFLICTS ORDISCREPANCIES. DUCTWORK AND EQUIPMENT LOCATIONS WERE DETERMINED BASED ONORIGINAL MECHANICAL PLANS AND LIMITED FIELD OBSERVATION. DETAILED ABOVE CEILINGVERIFICATION HAS NOT BEEN PERFORMED.

2. HATCHING INDICATES ITEMS TO BE DEMOLISHED UNLESS NOTED OTHERWISE. DEMOLISHEDITEMS SHALL BE REMOVED FROM THE SITE AND DISPOSED OF BY THE CONTRACTOR.DEMOLITION OF ITEMS IN THIS PROJECT INCLUDED DUCTWORK, DUCTWORK HANGARSAND/OR SUPPORTS, DIFFUSERS, GRILLES, ETC.

3. OPENINGS LEFT IN DUCTWORK SHALL BE CAPPED AND SEALED USING SHEETMETAL PANELSMATCHING THE THICKNESS OF THE EXISTING DUCTWORK. REPAIR INSULATION WITH TYPE 'A'DUCT WRAP. (SEE SECTION 232110).

AIR DISTRIBUTION SCHEDULEDESIGNATION DESCRIPTION

A 6" ROUND NECK SQUARE CEILING DIFFUSER, LAY-IN

B 8" ROUND NECK SQUARE CEILING DIFFUSER, LAY-IN

C 10" ROUND NECK SQUARE CEILING DIFFUSER, LAY-IN

D 1'x2' EGGCRATE RETURN GRILLE, LAY-IN PANEL

EX EXISTING DIFFUSER / GRILLE TO REMAIN

1. REFER TO SPEC SECTION 15870 FOR FURTHER INFORMATION.

T

PROFESSIONAL

NEER

IGNE

SIGER

ERED

No. 36592

IGROEG

A

E

A

A.BSA

MOH

T

L

NOT TO SCALEM0.1

4 DIFFUSER / GRILLE DETAIL - RECTANGULAR TRUNKS

NOT TO SCALEM0.1

2 DIFFUSER / GRILLE DETAIL - ROUND TRUNKS

NOT TO SCALEM0.1

1 SENSOR MOUNTING DETAIL

NOT TO SCALEM0.1

3 RECTANGULAR DUCT TAKE-OFF DETAIL

DEMOLITION NOTES:

1. DEMOLISH DIFFUSER / GRILLE AND ASSOCIATED FLEX DUCT (WHERE APPLICABLE). ASSOCIATED BRANCH / TRUNK DUCT SHALL REMAIN UNLESS OTHERWISE NOTED.

2. DEMOLISH DIFFUSER / GRILLE, ASSOCIATED FLEX DUCT (WHERE APPLICABLE), BRANCH DUCT AND BRANCH DUCT CONNECTION TO TRUNK DUCT. ASSOCIATED TRUNK DUCT SHALL REMAIN UNLESS OTHERWISE NOTED. CAP OPENINGS IN REMAINING TRUNK DUCT.

3. DEMOLISH DIFFUSER / GRILLE, ASSOCIATED FLEX DUCT (WHERE APPLICABLE) AND THE BRANCH DUCT UP TO THE POINT INDICATED ON THE DRAWINGS. ASSOCIATED BRANCH / TRUNK DUCT SHALL REMAIN UNLESS OTHERWISE NOTED.

4. DEMOLISH EXISTING THERMOSTAT TO UNIT C1-4 ON WALL.

5. NO MECHANICAL RENOVATION WORK PAST THIS POINT.

NOTE 5

EXISTING MECHANICAL UNIT (C1-3) IN CLOSET SHALL REMAIN.

NOTE 5

NOTE 5

NOTE 5

EXISTING MECHANICAL UNIT (C1-4) IN STORAGE ROOM SHALL REMAIN.

EXISTING MECHANICAL UNIT (C1-5) IN CLOSET SHALL REMAIN. ALL ASSOCIATED DUCTWORK, DIFFUSERS AND SUPPLY REGISTERS SHALL BE DEMOLISHED.

NOTE 1(TYP.)

NOTE 2

NOTE 3

NOTE 3

NOTE 4

NOTE 2

NOTE 2

NOTE 2

NOTE 2

RE

LO

CA

TIO

NM

UN

ICIP

AL

CO

UR

T



www.btbbinc.com


ISSUANCES

18-025

PLANNERSARCH ITECTS

ARCHITECTS PLANNERS

CO

RN

ER

MU

LB

ER

RY

& S

EC

ON

D S

T.

MA

CO

N, G

EO

RG

IA@

BC

CH

FIR

ST

FLO

OR

M1.1

MECHANICALDEMOLITION PLAN


SCALE: 1/8" = 1'-0"M1.1

1 MECHANICAL DEMO PLAN

T

PROFESSIONAL

NEER

IGNE

SIGER

ERED

No. 36592

IGROEG

A

E

A

A.BSA

MOH

T

L

DD

RAMP DN.

RAMP UP

K-2032GREENW

ICHLAVATO

RYVITREO

US CHINA


DEPUTY CLERK

114

CL.

110

TL.

112

CL.

111

JUDGE'S CHAMBERS

113

CL.

108

TL.

107

PROBATION AIDE

105

PROBATION

104

DEPUTY CLERK

106

WAITING

101

CL.

103

TL.

102

MUNICIPALCOURTROOM

109

DEPUTY CLERK

115

WORK STATIONS

116

FRONT COUNTER

117

BREAK

122

FILES

121

FILES

120

CHIEF CLERK

119

COPY/SUPPLY

118

ALCOVE

123

SHEET NOTES:

1. EXISTING DUCT SIZES ARE BASED ON EXISTING DRAWINGS, HAVE NOT BEEN VERIFIED AND ARE FOR REFERENCE ONLY. CONTRACTOR SHALL FIELD VERIFY ALL EXISTING DUCT SIZES AND NOTIFY THE ENGINEER OF ANY DISCREPANCIES.

2. ATTACH NEW FLEX DUCT TO EXISTING BRANCH DUCT. MATCH NEW FLEX DUCT SIZE TO DIFFUSER NECK SIZE UNLESS OTHERWISE NOTED. PROVIDE TRANSITION TO EXISTING BRANCH DUCT AS NEEDED.

3. NEW DIFFUSER / GRILLE IN CEILING. BALANCE TO THE AIRFLOW INDICATED ON THE DRAWINGS (SEE GENERAL MECHANICAL NOTE 7 ON SHEET M0.1).

4. ATTACH NEW DUCT TO EXISTING TRUNK DUCT.

5. EXISTING MECHANICAL UNIT (C1-5) IN CLOSET TO REMAIN. ATTACH NEW 12x10 SUPPLY TRUNK DUCT TO EXISTING UNIT.

6. NO MECHANICAL RENOVATION WORK PAST THIS POINT.

7. INSTALL NEW THERMOSTAT FOR UNIT C1-4. THERMOSTATS SHALL BE THE HEAT PUMP MANUFACTURER'S DIGITAL WALL MOUNTED AUTOMATIC CHANGEOVER HEATING/COOLING THERMOSTAT WITH SYSTEM HEAT/COOL/AUTO/OFF SWITCH, FAN ON/AUTO SWITCH, AND EMERGENCY ELECTRIC HEAT SWITCH WITH INDICATING LIGHT. COOLING AND HEATINGSTAGING SHALL MATCH THE UNIT CAPABILITIES.

NOTE 6

EXISTING MECHANICAL UNIT (C1-3) IN CLOSET SHALL REMAIN.

NOTE 6

NOTE 6

NOTE 6

EXISTING MECHANICAL UNIT (C1-4) IN STORAGE ROOM SHALL REMAIN.

NOTE 5

B3

2108ø D

1006ø

DD

6ø

10x8

MD

B4

180 7ø

12x8B4

225

10x4TYP. OF (4)

8øTYP. OF (4)

(4)

A2

80

C4

300

10ø26x8

22x8

15x8

15x8

15x4

6ø

A4

100

6ø

22x14

38x8

12x810x10

10ø12x11

10x10 8ø

8øEX

210

EX

210

10x6

14x12

14x126ø

6ø

B4

235B4

235

11x58ø

8ø

D

105

6ø

A2

110

7ø

8ø

B4

250

B4

160(2)

7ø

7ø

12x10

12ø

D

D

NOTE 2(TYP.)

NOTE 3(TYP.) NOTE 4

(TYP.)

NOTE 1(TYP.)

C1-4


14x18 UP TO EXISTING ERV

EX

50

EX

0

NOTE 7

RE

LO

CA

TIO

NM

UN

ICIP

AL

CO

UR

T



www.btbbinc.com


ISSUANCES

18-025

PLANNERSARCH ITECTS

ARCHITECTS PLANNERS

CO

RN

ER

MU

LB

ER

RY

& S

EC

ON

D S

T.

MA

CO

N, G

EO

RG

IA@

BC

CH

FIR

ST

FLO

OR

M2.1

MECHANICAL PLAN


SCALE: 1/8" = 1'-0"M2.1

1 MECHANICAL PLAN

T

PROFESSIONAL

NEER

IGNE

SIGER

ERED

No. 36592

IGROEG

A

E

A

A.BSA

MOH

T

L

FIRE ALARM SIGNAL, SPEAKER AND FLASHING LIGHT, 80" AFF TO THE BOTTOM OF THE LINES. "C" DESIGNATION INDICATES CEILING MOUNTED.

FIRE ALARM STROBE LIGHT, 80" AFF TO THE BOTTOM OF THE LENS.

FIRE ALARM:

THE CONTRACTOR SHALL PROVIDE ROUGH-IN FOR ALL DEVICES AND WIRING. ROUGH-IN REQUIREMENTS ARE SPECIFIED IN SECTION 261010. VERIFY ADJACENCY TO CORRESPONDING POWER RECEPTACLES. COORDINATE ROUGH-IN REQUIREMENTS WITH SYSTEM INSTALLER.

WALL MTD. VOICE/DATA CABLING BY OTHERS. PROVIDE TELECOMMUNICATION JUNCTION BOX AND CONDUIT ROUGH-IN TO NEAREST ACCESSIBLE CEILING

CEILING MTD. ACCESS POINT BY OTHERS. PROVIDE TELECOMMUNICATION JUNCTION BOX AND CONDUIT ROUGH-IN TO NEAREST ACCESSIBLE CEILING

CEILING MTD. CAMERA BY OTHERS. PROVIDE TELECOMMUNICATION JUNCTION BOX AND CONDUIT ROUGH-IN TO NEAREST ACCESSIBLE CEILING

ROUGH-IN FOR LOW VOLTAGE SYSTEMS:

ABBREVIATIONS:

LEGEND:LIGHTING FIXTURES: ELECTRICAL EQUIPMENT:

GENERAL NOTES:

BRANCH CIRCUITS:

CONDUCTOR COUNTS ARE SHOWN ON THE HOMERUNS ONLY. CONTRACTOR SHALL DETERMINE COUNTS FOR INTERMEDIATE RUNS BASED ON THE MANNER IN WHICH THE CIRCUIT ELEMENTS ARE CONNECTED. REFER TO THE SPECIFICATIONS FOR SPECIAL REQUIREMENTS.

LA-1,3,5

PANELBOARD: SURFACE MOUNTED

BRANCH CIRCUIT: CONCEALED

'HOMERUN' TO PANEL: NUMBER OF HASH MARKS INDICATES QUANTITY OF No. 12 AWG UNGROUNDED CONDUCTORS IN 3/4" RACEWAY. GROUNDED CONDUCTORS (NEUTRALS) ARE NOT SHOWN - ONE DEDICATED NEUTRAL IS REQUIRED FOR EACH UNGROUNDED CONDUCTOR INSTALLED, SEE SPECIFICATIONS. EACH CONDUCTOR SHALL BE MIN. No. 12 AWG UNLESS NOTED OTHERWISE.

WHERE COMPLETE BRANCH CIRCUIT WIRING IS NOT SHOWN, PROVIDE ACCORDING TO HOMERUNS SHOWN AND CORRESPONDING CIRCUIT NUMBERS ADJACENT TO THE DEVICE OR FIXTURE. REFER TO THE SPECIFICATIONS FOR THE WIRING METHODS. BRANCH CIRCUIT RATINGS SHALL BE BASED ON OVERCURRENT DEVICE RATINGS SHOWN IN THE PANEL SCHEDULES.

REFER TO THE ELECTRICAL PANELBOARD SCHEDULES AND EQUIPMENT RATINGS & CONNECTIONS SCHEDULE FOR VOLTAGE, BRANCH CIRCUITS REQUIREMENTS, BREAKERS SIZES AND OTHER RELATED ELECTRICAL EQUIPMENT TO BE PROVIDED AND/OR INSTALLED BY THE ELECTRICAL CONTRACTOR.

A AMPERES

AFF ABOVE FINISHED FLOOR

AFG ABOVE FINISHED GRADE

AH AIR HANDLER

AIC AMPERE INTERRUPTING CAPACITY

ATU AIR TERMINAL UNIT

A/V AUDIO/VISUAL

AWG AMERICAN WIRE GAUGE

BFG BELOW FINISHED GRADE

B.E. BOTTOM EDGE

C. CONDUIT

CU CONDENSING UNIT

DAH DUCTLESS AIR HANDLER

DHP DUCTLESS HEAT PUMP

DIA. DIAMETER

THE ELECTRICAL DRAWINGS ARE ONLY PART OF THE CONTRACT DOCUMENTS.THE CONTRACTOR SHALL REVIEW ALL OF THE DRAWINGS AND SPECIFICATIONSFOR THEIR INTERRELATIONSHIP AND REQUIRED COORDINATION BETWEEN DISCIPLINES.

1.

ECB ENCLOSED CIRCUIT BREAKER

EF EXHAUST FAN

EH ELECTRIC HEATER

EMCS ENERGY MANAGEMENT CONTROL UNIT

FAAP FIRE ALARM ANNUNCIATOR PANEL

FACP FIRE ALARM CONTROL PANEL

G GROUND

GFI GROUND-FAULT INTERRUPTING

HP HORSE POWER

HRVU HEAT RECOVERY VENTILATING UNIT

HWCP HOT WATER CIRCULATING PUMP

KCMIL KILO CIRCULAR MIL

MAH MAKEUP AIR HEATER

MB MAIN BREAKER

MCA MINIMUM CIRCUIT AMPS

MIN MINIMUM

MOCP MAXIMUM OVERCURRENT PROTECTION

MTD MOUNTED

No. NUMBER

NEC NATIONAL ELECTRIC CODE

NTS NOT TO SCALE

PIV POST INDICATOR VALVE

RGS RIGID GALVANIZED STEEL

RTU ROOFTOP UNIT

SF SUPPLY FAN

SPD SURGE PROTECTION DEVICE

SWBD SWITCHBOARD

TGB TELECOMMUNICATIONS GROUND BUS

TMGB TELECOMMUNICATIONS MAIN GROUND BUS

TTW THROUGH-THE-WALL HEAT PUMP

TYP TYPICAL

UH UNIT HEATER

UNO UNLESS NOTED OTHERWISE

V VOLTAGE

W WATTAGE

W/ WITH

WH WATER HEATER

WHP WALL-MOUNTED HEAT PUMP

WP WEATHER PROOF

XFMR TRANSFORMER

UPPERCASE LETTER ADJACENT TO FIXTURE DENOTES DESIGNATION PER THE LIGHTING FIXTURE SCHEDULE. LOWERCASE LETTER DENOTES SWITCHLEG. THE RESPECTIVE SWITCH WILL HAVE THE SAME DESTINATIONS. NUMERAL DENOTES BRANCH CIRCUIT CONNECTION.

REFER TO THE FIXTURE SCHEDULE FOR THE SPECIFIC FIXTURE INFORMATION.

OS

OS

RECEPTACLES:

NOMINAL MOUNTING HEIGHT OF RECEPTACLES SHALL BE 18" TO CENTER, UNO. IF APPLICABLE, ADJUST SO DEVICE COVER IS IN THE CENTER OF MASONRY COURSE NEAREST THAT HEIGHT. THE HEIGHT ESTABLISHED SHALL GOVERN FOR ALL BOX INSTALLATIONS, WHERE INSTALLED IN MASONRY OR FRAMED WALLS.

ALL RECEPTACLES INSTALLED IN THE FOLLOWING LOCATIONS SHALL BE TAMPER RESISTANT TYPE:A. DWELLING UNITS, DORM ROOMS, GUEST ROOMS AND GUEST SUITES OF HOTELS

AND MOTELS.B. CHILD CARE FACILITIES.C. PRESCHOOLS AND ELEMENTARY EDUCATION FACILITIES.D. BUSINESS OFFICES, CORRIDORS, WAITING ROOMS AND THE LIKE IN CLINICS,

MEDICAL AND DENTAL OFFICES AND OUTPATIENT FACILITIES.E. SUBSETS OF ASSEMBLY OCCUPANCIES DESCRIBED IN NEC 518.2 TO INCLUDE

PLACES OF WAITING TRANSPORTATION, GYMNASIUMS, SKATING RINKS, AND AUDITORIUMS.

SWITCHES:

MOUNTING HEIGHT OF SWITCHES SHALL BE 48" NOMINAL, ADJUSTED IN THE SAME MANNER AS SPECIFIED ABOVE, FOR RECEPTACLES. LOWERCASE LETTER INDICATES SWITCHLEG CONNECTION. THE RESPECTIVE FIXTURE(S) WILL HAVE THE SAME DESIGNATION.

3

O

RECEPTACLE: SIMPLEX

RECEPTACLE: DUPLEX

RECEPTACLE: GROUND-FAULT-INTERRUPTING TYPE

SWITCH: SINGLE-POLE

SWITCH: THREE-WAY TYPE

SWITCH: OVERRIDE

OCCUPANCY SENSOR, CEILING MOUNTED

OCCUPANCY SENSOR, WALL MOUNTED

VS

VS VACANCY SENSOR, CEILING MOUNTED

VACANCY SENSOR, WALL MOUNTED

V

SWITCH: LOW VOLTAGE OVERRIDE SWITCH FOR VACANCYSENSOR.

LIGHTING FIXTURE: LINEAR

NON-EMERGENCY

EMERGENCY/GENERATOR BACKUP

LIGHTING FIXTURE: LINEAR

LIGHTING FIXTURE: WALL MTD.

DOWNLIGHT/SCONCE FIXTURE

EXIT LIGHT

DIRECTIONAL FIXTURES: EMERGENCY TYPE

DEVICE IDENTIFIER TAGS:

NUMERAL ADJACENT TO DEVICE DENOTES BRANCH CIRCUIT CONNECTION. IDENTIFIER TAGS ADJACENT TO DEVICES INDICATE:

MOUNT ABOVE COUNTERTOP OR BACKSPLASH, 9" ABOVE WORK SURFACE TO CENTER

MOUNT DEVICE AT HEIGHT INDICATED

C

XX"

REFER TO ONE-LINE DIAGRAM AND EQUIPMENT CONNECTION SCHEDULE FOR LOAD DATA USED AS THE BASIS OF DESIGN AND REQUIRED CONNECTIONS. VERIFY LOAD AND LOCATION WITH EQUIPMENT CUT-SHEETS AND INSTALLER.

2.

3.

J

J

MISCELLANEOUS COMPONENTS:

JUNCTION BOX: MTD. ABOVE CEILING

JUNCTION BOX: WALL MTD.

C

AP

THE CONTRACTOR SHALL PROVIDE ROUGH-IN FOR ALL DEVICES AND WIRING. COORDINATE ROUGH-IN REQUIREMENTS WITH SYSTEM INSTALLER.

PANIC BUTTON BENEATH DESK

ROUGH-IN FOR ACCESS CONTROLS

P

ML MAG LOCK IN DOOR FRAME

MANUAL REQUEST TO EXIT IN SINGLE GANG BOX BENEATH DESK

R

CR CARD READER IN SINGLE GANG BOX AT 45" AFF.

DS DOOR STRIKE IN DOOR FRAME

CONT. CONTROLLER IN TRIPLE GANG BOX WITH COVER ABOVE ACCESSIBLE CEILING

MANUAL REQUEST TO EXIT IN SINGLE GANG BOX AT 45" AFF.

RW

DOOR CONTACTDC

RECEPTACLE: QUADRUPLEX

RE

LO

CA

TIO

NM

UN

ICIP

AL

CO

UR

T



www.btbbinc.com


ISSUANCES

18-025

PLANNERSARCH ITECTS

ARCHITECTS PLANNERS

CO

RN

ER

MU

LB

ER

RY

& S

EC

ON

D S

T.

MA

CO

N, G

EO

RG

IA@

BC

CH

FIR

ST

FLO

OR

E0.1

ELECTRICALLEGEND &SCHEDULES


LIGHT FIXTURE SCHEDULE

TYPE DESCRIPTION LAMPSMANUFACTURER /

SERIESFINISH MOUNTING NOTES

A2'X4' VOLUMETRIC TROFFER WITH

CURVED FROSTED DIFFUSER

LED:4900 LUMENS

4000K

COLUMBIA "LCAT" SERIESLITHONIAMETALUX

WHITE RECESSED

B2'X2' VOLUMETRIC TROFFER WITH

CURVED FROSTED DIFFUSER

LED:3400 LUMENS

4000K

COLUMBIA "LCAT" SERIESLITHONIAMETALUX

WHITE RECESSED

CSTRIP FIXTURE, 2 FOOT LENGTH,

WITH FROSTED LENS

LED:2500 LUMENS

4000K

COLUMBIA "LCL" SERIESLITHONIAMETALUX

WHITEWALL -

SURFACE

DSTRIP FIXTURE, 4 FOOT LENGTH,

WITH FROSTED LENS

LED:5000 LUMENS

4000K

COLUMBIA "LCL" SERIESLITHONIAMETALUX

WHITEWALL -

SURFACE

EDOWNLIGHT, RECESSED SELF

FLANGED, 6" APERTURE, CLEARMATT DIFFUSE REFLECTOR

LED:1500 LUMENS

4000K

PRESCOLITE "LF6" SERIESGOTHAM

HALOWHITE RECESSED

F VANITY WALL SCONCE, 19" LENGTHLED:

1000 LUMENS4000K

VISA SHINEACUITY

COOPERWHITE

WALL -SURFACE

X

SINGLE FACE EXIT LIGHT, EDGE LIT,UNIVERSAL MOUNTING, GREEN

LETTERS - DIRECTION OF ARROWSAS INDICATED

LEDDUAL-LITE "LE" SERIES

LITHONIASURE-LITES

CLEAR UNIVERSAL

No. 32283

RT

PROFESSIONAL

OEG

G I A

NE ER

IGNE

SIGER

ERED

O.Y

W

EO

L

M

S

M

E

A

W

CK

No. 32283

RT

PROFESSIONAL

OEG

G I A

NE ER

IGNE

SIGER

ERED

O.Y

W

EO

L

M

S

M

E

A

W

CK

S S

S

S J

J

S

S3

SJ

JS

S

J

J

S

S

60"

60" 60"

48"

60"60"

60"

60"

60"

48"

60"

EMERGENCY PANIC BUTTON

EMERGENCY PANIC BUTTON

48"

C

48"

C

NOTE 1

NOTE 2

NOTE 3

NOTE 4

NOTE 1

NOTE 1

EXISTING FIRE ALARM DEVICE TO BE RELOCATED

NOTE 1

NOTE 5

NOTE 5 NOTE 5NOTE 5

DEMOLITION NOTES:A. THIS PLAN HAS BEEN PROVIDED AS A GENERAL SCOPE OF DEMOLITION REQUIRED.

THE CONTRACTOR SHALL VERIFY ALL SITE CONDITIONS AND REMOVE ITEMS INDICATED IN THESE DEMOLITION NOTES ON THIS SHEET WHETHER THE SPECIFIC ITEM IS SHOWN ON THE DEMOLITION PLAN OR NOT.

B. EQUIPMENT SHOWN HATCHED SHALL BE REMOVED. ALL OTHER EQUIPMENT SHALL REMAIN UNLESS NOTED OTHERWISE.

C. ENSURE ANY EXISTING LOW VOLTAGE CABLING TO REMAIN IS SECURED TO STRUCTURE WITH J-HOOKS AND PROTECTED FROM DAMAGE DURING DEMOLITION AND NEW CONSTRUCTION. CONTRACTOR IS RESPONSIBLE FOR KEEPING THESE SYSTEMS IN WORKING ORDER. PROVIDE 4" J-HOOK AS REQUIRED.

D. REMOVE ALL ELECTRICAL OUTLETS ON WALLS SCHEDULED TO BE DEMOLISHED. COORDINATE ALL WALLS BEING DEMOLISHED WITH ARCHITECTURAL.

E. EXISTING CEILINGS, WALLS, AND FLOORS DISTURBED OR DISFIGURED BY THE ELECTRICAL RENOVATION SHALL BE PATCHED, MENDED OR REPLACED BY TRADES ACTIVELY PARTICIPATING IN THIS TYPE OF WORK. RESPONSIBILITY FOR REPAIRS SHALL BE COORDINATED BETWEEN GENERAL CONTRACTOR AND ELECTRICAL SUBCONTRACTOR.

F. ALL EXISTING EQUIPMENT REMOVED FROM SERVICE AND NOT INTENDED FOR REUSE SHALL REMAIN THE PROPERTY OF OWNER AND SHALL BE DISPOSED OF OR STORED AS DIRECTED BY THE OWNER, OR AS INDICATED ON PLANS.

G. MAINTAIN SERVICE TO ALL EXISTING CIRCUITS THAT ARE NOT SCHEDULED FOR REMOVAL.

H. REMOVE ANY ABANDONED SURFACE RACEWAY TO ABOVE CEILING.

I. WHERE ONLY A PORTION OF A CIRCUIT'S LOAD IS SCHEDULED TO BE REMOVED, REMOVE ONLY THAT PORTION ASSOCIATED WITH THE DEMOLISHED DEVICE TO A POINT WHERE THE REMAINING LOAD IS ACTIVE AND MAINTAIN IN A GOOD OPERATING CONDITION.

J. EXISTING EQUIPMENT NOT SCHEDULED FOR DEMOLITION ON ARCHITECTURAL, MECHANICAL, PLUMBING AND ELECTRICAL DRAWINGS SHALL HAVE SERVICE MAINTAINED OR RECONNECTED TO EXISTING OR NEW PANELBOARD AS NECESSARY.

K. TO MAINTAIN SERVICE OR EXTEND OR RECONNECT CIRCUITS WHERE CONDUIT CAN NOT BE CONCEALED, SURFACE METAL RACEWAY (WIREMOLD 2000 SERIES) SHALL BE USED IN FINISHED AREAS, EMT CONDUIT OTHERWISE - VERIFY WITH ARCHITECT BEFORE INSTALLING.

L. COORDINATE ELECTRICAL DEMOLITION WITH ARCHITECTURAL DETAILS, FLOOR PLANS, ELEVATIONS, STRUCTURAL, MECHANICAL AND PLUMBING DRAWINGS. PROVIDE FITTINGS, JUNCTION BOXES AND ACCESSORIES TO MEET CONDITIONS. COORDINATE ROUTING OF ALL NEW FEEDERS WITH EXISTING SITE ELEMENTS. ALL FEEDERS SHALL BE CONCEALED WHERE POSSIBLE.

M. REMOVE ELECTRICAL CONNECTIONS/FEEDERS TO MECHANICAL AND PLUMBING EQUIPMENT BEING REMOVED. COORDINATE WITH MECHANICAL/PLUMBING PLANS. WHERE EQUIPMENT IS BEING REPLACED AT SAME LOCATION WITH SAME ELECTRICAL CHARACTERISTICS AS EXISTING, EXISTING CIRCUIT SHALL BE RE-USED TO SUPPLY POWER TO NEW ITEM. WHERE EQUIPMENT IS BEING REMOVED AND NOT BEING REPLACE: REMOVE CIRCUIT AND ASSOCIATED DISCONNECT, ACCESSIBLE CONDUIT AND CONDUCTORS. COORDINATE ALL EQUIPMENT AND LOCATIONS OF EQUIPMENT BEING REMOVED WITH MECHANICAL/PLUMBING PLANS.

N. FIELD VERIFY EXACT LOCATIONS OF ALL EXISTING DEVICES AND EQUIPMENT NOTED OR SHOWN.

O. WHERE WALL BOXES FOR SWITCHES AND OUTLETS ARE REMOVED AND NOT RE-USED IN COMPLETE WORK, CONTRACTOR SHALL PROVIDE BLANK PAINTABLE STEEL COVERPLATES OVER JUNCTION BOXES.

P. WHERE CEILINGS ARE BEING REMOVED, TEMPORARILY SUPPORT ALL CEILING MOUNTED ELECTRICAL DEVICES TO REMAIN (SECURITY SYSTEM DEVICES, ETC.) AND REINSTALL IN THE SAME LOCATION IN THE NEW CEILING. SEE ARCHITECTURAL FOR CEILINGS BEING REPLACED.

Q. WHERE RECEPTACLES AND DEVICES ARE BEING REMOVED FROM EXISTING CIRCUITS FEEDING RECEPTACLES TO REMAIN, SPLICE AND EXTEND CIRCUITS (PER N.E.C. REQUIREMENTS) AS REQUIRED TO MAINTAIN FULL OPERATION. PROVIDE ADDITIONAL CONDUIT AND WIRING AS REQUIRED.

R. FIRE ALARM SYSTEM SHALL BE OPERATIONAL THROUGHOUT CONSTRUCTION. COORDINATE ANY DOWN TIME WITH OWNER MINIMUM ONE WEEK IN ADVANCE.

S. PROVIDE NEW RECEPTACLE, SWITCH, AND FACEPLATE FOR ALL EXISTING WIRING DEVICES SHOWN TO REMAIN. IF EXISTING DEVICES SHOWN TO REMAIN HAVE SURFACE MOUNTED RACEWAY, PROVIDE NEW SURFACE MOUNTED RACEWAY PER SPECIFICATIONS.

T. WHERE COMMUNICATIONS OUTLETS ARE SHOWN HATCHED, REMOVE BOX, CONDUIT AND CABLING BACK TO SERVING RACK OR BACKBOARD. FOR COMMUNICATIONS OUTLETS SHOWN TO REMAIN (NOT HATCHED), BOX AND CONDUIT TO ABOVE ACCESSIBLE CEILING MAY BE REUSED FOR NEW VOICE/DATA OUTLETS SHOWN ON NEW WORK PLANS.

RE

LO

CA

TIO

NM

UN

ICIP

AL

CO

UR

T



www.btbbinc.com


ISSUANCES

18-025

PLANNERSARCH ITECTS

ARCHITECTS PLANNERS

CO

RN

ER

MU

LB

ER

RY

& S

EC

ON

D S

T.

MA

CO

N, G

EO

RG

IA@

BC

CH

FIR

ST

FLO

OR

E1.1

ELECTRICALDEMOLITION PLAN


SCALE: 1/8" = 1'-0"E1.1

1 ELECTRICAL DEMO PLAN

NOTES:1. EXISTING FLUSH MOUNTED SWITCH TO BE REMOVED. BOX AND CONDUIT

TO ABOVE ACCESSIBLE CEILING SHALL REMAIN AND BE REUSED FOR NEW SWITCH BEING INSTALLED IN SAME LOCATION.

2. EXISTING LIGHT FIXTURES IN THIS SPACE TO REMAIN. REWORK BRANCH CIRCUITRY THRU NEW LIGHT SWITCH AS SHOWN ON SHEET E2.1.

3. REMOVE (2) 2x4 TROFFERS ABOVE STAIRS. CIRCUITRY SHALL REMAIN TO SERVE (2) NEW FIXTURES IN SAME LOCATION.

4. REMOVE EXISTING 3-WAY SWITCH SERVING LIGHTS ABOVE STAIRS. NEW 3-WAY SWITCH SHALL BE INSTALLED IN NEW LOCATION. SEE NEW LIGHTING PLAN SHEET E2.1.

5. REMOVE ALL LIGHT FIXTURES, SWITCHES, AND OUTLETS IN THIS AREA.

No. 32283

RT

PROFESSIONAL

OEG

G I A

NE ER

IGNE

SIGER

ERED

O.Y

W

EO

L

M

S

M

E

A

W

CK

K-3246-4BALLADSINKSSTAINLESS STEEL

DD

D

RAMP DN.

RAMP UP

K-2032GREENW

ICHLAVATO

RYVITREO

US CHINA


S

SV

SV

SV

SV

SV

VS

SV

VSVS

VSVSVSVS

VS

VSVS

OSOS

SO

VS

OSOS

OSOS

OSOS

OSOS

OSOS

SV

VSVS

VS

VS

VS

SO

S3

VS

OS

DEPUTY CLERK

114

CL.

110

TL.

112

CL.

111

JUDGE'S CHAMBERS

113

CL.

108

TL.

107

PROBATION AIDE

105

PROBATION

104

DEPUTY CLERK

106

WAITING

101

CL.

103

TL.

102

MUNICIPALCOURTROOM

109

DEPUTY CLERK

115

WORK STATIONS

116

FRONT COUNTER

117

BREAK

122

FILES

121

FILES

120

CHIEF CLERK

119

COPY/SUPPLY

118

ALCOVE

123

NOTE 2

NOTE 1

NOTE 1

NOTE 1

NOTE 1

NOTE 1

NOTE 1

NOTE 1

NOTE 3 NOTE 3

NOTE 3

NOTE 3

NOTE 3

NOTE 3

NOTE 3

A 2 A 2A A

D A 2 A

C 2

B 2

A 2

A 2

A 2 A 2 A 2 A 2

A 2

A

A 2 A 2 A A 2

A 2 A 2

A 2 A 2 A 2

A 2A A 2

A 2

A 2 A 2

A 2

A 2

A A 2 A 2

B 2

A 2 A 2 A 2

D 2

X

X

X

X

NOTE 4

X

X

NOTE 4

NOTE 4

NOTE 4

NOTE 4

C 2

2

A(2)

2

L1-2

C2

F 2

E 2 E 2

c

c

c

c

a a a a

aa

a

b b b

b

b

b

b

bb

NOTE 4

X

EMERGENCY PANEL

VOLTAGE SENSING

AC BALLAST

OR DRIVER

LIGHTING CONTROLS

NORMAL POWER

N

NEUTRAL BUS FOR NORMAL POWER

NEUTRAL BUS FOR EMERGENCY POWER

BLACK

WHITEGENERAL NOTES:A. PROVIDE CONCEALED RACEWAY AND BOXES FOR ALL DEVICES IN NEW WALLS. ON

EXISTING WALLS THAT CAN NOT BE FISHED, PROVIDE SURFACE RACEWAY DOWN WALL TO NEW DEVICE. CONFIRM ALL NEW WALL LOCATIONS WITH ARCHITECTURAL PLANS.

B. WHERE SURFACE RACEWAY IS USED AS DESCRIBED ABOVE, PROVIDE WIREMOLD 2000 SERIES SURFACE METAL RACEWAY. COORDINATE RACEWAY COLOR WITH ARCHITECT.

C. PROVIDE SURFACE RACEWAY OFFSETS AS REQUIRED FOR COLUMNS, WINDOWS, ETC.

D. THERE SHALL BE NO VISIBLE SEAMS IN SURFACE RACEWAY COVERS.

E. THERE SHALL BE NO SHARP EDGES AT ANY SEAM ON SURFACE RACEWAY.

F. WHERE WIREMOLD 2000 SERIES SURFACE RACEWAY IS USED, PROVIDE WIREMOLD V2048 SERIES STYLE SINGLE OR DOUBLE GANG DEVICE BOXES. OTHER ACCEPTABLE MANUFACTURES: MONOSYSTEMS, TRB.

G. SURFACE METAL RACEWAY SHALL BE ANCHORED TO WALLS. ADHESIVE TYPE IS NOT ACCEPTABLE.

RE

LO

CA

TIO

NM

UN

ICIP

AL

CO

UR

T



www.btbbinc.com


ISSUANCES

18-025

PLANNERSARCH ITECTS

ARCHITECTS PLANNERS

CO

RN

ER

MU

LB

ER

RY

& S

EC

ON

D S

T.

MA

CO

N, G

EO

RG

IA@

BC

CH

FIR

ST

FLO

OR

E2.1

LIGHTING PLAN


SCALE: 1/8" = 1'-0"E2.1

1 LIGHTING PLAN

NOTES:1. PROVIDE ALL NEW FLUORESCENT LAMPS FOR EACH EXISTING TROFFER

TO REMAIN IN THIS SPACE. COORDINATE QUANTITY, TYPE, AND COLOR TEMPERATURE WITH EXISTING. ALL LIGHTS WITHIN SPACE SHALL BE ILLUMINATING PROPERLY AND EVENLY WITHOUT FLICKER UPON COMPLETION OF PROJECT. PROVIDE NEW STARTER/BALLAST AS REQUIRED.

2. REWORK EXISTING LIGHTING BRANCH CIRCUITRY THRU NEW SWITCH.

3. CONNECT LIGHT FIXTURE TO NEAREST 20A/1P EMERGENCY POWER CIRCUIT. FIXTURE SHALL BE SWITCHED WITH NORMAL POWER CIRCUIT IN SAME SPACE. SEE DETAIL, 2/E2.1.

4. CONNECT EXIT LIGHT TO NEAREST 20A/1P UNSWITCHED EMERGENCY POWER CIRCUIT.

NOT TO SCALEE2.1

2 GENERATOR TRANSFER DEVICE WIRING DETAIL

No. 32283

RT

PROFESSIONAL

OEG

G I A

NE ER

IGNE

SIGER

ERED

O.Y

W

EO

L

M

S

M

E

A

W

CK

DD

D

RAMP DN.

RAMP UP

K-2032GREENW

ICHLAVATO

RYVITREO

US CHINA


DEPUTY CLERK

114

CL.

110

TL.

112CL.

111

JUDGE'S CHAMBERS

113

CL.

108

TL.

107

PROBATION AIDE

105

PROBATION

104

DEPUTY CLERK

106

WAITING

101

CL.

103

TL.

102

MUNICIPALCOURTROOM

109

DEPUTY CLERK

115

WORK STATIONS

116

FRONT COUNTER

117

BREAK

122

FILES

121

FILES

120

CHIEF CLERK

119

COPY/SUPPLY

118

ALCOVE

123

C

C

L1

NOTE 2

5

5

5

5

3

3

1

NOTE 3

60" 60"E E

60"E

E

E

E

48" E

E

E

E

E

E E

5

C

L1-1,3,5

7 7

77

5

9

L1-7,9

111113 13

17

15

15

17

17 19

19

21

21

21

19

L1-19,21

L1-11,13

L1-15,17

NOTE 4

GENERAL NOTES:A. PROVIDE CONCEALED RACEWAY AND BOXES FOR ALL DEVICES IN NEW WALLS. ON








RE

LO

CA

TIO

NM

UN

ICIP

AL

CO

UR

T



www.btbbinc.com


ISSUANCES

18-025

PLANNERSARCH ITECTS

ARCHITECTS PLANNERS

CO

RN

ER

MU

LB

ER

RY

& S

EC

ON

D S

T.

MA

CO

N, G

EO

RG

IA@

BC

CH

FIR

ST

FLO

OR

E3.1

POWER PLAN


NOTES:1. (GENERAL) FOR RECEPTACLES SHOWN WITH "E" DESIGNATION, PROVIDE

NEW DEVICE AND FACEPLATE.

2. NEW 125A, 120/208V, 3PH, 4W, MAIN LUG, SURFACE MOUNTED PANELBOARD. PROVIDE 4#1/0, #6G, 2" C. FEEDER. ROUTE FEEDER TO NEW 125A/3P CIRCUIT BREAKER IN EXISTING 400A, 120/208V SQUARE D PANELBOARD IN BASEMENT BELOW. EXISTING PANELBOARD IS FED FROM MAIN SWITCHBOARD VIA 400A DISCONNECT. MATCH EXISTING BREAKER MANUFACTURER AND TYPE. FIELD VERIFY PATH TO BASEMENT.

3. ROUTE DEDICATED RECEPTACLE TO NEW 20A/1P CIRCUIT BREAKER IN EXISTING 120/208V EMERGENCY POWER PANELBOARD IN BASEMENT. MATCH EXISTING BREAKER MANUFACTURER AND TYPE. FIELD VERIFY PATH TO BASEMENT.

4. SEE BACKBOARD DETAIL, 3/E5.1 AND TELECOMMUNICATIONS EQUIPMENT GROUND BUS DETAIL, 4/E5.1.

SCALE: 1/8" = 1'-0"E3.1

1 POWER PLAN No. 32283

RT

PROFESSIONAL

OEG

G I A

NE ER

IGNE

SIGER

ERED

O.Y

W

EO

L

M

S

M

E

A

W

CK

DD

D

RAMP DN.

RAMP UP

K-2032GREENW

ICHLAVATO

RYVITREO

US CHINA


DEPUTY CLERK

114

CL.

110

TL.

112CL.

111

JUDGE'S CHAMBERS

113

CL.

108

TL.

107

PROBATION AIDE

105

PROBATION

104

DEPUTY CLERK

106

WAITING

101

CL.

103

TL.

102

MUNICIPALCOURTROOM

109

DEPUTY CLERK

115

WORK STATIONS

116

FRONT COUNTER

117

BREAK

122

FILES

121

FILES

120

CHIEF CLERK

119

COPY/SUPPLY

118

ALCOVE

123

E E

E

E

E

E

E

IDF

AP

APC

C

C

RELOCATED FIRE ALARM DEVICE

NOTE 2NOTE 3

TO MDF

DC

DS

CR

RW

CONT.

E

E

E

P

P

P

R

P

R

P

R

P

R

RW

CR

ML

CR

ML

RW

CR

ML

RW

CONT.

CONT.

RW

ML

CR

P

P R

P

R P

R P

DC

DS

RWCR

CONT.

DC

DS

CR

RW

4

MOTOR RATEDSWITCH

3#12, 1 / 2 IN. C TO NEAREST 120 VOLT, 20 AMP UNSWITCHED RECEPTACLE CIRCUIT

1

2

3

1/2" C.

5

THIS DRAWING IS INTENDED TO INDICATE CONDUIT INFRASTRUCTUREREQUIREMENT ONLY. COORDINATE EXACT REQUIRED COMPONENTS WITH SYSTEM INSTALLER. PROVIDE ALL CONDUIT AND BOXES FOR COMPLETE ACCESS CONTROL INSTALLATION.

3#12, 1/2"C.(FLEXIBLECONDUIT)

NOTES:1

2

4

(ACCESS CONTROL CONNECTIONS)

DOOR CONTACT

CURRENT TRANSFER HINGE / DOOR STRIKE

CONTROLLER POWER SUPPLY.

CARD READER / REQUEST TO EXIT.

DELAYED EGRESS SYSTEM - NORMALLY CLOSED FIRE ALARMRELAY REQUIRED, PLUGNPLAY. NORMALLY CLOSED FIRE ALARMRELAY REQUIRED FOR THE DELAYED EGRESS APPLICATION.

3

5

TO IDF

GENERAL NOTES:A. PROVIDE CONCEALED RACEWAY AND BOXES FOR ALL DEVICES IN NEW WALLS. ON








RE

LO

CA

TIO

NM

UN

ICIP

AL

CO

UR

T



www.btbbinc.com


ISSUANCES

18-025

PLANNERSARCH ITECTS

ARCHITECTS PLANNERS

CO

RN

ER

MU

LB

ER

RY

& S

EC

ON

D S

T.

MA

CO

N, G

EO

RG

IA@

BC

CH

FIR

ST

FLO

OR

E4.1

SYSTEMSROUGH-IN PLAN


SCALE: 1/8" = 1'-0"E4.1

1 SYSTEMS ROUGH-IN PLAN

NOTES:1. (GENERAL) FIRE ALARM DEVICES SHOWN WITH "E" DESIGNATION ARE

EXISTING TO REMAIN.

2. PROVIDE 1#250 KCMIL COPPER WITH GREEN JACKET IN 1-1/4"C. BACK TO MDF TELECOMMUNICATIONS GROUND BAR. SEE VOICE/DATA SHEET LABELED VD-01 FOR EXACT LOCATION OF MDF.

3. PROVIDE 1"C. FOR FIBER CONNECTION BACK TO MDF.

NOT TO SCALEE4.1

2 ACCESS CONTROL DOOR DETAIL

No. 32283

RT

PROFESSIONAL

OEG

G I A

NE ER

IGNE

SIGER

ERED

O.Y

W

EO

L

M

S

M

E

A

W

CK

NOTES:A

B

C

D

E

(OCCUPANCY SENSOR WIRING)

POWER PACK

GROUND

NEUTRAL

HOT

RED

RED

BLACK

WHITE

RED (24VDC@100mA)

BLACK (COMMON)

BLUE (CONTROL)

RED

BLACK

BLUE

OVERRIDE SWITCH

LIGHTING LOAD

NOT ALL MANUFACTURERS' WIRING CONFIGURATIONS ARE THE SAME. REFER TO MANUFACTURER SPECIFIC WIRING DETAILS PRIOR TO INSTALLATION.

THESE PLANS INDICATE AREAS TO BE CONTROLLED BY OCCUPANCY SENSORS. SINCE COVERAGES AND DEVICES VARY BETWEEN MANUFACTURERS, IT SHALL BE THE CONTRACTOR'S RESPONSIBILITY TO COORDINATE PROPER DEVICE LOCATION, ORIENTATION, AND QUANTITIES WITH THE MANUFACTURER OF THE SYSTEM BEING INSTALLED TO MEET THE SPECIFIED CRITERIA.

THERE ARE NO POWER PACKS SHOWN ON THESE PLANS. PROVIDE POWER PACKS AS REQUIRED WITH SENSORS. POWER PACKS ARE TO BE RATED AT 20A. PROVIDE ONE POWER PACK PER 20A LIGHTING CIRCUIT OR PER INDIVIDUAL AREA BEING CONTROLLED.

CEILING SENSORS ARE TO BE MOUNTED AWAY FROM ANY STRONG AIRFLOW. COORDINATE LOCATION OF SENSORS WITH MECHANICAL AND LIGHTING PLANS.

ALL SENSORS SHALL BE CEILING MOUNTED EXCEPT WHERE CEILING HEIGHTS EXCEED 15'. PROVIDE SENSOR WITH ADAPTOR PLATE FOR JUNCTION BOX MOUNTING (JUNCTION BOX SHALL BE CONCEALED ABOVE ACCESSIBLE CEILING). JUNCTION BOX SHALL BE SUPPORTED FORM STRUCTURE UTILIZING A 3/8" THREADED ROD. WHERE CEILING HEIGHTS EXCEED 15', WALL MOUNT SENSORS AT 12'.

NEUTRAL

HOT

GROUND

RED (24VDC@100mA)

BLACK (COMMON)

BLUE (CONTROL)

RED

RED

BLACK

WHITE

RED

BLUE

BLACK

LIGHTING LOAD

3-WAY OVERRIDESWITCHES

POWER PACK

3-WAY OVERRIDE SWITCHES

1 OVERRIDE SWITCH

NEUTRAL

HOT

GROUND

RED (24VDC@100mA)

BLACK (COMMON)

BLUE (CONTROL)

RED

RED

BLACK

WHITE

RED

BLUE

BLACK

LIGHTING LOAD

"A"

OVERRIDESWITCH "B"

OVERRIDESWITCH "A"

LIGHTING LOAD

"B"

POWER PACK

2 OVERRIDE SWITCHES

NOTES:A

B

C

D

E

(VACANCY SENSOR WIRING)

NEUTRAL

HOT

LIGHTING LOAD

GROUND

RED (24VDC@100mA)

BLACK (COMMON)

BLUE (CONTROL)

RED

RED

BLACK

WHITE

RED

BLUE

BLACK

POWER PACK

ORANGE LOW VOLTAGE DUALTECHNOLOGY SENSOR

NOT ALL MANUFACTURERS' WIRING CONFIGURATIONS ARE THE SAME. REFER TO MANUFACTURER SPECIFIC WIRING DETAILS PRIOR TO INSTALLATION.

THESE PLANS INDICATE AREAS TO BE CONTROLLED BY VACANCY SENSORS. SINCE COVERAGES AND DEVICES VARY BETWEEN MANUFACTURERS, IT SHALL BE THE CONTRACTOR'S RESPONSIBILITY TO COORDINATE PROPER DEVICE LOCATION, ORIENTATION, AND QUANTITIES WITH THE MANUFACTURER OF THE SYSTEM BEING INSTALLED TO MEET THE SPECIFIED CRITERIA.

THERE ARE NO POWER PACKS SHOWN ON THESE PLANS. PROVIDE POWER PACKS AS REQUIRED WITH SENSORS. POWER PACKS ARE TO BE RATED AT 20A. PROVIDE ONE S POWER PACK PER 20A LIGHTING CIRCUIT OR PER INDIVIDUAL AREA BEING CONTROLLED.

CEILING SENSORS ARE TO BE MOUNTED AWAY FROM ANY STRONG AIRFLOW. COORDINATE LOCATION OF SENSORS WITH MECHANICAL AND LIGHTING PLANS.

ALL SENSORS SHALL BE CEILING MOUNTED EXCEPT WHERE CEILING HEIGHTS EXCEED 15'. PROVIDE SENSOR WITH ADAPTOR PLATE FOR JUNCTION BOX MOUNTING (JUNCTION BOX SHALL BE CONCEALED ABOVE ACCESSIBLE CEILING). JUNCTION BOX SHALL BE SUPPORTED FROM STRUCTURE UTILIZING A 3/8" THREADED ROD. WHERE CEILING HEIGHTS EXCEED 15', WALL MOUNT SENSORS AT 12'.

MANUAL ON, OVERRIDE OFFLOW VOLTAGE MOMENTARYSWITCH, PROVIDE MULTI-BUTTON SWITCH WHERE INDICATED BY SUBSCRIPT, SWITCH SHALL BEUNDER SINGLE GANG FACEPLATE.

24"

A

B

A

48"

WIDTH AS INDICATED ON PLANS

C

SLAB ON GRADE

KEY NOTE LEGEND

RECEPTACLES AS SHOWN

GROUND BUS ,W/ No. 250 KCMIL (G) WITH GREEN JACKET IN 1-1/4" C. BACK TO MDF TELECOMMUNICATIONS GROUND BAR .SEE GROUND BAR DETAIL.

PROVIDE No. 6 AWG GROUND WIRE TO EACH PIECE OF EQUIPMENT MOUNTED ON BACKBOARD.

A

B

C

GROUND CONNECTION FOR EQUIPMENT. COMPRESSION LUG BOLTS AND WIRE.

STAINLESS STEEL MOUNTING BRACKET, 1" OFFSET.

RED STANDOFF INSULATOR, POLYESTER/FIBERGLASS.

FRONT ELEVATION

A

WALL CONSTRUCTION SUITABLE FOR WALL ANCHOR (TYPICAL).

SECTION "A-A"

A

19" x 6" x 1/4" THICK COPPER GROUND BUS

3/8" MOUNTING BOLT.

2"1/4

"

NOTE: LOCATION INDICATED AS "TMGB" IN MDF ROOM AND "TGB" IN IDF ROOMS.

RE

LO

CA

TIO

NM

UN

ICIP

AL

CO

UR

T



www.btbbinc.com


ISSUANCES

18-025

PLANNERSARCH ITECTS

ARCHITECTS PLANNERS

CO

RN

ER

MU

LB

ER

RY

& S

EC

ON

D S

T.

MA

CO

N, G

EO

RG

IA@

BC

CH

FIR

ST

FLO

OR

E5.1

ELECTRICALDETAILS


NOTES:

40 A 24 A 17 A

4636 VA 2760 VA 1980 VA

41 20 A 1 SPARE 0 0 SPACE -- -- 42

39 20 A 1 SPARE 0 0 SPACE -- -- 40

37 20 A 1 SPARE 0 0 SPACE -- -- 38

35 20 A 1 SPARE 0 0 SPACE -- -- 36

33 20 A 1 SPARE 0 0 SPACE -- -- 34

31 20 A 1 SPARE 0 0 SPACE -- -- 32

29 20 A 1 SPARE 0 0 SPACE -- -- 30

27 20 A 1 SPARE 0 0 SPACE -- -- 28

25 20 A 1 SPARE 0 0 SPACE -- -- 26

23 20 A 1 SPARE 0 0 SPACE -- -- 24

21 20 A 1 RECEPTACLES 540 0 SPACE -- -- 22






9 20 A 1 COPIER 1500 0 SPACE -- -- 10




1 20 A 1 REFRIGERATOR (GFCI BKR) 1500 1516 LIGHTING 1 20 A 2

CKT TRIP P CIRCUIT DESCRIPTION A B C CIRCUIT DESCRIPTION P TRIP CKT

A.I.C. RATING: 10,000 TOTAL LOAD: 9376 VA

WIRES: 4 FED BY: RATING: INDOOR

PHASE: 3 MAINS TYPE: MLO MOUNTING: SURFACE

VOLTAGE: 120/208 WYE MAINS RATING: 125 A LOCATION: FILES 120

PANEL: L1

NOT TO SCALEE5.1

1 OCCUPANCY SENSOR WIRING

NOT TO SCALEE5.1

2 VACANCY SENSOR WIRING

No. 32283

RT

PROFESSIONAL

OEG

G I A

NE ER

IGNE

SIGER

ERED

O.Y

W

EO

L

M

S

M

E

A

W

CK

SCALE:NOT TO SCALEE5.1

3 BACKBOARD DETAIL

SCALE:NOT TO SCALEE5.1

4 TELECOMMUNICATIONS EQUIPMENT GROUND BUS

DD

D

RAMP DN.

RAMP UP

K-2032GREENW

ICHLAVATO

RYVITREO

US CHINA


DEPUTY CLERK

114

CL.

110

TL.

112

CL.

111

JUDGE'S CHAMBERS

113

CL.

108

TL.

107

PROBATION AIDE

105

PROBATION

104

DEPUTY CLERK

106

WAITING

101

CL.

103

TL.

102

MUNICIPALCOURTROOM

109

DEPUTY CLERK

115

WORK STATIONS

116

FRONT COUNTER

117

BREAK

122

FILES

121

FILES

120

CHIEF CLERK

119

COPY/SUPPLY

118

ALCOVE

123

FIRE PROTECTION NOTES:

1. MODIFY EXISTING SPRINKLER SYSTEM IN THE HATCHED AREAS TO PROVIDE COMPLETE PROTECTION FOR THE RENOVATED PORTIONS OF THE BUILDING.

2. IF THE SPRINKLER SYSTEM IS OUT OF SERVICE FOR MORE THAN FOUR HOURS IN A TWENTY FOUR HOUR PERIOD, THE AUTHORITY HAVING JURISDICTION SHALL BE NOTIFIED. THE BUILDING SHALL BE EVACUATED OR AN APPROVED FIRE WATCH SHALL BE PROVIDED FOR ALL PARTIES LEFT UNPROTECTED BY THE SHUTDOWN UNTIL THE SPRINKLER SYSTEM HAS BEEN RETURNED TO SERVICE (NFPA 101 LIFE SAFETY CODE, SECTION 9.7.6.1).

3. RENOVATIONS OR ALTERATIONS TO AN EXISTING SPRINKLER SYSTEM NEED TO BE IN ACCORDANCE WITH STATE OF GEORGIA RULES AND REGULATIONS OF THE SAFETY FIRE COMMISSIONER CHAPTER 120-3-3.

4. SPRINKLER CONTRACTOR TO PROVIDE SHOP DRAWINGS WITH HYDRAULIC CALCULATIONS TO THE STATE FIRE MARSHALL'S OFFICE FOR REVIEW.

5. CONTRACTOR TO VERIFY IF CURRENT SPRINKLER HEAD PLACEMENT IS APPROPRIATE FOR NEW SPACE ENCLOSURE. MODIFY AS NEEDED TO PROVIDE COMPLETE COVERAGE AS REQUIRED BY NFPA STANDARDS.


NOTE 5

NOTE 5

NOTE 5

RE

LO

CA

TIO

NM

UN

ICIP

AL

CO

UR

T



www.btbbinc.com


ISSUANCES

18-025

PLANNERSARCH ITECTS

ARCHITECTS PLANNERS

CO

RN

ER

MU

LB

ER

RY

& S

EC

ON

D S

T.

MA

CO

N, G

EO

RG

IA@

BC

CH

FIR

ST

FLO

OR

F1.1

FIRE PROTECTIONPLAN


SCALE: 1/8" = 1'-0"F1.1

1 FIRE PROTECTION PLAN

T

PROFESSIONAL

NEER

IGNE

SIGER

ERED

No. 36592

IGROEG

A

E

A

A.BSA

MOH

T

L

Date post:	19-Mar-2020
Category:	Documents
Upload:	others
View:	9 times
Download:	0 times

RELOCATION MUNICIPAL COURT @ BCCH FIRST FLOOR...@ bcch first floor municipal court courthouse bcch...

Documents